Pure IP PBX KX-TDE600 MPR 2.00 Panasonic Communications CO.,LTD

Pure IP PBX KX-TDE600

MPR 2.00

Panasonic Communications CO.,LTD.

TDE600MPR 2.00TDE600MPR 2.00

“Pure IP-PBX KX-TDE SeriesProduct Line Up

TDE100/200MPR 2.00TDE100/200MPR 2.00

TDE100/200MPR 1.00TDE100/200MPR 1.00

TDE600 The same as TDE200 MPR 2.0/TDA600 MPR 5.0(MPR 2.0) New activation key.

Version Main FunctionTDE100/200 - Peer to Peer Communication(MPR 1.0) - KX-NT300 Series IP-PT

- SIP Phone CompatibleTDE100/200 - KX-TDA0177 (CSLC16)(MPR 2.0) - Improved Built-in SVM2

- KX-TDA0192/4 (ESVM)- 8 Digits VM Integration- Support T38 (ITU standard for sending FAX)

KX-TDE600 System Highlights “

Build - up system (Flexible system: same as TDA600) Inherent TDA600 MPR 5.0 Features. Inherent TDE100 MPR 2.0 Features. Easy upgrade from TDA600 to TDE600

(Change EMPR card to IPCEMPR card) TDA600 Hardware products compatible with TDE600. TDE100 Activation keys compatible with TDE600. CA (NCP) feature is not supported. TDE600 does not support build-in SVM. New activation key for TDE600. Support KX-NT3xx Series Support KX-DT3xx Series PA: TDE600 supports PA 1.8 only. (Do not use PA 1.7 or

early version.)

“

DLCDHLC

Router

VoIP/SIP

PCMC

TDE100/200 SeriesActivation Key

IPCEMPRDSP

DT300T7600

NT136NT300

NT300

TDA0470

MPR 2.0

TDA600 MPR 5.0 FeaturesTDE100 MPR 2.0 Features

KX-TDE600 System Highlights

KX-TDE600 Shelf

Difference from TDA620- Front cabinet

KX-TDE620

Expansion Shelf

KX-TDE600

Basic Shelf

Difference from TDA600- MPR Card- Front cabinet

“

KX-TDE600 Shelf (Build up)

Entry FullMedium-1 Medium-2

KX-TDE620

KX-TDE620

KX-TDE620

KX-TDE600 KX-TDE600KX-TDE600KX-TDE600

KX-TDE620KX-TDE620

KX-TDE620

The same concept as the TDA600

KX-TDE600 Shelf “

1 x Virtual Shelf

4 x Physical Shelf

The same as the TDA600

KX-TDE600 Virtual Slot “

4 x Virtual SlotExtension

4 x Virtual SlotTrunk

Total Max 8 x Virtual Slot

The same as TDE100/200.

KX-TDE600 Max. Slot “

TDE600 TDE600+

TDE620 x 1

TDE600+

TDE620 x 2

TDE600+

TDE620 x 3

System Max 18 29 40 51

Trunk Max 14 24 34 40

Physical Slot 10 20 30 40

Virtual Slot 4 4 4 4

Extension Max. 14 24 34 40

Physical Slot 10 20 30 40

Virtual Slot 4 4 4 4

Physical Slot 10 21 32 43

KX-TDE600 Terminals (Trunk) “

TDE600 TDA600

Trunk Max. 640 640

SIP G/W Virtual (MPR) 32 (2 x SIP G/W-16) -

Traditional 0 -

Max. 32 -

H.323

G/W

Virtual (MPR) 32 (2 x V-G/W-16) -

Traditional 640 (40 Slots) 640 (40 Slots)

Max. 640 640 (40 Slots)

LCOT/BRI

Traditional 640 (40 Slots) 640 (40 Slots)

PRI30/E1 Traditional 600 (20 Slots) 600 (20 Slots)

PRI23 Traditional 460 (20 Slots) 460 (20 Slots)

T1 Traditional 480 (20 Slots) 480 (20 Slots)

KX-TDE600 Terminals (Trunk) “

TDE600TDE600 +

TDE620 x1

TDE600 +

TDE620 x 2

TDE600 +

TDE620 x 3Trunk Max. 192 (*1) 352 (*2) 512 (*3) 640Virtual Max 32 32 32 32

SIP 32 32 32 32IP-G/W 32 32 32 32

Traditional Max. 160 320 480 640Analogue 160 320 480 640BRI 160 320 480 640PRI30/E1 150 300 450 600PRI23 115 230 345 460T1 120 240 360 480IP-G/W 160 320 480 640

