View
256
Download
3
Category
Preview:
Citation preview
RISER PIPES
STÜWA · Konrad Stükerjürgen GmbH
ConTEnTS
ZSM Riser Pipes
Riser Pipes with Flange Connection
Riser Hose
81Subject to technical changes/errors excepted
STÜWA Konrad Stükerjürgen GmbHHemmersweg 80D - 33397 Rietberg
Phone:Fax:E-Mail:Website:
riser pipes sizes from dn 50 to dn 250 lengths up to 6 m Wall thickness from 2.0 to 6.0 mm seamless or longitudinally seam-welded
ZSM RISER PIPES
Basic material
Stainless steel
S235JR (ST37-2) plastic-coated steel serves as a basic material, Rilsan-coated, approved for drinking water. Conforms to KTW requirements [official German recommendation concerning the levels of polymers in drinking water] as recommended by the German Federal Department of Health.
S235JR (ST37-2) galvanized steel serves as a basic material, only suitable to a limited extent for drinking water, to be used for flange connections only.
Properties and suitability
Stainless steel of various qualities depending on groundwater condition and temperature
M No. 1.4301 (X5CrNi18-10), AISI 304 This type of steel is resistant to water and slightly polluted waste water as well as weak organic and inorganic acids. Generally, it is resistant to a pH value up to approx. 4.5 in aggressive substances low in chloride.
M No. 1.4541 (X6CrNiTi18-10), AISI 351 This type of steel has excellent resistance properties to a variety of aggressive media. Furthermore, this material is characterised by good ductility.
M No. 1.4571 (X6CrNiMoTi17-12-2), AISI 316TiSimilar properties as 1.4404 but with guaranteed resistance to intergranular corrosion due to an increased titanium content.
Additional materials on request
82Subject to technical changes/errors excepted
STÜWA Konrad Stükerjürgen GmbHHemmersweg 80D - 33397 Rietberg
Phone:Fax:E-Mail:Website:
Thread
COnneCtiOns
RISER PIPES
The choice of connections largely depends on technical requirements and installation guidelines for construction sites.
4 connection types on offer:
riser pipes with welded neck flange riser pipes with smooth flange Zsm riser pipes threaded riser pipes
ZSM riser pipe conncections
minimum space requirement – in case of cramped installation conditions
Quick assembly/disassembly two rods – double safety two O-rings 1.4301, aisi 304 or 1.4571, aisi 316 stainless-steel
material size dn 50 to dn 250 nominal pressure 40 bar
Smooth flangeWelded neck flange
Connections outer diameter d3Nomional diameter DN 50 65 80 100 125 150 200 250
Welded neck flange, smooth flange DIN 4927
[mm] 165 185 200 220 250 285 340 405
ZSM connection [mm] 85 106 118 140 170 200 253 316
Thread with two O-rings compliant to DIN 4942
[mm] 76.1 88,9 108 133 159 188 238
S1
d3
O-sealing ring
Welded neck flange
Pipe compliant toDIN 2448, DIN 2458, DIN 2462-1, DIN 2463-1, DIN 17455
t
r
C
cable cut-out
d3
d1s
d3
d1s
d3
d1s
Hex screw DIN ISO 4014
Hex nutDIN ISO 4032
Disc compliant to DIN 125-1
Sealing gasket
Disc compliant toDIN 125-1
(only for coating kb and g)
Hex screw DIN ISO 4014
Hex nutDIN ISO 4032
Disc compliant to DIN 125-1
Sealing gasket
Disc compliant to DIN 125-1
(only for coating kb and g)
Threaded riser pipeZSM riser pipes
Smooth flange
Pipe compliant toDIN 2448, DIN 2458, DIN 2462-1, DIN 2463-1, DIN 17455
t
r
C
cable cut-out
d3
d1s
d3
d1s
d3
d1s
Hex screw DIN ISO 4014
Hex nutDIN ISO 4032
Disc compliant to DIN 125-1
Sealing gasket
Disc compliant toDIN 125-1
(only for coating kb and g)
Hex screw DIN ISO 4014
Hex nutDIN ISO 4032
Disc compliant to DIN 125-1
Sealing gasket
Disc compliant to DIN 125-1
(only for coating kb and g)
ZSM
Rod
O-sealing ring
Dirt-repellant device
Anti-twist-protection
S1
d3
d2
83Subject to technical changes/errors excepted
STÜWA Konrad Stükerjürgen GmbHHemmersweg 80D - 33397 Rietberg
Phone:Fax:E-Mail:Website:
TECHNICAL DATA
RiSER PiPES
Cable notchesNominal diameter
DN 50 65 80 100 125 150 200
PN 16 16 16 16 16 16 16
c [mm] 48 48 48 55 65 75 60
r [mm] 15 15 15 20 30 35 20
t [mm] 30 30 30 30 30 35 35
Flanges with 2 cable notches each on both sides, optionally staggered by 180° or 90°. Additional notches on request.
