View
216
Download
0
Category
Preview:
Citation preview
8/22/2019 Lanco Amarkantak Power Ltd Korba Mechanical Vocational Training Report 1-Haxxo24 I~I
1/24
LANCO PROJECT
CHHATTISGARH INDIA
A Project Report on
the Partial Fulfillment of
Vocational Training on
TURBINE & GENERATOR DEC
Guided By:- Submitted By:-
Mr.K.D.N. Singh
8/22/2019 Lanco Amarkantak Power Ltd Korba Mechanical Vocational Training Report 1-Haxxo24 I~I
2/24
ACKNOWLEDGEMENT
The project bears imprints of many people. I take this opportunity to express my gratitude to all those
people who have been instrumental in the successful completion of this project.
I would like to show my greatest appreciation to Mr. K.D.N.Singh (HOD Turbine).I cant say thank you
enough for their tremendous support and help. I feel motivated and encouraged every time I attend their
meeting. Without their encouragement and guidance this project would not have materialized.
I would like to convey my special Thanks and gratitude to Mr.Sudip Banerjee Officer HR, for his
consistent support and guidance during the three weeks of vocational training. .
The guidance and support received from all the TG team members of Lanco infratech Ltd., including Mr.
Milind Bhajan & Mr. Vinit Pradhan was vital for the success of the project. I am thankful for their
constant support and help.
8/22/2019 Lanco Amarkantak Power Ltd Korba Mechanical Vocational Training Report 1-Haxxo24 I~I
3/24
INTRODUCTION
LANCO Power Ltd (LPL) is further setting up 2x660 MW Coal based power project near Pathadi- Saragbundia villages on the Champa - Korba State Highway in Chhattisgarh, India. Thecommissioning schedule of 36 months for Unit III and 40 Months for Unit IV categorizes these asfast track projects.
Upon attaining the required statutory clearances for Unit 3, the implementation of the projectwith supercritical technology started from 1 January 2010 as the zero date. Letter of Acceptancefor the supply of coal has been obtained for the third unit and Long Term Coal linkage has been
obtained for fourth unit. Power Finance Corporation, the lead lender for the project has already
appraised the project and the project is well poised to achieve financial closure shortly.
The ultimate capacity of the LANCO Power Plant after completion of Phase IV would be around1920 MW. |~|
Contact
CORPORATE OFFICELANCO Power LtdPlot No. 397, Phase-III,Udyog Vihar, Gurgaon - 122016
Haryana - India.Tel : +91-124 - 4741000/01/02/03Fax : +91-124 - 4741024Email:lapl@lancogroup.com
PROJECT OFFICE
LANCO Thermal Power StationVillage-Pathadi,P.O-TilkejaDist.- KorbaChhattisgarh-495 674, IndiaTel : 07759 279238,279123Fax : 07759 279370email :lapl@lancogroup.com
MISSION
Development of society through entrepreneurship.
VISION
Most admired integrated infrastructure enterprise.
mailto:lappl@lancogroup.commailto:lappl@lancogroup.commailto:lappl@lancogroup.commailto:lappl@lancogroup.commailto:lappl@lancogroup.commailto:lappl@lancogroup.commailto:lappl@lancogroup.commailto:lappl@lancogroup.com8/22/2019 Lanco Amarkantak Power Ltd Korba Mechanical Vocational Training Report 1-Haxxo24 I~I
4/24
INDEX
Content
1. Thermal Power Plant
2. History
3. Principal of Power Plant4. Efficiency
5. Boiler Steam Cycle
6. Feed Water heating & Deaerations
7. Super Heater
8. Re-Heater
9. Air Path
10.Turbine
11.Types Of Turbine12.Uses Of Turbine
13.Theory Of Operation
14.Condenser
15.Electrical Generator
8/22/2019 Lanco Amarkantak Power Ltd Korba Mechanical Vocational Training Report 1-Haxxo24 I~I
5/24
Thermal power station
A thermal power station is apower plantin which theprime moverissteamdriven. Water is heated,turns into steam and spins asteam turbinewhich drives anelectrical generator. After it passes through
the turbine, the steam iscondensedin acondenserand recycled to where it was heated; this is known asaRankine cycle. The greatest variation in the design of thermal power stations is due to the different fuel
sources. Some prefer to use the termenergy centerbecause such facilities convert formsofheatenergyinto electricity[1]. Some thermal power plants also deliver heat energy for industrial
purposes, fordistrict heating, or fordesalinationof water as well as delivering electrical power. A largepart of human CO2emissions comes from fossil fueled thermal power plants; efforts to reduce these
outputs are various and widespread.
History
Reciprocating steam engines have been used for mechanical power sources since the 18th Century, with
notable improvements being made byJames Watt. The very first commercial central electrical generating
stations in thePearl Street Station, New York and theHolborn Viaduct power station, London, in 1882,
also used reciprocating steam engines. The development of thesteam turbineallowed larger and more
efficient central generating stations to be built. By 1892 it was considered as an alternative to
reciprocating engines[2]Turbines offered higher speeds, more compact machinery, and stable speed
regulation allowing for parallel synchronous operation of generators on a common bus. Turbines entirely
replaced reciprocating engines in large central stations after about 1905. The largest reciprocating
engine-generator sets ever built were completed in 1901 for the Manhattan Elevated Railway. Each ofseventeen units weighed about 500 tons and was rated 6000 kilowatts; a contemporary turbine-set of
similar rating would have weighed about 20% as much.[3]|~|
Efficiency
The energy efficiency of a conventional thermal power station, considered as salable energy as a percent
of theheating valueof the fuel consumed, is typically 33% to 48%. This efficiency is limited as all heat
engines are governed by the laws ofthermodynamics. The rest of the energy must leave the plant in theform of heat. Thiswaste heatcan go through acondenserand be disposed of withcooling wateror
incooling towers. If the waste heat is instead utilized fordistrict heating, it is calledco-generation. An
important class of thermal power station are associated withdesalinationfacilities; these are typically
found in desert countries with large supplies ofnatural gasand in these plants, freshwater production and
electricity are equally important co-products.
http://en.wikipedia.org/wiki/Power_planthttp://en.wikipedia.org/wiki/Power_planthttp://en.wikipedia.org/wiki/Power_planthttp://en.wiktionary.org/wiki/prime_moverhttp://en.wiktionary.org/wiki/prime_moverhttp://en.wiktionary.org/wiki/prime_moverhttp://en.wikipedia.org/wiki/Steamhttp://en.wikipedia.org/wiki/Steamhttp://en.wikipedia.org/wiki/Steamhttp://en.wikipedia.org/wiki/Steam_turbinehttp://en.wikipedia.org/wiki/Steam_turbinehttp://en.wikipedia.org/wiki/Steam_turbinehttp://en.wikipedia.org/wiki/Electrical_generatorhttp://en.wikipedia.org/wiki/Electrical_generatorhttp://en.wikipedia.org/wiki/Electrical_generatorhttp://en.wikipedia.org/wiki/Condensationhttp://en.wikipedia.org/wiki/Condensationhttp://en.wikipedia.org/wiki/Condensationhttp://en.wikipedia.org/wiki/Surface_condenserhttp://en.wikipedia.org/wiki/Surface_condenserhttp://en.wikipedia.org/wiki/Surface_condenserhttp://en.wikipedia.org/wiki/Rankine_cyclehttp://en.wikipedia.org/wiki/Rankine_cyclehttp://en.wikipedia.org/wiki/Rankine_cyclehttp://en.wikipedia.org/wiki/Heathttp://en.wikipedia.org/wiki/Heathttp://en.wikipedia.org/wiki/Energyhttp://en.wikipedia.org/wiki/Energyhttp://en.wikipedia.org/wiki/Energyhttp://en.wikipedia.org/wiki/Thermal_power_station#cite_note-0http://en.wikipedia.org/wiki/Thermal_power_station#cite_note-0http://en.wikipedia.org/wiki/District_heatinghttp://en.wikipedia.org/wiki/District_heatinghttp://en.wikipedia.org/wiki/District_heatinghttp://en.wikipedia.org/wiki/Desalinationhttp://en.wikipedia.org/wiki/Desalinationhttp://en.wikipedia.org/wiki/Desalinationhttp://en.wikipedia.org/wiki/James_Watthttp://en.wikipedia.org/wiki/James_Watthttp://en.wikipedia.org/wiki/James_Watthttp://en.wikipedia.org/wiki/Pearl_Street_Stationhttp://en.wikipedia.org/wiki/Pearl_Street_Stationhttp://en.wikipedia.org/wiki/Pearl_Street_Stationhttp://en.wikipedia.org/wiki/Holborn_Viaduct_power_stationhttp://en.wikipedia.org/wiki/Holborn_Viaduct_power_stationhttp://en.wikipedia.org/wiki/Holborn_Viaduct_power_stationhttp://en.wikipedia.org/wiki/Steam_turbinehttp://en.wikipedia.org/wiki/Steam_turbinehttp://en.wikipedia.org/wiki/Steam_turbinehttp://en.wikipedia.org/wiki/Thermal_power_station#cite_note-1http://en.wikipedia.org/wiki/Thermal_power_station#cite_note-1http://en.wikipedia.org/wiki/Thermal_power_station#cite_note-1http://en.wikipedia.org/wiki/Thermal_power_station#cite_note-2http://en.wikipedia.org/wiki/Thermal_power_station#cite_note-2http://en.wikipedia.org/wiki/Thermal_power_station#cite_note-2http://en.wikipedia.org/wiki/Heating_valuehttp://en.wikipedia.org/wiki/Heating_valuehttp://en.wikipedia.org/wiki/Heating_valuehttp://en.wikipedia.org/wiki/Thermodynamichttp://en.wikipedia.org/wiki/Thermodynamichttp://en.wikipedia.org/wiki/Thermodynamichttp://en.wikipedia.org/wiki/Waste_heathttp://en.wikipedia.org/wiki/Waste_heathttp://en.wikipedia.org/wiki/Waste_heathttp://en.wikipedia.org/wiki/Surface_condenserhttp://en.wikipedia.org/wiki/Surface_condenserhttp://en.wikipedia.org/wiki/Surface_condenserhttp://en.wikipedia.org/wiki/Cooling_waterhttp://en.wikipedia.org/wiki/Cooling_waterhttp://en.wikipedia.org/wiki/Cooling_waterhttp://en.wikipedia.org/wiki/Cooling_towerhttp://en.wikipedia.org/wiki/Cooling_towerhttp://en.wikipedia.org/wiki/District_heatinghttp://en.wikipedia.org/wiki/District_heatinghttp://en.wikipedia.org/wiki/District_heatinghttp://en.wikipedia.org/wiki/Co-generationhttp://en.wikipedia.org/wiki/Co-generationhttp://en.wikipedia.org/wiki/Co-generationhttp://en.wikipedia.org/wiki/Desalinationhttp://en.wikipedia.org/wiki/Desalinationhttp://en.wikipedia.org/wiki/Desalinationhttp://en.wikipedia.org/wiki/Natural_gashttp://en.wikipedia.org/wiki/Natural_gashttp://en.wikipedia.org/wiki/Natural_gashttp://en.wikipedia.org/wiki/Natural_gashttp://en.wikipedia.org/wiki/Desalinationhttp://en.wikipedia.org/wiki/Co-generationhttp://en.wikipedia.org/wiki/District_heatinghttp://en.wikipedia.org/wiki/Cooling_towerhttp://en.wikipedia.org/wiki/Cooling_waterhttp://en.wikipedia.org/wiki/Surface_condenserhttp://en.wikipedia.org/wiki/Waste_heathttp://en.wikipedia.org/wiki/Thermodynamichttp://en.wikipedia.org/wiki/Heating_valuehttp://en.wikipedia.org/wiki/Thermal_power_station#cite_note-2http://en.wikipedia.org/wiki/Thermal_power_station#cite_note-1http://en.wikipedia.org/wiki/Steam_turbinehttp://en.wikipedia.org/wiki/Holborn_Viaduct_power_stationhttp://en.wikipedia.org/wiki/Pearl_Street_Stationhttp://en.wikipedia.org/wiki/James_Watthttp://en.wikipedia.org/wiki/Desalinationhttp://en.wikipedia.org/wiki/District_heatinghttp://en.wikipedia.org/wiki/Thermal_power_station#cite_note-0http://en.wikipedia.org/wiki/Energyhttp://en.wikipedia.org/wiki/Heathttp://en.wikipedia.org/wiki/Rankine_cyclehttp://en.wikipedia.org/wiki/Surface_condenserhttp://en.wikipedia.org/wiki/Condensationhttp://en.wikipedia.org/wiki/Electrical_generatorhttp://en.wikipedia.org/wiki/Steam_turbinehttp://en.wikipedia.org/wiki/Steamhttp://en.wiktionary.org/wiki/prime_moverhttp://en.wikipedia.org/wiki/Power_plant8/22/2019 Lanco Amarkantak Power Ltd Korba Mechanical Vocational Training Report 1-Haxxo24 I~I
6/24
ARankine cyclewith a two-stagesteam turbineand a single feed water heater.
Since the efficiency of the plant isfundamentally limitedby the ratio of the absolute temperatures of the
steam at turbine input and output, efficiency improvements require use of higher temperature, and
therefore higher pressure, steam. Historically, other working fluids such asmercuryhave been used in
amercury vapor turbinepower plant, since these can attain higher temperatures than water at lower
working pressures. However, the obvious hazards of toxicity, high cost, and poor heat transfer properties,
have ruled out mercury as a working fluid.
Above thecritical pointforwaterof 705 F (374 C) and 3212 psi (22.06 MPa), there is nophase
transitionfrom water to steam, but only a gradual decrease indensity.Boilingdoes not occur and it is not
possible to remove impurities via steam separation. In this case a super critical steam plant is required to
utilize the increasedthermodynamic efficiencyby operating at higher temperatures. These plants, also
called once-through plants because boiler water does not circulate multiple times, require additional water
purification steps to ensure that any impurities picked up during the cycle will be removed. This
purification takes the form of high pressure ion exchange units calledcondensate polishersbetween the
http://en.wikipedia.org/wiki/Rankine_cyclehttp://en.wikipedia.org/wiki/Rankine_cyclehttp://en.wikipedia.org/wiki/Rankine_cyclehttp://en.wikipedia.org/wiki/Steam_turbinehttp://en.wikipedia.org/wiki/Steam_turbinehttp://en.wikipedia.org/wiki/Steam_turbinehttp://en.wikipedia.org/wiki/Carnot_cyclehttp://en.wikipedia.org/wiki/Carnot_cyclehttp://en.wikipedia.org/wiki/Carnot_cyclehttp://en.wikipedia.org/wiki/Mercury_(element)http://en.wikipedia.org/wiki/Mercury_(element)http://en.wikipedia.org/wiki/Mercury_(element)http://en.wikipedia.org/wiki/Mercury_vapor_turbinehttp://en.wikipedia.org/wiki/Mercury_vapor_turbinehttp://en.wikipedia.org/wiki/Mercury_vapor_turbinehttp://en.wikipedia.org/wiki/Critical_point_(thermodynamics)http://en.wikipedia.org/wiki/Critical_point_(thermodynamics)http://en.wikipedia.org/wiki/Critical_point_(thermodynamics)http://en.wikipedia.org/wiki/Water_(data_page)http://en.wikipedia.org/wiki/Water_(data_page)http://en.wikipedia.org/wiki/Water_(data_page)http://en.wikipedia.org/wiki/Phase_transitionhttp://en.wikipedia.org/wiki/Phase_transitionhttp://en.wikipedia.org/wiki/Phase_transitionhttp://en.wikipedia.org/wiki/Phase_transitionhttp://en.wikipedia.org/wiki/Densityhttp://en.wikipedia.org/wiki/Densityhttp://en.wikipedia.org/wiki/Densityhttp://en.wikipedia.org/wiki/Boilinghttp://en.wikipedia.org/wiki/Boilinghttp://en.wikipedia.org/wiki/Boilinghttp://en.wikipedia.org/wiki/Thermodynamic_efficiencyhttp://en.wikipedia.org/wiki/Thermodynamic_efficiencyhttp://en.wikipedia.org/wiki/Thermodynamic_efficiencyhttp://en.wikipedia.org/wiki/Condensate_polisherhttp://en.wikipedia.org/wiki/Condensate_polisherhttp://en.wikipedia.org/wiki/Condensate_polisherhttp://en.wikipedia.org/wiki/File:Feedwater-heating.pnghttp://en.wikipedia.org/wiki/File:Feedwater-heating.pnghttp://en.wikipedia.org/wiki/File:Feedwater-heating.pnghttp://en.wikipedia.org/wiki/File:Feedwater-heating.pnghttp://en.wikipedia.org/wiki/Condensate_polisherhttp://en.wikipedia.org/wiki/Thermodynamic_efficiencyhttp://en.wikipedia.org/wiki/Boilinghttp://en.wikipedia.org/wiki/Densityhttp://en.wikipedia.org/wiki/Phase_transitionhttp://en.wikipedia.org/wiki/Phase_transitionhttp://en.wikipedia.org/wiki/Water_(data_page)http://en.wikipedia.org/wiki/Critical_point_(thermodynamics)http://en.wikipedia.org/wiki/Mercury_vapor_turbinehttp://en.wikipedia.org/wiki/Mercury_(element)http://en.wikipedia.org/wiki/Carnot_cyclehttp://en.wikipedia.org/wiki/Steam_turbinehttp://en.wikipedia.org/wiki/Rankine_cycle8/22/2019 Lanco Amarkantak Power Ltd Korba Mechanical Vocational Training Report 1-Haxxo24 I~I
7/24
steam condenser and the feed water heaters. Sub-critical fossil fuel power plants can achieve 3640%
efficiency.Super criticaldesigns have efficiencies in the low to mid 40% range, with new "ultra critical"
designs using pressures of 4400 psi (30.3 MPa) and dual stage reheat reaching about 48% efficiency.
Currentnuclear power plantsoperate below the temperatures and pressures that coal-fired plants do.
This limits their thermodynamic efficiency to 3032%. Some advanced reactor designs being studied,
such as theVery high temperature reactor,Advanced gas-cooled reactorandSuper critical water reactor,
would operate at temperatures and pressures similar to current coal plants, producing comparable
thermodynamic efficiency.
Boiler and steam cycle
In fossil-fueled power plants,steam generatorrefers to a furnace that burns the fossil fuel to boil water to
generate steam.
In thenuclear plantfield,steam generatorrefers to a specific type of largeheat exchangerused in
apressurized water reactor(PWR) to thermally connect the primary (reactor plant) and secondary (steam
plant) systems, which generates steam. In a nuclear reactor called aboiling water reactor(BWR), water is
boiled to generate steam directly in the reactor itself and there are no units called steam generators.
In some industrial settings, there can also be steam-producing heat exchangers called heat recovery
steam generators (HRSG) which utilize heat from some industrial process. The steam generating boiler
has to produce steam at the high purity, pressure and temperature required for the steam turbine that
drives the electrical generator.
Geothermal plantsneed no boiler since they use naturally occurring steam sources. Heat exchangers
may be used where the geothermal steam is very corrosive or contains excessive suspended solids.
