View
594
Download
24
Category
Tags:
Preview:
DESCRIPTION
List of All NDT DIN Standard
Citation preview
List of DIN standardsFrom Wikipedia, the free encyclopedia
Jump to: navigation, search
This is an incomplete list of DIN standards.
The "STATUS" column gives the latest known status of the standard. o If a standard has been withdrawn and no replacement specification is listed, either
the specification was withdrawn without replacement or a replacement specification could not be identified.
DIN standards that begin with "DIN V" ("Vornorm", meaning "pre-issue") are the result of standardization work, but because of certain reservations on the content or because of the divergent compared to a standard installation procedure of DIN, they are not yet published standards.
Contents
[hide]
1 DIN 1 to DIN 999 o 1.1 DIN 1 to DIN 99 o 1.2 DIN 100 to DIN 199 o 1.3 DIN 200 to DIN 299 o 1.4 DIN 300 to DIN 399 o 1.5 DIN 400 to DIN 499 o 1.6 DIN 500 to DIN 599 o 1.7 DIN 600 to DIN 699 o 1.8 DIN 700 to DIN 799 o 1.9 DIN 800 to DIN 899 o 1.10 DIN 900 to DIN 999
2 DIN 1000 to DIN 9999 o 2.1 DIN 1000 to DIN 1999 o 2.2 DIN 2000 to DIN 2999 o 2.3 DIN 4000 to DIN 4999 o 2.4 DIN 5000 to DIN 5999 o 2.5 DIN 6000 to DIN 6999 o 2.6 DIN 7000 to DIN 7999 o 2.7 DIN 8000 to DIN 8999 o 2.8 DIN 9000 to DIN 9999
3 DIN 10000 to DIN 19999 o 3.1 DIN 10000 to DIN 10999 o 3.2 DIN 11000 to DIN 11999
o 3.3 DIN 12000 to DIN 12999 o 3.4 DIN 13000 to DIN 13999 o 3.5 DIN 14000 to DIN 14999 o 3.6 DIN 15000 to DIN 15999 o 3.7 DIN 16000 to DIN 16999 o 3.8 DIN 17000 to DIN 17999 o 3.9 DIN 18000 to DIN 18999 o 3.10 DIN 19000 to DIN 19999
4 DIN 20000 to DIN 29999 o 4.1 DIN 24000 to DIN 24999 o 4.2 DIN 28000 to DIN 28999
5 DIN 30000 to DIN 39999 o 5.1 DIN 31000 to DIN 31999
6 DIN 40000 to DIN 49999 7 DIN 50000 to DIN 59999 8 DIN 60000 to DIN 69999 9 DIN 70000 to DIN 79999 10 External links
[edit] DIN 1 to DIN 999
[edit] DIN 1 to DIN 99
DIN TITLE STATUS DIN REPLACEMENT OTHER ORG
REPLACEMENT
DIN 1Cone Pins, untempered
Withdrawn DIN EN 22339 ISO 2339
DIN 3Standard measurements
Withdrawn
DIN 5
Technical drawings - Axonometric projections, Isometric projection
Withdrawn
DIN ISO 5456-1, DIN ISO 5456-2,DIN ISO 5456-3, DIN ISO 5456-4
ISO 5456-1, ISO 5456-2,ISO 5456-3, ISO 5456-4
DIN 5-10 Technical Withdrawn DIN ISO 10209-2 ISO 10209-2
drawings - projections, terms
DIN 6
Projection displays in Normal, views and special presentations
Withdrawn DIN ISO 128, DIN EN ISO 128 ISO 128
DIN 7 Parallel Pins Withdrawn DIN EN 22338 ISO 2338
DIN 11
Whitworth pipe threads 1/4"-6" Thread diameter, sizes, teaching information
Withdrawn
DIN 13-1
ISO general purpose metric screw threads - Part 1: Nominal sizes for coarse pitch threads; nominal diameter from 1 mm to 68 mm
Active
DIN 13-2 ISO general purpose metric screw threads - Part 2: Nominal sizes for 0,2
Active
mm, 0,25 mm and 0,35 mm fine pitch threads; nominal diameter from 1 mm to 50 mm
DIN 13-3
ISO general purpose metric screw threads - Part 3: Nominal sizes for 0,5 mm fine pitch threads; nominal diameter from 3,5 mm to 90 mm
Active
DIN 13-4
ISO general purpose metric screw threads - Part 4: Nominal sizes for 0,75 mm fine pitch threads; nominal diameter from 5 mm to 110 mm
Active
DIN 13-5 ISO general purpose metric screw threads - Part 5: Nominal sizes for 1 mm and 1,25 mm fine pitch
Active
threads; nominal diameter from 7,5 mm to 200 mm
DIN 13-6
ISO general purpose metric screw threads - Part 6: Nominal sizes for 1,5 mm fine pitch threads; nominal diameter from 12 mm to 300 mm
Active
DIN 13-7
ISO general purpose metric screw threads - Part 7: Nominal sizes for 2 mm fine pitch threads; nominal diameter from 17 mm to 300 mm
Active
DIN 13-8 ISO general purpose metric screw threads - Part 8: Nominal sizes for 3 mm fine pitch threads; nominal diameter from 28 mm to 300
Active
mm
DIN 13-9
ISO general purpose metric screw threads - Part 9: Nominal sizes for 4 mm fine pitch threads; nominal diameter from 40 mm to 300 mm
Active
DIN 13-10
ISO general purpose metric screw threads - Part 10: Nominal sizes for 6 mm fine pitch threads; nominal diameter from 70 mm to 500 mm
Active
DIN 13-11
ISO general purpose metric screw threads - Part 11: Nominal sizes for 8 mm fine pitch threads; nominal diameter from 130 mm to 1000 mm
Active
DIN 13-12
ISO general purpose metric screw threads - Part 12: 1 to 300 mm diameter coarse and fine pitch threads Selected diameters and pitches
Active
DIN 13-13
ISO general purpose metric screw threads - Part 13: Selected sizes for screws, bolts and nuts from 1 to 52 mm screw thread diameter and limits of sizes
Active
DIN 13-19
ISO general purpose metric screw threads - Part 19: Nominal profiles
Active
DIN 13-20
ISO general purpose metric screw threads - Part 20: Limits of sizes for coarse pitch threads with the preferred tolerance
Active
classes; nominal sizes from 1 mm to 68 mm
DIN 13-21
ISO general purpose metric screw threads - Part 21: Limits of sizes for fine pitch threads with the preferred tolerance classes; Nominal diameter from 1 mm to 24,5 mm
Active
DIN 13-22
ISO general purpose metric screw threads - Part 22: Limits of sizes for fine pitch threads with the preferred tolerance classes; Nominal diameter from 25 mm to 52 mm
Active
DIN 13-23
ISO general purpose metric screw threads - Part 23: Limits of sizes for fine
Active
pitch threads with the preferred tolerance classes; Nominal diameter from 53 mm to 110 mm
DIN 13-24
ISO general purpose metric screw threads - Part 24: Limits of sizes for fine pitch threads with the preferred tolerance classes; Nominal diameter from 112 mm to 180 mm
Active
DIN 13-25
ISO general purpose metric screw threads - Part 25: Limits of sizes for fine pitch threads with the preferred tolerance classes; Nominal diameter from 182 mm to 250 mm
Active
DIN 13-26
ISO general purpose metric screw threads - Part 26: Limits of sizes for fine pitch threads with the preferred tolerance classes; Nominal diameter from 252 mm to 1000 mm
Active
DIN 13-28
ISO general purpose metric screw threads - Part 28: Coarse and Fine Screw Threads from 1 to 250 mm Screw Thread Diameter; Root Cross-sections, Tensile Stress Cross-sections and Pitch Angles
Active
DIN 13-50
ISO general purpose metric screw threads - Part 50: Combination of tolerance classes for formed internal screw
Active
threads
DIN 13-51
ISO general purpose metric screw threads - Part 51: External screw threads for transition fits (former: screw threads for interference fit); tolerances, limit deviations, limits of sizes
Active
DIN 13-52
ISO general purpose metric screw threads - Part 52: Multi-start thread tolerances and deviation of profile
Active
DIN 76-1
Thread run-outs and thread undercuts for ISO metric threads in accordance with DIN 13-1
Active
DIN 76-2 Thread run-outs and thread
Active
undercuts for pipe threads conforming to ISO 228 part 1
DIN 76-3
Runouts, Undercuts for Trapezoidal Threads, Buttress Threads and Knuckle Threads and other Threads of Coarse Pitch
Active
DIN 78Protrusions of bolt ends
ActiveDIN EN ISO 4753 (governs thread ends for bolts assembled with hexagon slotted nuts)
ISO 4753
DIN 84
Product grade A slotted cheese head screws
Withdrawn DIN EN ISO 1207 ISO 1207
DIN 85Product grade A slotted pan head screws
Withdrawn DIN EN ISO 1580 ISO 1580
DIN 93Tab washers with long tab
Withdrawn DIN EN ISO 1234 ISO 1234
DIN 94 Split pins Withdrawn DIN EN ISO 1234 ISO 1234
DIN 95 Slotted Raised Countersunk
Active
(Oval) Head Wood Screws
DIN 96Slotted Round Head Wood Screws
Active
[edit] DIN 100 to DIN 199
DIN TITLE STATUS DIN REPLACEMENT OTHER ORG
REPLACEMENT
DIN V 105-1
Clay masonry units - Part 1: Solid and hollow bricks with density classes of 1,2
WithdrawnDIN V 105-100, DIN EN 771-1
EN 771-1
DIN V 105-2
Clay masonry units - Part 2: Solid and hollow bricks with density classes equal 1.0
WithdrawnDIN V 105-100, DIN EN 771-1
EN 771-1
DIN 105-3 Clay masonry units - Part 3: Tile and high strength-high-strength
Withdrawn DIN V 105-100, DIN EN 771-1
EN 771-1
clinker
DIN 105-4
Clay masonry units - Part 4: Ceramic bricks
WithdrawnDIN V 105-100, DIN EN 771-1,DIN EN 772-7
EN 771-1, EN 772-7
DIN 105-5
Clay masonry units - Part 5: Lightweight long-hole brick and light long-hole brick panels
Active
DIN V 105-6
Clay masonry units - Part 6: High precision units
Active
DIN V 105-100
Clay masonry units - Part 100: Clay masonry units with specific properties
Active
DIN 125 Washers; medium type, primarily for hexagon
Withdrawn DIN EN ISO 7089,DIN EN ISO 7090
ISO 7089,ISO 7090
bolts
DIN 125-1
Product grade A washers - with a hardness up to 250 HV designed for use with hexagon head bolts and nuts
WithdrawnDIN EN ISO 7089,DIN EN ISO 7090
ISO 7089,ISO 7090
DIN 125-2
Product grade A washers - with a hardness up to 300 HV designed for use with hexagon head bolts and nuts
WithdrawnDIN EN ISO 7089,DIN EN ISO 7090
ISO 7089,ISO 7090
DIN 126
Product grade C washers - designed for use with hexagon head bolts and nut
Withdrawn DIN EN ISO 7091 ISO 7091
DIN 127
Spring lock washers with square ends or tang ends
Withdrawn
DIN 128
Curved and wave spring lock washers
Withdrawn
DIN 137
Spring washers, curved or wave
Withdrawn
[edit] DIN 200 to DIN 299
DIN TITLE STATUS DIN
REPLACEMENT OTHER ORG
REPLACEMENT
DIN 201
Technical drawings; Hatchings; Representation of cutting edges and materials
Withdrawn DIN ISO 128-50 ISO 128-50
DIN 209
Machine Reamers with Screwed-on Blades
Active
DIN 267-1
Fasteners - Part 1: Technical delivery conditions; General requirements
Withdrawn
DIN 267-2 Fasteners - Part 2: Technical
Active DIN EN ISO 4759-1 ISO 4759-1
delivery conditions; Bolts, Screws, Nuts and Similar Threaded and Formed Parts; Types and Dimensional Accuracy
DIN 267-3
Fasteners - Part 3: Technical delivery conditions; Property classes for carbon steel and alloy steel bolts and screws; Conversion of property classes
Withdrawn DIN EN ISO 898-1 ISO 898-1
DIN 267-4
