View
8
Download
0
Category
Preview:
Citation preview
R2AP Panel Control Board
Powerful graphics processing board, providing high-quality images for TFT
panel with superior resolution up to UHD 4096x2160. Various signal input:
VGA, HDMI, analog RGB, and output formats: LVDS, eDP & V-by-one
V110
User Manual Version 1.0
Manual Number: 91521112100N
User Manual II
Preface
Copyright Notice
No part of this document may be reproduced, copied, translated, or transmitted in any form or by any means, electronic or mechanical, for any purpose, without the prior written permission of the original manufacturer.
Trademark Acknowledgement Brand and product names are trademarks or registered trademarks of their respective owners.
Disclaimer We reserve the right to make changes, without notice, to any product, including circuits and/or software described or contained in this manual in order to improve design and/or performance. We assume no responsibility or liability for the use of the described product(s), conveys no license or title under any patent, copyright, or masks work rights to these products, and makes no representations or warranties that these products are free from patent, copyright, or mask work right infringement, unless otherwise specified. Applications that are described in this manual are for illustration purposes only. We make no representation or warranty that such application will be suitable for the specified use without further testing or modification.
Warranty We warrant that each of its products will be free from material and workmanship defects for a period of one year from the invoice date.(Standard is one year, extended warranty will need to discuss with our sales representatives. If the customer discovers a defect, we will, at its option, repair or replace the defective product at no charge to the customer, provided it is returned during the warranty period of one year, with transportation charges prepaid. The returned product must be properly packaged in its original packaging to obtain warranty service. If the serial number and the product shipping data differ by over 30 days, the in-warranty service will be made according to the shipping date. In the serial numbers the third and fourth two digits give the year of manufacture, and the fifth digit means the month (e. g., with A for October, B for November and C for December). For example, the serial number 1W16Axxxxxxxx means October of year 2016.
User Manual III
Packing List Before using this Motherboard, please make sure that all the items listed below are present in your package: R2AP A/D Board User Manual Driver CD If any of these items are missing or damaged, contact your distributor or sales representative immediately.
Customer Service We provide a service guide as below for any problem by the following steps: First, contact your distributor, sales representative, or our customer service center for technical support if you need additional assistance. You need to prepare the following information before you call: Product serial number Peripheral attachments Software (OS, version, application software, etc.) Detailed problem description The exact wording of any error messages In addition, free technical support is available from our engineers every business day. We are always ready to give advice on application requirements or specific information on the installation and operation of any of our products. Please do not hesitate to call or e-mail us.
User Manual IV
Advisory Conventions
Four types of advisories are used throughout the user manual to provide helpful
information or to alert you to the potential for hardware damage or personal injury.
These are Notes, Important, Cautions, and Warnings. The following is an example of
each type of advisory.
NOTE:
A note is used to emphasize helpful information
IMPORTANT:
An important note indicates information that is important for you to
know.
CAUTION
A Caution alert indicates potential damage to hardware and explains how
to avoid the potential problem.
WARNING!
An Electrical Shock Warning indicates the potential harm from electrical
hazards and how to avoid the potential problem.
User Manual V
Safety Precautions
CAUTION
Always ground yourself to remove any static charge before
touching the board. Modern electronic devices are very sensitive to
static electric charges. As a safety precaution, use a grounding wrist
strap at all times. Place all electronic components in a
static-dissipative surface or static-shielded bag when they are not
in the chassis.
Safety and Warranty
1. Please read these safety instructions carefully.
2. Please keep this user manual for later reference.
3. Please disconnect this equipment from any AC outlet before cleaning. Do not
use liquid or spray detergents for cleaning. Use a damp cloth.
4. For pluggable equipment, the power outlet must be installed near the
equipment and must be easily accessible.
5. Keep this equipment away from humidity.
6. Put this equipment on a reliable surface during installation. Dropping it or
letting it fall could cause damage.
7. Make sure the voltage of the power source is correct before connecting the
equipment to the power outlet.
8. Position the power cord so that people cannot step on it. Do not place anything
over the power cord.
9. All cautions and warnings on the equipment should be noted.
10. If the equipment is not used for a long time, disconnect it from the power
source to avoid damage by transient over-voltage.
11. If any of the following situations arises, get the equipment checked by service
personnel:
A. The power cord or plug is damaged.
B. Liquid has penetrated into the equipment.
C. The equipment has been exposed to moisture.
D. The equipment does not work well, or you cannot get it to work according
to the user’s manual.
E. The equipment has been dropped and damaged.
F. The equipment has obvious signs of breakage.
User Manual VI
Revision History
User Manual
Version Board Version Date Note Author
1.0 V110 4-May-2016 Initial release Austin Chang
User Manual VII
Contents
Table of Contents
PREFACE .............................................................................................................................................. I
CHAPTER 1 GENERAL INFORMATION ................................................................................................ 10
1.1 INTRODUCTION ................................................................................................................................. 10
1.2 FEATURES ........................................................................................................................................ 10
1.3 HARDWARE SPECIFICATIONS ................................................................................................................ 11
1.4 FUNCTIONAL DESCRIPTION.................................................................................................................. 12
1.5 PHYSICAL DESCRIPTION ...................................................................................................................... 13
CHAPTER 2 HARDWARE INSTALLATION ............................................................................................ 15
2.1 MOTHERBOARD COMPONENTS ............................................................................................................ 15
2.1.1 Front Side ............................................................................................................................. 15
2.1.2 Rear Side .............................................................................................................................. 16
2.1.3 I/O Side ................................................................................................................................. 16
2.2 I/O EQUIPMENT INSTALLATION ............................................................................................................ 17
2.2.1 Power ................................................................................................................................... 17
2.2.2 Power Cable ......................................................................................................................... 17
2.3 OPTIONS ......................................................................................................................................... 17
2.3.1 VGA Cable ............................................................................................................................ 17
2.3.2 DVI-D Cable .......................................................................................................................... 17
2.3.3 HDMI Cable .......................................................................................................................... 17
2.3.4 Display Port Cable ................................................................................................................ 17
2.3.5 RS-232 Cable ........................................................................................................................ 18
2.4 CONNECTOR PIN ASSIGNMENT ............................................................................................................ 18
2.4.1 Connectors Guide ................................................................................................................. 19
2.5 I/O SIDE ......................................................................................................................................... 34
CHAPTER 3 USING THE LCD MONITOR .............................................................................................. 40
3.1 OSD KEY FUNCTIONS ........................................................................................................................ 40
3.2 OSD MENU NAVIGATION ................................................................................................................... 41
3.2.1 Display .................................................................................................................................. 42
3.2.2 Adjust ................................................................................................................................... 43
3.2.3 Audio .................................................................................................................................... 44
3.2.4 Multi-Display ........................................................................................................................ 44
User Manual VIII
3.2.5 OSD....................................................................................................................................... 45
3.2.6 Advanced .............................................................................................................................. 46
CHAPTER 4 TROUBLESHOOTING ....................................................................................................... 49
APPENDIX A SUPPORTED MODES .................................................................................................... 51
APPENDIX C REMOTE CONTROL SET COMMAND ............................................................................. 57
APPENDIX D REMOTE CONTROL GET COMMAND ............................................................................ 63
APPENDIX E ELECTRICAL CHARACTERISTICS ..................................................................................... 69
R2AP Panel Control Board General Information
User Manual 9
General Information This chapter includes the R2AP panel control board background information.
R2AP Panel Control Board General Information
User Manual 10
Chapter 1 General Information
This chapter includes the R2AP Panel Control Board background information.
1.1 Introduction
Thank you for choosing R2AP Panel Control Board. The Winmate R2AP is a
powerful graphic processing board, providing High quality images for TFT panels
from VGA (640 x 480) up to DCI 4K (4096 x 2160) and can be used in a variety of
systems. The R2AP provides all A/D board key functions required for image capture,
processing and display timing control, other functions include PIP / PBP – 4P function,
Image rotation (90, 180, 270 deg.), OSD rotation (90,270 deg.), and programmable
12-bit LUT.