(*1) 192: 160 (BRI x 10) + 32 (Virtual)(*2) 352: 320 (BRI x 20) + 32 (Virtual)(*3) 512: 480 (BRI x 30) + 32 (Virtual)

KX-TDE600 Terminals (Extension) “

TDE600 TDA600

Extension Max 1152640: TDA0172 x 20

128: SIP (32 x 4 Slot)384: TDA6178 x 16 Slot

1120

IP-PT

(MGCP)

Virtual (MPR) 64 (2 x V-IPExt-32) -

Traditional 640 (40 Slot) 640 (40 Slot)

Max. 672 640

SIP Ext. Virtual (MPR) 128 (4 x V-SIP-32) -

Traditional 0 -

Max. 128 -

PT Traditional 640 640

SLT Traditional 960 (40 Slots x SLC24) 960 (40 Slots x SLC24)

PS (w/o MEC / w/ MEC) 512/512 256/512

KX-TDE600 Terminals (Extension) “

TDE600TDE600+

TDE620 x1

TDE600+

TDE620x 2

TDE600+

TDE620x 3System Max. w/ DXDP 432 736 1008 1152

w/o DXDP 368 608 848 992Virtual Max 128 128 128 128

SIP 128 128 128 128IP-PT 64 64 64 64

Traditional Max. w/ DXDP 304 608 880 1120w/o DXDP 240 480 720 960

SLT Max 240 480 720 960PT Max. 256 512 640 640PT w/ DXDP 256 512 640 640PT w/o DXDP 160 320 480 640

IP-PT 160 320 480 640

CS 32 64 96 128

PS (w/o MEC/ w/ MEC) 512/512 512/512 512/512 512/512

“KX-TDE600 Compatibility

PRI (TDA0290)

BRI-4 (TDA0284)

BRI-8 (TDA0288)

CID (CO:TDA0193)

E1 (TDA0188)

ELCOT-16 (TDA6181)

Card

CID/PAY8 (TDA0189)

IP-GW4 (TDA0480)

IP-GW4E (TDA0484)

IP-GW16E (TDA0490)

Yes

Yes

Yes

Yes

Yes

Yes

TDA600

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Yes

TDE600

Yes

No

Yes

Yes

IPCMEC (TDE0105) Yes No

- Compatibility with TDA600 option cards. (Trunk/System)

EMEC (TDA6105) No Yes

Card TDA600

PSU-L (TDA0103)

Master-Sub (TDA6111)

Yes

Yes

TDE600

Yes

Yes

Bus-Master (TDA6110) YesYes

PSU-M (TDA0104) YesYes

TDE600 does not support.- LCOT-4 (TDA0183)- LCOT-8 (TDA0180)

“

CSLC-16 (TDA0177)

DHLC-8 (TDA0170)

SLC-8 (TDA0173)

DLC-16 (TDA0172)

Card

DLC-8 (TDA0171)

CS-I/F (TDA0144/0143)

TDE600

DPH-2 (TDA0162)

DPH-4 (TDA0161)

OPB-3 (TDA0190)

Yes

Yes

Yes

TDA600

Yes

Yes

Yes

Echo-16 (TDA6166)

CTI-LINK (TDA0410)

IP-Ext-16 (TDA0470)

MSG (TDA0191) Yes Yes

Remote (TDA0196) Yes Yes

Ext. CID (TDA0168)

- Compatibility with TDA600 option cards. (Extension)

ECMSLC-24 (TDA6178)

ESLC-16 (TDA6174)

EMSLC-16 (TDA6175)

Card

Yes

Yes

Yes

YesYes

Yes

Yes

Yes

Yes

YesYes

YesYesYes

YesNo (*1)

YesYes

YesYes

Yes

Yes

Yes

Yes

YesYes

TDA600 TDE600

E-SVM-4 (TDA0194) Yes Yes

E-SVM-2 (TDA0192) Yes Yes

*1: IPCEMPR Card has the CTI link port.