A fossil fuel steam generator includes aneconomizer, asteam drum, and thefurnacewith its steam
generating tubes andsuper heatercoils. Necessarysafety valvesare located at suitable points to avoid
excessive boiler pressure. The air andflue gaspath equipment include: forced draft (FD)fan,Air
Preheater(AP), boiler furnace, induced draft (ID) fan, fly ash collectors (electrostatic
precipitatororbaghouse) and theflue gas stack.|~|
http://en.wikipedia.org/wiki/Super_critical_fluidhttp://en.wikipedia.org/wiki/Super_critical_fluidhttp://en.wikipedia.org/wiki/Super_critical_fluidhttp://en.wikipedia.org/wiki/Nuclear_power_planthttp://en.wikipedia.org/wiki/Nuclear_power_planthttp://en.wikipedia.org/wiki/Nuclear_power_planthttp://en.wikipedia.org/wiki/Very_high_temperature_reactorhttp://en.wikipedia.org/wiki/Very_high_temperature_reactorhttp://en.wikipedia.org/wiki/Very_high_temperature_reactorhttp://en.wikipedia.org/wiki/Advanced_gas-cooled_reactorhttp://en.wikipedia.org/wiki/Advanced_gas-cooled_reactorhttp://en.wikipedia.org/wiki/Advanced_gas-cooled_reactorhttp://en.wikipedia.org/w/index.php?title=Super_critical_water_reactor&action=edit&redlink=1http://en.wikipedia.org/w/index.php?title=Super_critical_water_reactor&action=edit&redlink=1http://en.wikipedia.org/w/index.php?title=Super_critical_water_reactor&action=edit&redlink=1http://en.wikipedia.org/wiki/Boiler_(steam_generator)http://en.wikipedia.org/wiki/Boiler_(steam_generator)http://en.wikipedia.org/wiki/Boiler_(steam_generator)http://en.wikipedia.org/wiki/Nuclear_powerhttp://en.wikipedia.org/wiki/Nuclear_powerhttp://en.wikipedia.org/wiki/Nuclear_powerhttp://en.wikipedia.org/wiki/Steam_generator_(nuclear_power)http://en.wikipedia.org/wiki/Steam_generator_(nuclear_power)http://en.wikipedia.org/wiki/Steam_generator_(nuclear_power)http://en.wikipedia.org/wiki/Heat_exchangerhttp://en.wikipedia.org/wiki/Heat_exchangerhttp://en.wikipedia.org/wiki/Heat_exchangerhttp://en.wikipedia.org/wiki/Pressurized_water_reactorhttp://en.wikipedia.org/wiki/Pressurized_water_reactorhttp://en.wikipedia.org/wiki/Pressurized_water_reactorhttp://en.wikipedia.org/wiki/Boiling_water_reactorhttp://en.wikipedia.org/wiki/Boiling_water_reactorhttp://en.wikipedia.org/wiki/Geothermal_powerhttp://en.wikipedia.org/wiki/Geothermal_powerhttp://en.wikipedia.org/wiki/Economizerhttp://en.wikipedia.org/wiki/Economizerhttp://en.wikipedia.org/wiki/Economizerhttp://en.wikipedia.org/wiki/Steam_drumhttp://en.wikipedia.org/wiki/Steam_drumhttp://en.wikipedia.org/wiki/Steam_drumhttp://en.wikipedia.org/wiki/Furnacehttp://en.wikipedia.org/wiki/Furnacehttp://en.wikipedia.org/wiki/Furnacehttp://en.wikipedia.org/w/index.php?title=Super_heater&action=edit&redlink=1http://en.wikipedia.org/w/index.php?title=Super_heater&action=edit&redlink=1http://en.wikipedia.org/w/index.php?title=Super_heater&action=edit&redlink=1http://en.wikipedia.org/wiki/Safety_valvehttp://en.wikipedia.org/wiki/Safety_valvehttp://en.wikipedia.org/wiki/Safety_valvehttp://en.wikipedia.org/wiki/Flue_gashttp://en.wikipedia.org/wiki/Flue_gashttp://en.wikipedia.org/wiki/Flue_gashttp://en.wikipedia.org/wiki/Centrifugal_fanhttp://en.wikipedia.org/wiki/Centrifugal_fanhttp://en.wikipedia.org/wiki/Centrifugal_fanhttp://en.wikipedia.org/w/index.php?title=Air_Preheater&action=edit&redlink=1http://en.wikipedia.org/w/index.php?title=Air_Preheater&action=edit&redlink=1http://en.wikipedia.org/w/index.php?title=Air_Preheater&action=edit&redlink=1http://en.wikipedia.org/w/index.php?title=Air_Preheater&action=edit&redlink=1http://en.wikipedia.org/wiki/Electrostatic_precipitatorhttp://en.wikipedia.org/wiki/Electrostatic_precipitatorhttp://en.wikipedia.org/wiki/Electrostatic_precipitatorhttp://en.wikipedia.org/wiki/Electrostatic_precipitatorhttp://en.wikipedia.org/wiki/Dust_collector#Fabric_filtershttp://en.wikipedia.org/wiki/Dust_collector#Fabric_filtershttp://en.wikipedia.org/wiki/Dust_collector#Fabric_filtershttp://en.wikipedia.org/wiki/Flue_gas_stackhttp://en.wikipedia.org/wiki/Flue_gas_stackhttp://en.wikipedia.org/wiki/Flue_gas_stackhttp://en.wikipedia.org/wiki/Flue_gas_stackhttp://en.wikipedia.org/wiki/Dust_collector#Fabric_filtershttp://en.wikipedia.org/wiki/Electrostatic_precipitatorhttp://en.wikipedia.org/wiki/Electrostatic_precipitatorhttp://en.wikipedia.org/w/index.php?title=Air_Preheater&action=edit&redlink=1http://en.wikipedia.org/w/index.php?title=Air_Preheater&action=edit&redlink=1http://en.wikipedia.org/wiki/Centrifugal_fanhttp://en.wikipedia.org/wiki/Flue_gashttp://en.wikipedia.org/wiki/Safety_valvehttp://en.wikipedia.org/w/index.php?title=Super_heater&action=edit&redlink=1http://en.wikipedia.org/wiki/Furnacehttp://en.wikipedia.org/wiki/Steam_drumhttp://en.wikipedia.org/wiki/Economizerhttp://en.wikipedia.org/wiki/Geothermal_powerhttp://en.wikipedia.org/wiki/Boiling_water_reactorhttp://en.wikipedia.org/wiki/Pressurized_water_reactorhttp://en.wikipedia.org/wiki/Heat_exchangerhttp://en.wikipedia.org/wiki/Steam_generator_(nuclear_power)http://en.wikipedia.org/wiki/Nuclear_powerhttp://en.wikipedia.org/wiki/Boiler_(steam_generator)http://en.wikipedia.org/w/index.php?title=Super_critical_water_reactor&action=edit&redlink=1http://en.wikipedia.org/wiki/Advanced_gas-cooled_reactorhttp://en.wikipedia.org/wiki/Very_high_temperature_reactorhttp://en.wikipedia.org/wiki/Nuclear_power_planthttp://en.wikipedia.org/wiki/Super_critical_fluid8/22/2019 Lanco Amarkantak Power Ltd Korba Mechanical Vocational Training Report 1-Haxxo24 I~I
8/24
Feed water heating and deaeration
The feed water used in thesteamboiler is a means of transferring heat energy from the burning fuel to
the mechanical energy of the spinningsteam turbine. The total feed water consists of
recirculated condensate water and purified makeup water. Because the metallic materials it contacts are
subject tocorrosionat high temperatures and pressures, the makeup water is highly purified before use.
A system ofwater softenersandion exchangedemineralizers produces water so pure that it
coincidentally becomes an electricalinsulator, withconductivityin the range of 0.31.0microsiemensper
centimeter. The makeup water in a 500 MWe plant amounts to perhaps 20 US gallons per minute (1.25
L/s) to offset the small losses from steam leaks in the system.
The feed water cycle begins with condensate water being pumped out of thecondenserafter traveling
through the steam turbines. The condensate flow rate at full load in a 500 MW plant is about 6,000 US
gallons per minute (400 L/s).
Diagram of boiler feed water deaerator (with vertical, domed aeration section and horizontal water storage section
The water flows through a series of six or seven intermediatefeed water heaters, heated up at each point
with steam extracted from an appropriate duct on the turbines and gaining temperature at each stage.
Typically, the condensate plus the makeup water then flows through adeaerator[7][8]that removes
dissolved air from the water, further purifying and reducing its corrosiveness. The water may be dosed
following this point withhydrazine, a chemical that removes the remainingoxygenin the water to below
5parts per billion(ppb).[vague] It is also dosed withpHcontrol agents such asammoniaormorpholineto
keep the residualaciditylow and thus non-corrosive.