Fasteners - Part 4: Technical delivery conditions; Property classes for nuts (previous classes)
Withdrawn DIN EN ISO 898-2 ISO 898-2
DIN 267-5 Fasteners – Part 5: Technical delivery conditions; Acceptance inspection;
Withdrawn DIN EN ISO 3269 ISO 3269
modified version of ISO 3269, 1984 edition
DIN 267-6
Fasteners - Part 6: Technical delivery conditions; Designs and accuracy of measurement for product grade F
Active
DIN 267-7
Fasteners - Part 9: Technical delivery conditions; Bolts made of unalloyed or low-alloy steels
Withdrawn DIN EN ISO 898-1 ISO 898-1
DIN 267-9
Fasteners - Part 9: Technical delivery conditions; Components with Electroplated Coatings
Withdrawn DIN EN ISO 4042 ISO 4042
DIN 267-10 Fasteners - Part 10: Technical delivery conditions; Hot dip
Withdrawn DIN EN ISO 10684 ISO 10684
galvanized parts
DIN 267-11
Fasteners - Part 11: Technical delivery conditions (with additions to ISO 3506); Corrosion-resistant stainless steel fasteners
Active
DIN 267-12
Fasteners - Part 12: Technical delivery conditions; Self-tapping screws
Withdrawn DIN EN ISO 2702 ISO 2702
DIN 267-13 Fasteners - Part 13: Technical delivery conditions; Components for Bolted Connections Made Mainly from Materials Exhibiting a High Impact Strength at Low Temperature or from Materials with a High Temperature
Active
Strength
DIN 267-15
Fasteners - Part 15: Technical delivery conditions; Prevailing torque type nuts
Withdrawn
DIN EN ISO 2320,DIN EN ISO 3506-1,DIN EN ISO 3506-2,DIN EN ISO 3506-3
ISO 2320,ISO 3506-1,ISO 3506-2,ISO 3506-3
DIN 267-18
Fasteners - Part 18: Technical delivery conditions; Components made of Non-ferrous Metals
Withdrawn DIN EN 28839 ISO 8839
DIN 267-19
Fasteners - Part 19: Technical delivery conditions; Surface discontinuities on bolts and screws
WithdrawnDIN EN ISO 26157-1,DIN EN ISO 26157-3
ISO 6157-1,ISO 6157-3
DIN 267-20
Fasteners - Part 20: Technical delivery conditions; Surface discontinuities on nuts
WithdrawnDIN EN ISO 6157-2,DIN EN ISO 10484,DIN EN ISO 10485
ISO 6157-2,ISO 10484,ISO 10485
DIN 267-21 Fasteners - Part 21:
Withdrawn DIN EN ISO 6157-2,DIN EN ISO 10484,
ISO 6157-2,ISO 10484,
Technical delivery conditions; Widening test on nuts
DIN EN ISO 10485 ISO 10485
DIN 267-23
Fasteners - Part 23: Technical delivery conditions; Property classes for nuts with fine thread (ISO classes)
Withdrawn DIN EN ISO 898-6 ISO 898-6
DIN 267-24
Fasteners - Part 24: Technical delivery conditions; Property classes for nuts (Hardness classes)
Active
DIN 267-25
Fasteners - Part 25: Technical delivery conditions; Torsion testing of M1 to M10 bolts and screws
Withdrawn DIN EN 20898-7 EN 20898-7
DIN 267-26 Fasteners - Part 26: Technical delivery conditions;
Active
Conical spring washers for bolt/nut assemblies
DIN 267-27
Fasteners - Part 27: Technical specifications; Steel screws, bolts and studs with adhesive coating
Active
DIN 267-28
Fasteners - Part 28: Technical specifications; Steel screws, bolts and studs with locking coating
Active
DIN 267-29
Fasteners - Part 29: Technical specifications; Product grades for parts for bolted connections for use at temperatures ranging from -200°C to +700°C
Active
DIN 267-30 Fasteners - Part 30: Technical specifications; Metric thread
Active
rolling screws of property class 10.9
DIN 276-1
Building costs; Part 1: Building construction
Active
DIN 276-2
Building costs; Part 2: Classification of cost
Active
DIN 276-3
Building costs; Part 3: Ascertainment of cost
Active
[edit] DIN 300 to DIN 399
DIN TITLE STATUS DIN REPLACEMENT OTHER ORG
REPLACEMENT
DIN 315Wing nuts with rounded wings
Active
DIN 316Wing screws with rounded wings
Active
DIN 323-1 Preferred Numbers and Series of Preferred Numbers; Basic Values,
Active
Calculated Values, Rounded Values
DIN 323-2
Preferred Numbers and Series of Preferred Numbers; Introduction
Active
DIN 332-1
60° centre holes; types R, A, B, and C
Active
DIN 332-2
Center holes 60° with thread for shaft ends for rotating electrical machines
Active
DIN 332-4
Centre holes for rail vehicles axles
Active
DIN 332-7
Machine tools; 60° centre holes; dimensioning
Active
DIN 332-8
Centre holes 90°, form S; dimensions, determination process
Active
DIN 332-10
Center Holes; Indications on Technical Drawings
Withdrawn DIN ISO 6411 ISO 6411
DIN 338
Parallel shank twist drills, jobber series
Active
[edit] DIN 400 to DIN 499
DIN TITLE STATUS DIN REPLACEMENT OTHER ORG
REPLACEMENT
DIN 404Slotted capstan screws
Active
DIN 406-10
Engineering drawing practice; dimensioning; concepts and general principles
Active
DIN 406-11
Engineering drawing practice; dimensioning; principles of application
Active
DIN 406-12
Engineering drawing practice; dimensioning; tolerancing of linear and
Active
angular dimensions (modified version of ISO 406:1987)
DIN 417Slotted set screws with long dog point
Withdrawn DIN EN 27435 ISO 7435
DIN 427
Slotted headless screws with chamfered end
Withdrawn DIN EN ISO 2342 ISO 2342
DIN 428Hexagon nuts, Grade C
Withdrawn DIN EN ISO 4034 ISO 4034
DIN 433
Washers for use with cheese head screws
Withdrawn DIN EN ISO 7092 ISO 7092
DIN 433-1
Product grade A washers - with a hardness up to 250 HV designed for use with cheese head screws
Withdrawn DIN EN ISO 7092 ISO 7092
DIN 433-2
Product grade A washers - with a hardness up to 300 HV designed for use with
Withdrawn DIN EN ISO 7092 ISO 7092
cheese head screws
DIN 438Slotted set screws with cup point
Withdrawn DIN EN 27436 ISO 7436
DIN 439Hexagon thin nuts
WithdrawnDIN EN ISO 4035, DIN EN ISO 4036, DIN EN ISO 8675
ISO 4035, ISO 4036,ISO 8675
DIN 439-1
Unchamfered hexagon thin nuts - Product grade B
Withdrawn DIN EN ISO 4036 ISO 4036
DIN 439-2
Chamfered hexagon thin nuts - Product grades A and B
WithdrawnDIN EN ISO 4035, DIN EN ISO 8675
ISO 4035, ISO 8675
DIN 440Washers for use in timber constructions
Withdrawn DIN EN ISO 7094 ISO 7094
DIN 444 Eyebolts Active
DIN 461
Graphical Representation in Systems of Coordinates
Active
DIN 462 Machine Tools; Internal Tab Washers for Slotted Round Nuts for Hook Spanner
Active
according to DIN 1804
DIN 464Knurled thumb screws, high type
Active
DIN 466Knurled nuts, high type
Active
DIN 467Knurled nuts, low type
Active
DIN 471
Circlips (retaining rings) for shafts; Normal type and heavy type
Active
DIN 476 Paper sizes Withdrawn DIN EN ISO 216 ISO 216
DIN 476-2
Trimmed Sizes of Paper - C Series
Active
DIN 477 DIN 479Square head bolts with short dog point
Active
[edit] DIN 500 to DIN 599
DIN TITLE STATUS DIN REPLACEMENT OTHER ORG
REPLACEMENT
DIN 522 Metal washers; technical
Withdrawn DIN EN ISO 4759-3 ISO 4759-3
delivery conditions
DIN 551
Slotted set screws with flat point
Withdrawn DIN EN 24766 ISO 4766
DIN 553
Slotted set screws with cone point
Withdrawn DIN EN 27434 ISO 7434
DIN 555
M5 to M100x6 hexagon nuts - Product grade C
Withdrawn DIN EN ISO 4034 ISO 4034
DIN 558Hexagon head screws
Withdrawn DIN EN ISO 4018 ISO 4018
DIN 580
Collar eyebolts for lifting purposes
Active
[edit] DIN 600 to DIN 699
DIN TITLE STATUS DIN REPLACEMENT OTHER ORG
REPLACEMENT
DIN 601 M5 to M52 hexagon head bolts; product
Withdrawn DIN EN ISO 4016 ISO 4016
grade C
DIN 603
Mushroom head square neck bolts
Active
DIN 609
Hexagon fits bolts with long thread
Active
DIN 625-1
Rolling bearings; single row radial contact ball bearings
Active
DIN 625-3
Rolling bearings; double row radial contact ball bearings
Active
DIN 625-4
Rolling bearings; radial contact groove ball bearings with flanged outer ring
Active
DIN 653 Knurled thumb
Active
screws, low type
DIN 678-1Envelopes - Part 1: Sizes
Active
DIN 678-2
Envelopes - Part 2: Envelopes for Processing in Enveloping Machines, Size C6 to C4
Active
[edit] DIN 700 to DIN 799
DIN TITLE STATUS DIN REPLACEMENT OTHER ORG
REPLACEMENT
DIN 763
Tested, non-calibrated, long-link round steel chains
Active
DIN 764-1
Calibrated and tested round steel link chains for continuous conveyors; grade 2, pitch 3,5d
Active
DIN 764-2
Calibrated and tested round steel link chains for continuous conveyors; grade 3, pitch 3,5d
Active
DIN 766
Calibrated and tested grade 3 round steel link chains
Active
DIN 799-1Foundation Blocks
Active
[edit] DIN 800 to DIN 899
DIN TITLE STATUS DIN
REPLACEMENT OTHER ORG
REPLACEMENT
DIN 820-1Standards Work - Part 1: Principles
Active
DIN 820-2
Standardization - Part 2: Presentation of standards; examples for presentation of figures, tables and part lists
Active
DIN 820-3 Standardization - Part 3:
Active
Concepts
DIN 820-4
Standardization - Part 4: Working procedure
Active
DIN 820-11
Standardization - Part 11: Presentation of Standards concerning safety regulations which are VDE-Specifications or VDE-Guidelines
Active
DIN 820-12
Standardization - Part 12: Presentation of standards concerning safety regulations
Active
DIN 820-13
Standardization - Part 13: Adoption of European documents of CEN, CENELEC and of ETSI; Concepts and presentation
Active
DIN 820-15 Standardization - Part 15:
Active
Implementation of ISO and IEC international documents; Concepts and presentation
DIN 820-120
Standardization - Part 120: Guidelines for the inclusion of safety aspects in standards (ISO/IEC Guide 51:1999)
Active
DIN 824
Technical drawings; Folding to filing size
Active
DIN 899
Hand Operated Wrenches and Sockets; Technical Specifications
Withdrawn DIN ISO 1711-1 ISO 1711-1
[edit] DIN 900 to DIN 999
DIN TITLE STATUS DIN
REPLACEMENT OTHER ORG
REPLACEMENT
DIN 908
Hexagon socket screw plugs with parallel screw thread
Active
DIN 910Hexagon-duty hexagon head screw plugs
Active
DIN 911Hexagon Socket Screw Keys
Withdrawn DIN ISO 2936 ISO 2936
DIN 912
Hexagon socket head cap screws (modified version of ISO 4762)
WithdrawnDIN EN ISO 4762,DIN EN ISO 21269
ISO 4762,ISO 21269
DIN 913
Hexagon socket set screws with flat point (ISO 4026 modified)
Withdrawn DIN EN ISO 4026 ISO 4026
DIN 914
Hexagon socket set screws with cone point (ISO 4029 modified)
Withdrawn DIN EN ISO 4027 ISO 4027
DIN 915
