View
214
Download
0
Category
Preview:
Citation preview
LineaLEDINTERIOR - INTEGRAL POWER SUPPLY
ACTIVE WHITE (TUNABLE)SHAPING THE EXPERIENCE OF LIGHT
Insight Lighting www.insightlighting.com
September 20, 2016 11:26 AM1 of 7
CIRCUIT LIMITATIONS • 1600 watts at 120 VAC, (33) 48 watt drivers at full load – One driver per fixture • 2800 watts at 277 VAC, (58) 48 watt drivers at full load- One driver per fixture
ITEM SPECIFICATION
LIGHT SOURCE 12W/FT
OPTICS
COLOR TEMPERATURES ACTIVE WHITE COLOR TEMPERATURE TUNING FROM 27K - 65K
CRI 83
PERFORMANCE ACTIVE WHITE (4000K) - 48" FIXTURE
FIXTURE WATTAGE(TOTAL WATTAGE)
OPTICS LUMENS EFFICACY lm/W
12.0 W/FT 100° 4004 91 lm/W
3.5W/ft fixture meets current ASHRAE requirements
LUMEN MAINTENANCE 75,000 hrs L70
ELECTRICAL AC LINE VOLTAGE 120V, 240V, 277V
POWER SUPPLY INTEGRAL TO THE LUMINAIRE
CONTROL DMX READY DMX Fixture Resolution
PHYSICAL HOUSING Extruded aluminum housing with tooledend caps, powder-coat finish
DIMENSIONS 2-3/4" Diameter12" / 24" / 36" / 48" Single fixtures and multiple fixture run
LENS Standard Lens: Translucent acrylic snap-in tool-less lensOptional Lens: Diffuse Direct View Dome Lens (DV Option)
OPERATING TEMPERATURE -20° C to 40° C
CERTIFICATION ETL and cETL approved for Dry Location
RoHSCOMPLIANT
WARRANTY 5 YEAR LIMITED
All LineaLED products are tested to IES LM-79, LM-80 and ANSI C78.377A standards
LineaLEDINTERIOR - INTEGRAL POWER SUPPLY
ACTIVE WHITE (TUNABLE)SHAPING THE EXPERIENCE OF LIGHT
Insight Lighting www.insightlighting.com
September 20, 2016 11:26 AM2 of 7
LIN
STEP 1 - FIXTURE ORDERING INFORMATIONPrefix Wattage
W / FtLED
Color/CCTOptics Light
DirectionMounting Fixture
LengthVoltage/
Wiring MethodControl Options Finish
(Semi-Gloss)Options
LIN
LineaLEDSERIES
ACTIVE WHITE(KELVIN TUNABLE)
U = Uplight
D = Downlight
12" Fixtures
MPP = Mono-Point Pendant
SRS = Semi-Recessed
Single Fixtures
12"
INT1 = 120V integral power
INT2 = 277V integral power
DMXFX = DMX Fixture Resolution
DMX Controls are Required.
Order separately.
W = White
BL = Black
BR = Bronze
N = Natural
S = Satin
CC = Custom Color �
� Contact factory for
custom color. Additional
charges will apply.
DV = Diffused Direct View Lens
12 AWH 100°
WW(Wallwash)
Kelvin Tuning from 27K - 65K
24-48" Single Fixtures
CES = Close End
EAS-X = Extended Arm
ACS = Aircraft Cable
PNS-X = Pendant
SRS = Semi-Recessed
24-48" Single
Fixtures
24"
36"
48"
Multiple Fixture Run
CEM = Close End
EAM-X = Extended Arm
ACM = Aircraft Cable
PNM-X = Pendant
Multiple Fixture Run
Specify nominal run length in feet
• All Active White products require a DMX programmer for proper mixing. Must order separately.
• One LPT is required for field re-addressing of factory DMX settings. See below.
