View
7
Download
0
Category
Preview:
Citation preview
POWER CAGE CLAMP®High-Current Terminal Blocks for Conductors up to 350 kcmil (185 mm2)
vibration-proof – fast – maintenance-free
© WAGO
Using springs instead of screws is the key to WAGO’s success. The POWER CAGE CLAMP® provides the appropriate clamping force for conductors up to 2, 2/0, 4/0 AWG and 350 kcmil (35, 50, 95 and 185 mm2).
BENEFITS
The Latest and Largest Member of our High-Current Family Connects:
• 1/0 to 350 kcmil• 310 A• Up to 1000 VAC/DC
For more information visitwww.wago.us/sccr
2
Fast Termination
• Eliminate time-consuming preparation – no ring terminals or ferrules required
• No expensive torque wrenches or calibration required
• Up to 60% faster than wiring with screw terminal blocks
Easy to Use
• Side conductor entry • Orange locking tab keeps the
clamp open for hands-free wiring• Industry’s widest range of
accessories to get the job done
• No retightening of screws – wire it once and forget it
Vibration-Proof – Fast – Maintenance-Free
Always Reliable
• Optimum clamping force – independent of operator skill
• 100% reliable with vibration-proof, thermal cycling resistant, gas-tight connections
Suitable for Every Application
• Meets the most stringent requirements, including those specified for railway and marine applications.
• Heat- and cold-resistant – even under the heaviest of loads
3
Grounding
• Green/yellow terminal blocks easily identify ground function
• Metal snap-on mounting foot ensures the proper ground connection without the use of screws.
Marking
• Continuous marking strip installed with a quick swipe of the thumb
• Marking tags installed individually above the orange locking tab
• Marking carrier supplements the use of tag and strip marking
Continuous Marking Strip
Marking Tags
Conductor Termination
Rotate the operating tool counterclockwise to the stop !. Next, push in the orange locking tab for hands-free wiring.
Insert a stripped conductor until it hits the backstop. Hold in this position.
A short counter-clockwise rotation " releases the tab. The operating tool then rotates clockwise, securely clamping the conductor.
OUR POWER TEAMTerminate Conductors up to 350 kcmil (185 mm2) with Just One Turn
4
Power Tap (for 2 AWG … 350 kcmil)
• Easy to install, space saving power tap, with marking tag holder, allows for convenient power distribution to additional loads
Safety
Protective Warning Covers • Provides visual indication for
high-voltage applications and prevents access to conductor clamping mechanism as well as built-in test point
Finger Guards • Yellow, detachable shock
protectors for unused jumper slots or conductor entries
Commoning Testing
For 2 AWGConvenient push-in adjacent jumper allows for easy potential commoning. Independent jumper slots allow continuous commoning beyond two terminal blocks.
For 2/0, 4/0 and 350 kcmil
Comb style jumper provides convenient potential commoning. Dual jumper slot allows for max rated conductor ‒ no conductor size derating required. .
Via Step-Down Jumpers with TOPJOB® SPush-in, step-down jumper offers easy power distribution from 2 AWG (POWER CAGE CLAMP®) to 20-4 AWG (2010 - 2016 Series TOPJOB®S terminal blocks).
Easy troubleshooting via 4 mm Ø touch-proof test plug.Use a test plug adapter (283-404) for 2 AWG terminal blocks.
5
2 AWG (35 mm2) 2/0 AWG (50 mm2) 4/0 AWG (95 mm2) 350 kcmil (185 mm2)
Conductor cross-section
Rated voltage/current
Terminal block widthStrip length
10 … 2 AWG(6 … 35 mm2)
600 V, 115 A U600 V, 115 A 21000 V, 125 A EN
16 mm/0.63 in.L 25 mm/0.98 in.
10 … 2 AWG(6 … 35 mm2) 600 V, 115 A U600 V, 115 A 21000 V, 125 A EN
16 mm/0.63 in.L 25 mm/0.98 in.
8 … 2/0 AWG(10 … 50 (70 “f-st”) mm2) 600 V, 150 A U600 V, 150 A 21000 V, 150 A EN
20 mm/0.79 in.L 30 mm/1.18 in.
8 … 2/0 AWG(10 … 50 (70 “f-st”) mm2) 600 V, 150 A U600 V, 150 A 21000 V, 150 A EN
20 mm/0.79 in.L 30 mm/1.18 in.
4 … 4/0 AWG(25 … 95 mm2) 600 V, 200 A U600 V, 200 A 21000 V, 232 A EN
25 mm/0.98 in.L 35 mm/1.38 in.