Hexagon socket set screws with full dog point
Withdrawn DIN EN ISO 4028 ISO 4028
DIN 916
Hexagon socket set screws with cup point (ISO 4029 modified)
Withdrawn DIN EN ISO 4029 ISO 4029
DIN 918
Fasteners; Terminology; Spelling of terms; Abbreviations
Active
DIN 918-3
Overview of European Standards for fasteners
Active
DIN 919-1
Technical Drawings; Wood Processing; Principles
Active
DIN 921
Slotted pan head screws with large head
Active
DIN 923Slotted pan head screws with shoulder
Active
DIN 929Hexagon weld nuts
Active
DIN 930
Fine thread pitch partially threaded screws
Withdrawn DIN 931-1, DIN 931-2
DIN 931-1 M1,6 to M39 hexagon head bolts - Product grades A and
Withdrawn DIN EN ISO 4014 ISO 4014
B
DIN 931-2
M42 to M160x6 hexagon head bolts - Product grade B
Withdrawn DIN EN ISO 4014 ISO 4014
DIN 933
M1,6 to M52 hexagon head screws thread up to the head - Product grades A and B
Withdrawn DIN EN ISO 4017 ISO 4017
DIN 934
Hexagon nuts with metric coarse and fine pitch thread - Product classes A and B
WithdrawnDIN EN ISO 4032,DIN EN ISO 8673
ISO 4032,ISO 8673
DIN 935-1
Hexagon slotted nuts and castle nuts with metric coarse and fine pitch thread - Product grades A and B
Active
DIN 935-2 M42 to M160x6 hexagon head bolts; product
Active
grade B
DIN 935-3
Hexagon slotted nuts with metric coarse pitch thread - Product grade C
Active
DIN 936
M8 to M52 and M8x1 to M52x3 hexagon thin nuts; product grades A and B
Withdrawn
DIN 937Hexagon thin castle nuts
Withdrawn
DIN 938
Studs with a length of engagement equal to about 1 d
Active
DIN 939
Studs with a length of engagement equal to about 1,25 d
Active
DIN 946 Determination of coefficient of friction of bolt/nut assemblies under specified
Withdrawn DIN EN ISO 16047 ISO 16047
conditions
DIN 960
M8x1 to M100x4 hexagon head bolts with fine pitch thread - Product grades A and B
WithdrawnDIN EN ISO 8765,DIN EN ISO 8676
ISO 8765,ISO 8676
DIN 961
M8x1 to M52x3 hexagon head bolts with fine pitch thread - Product grades A and B
Withdrawn DIN EN ISO 8676 ISO 8676
DIN 962Designation system for fasteners
Active
DIN 963
Slotted countersunk head screws (with countersunk heads as specified in ISO 2009-1972)
Withdrawn DIN EN ISO 2009 ISO 2009
DIN 964
Slotted raised countersunk oval head screws
Withdrawn DIN EN ISO 2010 ISO 2010
DIN 965 Cross Withdrawn DIN EN ISO 7046-1, ISO 7046-1,
recessed countersunk flat head screws
DIN EN ISO 7046-2 ISO 7046-2
DIN 966
Cross recessed raised countersunk head screws
Withdrawn DIN EN ISO 7047 ISO 7047
DIN 970
Hexagon nuts; Style 1; Metric coarse thread, Product grades A and B; ISO 4032 modified
Withdrawn DIN EN ISO 4032 ISO 4032
DIN 971-1
Style 1 hexagon nuts with metric fine pitch thread; property classes 6 and 8
Withdrawn DIN EN ISO 8673 ISO 8673
DIN 971-2
Style 2 hexagon nuts with metric fine pitch thread; property classes 10 and 12
Withdrawn DIN EN ISO 8674 ISO 8674
DIN 972 M5 to M39 hexagon nuts; style 1;
Withdrawn DIN EN ISO 4034 ISO 4034
product grade C (modified version of ISO 4034)
DIN 975 Threaded rods Withdrawn
DIN 976-1Metric thread stud bolts
Active
DIN 976-2
Metric interference-fit thread stud bolts
Active
DIN 977Hexagon weld nuts with flange
Withdrawn DIN EN ISO 21670 ISO 21670
DIN 979
Hexagon thin slotted nuts and castle nuts with metric coarse and fine pitch thread - Product grades A and B
Active
DIN 980
All-metal prevailing torque type hexagon nuts
WithdrawnDIN EN ISO 7042,DIN EN ISO 10513
ISO 7042,ISO 10513
DIN 981
Locknuts for use with rolling bearings
Active
DIN 982
Prevailing torque type hexagon nuts with nonmetallic insert
WithdrawnDIN EN ISO 7040,DIN EN ISO 10512
ISO 7040,ISO 10512
DIN 983
Retaining rings with lugs for use on shafts (external circlips)
Active
DIN 985
Prevailing torque type hexagon thin nuts with nonmetallic insert
Withdrawn DIN EN ISO 10511 ISO 10511
DIN 988
Shim rings and supporting rings
Active
[edit] DIN 1000 to DIN 9999
[edit] DIN 1000 to DIN 1999
DIN TITLE STATUS DIN
REPLACEMENT OTHER ORG
REPLACEMENT
DIN 1301-1Units - Part 1: Names and Symbols
Active
DIN 1301-2 Units - Part 2: Submultiples
Active
and Multiples for General Use
DIN 1301-3
Units - Part 3: Conversions of Units No Longer To Be Used
Active
DIN 1302
General Mathematical Symbols and Concepts
Active
DIN 1303
Vectors, matrices, tensors; symbols and concepts
Active
DIN 1304-1
Letter symbols for physical quantities - Part 1: Symbols for general use
Active
DIN 1304-2
Letter symbols for physical quantities - Part 2: Symbols for use in meteorology and geophysics
Active
DIN 1304-3 Letter symbols for physical quantities - Part 3: Symbols for use in electric power
Active
engineering
DIN 1304-5
Letter symbols for physical quantities - Part 5: Symbols for use in fluid mechanics
Active
DIN 1304-8
Letter symbols for physical quantities - Part 9: Symbols for use in the field of static converters using semiconductor devices
Active
DIN 1304-9
Letter symbols for physical quantities - Part 9: Symbols for equivalent circuits of piezoelectric crystals
Active
DIN 1311-1
(Mechanical) vibrations, oscillations and vibration systems - Part 1: Basic concepts, survey
Active
DIN 1311-2 (Mechanical) vibrations, oscillations and
Active
vibration systems - Part 2: Linear vibration systems with single degree of freedom
DIN 1311-3
(Mechanical) vibrations, oscillations and vibration systems - Part 3: Linear time-invariant vibration systems with a finite number of degrees of freedom
Active
DIN 1311-4
Vibration; Vibrating Continua, Waves
Active
DIN 1313
Physical Quantities and Equation; Concepts, Methods of Writing
Active
DIN 1315Angle; Concepts, Units
Active
DIN 1318 Loudness Level Active
DIN 1319-1 Fundamentals of Metrology –
Active
Part 1: Basic Terminology
DIN 1319-2
Basic Concepts in Metrology – Part 2: Terminology Related To Measuring Equipment
Active
DIN 1319-3
Basic Concepts in Metrology – Part 3: Terminology Relating To the Uncertainty of Measurement and the Assessment of Measuring Instruments and Measuring Equipment
Active
DIN 1319-4
Basic Concepts in Metrology – Part 4: Treatment of Uncertainties in the Evaluation of Measurements
Active
DIN 1320Acoustics; Terminology
Active
DIN 1324-1Electromagnetic Field - Part 1. State Quantities
Active
DIN 1324-2
Electromagnetic Field - Part 2. Material Quantities
Active
DIN 1324-3
Electromagnetic Field - Part 3. Electromagnetic Waves
Active
DIN 1325-1
Vocabulary for value management, value analysis and functional analysis - Part 1: Value analysis and functional analysis
Active
DIN 1325-2
Value Management, Value Analysis, Functional Analysis Vocabulary - Part 2: Value Management
Active
DIN 1332Acoustics; Symbols
Withdrawn DIN EN ISO 80000-8 ISO 80000-8
DIN 1333Presentation of Numerical Data
Active
DIN 1338Writing and Typesetting of Formulae
Active
DIN 1355-1
Time; Calendar, Numbering of Weeks, Date of Day, (Clock) Time
Withdrawn
DIN 1421
Arrangement and Numbering in Texts; Clauses, Paragraphs, Enumerations
Active
DIN 1422-1
Publications in Sciences, Technology, Economy and Administration; Presentation of Manuscripts and Typoscripts
Active
DIN 1422-2
Publications in Sciences, Technology, Economy and Administration; Presentation of Clean Copies for Reprographic Use
Active
DIN 1422-3
Publications in Sciences, Technology, Economy and Administration; Typographical Presentation
Active
DIN 1422-4
Publications in Sciences, Technology, Economy and Administration; Presentation of Scientific and Technical Reports
Active
DIN 1440Medium type washers for pins
Withdrawn DIN EN 28738 ISO 8738
DIN 1443Clevis pins without head
Withdrawn DIN EN 22340 ISO 2340
DIN 1444Clevis pins with head
Withdrawn DIN EN 22341 ISO 2341
DIN 1451-1
Lettering - Linear-Antiqua without serifes – General
Active
DIN 1451-2
Typefaces - lineal Linear-Antiqua; lettering for transportation
Active
DIN 1451-3
Lettering - Linear-Antiqua without serifes; lettering for printing
Active
DIN 1451-4 Typefaces - lineal Linear-Antiqua;
Active
stenciled lettering for engraving and other processes
DIN 1463-1
Guidelines for the Establishment and Development of Thesauri; Monolingual Thesauri
Active
DIN 1463-2
Guidelines for the Establishment and Development of Thesauri; Multilingual Thesauri
Active
DIN 1470
Grooved Pins, Full Length Parallel-grooved with Pilot
Withdrawn DIN EN 8739 ISO 8739
DIN 1471Grooved Pins, Full Length Taper-grooved
Withdrawn DIN EN 8744 ISO 8744
DIN 1472Grooved Pins, Half Length Taper-grooved
Withdrawn DIN EN 8745 ISO 8745
DIN 1473 Grooved Pins, Full Length Parallel-
Withdrawn DIN EN ISO 8740 ISO 8740
grooved with Chamfer
DIN 1474
Grooved Pins, Half Length Reverse-grooved
Withdrawn DIN EN 8741 ISO 8741
DIN 1475Grooved Pins, Third Length Centre-grooved
Withdrawn DIN EN 8742 ISO 8742
DIN 1476Round Head Grooved Pins
Withdrawn DIN EN 8746 ISO 8746
DIN 1477Countersunk Head Grooved Pins
Withdrawn DIN EN 8747 ISO 8747
DIN 1481
Spring-Type Straight Pins (Roll Pins) - Heavy Type
Withdrawn DIN EN ISO 8752 ISO 8752
DIN 1505-1
Bibliographic references to documents - Part 1: Full References to Printed and Published Documents
Active
DIN 1505-2
Bibliographic references to documents - Part 2: Rules for Citing
Active
DIN 1505-3
Bibliographic references to documents - Part 3: Indexes of cited documents (bibliographies)
Active
DIN 1511
Pattern Equipment for Foundries; Production and Quality
Withdrawn DIN EN 12890 EN 12890
DIN 1530-1
Tools for moulding - Part 1: Ejector pins with cylindrical head
Active
DIN 1530-2
Tools for moulding - Part 2: Shouldered ejector pins
Active
DIN 1530-3
Tools for moulding - Part 3: Ejector pins with conical head
Active
DIN 1587Hexagon domed cap nuts
Active
DIN 1707
Soft Solders; Composition, Technical Delivery Condition
Withdrawn DIN EN ISO 9453 ISO 9453
DIN 1712 Part 1
Aluminium and aluminium alloys - Unalloyed aluminium ingots for remelting – Specifications
Withdrawn DIN EN 576 EN 576
DIN 1712 Part 3
Aluminium; Half-Finished Products
Withdrawn DIN EN 573-3 EN 573-3
DIN 1783