With all these functions integrated onto a single board, the R2AP is able to keep
up with the cost of high-end multimedia LCD monitors while maintaining a high
degree of flexibility and quality. It is suitable for large size and high resolution panels
and meets the demanding performance requirements of today’s business and
industrial applications. A single board reduces the costs of high-end multimedia LCD
monitors, meanwhile maintaining high degree of flexibility and quality.
1.2 Features
Support high resolution up to 4096 x 2160 @ 60Hz.
Support multiple panel interface including 10-bit LVDS, V-by-One and eDP.
Content protection HDCP 1.4 is supported with HDMI.
VGA support Sync-On-Green (SOG) and composite mode.
RS-232 remote control by user operation.
With IR remote control.
12/24V input (with jumper setting).
Operating temperature 0 to 60°C.
Storage temperature -10 to 60° C.
R2AP Panel Control Board General Information
User Manual 11
1.3 Hardware Specifications
System Specification:
Scaler RTD2796B-CG
Internal Connector:
To Backlight Unit Wafer
IR Sensor Wafer
GPIO Reserved
I2C Reserved
OSD Key Pad Wafer
5V 5V / 1A Output wafer
12V 12V / 1A Output wafer
Output Interface (internal):
LVDS Hirose-DF13DP-1.25V
V-By-One V-by-One Output Connector
eDP Hirose-DF13DP-1.25V
Input Signal:
DVI-D Dual Link DVI-D
HDMI1.4 Type A
HDMI2.0 Type A
Display Port1.2 Display Port1.2
VGA D-Sub 15Pin
Audio Line In 3.5mm Stereo Input
Audio In /Out:
Speaker Output 8W, class D
Power Requirements:
Power Input Din 4 Pin (12V / 24V setting by jumper)
(*Default 12V)
Power Output Wafer
Mechanical:
Dimensions (W x H x D) 167 x 120mm
Environment:
Operating Temperature 0°~+60°C
Storage Temperature -10°~+60°C
Operating Humidity 30%~ 90% (non-condensing, RH)
R2AP Panel Control Board General Information
User Manual 12
Certification:
Electromagnetic CE, FCC
1.4 Functional Description
Function block(V110)
R2AP Panel Control Board General Information
User Manual 13
1.5 Physical Description
Board Dimensions (V110)
R2AP Panel Control Board Hardware Installation
User Manual 14
Hardware Installation This chapter provides information on how to use
jumpers and connectors on the R2AP panel control
board.
R2AP Panel Control Board Hardware Installation
User Manual 15
Chapter 2 Hardware Installation
This chapter provides information on how to use jumpers and connectors on the
R2AP control board. Be cautious while working with these modules. Carefully read
the content of this chapter in order to avoid any damages.
2.1 Motherboard Components
2.1.1 Front Side
R2AP Panel Control Board Hardware Installation
User Manual 16
2.1.2 Rear Side
2.1.3 I/O Side
NOTE:
Some connectors are optional depends on your order.
SW1
USB 2.0
Mini-PCIE
Half Card
R2AP Panel Control Board Hardware Installation
User Manual 17
2.2 I/O Equipment Installation
This chapter provides information on how to use jumpers and connectors on the
R2AP A/D Board. Be cautious while working with these modules. Please carefully
read the content of this chapter in order to avoid any damages.
2.2.1 Power
Switch off the power on the monitor and the Keypad. The power switch is located at
the most right button of the keypad.
2.2.2 Power Cable
Connect the power cord to monitor, and then connect the power to the AC outlet
through the AC/DC adapter.
2.3 Options
The R2AP panel control port is designed for monitors that work with a variety of
compatible video sources. Due to the possible deviations between these signal
sources, you may have to make adjustments to the monitor settings from the OSD
menu when switching between these sources.
2.3.1 VGA Cable
Plug 15-pin VGA signal cable to the VGA connector in the rear of motherboard, and
plug the other end to the monitor. Secure cable connectors with hexagonal copper
pillars M3x4mm.
2.3.2 DVI-D Cable
Plug in DVI-D signal cable to the DVI-D connector on the rear side of the
motherboard, and plug in the other end to the monitor. Secure cable connectors
with hexagonal copper pillars M3x4mm.
2.3.3 HDMI Cable
Plug HDMI signal cable to the HDMI connector on the rear side of PC system, and
plug the other end to the monitor. Secure cable connectors hexagonal copper pillars
M3x4mm.
2.3.4 Display Port Cable
Plug display port signal cable to the Display port connector on the rear side of PC
system, and plug in the other end to the monitor. Secure cable connectors with
R2AP Panel Control Board Hardware Installation
User Manual 18
hexagonal copper pillars M3x4mm.
2.3.5 RS-232 Cable
You will be able to develop your own application software utilizing built-in RS-232
command code. The application software can send command from PC to LCD
monitor via RS-232 port to control LCD monitor. Please refer to Appendix B for
built-in RS-232 command code.
2.4 Connector Pin Assignment
This section explains how to set jumpers for correct configuration of the
motherboard.
NOTE:
A pair of needle nose pliers may be helpful when working with jumpers.
If you have any doubts about the best hardware configuration for your
application, contact your local distributor or sales representative before
you make any changes. Generally, you simply need a standard cable to
make most connections.
The jumper setting diagram is shown below. When the jumper cap is placed on both
pins, the jumper is SHORT. The illustration below shows a 3-pin jumper; pins 1 and 2
are short. If you remove the jumper cap, the jumper is OPEN.
1
2
3
R2AP Panel Control Board Hardware Installation
User Manual 19
2.4.1 Connectors Guide
The table below shows each of front side connectors and its functions.
Connector Function Note
CN3 VGA Input Wafer JST-B13B-PH-K-S or equivalent
CN9 OSD Key Pad Wafer 1*10p P=2.0mm DIP 180°
CN12 Stereo Line Output Wafer 6p P:1.0mm SMD 180° white
CNF1 V-by-One Output Connector FI-RESIS-HF 51p JAE
J5 Speaker Output JST-B4B-PH-K-S or equivalent.
J6 LVDS output- A Hirose-DF13DP-1.25V
J7 To Backlight Unit JST-B7B-PH-K-S or equivalent
J8 LVDS output- B Hirose-DF13DP-1.25V
J9 Panel Power Selector Header 2*3p P:2.54mm DIP 180°
J10 LVDS output- C Hirose-DF13DP-1.25V
J11 LVDS output- D Hirose-DF13DP-1.25V
J12 IR Sensor JST-B3B-PH-K-S or equivalent
J14 GPIO JST-B3B-PH-K-S or equivalent.
J15 I2C JST-B4B-PH-K-S or equivalent.