http://en.wikipedia.org/wiki/Steamhttp://en.wikipedia.org/wiki/Steamhttp://en.wikipedia.org/wiki/Steamhttp://en.wikipedia.org/wiki/Steam_turbinehttp://en.wikipedia.org/wiki/Steam_turbinehttp://en.wikipedia.org/wiki/Corrosionhttp://en.wikipedia.org/wiki/Corrosionhttp://en.wikipedia.org/wiki/Corrosionhttp://en.wikipedia.org/wiki/Water_softenerhttp://en.wikipedia.org/wiki/Water_softenerhttp://en.wikipedia.org/wiki/Water_softenerhttp://en.wikipedia.org/wiki/Ion_exchangehttp://en.wikipedia.org/wiki/Ion_exchangehttp://en.wikipedia.org/wiki/Ion_exchangehttp://en.wikipedia.org/wiki/Electrical_insulationhttp://en.wikipedia.org/wiki/Electrical_insulationhttp://en.wikipedia.org/wiki/Electrical_insulationhttp://en.wikipedia.org/wiki/Electrical_conductivityhttp://en.wikipedia.org/wiki/Electrical_conductivityhttp://en.wikipedia.org/wiki/Electrical_conductivityhttp://en.wikipedia.org/wiki/Siemens_(unit)#Definitionhttp://en.wikipedia.org/wiki/Siemens_(unit)#Definitionhttp://en.wikipedia.org/wiki/Siemens_(unit)#Definitionhttp://en.wikipedia.org/wiki/Surface_condenserhttp://en.wikipedia.org/wiki/Surface_condenserhttp://en.wikipedia.org/wiki/Surface_condenserhttp://en.wikipedia.org/w/index.php?title=Feed_water_heater&action=edit&redlink=1http://en.wikipedia.org/w/index.php?title=Feed_water_heater&action=edit&redlink=1http://en.wikipedia.org/w/index.php?title=Feed_water_heater&action=edit&redlink=1http://en.wikipedia.org/wiki/Deaeratorhttp://en.wikipedia.org/wiki/Deaeratorhttp://en.wikipedia.org/wiki/Deaeratorhttp://en.wikipedia.org/wiki/Thermal_power_station#cite_note-7http://en.wikipedia.org/wiki/Thermal_power_station#cite_note-7http://en.wikipedia.org/wiki/Hydrazinehttp://en.wikipedia.org/wiki/Hydrazinehttp://en.wikipedia.org/wiki/Hydrazinehttp://en.wikipedia.org/wiki/Oxygenhttp://en.wikipedia.org/wiki/Oxygenhttp://en.wikipedia.org/wiki/Oxygenhttp://en.wikipedia.org/wiki/Parts_per_billionhttp://en.wikipedia.org/wiki/Parts_per_billionhttp://en.wikipedia.org/wiki/Parts_per_billionhttp://en.wikipedia.org/wiki/Wikipedia:Vaguenesshttp://en.wikipedia.org/wiki/Wikipedia:Vaguenesshttp://en.wikipedia.org/wiki/Wikipedia:Vaguenesshttp://en.wikipedia.org/wiki/PHhttp://en.wikipedia.org/wiki/PHhttp://en.wikipedia.org/wiki/PHhttp://en.wikipedia.org/wiki/Ammoniahttp://en.wikipedia.org/wiki/Ammoniahttp://en.wikipedia.org/wiki/Ammoniahttp://en.wikipedia.org/wiki/Morpholinehttp://en.wikipedia.org/wiki/Morpholinehttp://en.wikipedia.org/wiki/Morpholinehttp://en.wikipedia.org/wiki/Acidhttp://en.wikipedia.org/wiki/Acidhttp://en.wikipedia.org/wiki/Acidhttp://en.wikipedia.org/wiki/File:Deaerator.pnghttp://en.wikipedia.org/wiki/File:Deaerator.pnghttp://en.wikipedia.org/wiki/File:Deaerator.pnghttp://en.wikipedia.org/wiki/File:Deaerator.pnghttp://en.wikipedia.org/wiki/Acidhttp://en.wikipedia.org/wiki/Morpholinehttp://en.wikipedia.org/wiki/Ammoniahttp://en.wikipedia.org/wiki/PHhttp://en.wikipedia.org/wiki/Wikipedia:Vaguenesshttp://en.wikipedia.org/wiki/Parts_per_billionhttp://en.wikipedia.org/wiki/Oxygenhttp://en.wikipedia.org/wiki/Hydrazinehttp://en.wikipedia.org/wiki/Thermal_power_station#cite_note-7http://en.wikipedia.org/wiki/Deaeratorhttp://en.wikipedia.org/wiki/Deaeratorhttp://en.wikipedia.org/w/index.php?title=Feed_water_heater&action=edit&redlink=1http://en.wikipedia.org/wiki/Surface_condenserhttp://en.wikipedia.org/wiki/Siemens_(unit)#Definitionhttp://en.wikipedia.org/wiki/Electrical_conductivityhttp://en.wikipedia.org/wiki/Electrical_insulationhttp://en.wikipedia.org/wiki/Ion_exchangehttp://en.wikipedia.org/wiki/Water_softenerhttp://en.wikipedia.org/wiki/Corrosionhttp://en.wikipedia.org/wiki/Steam_turbinehttp://en.wikipedia.org/wiki/Steam8/22/2019 Lanco Amarkantak Power Ltd Korba Mechanical Vocational Training Report 1-Haxxo24 I~I
9/24
Super heater
Fossil fuel power plants can have asuper heaterand/or re-heater section in the steam generating
furnace. In a fossil fuel plant, after the steam is conditioned by the drying equipment inside the steam
drum, it is piped from the upper drum area into tubes inside an area of the furnace known as thesuper
heater, which has an elaborate set up of tubing where the steam vapor picks up more energy from hot
flue gases outside the tubing and its temperature is now superheated above the saturation temperature.
The superheated steam is then piped through the main steam lines to the valves before the high pressure
turbine.
Nuclear-powered steam plants do not have such sections but produce steam at essentially saturated
conditions. Experimental nuclear plants were equipped with fossil-fired super heaters in an attempt to
improve overall plant operating cost.
Re heater
Power plant furnaces may have a re heater section containing tubes heated by hot f lue gases outside the
tubes. Exhaust steam from the high pressure turbine is rerouted to go inside the re heater tubes to pickup
more energy to go drive intermediate or lower pressure turbines.
Air path
External fans are provided to give sufficient air for combustion. The forced draft fan takes air from the
atmosphere and, first warming it in the air preheater for better combustion, injects it via the air nozzles on
the furnace wall.
The induced draft fan assists the FD fan by drawing out combustible gases from the furnace, maintaining
a slightly negative pressure in the furnace to avoid backfiring through any opening.
http://en.wikipedia.org/w/index.php?title=Super_heater&action=edit&redlink=1http://en.wikipedia.org/w/index.php?title=Super_heater&action=edit&redlink=1http://en.wikipedia.org/w/index.php?title=Super_heater&action=edit&redlink=1http://en.wikipedia.org/w/index.php?title=Super_heater&action=edit&redlink=1http://en.wikipedia.org/w/index.php?title=Super_heater&action=edit&redlink=1http://en.wikipedia.org/w/index.php?title=Super_heater&action=edit&redlink=1http://en.wikipedia.org/w/index.php?title=Super_heater&action=edit&redlink=1http://en.wikipedia.org/w/index.php?title=Super_heater&action=edit&redlink=1http://en.wikipedia.org/w/index.php?title=Super_heater&action=edit&redlink=1http://en.wikipedia.org/w/index.php?title=Super_heater&action=edit&redlink=18/22/2019 Lanco Amarkantak Power Ltd Korba Mechanical Vocational Training Report 1-Haxxo24 I~I
10/24
TURBINE
A turbine is a rotaryenginethat extractsenergyfrom afluidflow and converts it into usefulwork.
The simplest turbines have one moving part, a rotor assembly, which is a shaft or drum with blades
attached. Moving fluid acts on the blades, or the blades react to the flow, so that they move and impart
rotational energy to the rotor. Early turbine examples arewindmillsandwater wheels.
Gas,steam, andwaterturbines usually have a casing around the blades that contains and controls the
working fluid. Credit for invention of the steam turbine is given both to the British engineerSir Charles
Parsons(18541931), for invention of thereaction turbineand to Swedish engineerGustaf de
Laval(18451913), for invention of theimpulse turbine. Modern steam turbines frequently employ both
reaction and impulse in the same unit, typically varying the degree of reaction and impulse from the blade
root to its periphery.
A device similar to a turbine but operating in reverse, i.e., driven, is acompressororpump. Theaxial
compressorin manygas turbineengines is a common example. Here again, both reaction and impulse
are employed and again, in modern axial compressors, the degree of reaction and impulse typically vary
from the blade root to its periphery.
Claude Burdincoined the term from theLatinturbo, orvortex, during an 1828 engineering
competition.Benoit Fourneyron, a student of Claude Burdin, built the first practical water turbine.|~|
http://en.wikipedia.org/wiki/Enginehttp://en.wikipedia.org/wiki/Enginehttp://en.wikipedia.org/wiki/Enginehttp://en.wikipedia.org/wiki/Energyhttp://en.wikipedia.org/wiki/Energyhttp://en.wikipedia.org/wiki/Energyhttp://en.wikipedia.org/wiki/Fluidhttp://en.wikipedia.org/wiki/Fluidhttp://en.wikipedia.org/wiki/Fluidhttp://en.wikipedia.org/wiki/Work_(physics)http://en.wikipedia.org/wiki/Work_(physics)http://en.wikipedia.org/wiki/Work_(physics)http://en.wikipedia.org/wiki/Windmillhttp://en.wikipedia.org/wiki/Windmillhttp://en.wikipedia.org/wiki/Windmillhttp://en.wikipedia.org/wiki/Water_wheelhttp://en.wikipedia.org/wiki/Water_wheelhttp://en.wikipedia.org/wiki/Water_wheelhttp://en.wikipedia.org/wiki/Gas_turbinehttp://en.wikipedia.org/wiki/Gas_turbinehttp://en.wikipedia.org/wiki/Steam_turbinehttp://en.wikipedia.org/wiki/Steam_turbinehttp://en.wikipedia.org/wiki/Steam_turbinehttp://en.wikipedia.org/wiki/Water_turbinehttp://en.wikipedia.org/wiki/Water_turbinehttp://en.wikipedia.org/wiki/Water_turbinehttp://en.wikipedia.org/wiki/Charles_Algernon_Parsonshttp://en.wikipedia.org/wiki/Charles_Algernon_Parsonshttp://en.wikipedia.org/wiki/Charles_Algernon_Parsonshttp://en.wikipedia.org/wiki/Charles_Algernon_Parsonshttp://en.wikipedia.org/wiki/Reaction_turbinehttp://en.wikipedia.org/wiki/Reaction_turbinehttp://en.wikipedia.org/wiki/Reaction_turbinehttp://en.wikipedia.org/wiki/Gustaf_de_Lavalhttp://en.wikipedia.org/wiki/Gustaf_de_Lavalhttp://en.wikipedia.org/wiki/Gustaf_de_Lavalhttp://en.wikipedia.org/wiki/