STEP 2 - ORDER DMX DISTRIBUTION & PROGRAMMING KITDMX DISTRIBUTION & PROGRAMMING KIT - REQUIRED FOR ALL COLOR CHANGING INSTALLATIONS
CATALOG NUMBER DESCRIPTION
LPT DMX PROGRAMMING TOOL: One LPT is required for field re-addressing of factory DMX settings.
CDS-A DMX DISTRIBUTION KIT ONLY (3 OUTPUTS): CDS-A consists of three outputs. Each output accommodates up to 32 fixtures in INT/REM wiring methods and unlimted fixtures in ACV wiring method.Four terminators are included for use as required.
LineaLEDINTERIOR - INTEGRAL POWER SUPPLY
ACTIVE WHITE (TUNABLE)SHAPING THE EXPERIENCE OF LIGHT
Insight Lighting www.insightlighting.com
September 20, 2016 11:26 AM3 of 7
Housing provided with finished steel mounting brackets attached to die-cast end plates with flush cap screws, allowing for ease of adjustment.Standard power feed location is on left side of fixture. If different power feed location is required, please request a modification.
CES - Close End Mount, Single Fixture
CEM - Close End Mount, Multiple Fixture Run
Nominal Length(START)
Nominal Length(MID)
Nominal Length(MID)
Nominal Length(MID)
Nominal Length(END)
OVER-ALL LENGTH
Sequence of fixtures must be identified in multiple fixture runs. Use table below to arrange Nominal Lengths of START, MID, and END fixtures to equal OVER-ALL desired length. *INSIGHT LIGHTING reserves the right to arrange fixtures as seen fit if sequence is not indentified by customer.*OVER-ALL LENGTH is Nominal; Refer to Mounting Table for exact fixture dimensions.
Nominal LengthSingle Fixture
24" 36" 48"
'A' 24-7/8" 36-7/8" 48-7/8"
'B' 23-1/2" 35-1/2" 47-1/2"
Nominal LengthSingle Fixture
24" 36" 48"
'A' 2' 3-3/4" 3' 3-3/4" 4' 3-3/4"
'B' 2' 1/2" 3' 1/2" 4' 1/2'
'C' 2' 1-1/2" 3' 1-1/2" 4' 1-1/2'
'D' 2' 2-3/4" 3' 2-3/4" 4' 2-3/4"
"B"
3"
"B"
"A"
60°Rotation
"D"
"B""D" "D" "C"
"C"
"A"
"D"
"A"
q q
1-1/2"
3-3/8"Power Feed
2-3/4"
Ø2-3/4"
"B"3-3/8"
1-1/2" TYP.
MountingBracket
Single Gang J-Box(by others)
Canopy
(2X) Clearanceholes for 1/4"
mounting hardware(by others)
MOUNTING DETAIL
Power Feed LocationSingle Gang J-Box (by others)
Power Feed
4"3/4"
3-1/2"
1-1/2"
Ø2-3/4"
60°ROTATION
TOP VIEW - CES MOUNT
BOTTOM VIEW - SMS MOUNT
TOP VIEW - CEM MOUNT
qq q"C"
4"
MountingBracket
Single Gang J-Box(by others)
Canopy
(2X) Clearanceholes for 1/4"
mounting hardware(by others)
"D"
3/4" TYP.
MOUNTING DETAIL
Power Feed LocationSingle Gang J-Box(by others)
Standard power feed location is on left side of fixture. If different power feed location is required, please request a modification.
"B"
3"
"B"
"A"
60°Rotation
"D"
"B""D" "D" "C"
"C"
"A"
"D"
"A"
q q
1-1/2"
3-3/8"Power Feed
2-3/4"
Ø2-3/4"
"B"3-3/8"
1-1/2" TYP.