J16 Power Din 4 Pin Input Power Jack Din 4p dip Quick Lock
J17 Power Wafer Input 2.0mm 2 x 6 Pin Header DIP180°
J18 Power Wafer Output JST-B20B-PHDSS or equivalent
J19 12V/1A Output JST-B2B-PH-K-S or equivalent
J20 5V/1A Output JST-B2B-PH-K-S or equivalent
J21 3.3V/1A Output JST-B2B-PH-K-S or equivalent
J22 eDP Output Wafer Hirose-DF13DP-1.25V
J24 UART Wafer 2.54mm 1 x 4 pin header
J25 GPIO JST-B3B-PH-K-S or equivalent
JP2 Hanns (10.1”) (optional
connector)
Header 1*3p P=2.00mm DIP 180°
JP5 24V/12V Selector for Power
Input
Header 2*4p P:2.54mm DIP 180°
JP6 DC/PWM Select Connector Header 1*3p P:2.54mm DIP 180°
JP7 12V/5V Selector for BLU Power Header 2*4p P:2.54mm DIP 180°
JP8 PWM Level(5V/3.3V)Select
Connector
Header 1*3p P=2.00mm DIP 180°
R2AP Panel Control Board Hardware Installation
User Manual 20
CN3:VGA Input Wafer
Pin No. Description
1 Red+
2 Red-
3 Green+
4 Green-
5 Blue+
6 Blue-
7 SDA
8 HS
9 VS
10 Cable Detect
11 SCL
12 GND
13 VGA 5V
CN9: OSD Key Pad Wafer
Pin No. Symbol Description
1 PWR Power LED
2 PWR_SW Power on/off control
3 - Right key
4 > Increase
5 < Decrease
6 NC No connection
7 + Left key
8 STB Standby LED
9 GND Ground
10 +5V DC 5V
R2AP Panel Control Board Hardware Installation
User Manual 21
CN12: Stereo Line Output
CNF1: V-by-One Output Connector
Pin No. Symbol Description
1 GND Ground
2 TX7P Positive V-by-One differential data output Lane 7
3 TX7N Negative V-by-One differential data output Lane 7
4 GND Ground
5 TX6P Positive V-by-One differential data output Lane 6
6 TX6N Negative V-by-One differential data output Lane 6
7 GND Ground
8 TX5P Positive V-by-One differential data output Lane 5
9 TX5N Negative V-by-One differential data output Lane 5
10 GND Ground
11 TX4P Positive V-by-One differential data output Lane 4
12 TX4N Negative V-by-One differential data output Lane 4
13 GND Ground
14 TX3P Positive V-by-One differential data output Lane 3
15 TX3N Negative V-by-One differential data output Lane 3
16 GND Ground
17 TX2P Positive V-by-One differential data output Lane 2
18 TX2N Negative V-by-One differential data output Lane 2
19 GND Ground
20 TX1P Positive V-by-One differential data output Lane 1
Pin No. Description
1 LINEOUT_DET
2 AUD_R1_OUT
3 RINP
4 LINP
5 AUD_L1_OUT
6 GND
R2AP Panel Control Board Hardware Installation
User Manual 22
21 TX1N Negative V-by-One differential data output Lane 1
22 GND Ground
23 TX0P Positive V-by-One differential data output Lane 0
24 TX0N Negative V-by-One differential data output Lane 0
25 GND Ground
26 LOCKN Lock detect input
27 HTPDN Hot plug detect input
28 8b_10b 8bit /10bit Select
29 NC No Connection
30 LD_EN Local Dimming Mode Enable
31 2nd AUX_P 2ndAUX_P
32 2nd AUX_N 2ndAUX_N
33 SCL I2C Clock signal
34 SDA I2C Data signal
35 2D3D 2D/3D Enable
36 LR Input signal for Glasses Left Right signal
37 LRI Output signal for Left/Right synchronous signal
38 1st AUX_P 1st AUX_P
39 1st AUX_N 1st AUX_N
40 GND Ground
41 GND Ground
42 GND Ground
43 NC No Connection
44 PNL_PWR Power output (+12V)
45 PNL_PWR Power output (+12V)
46 PNL_PWR Power output (+12V)
47 PNL_PWR Power output (+12V)
48 PNL_PWR Power output (+12V)
49 PNL_PWR Power output (+12V)
50 PNL_PWR Power output (+12V)
51 PNL_PWR Power output (+12V)
R2AP Panel Control Board Hardware Installation
User Manual 23
J5: Speaker Output
J6: Bits LVDS output- A
Pin No. Symbol
1 LOUT+
2 LOUT-
3 ROUT-
4 ROUT+
Pin No. Symbol Description
1 PWR Panel power
2 ATX0- LVDS negative A bit 0
3 PWR Panel power
4 ATX0+ LVDS positive A bit 0
5 NC Not Connect
6 ATX1- LVDS negative A bit 1
7 GND Ground
8 ATX1+ LVDS positive A bit 1
9 SDA I2C SDA
10 ATX2- LVDS negative A bit 2
11 SCL I2C SCL
12 ATX2+ LVDS positive A bit 2
13 GND Ground
14 ACLKTX- LVDS negative A clock
15 GND Ground
16 ACLKTX+ LVDS positive A clock
17 ATX4- LVDS negative A bit 4
18 ATX3- LVDS negative A bit 3
19 ATX4+ LVDS positive A bit 4
20 ATX3+ LVDS positive A bit 3
21 GND Ground
22 BTX0- LVDS negative B bit 0
R2AP Panel Control Board Hardware Installation
User Manual 24
J7: To Backlight Unit
23 BTRL1 Optional
24 BTX0+ LVDS positive B bit 0
25 BTRL2 Optional
26 BTX1- LVDS negative B bit 1
27 BTRL3 Optional
28 BTX1+ LVDS positive B bit 1
29 BTRL4 Optional
30 BTX2- LVDS negative B bit 2
31 BTRL5 Optional
32 BTX2+ LVDS positive B bit 2
33 GND Ground
34 BCLKTX- LVDS negative B clock
35 GND Ground
36 BCLKTX+ LVDS positive B clock
37 BTX4- LVDS negative Bbit 4
38 BTX3- LVDS negative Bbit 3
39 BTX4+ LVDS positive B bit 4
40 BTX3+ LVDS positive Bbit 3
Pin No. Symbol
1 +12V
2 +12V
3 +12V
4 GND
5 ADJ
6 GND
7 ON/OFF
R2AP Panel Control Board Hardware Installation
User Manual 25
J8: Bits LVDS Output- B
Pin No. Symbol Description
1 PWR Panel power
2 DTX0- LVDS negative D bit 0
3 PWR Panel power
4 DTX0+ LVDS positive D bit 0
5 NC Not Connect
6 DTX1- LVDS negative D bit 1
7 GND Ground
8 DTX1+ LVDS positive D bit 1
9 GND Ground
10 DTX2- LVDS negative D bit 2
11 GND Ground
12 DTX2+ LVDS positive D bit 2
13 GND Ground
14 DCLKTX- LVDS negative D clock
15 GND Ground
16 DCLKTX+ LVDS positive D clock
17 DTX4- LVDS negative D bit 4
18 DTX3- LVDS negative D bit 3
19 DTX4+ LVDS positive D bit 4
20 DTX3+ LVDS positive D bit 3
21 GND Ground
22 CTX0- LVDS negative C bit 0
23 GND Ground
24 CTX0+ LVDS positive C bit 0
25 GND Ground
26 CTX1- LVDS negative C bit 1
27 GND Ground
28 CTX1+ LVDS positive C bit 1
29 GND Ground
30 CTX2- LVDS negative C bit 2
R2AP Panel Control Board Hardware Installation
User Manual 26
31 GND Ground
32 CTX2+ LVDS positive C bit 2
33 GND Ground
34 CCLKTX- LVDS negative C clock
35 GND Ground
36 CCLKTX+ LVDS positive C clock
37 CTX4- LVDS negative C bit 4
38 CTX3- LVDS negative C bit 3
39 CTX4+ LVDS positive C bit 4
40 CTX3+ LVDS positive C bit 3
J9: Panel Power Selector
Pin No. Description
1-2 Short pin 1-2 to set +3.3V
3-4 Short pin 3-4 to set +5V
5-6 Short pin 5-6 to set +12V
J10: Bits LVDS output- C
Pin No. Symbol Description
1 PWR Panel power
2 ETX0- LVDS negative E bit 0
3 PWR Panel power
4 ETX0+ LVDS positive E bit 0
5 NC Not Connect
6 ETX1- LVDS negative E bit 1