Strips, Plates and Sheets of Aluminium and Wrought
Withdrawn DIN EN 485-4 EN 485-4
DIN 1786
Seamless Drawn Copper Tubes for Piping Systems
Withdrawn DIN EN 1057 EN 1057
DIN 1798
Round Rod of Aluminium (Highest Grade Aluminium)
Withdrawn DIN EN 754-3 EN 754-3
DIN 1804
Slotted Round Nut for Hook Spanner; ISO Metric Fine Thread
Active
DIN 1810 Hook wrenches Active
DIN 1816 Round Nut with Set Pin Holes Inside; ISO
Active
Metric Fine Thread
DIN 1912-1
Graphical Representation of Welded, Soldered and Brazed Joints
Withdrawn DIN EN ISO 17659 ISO 17659
DIN 1912-2
Graphical Representation of Welded, Soldered and Brazed Joints
Withdrawn DIN EN ISO 6947 ISO 6947
DIN 1912-4
Graphical Representation of Welded, Soldered and Brazed Joints; Concepts and Terms for Soldered and Brazed Joints and Seams
Active
DIN 1912-5
Symbolic Representation on Drawings of Welded, Soldered and Brazed Joints
Withdrawn DIN EN 22553 ISO 2553
DIN 1960 Construction contract procedures (VOB) - Part A: General provisions relating to the award of
Active
construction contracts
DIN 1961
Construction contract procedures (VOB) - Part B: General conditions of contract relating to the execution of construction work
Active
[edit] DIN 2000 to DIN 2999
DIN TITLE STATUS DIN
REPLACEMENT OTHER ORG
REPLACEMENT
DIN 2112
Alphanumeric office machines - Alphanumeric keyboards, keyboard arrangement for manually operated typewriters
Withdrawn DIN 2137-6, DIN 2137-10
DIN 2127 Alphanumeric office machines; alphanumeric keyboards, keyboard arrangement for electro-mechanical operated
Withdrawn DIN 2137-6, DIN 2137-10
typewriters
DIN 2137-1
Text and office systems - Keyboards - Part 1: German keyboard for typewriters; key arrangement and allocation of characters to keys
Active
DIN 2137-2
Text and office systems - Keyboards - Part 2: German keyboard for data and text processing; Key arrangement and allocation of graphic characters to keys
Active
DIN 2137-6 Text and office systems - Keyboards - Part 6: German keyboard for data and text processing as well as for typewriters;
Active
Key arrangement and allocation of functions to keys
DIN 2137-10
Text and office systems - Keyboards - Part 10: German keyboard for data and text processing as well as for typewriters; Arrangement of key positions and key distances
Active
DIN 2137-11
Text and office systems - Keyboards - Part 11: German keyboard for data and text processing as well as for typewriters; Principles governing the allocation of characters or functions to keys and the placement of their symbols on the keys
Active
DIN 2137-12
Text and office systems - Keyboards - Part 12: German keyboard for data and text processing; Key arrangement and allocation for portable computers
Active
DIN 2342-1
Vocabulary of terminology; basic concepts
Active
DIN 2391-1
Seamless precision steel tubes - Part 1: Dimensions
Canceled DIN EN 10305-1 EN 10305-1
DIN 2391-2
Seamless precision steel tubes - Part 2: Technical delivery conditions
Canceled DIN EN 10305-1 EN 10305-1
DIN 2448 Seamless Steel Pipes and Tubes - Dimensions, Conventional Masses per
Canceled DIN EN 10220 EN 10220
Unit Length
DIN 2527
Blank flanges - Nominal pressure 6 to 100
Withdrawn DIN EN 1092-1 EN 1092-1
DIN 2860
Capillary Fittings; Bends 180° of Copper
Withdrawn
DIN 2999-1
Pipe threads for tubes and fittings; parallel internal thread and taper external thread; tread dimensions
Withdrawn DIN EN 10226-1 EN 10226-1
DIN 2999-2
Whitworth Pipe Threads for Tubes and Fittings; Cylindrical Internal Thread and Conical External Thread, Gauging System and Use of Gauges
Withdrawn DIN EN 10226-3 EN 10226-3
DIN 2999-3 Whitworth Pipe Threads for Tubes and Fittings;
Withdrawn DIN EN 10226-3 EN 10226-3
Gauge Dimensions
DIN 2999-4
Pipe threads for tubes and fittings; sizes for taper screw limit plug gauges for parallel internal thread
Withdrawn DIN EN 10226-3 EN 10226-3
DIN 2999-5
Whitworth Pipe Threads for Tubes and Fittings; Cylindrical Screw Limit Ring Gauges for Gauging Conical External Threads, Sizes
Withdrawn DIN EN 10226-3 EN 10226-3
DIN 2999-6
Whitworth Pipe Threads for Tubes and Fittings; Conical Screw Check Plugs, Sizes
Withdrawn DIN EN 10226-3 EN 10226-3
[edit] DIN 4000 to DIN 4999
DIN TITLE STATUS DIN
REPLACEMENT OTHER ORG
REPLACEMENT
DIN 4102-1
Fire behaviour of building materials and elements - Part 1: Classification of building materials - Requirements and testing
Active
DIN 4102-2
Fire Behaviour of Building Materials and Building Components - Part 2: Building Components; Definitions, Requirements and Tests
Active
DIN 4102-3
Fire Behaviour of Building Materials and Building Components - Part 3: Fire Walls and Non-load-bearing External Walls; Definitions, Requirements and Tests
Active
DIN 4102-4
Fire behaviour of building materials and elements - Part 4: Overview and design of classified building materials,
Active
elements and components
DIN 4102-5
Fire Behaviour of Building Materials and Building Components - Part 5: Fire Barriers, Barriers in Lift Wells and Glazings Resistant against Fire; Definitions, Requirements and Tests
Active
DIN 4102-6
Fire Behaviour of Building Materials and Building Components - Part 6: Ventilation Ducts; Definitions, Requirements and Tests
Active
DIN 4102-7
Fire behaviour of building materials and elements - Part 7: Roofing - Concepts, requirements and testing
Active
DIN 4102-8
Fire behaviour of building materials and components -
Active
Part 8: Small scale test furnace
DIN 4102-9
Fire behaviour of building materials and elements - Part 9: seals for cable penetrations; concepts, requirements and testing
Active
DIN 4102-11
Fire behaviour of building materials and building components - Part 10: pipe encasements, pipe bushings, service shafts and ducts, and barriers across inspection openings; terminology, requirements and testing
Active
DIN 4102-12
Fire behaviour of building materials and elements - Part 12: Fire resistance of electric cable systems required to maintain circuit integrity - Requirements and testing
Active
DIN 4102-13
Fire behaviour of building materials and elements - Part 13: Fire resistant glazing; concepts, requirements and testing
Active
DIN 4102-14
Fire behaviour of building materials and elements - Part 14: Determination of the burning behaviour of floor covering systems using a radiant heat source
Active
DIN 4102-15
Fire behaviour of building materials and elements - Part 15: "Brandschacht"
Active
DIN 4102-16
Fire behaviour of building materials and elements - Part 16: "Brandschacht" tests
Active
DIN 4102-17
Fire behaviour of building materials and elements - Part
Active
17: determination of melting point of mineral fibre insulating materials; concepts, requirements and testing
DIN 4102-18
Fire behaviour of building materials and components - Part 18: fire barriers, verification of automatic closure (continuous performance test)
Active
DIN 4102-22
Fire behaviour of building materials and building components - Part 22: Application standard for DIN 4102-4 based on the design of partial safety factors
Active
DIN 4108-1
Thermal protection and energy economy in buildings - Part 1: Quantities and units
Active
DIN 4108-2
Thermal protection and
Active
energy economy in buildings - Part 2: Minimum requirements to thermal insulation
DIN 4108-3
Thermal protection and energy economy in buildings - Part 3: Protection against moisture subject to climate conditions; Requirements and directions for design and construction
Active
DIN 4108-7
Thermal insulation and energy economy of buildings - Part 7: Airtightness of building, requirements, recommendations and examples for planning and performance
Active
DIN 4108-10
Thermal insulation and energy economy in buildings - Part 10: Application-related requirements for thermal insulation
Active
materials - Factory made products
DIN 4150-1
Structural vibration - Part 1: Prediction of vibration parameters
Active
DIN 4150-2
Structural vibration - Part 2: Human exposure to vibration in buildings
Active
DIN 4150-3
Structural vibration - Part 3: Effects of vibration on structures
Active
DIN V 4701-10
Energy efficiency of heating and ventilation systems in buildings - Part 10: Heating, domestic hot water supply, ventilation
Active
DIN V 4701-12
Energetic evaluation of heating and ventilation systems in existing buildings - Part 12: Heat
Active
generation and domestic hot water generation
DIN 4710
Statistics on German meteorological data for calculating the energy requirements for heating and air conditioning equipment
Active
[edit] DIN 5000 to DIN 5999
DIN TITLE STATUS DIN
REPLACEMENT OTHER ORG
REPLACEMENT
DIN 5008Rules for text presentation
Active
DIN 5031-1
Physics of radiation in the field of optics and illuminating engineering - Part 1: Quantities, symbols and units of radiation physics
Active
DIN 5031-2
Physics of radiation in the field of optics and illuminating engineering - Part 2:
Active
Evaluation of radiation by different detectors
DIN 5031-3
Physics of radiation in the field of optics and illuminating engineering - Part 3: Quantities, symbols and units of illuminating engineering
Active
DIN 5031-4
Physics of radiation in the field of optics and illuminating engineering - Part 4: Efficiencies
Active
DIN 5031-5
Physics of radiation in the field of optics and illuminating engineering - Part 5: Definitions for temperatures
Active
DIN 5031-6
Physics of radiation in the field of optics and illuminating engineering - Part 6: Pupil intensity as a measure of
Active
retinal illumination
DIN 5031-7
Physics of radiation in the field of optics and illuminating engineering - Part 7: Terms for wavebands
Active
DIN 5031-8
Physics of radiation in the field of optics and illuminating engineering - Part 8: Definitions and constants of radiation physics
Active
DIN 5031-9
Physics of radiation in the field of optics and illuminating engineering - Part 9: Definitions in the field of luminescence
Active
DIN 5031-10
