View
170
Download
1
Category
Tags:
Preview:
Citation preview
Quic
ke imple
ments
22 | Quicke Dimension
A
b
c
THE LOADER CANNOT FUNCTION WITHOUT IMPLEMENTS. Every day, all year round, Quicke loaders carry out work duties for many different users, from farmers to contractors. Without good-quality, versatile implements, the loaders would not be as useful. This is why we invest considerable resources in devel-oping implements that do the Quicke loaders justice. This investment and effort has resulted in us also being the world’s largest producer of implements for front loaders.
Implement hooks for various loaders
A: EuroEuro implement hooks (Ø 40 mm) are the most widely used hook type.
As a result, owners of many different loader makes can also benefit from our
large implement range.
B: SMS (Svensk Maskin Standard) These implement hooks (Ø 60 mm) are primarily adapted for Trima’s front loaders.
If a Quicke loader is equipped with a Combi implement subframe Euro/SMS,
it can work with both Euro and SMS implements.
C: Quicke type 3 These implement hooks (Ø 25 mm) have only been used on older
Ålö loaders (up to 1992) with the Quicke type 3 toolcarrier. If a new Quicke
loader is equipped with a Combi implement subframe Euro/Type 3,
it can work with both Euro implements and with the older type 3 implements.
We can also provide a selection of adapters for other hook systems.
Quicke Dimension | 23
THE LOADER CANNOT FUNCTION WITHOUT IMPLEMENTS.
Quadrogrip®
bale implement Flexibal®
Flexibal
weight 195 kg
Bale size max. 180 cm
Bale support
weight 45 kg
Quadrogrip is the best implement on the market for handling wrapped square
and round bales. The implement arms are seated on 350 mm wide, extremely
stable sliding plates, which move along the main frame. When stacking, it is
possible to lock either the right or left arm, which makes for easier work. The
sliding rails are replaceable and made of high-quality polyethylene, which does
not require lubrication. These sliding surfaces are also vertical so that dirt can-
not become trapped. This results in reduced friction, almost silent arm move-
ments, minimal wear and a long service life.
Three implements in oneFlexibal is a strong and very versatile implement. The 125 mm thick, rotating steel tubes are mounted on two powerful
stone fork tines. The steel tubes are hydraulically adjustable sideways. When the bale is handled, the steel tubes roll care-
fully in under the bale. The tubes’ generous length and diameter distribute the pressure evenly over the bale. When straw
or hay bales are to be transported, the steel tubes can be dismantled quickly and easily. With the tubes removed, Flexibal
can also be used for pallet handling (max. 1,000 kg).
As an option Flexibal can be equipped with an adjustable bale support that is installed on the back of the implement.
This provides the potential to either handle larger bales or to stack bales on their ends.
Selecto F
ix – Easier implemen
t changes
Selecto F
ix – Easier implemen
t changes
Quadrogrip 200
Total width 235 cm
For bale size, min-max 60-200 cm
Arm length 130 cm
Weight 418 kg
24 | Quicke Dimension
Flexigrip™ Unigrip™
Grip, lift and turn the bale. Then transport it to the storage place, where stacking to at least the height of three bales is a simple matter.
Select the best equipmentSilaging in plastic bales can produce first-class silage.
However, the bottleneck in this process is often the
implement that has to handle and transport the
bales. It is therefore important to select a quality
product that can handle the bales in the right way. If
the implement is not good enough, it can break or
damages the bale plastic and the whole process stops,
expensive equipment and manpower are at a stand-
still and the quality of the silage is impaired.
Our implements are characterised by powerful
bearings in the arms, large implement areas so that
the pressure is distributed optimally and by the to-
tal absence of any sharp edges. We accept no com-
promises – the quality has to be the very best.
Unigrip 130 160
For bale sizes, min-max 90-130 cm 120-160 cm
weight 200 kg 240 kg
Storing the bales upright on top of each other reduces the risk of air and
moisture penetrating into the bales.