7 GND Ground
R2AP Panel Control Board Hardware Installation
User Manual 27
8 ETX1+ LVDS positive E bit 1
9 SDA I2C SDA
10 ETX2- LVDS negative E bit 2
11 SCL I2C SCL
12 ETX2+ LVDS positive E bit 2
13 GND Ground
14 ECLKTX- LVDS negative E lock
15 GND Ground
16 ECLKTX+ LVDS positive E clock
17 ETX4- LVDS negative E bit 4
18 ETX3- LVDS negative E bit 3
19 ETX4+ LVDS positive E bit 4
20 ETX3+ LVDS positive E bit 3
21 GND Ground
22 FTX0- LVDS negative F bit 0
23 FTRL1 Optional
24 FTX0+ LVDS positive F bit 0
25 FTRL2 Optional
26 FTX1- LVDS negative F bit 1
27 FTRL3 Optional
28 FTX1+ LVDS positive F bit 1
29 FTRL4 Optional
30 FTX2- LVDS negative F bit 2
31 FTRL5 Optional
32 FTX2+ LVDS positive F bit 2
33 GND Ground
34 FCLKTX- LVDS negative F clock
35 GND Ground
36 FCLKTX+ LVDS positive F clock
37 FTX4- LVDS negative Fbit 4
38 FTX3- LVDS negative Fbit 3
39 FTX4+ LVDS positive F bit 4
40 FTX3+ LVDS positive Fbit 3
R2AP Panel Control Board Hardware Installation
User Manual 28
J11: Bits LVDS output- D
Pin No. Symbol Description
1 PWR Panel power
2 GTX0- LVDS negative G bit 0
3 PWR Panel power
4 GTX0+ LVDS positive G bit 0
5 NC Not Connect
6 GTX1- LVDS negative G bit 1
7 GND Ground
8 GTX1+ LVDS positive G bit 1
9 GND Ground
10 GTX2- LVDS negative G bit 2
11 GND Ground
12 GTX2+ LVDS positive G bit 2
13 GND Ground
14 GCLKTX- LVDS negative G clock
15 GND Ground
16 GCLKTX+ LVDS positive G clock
17 GTX4- LVDS negative G bit 4
18 GTX3- LVDS negative G bit 3
19 GTX4+ LVDS positive G bit 4
20 GTX3+ LVDS positive G bit 3
21 GND Ground
22 HTX0- LVDS negative H bit 0
23 GND Ground
24 HTX0+ LVDS positive H bit 0
25 GND Ground
26 HTX1- LVDS negative H bit 1
27 GND Ground
28 HTX1+ LVDS positive H bit 1
29 GND Ground
30 HTX2- LVDS negativeH bit 2
R2AP Panel Control Board Hardware Installation
User Manual 29
31 GND Ground
32 HTX2+ LVDS positive H bit 2
33 GND Ground
34 HCLKTX- LVDS negative H clock
35 GND Ground
36 HCLKTX+ LVDS positive H clock
37 HTX4- LVDS negative Hbit 4
38 HTX3- LVDS negative Hbit 3
39 HTX4+ LVDS positive H bit 4
40 HTX3+ LVDS positive Hbit 3
J12: IR Sensor
J14: GPIO
J15: I2C
Pin No. Symbol
1 IR
2 GND
3 +5V
Pin No. Symbol
1 +5V
2 GND
3 GPIO
Pin No. Symbol
1 +5V
2 SDA
3 SCL
4 GND
R2AP Panel Control Board Hardware Installation
User Manual 30
J17: Power Wafer Input
J18: Power Wafer Output
Pin No. Symbol
1 +12V/+24V
2 +12V/+24V
3 +12V/+24V
4 +12V/+24V
5 +12V/+24V
6 +12V/+24V
7 +12V/+24V
8 +12V/+24V
9 +12V/+24V
10 +12V/+24V
11 GND
12 GND
13 GND
14 GND
15 GND
16 GND
17 GND
Pin No. Symbol
1 +12V/+24V
2 +12V/+24V
3 +12V/+24V
4 +12V/+24V
5 +12V/+24V
6 +12V/+24V
7 GND
8 GND
9 GND
10 GND
11 GND
12 GND
R2AP Panel Control Board Hardware Installation
User Manual 31
18 GND
19 GND
20 GND
J19: 12V/1A Output
J20: 5V/1A Output
J21: 3.3V/1A Output
Pin No. Symbol
1 +12V
2 GND
Pin No. Symbol
1 +5V
2 GND
Pin No. Symbol
1 +3.3V
2 GND
R2AP Panel Control Board Hardware Installation
User Manual 32
J22: eDP Output Wafer
Pin No. Symbol Pin No. Symbol
1 AUXN 2 SCL
3 AUXP 4 SDA
5 GND 6 HDMI_MHL
7 L3N 8 DP
9 L3P 10 HDMI_MHL
11 GND 12 TX_HDD
13 L2N 14 GND
15 L2P 16 GND
17 GND 18 GND
19 L1N 20 GND
21 L1P 22 PWR
23 GND 24 PWR
25 L0N 26 PWR
27 L0P 28 PWR
29 GND 30 +3.3V_DP
J24: UART Wafer
J25: Reserved GPIO
Pin No. Symbol Description
1 +5V +5V
2 TXD UART Transmit Signal
3 RXD UART Receive Signal
4 GND Ground
Pin No. Description
1 GPIO
2 GPIO
3 GPIO
4 GPIO
R2AP Panel Control Board Hardware Installation
User Manual 33
JP2: Hanns (10.1”) Optional Connector
JP5: Selector for Power Input 24V/ 12V
Pin No. Description
1-2 , 3-4 24V
5-6 , 7-8 12V (default)
JP6: Brightness Control (PWM or DC control)
Pin No. Description
1-2 Hannstar(10.1”) Connector
2-3 Normal Connector
Pin No. Description
1-2 DC voltage
2-3 PWM signal
R2AP Panel Control Board Hardware Installation
User Manual 34
JP7: Selector for BLU Power 12V/ 5V
Pin No. Description
1-2 , 3-4 12V
5-6 , 7-8 5V
JP8: Adjust PWM Level (5V/3.3V) Connector
2.5 I/O Side
The table below shows each of I/O side connectors and its functions.
Connector Description
CN2 DVI-D input
CN4 Display port input
CN7 HDMI 2.0 input
J3 Audio-in, 3.5mm stereo input
U9 VGA D-Sub 9 input
CN15 HDMI 1.4 input
Pin No. Symbol Description
1-2 PWM_5V PWM 5V Connector
2-3 PWM_3V3 PWM 3.3V Connector
R2AP Panel Control Board Hardware Installation
User Manual 35
CN2: DVI-D
CN4: Display Port Input
Pin № Symbol Pin № Symbol
1 DVI_RX2- 2 DVI_RX2-
3 GND 4 4-
5 4+ 6 DVI SCL
7 DVI SDA 8 NC
9 DVI_RX1- 10 DVI_RX1+
11 GND 12 3-
13 3+ 14 +5V
15 DVI_CON_CABLE 16 DVI_CON_HP
17 DVI_RX0- 18 DVI_RX0+
19 GND 20 5-
21 5+ 22 GND
23 DVI_CLKP 24 DVI_CLKN
C1 NC C2 NC
C3 NC C4 NC
C5 NC
Pin № Name Pin № Name
1 Lane 0 2 GND
3 Lane 0 4 Lane 1
5 GND 6 Lane 1
7 Lane 2 8 GND
9 Lane 2 10 Lane 3
11 GND 12 Lane 3
13 GND 14 Lane 3
15 AUX 16 GND
17 AUX 18 Hot Plug
19 Return 20 DP_PWR
R2AP Panel Control Board Hardware Installation
User Manual 36
CN7: HDMI 2.0
J3: Audio-in
Pin No. Description
1 HDMI_RX2+
2 GND
3 HDMI_RX2-
4 HDMI_RX1+
5 GND
6 HDMI_RX1-
7 HDMI_RX0+
8 GND
9 HDMI_RX0-
10 HDMI_RXC+
11 GND
12 HDMI_RXC-
13 HDMI_CON_CEC
14 NC
15 HDMI_CON_SCL
16 HDMI_CON_SDA
17 HDMI_CON_CABLE
18 +5V_HDMI
19 HDMI_CON_HP
Pin № Symbol
1 GND
2 LINE_IN_L
3 NC
4 LINE_IN_R
5 NC
R2AP Panel Control Board Hardware Installation
User Manual 37
U9: VGA D-Sub 9
CN15: HDMI 1.4 Input
Pin № Symbol Pin № Symbol
1 RED 2 GREEN
3 BLUE 4 NC
5 GND 6 RED_RTN
7 GREEN_RTN 8 BLUE_RTN
9 KEY/PWR 10 GND
11 NC 12 SDA
13 H Sync 14 V Sync
15 SCL
Pin No. Description
1 HDMI_RX2+
2 GND
3 HDMI_RX2-
4 HDMI_RX1+
5 GND
6 HDMI_RX1-
7 HDMI_RX0+
8 GND
9 HDMI_RX0-
10 HDMI_RXC+
11 GND
12 HDMI_RXC-
13 HDMI_CON_CEC
14 NC
15 HDMI_CON_SCL
16 HDMI_CON_SDA
17 HDMI_CON_CABLE
18 +5V_HDMI
19 HDMI_CON_HP
R2AP Panel Control Board Hardware Installation
User Manual 38
DC Input: Power 24/12V In
Pin № Symbol Pin № Symbol
1 DC_IN 2 GND
3 DC_IN 4 GND
R2AP Panel Control Board Using the LCD Monitor
User Manual 39
Using the LCD Monitor This chapter contains operating LCD monitor
guide. You can find OSD key definitions and
menu navigation in this chapter.