4 … 4/0 AWG(25 … 95 mm2) 600 V, 200 A U600 V, 200 A 21000 V, 232 A EN
25 mm/0.98 in.L 35 mm/1.38 in.
1/0 AWG … 350 kcmil(50 … 185 mm2 )
1000 V, 310 A U1000 V, 310 A 21000 V, 353 A EN
32 mm/1.26 in.L 45 … 47 mm/1.77 … 1.85 in
1/0 AWG … 350 kcmil(50 … 185 mm2 )
1000 V, 310 A U1000 V, 310 A 21000 V, 353 A EN
32 mm/1.26 in.L 45 … 47 mm/1.77 … 1.85 in
Image
Item Numbers
2-conductor through terminal block
285-135 285-134 285-935 1
Only suitable for DIN 35 x 15 rails
2-conductor ground terminal block
285-137 285-137/999-950 1
Only suitable for DIN 35 x 15 rails; 2.3 mm thick
2-conductor through terminal block
285-150 285-154 285-950 1
Only suitable for DIN 35 x 15 rails
2-conductor ground terminal block
285-157 285-157/999-950 1
Only suitable for DIN 35 x 15 rails; 2.3 mm thick, copper
2-conductor through terminal block
285-195 285-194 285-995 1
Only suitable for DIN 35 x 15 rails
2-conductor ground terminal block
285-197 285-197/999-950 1
Only suitable for DIN 35 x 15 rails; 2.3 mm thick, copper
2-conductor through terminal block
285-1185 285-1184 285-1189 * 1
Only suitable for DIN 35 x 15 rails
2-conductor ground terminal block
285-1187 285-1187/999-950 * 1Only suitable for DIN 35 x 15 rails; 2.3 mm thick, copper
Accessories
Adjacent jumper
285-435 (lN 85 A) 285-450 (lN 150 A for 1 jumper, lN 130 A for 2 … 4 jumpers)
285-495 (lN 232 A for 1 jumper, lN 192 A for 2 … 4 jumpers) 285-1171 (lN 309 A for 1 jumper)
Step-down jumper 285-430 (lN 90 A) – – –
Power tap
285-427 (1x24 ... 10 AWG)(600 V, 30 A U / 800 V, 32 A EN)
285-447 (2x24 ... 10 AWG)(600 V, 30 A U / 1000 V, 41 A EN)
285-407 (2x24 ... 8 AWG)(600 V, 50 A U / 1000 V, 57 A EN)
285-1175 (1x24 ... 8 AWG)(600 V, 50 A U / 1000 V, 57 A EN)
Warning cover 285-420 285-440 285-170 285-1177
Finger guard 285-421 285-441 285-169 285-1178
Operating tool 210-721 (type 3, 5.5 x 0.8 mm screwdriver blade) 285-172 (Allen-wrench) 285-172 (Allen-wrench) 285-172 (Allen-wrench)
Marking Accessories
Marking strips 2009-110 (plain, white, 11 mm wide, 50 m reel) 2009-110 (plain, white, 11 mm wide, 50 m r eel)Requires use of marker carrier
2009-110 (plain, white, 11 mm wide, 50 m reel)Requires use of marker carrier 2009-110 (plain, white, 11 mm wide, 50 m reel)
WMB Inline markers 2009-115 (plain, white, 1500 markers, stretchable 5 … 5.2 mm) 2009-115 (plain, white, 1500 markers, str etchable 5 … 5.2 mm) 2009-115 (plain, white, 1500 markers, stretchable 5 … 5.2 mm) 2009-115 (plain, white, 1500 markers, stretchable 5 … 5.2 mm)
WMB Multi marking system 793-5501 (plain, white, 10 strips with 10 markers per card, stretchable 5 … 5.2 mm)
793-5501 (plain, white, 10 strips with 10 m arkers per card, stretchable 5 … 5.2 mm)
793-5501 (plain, white, 10 strips with 10 markers per card, stretchable 5 … 5.2 mm)
793-5501 (plain, white, 10 strips with 10 markers per card, stretchable 5 … 5.2 mm)
Marker carrier 285-442 285-442 285-442 –
285 SERIES
6
2 AWG (35 mm2) 2/0 AWG (50 mm2) 4/0 AWG (95 mm2) 350 kcmil (185 mm2)
Conductor cross-section
Rated voltage/current
Terminal block widthStrip length
10 … 2 AWG(6 … 35 mm2)
600 V, 115 A U600 V, 115 A 21000 V, 125 A EN
16 mm/0.63 in.L 25 mm/0.98 in.