Pipe compliant toDIN 2448, DIN 2458, DIN 2462-1, DIN 2463-1, DIN 17455
t
r
C
cable cut-out
d3
d1s
d3
d1s
d3
d1s
Hex screw DIN ISO 4014
Hex nutDIN ISO 4032
Disc compliant to DIN 125-1
Sealing gasket
Disc compliant toDIN 125-1
(only for coating kb and g)
Hex screw DIN ISO 4014
Hex nutDIN ISO 4032
Disc compliant to DIN 125-1
Sealing gasket
Disc compliant to DIN 125-1
(only for coating kb and g)
Pipe and flange connections
Pipe compliant toDIN 2448, DIN 2458, DIN 2462-1, DIN 2463-1, DIN 17455
t
r
C
cable cut-out
d3
d1s
d3
d1s
d3
d1s
Hex screw DIN ISO 4014
Hex nutDIN ISO 4032
Disc compliant to DIN 125-1
Sealing gasket
Disc compliant toDIN 125-1
(only for coating kb and g)
Hex screw DIN ISO 4014
Hex nutDIN ISO 4032
Disc compliant to DIN 125-1
Sealing gasket
Disc compliant to DIN 125-1
(only for coating kb and g)
84Subject to technical changes/errors excepted
STÜWA Konrad Stükerjürgen GmbHHemmersweg 80D - 33397 Rietberg
Phone:Fax:E-Mail:Website:
RISER PIPES
HOse risersThe flexible hose riser is a product which has been devel-oped for special cases of application.
The hose is manufactured in the extrusion procedure as a highly wear-resistant flat hose. The inner and outer sheath consist of polyurethane (PU) and are provided with a round woven polyester insert. In order to simplify the mounting of cables and immersion electrodes, a polyurethane-reinforced belt has been vulcanized on the hose with loops.
Advantages little space requirement for storage and transport Quick assembly and disassembly, especially in the case
of temporarily limited use trinkwasserzulassung [German drinking water stand-
ards] according to KtW [plastics in contact with drink-ing water]
Areas of application: drainage mining and industry agricultural irrigation Water monitoring test well Waste disposal drainage
Optional accerssories: reel support clamps centring devices
Hose coupling
Technical dataDiameter Inch 1 1 ¼ 1 ½ 2 2 ½ 3 4 5 6
mm 25 32 38 51 65 76 102 127 152
Burst pressure [bar] 50 90 65 57 57 57 57 57 57
Tensile strength [kg] 750 3.450 3.450 4.000 5.500 7.000 12.000 15.000 20.000
Max. recommended continuous load (a) [kg] 180 700 700 1.600 2.200 2.800 4.800 6.000 8.000
Weight without coupling [gr/m] 165 270 350 570 800 980 1.400 2.000 2.610
Max. installation depth [m] 100 300 260 260 260 260 260 260 260
Lengthening - max. [%] 2 2 2 2 2 2 2 2 2
Elongation - max. [%] 15 15 15 15 15 15 15 15 15
Max. working pressure [bar] 15 30 26 26 26 26 26 26 26
Maximum recommended throughput [l/min] 120 200 270 500 800 1.200 2.000 3.000 4.500
Operating temperature [°C] -40° to +50° C
ph value in the case of water below 30°C 4 to 9
ph value in the case of water from 30 to- 50°C 5 to 9
Length [m] 200 m reeled on spoil, other lengths upon request
Detail: loop
Recommended