MountingBracket
Single Gang J-Box(by others)
Canopy
(2X) Clearanceholes for 1/4"
mounting hardware(by others)
MOUNTING DETAIL
Power Feed LocationSingle Gang J-Box (by others)
Power Feed
4"3/4"
3-1/2"
1-1/2"
Ø2-3/4"
60°ROTATION
TOP VIEW - CES MOUNT
BOTTOM VIEW - SMS MOUNT
TOP VIEW - CEM MOUNT
qq q"C"
4"
MountingBracket
Single Gang J-Box(by others)
Canopy
(2X) Clearanceholes for 1/4"
mounting hardware(by others)
"D"
3/4" TYP.
MOUNTING DETAIL
Power Feed LocationSingle Gang J-Box(by others)
TOP VIEWMPP MOUNT
Ø4-1/8"
5-1/2"
40°Rotation
Ø4-1/8"
5-1/2"3"
40°Rotation
13"
BACK VIEWFRONT VIEW
TypicalJ-Box Installation(J-Box by others)
WALL MOUNT CEILING MOUNT
Rigid steel stem conceals leads and are painted to match luminaire. 4” diameter low profile canopy is provided as a standard. The canopy is painted to match luminaire unless otherwise specified.
MPP - Mono Point Pendant - Single 12" Fixture
LineaLEDINTERIOR - INTEGRAL POWER SUPPLY
ACTIVE WHITE (TUNABLE)SHAPING THE EXPERIENCE OF LIGHT
Insight Lighting www.insightlighting.com
September 20, 2016 11:26 AM4 of 7
EAS/EAM - Extended Arm Mount Single / Extended Arm Mount Multiple FixturesExtended arms are constructed of steel tubing welded to heavy gauge steel wall brackets. Mounting brackets, arms, and canopies are painted to match luminaire. All leads are concealed within the extended arms.
EAS - Extended Arm Mount, Single Fixture
EAM - Extended Arm Mount, Multiple Fixture Run
Nominal Length(START)
Nominal Length(MID)
Nominal Length(MID)
Nominal Length(MID)
Nominal Length(END)
OVER-ALL LENGTH
Sequence of fixtures must be identified in multiple fixture runs.Use table below to arrange Nominal Lengths of START, MID, and END fixtures to equal OVER-ALL desired length.
*INSIGHT LIGHTING reserves the right to arrange fixtures as seen fit if sequence is not indentified by customer.
*OVER-ALL LENGTH is Nominal; Refer to Mounting Table for exact fixture dimensions.
Standard power feed location is on left side of fixture. If different power feed location is required, please request a modification.
Standard power feed location is on left side of fixture. If different power feed loca-tion is required, please request a modification.
Nominal LengthSingle Fixture
24" 36" 48"
'A' 28-3/4" 40-3/4" 52/34"
'B' 26-3/4" 38-3/4" 50-3/4"
Nominal LengthSingle Fixture
24" 36" 48"
'A' 27-3/4" 39-3/4" 51-3/4"
'B' 26-3/4" 38-3/4" 50-3/4"
'C' 26-3/4" 38-3/4" 50-3/4"
"A"
"B"
"A"
J-Box (by others)
60°Rotation
Ø2-3/4"
SPECIFYMIN 6"
MAX 24"
"B"Ø5"CANOPY4-3/4"
Mounting Plate 4-1/8"
4-1/8"
J-Box (by others)
60°Rotation
Ø2-3/4"
SPECIFYMIN 6"
MAX 24"
2"(Typ.)
"C" "C" "C"
"A" "B"
"C" "C" "C"4-3/4"
Mounting Plate
Ø5"CANOPY
4-1/8"
4-1/8"
TOP VIEW - EAS MOUNT
TOP VIEW - EAM MOUNT
MOUNTING DETAIL
MOUNTING DETAIL
2"(Typ.)
Power-Feed Location 12" Input Lead Provided
Power-Feed Location 12" Input Lead Provided
"A"
"B"
"A"
J-Box (by others)
60°Rotation
Ø2-3/4"
SPECIFYMIN 6"
MAX 24"
"B"Ø5"CANOPY4-3/4"
Mounting Plate 4-1/8"
4-1/8"
J-Box (by others)
60°Rotation
Ø2-3/4"
SPECIFYMIN 6"
MAX 24"
2"(Typ.)