R2AP Panel Control Board Using the LCD Monitor
User Manual 40
Chapter 3 Using the LCD Monitor
This chapter contains operating LCD monitor guide. You can find OSD key
definitions and menu navigation in this chapter.
3.1 OSD Key Functions
Icon Function
Decrease the value / Select up or down
Increase the value / Select up or down
Power switch
Select left
Select right / Call main OSD menu
R2AP Panel Control Board Using the LCD Monitor
User Manual 41
3.2 OSD Menu Navigation
R2AP Panel Control Board Using the LCD Monitor
User Manual 42
3.2.1 Display
OSD Icon Sub menu Settings Note
BRIGHTNESS slider bar
Adjusts the overall image and background brightness. Press “ ” or “ ” to adjust.
CONTRAST slider bar
Adjusts the image brightness in relationship to the background. Press“ ” or “ ” to
adjust.
SHARPNESS slider bar
Adjusts the crispness of the image. Press“ ” or “ ” to adjust.
ADC BRIGHTNESS
*VGA CHANNEL ONLY slider bar
Adjusts the ADC brightness. Press“ ” or “ ” to adjust.
TEMPERATURE USER/ sRGB/ 6500K/ 9300K
Adjusts the color temperature of the entire screen. A low color temperature will
make the screen reddish. A high color temperature will make the screen bluish.
COLOR CONTROL
R slider bar
G slider bar
B slider bar
Adjusts the levels of the Red, Green, Blue. Press“ ” or “ ” to adjust.
GAMMA SELECTION
OFF
1.8
2.2
Select a display gamma value for best picture quality.
SCHEME
USER
Standard
GAME
SPORT
Movie
Photo
Select scheme for different default setting combination.
HUE slider bar
Saturation slider bar
Region 1P
1/2P,2/2P,1+2/2P
R2AP Panel Control Board Using the LCD Monitor
User Manual 43
1/4P,2+3+4/4P
2/4P, 1+3+4/4P
3/4P, 1+2+4/4P
4/4P,1+2+3/4P,1+2+3+4/4P
3.2.2 Adjust
Adjust
Auto Adjust
*VGA CHANNEL ONLY Yes/No
Automatically adjusts screen size, H position, V position, Clock, Clock Phase
AUTO Setting
*VGA CHANNEL ONLY OFF/ON
H Position, V Position and Clock Phase are adjusted automatically upon power on.
H POSITION
*VGA CHANNEL ONLY slider bar
Controls the horizontal position of the image within the Display area of the LCD.
Press + to move right. Press - to move left.
V POSITION
*VGA CHANNEL ONLY slider bar
Controls the vertical position of the image within the Display area of the LCD.
Press + to move up. Press - to move down.
CLOCK
*VGA CHANNEL ONLY slider bar
Press + to expand the width of the image on the right of the screen.
Press - to narrow the width of the image on the left.
PHASE
*VGA CHANNEL ONLY slider bar
Adjusts the visual “noise” on the image.
WHITE BALANCE
*VGA CHANNEL ONLY YES/OFF
Perform the white balance
R2AP Panel Control Board Using the LCD Monitor
User Manual 44
3.2.3 Audio
`
VOLUME slider bar
Adjusts the Volume. Press“ ” or “ ” to adjust.
MUTE ON/OFF
Audio Source Analog/1P/2P/3P/4P
3.2.4 Multi-Display
Display Mode
1P
1/2P Right Left
1/2P Up down
PIP
4P
Choose the Display Mode for 1P , 2P , 4P
Display source Select 1 2 3 4
Auto scan
VGA
DVI
HDMI 2.0
HDMI 1.4
DP
Choose the channel of Display source
2P LR Ratio
Ratio 0
Ratio 1
Ratio 2
Ratio 3
Ratio 4
PIP Size slider bar
Adjust the Picture-in-Picture( PIP) Size
PIP Position Horizontal
Vertical
Determines where the PIP appears on the screen.
Multi Display SWAP YES/NO
R2AP Panel Control Board Using the LCD Monitor
User Manual 45
3.2.5 OSD
OSD TURN OFF slider bar
Turns off the OSD after a period of inactivity. The preset choices are 10-60 seconds.
OSD POSITION Horizontal - slider bar
Vertical - slider bar
Determines the location where the OSD appears on the screen.
OSD TRANSPARENCY slider bar
Adjusts the transparency level of OSD
OSD Rotated
@OFF
@90
@270
Set to rotate the OSD menu
MONITOR INFORMATION
Version
Input 1 Source
Resolution
Input 2 Source
Resolution
Input 3 Source
Resolution
Input 4 Source
Resolution
Shows BIOS version & resolution info.
R2AP Panel Control Board Using the LCD Monitor
User Manual 46
3.2.6 Advanced
Scaling
Full Screen
16:9
4:3
5:4
1:1
Adjust the image scaling setting
Flip
ROTATE 0
ROTATE 90
ROTATE 0 180
ROTATE 0 270
Up down
Left Right
Scan Type Under Scan
Over Scan
Choose the scan type
Color Format RGB
YUV
Choose the format of color composition
Scheme RED HUE - slider bar
Saturation - slider bar
Scheme Green HUE - slider bar
Saturation - slider bar
Scheme Blue HUE - slider bar
Saturation - slider bar
Scheme Yellow HUE - slider bar
Saturation - slider bar
Scheme Magenta HUE - slider bar
Saturation - slider bar
Scheme Cyan HUE - slider bar
Saturation - slider bar
Brightness Min 0 to 10 Stratum
Factory rest Yes/No
R2AP Panel Control Board Using the LCD Monitor
User Manual 47
Resets OSD options back to factory settings EXCEPT FOR: CHANGE SECURITY
PASSWORD and SECURITY PASSWORD.
R2AP Panel Control Board Troubleshooting
User Manual 48
Troubleshooting This chapter contains troubleshooting information.
Check this guide before calling for repairs.
R2AP Panel Control Board Troubleshooting
User Manual 49
Chapter 4 Troubleshooting
If your monitor fails to operate correctly, check the following chart for possible
solution before calling for repairs:
Condition Check Point
1. The picture does not
appear
Check if the signal cable is firmly seated in the socket.
Check if the Power is ON at the computer
Check if the brightness control is at the appropriate position,
not at the minimum.
2. The screen is not
synchronized
Check if the signal cable is firmly seated in the socket.
Check if the output level matches the input level of your
computer.
Make sure the signal timings of the computer system are
within the specification of the monitor.