Physics of radiation in the field of optics and illuminating engineering - Part 10: Photobiologically effective radiation, quantities, symbols and
Active
actions
DIN 5035-3
Artificial lighting - Part 3: Lighting of health care premises
Active
DIN 5035-6
Artificial lighting - Part 6: Measurement and evaluation
Active
DIN 5035-7
Artificial lighting - Part 7: Lighting of interiors with visual displays work stations
Active
DIN 5035-8
Artificial lighting - Part 8: Workplace luminaries - Requirements, recommendations and proofing
Active
DIN 5145Plane irons for wood smooth and for planes
Active
DIN 5146Curved irons for jack planes
Active
DIN 5406
Lockwashers and locking plates for use with rolling bearings
Active
DIN 5473Logic and set theory; symbols and concepts
Active
DIN 5474Signs in mathematical logic
Withdrawn DIN 5473
DIN 5475-1
Complex quantities; nomenclature
Withdrawn DIN 5483-3
DIN 5483-1
Time-dependent quantities - Part 1: Terms for the time-dependency
Active
DIN 5483-2
Time-dependent quantities - Part 2: Letter symbols
Active
DIN 5483-3
Time-dependent quantities - Part 3: Complex representation of sinusoidal time-dependent quantities
Active
DIN 5486Notation of matrices
Withdrawn DIN 1303
DIN 5487
Fourier-, Laplace- and Z-transformation; symbols and concepts
Active
DIN 5489 Directions and Withdrawn DIN EN 60375 EN 60375
signs in electrical engineering; rules for electric and magnetic circuits, equivalent circuit diagrams
DIN 5493-2
Logarithmic quantities and units - Part 2: Logarithmic ratios, levels in nepers and decibels
Active
[edit] DIN 6000 to DIN 6999
DIN TITLE STATUS DIN
REPLACEMENT OTHER ORG
REPLACEMENT
DIN 6319
Spherical washers and conical seats
Active
DIN 6325
Parallel Pins, Hardened; Tolerance Zone m6
Withdrawn DIN EN ISO 8734 ISO 8734
DIN 6340Washers for clamping devices
Active
DIN 6738 Paper and paper board - Lifespan
Active
classes
DIN 6776Technical drawings, labeling
Withdrawn DIN EN ISO 3098 ISO 3098
DIN 6797Toothed lock washers
Withdrawn
DIN 6798Serrated lock washers
Withdrawn
DIN 6799
Lock washers (retaining washers) for shafts
Active
DIN 6880
Bright Key Steel; Dimensions, Permissible Variations, Weights
Active
DIN 6885-1
Drive Type Fastenings without Taper Action – Part 1: Parallel Keys, Keyways, Deep Pattern
Active
DIN 6885-2
Drive Type Fastenings without Taper Action – Part 2: Parallel Keys, Keyways, Deep Pattern for Machine Tools, Dimensions and Application
Active
DIN 6885-3
Drive Type Fastenings without Taper Action – Part 3: Parallel Keys, Shallow Pattern, Dimensions and Application
Active
DIN 6900Screw and Washer Assemblies
Withdrawn DIN EN 10644 EN 10644
DIN 6901
Tapping screw and washer assemblies
Withdrawn DIN EN 10510 EN 10510
DIN 6902 Plain washers for
Withdrawn DIN EN 10673 EN 10673
screw and washer assemblies
DIN 6903
Plain washers for tapping screw and washer assemblies
Withdrawn DIN EN 10669 EN 10669
DIN 6912
Hexagon socket thin head cap screws with pilot recess
Active
DIN 6914
High-strength hexagon head bolts with large widths across flats for structural steel bolting
Withdrawn DIN EN 14399-4 EN 14399-4
DIN 6916
Round washers for high-strength structural steel bolting
Withdrawn
DIN 6921Hexagon flange bolts
Withdrawn DIN EN 1665 EN 1665
DIN 6922 Hexagon flange bolts
Withdrawn DIN EN 1665 EN 1665
with reduced shank
DIN 6923Hexagon nuts with flange
Withdrawn DIN EN 1661 EN 1661
DIN 6924
Prevailing torque type hexagon nuts with nonmetallic insert
WithdrawnDIN EN ISO 7040,DIN EN ISO 10512
ISO 7040,ISO 10512
DIN 6925
Prevailing torque type all-metal hexagon nuts
WithdrawnDIN EN ISO 7042,DIN EN ISO 10513
ISO 7042,ISO 10513
DIN 6926
Prevailing torque type hexagon nuts with flange and with non-metallic insert
WithdrawnDIN EN 1663, DIN EN 1666
ISO 7043 (modified), ISO 12125 (modified)
DIN 6927
Prevailing torque type all-metal nuts with flange
WithdrawnDIN EN 1664, DIN EN 1667
ISO 7044 (modified),ISO 12126 (modified)
[edit] DIN 7000 to DIN 7999
DIN TITLE STATUS DIN REPLACEMENT OTHER ORG
REPLACEMENT
DIN 7045
Pan head screws with type H or type Z cross recess - product grade A
Active
DIN 7245
Saw blades for web saws
Active
DIN 7337
Break mandrel blind rivets
Withdrawn
DIN EN ISO 14589, DIN EN ISO 15977, DIN EN ISO 15978, DIN EN ISO 15979, DIN EN ISO 15980, DIN EN ISO 15981, DIN EN ISO 15982, DIN EN ISO 15983, DIN EN ISO 15984, DIN EN ISO 16582, DIN EN ISO 16583, DIN EN ISO 16584
ISO 14589, ISO 15977, ISO 15978, ISO 15979, ISO 15980, ISO 15981, ISO 15982, ISO 15983, ISO 15984, ISO 16582, ISO 16583, ISO 16584
DIN 7343
Spiral Pins; Normal Type
Withdrawn DIN EN ISO 8750 ISO 8750
DIN 7344
Spiral Pins; Heavy Duty Type
Withdrawn DIN EN ISO 8748 ISO 8748
DIN 7346
Spring-Type Straight Pins; (Roll Pins) Light-weight Type
Withdrawn DIN EN ISO 13337 ISO 13337
DIN Plain Active
7349
Washers for Bolts with Heavy Clamping Sleeves
DIN 7500-1
Thread rolling screws for metric ISO thread - Part 1: Types, designation, requirements
Withdrawn ISO 7085
DIN 7500-2
Thread rolling screws for ISO metric thread; guideline values for hole diameters
Active
DIN 7504
Self-drilling screws with tapping screw thread - Dimensions, requirements and testing
Withdrawn DIN EN ISO 10666, DIN EN ISO 15480, DIN EN ISO 15481, DIN EN ISO 15482, DIN EN ISO 15483
ISO 10666, ISO 15480, ISO 15481, ISO 15482, ISO 15483
DIN 7513
Hexagon head and slotted head thread cutting screws - Dimensions,
Active
requirements and testing
DIN 7516
Cross recessed head thread cutting screws - Dimensions, requirements and testing
Active
DIN 7603
Ring seals and gaskets
Active
DIN 7962
Cross recesses for screws; (modified version of ISO 4757)
Withdrawn DIN EN ISO 4757 ISO 4757
DIN 7970
Threads and thread ends for tapping screws (modified version of ISO 1478)
Withdrawn DIN EN ISO 1478 ISO 1478
DIN 7971
Slotted pan head tapping screws
Withdrawn DIN ISO 1481 ISO 1481
DIN 7972
Slotted countersunk head tapping screws
Withdrawn DIN ISO 1482 ISO 1482
DIN 7973
Slotted raised countersunk head tapping screws
Withdrawn DIN ISO 1483 ISO 1483
DIN 7977
Taper Pins with Thread Ends and Constant Point Lengths
Withdrawn DIN EN 28737 ISO 8737
DIN 7978
Taper Pins with Internal Thread
Withdrawn DIN EN 28737 ISO 8736
DIN 7979
Parallel Pins with Internal Thread
WithdrawnDIN EN ISO 8733,DIN EN ISO 8735
ISO 8733,ISO 8735
DIN 7980
Spring lock washers with square ends for cheese head screws
Withdrawn
DIN 7981
Cross recessed pan head tapping screws
Withdrawn DIN ISO 7049 ISO 7049
DIN 7982
Cross recessed countersunk head tapping screws
Withdrawn DIN ISO 7050 ISO 7050
DIN 7983
Countersunk (Flat) Head Tapping Screws with Cross Recess
Withdrawn DIN ISO 7051 ISO 7051
DIN 7984
Hexagon socket thin head cap screws
Active
DIN 7985
Cross recessed raised cheese head screws
Withdrawn DIN EN ISO 7045 ISO 7045
DIN 7991
Hexagon socket countersunk head cap screws
Withdrawn DIN EN ISO 10642 ISO 10642
[edit] DIN 8000 to DIN 8999
DIN TITLE STATUS DIN
REPLACEMENT OTHER ORG
REPLACEMENT
DIN 8074Polyethylene (PE) pipes – Dimensions
Active
DIN 8075 Polyethylene (PE) pipes - PE 63, PE 80, PE 100, PE-HD - General quality
Active
requirements, testing
DIN 8513-1
Brazing and Braze Weld Filler Metals; Copper Base Brazing Alloys; Composition, Use, Technical Conditions of Delivery
Withdrawn DIN EN 1044 EN 1044
DIN 8513-2
Brazing and Braze Weld Filler Metals; Silver-bearing Brazing Alloys with less than 20% by wt. Silver; Composition, Use, Technical Conditions of Delivery
Withdrawn DIN EN 1044 EN 1044
DIN 8513-3
Brazing filler metals; silver brazing filler metals containing not less than 20 % of silver; composition, application, technical delivery conditions
Withdrawn DIN EN 1044 EN 1044
DIN 8513-4
Brazing and Braze Weld Filler Metals; Aluminium-Base Brazing Alloys; Composition, Use, Technical Conditions of Delivery
Withdrawn DIN EN 1044 EN 1044
DIN 8513-5
Brazing filler metals; Nickel base filler metals for high temperature brazing; Application, composition, technical delivery conditions
Withdrawn DIN EN 1044 EN 1044
DIN 8580
Manufacturing processes - Terms and definitions, division
Active
DIN 8806-1
Narrow band saw blades for woodworking; dimensions
Active
[edit] DIN 9000 to DIN 9999
DIN TITLE STATUS DIN REPLACEMENT OTHER ORG
REPLACEMENT
DIN 9021
Plain washers with large outside diameter
WithdrawnDIN EN ISO 7093-1, DIN EN ISO 7093-2
ISO 7093-1, ISO 7093-2
[edit] DIN 10000 to DIN 19999
[edit] DIN 10000 to DIN 10999
DIN TITLE STATUS DIN REPLACEMENT OTHER ORG
REPLACEMENT
DIN 10504
Food hygiene - Lamps for the lighting of meat and meat products
Withdrawn
[edit] DIN 11000 to DIN 11999
DIN TITLE STATUS DIN
REPLACEMENT OTHER ORG
REPLACEMENT
DIN 11850
Tubes for the food, chemical and pharmaceutical industry - Stainless steel tubes - Dimensions, materials
Active
[edit] DIN 12000 to DIN 12999
DIN TITLE STATUS DIN
REPLACEMENT OTHER ORG
REPLACEMENT
DIN 12950-1
Laboratory furniture; safety cabinets for microbiological and biotechnological work; safety requirements, tests
Withdrawn
DIN 12950-2
Laboratory furniture; safety cabinets for microbiological and biotechnological work; containment of class 1 and class 2 cabinets, microbiological test
Withdrawn
DIN 12950-10
Laboratory furniture; safety cabinets for microbiological and biotechnological and biotechnological work; requirements and testing
Withdrawn
[edit] DIN 13000 to DIN 13999
DIN TITLE STATUS DIN REPLACEMENT OTHER ORG
REPLACEMENT
DIN 13080
Division of hospitals into functional areas and functional sections
Active
DIN 13260-2
Supply systems for medical gases - Part 2: Dimensions and allocation of probes and gas-specific connection points for terminal units for compressed medical gases and vacuum
Active
[edit] DIN 14000 to DIN 14999
DIN TITLE STATUS DIN REPLACEMENT OTHER ORG
REPLACEMENT
DIN 14090Areas for the fire brigade on premises
Active
DIN 14096-1
Fire precaution regulation - Part 1: General and part A (placard); rules for drafting and placarding
Active
