View
215
Download
2
Category
Preview:
Citation preview
Product Certificate DORMA-Glas GmbH herewith confirms that the product
VISUR double-action door system has successfully completed a durability test aligned to EN 1154. This was conducted on the basis of a representative test series in which the fittings were applied to an all-glass door weighing 85 kg. Dimensions of the door leaf (width x height) 1100 mm x 2500 mm, toughened safety glass The door satisfied the requirement specified in EN 1154 of successfully completing 500,000 operating cycles. Further, pendulum impact tests were also carried out using a 40 kg pendulum. Test 1: Point of impact in the area of the rotating axis, 900mm above the floor surface. Pendulum drop height 305 mm. Test 2: Point of impact in the area of the primary closing edge, 900mm above the floor surface, during door closure in the opposite direction. Pendulum drop height 305 mm. The door satisfied the requirement: Functionally intact after pendulum impact test. Bad Salzuflen, 21 June, 2007 Dipl.-Ing.
Thomas Vogler Division Glass Head of Mechanical Design
DORMA-Glas GmbH Max-Planck-Str. 33-45 D-32107 Bad Salzuflen Germany
Product Certificate
DORMA-Glas GmbHherewith certifiesthat the product
BEYOND Pivoting
have been tested in an endurance test according to EuropeanEN 1154 standard. This took place in a series of exemplarytests; the fittings were mounted to a glass-door with 80 kgweight. Door width: 1000mm, door height: 2200mm.The corner patch fitting fulfils the demand given by theGerman DIN standard:
500.000 operations (cycles)
Bad Salzuflen, 28.04.2006
Dipl.-Ing.Thomas VoglerDivision GlassMechanical Design Management
DORMA-Glas GmbHMax-Planck-Str. 33-45D-32107 Bad Salzuflen
Product Certificate
DORMA-Glas GmbHherewith certifiesthat the product
Swing Door System MANET
has been tested in an durability test according to DIN EN1154.
The fittings were mounted to an exemplarily glass door of 80, 100, 120kg(plus safety multiplier) weight.
Please use a door closer type EN4 (with or without back check) or a highertype (e.g. EN5) WITHOUT back check.
This certificate applies to the following conditions/limits:
Variant Panel Weight GlassThickness Door Width Door High
Without continuouspivot bar 80kg >/=10mm </=2500mm
With continuous pivotbar and 4 single pointfixings
100kg >/=10mm </=2600mm
With continuous pivotbar and 5 single pointfixings
120kg >/=12mm
</=1200mm
</=3000mm
Using in Variant V2A Variant V4A
environments without influences of chlorideand sulphur dioxide able able
environments with moderate influences ofchloride and sulphur dioxide not able able
swimming and/or saline baths not able on enquiry
For additional technical information s please check the actual technicalprospect for DORMA-Glas.
Bad Salzuflen, 18/12/2008Dipl.-Ing.Thomas VoglerDivision GlasHead of Mechanical Design and Development
DORMA-Glas GmbHMax-Planck-Str. 33-45D-32107 Bad Salzuflen
Product Certificate
DORMA-Glas GmbHherewith certifiesthat the product
Junior Office BandHinges for/with frame pivots
has been tested according to the EN1527.The product meets the following standards:
Maximum door weight: 60kg (24mm rebate depth with sleeve and steel ball bearing)
55kg (24mm rebate depth with sleeve)
45kg (rebate depth >24mm up to 40mm)
Count of operations: class 7 (200.000 cycles)
Corrosion resistance: class 3
Glass type: TSG
Glass thickness [mm]: 8, 10
Glass surface: clear, calendered, no using of self-cleaningsurfaces (Lotus, Clear-Shield etc.)
Classification key EN1935:2 7 3 0 1 3 0 10
Bad Salzuflen, 21/04/2008
Dipl.-Ing.Thomas VoglerDivision GlasHead of Mechanical Design and Development
DORMA-Glas GmbHMax-Planck-Str. 33-45D-32107 Bad Salzuflen
Product Certificate
DORMA-Glas GmbHherewith certifiesthat the product
Junior Office hinge withsteel ball bearingArt.-Nr. 11.234
was tested according to the EN1935:2002 regarding durabilityand according to the EN1670:2007 regarding corrosionresistance with the following results:
Maximum door weight: 60kgDurability: Level 7, EN1935:2002
200.000 operationsCorrosion resistance: Level 3, EN1670:2007
Bad Salzuflen, 14.01.08
Dipl.-Ing.Thomas VoglerDivision GlasHead of Mechanical Design and Development
DORMA-Glas GmbHMax-Planck-Str. 33-45D-32107 Bad Salzuflen
Product Certificate
DORMA-Glas GmbHherewith certifiesthat the product
Junior lock
have been tested according to germanDIN 18251 standard. This took place in an endurance test.
The locking bolt fullfills the demand
50.000 operations
The ledge fullfills the demand
200.000 operations
Bad Salzuflen, 28.04.2006
Dipl.-Ing.Thomas VoglerDivision GlassMechanical Design Management
DORMA-Glas GmbHMax-Planck-Str. 33-45D-32107 Bad Salzuflen
Product Certificate
DORMA-Glas GmbHherewith certifiesthat the product
Studio lock
have been tested according to germanDIN 18251 standard. This took place in an endurance test.