If your computer was working with a CRT monitor, you
should check the current signal timing and turn off your
computer before you connect the VGA Cable to this monitor.
3. The position of the
screen is not in the
center
Adjust the H-position, and V-position, or Perform the Auto
adjustment.
4. The screen is too
bright (too dark).
Check if the brightness or contrast control is at the
appropriate position, not at the Maximum (Minimum).
5. The screen is shaking
or waving
Perform the Auto adjustment.
Moving all objects which emit a magnetic field such as motor
or transformer, away from the monitor.
Check if the specific voltage is applied.
Check if the signal timing of the computer system is within
the specification of monitor.
6. VGA signal got noise
when using PIP
function
Change PIP mode again.
*If you are unable to correct the fault by using this chart, stop using your monitor and
contact your distributor or dealer for further assistance
R2AP Panel Control Board Appendices
User Manual 50
Supported Modes This section includes supported modes. The
choice of supported modes depends on the
monitor native resolution.
Appendix
R2AP Panel Control Board Appendices
User Manual 51
Appendix A Supported Modes
The choice of supported modes depends on the monitor native resolution.
DVI
No. Resolution Frequency
(Hz)
No. Resolution Frequency
(Hz)
1 640x350 70 21 1024x768 85
2 640x350 85 22 1280x768 60
3 640x400 56 23 1280x960 60
4 640x400 70 24 1280x960 85
7 640x480 75 25 1280x1024 60
8 640x480 80 26 1280x1024 60
9 720x350 70 27 1280x1024 67
10 720x400 70 28 1280x1024 70
11 720x400 85 29 1280x1024 72
12 800x600 56 30 1280x1024 75
13 800x600 60 31 1280x1024 85
14 800x600 72 32 1600x1200 60
15 800x600 75 33 1920x1200 60
16 800x600 85 34 1366x768 60
17 1024x768 60 35 1920x1080 60
18
1024x768 70
36 2560x1440
(DVI dual
link only)
60
19
1024x768 72
37 2560x1600
(DVI dual
link only)
60
20
1024x768 75
38 3840 x
2160
(DVI dual
link only)
R2AP Panel Control Board Appendices
User Manual 52
VGA
No. Resolution Frequency (Hz)
1 640x480 67
2 640x480 72
3 640x480 75
4 640x480 80
5 720x400 70
6 800x600 56
7 800x600 60
8 800x600 72
9 800x600 75
10 1024x768 60
11 1024x768 70
12 1024x768 72
13 1024x768 75
14 1024x768 75
15 1280x1024 60
16 1280x1024 75
17* 1600x1200 60
18* 1680x1050 60
19* 1920x1200 60
20* 1366x768 60
21* 1920x1080 60
R2AP Panel Control Board Appendices
User Manual 53
HDMI 1.4
No. Resolution Frequency
(Hz)
1 640x480 60
2 640x480 72
3 640x480 75
4 800x600 60
7 800x600 72
8 800x600 75
9 1024x768 60
10 1024x768 70
11 1024x768 75
12 1280x768 60
13 1280x1024 60
14 1280x1024 75
15 1366x768 60
16 1400x1050 60
17 1440x900 60
18 1600x900 60
19 1600x1200 60
20 1680x1050 60
21 1920x1080 60
22 1920x1200 60
24 2560x1600 60
25 3840x2160 30
R2AP Panel Control Board Appendices
User Manual 54
HDMI 2.0
No. Resolution Frequency
(Hz)
1 640x480 60
2 640x480 72
3 640x480 75
4 800x600 60
7 800x600 72
8 800x600 75
9 1024x768 60
10 1024x768 70
11 1024x768 75
12 1280x768 60
13 1280x1024 60
14 1280x1024 75
15 1366x768 60
16 1400x1050 60
17 1440x900 60
18 1600x900 60
19 1600x1200 60
20 1680x1050 60
21 1920x1080 60
22 1920x1200 60
24 2560x1600 60
25 3840x2160 60
26 4096x2160 60
R2AP Panel Control Board Appendices
User Manual 55
Display port 1.2
No. Resolution Frequency
(Hz)
1 640x480 60
2 640x480 72
3 640x480 75
4 800x600 60
7 800x600 72
8 800x600 75
9 1024x768 60
10 1024x768 70
11 1024x768 75
12 1280x768 60
13 1280x1024 60
14 1280x1024 75
15 1366x768 60
16 1400x1050 60
17 1440x900 60
18 1600x900 60
19 1600x1200 60
20 1680x1050 60
21 1920x1080 60
22 1920x1200 60
24 2560x1600 60
25 3840x2160 30
26 3840x2160 60
27 4096x2160 60
R2AP Panel Control Board Appendices
User Manual 56
Remote Control Set Command This section includes remote control set
command.
Appendix
R2AP Panel Control Board Appendices
User Manual 57
Appendix C Remote Control Set Command
Name Length Value Comment
Message Variable
Checksum 1 2's complement of
sum of Length and
Message
byte chksum = 0;
for ( i = 0; i<buffer_size; ++i )
chksum += buf[i];
chksum = ~chksum + 1;
No Function Length Command Index Value Checksum(*1) Remark
1 Auto 0x05 0x40 0x01 0=Auto 0xBA=Auto
2 Recall 0x05 0x40 0x02 0=Recall 0xB9=Recall
3 White Balance 0x05 0x40 0x03 0=White
Balance
0xB8=White
Balance
4 1P Input
Source 0x05 0x40 0x04
0x00=VGA
0x01=DVI
0x07=HDMI 2.0
0x08=DP
0x17=HDMI 1.4
0xB7=VGA
0xB6=DVI
0xB0=HDMI 2.0
0xAF=DP
0xA0= HDMI 1.4
5 2P Input
Source 0x05 0x40 0x05
0x00=VGA
0x01=DVI
0x07=HDMI 2.0
0x08=DP
0x17=HDMI 1.4
0xB6=VGA
0xB5=DVI
0xAF=HDMI 2.0
0xAE=DP
0x9F= HDMI 1.4
6 3P Input
Source 0x05 0x40 0x06
0x00=VGA
0x01=DVI
0x07=HDMI 2.0
0x08=DP
0x17=HDMI 1.4
0xB5=VGA
0xB4=DVI
0xAE=HDMI 2.0
0xAD=DP
0x9E= HDMI 1.4
7 4P Input