DIN 14096-2
Fire precaution regulation - Part 2: Part B (for persons without special tasks of fire prevention and fire fighting); rules for drafting
Active
DIN 14096-3
Fire precaution regulation - Part 3: Part C (for persons with special tasks of fire prevention and fire fighting); rules for drafting
Active
DIN 14210Water pool for firefighting
Active
DIN 14406-4
Portable fire extinguishers - Part 4: Maintenance
Active
DIN 14503
Trailers for firefighting purposes, two-wheeled; general requirements
Withdrawn DIN 14521
DIN 14505
Firefighting and rescue service vehicles - Vehicles for roller containers - General requirements
Active
DIN 14507
Rescue service vehicles - Vehicles for roller containers - General requirements
Active
DIN 14520Trailers for portable fire pumps
Withdrawn
DIN 14521
Firefighting - Trailer with removable foam-water monitor
Active
DIN 14530-5
Fire fighting vehicles - Part 5: Group pumping appliance LF 10/6, Group pumping appliance for rescue operations HLF 10/6
Active
DIN 14530-11
Fire fighting vehicles - Part 11: Group pumping appliance LF 20/16, Group pumping appliance for rescue operations HLF 20/16
Active
DIN 14530-16
Fire fighting vehicles - Part 16: Pumping appliance TSF
Active
DIN 14530-17
Fire fighting vehicles - Part 17: Pumping appliance TSF-W
Active
DIN 14530-21
Fire fighting vehicles - Part 21:
Active
Pump water tanker TLF 20/40, Pump water tanker TLF 20/40-SL
DIN 14530-22
Fire fighting vehicles - Part 22: TLF 16/24-TR
Active
DIN 14530-24
Fire fighting vehicles - Part 24: Small pumping appliance KLF
Active
DIN 14530-25
Fire fighting vehicles - Part 25: Pumping appliance STLF 10/6
Active
DIN 14555-1
Vehicles carrying tools and gears - Part 1: General requirements
Active
DIN 14555-3
Vehicles carrying tools and gears - Part 3: Emergency
Active
tender RW
DIN 14555-12
Vehicles carrying tools and gears - Part 12: Damage control tender GW-G
Active
DIN 14555-21
Vehicles carrying tools and gears - Part 21: GW-L1 for logistic tasks
Active
DIN 14555-22
Vehicles carrying tools and gears - Part 22: GW-L2 for logistic tasks
Active
DIN 14565Fire hose tender; Type SW 2000-TR
Withdrawn
DIN 14701-1
Turntable ladders and similar fire fighting vehicles; Purpose, concepts, safety equipment, requirements
Withdrawn DIN EN 1777 EN 1777
DIN 14701-2
Turntable ladders and similar fire fighting vehicles; Turn table ladders, engine driven
WithdrawnDIN EN 14043, DIN EN 14044
EN 14043, EN 14044
DIN 14701-3
Turntable ladders and similar fire fighting vehicles; Rescue baskets
Withdrawn DIN EN 1777 EN 1777
DIN 14702
Turntable ladder DL 16-4, hand operating
Active
DIN 14703Trailer Ladder AL 16-4
Active
DIN 14710-1
Hook ladder, manufactured using wood; with hinged hook
Withdrawn DIN EN 1147 EN 1147
DIN 14710-3
Hook light metal ladder
Withdrawn
DIN 14711-1
Scaling ladder; made from wood
Withdrawn DIN EN 1147 EN 1147
DIN 14711-2
Scaling ladder; made from light metal
Withdrawn DIN EN 1147 EN 1147
DIN 14711-3
Scaling ladder; socket rungs and socket parts
Withdrawn DIN EN 1147 EN 1147
DIN 14713Folding ladder
Withdrawn DIN EN 1147 EN 1147
DIN 14715-1
Three piece extension ladder made from wood
Withdrawn DIN EN 1147 EN 1147
DIN 14715-2
Three piece extension ladder; made of light metal
Withdrawn DIN EN 1147 EN 1147
[edit] DIN 15000 to DIN 15999
DIN TITLE STATUS DIN REPLACEMENT OTHER ORG
REPLACEMENT
DIN 15018-2
Cranes; steel structures; principles of design and construction
Active
DIN 15721
Film 70 mm; projection reel
Active
[edit] DIN 16000 to DIN 16999
DIN TITLE STATUS DIN REPLACEMENT OTHER ORG
REPLACEMENT
DIN 16518Classification of types
Active
DIN 16892
Cross-linked high-density polyethylene (PE-X) pipes - General quality requirements and testing
Active
DIN 16893
Cross-linked high-density polyethylene (PE-X) pipes – Dimensions
Active
[edit] DIN 17000 to DIN 17999
DIN TITLE STATUS DIN REPLACEMENT OTHER ORG
REPLACEMENT
DIN 17410 Materials for permanent magnets:
Active
Technical conditions
DIN 17471Resistance alloys
Active
[edit] DIN 18000 to DIN 18999
DIN TITLE STATUS DIN REPLACEMENT OTHER ORG
REPLACEMENT
DIN 18012
House service connections facilities - Principles for planning
Active
DIN 18013
Recesses for meter boards (electric meters)
Active
DIN 18014
Foundation earth electrode - General planning criteria
Active
DIN 18015-1
Electrical installations in residential buildings - Part 1: Planning principles
Active
DIN 18015-2
Electrical installations in residential buildings - Part 2: Nature and extent of minimum equipment
Active
DIN 18015-3
Electrical installations in residential buildings - Part 3: Wiring and disposition of electrical equipment
Active
DIN 18022
Domestic kitchens, bathrooms and WCs; design principles
Withdrawn
DIN 18024-1
Barrier-free built environment - Part 1: Streets, squares, paths, public transport, recreation areas and playgrounds - Design principles
Active
DIN 18024-2
Construction of accessible buildings - Part 2: Publicly accessible buildings and workplaces, design principles
Active
DIN 18065
Stairs in buildings - Terminology, measuring rules, main dimensions
Active
DIN 18379
Construction contract procedures (VOB) - Part C: General technical specifications in construction contracts (ATV) - Installation of air conditioning systems
Active
DIN 18382 Contract procedures for building works - Part C: General technical specifications for building works; Low-
Active
voltage installation and medium-voltage installation with nominal voltages up to including 36 kV
DIN 18384
Construction contract procedures (VOB) - Part C: General technical specifications in construction contracts (ATV); Installation of lightning protection systems
Active
DIN 18800-1
Steel structures - Part 1: Design and construction
Active
DIN 18800-2
Steel structures - Part 2: Analysis of safety against buckling of linear members and frames
Active
DIN 18800-3
Steel structures - Part 3: Analysis of safety against buckling of plates
Active
DIN 18800-4
Steel structures - Part 4: Analysis of safety against buckling of shells
Active
DIN 18800-5
Steel structures - Part 5: Composite structures of steel and concrete - Design and construction
Active
DIN 18800-7
Steel structures - Part 7: Execution and constructor's qualification
Active
[edit] DIN 19000 to DIN 19999
DIN TITLE STATUS DIN
REPLACEMENT OTHER ORG
REPLACEMENT
DIN V 19222
Control technology – Terminology
Active
DIN 19225
Measurement and control; terminology and classification of controllers
Active
DIN 19226-1
Control technology - Part 1: General terms and definitions
Active
DIN 19226-2
Control technology - Part 2: Terms and definitions; dynamic systems behaviour
Active
DIN 19226-3
Control technology - Part 3: Terms and definitions of switching systems behaviour
Active
DIN 19226-4
Control technology - Part 4: Terms and definitions of
Active
control systems
DIN 19226-5
Control technology - Part 5: Functional terms
Active
DIN 19226-6
Control technology - Part 6: Terms and definitions of functional and constructional units
Active
DIN 19227-1
Control technology; graphical symbols and identifying letters for process control engineering; symbolic representation for functions
Active
DIN 19227-2
Control technology; graphical symbols and identifying letters for process control engineering; representation
Active
of details
DIN 19237
Measurement and control; control engineering vocabulary
Withdrawn
DIN 19226-3, DIN 19226-4,DIN 19226-5, DIN 19226-6
DIN 19227-1
Control technology; graphical symbols and identifying letters for process control engineering; symbolic representation for functions
Active
DIN 19227-2
Control technology; graphical symbols and identifying letters for process control engineering; representation of details
Active
DIN 19533 Pipe-lines of high-density PE (high-density polyethylene) and low-density PE (low density polyethylene)
Withdrawn DIN EN 12201-1,DIN EN 12201-2,DIN EN 12201-3,DIN EN 12201-5
EN 12201-1,EN 12201-2,EN 12201-3,EN 12201-5
for drinking water supply; pipes, pipe connections and fittings for pipe-lines
DIN 19704-1
Hydraulic steel structures - Part 1: Criteria for design and calculation
Active
DIN 19704-2
Hydraulic steel structures - Part 2: Design and manufacturing
Active
DIN 19704-3
Hydraulic steel structures - Part 3: Electrical equipment
Active
[edit] DIN 20000 to DIN 29999
[edit] DIN 24000 to DIN 24999
DIN TITLE STATUS DIN REPLACEMENT OTHER ORG
REPLACEMENT
DIN 24190 Ventilation and air
Withdrawn
conditioning - folded and welded rectangular sheet metal ducts
DIN 24340-2
Hydraulic valves; mounting surfaces and connecting plates for directional control valves
Active
[edit] DIN 28000 to DIN 28999
DIN TITLE STATUS DIN REPLACEMENT OTHER ORG
REPLACEMENT
DIN 28610-1
Ductile iron pressure pipes with socket with cement-mortar lining for gas and water pipelines; dimensions and masses
Withdrawn DIN EN 545, DIN EN 969 EN 545, EN 969
DIN 28610-2 Ductile iron pressure pipes with
Withdrawn DIN EN 969 EN 969
socket for gas and water pipelines rated for pressures over 4 bar up to and including 16 bar; dimensions and masses
[edit] DIN 30000 to DIN 39999
DIN TITLE STATUS DIN REPLACEMENT OTHER ORG
REPLACEMENT
DIN 30722-1
Roller contact tipper vehicles, roller containers - Part 1: Roller contact tipper vehicles up to 26 t, roller containers type 1570 made from steel
Active
DIN 30722-2 Roller contact tipper vehicles, roller
Active
containers - Part 2: Roller contact tipper vehicles up to 32 t, roller containers type 1570 made from steel
DIN 30722-3
Roller contact tipper vehicles, roller containers - Part 3: Roller contact tipper vehicles up to 12 t, roller containers type 900 made from steel
Active
DIN 30722-4
Roller containers for the transport on road and rail
Active
[edit] DIN 31000 to DIN 31999
DIN TITLE STATUS DIN REPLACEMENT OTHER ORG
REPLACEMENT
DIN 31635
Conversion of the Arabic alphabet
Active
[edit] DIN 40000 to DIN 49999
DIN TITLE STATUS DIN
REPLACEMENT OTHER ORG
REPLACEMENT