"C" "C" "C"
"A" "B"
"C" "C" "C"4-3/4"
Mounting Plate
Ø5"CANOPY
4-1/8"
4-1/8"
TOP VIEW - EAS MOUNT
TOP VIEW - EAM MOUNT
MOUNTING DETAIL
MOUNTING DETAIL
2"(Typ.)
Power-Feed Location 12" Input Lead Provided
Power-Feed Location 12" Input Lead Provided
LineaLEDINTERIOR - INTEGRAL POWER SUPPLY
ACTIVE WHITE (TUNABLE)SHAPING THE EXPERIENCE OF LIGHT
Insight Lighting www.insightlighting.com
September 20, 2016 11:26 AM5 of 7
ACS/ACM - Aircraft Cable Single / Aircraft Cable Multiple FixturesStainless steel adjustable aircraft cable attaches to rotatable castings on Luminaire housing with chrome plated, low profile cable grippers. 4” diameter low profile canopies are provided as a standard. All canopies are painted semi-gloss white unless otherwise specified.
Nominal Length(START)
Nominal Length(MID)
Nominal Length(MID)
Nominal Length(MID)
Nominal Length(END)
OVER-ALL LENGTH
Sequence of fixtures must be identified in multiple fixture runs.Use table below to arrange Nominal Lengths of START, MID, and END fixtures to equal OVER-ALL desired length.
*INSIGHT LIGHTING reserves the right to arrange fixtures as seen fit if sequence is not indentified by customer.
*OVER-ALL LENGTH is Nominal; Refer to Mounting Table for exact fixture dimensions.
ACS - Aircraft Cable Mount, Single Fixture
Standard power feed location is on left side of fixture. If different power feed loca-tion is required, please request a modification.
Provided with 10' of aircraft cable.
Nominal LengthSingle Fixture
24" 36" 48"
'A' 28-3/4" 40-3/4" 52-3/4"
'B' 26-3/4" 38-3/4" 50-3/4"
"A"
"A" "B" "A"
"C" "C" "C"
"C""C""C"
2"(TYP)
2"(TYP)
Ø4"CANOPY
Ø4"CANOPY
Ø2-3/4"
"B"
"B"
60°Rotation
FRONT VIEW - ACS MOUNT
FRONT VIEW - ACM MOUNT
Ø2-3/4"
60°Rotation
Power-Feed Location 12" Input Lead Provided
J-Box (by others)
J-Box (by others)
Power-Feed Location 12" Input Lead Provided
"A"
"A" "B" "A"
"C" "C" "C"
"C""C""C"
2"(TYP)
2"(TYP)
Ø4"CANOPY
Ø4"CANOPY
Ø2-3/4"
"B"
"B"
60°Rotation
FRONT VIEW - ACS MOUNT
FRONT VIEW - ACM MOUNT
Ø2-3/4"
60°Rotation
Power-Feed Location 12" Input Lead Provided
J-Box (by others)
J-Box (by others)
Power-Feed Location 12" Input Lead Provided
ACM - Aircraft Cable Mount, Multiple Fixture Run
Standard power feed location is on left side of fixture. If different power feed location is required, please request a modification.
Provided with 10' of aircraft cable.
Nominal LengthSingle Fixture
24" 36" 48"
'A' 27-3/4" 39-3/4" 51-3/4"
'B' 26-3/4" 38-3/4" 50-3/4"
'C' 26-3/4" 38-3/4" 50-3/4"
LineaLEDINTERIOR - INTEGRAL POWER SUPPLY
ACTIVE WHITE (TUNABLE)SHAPING THE EXPERIENCE OF LIGHT
Insight Lighting www.insightlighting.com
September 20, 2016 11:26 AM6 of 7
PNS/PNM - Pendant Mount Single / Pendant Mount Multiple FixturesRigid steel stems conceal all leads and are painted to match Luminaire. 4” diameter low profile canopies are provided as a standard. All canopies are painted semi-gloss white unless otherwise specified.