KX-TDE600 Compatibility

TDE600 does not support.- SLC-16 (TDA0174)- SLC-16 (TDA0175)- ECHO-16 (TDA0166)

“

- Compatibility with TDE100/200 Activation keys.

Feature Enhancement (NCS4950)

2-IP Trunk (NCS4102)New activation keys.

8-IP Soft-/IP-PT (NCS4208)

Activation key

No

No (*1)

Yes

Yes

Yes

Yes

TDE100 TDE600

KX-TDE600 Compatibility

Feature Enhancement (NCS4910) YesNo

4-IP Trunk (NCS4104) YesYes

1-IP Soft-/IP-PT (NCS4201) No (*1)Yes

8-IP-PT (NCS4508) YesYes

1-IP-PT (NCS4501) No (*1)Yes

16-SIP Phone (NCS4716) YesYes

1-SIP Phone (NCS4701) No (*1)Yes

*1: TDE100/200 MPR 2.01 will support.

“

- Compatibility with TDE100/200 options.

VoIP Encryption SD card (TDES61)

VoIP Encryption SD card (TDES01)

DSP-64 (TDE0111)

No

Yes

Yes

DSP-16 (TDE0110) Yes

TDE100 TDE600

Yes

No

Yes

Yes

KX-TDE600 Compatibility

“

All Activation products of TDE600

All Activation products of NCP

No

Yes

Yes

No

NCP TDE600

KX-TDE600 Compatibility

All Hardware of TDE600

All Hardware of NCP

No

Yes

Yes

No

- Compatibility with NCP500/1000

System Connection TDE600 & TDE620

TDE600

TDA6110 (BUS-M)

TDE600TDE600

TDE620/TDA620

TDE620/TDA620

Cable

Cable

Power unitLPR Cards

TDA6110 (BUS-M)

TDA6111(BUS-M-Sub)

TDA6111(BUS-M-Sub)

A cable is packed in BUS-M (TDA6110), BUS-M-Sub (TDA6111)

TDE620/TDA620TDE620/TDA620

TDA620 Software should be 2.000 or later.

Activation Key

“Activation Key- Issuing TDE600 activation key procedure is the same as TDE100/200.

URL: https://eww.netreg.panasonic.co.jp/kms/

KX-TDE6101 IPCEMPR KX-TDE0105 IPCMEC

“KX-TDE600 IPCEMPR (TDE6101)- KX-TDE6101: MPR card for TDA600.(KX-TDE600 has KX-TDE6101)

-KX-TDE0105 Memory Expansion Card for IPCEMPR

Build-in Memory Card

“KX-TDE0105 (IPCMEC) Feature

ItemsTDE600 MPR 2.0 TDA600 MPR 5.0

W/o TDE0105

W/TDE0105 W/o MEC W/MEC

4 Party Conference With Broadcasting.

Yes Yes No Yes

System Speed Dial1000/Tenant

x 321000/Tenant

x 321000/Tenant

1000/Tenant

x 32Station Speed Dial 100/Ext.

Yes Yes No Yes

Hotel-SMDR for check out.

4000 Calls 8000 Calls No 8000 Calls

SDMR buffer 1000 Calls 4000 Calls 1000 Calls 4000 Calls

Quick Dial 8Digit,

4000 entriesYes Yes Yes Yes

Max. Number of PS 512 512 256 512

The procedure detailed below is for your reference regarding the addition of a IPCMEC card to a previously installed TDE600.

1. Save the current system data from the TDE to the SD card2. Save the current system data from the SD card to your PC.3. Power off the TDE and remove the preinstalled MEC card.4. Install an IPCEMEC to the TDE.5. Power on with initial initializing steps.6. Connect the PCMC and initialize the TDE.7. Upload the system data to the TDE.

Procedure adding IPCMEC “

Note:When the preinstalled memory card is removed, all recorded SMDR data will be lost. Therefore, it is recommended to output the SMDR data before removing the preinstalled memory card.

Important

TDE600 Software

“TDE600 Software

TDE600 supports,TDA600 MPR 5.0 Features.