10 … 2 AWG(6 … 35 mm2) 600 V, 115 A U600 V, 115 A 21000 V, 125 A EN
16 mm/0.63 in.L 25 mm/0.98 in.
8 … 2/0 AWG(10 … 50 (70 “f-st”) mm2) 600 V, 150 A U600 V, 150 A 21000 V, 150 A EN
20 mm/0.79 in.L 30 mm/1.18 in.
8 … 2/0 AWG(10 … 50 (70 “f-st”) mm2) 600 V, 150 A U600 V, 150 A 21000 V, 150 A EN
20 mm/0.79 in.L 30 mm/1.18 in.
4 … 4/0 AWG(25 … 95 mm2) 600 V, 200 A U600 V, 200 A 21000 V, 232 A EN
25 mm/0.98 in.L 35 mm/1.38 in.
4 … 4/0 AWG(25 … 95 mm2) 600 V, 200 A U600 V, 200 A 21000 V, 232 A EN
25 mm/0.98 in.L 35 mm/1.38 in.
1/0 AWG … 350 kcmil(50 … 185 mm2 )
1000 V, 310 A U1000 V, 310 A 21000 V, 353 A EN
32 mm/1.26 in.L 45 … 47 mm/1.77 … 1.85 in
1/0 AWG … 350 kcmil(50 … 185 mm2 )
1000 V, 310 A U1000 V, 310 A 21000 V, 353 A EN
32 mm/1.26 in.L 45 … 47 mm/1.77 … 1.85 in
Image
Item Numbers
2-conductor through terminal block
285-135 285-134 285-935 1
Only suitable for DIN 35 x 15 rails
2-conductor ground terminal block
285-137 285-137/999-950 1
Only suitable for DIN 35 x 15 rails; 2.3 mm thick
2-conductor through terminal block
285-150 285-154 285-950 1
Only suitable for DIN 35 x 15 rails
2-conductor ground terminal block
285-157 285-157/999-950 1
Only suitable for DIN 35 x 15 rails; 2.3 mm thick, copper
2-conductor through terminal block
285-195 285-194 285-995 1
Only suitable for DIN 35 x 15 rails
2-conductor ground terminal block
285-197 285-197/999-950 1
Only suitable for DIN 35 x 15 rails; 2.3 mm thick, copper
2-conductor through terminal block
285-1185 285-1184 285-1189 * 1
Only suitable for DIN 35 x 15 rails
2-conductor ground terminal block
285-1187 285-1187/999-950 * 1Only suitable for DIN 35 x 15 rails; 2.3 mm thick, copper
Accessories
Adjacent jumper
285-435 (lN 85 A) 285-450 (lN 150 A for 1 jumper, lN 130 A for 2 … 4 jumpers)
285-495 (lN 232 A for 1 jumper, lN 192 A for 2 … 4 jumpers) 285-1171 (lN 309 A for 1 jumper)
Step-down jumper 285-430 (lN 90 A) – – –
Power tap
285-427 (1x24 ... 10 AWG)(600 V, 30 A U / 800 V, 32 A EN)
285-447 (2x24 ... 10 AWG)(600 V, 30 A U / 1000 V, 41 A EN)
285-407 (2x24 ... 8 AWG)(600 V, 50 A U / 1000 V, 57 A EN)
285-1175 (1x24 ... 8 AWG)(600 V, 50 A U / 1000 V, 57 A EN)
Warning cover 285-420 285-440 285-170 285-1177
Finger guard 285-421 285-441 285-169 285-1178
Operating tool 210-721 (type 3, 5.5 x 0.8 mm screwdriver blade) 285-172 (Allen-wrench) 285-172 (Allen-wrench) 285-172 (Allen-wrench)
Marking Accessories
Marking strips 2009-110 (plain, white, 11 mm wide, 50 m reel) 2009-110 (plain, white, 11 mm wide, 50 m r eel)Requires use of marker carrier
2009-110 (plain, white, 11 mm wide, 50 m reel)Requires use of marker carrier 2009-110 (plain, white, 11 mm wide, 50 m reel)
WMB Inline markers 2009-115 (plain, white, 1500 markers, stretchable 5 … 5.2 mm) 2009-115 (plain, white, 1500 markers, str etchable 5 … 5.2 mm) 2009-115 (plain, white, 1500 markers, stretchable 5 … 5.2 mm) 2009-115 (plain, white, 1500 markers, stretchable 5 … 5.2 mm)
WMB Multi marking system 793-5501 (plain, white, 10 strips with 10 markers per card, stretchable 5 … 5.2 mm)
793-5501 (plain, white, 10 strips with 10 m arkers per card, stretchable 5 … 5.2 mm)
793-5501 (plain, white, 10 strips with 10 markers per card, stretchable 5 … 5.2 mm)
793-5501 (plain, white, 10 strips with 10 markers per card, stretchable 5 … 5.2 mm)
Marker carrier 285-442 285-442 285-442 –
1 These items have hazardous locations approvals - IECEx, ATEX, UL, Class 1, Zone 0 For more technical data, see our Full Line Catalog, Volume 1, or visit www.wago.us * Pending
7
© WAGO
WAGO’s 350 kcmil (185 mm²) high-current, rail-mounted terminal blocks are also available with mounting flanges for direct installation on a sub-panel or mounting plate.