The locking bolt fullfills the demand
50.000 operations
The ledge fullfills the demand
200.000 operations
Bad Salzuflen, 28.04.2006
Dipl.-Ing.Thomas VoglerDivision GlassMechanical Design Management
DORMA-Glas GmbHMax-Planck-Str. 33-45D-32107 Bad Salzuflen
Product Certificate
DORMA-Glas GmbHherewith certifiesthat the product
Door rail with BTS-insertArt.-No. 04.101
Top patchArt.-No. 03.110
has been tested in an endurance test acording to EN 1154.This took place in a series of exemplary tests; the fittings weremounted to a glassdoor with 100 kg weight.Door width: 1100mm, Door height: 2000mm.The complete door fulfils the demand
500.000 operations (cycles)
Bad Salzuflen, 28.04.2006
Dipl.-Ing.Thomas VoglerDivision GlassMechanical Design Management
DORMA-Glas GmbHMax-Planck-Str. 33-45D-32107 Bad Salzuflen
Product Certificate DORMA-Glas GmbH herewith certifies that the product
ARCOS Top Patch Fitting Art.-No. 26.110
ARCOS Bottom Patch Fitting Art.-No. 26.100 have been tested in an endurance test according to European EN 1154 standard. This took place in a series of exemplary tests; the fittings were mounted to a glass-door with 100 kg weight. Door width: 1000mm, door height: 2200mm the corner patch fitting fulfils the demand given by the German DIN standard: 500.000 operations Bad Salzuflen, 21.06.2007 Dipl.-Ing.
Thomas Vogler Division Glass Mechanical Design Management
DORMA-Glas GmbH Max-Planck-Str. 33-45 D-32107 Bad Salzuflen
Product Certificate DORMA-Glas GmbH herewith certifies that the product
Top Patch Fitting Art.-No. 03.110
Bottom Patch Fitting Art.-No. 03.100 has been tested in an durability test according to DIN EN 1154. The fittings were mounted to an exemplarily glass door of 130 kg (plus safety multiplier) weight. This certificate applies to the following conditions/limits:
• count of operations: </= 500.000
• door width </= 1.300mm
• door height </= 2.500mm For doors with more than 100kg weight please use a door closer type EN4 (with or without back check) or a higher type (e.g. EN5) WITHOUT back check. For doors with a height of more than 2.500mm additional the following conditions/limits has to be observed:
• glass thickness >/= 10mm
• Usage of a handle bar with 3 connection points in minimum and a minimum height of 2/3 door height.
Bad Salzuflen, 1/25/2008 Dipl.-Ing.
Thomas Vogler Division Glass Mechanical Design Management
DORMA-Glas GmbH Max-Planck-Str. 33-45 D-32107 Bad Salzuflen
Product Certificate
DORMA-Glas GmbHherewith certifiesthat the product
Overpanel Patch FittingArt.-No. 03.120
has been tested in an endurance test according to EN 1154a glassdoor of 101 kg weight was fitted with PT10/PT 20,attached to 2 x PT 30 with wall bracket Art.-No. 01.127 onwall. Overpanel fixed to ceiling with wall connecting profileArt.-No. 07.042.
The fittings fulfilled the demand
500.000 operations
Bad Salzuflen, 28.04.2006
Dipl.-Ing.Thomas VoglerDivision GlassMechanical Design Management
DORMA-Glas GmbHMax-Planck-Str. 33-45D-32107 Bad Salzuflen
Product Certificate
DORMA-Glas GmbHherewith certifiesthat the product
Overpanel and Sidepanel PatchFittingArt.-No. 03.140
has been tested in an endurance test according to EN 1154.a glassdoor of 101 kg weight was fitted with PT10/PT 20,attached to a PT 40 on pirot side and a PT 30 on lock side. PT30 fixed to wall with bracket Art.-No. 01.127. Overpanel fixedto ceiling with wall connection profile Art.-No. 07.042.
The fittings fulfilled the demand
500.000 operations
Bad Salzuflen, 28.04.2006
Dipl.-Ing.Thomas VoglerDivision GlassMechanical Design Management
DORMA-Glas GmbHMax-Planck-Str. 33-45D-32107 Bad Salzuflen
Product CertificateDORMA-Glas GmbHherewith certifiesthat the product
DORMA-SMType 1010 1046Latest drawing revision 2005
has been tested in an durability test according to EN1154.
The fittings were mounted to an exemplarily glass door of 80kg(safety multiplier not included) weight.
This certificate applies to the following conditions/limits:
· count of operations: </= 200.000· door width </= 1.100mm· door height </= 2.300mm· door weight </= 80kg
After 200.000 operations all installed parts have to be checkedaccording the following items:
· mechanical fractures· screw torques· precise position of the fittings
Please use a door closer type EN4 only.
Further technical information are given in technical documentation.
Bad Salzuflen, 16/01/2009
Dipl.-Ing.Thomas VoglerDivision GlassHead of Mechanical Design and Development
DORMA-Glas GmbHMax-Planck-Str. 33-45D-32107 Bad Salzuflen
Recommended