View
218
Download
0
Category
Preview:
Citation preview
-17091 -17101-17091 -17101
High Precision Cross Roller
Part Number
ZPG60
QZ-Axis
Con�gure Online
QFeature: Cross Roller Z-Axis Stages made of lightweight aluminum alloy. EZPG80-CR will be discontinued in March 2013.
High Precision Linear BallMicrometer Head / Feed Screw
Part NumberZSG60
ZSGB60
QFeature: High Precision / rigidity and economical Linear Ball Slide Z-Axis Stages. Further cost savings is possible by selecting the Feed Screw Type. Low Temp. Black Chrome Plated Types are also available. Suitable for applications where light reflections are to be avoided.
Q�Z-Axis
W�X-Axis P.1681W�XY-Axis P.1695
W�X-Axis P.1685W�XY-Axis P.1699
QOther Information about StagesStage Selection Table P.1639, P.1640New Products P.1641About Standard Stages P.1642Overview, Technical Information P.1643, P.1644
QOther Information about StagesStage Selection Table P.1639, P.1640New Products P.1641About Standard Stages P.1642Overview, Technical Information P.1643, P.1644
Con�gure Online
* Ø7 for A=25.
QMicrometer HeadZSG (25≤A≤80)
ZSGB (Low Temp. Black Chrome Plating: A25, 40, 60, 80)
QFeed Screw (Pitch 0.5)
ZSCG (25≤A≤80)
ZSCGB (Low Temp. Black Chrome Plating: A25, 40, 60, 80)
05
Clamp {(M3x5)(M2x3.5 for A=25)}
X
4-d Through
Clamp {(M3x5)(M2x3.5 for A=25)}
X
A N W
t
J
F
yY
Z(C
)A
HK
A J
F
(C)
AH
K
G
D
N W
t
GØ13*
P Q
yY
Z
P Q
4-d Through
EZ-Axis of A25 has different bracket configuration.E�For top surface mounting dimensions and feed bracket
shapes, see Linear Ball Slide X-Axis Stages on P.1681.
E�Standard Datum Configuration
EMISUMI's Linear Ball Guide Stages have parallel and orthogonal datum in relation to the motion axis as shown by the illustrations.
Base Line
Base Horizontal PlaneParallelism: 0.02
Orthogonality: 0.04Base Vertical Plane
Moving Axle (Imaginary)
TypeMain Body Ball Spring Micrometer Head Bracket Tip Holder
MMaterial S MMaterial HHardness MMaterial MMaterial S MMaterial S
ZSGZSCG 440C
Stainless Steel
Electroless Nickel Plating 440C
Stainless Steel
58HRC~304
Stainless Steel PB
5052 Aluminum
Alloy
Clear Anodize 303 Stainless
Steel
-
ZSGBZSCGB
Low Temp. Black Chrome Plating
Black Anodize
Low Temp. Black Chrome Plating
EFor Micrometer Head and Feed Screw materials, see P.1733, 1734.ECharacteristics of Black Chrome Plating: D�P.112
QMicrometer Head (ZSG, ZSGB) / Feed Screw (ZSCG, ZSCGB)Part Number Front View Side View Top View Accessories (4 pcs.)
Type A H(C) Travel Distance
F K J D G N W t P Q X Y y Z d Type M-LMicrometer Feed Screw (mm)
ZSGZSCGZSGB (* only)ZSCGB (* only)
25* 12.5 37 23 ±3.2 13 10 6.8 9.3 10 12 20 5 6 3.5 20 10 2.5 19.5 2.5 SCB2-840* 35
58.5 55 ±6.5
20 14 11.5 13 13 14 31 5 10 5.5 32 16 4 25 3.5 SCB3-1050 30 20 19 11.5 13 13 14 57 5 10 5.5 40 40 6 25 3.5 SCB3-1060* 25 20 24 11.5 13 13 14 42 8 10 5.5 50 25 5 26 4.5 SCB4-1270 25 20 23.5 11.5 13 14 16 55 8 10 6.5 40 40 4 27 3.5 SCB3-1280* 20 96 ±12.5*1 24 25 11.5 18 16.5 20 45 7 10 5.5 50 25 5 35 4.5 SCB4-12
*1 When A=80, the feed screw (ZSCG, ZSCGB) travel is ±6.5.
· PerformancePart Number Stage Surface
(mm)Load Capacity
(N)Accuracy Moment Load Capacity (N·m) Moment Rigidity ("/N·cm) Weight
(kg)Unit Price 1~9 pc(s).
Type A Straightness Pitching Yawing Pitching Yawing Rolling Pitching Yawing Rolling ZSG ZSCG ZSGB ZSCGB
ZSGZSCGZSGB (* only)ZSCGB (* only)
25* 25x25 9.8 3µm 30" 25" 2.0 2.0 3.5 1.90 1.10 1.10 0.09 40* 40x40
491µm*2 25" 15"
5.0 5.0 5.0 0.42 0.35 0.21 0.32 50 50x50 6.8 6.8 6.0 0.15 0.14 0.09 0.44 - -60* 60x60 10.0 10.0 9.0 0.08 0.08 0.05 0.58 70 70x70 13.8 13.8 12.9 0.06 0.05 0.03 0.84 - -80* 80x80 3µm 18.2 18.2 17.7 0.04 0.04 0.02 1.20
EZSG and ZSGB: Micrometer Head Resolution 10µm/division * 2 ZSGB and ZSCGB straightness is 3µm. EFor orders larger than indicated quantity, please request a quotation.