The implement arms are housed in powerful hinged points with replace-
able bushings. Both the right or left arm can be locked Independently, but
there is still some mobility, making it possible to stack the bales tightly
without damaging the plastic. In addition, the implement arms are designed
so that it is easy to reverse out from the bale, and this is also an advantage
when the bales are to be stacked tightly.
The uniquely curved, rounded shape together with the 90 mm thick
tubes contribute greatly to the very careful handling of both vertical and
horizontal bales. Note in particular the long, curved tubes, curved in one
piece with no sharp edges or welded joints. The upper tube extension is a
Quicke speciality that provides significantly better support when the bales
are handled horizontally.
Unigrip has a tested and proven design and a low net weight. It carries
out the same tasks as Flexigrip. The choice between these two implements
depends on the individual user’s work routines. Unigrip is also well suited
for smaller square bales (80 x 80 – 130-160 cm).
The implement arms distribute the pressure evenly over a large area,
and this ensures careful handling of the bales. The tubes on the arms have
a powerfully dimensioned diameter. Unigrip also has a large tube diameter
and no sharp edges, so that the plastic around the bale is not damaged.
Flexigrip 160 200For bale sizes, min.max. 120-160 cm 150-200 cm
Weight 242 kg 262 kg
Selecto F
ix – Easier implemen
t changes
Selecto F
ix – Easier implemen
t changes
bale implement
Quicke Dimension | 25
Selecto F
ix – Easier implemen
t changes
Silosplit®
DB 2115 Weight 200 kg
Increased lifting height 115 cm
Number of bales 4-5
[bale height 120 cm]
Bale size max. 130 cm
For safe handling of 2-4 bales.The bales are securely held between the tines and the upper section. In other words,
there is no risk of dropping the bales during transport or stacking. The mast is both
telescopic and hydraulic. The height of the upper section can vary from 95 cm to
195 cm.
Equip your front loader with 115 cm extra lifting height, so that you
can stack the bales even higher. The DB 2115 is an excellent imple-
ment, particularly for those who require
a high lifting height with short, manoeu-
vrable loaders.
DB 4000
DB 4000 Weight 190 kg
Number of tines 4
DB 2115
Selecto F
ix – Easier implemen
t changes
Silosplit m hd weight 85 kg 110 kg
Width 120 cm 120 cm
Length 140 cm 170 cm
PATENT
Split the bale with ease and cheaplyUntil now, splitting bales has entailed hard work or considerable expense. If you have a loader with
dual-action lifting cylinders, you can solve the problem thanks to Silosplit.
Silosplit can both transport and split bales. When you have placed the bale where it is to be split,
you place the blade across the top of the bale and press down. Both straw and silage bales fall apart in
two pieces, simply and smoothly without complicated extra hydraulics. It is then easy to handle the
material. Silosplit is supplied with an easy-to-use blade guard to provide protection from the sharp
cutting edge.
Silosplit is naturally patented.
26 | Quicke Dimension
Bale implement
Square Bale Fork – Safety
Square Bale Fork – standard
The bale spike is particularly well suited to handling round bales. The
longer tine ensures safe transport of the bale. The shorter tine prevents
the bale from wobbling and rotating during stacking.
The Square Bale Fork is a simple, robust implement for both round
and square bales. The tines in the box section can be installed with
a separation of 80 or 130 cm. As an optional extra, the fork can be
supplied with a U-shaped vertical rear
extension, which helps to support the
top bale.
The Square Bale Fork’sfolding box section is a new and valuable safety detail.
Firstly you can lock the tines in the upright position, increasing safety during transport,
particularly on public roads. Secondly you get more efficient and safer handling.
When unloading, the bales are pushed into place by the main frame. If unloading takes
place at full height, the top bale is pushed into place with the aid of the upper section
of the implement, without the long tines being pressed down into the bales. As a result,
there is no risk of the bales falling back when you reverse.
The Square Bale Fork can be supplied with two different frames. The 190 cm frame
is suitable for long, large bales. The 140 cm frame is
supplied with two tines as standard, although this
number can be increased to a total of five.