Gustaf_de_Lavalhttp://en.wikipedia.org/wiki/Impulse_turbinehttp://en.wikipedia.org/wiki/Impulse_turbinehttp://en.wikipedia.org/wiki/Impulse_turbinehttp://en.wikipedia.org/wiki/Gas_compressorhttp://en.wikipedia.org/wiki/Gas_compressorhttp://en.wikipedia.org/wiki/Gas_compressorhttp://en.wikipedia.org/wiki/Pumphttp://en.wikipedia.org/wiki/Pumphttp://en.wikipedia.org/wiki/Pumphttp://en.wikipedia.org/wiki/Axial_compressorhttp://en.wikipedia.org/wiki/Axial_compressorhttp://en.wikipedia.org/wiki/Axial_compressorhttp://en.wikipedia.org/wiki/Axial_compressorhttp://en.wikipedia.org/wiki/Gas_turbinehttp://en.wikipedia.org/wiki/Gas_turbinehttp://en.wikipedia.org/wiki/Gas_turbinehttp://en.wikipedia.org/wiki/Claude_Burdinhttp://en.wikipedia.org/wiki/Claude_Burdinhttp://en.wikipedia.org/wiki/Latinhttp://en.wikipedia.org/wiki/Latinhttp://en.wikipedia.org/wiki/Latinhttp://en.wikipedia.org/wiki/Vortexhttp://en.wikipedia.org/wiki/Vortexhttp://en.wikipedia.org/wiki/Vortexhttp://en.wikipedia.org/wiki/Benoit_Fourneyronhttp://en.wikipedia.org/wiki/Benoit_Fourneyronhttp://en.wikipedia.org/wiki/Benoit_Fourneyronhttp://en.wikipedia.org/wiki/Benoit_Fourneyronhttp://en.wikipedia.org/wiki/Vortexhttp://en.wikipedia.org/wiki/Latinhttp://en.wikipedia.org/wiki/Claude_Burdinhttp://en.wikipedia.org/wiki/Gas_turbinehttp://en.wikipedia.org/wiki/Axial_compressorhttp://en.wikipedia.org/wiki/Axial_compressorhttp://en.wikipedia.org/wiki/Pumphttp://en.wikipedia.org/wiki/Gas_compressorhttp://en.wikipedia.org/wiki/Impulse_turbinehttp://en.wikipedia.org/wiki/Gustaf_de_Lavalhttp://en.wikipedia.org/wiki/Gustaf_de_Lavalhttp://en.wikipedia.org/wiki/Reaction_turbinehttp://en.wikipedia.org/wiki/Charles_Algernon_Parsonshttp://en.wikipedia.org/wiki/Charles_Algernon_Parsonshttp://en.wikipedia.org/wiki/Water_turbinehttp://en.wikipedia.org/wiki/Steam_turbinehttp://en.wikipedia.org/wiki/Gas_turbinehttp://en.wikipedia.org/wiki/Water_wheelhttp://en.wikipedia.org/wiki/Windmillhttp://en.wikipedia.org/wiki/Work_(physics)http://en.wikipedia.org/wiki/Fluidhttp://en.wikipedia.org/wiki/Energyhttp://en.wikipedia.org/wiki/Engine8/22/2019 Lanco Amarkantak Power Ltd Korba Mechanical Vocational Training Report 1-Haxxo24 I~I
11/24
TYPES OF TURBINE
Steam turbinesare used for the generation of electricity in thermal power plants, such as plants
usingcoal,fuel oilornuclear power. They were once used to directly drive mechanical devices such
as ships'propellers(e.g. theTurbinia), but most such applications now use reduction gears or an
intermediate electrical step, where the turbine is used to generate electricity, which then powers
anelectric motorconnected to the mechanical load. Turbo electric ship machinery was particularly
popular in the period immediately before and during WWII, primarily due to a lack of sufficient gear-
cutting facilities in US and UK shipyards.
Gas turbinesare sometimes referred to as turbine engines. Such engines usually feature an inlet, fan,
compressor, combustor and nozzle (possibly other assemblies) in addition to one or more turbines.
Transonicturbine. The gasflow in most turbines employed in gas turbine engines remains subsonic
throughout the expansion process. In a transonic turbine the gasflow becomes supersonic as it exits
the nozzle guide vanes, although the downstream velocities normally become subsonic. Transonic
turbines operate at a higher pressure ratio than normal but are usually less efficient and uncommon.
Contra-rotatingturbines. With axial turbines, some efficiency advantage can be obtained if a
downstream turbine rotates in the opposite direction to an upstream unit. However, the complicationcan be counter-productive. A contra-rotating steam turbine, usually known as the Ljungstrm turbine,
was originally invented by Swedish EngineerFredrik Ljungstrm(18751964), in Stockholm and in
partnership with his brotherBirger Ljungstrmhe obtained a patent in 1894. The design is essentially
a multi-stage radial turbine (or pair of 'nested' turbine rotors) offering great efficiency, four times as
large heat drop per stage as in the reaction (Parsons) turbine, extremely compact design and the type
met particular success in backpressure power plants. However, contrary to other designs, large
steam volumes are handled with difficulty and only a combination with axial flow turbines (DUREX)
admits the turbine to be built for power greater than ca 50 MW. In marine applications only about 50
turbo-electric units were ordered (of which a considerable amount were finally sold to land plants)
during 1917-19, and during 1920-22 a few turbo-mechanic not very successful units were sold.[1]Only
a few turbo-electric marine plants were still in use in the late 1960s (ss Ragne, ss Regin) while most
land plants remain in use 2010.
http://en.wikipedia.org/wiki/Steam_turbinehttp://en.wikipedia.org/wiki/Steam_turbinehttp://en.wikipedia.org/wiki/Coalhttp://en.wikipedia.org/wiki/Coalhttp://en.wikipedia.org/wiki/Coalhttp://en.wikipedia.org/wiki/Fuel_oilhttp://en.wikipedia.org/wiki/Fuel_oilhttp://en.wikipedia.org/wiki/Fuel_oilhttp://en.wikipedia.org/wiki/Nuclear_powerhttp://en.wikipedia.org/wiki/Nuclear_powerhttp://en.wikipedia.org/wiki/Nuclear_powerhttp://en.wikipedia.org/wiki/Propellerhttp://en.wikipedia.org/wiki/Propellerhttp://en.wikipedia.org/wiki/Propellerhttp://en.wikipedia.org/wiki/Turbiniahttp://en.wikipedia.org/wiki/Turbiniahttp://en.wikipedia.org/wiki/Turbiniahttp://en.wikipedia.org/wiki/Electric_motorhttp://en.wikipedia.org/wiki/Electric_motorhttp://en.wikipedia.org/wiki/Electric_motorhttp://en.wikipedia.org/wiki/Gas_turbinehttp://en.wikipedia.org/wiki/Gas_turbinehttp://en.wikipedia.org/wiki/Transonichttp://en.wikipedia.org/wiki/Transonichttp://en.wikipedia.org/wiki/Contra-rotatinghttp://en.wikipedia.org/wiki/Contra-rotatinghttp://en.wikipedia.org/wiki/Fredrik_Ljungstr%C3%B6mhttp://en.wikipedia.org/wiki/Fredrik_Ljungstr%C3%B6mhttp://en.wikipedia.org/wiki/Fredrik_Ljungstr%C3%B6mhttp://en.wikipedia.org/w/index.php?title=Birger_Ljungstr%C3%B6m&action=edit&redlink=1http://en.wikipedia.org/w/index.php?title=Birger_Ljungstr%C3%B6m&action=edit&redlink=1http://en.wikipedia.org/w/index.php?title=Birger_Ljungstr%C3%B6m&action=edit&redlink=1http://en.wikipedia.org/wiki/Turbine#cite_note-0http://en.wikipedia.org/wiki/Turbine#cite_note-0http://en.wikipedia.org/wiki/Turbine#cite_note-0http://en.wikipedia.org/wiki/Turbine#cite_note-0http://en.wikipedia.org/w/index.php?title=Birger_Ljungstr%C3%B6m&action=edit&redlink=1http://en.wikipedia.org/wiki/Fredrik_Ljungstr%C3%B6mhttp://en.wikipedia.org/wiki/Contra-rotatinghttp://en.wikipedia.org/wiki/Transonichttp://en.wikipedia.org/wiki/Gas_turbinehttp://en.wikipedia.org/wiki/Electric_motorhttp://en.wikipedia.org/wiki/Turbiniahttp://en.wikipedia.org/wiki/Propellerhttp://en.wikipedia.org/wiki/Nuclear_powerhttp://en.wikipedia.org/wiki/Fuel_oilhttp://en.wikipedia.org/wiki/Coalhttp://en.wikipedia.org/wiki/Steam_turbine8/22/2019 Lanco Amarkantak Power Ltd Korba Mechanical Vocational Training Report 1-Haxxo24 I~I
12/24
Statorlessturbine. Multi-stage turbines have a set of static (meaning stationary) inlet guide vanes that
direct the gasflow onto the rotating rotor blades. In a statorless turbine the gasflow exiting an
upstream rotor impinges onto a downstream rotor without an intermediate set of stator vanes (that
rearrange the pressure/velocity energy levels of the flow) being encountered.
Ceramicturbine. Conventional high-pressure turbine blades (and vanes) are made from nickel based
alloys and often utilise intricate internal air-cooling passages to prevent the metal from overheating. In
recent years, experimental ceramic blades have been manufactured and tested in gas turbines, with
a view to increasing Rotor Inlet Temperatures and/or, possibly, eliminating aircooling. Ceramic blades
are more brittle than their metallic counterparts, and carry a greater risk of catastrophic blade failure.
This has tended to limit their use in jet engines and gas turbines, to the stator (stationary) blades.
Shroudedturbine. Many turbine rotor blades have shrouding at the top, which interlocks with that of
adjacent blades, to increase damping and thereby reduce blade flutter. In large land-based electricity
generation steam turbines, the shrouding is often complemented, especially in the long blades of a
low-pressure turbine, with lacing wires. These wires pass through holes drilled in the blades at
suitable distances from the blade root and are usually brazed to the blades at the point where they
pass through. Lacing wires reduce blade flutter in the central part of the blades. The introduction of
lacing wires substantially reduces the instances of blade failure in large or low-pressure turbines.
Shroudless turbine. Modern practice is, wherever possible, to eliminate the rotorshrouding, thus
reducing thecentrifugalload on the blade and the cooling requirements.
Bladeless turbineuses the boundary layer effect and not a fluid impinging upon the blades as in a
conventional turbine.
Water turbines
Pelton turbine, a type of impulse water turbine.
Francis turbine, a type of widely used water turbine.
Kaplan turbine, a variation of the Francis Turbine.