This version shares the same accessories with the 350 kcmil rail-mount terminal blocks.
350 kcmil BLOCK WITH MOUNTING FLANGES
For more information visitwww.wago.us/sccr
8
Mount a 350 kcmil terminal block directly onto the plate via screw-type flanges.
Vibration-Proof – Fast – Maintenance-Free
Nominal current: 310 A Rated voltage: up to 1000 VAC/DC
Versions for functional ground in gray-yellow housing
9
First, insert block-to-block connectors (285-1179) into housing slots.
1.
2.
3. Secure the terminal block to a mounting plate using two M8 cylinder-head screws and appropriate washers.
Then, connect and align the terminal blocks.
INSTALLATION
The Panel Mount Version is the Newest Edition to our POWER CAGE CLAMP®family, offering:
• The same reliable, vibration-proof, and maintenance-free connection as the DIN-rail mount POWER CAGE CLAMP®
10
285 SERIES WITH MOUNTING FLANGES
350 kcmil (185 mm²)
Conductor cross-section
Rated voltage/current
Terminal block width Strip length
1/0 AWG … 350 kcmil(50 … 185 mm2 )
1000 V, 310 A U1000 V, 310 A 21000 V, 353 A EN pending
32 mm/1.26 in.L 45 … 47 mm/1.77 … 1.85 in.
1/0 AWG … 350 kcmil(50 … 185 mm2 )
1000 V, 310 A U1000 V, 310 A 21000 V, 353 A EN
32 mm/1.26 in.L 45 … 47 mm/1.77 … 1.85 in.
Image
Item Numbers
2-conductor through terminal block with screw flanges
285-1161 285-1164 285-1163 1
2-conductor through terminal block with screw flanges
285-1167 285-1167/999-950* 1
Accessories
Adjacent jumper 285-1171 (lN 309 A for 1 jumper)
Power tap 285-1175 (2x24 ... 8 AWG)(600 V, 50 A U / 1000 V, 57 A EN)
Block-to-block connectorIMAGE?
285-1179
Warning cover 285-1177
Finger guard 285-1178
Operating tool 285-172
Marking Accessories
Marking strips 2009-110 (plain, white, 11 mm wide, 50 m reel)
WMB Inline markers 2009-115 (plain, white, 1500 markers, stretchable 5 … 5.2 mm)
WMB Multi marking system 793-5501 (plain, white, 10 strips with 10 markers per card, stretchable 5 … 5.2 mm)
1 These items have hazardous locations approvals - IECEx, ATEX, UL, Class 1, Zone 0 For more technical data, see our Full Line Catalog, Volume 1, or visit www.wago.us * Pending
11
6031
8567
– 0
888-
1583
/010
0-69
45 –
185
MM
² PO
WER
CC
1.1
US
– 09
/201
6 –
Prin
ted
in th
e Un
ited
Stat
es –
Sub
ject
to d
esig
n ch
ange
s
MexicoWAGO CorporationQueretaroTel. 001/800/309/5975 + 52/442/221/5946Fax + 52/442/221/5063 www.wago.mx
WAGO CorporationN120 W19129 Freistadt RoadGermantown, Wisconsin 53022Telephone: 800 / DIN Rail (346-7245)Fax: 262 / 255-3232info.us@wago.comwww.wago.us
CanadaWAGO CorporationTel. 800/DIN Rail (346-7245)Fax 262/255-3232www.wago.ca
WAGO is a registered trademark of WAGO Verwaltungsgesellschaft mbH.”Copyright – WAGO Kontakttechnik GmbH & Co. KG – all rights reserved. The content and structure of the WAGO Websites, catalogs, videos, and other WAGO media are subject to copyright. The dissemination or changing of the content of these pages and videos is not permitted. Furthermore, the content may neither be copied nor made available to third parties for commercial purposes. Also subject to copyright are the images and videos that were made available to WAGO Kontakttechnik GmbH & Co. KG by third parties.”
Recommended