As optional extra equipment, the Square Bale Forks
can be supplied with a back extension (for handling
more bales) or a bag lifter (for handling large bags).
Square Bale Fork Bale spike
Bale spike
Weight 60 kg
Width 115 cm
Tine length 125 cm
Square Bale Fork – Safety 140 190
Weight 133 kg 168 kg
Width 140 cm 190 cm
Number of tines, standard 2 5
Tine length 125 cm 125 cm
Square Bale Fork - standard Weight 78 kg
Width 140 cm
number of tines, standard 2
Tine length 82 cm or
125 cm
Extension Weight 42 kg
7
28 | Quicke Dimension
Silograb®
silage Multibenne™
The perfect all-round implementIf you have a diet feeder that is to be loaded with various feeds, Multibenne is the best
choice. The wishes and requirements to which we have paid particular attention are that:
It should be perfectly suited for its purpose – namely silage handling. The side
ends are therefore tapered so that they can be inserted into the silage more easily.
When the implement is tipped backwards, the high ends come into play, so that loose
material is not lost. A relatively short base makes it easier to fill the entire bucket, all
the way in to the back. The centre of gravity thereby moves closer to the tractor, and
when unloading into high-sided vehicles, the bucket tip does not protrude as far into
the vehicle. The closed bottom and the close tine location results in reduced spillage.
With the closed bucket bottom, you can always completely gather up the material.
Multibenne, which is designed according to the same principles as Silograb, can
handle many different types of fodder, as well as manure. As a result, it is not neces-
sary to switch between implements when feeding.
Silograb is an extremely versatile implement. The close tine distribution almost eliminates the spillage of silage.
The tines are mounted in a specially hardened box section (approximately six times larger than standard profiles),
which does not turn or deform under load. The tines follow a circular movement through the material, which pro-
duces the cleanest cut, the least power consumption and the longest service life for the tines. In addition the material
is pressed against the back of the implement when the tines are lowered, and this means that the silage remains in
place, even when driving over uneven terrain.
All models have two hydraulic cylinders. On the large models, the cylinders are 15% larger. The 210 to 250 models
are supplied with a mesh construction in the upper section.
Silograb 130 150 170 190 210 230 250 Weight 250 kg 270 kg 300 kg 320 kg 355 kg 377 kg 405 kg
Width 130 cm 150 cm 170 cm 190 cm 210 cm 230 cm 250 cm
Volume 0.69 m3 0.79 m3 0.90 m3 1.01 m3 1.11 m3 1.22 m3 1.33 m3
Depth 85 cm 85 cm 85 cm 85 cm 85 cm 85 cm 85 cm Number of tines
in the fork 7+7 8+8 9+9 10+10 11+11 12+12 13+13
Multibenne 130 150 170 190 210 230 250 Weight 280 kg 304 kg 360 kg 386 kg 423 kg 447 kg 477 kg
Width 130 cm 150 cm 170 cm 190 cm 210 cm 230 cm 250 cm
Volume 0.66 m3 0.76 m3 0.86 m3 0.96 m3 1.07 m3 1.17 m3 1.27 m3
Depth 80 cm 80 cm 80 cm 80 cm 80 cm 80 cm 80 cm
Number of tines in the fork 7 8 9 10 11 12 13
Selecto F
ix – Easier implemen
t changes
Quicke Dimension | 29
Multigrab hd™ Manure forkMaxi Grapple™
The bucket is based on the powerful, reinforced HD bucket. The grapple
arm is installed on the rear of the bucket, which also contributes to the im-
plement’s strength. The movable, profile-pressed upper section is supplied
with strong bearings, three-layer bushings and large pivot pins with stable
locking. The section with the powerful Hardox teeth is bolted in place. Stress
and torsion forces are thereby transmitted to the entire construction. The
teeth (version T) are simply bolted in place with a bolt in the bucket bottom.
The protective mesh means that loose material does not drop down onto the
tractor (optional extra).
Maxi Grapple is used particularly in the USA and Canada for handling
round bales (large opening of 2 m), loose hay, twigs and branches, loose si-
lage, manure and for general bucket work. Teeth, protective mesh and grap-
ple arm can easily be removed when only the bucket is to be used.