Nominal Length(START)
Nominal Length(MID)
Nominal Length(MID)
Nominal Length(MID)
Nominal Length(END)
OVER-ALL LENGTH
Sequence of fixtures must be identified in multiple fixture runs.Use table below to arrange Nominal Lengths of START, MID, and END fixtures to equal OVER-ALL desired length.
*INSIGHT LIGHTING reserves the right to arrange fixtures as seen fit if sequence is not indentified by customer.
*OVER-ALL LENGTH is Nominal; Refer to Mounting Table for exact fixture dimensions.
PNS - Pendant Mount, Single FixtureStandard power feed location is on left side of fixture. If different power feed location is required, please request a modification.
6" MIN.24" MAX.
(SPECIFY)
"B"
"A"
"C" "C" "C"
"A" "B" "A"
10" MIN.4' MAX.
(SPECIFY)
"B"
"C""C""C"
Ø4"CANOPY
FRONT VIEW - PNM MOUNT
2"(TYP)
Ø2-3/4"
FRONT VIEW - PNS MOUNT
Ø2-3/4"
2"(TYP)
Ø4"CANOPY
MOUNTING DETAIL
MOUNTING DETAIL
60°Rotation
60°Rotation
Power-Feed Location 12" Input Lead Provided
Power-Feed Location 12" Input Lead Provided
J-Box (by others)
J-Box (by others)
6" MIN.24" MAX.
(SPECIFY)
"B"
"A"
"C" "C" "C"
"A" "B" "A"
10" MIN.4' MAX.
(SPECIFY)
"B"
"C""C""C"
Ø4"CANOPY
FRONT VIEW - PNM MOUNT
2"(TYP)
Ø2-3/4"
FRONT VIEW - PNS MOUNT
Ø2-3/4"
2"(TYP)
Ø4"CANOPY
MOUNTING DETAIL
MOUNTING DETAIL
60°Rotation
60°Rotation
Power-Feed Location 12" Input Lead Provided
Power-Feed Location 12" Input Lead Provided
J-Box (by others)
J-Box (by others)
PNM - Pendant Mount, Multiple Fixture RunStandard power feed location is on left side of fixture. If different power feed location is required, please request a modification.
Nominal LengthSingle Fixture
24" 36" 48"
'A' 28-3/4" 40-3/4" 52-3/4"
'B' 26-3/4" 38-3/4" 50-3/4"
Nominal LengthSingle Fixture
24" 36" 48"
'A' 27-3/4" 39-3/4" 51-3/4"
'B' 26-3/4" 38-3/4" 50-3/4"
'C' 26-3/4" 38-3/4" 50-3/4"
LineaLEDINTERIOR - INTEGRAL POWER SUPPLY
ACTIVE WHITE (TUNABLE)SHAPING THE EXPERIENCE OF LIGHT
Insight Lighting www.insightlighting.com
September 20, 2016 11:26 AM7 of 7
SR - Semi-Recessed Single Fixtures
SRS - Semi-Recessed, Single Fixture
Nominal LengthSingle Fixture
12" 24" 36" 48"
'DIM. A' 15" 27" 39" 51"
'DIM. B' 13" 25" 37" 49"
'DIM. C' 14-1/8" 26-1/8" 38-1/8" 50-1/8"
LENGTH DIM "A" DIM "B" DIM "C"
2' 2'-3" 2'-1" 2'-2 1/8"3' 3'-3" 3'-1" 3'-2 1/8"4' 4'-3" 4'-1" 4'-2 1/8"
"DIM. A"OVERALL LENGTH
"DIM. B"LUMINAIRE LENGTH
"DIM. C"CUT OUT LENGTH
ELECTRICAL KNOCK-OUTS
Ø 2-3/4"
90°ROTATION
1-11/16"
5-3/16"ABOVE PLENUM
3-1/2"CUT OUT
THERMALPROTECTOR
Recommended