- KX-TDA0158 (8ch-CS)- KX-TDA6178 (24-SLT)- 8 digits VM integration- KX-TDA0192/4 (ESVM)- Moving From SVM to DISA- High Quality OGM Record to ESVM

TDE100 MPR 2.0 Feature.- T.38

“TDE600 Software

Modified/New Functions/Features

Modified/New Functions/Features

1 VM-Group Ext. number can be assigned as transfer re-call destination.

2 Intercept function performs an extension which set call forward to CO.

3 Auto recovery function for Busy-out (Analogue line).

4 Two CLIP on an Extension.

5 Check-OUT not ready mode (Hotel feature) is supported.

6 System error activates an external relay.

7 PRI CNIP with the name of extension.

“Software Enhancement Plan

TDE600 NCP500NCP1000 TDA30 TDA100

TDA200 TDA600 TDE100TDE200

Transfer re-call to VM-Group. 2.0 1.0 (5.0) (5.0) (?) (3.0)

Intercept for Call-FWD to CO. 2.0 1.0 (5.0) (5.0) (?) (3.0)

Busy-out Auto recovery function. 2.0 1.0 (5.0) (5.0) (?) (3.0)

Two CLIP on an Extension. 2.0 (?) (5.0) (5.0) (?) (3.0)

Check-OUT not ready mode. 2.0 1.0 (5.0) (5.0) (?) (3.0)

System error activates an external relay.

2.0 1.0 (5.0) (5.0) (?) (3.0)

PRI CNIP 2.0 1.0 N/A (5.0) (?) (3.0)

( ) = Planed MPR version

PCMC for TDE600

“PCMC for TDE600Please use U-PCMC Ver. 4

“PCMC for TDE600Now file

“PCMC for TDE600Connect

Upgrade TDA/TDE to TDE600

“Upgrade to TDE600Update from TDA600The following items are necessary for the upgrade:Model/Name Description

KX-TDE6101 (IPCEMPR)

IP Convergence Main Processing Card

The main processing card for controlling the Pure IP-PBX (KX-TDE600). This card comes with an SD Memory Card and 2 ferrite cores included.

KX-TDE0110 (DSP16)

16-Channel VoIP DSP Card

Digital signal processor (DSP) cards to be mounted on the IPCMPR/IPCEMPR card.

Depending on the number and the type of IP trunks and IP telephones you wish to use, either the DSP16 or DSP64 card is selected to be installed.

Note

The following activation keys are pre-installed:

4-Channel IP Trunk Activation Key: 1 for

DSP16; 4 for DSP64

8-Channel IP Proprietary Telephone Activation

Key: 1 for DSP16; 4 for DSP64

KX-TDE0111 (DSP64)

64-Channel VoIP DSP Card

“

We can upgrade from TDA100/200/600/TDE100/200 to TDE600.The origin PBX System data is only versions of TDA100/200 TDA600 (MPR 5.0xxx), TDE100/200 (MPR 2.0).

TDE600System Data

Upgrade to TDE600

TDA600 MPR 5.0TDE100/200 MPR 2.0

PCMCData Converter

System data converter (By PCMC)

“

Not PossibleTDA100/200 MPR x.x

TDA600 MPR 3.0TDE100/200 MPR 1.0

Upgrade to TDE600

TDA600 MPR 5.0TDE100/200 MPR 2.0

PCMCData Converter

Data Convert

PCMCData Converter

Upgrade from TDA100/200 MPR x.x, TDA600 MPR 1.0, TDE100/200 MPR 1.0 to TDE600.

TDE600System Data

“Upgrade to TDE600

TDE600 requirements

- SLC16 is converted to ESLC16 automatically. - MSLC16 is converted to EMSLC16 automatically. - LCOT16 is converted to ELCOT16 automatically.

The following card has to be removed and the card data has to be deleted before system data convert.- LCOT-4 (TDA0183)- LCOT-8 (TDA0180)- VoIP-4 (TDA0480)- ECHO-16 (TDA0166)- CTI Link card (TDA0410)- Any card in Slot 11

PCMC data convert conditions

- Card configuration of TDE600 should be same as TDA/TDE.- If the MEC card is installed in the TDA, IPCMEC should be install.

“

The TDA SD memory card (TDA30/100/200: 32M, TDA600:64M) used in the TDA cannot be used TDE600 (128M).

The SD memory card contains software for all the processes of the PBX and all the customer data. It can be easily removed and taken away from the PBX by a third party. Therefore, do not allow un-authorized access to prevent data leakage. To prevent data leakage, render the SD Memory Card physically unusable before disposal.