Multigrab HD is a very powerful implement. When filling silage, the bucket
tip is advanced towards the silo, the powerful upper arm is pressed down
through the silage and into the bucket. The special design of the teeth cre-
ates a block with a good cut surface. This reduces the admission of air and
heat generation in the silage. Thanks to its incredible strength, the Multi-
grab HD can also be used for many other demanding fork and bucket tasks.
Three advantages that make a lot of difference: Our manure forks are
equipped with a specially hardened box section that neither deforms nor
turns when working. The tines are installed before the implement is painted
– metal to metal. The tines are secured with a very high torque.
All in all, you get an implement with a longer service life.
Multigrab hd 160 180 200 Weight 460 kg 500 kg 560 kg
Width 160 cm 180 cm 200 cm
Volume 0.86 m3 1.00 m3 1.14 m3
Depth 80 cm 80 cm 80 cm
Maxi Grapple 210 210 t 240 Weight 605 kg 620 kg 640 kg
Width 210 cm 210 cm 240 cm
Depth 81 cm 81 cm 86 cm Teeth – 24 cm –
240 t 260 260 t Weight 655 kg 710 kg 730 kg
Width 240 cm 260 cm 260 cm
Depth 86 cm 86 cm 86 cm
Teeth 24 cm – 27 cm
Selecto F
ix – Easier implemen
t changes
Manure fork 130 150 170 Weight 123 kg 136 kg 152 kg
Width 130 cm 150 cm 170 cm
Depth 85 cm 85 cm 85 cm
Number of tines 7 8 9
190 230 Weight 165 kg 203 kg
Width 190 cm 230 cm
Depth 85 cm 85 cm
Number of tines 10 12
30 | Quicke Dimension
12
5
6
3
4
Buckets
We all know that today’s buckets are subjected to larger loads and more hours of operation than before. Both tractors and front loaders have been made larger and more powerful.
The buckets need to be wider and hold a larger volume. We have therefore cho-sen an even stronger and better grade of steel. In addition, we use profile-pressed and laser cut sheet-metal. This unifies the need for extra strength with the desire for an attractive design.
1. The buckets have a round bottom and a conical shape. Numerous small bends make the bucket strong and the conical design allows simple filling and complete emptying.
2. In order to achieve even greater torsional strength and stability, the wider buckets have been supplied with an extra, profile-pressed, double back plate (not on the L and LV models). With the aid of a special overlap design, the HV buckets now have a hole profile along the implement hooks, which makes these buckets stronger and more stable.
3. The upper edge of the bucket back is pressed in a U-profile. In this area on the HD buckets there is a further welded angle profile along the length of the bucket.
4. The ends have a profile extrusion that makes the sides even stronger (not on the L and LV models). At the bottom is a welded triangular wearing piece, which simultaneously stabilises the cutting edge. On the HD buckets, this wearing piece runs all the way up along the end side.
5. All buckets have extremely strong cutting edges (500 Brinell). Depending on bucket model and size, 12, 16 or 20 mm thick and 100, 150 or 200 mm wide cut-ting edges are used. Together with the parallel reinforcing bars, the bucket bot-tom consequently extremely strong, torsionally stable and hard-wearing.
6. The implement hooks also contribute to a strong construction. Note that both hooks and locking holes are located along a bend. Depending on bucket model and size, there may be a double profile inside the bucket.
A bucket is not just a bucketAll buckets are conical and are therefore easy to fill, as the material does not need to be pressed into the bucket. The conical, “hopper-shaped” design also allows rapid and complete emptying of the bucket.
No matter what your needs are or what demands you stipulate, you will be able to find your new bucket in our range. There are six different models and a total of 21 different variants. There is also a special, high tip bucket and a grading bucket.