Source 0x05 0x40 0x07
0x00=VGA
0x01=DVI
0x07=HDMI 2.0
0x08=DP
0x17=HDMI 1.4
0xB4=VGA
0xB3=DVI
0xAD=HDMI 2.0
0xAC=DP
0x9D= HDMI 1.4
8 Display Mode 0x05 0x40 0x08 0x00 Mode 1P
0x01 Mode 2P
0xB3 Mode 1P
0xB2 Mode 2P
R2AP Panel Control Board Appendices
User Manual 58
(L/R)
0x02 Mode 2P
(T/B)
0x03 Mode 2P
(M/S)
0x04 Mode 4P
(L/R)
0xB1 Mode 2P
(T/B)
0xB0 Mode 2P
(M/S)
0xAF Mode 4P
9 Region 0x05 0x40 0x09
0x00 1P
0x01 2P LR Left
0x02 2P LR
Right
0x03 2P LR Full
0x04 2P TB Top
0x05 2P TB
Button
0x06 2P TB Full
0x07 2P PIP
Main
0x08 2P PIP
Sub
0x09 2P PIP
Full
0x0A 4P LT
Inside
0x0B 4P LT
Outside
0x0C 4P LB
Inside
0x0D 4P LB
Outside
0x0E 4P RT
Inside
0x0F 4P RT
Outside
0x10 4P RB
Inside
0x11 4P RB
Outside
0x12 4P Full
0xB2 1P
0xB1 2P LR Left
0xB0 2P LR Right
0xAF 2P LR Full
0xAE 2P TB Top
0xAD 2P TB
Button
0xAC 2P TB Full
0xAB 2P PIP Main
0xAA 2P PIP Sub
0xA9 2P PIP Full
0xA8 4P LT Inside
0xA7 4P LT
Outside
0xA6 4P LB Inside
0xA5 4P LB
Outside
0xA4 4P RT Inside
0xA3 4P RT
Outside
0xA2 4P RB Inside
0xA1 4P RB
Outside
0xA0 4P Full
R2AP Panel Control Board Appendices
User Manual 59
10 Brightness 0x05 0x40 0x10 0x00~0x64 0xAB=0 ~
0x47=100
11 Contrast 0x05 0x40 0x11 0x00~0x64 0xAA=0 ~
0x46=100
Region
12 Hue 0x05 0x40 0x12 0x00~0x64 0xA9=0 ~
0x45=100
Region
13 Saturation 0x05 0x40 0x13 0x00~0x64 0xA8=0 ~
0x44=100
Region
14 ADC
Brightness 0x05 0x40 0x14 0x00~0x64
0xA7=0 ~
0x43=100
Region
15 Sharpness 0x05 0x40 0x15 0x00~0x04 0xA6=0 ~ 0xA2=4 Region
16 Gamma 0x05 0x40 0x31
0=Native
1=Gamma 1.8
2=Gamma 2.2
0x8A= Native
0x89=Gamma 1.8
0x88=Gamma 2.2
Region
17 Color Temp 0x05 0x40 0x32
0=user
1=9300K
2=6500K
3=sRBG
0x89=User
0x88=9300K
0x87=6500K
0x86=sRGB
Region
18 Color-R 0x05 0x40 0x33 0x00-0x64 0x88=0 ~
0x24=100
Region
19 Color-G 0x05 0x40 0x34 0x00-0x64 0x87=0 ~
0x23=100
Region
20 Color-B 0x05 0x40 0x35 0x00-0x64 0x86=0 ~
0x22=100
Region
21 SCHEME 0x05 0x40 0x36
0=Standard
1=GAME
2=MOVIE
3=PHOTO
4=VIVID
5=USER
0x85=Standard
0x84=GAME
0x83=MOVIE
0x82=PHOTO
0x81=VIVID
0x80=USER
Region
22 Volume 0x05 0x40 0x50 0x00~0x64 0x6B=0~0x07=100
23 Mute 0x05 0x40 0x54 0=OFF
1=ON
0x67=OFF
0x66=ON
24 Audio Source 0x05 0x40 0x55
0=Analog
1=1P
2=2P
3=3P
4=4P
0x66=Analog
0x65=1P
0x64=2P
0x63=3P
0x62=4P
R2AP Panel Control Board Appendices
User Manual 60
25 LR RATIO 0x05 0x40 0x70
0=RATIO 0
1=RATIO 0
2=RATIO 0
3=RATIO 0
4=RATIO 0
0x4B=RATIO 0
0x4A=RATIO 0
0x49=RATIO 0
0x48=RATIO 0
0x47=RATIO 0
26 PIP SIZE 0x05 0x40 0x71 0x00~0x0A 0x4A=0~0x40=10
27 FLIP 0x05 0x40 0x80
0=ROTATE 0
1=ROTATE 90
2=ROTATE 180
3=ROTATE 270
4=H MIRROR
5=V MIRROR
0x3B=ROTATE 0
0x3A=ROTATE 90
0x39=ROTATE 180
0x38=ROTATE 270
0x37=H MIRROR
0x36=V MIRROR
28 SCALING 0x05 0x40 0x81
0=FULL
1=16:9
2=4:3
3=5:4
4=1:1
0x3A=FULL
0x39 =16:9
0x38 =4:3
0x37 =5:4
0x36 =1:1
Region
29 SCHEME Red
Hue 0x05 0x40 0x82 0x00~0x64 0x39=0~0xD5=100
Region
30 SCHEME Red
Sat 0x05 0x40 0x83 0x00~0x64 0x38=0~0xD4=100
Region
31 SCHEME
Green Hue 0x05 0x40 0x84 0x00~0x64 0x37=0~0xD3=100
Region
32 SCHEME
Green Sat 0x05 0x40 0x85 0x00~0x64 0x36=0~0xD2=100
Region
33 SCHEME Blue
Hue 0x05 0x40 0x86 0x00~0x64 0x35=0~0xD1=100
Region
34 SCHEME Blue
Sat 0x05 0x40 0x87 0x00~0x64 0x34=0~0xD0=100
Region
35 SCHEME
Yellow Hue 0x05 0x40 0x88 0x00~0x64 0x33=0~0xCF=100
Region
36 SCHEME
Yellow Sat 0x05 0x40 0x89 0x00~0x64 0x32=0~0xCE=100
Region
37 SCHEME
Magenta Hue 0x05 0x40 0x8A 0x00~0x64 0x31=0~0xCD=100
Region
38 SCHEME
Magenta Sat 0x05 0x40 0x8B 0x00~0x64 0x30=0~0xCC=100
Region
39 SCHEME Cyan 0x05 0x40 0x8C 0x00~0x64 0x2F=0~0xCB=100 Region
R2AP Panel Control Board Appendices
User Manual 61
Hue
40 SCHEME Cyan
Sat 0x05 0x40 0x8D 0x00~0x64 0x2E=0~0xCA=100
Region
R2AP Panel Control Board Appendices
User Manual 62
Remote Control Get Command This section includes remote control get
command.
Appendix
R2AP Panel Control Board Appendices
User Manual 63
Appendix D Remote Control Get Command
Name Length Value Comment
Message variable
Checksum 1 2’s complement of sum of
Length and Message
byte chksum = 0;
for ( I = 0; I
<buffer_size; ++I )
chksum += buf[i];
chksum = ~chksum
+ 1;
Command(Tx) Acknowledgement(Rx)
Function Length Command Index Checksu
m
Leng
th
Inde
x Value Checksum
1P Input
Source 0x04 0x30 0x04 0xC8 0x04 0x04
0x00=VGA
0x01=DVI
0x07=HD
MI 2.0
0x08=DP
0x17=HD
MI 1.4
0xF8=VGA
0xF7=DVI
0xF1=HDMI 2.0
0xF0=DP
0xE1=HDMI 1.4
2P Input
Source 0x04 0x30 0x05 0xC7 0x04 0x05
0x00=VGA
0x01=DVI
0x07=HD
MI 2.0
0x08=DP
0x17=HD
MI 1.4
0xF7=VGA
0xF6=DVI
0xF0=HDMI 2.0
0xEF=DP
0xE0=HDMI 1.4
3P Input
Source 0x04 0x30 0x06 0xC6 0x04 0x06
0x00=VGA
0x01=DVI
0x07=HD
MI 2.0
0x08=DP
0x17=HD
MI 1.4
0xF6=VGA
0xF5=DVI
0xEF=HDMI 2.0
0xEE=DP
0xDF=HDMI 1.4
4P Input 0x04 0x30 0x07 0xC5 0x04 0x07 0x00=VGA 0xF5=VGA
R2AP Panel Control Board Appendices