Upgrade to TDE600

Note:

“

• Incoming Call Log• Outgoing Call Log (including Last Number Redial)• Message Waiting• SMDR• Advice of Charge (AOC)/Pay Tone• Hospitality guest billing data• ICD Group monitor log for supervisor• PBX date and time• Timed Reminder• LPR Timed Update time• Daily test start time• PT handset/headset volume• PT SP-PHONE volume• PT ring volume• PT display contrast• ICD Group login status

Upgrade to TDE600

Data Reset After Upgrade

“

• ICD Group login status (All extensions are set to Login by default.)• ICD Group Ready/Not Ready status

(All extensions are set to Ready by default.)• Live Call Screening (LCS) On/Off• Hands-free Answerback status• Absent Message status of extensions

(Absent Message data itself is not cleared.)• FWD/DND status

(FWD destinations are not cleared.)• Extension Lock/Remote Extension Lock• Extension PIN Lock/Extension PIN Lock counter• Verified Code PIN Lock/Verified Code PIN Lock counter• Password Lock counter for Remote System Programming• PBX Error Log• Digital Trunk Error Report data

Upgrade to TDE600

Upgrade Steps

“

1- Back up the current system data.2- Back up the current OGM files3- Open the current system data by batch mode.4- Delete the following card from the system data

- LCOT-4 (TDA0183)- LCOT-8 (TDA0180)

- VoIP-4 (TDA0480) - ECHO-16 (TDA0166) - CTI Link card (TDA0410) - Any card in Slot 11

5- Save the system data.

Upgrade to TDE600

This steps is operated by the PCMC, but PCC recommends this step by manually.

“

6- Convert the saved system data file for use with the TDE600.

Upgrade to TDE600

6.1- Open U-PCMC 4.0.

6.4- Select “By file”

6.3- Select “PBX”- TDA600 → TDE600- TDE100/200 → TDE600

6.5- Click “Next”

6.2- Click

“Upgrade to TDE600

6.6- Select source file (TDA600 MPR 5.0 or TDE100/200 MPR 2.0) and click “OK”

6.7- Select destination file and click “OK”The source file is automatically converted the TDE600 system data.

7- Set up a new TDE600, or TDA600[TDA600]Remove the current MPR card from the TDA600 and Install the IPCEMPR Card with either the DSP16/DSP64 Card mounted, in the TDA600.

8- Slide the System Initialize Switch to the "SYSTEM INITIALIZE" position.

9- Turn on the power to the PBX.10- Connect the U-PCMC to the TDE600.11- Quick set up.12- Transfer the converted TDE600 data to the TDE by U-PCMC.

“Upgrade to TDE60013- Activate the user DGSYS from the PC.

Select “Utility” - ”System Reset” - “Reset by the Command”.

13.1- Select

Important

13.2- Click “OK”

“

[ Final settings ]TDA Flash ROM- PGMPR 2.0- DGSYS (2.0 User)

SD Card- PGMPR 2.0

- DGSYS (2.0 User)- DGSYS_SUB (2.0)

MPR.2.0

Upgrade to TDE600

Upgrade Steps(TDA620 to TDE620)

“Upgrade from TDA620 to TDE620 -11- Check the present BUS-S software version.

Should be 2.0xx

“

2- Transfer the BUS-S software (2.0xx) to the SD card.

pbuss_v02xx.bin

Upgrade from TDA620 to TDE620 -2

SD Card- PGMPR 2.0- DGSYS (2.0 User)- PBUSS 2.0

MPR.2.0

“

Click to “OUS”

3- Set the TDA620 to “OUS” mode.

Upgrade from TDA620 to TDE620 -3

“

4-2 Click

4- Transfer the BUS-S software (2.0xx) to the TDA620.

4-1 Select

4-3 Select

4-4 Click

Upgrade from TDA620 to TDE620 -4

“

4-5 Click

4-6 Click

Present Software version

Upgrade from TDA620 to TDE620 -5

“

Click “OUS”

4-7 Click

4-8 Click

Upgrade from TDA620 to TDE620 -6

“

4-9 Click

Upgrade from TDA620 to TDE620 -7

“

5- Set the TDA620 to “INS” mode.

Click to “INS”

Upgrade from TDA620 to TDE620 -8

“

6- Check the present BUS-S software version.

Should be 2.0xx

Upgrade from TDA620 to TDE620 -9

Thank you very much !