Wind turbine. These normally operate as a single stage without nozzle and interstage guide vanes.
An exception is theolienne Bolle, which has a stator and a rotor, thus being a true turbine.
http://en.wikipedia.org/wiki/Statorhttp://en.wikipedia.org/wiki/Statorhttp://en.wikipedia.org/wiki/Ceramichttp://en.wikipedia.org/wiki/Ceramichttp://en.wikipedia.org/wiki/Ducted_fanhttp://en.wikipedia.org/wiki/Ducted_fanhttp://en.wikipedia.org/wiki/Ducted_fanhttp://en.wikipedia.org/wiki/Ducted_fanhttp://en.wikipedia.org/wiki/Shroudinghttp://en.wikipedia.org/wiki/Shroudinghttp://en.wikipedia.org/wiki/Shroudinghttp://en.wikipedia.org/wiki/Centrifugalhttp://en.wikipedia.org/wiki/Centrifugalhttp://en.wikipedia.org/wiki/Centrifugalhttp://en.wikipedia.org/wiki/Tesla_turbinehttp://en.wikipedia.org/wiki/Tesla_turbinehttp://en.wikipedia.org/wiki/Water_turbinehttp://en.wikipedia.org/wiki/Water_turbinehttp://en.wikipedia.org/wiki/Pelton_wheelhttp://en.wikipedia.org/wiki/Pelton_wheelhttp://en.wikipedia.org/wiki/Francis_turbinehttp://en.wikipedia.org/wiki/Francis_turbinehttp://en.wikipedia.org/wiki/Kaplan_turbinehttp://en.wikipedia.org/wiki/Kaplan_turbinehttp://en.wikipedia.org/wiki/Wind_turbinehttp://en.wikipedia.org/wiki/Wind_turbinehttp://en.wikipedia.org/wiki/%C3%89olienne_Boll%C3%A9ehttp://en.wikipedia.org/wiki/%C3%89olienne_Boll%C3%A9ehttp://en.wikipedia.org/wiki/%C3%89olienne_Boll%C3%A9ehttp://en.wikipedia.org/wiki/%C3%89olienne_Boll%C3%A9ehttp://en.wikipedia.org/wiki/Wind_turbinehttp://en.wikipedia.org/wiki/Kaplan_turbinehttp://en.wikipedia.org/wiki/Francis_turbinehttp://en.wikipedia.org/wiki/Pelton_wheelhttp://en.wikipedia.org/wiki/Water_turbinehttp://en.wikipedia.org/wiki/Tesla_turbinehttp://en.wikipedia.org/wiki/Centrifugalhttp://en.wikipedia.org/wiki/Shroudinghttp://en.wikipedia.org/wiki/Ducted_fanhttp://en.wikipedia.org/wiki/Ducted_fanhttp://en.wikipedia.org/wiki/Ceramichttp://en.wikipedia.org/wiki/Stator8/22/2019 Lanco Amarkantak Power Ltd Korba Mechanical Vocational Training Report 1-Haxxo24 I~I
13/24
Uses of turbines
Almost allelectrical poweron Earth is produced with a turbine of some type. Very high efficiency steam
turbines harness about 40% of the thermal energy, with the rest exhausted as waste heat.
Mostjet enginesrely on turbines to supply mechanical work from their working fluid and fuel as do allnuclear ships and power plants.
Turbines are often part of a larger machine. Agas turbine, for example, may refer to an internal
combustion machine that contains a turbine, ducts, compressor, combustor, heat-exchanger, fan and (in
the case of one designed to produce electricity) an alternator. Combustion turbines and steam turbines
may be connected to machinery such as pumps and compressors, or may be used for propulsion of
ships, usually through an intermediate gearbox to reduce rotary speed.
Reciprocating piston engines such asaircraft enginescan use a turbine powered by their exhaust to drive
an intake-air compressor, a configuration known as aturbocharger(turbinesupercharger) or, colloquially,
a "turbo".
Turbines can have very high power density (i.e. the ratio of power to weight, or power to volume). This is
because of their ability to operate at very high speeds. TheSpace Shuttle's main engines
useturbopumps(machines consisting of a pump driven by a turbine engine) to feed the propellants (liquid
oxygen and liquid hydrogen) into the engine's combustion chamber. The liquid hydrogen turbopump is
slightly larger than an automobile engine (weighing approximately 700 lb) and produces nearly
70,000hp(52.2MW).
Turboexpandersare widely used as sources of refrigeration in industrial processes.
Wikimedia Commons has
media related to: Turbine
Military jet engines,as branch of gas turbines, have recently been used as primary flight controller in post-
stall flight using jet deflections that are also called thrust vectoring [7]. The U.S. FAA has also conducted
a study about civilizing such thrust vectoring systems to recover jetliners from catastrophes.
http://en.wikipedia.org/wiki/Electrical_powerhttp://en.wikipedia.org/wiki/Electrical_powerhttp://en.wikipedia.org/wiki/Electrical_powerhttp://en.wikipedia.org/wiki/Jet_enginehttp://en.wikipedia.org/wiki/Jet_enginehttp://en.wikipedia.org/wiki/Jet_enginehttp://en.wikipedia.org/wiki/Gas_turbinehttp://en.wikipedia.org/wiki/Gas_turbinehttp://en.wikipedia.org/wiki/Gas_turbinehttp://en.wikipedia.org/wiki/Aircraft_enginehttp://en.wikipedia.org/wiki/Aircraft_enginehttp://en.wikipedia.org/wiki/Aircraft_enginehttp://en.wikipedia.org/wiki/Turbochargerhttp://en.wikipedia.org/wiki/Turbochargerhttp://en.wikipedia.org/wiki/Turbochargerhttp://en.wikipedia.org/wiki/Superchargerhttp://en.wikipedia.org/wiki/Superchargerhttp://en.wikipedia.org/wiki/Superchargerhttp://en.wikipedia.org/wiki/Space_Shuttlehttp://en.wikipedia.org/wiki/Space_Shuttlehttp://en.wikipedia.org/wiki/Space_Shuttlehttp://en.wikipedia.org/wiki/Turbopumphttp://en.wikipedia.org/wiki/Turbopumphttp://en.wikipedia.org/wiki/Turbopumphttp://en.wikipedia.org/wiki/Horsepowerhttp://en.wikipedia.org/wiki/Horsepowerhttp://en.wikipedia.org/wiki/Horsepowerhttp://en.wikipedia.org/wiki/Megawatthttp://en.wikipedia.org/wiki/Megawatthttp://en.wikipedia.org/wiki/Megawatthttp://en.wikipedia.org/wiki/Turboexpanderhttp://en.wikipedia.org/wiki/Turboexpanderhttp://commons.wikimedia.org/wiki/Category:Turbineshttp://commons.wikimedia.org/wiki/Category:Turbineshttp://commons.wikimedia.org/wiki/Category:Turbineshttp://commons.wikimedia.org/wiki/Category:Turbineshttp://en.wikipedia.org/wiki/Turboexpanderhttp://en.wikipedia.org/wiki/Megawatthttp://en.wikipedia.org/wiki/Horsepowerhttp://en.wikipedia.org/wiki/Turbopumphttp://en.wikipedia.org/wiki/Space_Shuttlehttp://en.wikipedia.org/wiki/Superchargerhttp://en.wikipedia.org/wiki/Turbochargerhttp://en.wikipedia.org/wiki/Aircraft_enginehttp://en.wikipedia.org/wiki/Gas_turbinehttp://en.wikipedia.org/wiki/Jet_enginehttp://en.wikipedia.org/wiki/Electrical_power8/22/2019 Lanco Amarkantak Power Ltd Korba Mechanical Vocational Training Report 1-Haxxo24 I~I
14/24
Theory of operation
A working fluid containspotential energy(pressurehead) andkinetic energy(velocity head). The fluid may
becompressibleorincompressible. Several physical principles are employed by turbines to collect this
energy:
Impulseturbines
These turbines change the direction of flow of a high velocity fluid or gas jet. The resulting
impulse spins the turbine and leaves the fluid flow with diminished kinetic energy. There is no
pressure change of the fluid or gas in the turbine blades (the moving blades), as in the case of a
steam or gas turbine, all the pressure drop takes place in the stationary blades (the nozzles).
Before reaching the turbine, the fluid'spressure headis changed to velocity headby accelerating
the fluid with anozzle.Pelton wheelsandde Laval turbinesuse this process exclusively. Impulse
turbines do not require a pressure casement around the rotor since the fluid jet is created by the
nozzle prior to reaching the blading on the rotor.Newton's second lawdescribes the transfer of
energy for impulse turbines.