DIN 40015
Frequency and wave bands
Active
DIN 40020
Guidelines for the user interface in multimedia equipment for general purpose use (IEC/TR 61997:2001)
Active
DIN 40050-9
Road vehicles; degrees of protection (IP-code); protection against foreign objects; water and contact; electrical equipment
Active
DIN 40101-1
Graphical symbols for use on equipment
Withdrawn
DIN 40101-2
Graphical symbols for use on equipment;
Active
graphical symbols from ISO 7000 for electrical engineering
DIN 40108
Electric power technology - Current systems - Concepts, quantities, letter symbols
Active
DIN 40110-1
Quantities used in alternating current theory - Part 2: Two-line circuits
Active
DIN 40110-2
Quantities used in alternating current theory - Part 2: Multi-line circuits
Active
DIN 40146-1
Telecommunications - Part 1: Basic concepts
Active
DIN 40148-1
Transmission systems and two-ports; concepts and quantities
Active
DIN 40148-2
Transmission systems and two-ports; symmetry characteristics of linear two-ports
Active
DIN 40148-3
Transmission systems and two-ports; measures for
Active
attenuation
DIN 40200
Nominal value, limiting value, rated value, rating - concepts
Active
DIN 41215
Electrical communication engineering; electromagnetic relays, definitions
Withdrawn
DIN 41301
Electro Sheets; Magnetic Materials for Transformers
Withdrawn
DIN 41309-1
Small transformers and chokes; strip-wound cut cores; types SM, SE, SU, SG and S3U; dimensions materials
Withdrawn
DIN 41309-2
Small transformers and chokes; strip-wound cut cores; technical conditions of delivery for one phase applications; types SM, SE, SU and SG
Withdrawn
DIN 41309-3
Small transformers and chokes; strip-wound cut cores; technical conditions of delivery for three phase applications;
Withdrawn
type S3U
DIN 41426
Nominal values of resistors and capacitors
Withdrawn DIN IEC 60063 IEC 60063
DIN 41429
Colour code for fixed resistors
Withdrawn DIN EN 60062 EN 60062
DIN 41524
Circular connectors for radio and associated sound equipment three and five-pole connectors
Withdrawn
DIN 41612-1
Two-part connectors for printed board, grid 2,54 mm; common mounting features; survey of types
Withdrawn DIN 41612-1 S1
DIN 41612-1 S1
Two piece connectors for printed circuits, grid 2,54 mm (0,1 in); general allusions
Withdrawn DIN EN 60603-2 EN 60603-2
DIN 41612-2
Two-part connectors for printed boards; grid 2,54mm; dimensions of types B, C and D
Withdrawn DIN EN 60603-2 EN 60603-2
DIN 41612-3
Two part connectors for printed boards; grid 2,54mm; dimensions of types F and G
Withdrawn DIN EN 60603-2 EN 60603-2
DIN 41612-4
Two-part connectors for printed boards; grid 2,54mm, dimensions of type H
Withdrawn DIN EN 60603-2 EN 60603-2
DIN 41612-5
Two-part connectors for printed boards; grid 2,54mm; ratings, requirements, tests
Withdrawn DIN EN 60603-2 EN 60603-2
DIN 41612-6
Two-part connection for printed boards; grid 2.54mm; dimensions of types Q, R and S
Withdrawn DIN EN 60603-2 EN 60603-2
DIN 41612-7
Two-part connectors for printed boards; grid 2,54 mm; dimensions of types U and V
Withdrawn DIN EN 60603-2 EN 60603-2
DIN 41612-8
Two-part connectors for printed boards; grid 2.54 mm; dimensions of type M
Withdrawn DIN EN 60603-2 EN 60603-2
DIN 41612-8 S1
Two-part connectors for printed boards; grid 2.54 mm; dimensions of type M; survey of special contracts for use with type M
Withdrawn DIN EN 60603-2 EN 60603-2
DIN 41612-9
Two-part connectors for printed boards;
Withdrawn DIN EN 60603-2 EN 60603-2
grid 2,54 mm; dimensions of type E
DIN 41612-10
Two-part connectors for printed boards; grid 2,54mm; gauges
Withdrawn DIN EN 60603-2 EN 60603-2
DIN 41612-102
Two-part connectors for printed boards; dimensions for type X
Withdrawn DIN 41612-9
DIN 41612-103
Two-part connectors for printed boards; dimensions of type M
Withdrawn DIN 41612-8
DIN 41652-1
Rack and panel connectors, trapezoidal, round contacts 1 mm; common mounting features and dimensions; survey of types
Active
DIN 41652-2
Rack and panel connectors; trapezoidal, round contacts 1 mm; ratings, requirements, tests
Active
DIN 41750-1
Rack and panel connectors, trapezoidal, round contacts ø1 mm; common mounting
Active
features and dimensions; survey of types
DIN 41750-2
Rack and panel connectors, trapezoidal, round contacts ø1 mm; ratings, requirements, tests
Active
DIN 41750-3
Rack and panel connectors, trapezoidal, round contacts ø1 mm; dimensions of type A; solder termination for free wiring
Active
DIN 41750-5
Rack and panel connectors, trapezoidal, round contacts ø1 mm; dimensions of type C; crimp termination for free wiring
Active
DIN 41782
Guidelines for the presentation of published data
Withdrawn DIN IEC 60747-2 IEC 60747-2
DIN 41786
Thyristors, definitions
Withdrawn
DIN 41855
Semiconductor devices and integrated circuits; kinds of devices and general terms
Withdrawn
DIN 41855-2
Semiconductor devices and integrated circuits; optoelectronic semiconductor devices; terms and definitions
Withdrawn
DIN 41868
Cases 10 A 3 and 10 B 3 for semiconductor devices; main dimensions
Withdrawn
DIN 41869-1
Case 23 A 3 for semiconductor devices; main dimensions
Withdrawn
DIN 41869-2
Cases 34 A 2 and 34 A 3 for semiconductor devices; main dimensions
Withdrawn
DIN 41869-3
Case 11 A 3 and 11 B 3 for semiconductor devices; main dimensions
Withdrawn
DIN 41869-4
Case 12 A 3 for semiconductor devices; main dimensions
Withdrawn
DIN 41869-5
Case 13 A 3 for semiconductor devices; main dimensions
Withdrawn
DIN 41869-6
Case 14 A 3 for semiconductor devices; main dimensions
Withdrawn
DIN 41869-7
Case type 15 for semiconductor devices; main dimensions
Withdrawn
DIN 41873
Cases type 5 for semiconductor devices and integrated circuits
Withdrawn
DIN 41876
Cases 18 A, B and C with 2 up to 4 terminals for semiconductor devices; main dimensions
Withdrawn
DIN 42400
Terminal markings for electrical equipment; general rules, alphanumeric system
Withdrawn DIN EN 60445 EN 60445
DIN 42402
Terminal markings for power transformers and reactors
Active
DIN 42403
Terminal markings for power converters
Withdrawn DIN IEC 61148 IEC 61148
DIN 42673-1
Totally enclosed fan-cooled three-phase induction
Withdrawn
motors squirrel-cage, type IM B 3, with rolling bearing; mounting dimensions and relationship frame sizes-output ratings
DIN 42673-2
Totally enclosed fan-cooled three-phase induction motors with squirrel-cage, type IM B 3, with rolling bearings; relationship frame sizes - output ratings for type of protection increased safety "e"
Active
DIN 42673-3
Totally enclosed fan-cooled three-phase induction motors with squirrel-cage, type IM B 3, with rolling bearings; relationship frame sizes - output ratings for type of protection flameproof enclosure "d"
Active
DIN 42673-4
Totally-enclosed fan-cooled alternating-current polyphase motors with squirrel-cage, design B3, with ball bearings, maximum envelope
Active
dimensions
DIN 42961
Rating plates for rotating electrical machinery; design
Active
DIN 42973
Rated output values for rotating electrical machinery for continuous duty
Active
DIN 43700
Measurement and control - Measurement and control instruments for panel mounting - Nominal front- and cut-out-dimensions
Withdrawn DIN IEC 61554 IEC 61554
DIN 43780
Electrical measuring instruments; direct acting indicating electrical measuring instruments and their accessories
Withdrawn DIN EN 60051-1 EN 60051-1
DIN 43802-2
Line scales and pointers for indicating electrical measuring instruments; general requirements
Active
DIN 43802-3
Line scales and pointers for indicating electrical measuring instruments; designs and dimensions
Active
DIN 43802-4
Line scales and pointers for indicating electrical measuring instruments; scale graduation and numbering
Active
DIN 43807
Measuring and control; electrical measuring instruments; terminal markings for switchboard meters, panel meters and measuring transducers for the measurement of power and power factor
Active
DIN 43856
Electricity meters, tariff time switches and ripple control receivers; connection diagrams, terminal marking, circuit diagrams
Active
DIN 43856-2
Electricity meters - Part 2: Marking of auxiliary terminals for tariff devices according to IEC-Report 61354:1995
Active
DIN 43870-1
Meter mounting boards; dimensions based on a grid system
Active
DIN 43870-2
Meter mounting boards; functional area
Active
DIN 43870-3
Meter panels; wirings
Active
DIN 44070-1
Meter mounting boards; dimensions based on a grid system
Active
DIN 44070-2
Meter mounting boards; functional area
Active
DIN 44070-3
Meter panels; wirings
Active
DIN 44070-4
Meter panels; cover for wiring
Active
DIN 44080
Thermistors; PTC, technical terms and tests
Withdrawn
DIN 44300
Information processing; vocabulary
Withdrawn
DIN 44300-1
Information processing - Concepts - General terms
Withdrawn
DIN 44300-2
Information processing - Concepts -
Withdrawn
Representation of data
DIN 44300-3
Information processing - Concepts - Data structures
Withdrawn
DIN 44300-4
Information processing - Concepts – Programming
Withdrawn
DIN 44300-5
Information processing - Concepts - Components of digital computer systems
Withdrawn
DIN 44300-6
Information processing - Concepts – Storage
Withdrawn
DIN 44300-7
Information processing - Concepts – Times
Withdrawn
DIN 44300-8
Information processing - Concepts - Processing functions
Withdrawn
DIN 44300-9
Information processing - Concepts - Process relations and modes of operation
Withdrawn
DIN 45322
Circular connectors for radio and associated sound equipment; six-pole connectors
Withdrawn DIN EN 60130-9 EN 60130-9
DIN 45323
Connectors for coupling an external low-voltage power to portable entertainment equipment (describes at least two DC coaxial power plugs)
Active
DIN 45500-1
High fidelity audio equipment and systems; minimum performance requirements; Part 1: general
Withdrawn DIN EN 61305-1 EN 61305-1
DIN 45500-2
High fidelity audio equipment and systems; requirements for tuner equipments