The non-spill bucket
Non-drop designIt has been a natural objective to design and produce a bucket that does not
allow spillage. What’s the point of having a bucket with a large volume if it
cannot be properly filled, or if it spills material? Our buckets therefore have
laser-cut ends. As a result, it is possible to create a bucket design where the
rear edge and in particular the front edge are especially high. It is now pos-
sible to completely fill the bucket. You have complete control over the mate-
rial, and the bucket does not drop any material.
Quicke Dimension | 31
Series h 135h 160h Volume (heaped) 0.54 m3 0.65 m3
Width 135 cm 160 cm
Depth 81 cm 81 cm
Height 75 cm 75 cm
Cutting edge WxT 150/16 mm 150/16 mm
Weight 147 kg 166 kg
Series h 185h 210h 240h Volume (heaped) 0,72 m3 0,82 m3 0,95 m3
Width 185 cm 210 cm 240 cm
Depth 81 cm 81 cm 81 cm
Height 75 cm 75 cm 75 cm
Cutting edge WxT 150/16 mm 150/16 mm 150/20 mm
Weight 205 kg 252 kg 294 kg
Series ht 135ht 160ht Volume (heaped) 0.54 m3 0.65 m3
Width 135 cm 160 cm
Depth 81 cm 81 cm
Height 75 cm 75 cm
Cutting edge WxT 150/16 mm 150/16 mm
Number of teeth 6 7
Weight 152 kg 172 kg
Series ht 185ht 210ht Volume (heaped) 0.72 0.82
Width 185 cm 210 cm
Depth 81 cm 81 cm
Height 75 cm 75 cm
Cutting edge WxT 150/16 mm 150/16 mm
Number of teeth 8 9
Weight 211 kg 259 kg
Series hd 185hd 210hd Volume (heaped) 0,72 m3 0,82 m3
Width 185 cm 210 cm
Depth 81 cm 81 cm
Height 75 cm 75 cm
Cutting edge WxT 150/20 mm 150/20 mm
Weight 235 kg 285 kg
240hd 260hd Volume (heaped) 0.95 m3 1.03 m3
Width 240 cm 260 cm
Depth 86 cm 86 cm
Height 75 cm 75 cm
Cutting edge WxT 200/20 mm 200/20 mm
Weight 340 kg 365 kg
Series H Series HT Series HD
Contracting bucket. The very strongest buckets in the series. They are based
on the H bucket. On the 210, 240 and 260, the metal is 20 % thicker how-
ever. In addition, the HD buckets have a more powerful cutting edge, a
wider, longer floor reinforcement, an extra angle reinforcement on the inside
of the bucket along the implement hooks, as well as an angled wearing rail
on the rear of the bucket.
The soil bucket – the most popular in the range – can do everything. The
short bucket bottom makes the bucket strong and well suited to heavier
tasks. The three large buckets have an extra profile and round pressed back
plate across the full width.
Soil bucket with teeth. Same design as series H.
32 | Quicke Dimension
Buckets
Series lv 200lv 220lv Volume (heaped) 1.13 m3 1.25 m3
Width 200 cm 220 cm
Depth 100 cm 100 cm
Height 85 cm 85 cm
Cutting edge WxT 100/16 mm 100/16 mm
Weight 243 kg 262 kg
Series hv 200hv 220hv Volume (heaped) 1.16 m3 1.28 m3
Width 200 cm 220 cm
Depth 104 cm 104 cm
Height 85 cm 85 cm
Cutting edge WxT 150/16 mm 150/16 mm
Weight 273 kg 294 kg
240hv 260hv Volume (heaped) 1.70 m3 1.85 m3
Width 240 cm 260 cm
Depth 109 cm 109 cm
Height 98 cm 98 cm
Cutting edge WxT 200/20 mm 200/20 mm
Weight 415 kg 443 kg
A strong material and snow bucket. The series is aimed at users who require
a large volume. The generous volume measurements are achieved by de-
signing the bucket deeper and taller. All models have double profiles in the
bottom as well as along the implement hooks. There is consequently extra
strength where the stresses are greatest.
Series hv Series l Series lv
Light bucket. If the bucket is only to be used for lighter duties, the L bucket
is an excellent choice. The bucket is designed for customers who value
functionality ahead of technical benefits. The price is therefore extremely
competitive.