Reactionturbines
These turbines developtorqueby reacting to the gas or fluid's pressure or mass. The pressure of
the gas or fluid changes as it passes through the turbine rotor blades. A pressure casement is
http://en.wikipedia.org/wiki/Potential_energyhttp://en.wikipedia.org/wiki/Potential_energyhttp://en.wikipedia.org/wiki/Potential_energyhttp://en.wikipedia.org/wiki/Head_(hydraulic)http://en.wikipedia.org/wiki/Head_(hydraulic)http://en.wikipedia.org/wiki/Head_(hydraulic)http://en.wikipedia.org/wiki/Kinetic_energyhttp://en.wikipedia.org/wiki/Kinetic_energyhttp://en.wikipedia.org/wiki/Kinetic_energyhttp://en.wikipedia.org/wiki/Compressibilityhttp://en.wikipedia.org/wiki/Compressibilityhttp://en.wikipedia.org/wiki/Compressibilityhttp://en.wikipedia.org/wiki/Incompressible_fluidhttp://en.wikipedia.org/wiki/Incompressible_fluidhttp://en.wikipedia.org/wiki/Incompressible_fluidhttp://en.wikipedia.org/wiki/Impulse_(physics)http://en.wikipedia.org/wiki/Impulse_(physics)http://en.wikipedia.org/wiki/Nozzlehttp://en.wikipedia.org/wiki/Nozzlehttp://en.wikipedia.org/wiki/Nozzlehttp://en.wikipedia.org/wiki/Pelton_wheelhttp://en.wikipedia.org/wiki/Pelton_wheelhttp://en.wikipedia.org/wiki/Pelton_wheelhttp://en.wikipedia.org/wiki/Steam_turbinehttp://en.wikipedia.org/wiki/Steam_turbinehttp://en.wikipedia.org/wiki/Steam_turbinehttp://en.wikipedia.org/wiki/Newton%27s_laws_of_motion#Newton.27s_second_lawhttp://en.wikipedia.org/wiki/Newton%27s_laws_of_motion#Newton.27s_second_lawhttp://en.wikipedia.org/wiki/Newton%27s_laws_of_motion#Newton.27s_second_lawhttp://en.wikipedia.org/wiki/Reaction_(physics)http://en.wikipedia.org/wiki/Reaction_(physics)http://en.wikipedia.org/wiki/Torquehttp://en.wikipedia.org/wiki/Torquehttp://en.wikipedia.org/wiki/Torquehttp://en.wikipedia.org/wiki/File:Turbines_impulse_v_reaction.pnghttp://en.wikipedia.org/wiki/Torquehttp://en.wikipedia.org/wiki/Reaction_(physics)http://en.wikipedia.org/wiki/Newton%27s_laws_of_motion#Newton.27s_second_lawhttp://en.wikipedia.org/wiki/Steam_turbinehttp://en.wikipedia.org/wiki/Pelton_wheelhttp://en.wikipedia.org/wiki/Nozzlehttp://en.wikipedia.org/wiki/Impulse_(physics)http://en.wikipedia.org/wiki/Incompressible_fluidhttp://en.wikipedia.org/wiki/Compressibilityhttp://en.wikipedia.org/wiki/Kinetic_energyhttp://en.wikipedia.org/wiki/Head_(hydraulic)http://en.wikipedia.org/wiki/Potential_energy8/22/2019 Lanco Amarkantak Power Ltd Korba Mechanical Vocational Training Report 1-Haxxo24 I~I
15/24
needed to contain the working fluid as it acts on the turbine stage(s) or the turbine must be fully
immersed in the fluid flow (such as with wind turbines). The casing contains and directs the
working fluid and, for water turbines, maintains the suction imparted by the draft tube.Francis
turbinesand moststeam turbinesuse this concept. For compressible working fluids, multiple
turbine stages are usually used to harness the expanding gas efficiently.Newton's third
lawdescribes the transfer of energy for reaction turbines.
In the case of steam turbines, such as would be used for marine applications or for land-based
electricity generation, a Parsons type reaction turbine would require approximately double the
number of blade rows as a de Laval type impulse turbine, for the same degree of thermal
energy conversion. Whilst this makes the Parsons turbine much longer and heavier, the overall
efficiency of a reaction turbine is slightly higher than the equivalent impulse turbine for the
same thermal energy conversion.
Steam turbines and later, gas turbines developed continually during the 20th Century, continue
to do so and in practice, modern turbine designs use both reaction and impulse concepts to
varying degrees whenever possible.Wind turbinesuse anairfoilto generateliftfrom the
moving fluid and impart it to the rotor (this is a form of reaction). Wind turbines also gain some
energy from the impulse of the wind, by deflecting it at an angle.Crossflow turbinesare
designed as an impulse machine, with a nozzle, but in low head applications maintain some
efficiency through reaction, like a traditional water wheel. Turbines with multiple stages may
utilize either reaction or impulse blading at high pressure. Steam Turbines were traditionally
more impulse but continue to move towards reaction designs similar to those used in GasTurbines. At low pressure the operating fluid medium expands in volume for small reductions
in pressure. Under these conditions (termed Low Pressure Turbines) blading becomes strictly
a reaction type design with the base of the blade solely impulse. The reason is due to the
effect of the rotation speed for each blade. As the volume increases, the blade height
increases, and the base of the blade spins at a slower speed relative to the tip. This change in
speed forces a designer to change from impulse at the base, to a high reaction style tip.
Classical turbine design methods were developed in the mid 19th century. Vector analysis
related the fluid flow with turbine shape and rotation. Graphical calculation methods were used
at first. Formulae for the basic dimensions of turbine parts are well documented and a highly
efficient machine can be reliably designed for any fluidflow condition. Some of the calculations
are empirical or 'rule of thumb' formulae, and others are based onclassical mechanics. As with
most engineering calculations, simplifying assumptions were made.|~|
http://en.wikipedia.org/wiki/Francis_turbinehttp://en.wikipedia.org/wiki/Francis_turbinehttp://en.wikipedia.org/wiki/Francis_turbinehttp://en.wikipedia.org/wiki/Francis_turbinehttp://en.wikipedia.org/wiki/Steam_turbinehttp://en.wikipedia.org/wiki/Steam_turbinehttp://en.wikipedia.org/wiki/Steam_turbinehttp://en.wikipedia.org/wiki/Newton%27s_laws_of_motion#Newton.27s_third_lawhttp://en.wikipedia.org/wiki/Newton%27s_laws_of_motion#Newton.27s_third_lawhttp://en.wikipedia.org/wiki/Newton%27s_laws_of_motion#Newton.27s_third_lawhttp://en.wikipedia.org/wiki/Newton%27s_laws_of_motion#Newton.27s_third_lawhttp://en.wikipedia.org/wiki/Wind_turbinehttp://en.wikipedia.org/wiki/Wind_turbinehttp://en.wikipedia.org/wiki/Wind_turbinehttp://en.wikipedia.org/wiki/Airfoilhttp://en.wikipedia.org/wiki/Airfoilhttp://en.wikipedia.org/wiki/Airfoilhttp://en.wikipedia.org/wiki/Lift_(force)http://en.wikipedia.org/wiki/Lift_(force)http://en.wikipedia.org/wiki/Lift_(force)http://en.wikipedia.org/wiki/Banki_turbinehttp://en.wikipedia.org/wiki/Banki_turbinehttp://en.wikipedia.org/wiki/Banki_turbinehttp://en.wikipedia.org/wiki/Flow_conditioninghttp://en.wikipedia.org/wiki/Flow_conditioninghttp://en.wikipedia.org/wiki/Flow_conditioninghttp://en.wikipedia.org/wiki/Classical_mechanicshttp://en.wikipedia.org/wiki/Classical_mechanicshttp://en.wikipedia.org/wiki/Classical_mechanicshttp://en.wikipedia.org/wiki/Classical_mechanicshttp://en.wikipedia.org/wiki/Flow_conditioninghttp://en.wikipedia.org/wiki/Banki_turbinehttp://en.wikipedia.org/wiki/Lift_(force)http://en.wikipedia.org/wiki/Airfoilhttp://en.wikipedia.org/wiki/Wind_turbinehttp://en.wikipedia.org/wiki/Newton%27s_laws_of_motion#Newton.27s_third_lawhttp://en.wikipedia.org/wiki/Newton%27s_laws_of_motion#Newton.27s_third_lawhttp://en.wikipedia.org/wiki/Steam_turbinehttp://en.wikipedia.org/wiki/Francis_turbinehttp://en.wikipedia.org/wiki/Francis_turbine8/22/2019 Lanco Amarkantak Power Ltd Korba Mechanical Vocational Training Report 1-Haxxo24 I~I
16/24
Velocity triangles can be used to calculate the basic performance of a turbine stage. Gas exits
the stationary turbine nozzle guide vanes at absolute velocity Va1. The rotor rotates at
velocity U. Relative to the rotor, the velocity of the gas as it impinges on the rotor entrance
is Vr1. The gas is turned by the rotor and exits, relative to the rotor, at velocity Vr2. However, in
absolute terms the rotor exit velocity is Va2. The velocity triangles are constructed using these
various velocity vectors. Velocity triangles can be constructed at any section through the
blading (for example: hub , tip, midsection and so on) but are usually shown at the mean stage
radius. Mean performance for the stage can be calculated from the velocity triangles, at this
radius, using the Euler equation:
Hence:
where:
specific enthalpy drop across stage
turbine entry total (or stagnation) temperature
turbine rotor peripheral velocity
change in whirl velocity
The turbine pressure ratio is a function of and the
turbine efficiency.
Modern turbine design carries the calculations
further.Computational fluid dynamicsdispenses with many of
the simplifying assumptions used to derive classical formulas
and computer software facilitates optimization. These tools
have led to steady improvements in turbine design over the
last forty years.
http://en.wikipedia.org/wiki/Computational_fluid_dynamicshttp://en.wikipedia.org/wiki/Computational_fluid_dynamicshttp://en.wikipedia.org/wiki/Computational_fluid_dynamicshttp://en.wikipedia.org/wiki/Computational_fluid_dynamics8/22/2019 Lanco Amarkantak Power Ltd Korba Mechanical Vocational Training Report 1-Haxxo24 I~I
17/24
Condenser
Condenser (heat transfer), a device or unit used to condense vapor into liquid. More specific articles
on some types include:
Air coilused in HVAC refrigeration systems
Condenser (laboratory), a range of laboratory glassware used to remove heat from fluids
Steam locomotive condensing apparatus
Surface condenser, a heat exchanger installed in steam-electric power stations to condense
turbine exhaust steam into water
Condenser (optics), in classical optics gathers visible light and directs it onto a projection lens
Condenser (microscope), a group of lenses mounted below the stage of an optical microscope to
concentrate light
Capacitor, formerly called a condenser, an electrical device that can store energy
Condenser microphone, a device that converts sound waves into an electrical signal
Steam locomotive condensing apparatus, a condenser fitted to steam locomotives for use in
tunnels and to increase range
Synchronous condenser, a rotating machine similar to a motor, used to control AC power flow in
electric power transmission
Electric generatorInelectricity generation, an electric generatoris a device that convertsmechanical energytoelectrical
energy. A generator forceselectronsin the windings to flow through the externalelectrical circuit. It is
somewhat analogous to a water pump, which creates a flow of water but does not create the water inside.