EStandard Stages Similar Products: ZLBS (P.1656)
EMounting dimensions of micrometer head, feed screw and clamp are different from those of standard products. See the CAD data for details.EFor micrometer head or feed screw mounted in positions other than shown below, see "Specification Selectable Type". (P.1711)
EKnob Cover HDCVR13 (Sold Separately): Ø13 mm knob diameter can be increased by installing the cover. W P.1683EExtension Cover HDEXT13 (Sold Separately): Ø13 mm head or feed screw knobs can be extended by installing the cover. W P.1683EFor 25 Square Opposed Clamp, the bracket material is 303 Stainless Steel.
Alterations Position of Micrometer Head and Feed Screw Reinforced Clamp
Spec.
Side Up Side Up and Right/Left ReversedSide Down
E�A disc clamping method that does not apply loads on the stage surface. Better position holding performance than the standard clamping method.
XNot applicable to ZSCG, ZSGB and ZSCGB.EApplicable only when alteration C or CR is selected
with ZSG25, 40, 50, 60, and 70.E The side drive micrometer head is opposed by a screw (M4x25, pitch 0.5).
Improves vibration resistance and has secure position holding performance.E When A=25, * marked dimensions are applicable. G
dimension in the table will be 6. Note that the micrometer protrudes 17.5mm (±3.2) from the Z-axis bracket.
Code C CR CU H PPrice Adder
Disc ClampSide Up Side DownSide Up and Right / Left Reversed Opposed Clamp
XNot applicable to 25 square.X�Not applicable to ZSGB and
ZSCGB.
A (B1)25 17.540 24.550 19.560 14.570 4.0
A J1 P1
40, 50, 60, 70 15.8 1080 14.8 15
50
J16.
2 P1 18.5(*11.7)12(*7)
(B1)±
6.5(
* 3.2
)
Part Number - (C, CR, CU, H, P)
ZSG40 - CCon�gure Online
ZPG
· Mounting Hole Dimensions of the Top Table
A25 A40 A60 A80
yY
Z
P Q
J
K H t
A(B
)
WN
X
F
G
D
A1
A
4-d1 Through
Clamp (M3x5)
d2 Counterbore
25
10 10
1010
25
40
16 16
40
1616
60
25 25
32
6025
2532
8070
25 25
80 70
2525
8-M2, Depth 5
12-M4, Depth 6
M16xP1.0, Depth 6
M6xP1.0, Depth 6
8-M3, Depth 64-M3, Depth 6
M16xP1.0, Depth 6
8-M4, Depth 6
M2x3.5 for A=25
M Material: Aluminum AlloyS Surface Treatment: Black Anodize
QMicrometer Head (ZPG)Part Number Front View Side View Top View Accessories (4 pcs.)
Type A A1 H (B) Travel Distance (mm) F K J D G N W t P Q X Y y Z d1 d2 Type M-L
ZPG
25 25 12.5 37.0 ±3.2 11 22.5 6.8 9.3 12.5 15 20 5 6 4.5 20 10 2.5 22.5 2.5 - SCB2-840 50 35.0 58.5 ±6.5 24 47.0 6.5 13.0 17.0 20 30 4 10 5.5 32 16 4.0 30.0 3.5 6 SCB3-860 70 20.0 58.5 ±6.5 24 37.5 6.5 13.0 17.0 20 45 7 10 5.5 50 25 5.0 35.0 4.5 8
SCB4-1280 80 20.0 96.0 ±12.5 24 45.0 11.5 18.0 16.5 20 45 7 10 5.5 50 25 5.0 35.0 4.5 8
· Performance
EFor orders larger than indicated quantity, please request a quotation.EMicrometer Head Resolution: 10µm/division
Part Number Stage Surface Load Capacity (N)
Accuracy Moment Load Capacity (N·m) Moment Rigidity ("/N·cm) Weight Unit PriceType A (mm) Straightness Pitching Yawing Pitching Yawing Rolling Pitching Yawing Rolling (kg) 1~9 pc(s).
ZPG
25 25x25 4.9
3µm
30" 30" 1.1 0.8 0.4 3.03 2.85 1.80 0.06 40 40x40 9.8
25" 15"2.7 2.2 2.0 0.38 0.42 0.28 0.20
60 60x60 19.6 5.2 4.3 5.5 0.12 0.11 0.07 0.45 80 80x80 49.0 19.2 15.1 17.3 0.05 0.05 0.04 0.80
ESimilar Standard Stage Products (available for limited sizes only): ZCRS (P.1658)
EMounting dimensions of micrometer heads and clamps are different from those of standard products. Bracket shapes differ depending on the sizes. See the CAD data for detailed dimensions.EKnob Cover HDCVR13 (Sold Separately): Ø13 mm knob can be increased in diameter by installing the cover. W P.1683EExtension Cover HDEXT13 (Sold Separately): Ø13 mm head knob can be extended. W P.1683
Alterations Micrometer Head Position Reinforced Clamp
Spec.
Code C CR CU H P
Price Adder
Opposed ClampDisc ClampSide Up
EA disc clamping method that does not apply loads on the stage surface. Better position holding performance than the standard clamping method.
EH dimension is changed. EH dimension is changed. EH dimension is changed.
EThe side drive micrometer head is opposed by a screw (M4x25, pitch 0.5). Improves vibration resistance and has secure position holding performance.
XNot applicable to 25 and 80 square.E Applicable only
when alteration C or CR is selected for ZPG40/60.
Side Up and Right / Left Reversed Side Down
14.8
6.2
Ø15
18.5 12
B1±6.5A B1
40 22.560 11.0
A H25 12.540 3560 2080 50
A H25 12.540 3560 2080 50
A H25 12.540 2060 2080 20
Part Number - (C, CR, CU, H, P)
ZPG80 - CU
Con�gure Online
For Pricing and Days to Ship,Please Con�gure Online.
Recommended