Light Volume bucket. This bucket series is suitable for handling grain,
manure, grass seeds, wood chips and other materials with a low volume
weight. The buckets have two vertical reinforcements along the implement
hooks.
In the emptying position, the front loader’s effective emptying stop ensures
controlled and complete emptying of the implement. Note also how the
“boomerang-shaped” link on the front loader contributes to a maximum
emptying angle.
Th
e best choice
A good ch
oice
Which bucket should I choose?
Areas of application H HT HV HD L LV
Light excavation and loading work
Loading of e.g. grain, wood chips and snow
Loading of lighter materials at high level
Heavy excavation and loading work
Work in gravel/sand, earth and stone
Contract work in gravel/sand, earth and stone
Grading work
Professional snow clearance
Grading
bucket
High
tip
Series l 130l 180l Volume (heaped) 0.51 m3 0.71 m3
Width 130 cm 180 cm
Depth 80 cm 80 cm
Height 75 cm 75 cm
Cutting edge WxT 100/12 mm 100/12 mm
Weight 136 kg 171 kg
Selecto F
ix – Easier implemen
t changes
Quicke Dimension | 33
Universal fork
High tip bucket 230
Volume (heaped) 2.00 m3
Width 230 cm
Depth 120 cm
Height 120 cm
Cutting edge WxT 150/20 mm
Weight 480 kg
Stone fork - Pro 150 200 Width 150 cm 200 cm
Depth 100 cm 100 cm
Height 73 cm 73 cm
Number of bottom tines 14 18
Tine distance 11 cm 11 cm
Weight 235 kg 292 kg
Universal fork 150 200 Width 150 cm 200 cm
Height 73 cm 73 cm
Tine length 98 cm 98 cm
Number of bottom tines 14 18
Tine distance 11 cm 11 cm
Weight 249 kg 310 kg
Stone fork – Professional
Forks
GRADING bucket 220
Volume (heaped) 0.65 m3
Width 220 cm
Depth 110 cm
Height 50 cm
Cutting edge WxT 150/20 mm
Weight 337 kg
High tip bucket Grading bucket
Without doubt the most powerful stone/universal fork on the market.
On the specially hardened box section, which does not become deformed
under load, powerful stone fork tines are installed. The back comprises five
transverse 80 x 40 profiles. The design
is incredibly torsionally rigid, at the
same time as offering excellent vis-
ibility. On the sides, the forks
are supplied with powerful
Hardox teeth.
A powerful grading bucket. Thanks to the low back plate and the long,
strong base, the driver has perfect visibility to the tip of the bucket. The
bucket is supplied with a 20 mm, powerful cutting edge. On the rear, below
the 20 mm thick subframe plates, is a welded 10 mm thick angle iron, which
reinforces the bucket for grading jobs.
The high tip bucket increases the unloading height by 120 cm. As a result,
even a short, compact front loader can fill a high trailer if necessary.
The bucket tips over its front edge, and it is not therefore necessary to
wait for the front edge to be lifted over the truck side before you reverse
away. This saves time and increases productivity.
High tip buckets are used for handling voluminous materials at high lev-
els, for example for loading grain, grass seed, beet or wood chips.
“Pick up and keep”. The distinctive design provides considerable potential
to fill the implement without dropping any stones already contained in the
bucket. At the front, special downward-
angled tines made of Hardox steel are
installed. After many hours of work,
these can easily be replaced.
The cross tubes (50 x 100 mm)
provide stability for the 30 mm
thick tines. Note also that
the back of this model
is higher than on earlier
models.
Selecto F
ix – Easier implemen
t changes
34 | Quicke Dimension
Lifting implement
Pallet forks Big bag lifter
Big bag lifter Weight 118 kg
Max. load 800 kg
Widht 120 cm
Height 170 cm
The upper profi le is made in one piece. This profi le
with holes for lateral adjustment provides robust
securing of the forks. The load is distributed over a
large area thanks to the wide load-bearing surfaces
of the forks. With this special
design, breaks in the arm are
avoided and you get to operate
a very stable fork that does not
“dangle”. The forks are natural-
ly approved with a large safety
margin.