Withdrawn DIN EN 61305-2 EN 61305-2
DIN 45500-3
High fidelity audio equipment and systems; requirements for disk record reproducing equipments
Withdrawn
DIN 45500-4
High fidelity audio equipment and systems; minimum performance
Withdrawn
requirements for magnetic recording and reproducing equipment
DIN 45500-5
High fidelity audio equipment and systems; minimum performance requirements for microphones
Withdrawn
DIN 45500-6
High fidelity audio equipment and systems; minimum performance requirements for amplifiers
Withdrawn DIN EN 61305-3 EN 61305-3
DIN 45500-7
High fidelity audio equipment and systems; requirements for loudspeakers
Withdrawn DIN EN 61305-5 EN 61305-5
DIN 45500-8
High fidelity audio equipment and systems; for sets and systems
Withdrawn
DIN 45500-10
High fidelity audio equipment and systems; minimum performance requirements for headphones
Withdrawn
DIN 45507
Measuring apparatus for frequency variations in sound
Withdrawn DIN IEC 60386 IEC 60386
recording equipment
DIN 45539
Disk record reproducing equipment; directives for measurements, markings and audio frequency connections, dimensions of interchangeable pickups, requirements of play back amplifiers
Withdrawn DIN IEC 60098 IEC 60098
DIN 45596
Microphones; phantom powering
Withdrawn
DIN 46400-1
Steel flats with special magnetic properties cold rolled, non - oriented, finally annealed magnetic sheet and strip hysteresis loss at frequencies above 100 Hz
Withdrawn DIN EN 10106 EN 10106
DIN 46400-3
Grain-oriented magnetic steel and strip technical conditions
Withdrawn DIN EN 10107 EN 10107
DIN 47100
Cords for telecommunication; code of insulated conductors, colour of sheath
Withdrawn
DIN 47301-1
Terms of HF-lines Active
DIN 47301-2
Terms of HF-lines Active
DIN 47301-3
Definition of radio frequency transmission lines - mean characteristic impedance - mean standing wave ratio
Active
DIN 48803
Lightning protection system; Arrangement of components and dimensions for mounting
Withdrawn
DIN 48830
Lightning protection system; Description
Withdrawn
[edit] DIN 50000 to DIN 59999
DIN TITLE STATUS DIN
REPLACEMENT OTHER ORG
REPLACEMENT
DIN 51097 Testing of floor coverings; determination of the anti-slip properties: wet-loaded barefoot areas; walking method; ramp
Withdrawn DIN 51130
test
DIN 51130
Testing of floor coverings; determination of the anti-slip properties: workrooms and fields of activities with slip danger, walking method - ramp test
Withdrawn DIN 51097
DIN 51501
Lubricants; Lubricating Oils L-AN; Minimum Requirements
Withdrawn
DIN 52368
Testing of particleboards; determination of formaldehyde emission by gas analysis
Withdrawn DIN EN 717-2 EN 717-2
DIN 53150
Paints and varnishes - Determination of the drying stage of coatings (modified Bandow-Wolff method)
Active
DIN 53452Testing of Plastics; Flexural Test
Withdrawn DIN EN ISO 178 ISO 178
DIN 53575
Flexible Cellular Polymeric Materials - Determination of Tear Strength
Withdrawn DIN EN ISO 8067 ISO 8067
DIN 55003-3
Machine tools; symbols; numerically controlled machine tools
Withdrawn
DIN 58810
Surgical implants; threads for bone screws and nuts
Withdrawn
DIN 58888
Thread connection for microscope objectives
Withdrawn DIN ISO 8038-1 ISO 8038-1
[edit] DIN 60000 to DIN 69999
DIN TITLE STATUS DIN
REPLACEMENT OTHER ORG
REPLACEMENT
DIN 66000 Information processing; switching algebra,
Active
mathematical signs and symbols
DIN 66001
Information processing; graphical symbols and their application
Active
DIN 66002
Information processing; handwriting of the digit 0 and of the upper case letter O
Active
DIN 66003Information technology - 7-bit code
Active
DIN 66004-1
Information processing - Coding on data media - Part 1: Representation of 7-bit code character sets on punched tape 25
Active
DIN 66004-2
Information processing - Coding on data media - Part 2: Representation of 7-bit coded and 8-bit coded character sets on punched cards
Active
DIN 66004-3
Information processing - Coding on data media - Part 3: Representation of 7-bit coded and 8-bit coded character sets on magnetic tape 12
Active
DIN 66004-4
Information processing - Coding on data media - Part 4: Representation of 7-bit coded and 8-bit coded character sets on magnetic tape cassette 3,8
Active
DIN 66004-5
Information processing - Coding on data media - Part 5: Representation of 7-bit coded and 8-bit coded set on media-flexible disk cartridge
Active
DIN 66005
Information processing; representation of packed numerics and binary data recorded on 9 tracks on magnetic tape 12
Active
DIN 66006
Presentation of ALGOL/ALCOR programs on paper tape and punch cards
Withdrawn
DIN 66007
Font CMC 7 for magnetic ink character recognition; characters and nominal dimensions
Withdrawn DIN ISO 1004 ISO 1004
DIN 66008-1
Font A for optical character recognition; characters and nominal dimensions
Active
DIN 66008-6
Font A for optical character recognition; characters and nominal dimensions; extension of the character set
Active
DIN 66008-7
Font A for optical character recognition; representation of characters by dots in a 9 × 9 matrix
Active
DIN 66009 Font B for optical character recognition;
Withdrawn
character
DIN 66020-1
Functional requirements for the interface between data terminal equipment and data circuit-terminating equipment - Part 1: General application
Active
DIN 66020-2
List of definitions for interchange circuits between data terminal equipment (DTE) and data circuit-terminating equipment (DCE) in public data networks
Active
DIN 66020-4
Data transmission; interface between data circuit-terminating equipment (DCE) and data terminal equipment (DTE)
Active
DIN 66020-9
Interface between data terminal
Active
equipment (DTE) and data circuit-terminating equipment (DCE) for synchronous transmission on group band circuits at 48000 bits per second
DIN 66021-1
Data transmission; interface between data circuit-terminating equipment (DCE) and data terminal equipment (DTE)
Active
DIN 66021-2
Interface between data terminal equipment (DTE) and data circuit-terminating equipment (DCE) for synchronous transmission on group band circuits at 48000 bits per second
Active
DIN 66025-1
Numerical control of machines, format; general
Active
requirements
DIN 66025-2
Industrial automation; numerical control of machines; format, preparatory and miscellaneous functions
Active
DIN 66027
Information processing; programming language FORTRAN
Withdrawn
DIN 66215-1
Programming of numerically controlled machines; CLDATA, general structure and record types
Active
DIN 66215-2
Programming of numerically controlled machines; CLDATA; minor elements of type 2000 records (post-processor commands)
Active
DIN 66234
Information processing; programming language PL/I
Active
DIN 66255
Information processing; programming language PL/I
Active
DIN 66256
Information processing; programming language PASCAL
Withdrawn
DIN 66257
Numerical control of machines; concepts
Withdrawn DIN ISO 2806 ISO 2806
DIN 66258-1
Interfaces and basic data link control procedures for data communication; C S-interface, V S-interface
Withdrawn
DIN 66258-2
Interface and basic data link control procedures for data communication; balanced interface for start-stop transmission using basic data link control procedures on point-to-point connection
Withdrawn
DIN 66261
Information processing; Nassi-Shneiderman flowchart symbols
Active
DIN 66264-1
Industrial automation systems and integration - Multiprocessor Control System for Industrial Machines (MPST) - Part 1: Parallel bus
Active
DIN 66264-2
Multiprocessor control system for industrial machines (MPST); industrial automatics; rules for information interchange
Active
DIN 66303Information technology - 8 bit code
Active
DIN V 66304
Industrial automation; Computer Aided Design; format for the exchange of standard parts data
Active
DIN 66325-2
Local and Metropolitan Area Networks; LLC; identical with ISO 8802-2:1989
Withdrawn ISO 8802-2
DIN 66325-4
Local and Metropolitan Area Networks; token-passing bus access method; identical with ISO/IEC 8802-4:1990
Withdrawn ISO/IEC 8802-4
DIN 69901
Project controlling; project management; concepts
Active
[edit] DIN 70000 to DIN 79999
DIN TITLE STATUS DIN
REPLACEMENT OTHER ORG
REPLACEMENT
DIN 71412Lubricating nipples; cone type
Active
DIN 72311-1
Lead storage batteries; starter batteries for motorcycles, nominal capacities, main
Active
dimensions
DIN 72311-4
Lead storage batteries; starter batteries, terminals, vent plugs and filler openings
Active
DIN 72311-8
Lead storage batteries; starter batteries for motor cycles and passenger cars
Active
DIN 72311-13
Lead storage batteries; starter batteries for starting, lighting and ignition, 12 V, 27, 36, 45 and 54 Ah, for lateral basic fastening 10,5
Active
DIN 72311-16
Lead storage batteries; starter batteries for starting, lighting and ignition, 12 V, 27, 36, 45, 54 and 63 Ah, for lateral basic fastening 19
Active
DIN 72311-17
Lead storage batteries;
Active
starter batteries, protective covering for terminal
DIN 72311-18
Lead storage batteries; starter batteries with basic fastening 10,5 for passenger cars and commercial vehicles; nominal capacities, main dimensions
Active
DIN 72311-20
Lead storage batteries; starter batteries for commercial vehicles; nominal capacities and main dimensions
Active
DIN 72311-21
Lead storage batteries; starter batteries with 10,5 basic fastening lugs for commercial vehicles; nominal capacities and main dimensions
Active
DIN 72552-1
Terminal markings for motor vehicles; scope, principles, requirements
Active
DIN 72552-2
Terminal markings for motor vehicles; codes
Active
DIN 72552-3
Terminal markings for motor vehicles; examples for application on circuit diagrams
Active
DIN 72552-4
Terminal markings for motor vehicles; summary
Active
DIN 75490
Radio communication devices in motor vehicles; installation space, general requirements
Active
Recommended