User Manual 64
Source 0x01=DVI
0x07=HD
MI 2.0
0x08=DP
0x17=HD
MI 1.4
0xF4=DVI
0xEE=HDMI 2.0
0xED=DP
0xDE=HDMI 1.4
Display Mode 0x04 0x30 0x08 0xC4 0x04 0x08
0x00
Mode 1P
0x01
Mode 2P
(L/R)
0x02
Mode 2P
(T/B)
0x03
Mode 2P
(M/S)
0x04
Mode 4P
0xF4 Mode 1P
0xF3 Mode 2P
(L/R)
0xF2 Mode 2P
(T/B)
0xF1 Mode 2P
(M/S)
0xF0 Mode 4P
Region 0x04 0x30 0x09 0xC3 0x04 0x09
0x00 1P
0x01 2P
LR Left
0x02 2P
LR Right
0x03 2P
LR Full
0x04 2P
TB Top
0x05 2P
TB Button
0x06 2P
TB Full
0x07 2P
PIP Main
0x08 2P
PIP Sub
0x09 2P
PIP Full
0x00 1P
0x01 2P LR Left
0x02 2P LR
Right
0x03 2P LR Full
0x04 2P TB Top
0x05 2P TB
Button
0x06 2P TB Full
0x07 2P PIP
Main
0x08 2P PIP
Sub
0x09 2P PIP Full
0x0A 4P LT
Inside
0x0B 4P LT
Outside
0x0C 4P LB
R2AP Panel Control Board Appendices
User Manual 65
0x0A 4P LT
Inside
0x0B 4P LT
Outside
0x0C 4P
LB Inside
0x0D 4P
LB
Outside
0x0E 4P
RT Inside
0x0F 4P
RT
Outside
0x10 4P
RB Inside
0x11 4P
RB
Outside
0x12 4P
Full
Inside
0x0D 4P LB
Outside
0x0E 4P RT
Inside
0x0F 4P RT
Outside
0x10 4P RB
Inside
0x11 4P RB
Outside
0x12 4P Full
Brightness 0x04 0x30 0x10 0xBC 0x04 0x10 0x00-0x64 0xEC=0 ~
0x88=100
Contrast 0x04 0x30 0x11 0xBB 0x04 0x11 0x00-0x64 0xEB=0 ~
0x87=100
Hue 0x04 0x30 0x12 0xBA 0x04 0x12 0x00-0x64 0xEA=0 ~
0x86=100
Saturation 0x04 0x30 0x13 0xB9 0x04 0x13 0x00-0x64 0xE9=0 ~
0x85=100
ADC
Brightness 0x04 0x30 0x14 0xB8 0x04 0x14 0x00-0x64
0xE8=0 ~
0x84=100
Sharpness 0x04 0x30 0x15 0xB7 0x04 0x15 0x00-0x04 0xE7=0 ~
0xE3=4
Gamma 0x04 0x30 0x31 0x9B 0x04 0x31
0=Native
1=Gamma
1.8
2=Gamma
2.2
0xCB= Native
0xCA= Gamma
1.8 0xC9=
Gamma 2.2
R2AP Panel Control Board Appendices
User Manual 66
Color Temp 0x04 0x30 0x32 0x9A 0x04 0x32
0=user
1=9300K
2=6500K
3=sRBG
0xCA=user
0xC9=9300k
0xC8=6500k
0xC7=sRBG
Color-R 0x04 0x30 0x33 0x99 0x04 0x33 0x00-0x64 0xC9=0 ~
0x65=100
Color-G 0x04 0x30 0x34 0x98 0x04 0x34 0x00-0x64 0xC8=0 ~
0x64=100
Color-B 0x04 0x30 0x35 0x97 0x04 0x35 0x00-0x64 0xC7=0 ~
0x63=100
SCHEME 0x04 0x30 0x36 0x96 0x04 0x36
0=Standar
d
1=GAME
2=MOVIE
3=PHOTO
4=VIVID
5=USER
0xC6=Standard
0xC5=GAME
0xC4=MOVIE
0xC3=PHOTO
0xC2=VIVID
0xC1=USER
Volume 0x04 0x30 0x50 0x7C 0x04
0x50 0x00-0x64 0xAC=0 ~
0x48=100
Mute 0x04 0x30 0x54 0x78 0x04 0x54 0=OFF
1=ON
0xA8=OFF
0xA7 =ON
Audio Source 0x04 0x30 0x55 0x77 0x04 0x55
0=Analog
1=1P
2=2P
3=3P
4=4P
0xA7=Analog
0xA6=1P
0xA5=2P
0xA4=3P
0xA3=4P
LR RATIO 0x04 0x30 0x70 0x5C 0x04 0x70
0=RATIO 0
1=RATIO 0
2=RATIO 0
3=RATIO 0
4=RATIO 0
0x8C=RATIO 0
0x8B=RATIO 0
0x8A=RATIO 0
0x89=RATIO 0
0x88=RATIO 0
PIP SIZE 0x04 0x30 0x71 0x5B 0x04 0x71 0x00~0x0
A
0x8B=0~0x81=
10
FLIP 0x04 0x30 0x80 0x4C 0x04 0x80
0=ROTATE
0
1=ROTATE
90
2=ROTATE
0x7C=ROTATE 0
0x7B=ROTATE
90
0x7A=ROTATE
180
R2AP Panel Control Board Appendices
User Manual 67
180
3=ROTATE
270
4=H
MIRROR
5=V
MIRROR
0x79=ROTATE
270
0x78=H
MIRROR
0x77=V
MIRROR
SCALING 0x04 0x30 0x81 0x4B 0x04 0x81
0=FULL
1=16:9
2=4:3
3=5:4
4=1:1
0x7B=FULL
0x7A =16:9
0x79 =4:3
0x78 =5:4
0x77 =1:1
SCHEME Red
Hue 0x04 0x30 0x82 0x4A
0x04 0x82
0x00~0x6
4
0x7A=0~0x16=
100
SCHEME Red
Sat 0x04 0x30 0x83 0x49
0x04 0x83
0x00~0x6
4
0x79=0~0x15=1
00
SCHEME
Green Hue 0x04 0x30 0x84 0x48
0x04 0x84
0x00~0x6
4
0x78=0~0x14=1
00
SCHEME
Green Sat 0x04 0x30 0x85 0x47
0x04 0x85
0x00~0x6
4
0x77=0~0x13=1
00
SCHEME Blue
Hue 0x04 0x30 0x86 0x46
0x04 0x86
0x00~0x6
4
0x76=0~0x12=1
00
SCHEME Blue
Sat 0x04 0x30 0x87 0x45
0x04 0x87
0x00~0x6
4
0x75=0~0x11=1
00
SCHEME
Yellow Hue 0x04 0x30 0x88 0x44
0x04 0x88
0x00~0x6
4
0x74=0~0x10=1
00
SCHEME
Yellow Sat 0x04 0x30 0x89 0x43
0x04 0x89
0x00~0x6
4
0x73=0~0x0F=1
00
SCHEME
Magenta Hue 0x04 0x30 0x8A 0x42
0x04 0x8A
0x00~0x6
4
0x72=0~0x0E=1
00
SCHEME
Magenta Sat 0x04 0x30 0x8B 0x41
0x04 0x8B
0x00~0x6
4
0x71=0~0x0D=
100
SCHEME
Cyan Hue 0x04 0x30 0x8C 0x40
0x04 0x8C
0x00~0x6
4
0x70=0~0x0C=
100
SCHEME
Cyan Sat 0x04 0x30 0x8D 0x3F
0x04 0x8D
0x00~0x6
4
0x6F=0~0x0B=1
00
R2AP Panel Control Board Appendices
User Manual 68
Electrical Characteristics This section includes important information on
power input, input/analog input voltage and
power consumption in different modes.
Appendix
R2AP Panel Control Board Appendices
User Manual 69
Appendix E Electrical Characteristics
Power Input
Parameter Symbol Min. Typ. Max. Unit. Remark
Input Voltage Vin +10.8
+13.2
+12
+24V
+13.2+
+26.4
VDC Note 1
Analog Input Voltage VCVS - 1.0 1.1 Vp-p Note 2
VRGB - 0.7 1.1 Vp-p Note 2,3
Digital Input
Signal
H-level Vih 2.75 - 5.0 VDC Note 4
L-level Vil 0 - 1.0 VDC
Note 1: Power input.
Note 2: Composite and standard RGB video signal input impedance: 75Ω.
Note 3: RIN, GIN, BIN terminals (RGB video signals).
Note 4: HS, VS, DDCSDA, DDCSCL.
Power Consumption
Parameter Min. Typ. Max. Unit. Remark
Operating Mode - 3.6 4 Watt
Standby Mode - 2.5 - Watt
Off Mode - - 0.2 Watt
Recommended