For safe handling of large bags. The
height of the hook above the ground is
normally the same as when the bot-
tom of the large bags is level with
the lowest point of the front loa-
der when the bags are hanging
from the big bag lifter. Note
the practical benefi t of having
the hook bent to the side. The
hook can easily be seen from
the driver’s seat.
Log grab attachment
Bale spike (one short and one long tine). For instal-
lation on the pallet fork subframe.
Suitable for 1,000 kg, 1,600 kg
and 2,500 kg fork kits.
Weight 24 kg
Weight 85 kg
Accessories - Pallet forks
Accessories
3-point linkageThis implement can be used like the tractor’s 3-point
linkage to help move some implements around the
farm. Available with either Euro or SMS hooks.
Counter-weight
Weight 78 kg
The counter weight is an extremely useful piece
of equipment to properly ballast your machine to
maintain weight on the tractor’s rear axle.
The counter-weight increases the stability for the
tractor-loader unit. Connecting and disconnecting of
the counter-weight is made very easily with help
of the attached coupling axle, which has a bracket that
prevents the weight from coming off during work.
Bale spike
Pallet forks
1,000 kg 1,600 kg 2,500 kg Weight 122 kg 160 kg 170 kg
Max. load 1,000 kg 1,600 kg 2,500 kg
Width 140 cm 140 cm 140 cm
Fork
length 97 cm 97 cm 120 cm
Fork heigth 50 cm 92 cm 95 cm
Fork type profi le wrought wrought
The counter-weight is available in two sizes and is always delivered empty.
Weight, empty Weight, fi lled
(not factory fi lled)
186 kg 800 kg with concrete
212 kg 1000-1200 kg with concrete
NB: fi lled weight can be increased with metal
Quicke Dimension | 35
Your security first and foremost
A loader’s service life and efficiency increase if it has access to good service. When you choose a Quicke loader, you have a strong global organisation behind you.
In recent years we have invested even more in building up a comprehensive service network. In order to provide you with the best possible back-up, the entire organisation works towards a single goal: 100 % customer satisfaction.
• Absolute customer focus. In order to support you as a customer, we have built up procedures that ensure all departments in our
organisation concentrate on your needs.
• Proximity. Our world-leading distribution network is guaranteed to be close to you, no matter where you are.
• Extensive spare parts network. Spare parts are available from our subsidiary companies and from major Quicke representatives
all over the world.
• Rapid assistance on the web. Via Internet you have access to spare parts information, instructions and other vital information.
• Global technical support. As a Quicke customer, you always have access to rapid technical support. All over the world, our repre-
sentatives can provide knowledgeable and appropriate service.
• Continuous follow-up. Your opinions and suggestions for improvements to our product range are gathered up and processed
centrally. This process acts as a valuable foundation when we develop new loaders, implements and subframes. The new Quicke
Dimension is the fruit of close co-operation with users all over the world!
ps.
po
nd
us:
060
5. p
ho
to: j
ost
ein
ske
idsv
oll.
rep
ro: Z
irco
n M
edia
The Quicke dimension | www.quicke.nu
Some front loaders in this brochure are fitted with extra equipment. Certain products may be optional extra equipment. Some of the products are not available on all markets. Working with front loaders and accompanying implements is not without risk. Serious injuries to people and damage to materials can occur in the event of incorrectly carried out work. Show consideration to your surroundings, use com-mon sense and comply with local laws and regulations. Always read carefully through the instruction manual supplied. Only use original spare parts and accessories. Ålö’s product range is continually being
developed. We reserve the right at any time to alter specifications, prices and versions with no obligation on our part.®, ™ Trademarks of Ålö AB.
Ålö AB, SE 901 37 Umeå, Sweden Tel: +46 (0)90-17 05 00. Fax: +46 (0)90-17 05 99
www.alo.se
Best
nr 1
114
4328
Recommended