Module 3 Configuring Hardware on a Computer Running Windows XP Professional

Module 3Configuring Hardware on a Computer Running Windows XP Professional

Introduction• Hardware

– Plug and play– Non plug and play

• Software– Operating system– Applications– Drivers

• signed device driver• Unsigned device driver

• Firmware

System Resources

• IRQ - Interrupt Requests• Input/output (I/O) port

addresses• Memory addresses• DMA -Direct Memory Access

jumpers

Installing Plug and Play Devices

• Cheek Hardware Compatibility List (HCL).

• logged on as Administrator or a member of the local Administrators group.

• An exception to this requirement is when you are installing a local printer.

• Device types– For USB, IEEE 1394 , SCSI just plug in the

device. Detection is automatic.– For PCI and ISA turn the computer off,

note

• If a Plug and Play device, such as a CD-RW (compact disc.read write) drive, has been installed and then removed from a computer running Windows XP Professional, the device configuration and drivers remain on the computer. Reconnecting the same device can be done by any end user and does not require reinstallation by an administrator. This enables users to easily share devices.

Installing Non–Plug and Play Devices

• Connect the device to the appropriate port, or insert the device into a slot on your computer, according to the device manufacturers instructions.

• Use the Add Hardware Wizard to identify the type of device that you are installing.

• Insert the Windows XP Professional installation CD or the manufacturers disk so that Windows XP Professional can load the proper device drivers.

• After you load the device drivers onto your system, Windows XP Professional configures the properties and settings for the device.

• If instructed by the setup program or documentation, you may need to configure the resources manual

Viewing Installed DevicesDevice treeDevice node.

You can use Device Manager to:

• Determine whether the hardware on your computer is working properly.

• Change hardware configuration settings. • Identify the device drivers that are

loaded for each device, and obtain information about each device driver.

• Install updated device drivers. • Disable, enable, and uninstall devices. • Roll back to the previous version of a

driver. • Print a summary of the devices that are

installed on your computer

Working with Drivers

• Driver Signing• Updating Drivers• Driver Rollback

Driver Signing

Identifying unsigned files sigverif

Procedure to updatedrivers

Hardware IDs

Driver Rollback•Driver rollback will not be an available option if a driver has not been updated

•Driver rollback is available for any device except printers.

•Reinstallbackups folder

%systemroot%\system32\reinstallbackupsis created the first time a user updates an existing driver package*.INF *.SYS

Troubleshooting Hardware Devices

Using Device Manager to Troubleshoot Devices

Viewing hidden devices

• Device Manager does not display all devices by default.

• Certain non Plug and Play devices and devices that were previously attached to the computer are hidden.

• You can set Device Manager to allow you to view currently attached hidden devices, to review device status, or to troubleshoot problems.

Removing Devices

• Devices that are designed to Devices that are designed to be removed while the system be removed while the system is turned on are:is turned on are:

• All USB devices.• IEEE 1394 devices, except

removable storage devices.• PC Card devices.• CardBus devices.

PC Card devices & CardBus devices

Impact of surprise removal

Removable storage devices.Removable storage devices.can cause data loss or data corruption.PC Card, CardBus Card, parallel and PC Card, CardBus Card, parallel and COM port devices.COM port devices.Can cause the system to stopApplications.Applications.Applications that are running might stop responding or .hang. as a result of a surprise removal.

Configuring Resources

Procedure to create ahard copy of deviceresource settings report

Restoring resources tooriginal settings

Adding a Local Printer

Printing preferences

Adding a Local Printer

• To install a local printer by using the To install a local printer by using the Add Printer Wizard:Add Printer Wizard:

1. Open Control Panel, click Printers and Other Hardware, and then click Printers and Faxes.

2. Under Printer Tasks, click Add a Printer, and then follow the instructions.

• The minimum permission Power Users. • Device Manager does not enable you to

manage or configure local printers. It does provide capabilities to manage the printer ports, but not the printer directly.

Supporting Bluetooth Devices

Introduction• Bluetooth wireless technology is a

low-cost, short-range wireless specification for connecting mobile devices and is available on a wide variety of devices.

Bluetooth Devices in Control Panel

Bluetooth icon in the taskbar

Network Connectionschanges

Bluetooth File Transfer wizard

Procedure to allow a Bluetooth device to find

your computer

Configuring Multiple Monitors

introduction

• Using multiple monitors is desirable for users who work with multiple applications and need to view the interfaces of these applications simultaneously.

• By using multiple monitors, you can configure up to 10 monitors

Configuring multiplemonitors

• Have an installed PCI or AGP device.

• Run in graphical user interface (GUI)

• Have a Windows XP Professional driver that enables a secondary display.

Procedure for installingadditional monitors

1. Turn off your computer.2. Insert your additional PCI or AGP video adapter into an

available slot.3. Plug your additional monitor into the card.4. Turn on your computer. Windows XP Professional will detect

the new video5. adapter and install the appropriate drivers.6. Open Control Panel, and then double-click Display.7. On the Settings tab, click the monitor icon that represents the

monitor that you want to use in addition to your primary monitor.

8. Select the Extend my Windows desktop onto this monitor check box, and

9. then click Apply.10.Select the color depth and resolution for the secondary display.11.Repeat steps 6 through 8 for each additional display, and then

click OK to close the Display Properties sheet.

• Procedure for changing the primary monitor

• Arranging multiple monitors• How to move items from one

monitor to another

The end