Thesource of mechanical energymay be a reciprocating or turbinesteam engine, water falling through
aturbine or waterwheel, aninternal combustion engine, awind turbine, a handcrank,compressed airor
any other source of mechanical energy.
http://en.wikipedia.org/wiki/Condenser_(heat_transfer)http://en.wikipedia.org/wiki/Condenser_(heat_transfer)http://en.wikipedia.org/wiki/Heat_exchanger#HVAC_air_coilshttp://en.wikipedia.org/wiki/Heat_exchanger#HVAC_air_coilshttp://en.wikipedia.org/wiki/Condenser_(laboratory)http://en.wikipedia.org/wiki/Condenser_(laboratory)http://en.wikipedia.org/wiki/Steam_locomotive_condensing_apparatushttp://en.wikipedia.org/wiki/Steam_locomotive_condensing_apparatushttp://en.wikipedia.org/wiki/Surface_condenserhttp://en.wikipedia.org/wiki/Surface_condenserhttp://en.wikipedia.org/wiki/Condenser_(optics)http://en.wikipedia.org/wiki/Condenser_(optics)http://en.wikipedia.org/wiki/Condenser_(microscope)http://en.wikipedia.org/wiki/Condenser_(microscope)http://en.wikipedia.org/wiki/Capacitorhttp://en.wikipedia.org/wiki/Capacitorhttp://en.wikipedia.org/wiki/Condenser_microphonehttp://en.wikipedia.org/wiki/Condenser_microphonehttp://en.wikipedia.org/wiki/Steam_locomotive_condensing_apparatushttp://en.wikipedia.org/wiki/Steam_locomotive_condensing_apparatushttp://en.wikipedia.org/wiki/Synchronous_condenserhttp://en.wikipedia.org/wiki/Synchronous_condenserhttp://en.wikipedia.org/wiki/Electricity_generationhttp://en.wikipedia.org/wiki/Electricity_generationhttp://en.wikipedia.org/wiki/Electricity_generationhttp://en.wikipedia.org/wiki/Mechanical_energyhttp://en.wikipedia.org/wiki/Mechanical_energyhttp://en.wikipedia.org/wiki/Mechanical_energyhttp://en.wikipedia.org/wiki/Electrical_energyhttp://en.wikipedia.org/wiki/Electrical_energyhttp://en.wikipedia.org/wiki/Electrical_energyhttp://en.wikipedia.org/wiki/Electrical_energyhttp://en.wikipedia.org/wiki/Electronshttp://en.wikipedia.org/wiki/Electronshttp://en.wikipedia.org/wiki/Electronshttp://en.wikipedia.org/wiki/Electrical_circuithttp://en.wikipedia.org/wiki/Electrical_circuithttp://en.wikipedia.org/wiki/Electrical_circuithttp://en.wiktionary.org/wiki/prime_moverhttp://en.wiktionary.org/wiki/prime_moverhttp://en.wiktionary.org/wiki/prime_moverhttp://en.wikipedia.org/wiki/Steam_enginehttp://en.wikipedia.org/wiki/Steam_enginehttp://en.wikipedia.org/wiki/Steam_enginehttp://en.wikipedia.org/wiki/Hydropowerhttp://en.wikipedia.org/wiki/Hydropowerhttp://en.wikipedia.org/wiki/Hydropowerhttp://en.wikipedia.org/wiki/Internal_combustion_enginehttp://en.wikipedia.org/wiki/Internal_combustion_enginehttp://en.wikipedia.org/wiki/Wind_turbinehttp://en.wikipedia.org/wiki/Wind_turbinehttp://en.wikipedia.org/wiki/Wind_turbinehttp://en.wikipedia.org/wiki/Crank_(mechanism)http://en.wikipedia.org/wiki/Crank_(mechanism)http://en.wikipedia.org/wiki/Compressed_airhttp://en.wikipedia.org/wiki/Compressed_airhttp://en.wikipedia.org/wiki/Compressed_airhttp://en.wikipedia.org/wiki/Compressed_airhttp://en.wikipedia.org/wiki/Crank_(mechanism)http://en.wikipedia.org/wiki/Wind_turbinehttp://en.wikipedia.org/wiki/Internal_combustion_enginehttp://en.wikipedia.org/wiki/Hydropowerhttp://en.wikipedia.org/wiki/Steam_enginehttp://en.wiktionary.org/wiki/prime_moverhttp://en.wikipedia.org/wiki/Electrical_circuithttp://en.wikipedia.org/wiki/Electronshttp://en.wikipedia.org/wiki/Electrical_energyhttp://en.wikipedia.org/wiki/Electrical_energyhttp://en.wikipedia.org/wiki/Mechanical_energyhttp://en.wikipedia.org/wiki/Electricity_generationhttp://en.wikipedia.org/wiki/Synchronous_condenserhttp://en.wikipedia.org/wiki/Steam_locomotive_condensing_apparatushttp://en.wikipedia.org/wiki/Condenser_microphonehttp://en.wikipedia.org/wiki/Capacitorhttp://en.wikipedia.org/wiki/Condenser_(microscope)http://en.wikipedia.org/wiki/Condenser_(optics)http://en.wikipedia.org/wiki/Surface_condenserhttp://en.wikipedia.org/wiki/Steam_locomotive_condensing_apparatushttp://en.wikipedia.org/wiki/Condenser_(laboratory)http://en.wikipedia.org/wiki/Heat_exchanger#HVAC_air_coilshttp://en.wikipedia.org/wiki/Condenser_(heat_transfer)8/22/2019 Lanco Amarkantak Power Ltd Korba Mechanical Vocational Training Report 1-Haxxo24 I~I
18/24
Early 20th centuryalternatormade inBudapest,Hungary, in the power generating hall of ahydroelectricstation
EarlyGanzGenerator inZwevegem,West Flanders,Belgium
The reverse conversion of electrical energy into mechanical energy is done by anelectric motor, and
motors and generators have many similarities. In fact many motors can be mechanically driven to
generate electricity, and very frequently make acceptable generators.
http://en.wikipedia.org/wiki/Alternatorhttp://en.wikipedia.org/wiki/Alternatorhttp://en.wikipedia.org/wiki/Alternatorhttp://en.wikipedia.org/wiki/Budapesthttp://en.wikipedia.org/wiki/Budapesthttp://en.wikipedia.org/wiki/Hungaryhttp://en.wikipedia.org/wiki/Hungaryhttp://en.wikipedia.org/wiki/Hungaryhttp://en.wikipedia.org/wiki/Hydroelectrichttp://en.wikipedia.org/wiki/Hydroelectrichttp://en.wikipedia.org/wiki/Hydroelectrichttp://en.wikipedia.org/wiki/Ganzhttp://en.wikipedia.org/wiki/Ganzhttp://en.wikipedia.org/wiki/Ganzhttp://en.wikipedia.org/wiki/Zwevegemhttp://en.wikipedia.org/wiki/Zwevegemhttp://en.wikipedia.org/wiki/West_Flandershttp://en.wikipedia.org/wiki/West_Flandershttp://en.wikipedia.org/wiki/West_Flandershttp://en.wikipedia.org/wiki/Belgiumhttp://en.wikipedia.org/wiki/Belgiumhttp://en.wikipedia.org/wiki/Belgiumhttp://en.wikipedia.org/wiki/Electric_motorhttp://en.wikipedia.org/wiki/Electric_motorhttp://en.wikipedia.org/wiki/Electric_motorhttp://en.wikipedia.org/wiki/File:Generator-20071117.jpghttp://en.wikipedia.org/wiki/File:Generator-20071117.jpghttp://en.wikipedia.org/wiki/File:Gorskii_04414u.jpghttp://en.wikipedia.org/wiki/File:Gorskii_04414u.jpghttp://en.wikipedia.org/wiki/File:Generator-20071117.jpghttp://en.wikipedia.org/wiki/File:Generator-20071117.jpghttp://en.wikipedia.org/wiki/File:Gorskii_04414u.jpghttp://en.wikipedia.org/wiki/File:Gorskii_04414u.jpghttp://en.wikipedia.org/wiki/File:Generator-20071117.jpghttp://en.wikipedia.org/wiki/File:Generator-20071117.jpghttp://en.wikipedia.org/wiki/File:Gorskii_04414u.jpghttp://en.wikipedia.org/wiki/File:Gorskii_04414u.jpghttp://en.wikipedia.org/wiki/File:Generator-20071117.jpghttp://en.wikipedia.org/wiki/File:Generator-20071117.jpghttp://en.wikipedia.org/wiki/File:Gorskii_04414u.jpghttp://en.wikipedia.org/wiki/File:Gorskii_04414u.jpghttp://en.wikipedia.org/wiki/Electric_motorhttp://en.wikipedia.org/wiki/Belgiumhttp://en.wikipedia.org/wiki/West_Flandershttp://en.wikipedia.org/wiki/Zwevegemhttp://en.wikipedia.org/wiki/Ganzhttp://en.wikipedia.org/wiki/Hydroelectrichttp://en.wikipedia.org/wiki/Hungaryhttp://en.wikipedia.org/wiki/Budapesthttp://en.wikipedia.org/wiki/Alternator8/22/2019 Lanco Amarkantak Power Ltd Korba Mechanical Vocational Training Report 1-Haxxo24 I~I
19/24
What We Learn In Our Vocational Training At Lanco
During our vocational Training at Lanco (EPC). We are with Turbine Team & Here
we got opportunity to learn following things:
1. Setup of Turbine Deck
2. Strength Checking By UT
3. Setup of Condenser Foundation4. Centre Line Marking
5. Blue Matching of Foundation Plates
1.SETUP OF TURBINE DECK
Turbine deck consists of three floors
a)Ground Floorb)First Floor or Massinne Floor
c)Second Floor or Operating Floor
2.Strength checking by UT
It is done to check the strength of the foundation.
It can show the air bubbles between the concrete
through waves. It is measure done to prevent thefoundation from being collapsed.
8/22/2019 Lanco Amarkantak Power Ltd Korba Mechanical Vocational Training Report 1-Haxxo24 I~I
20/24
PRINCIPAL OF POWER PLANT
8/22/2019 Lanco Amarkantak Power Ltd Korba Mechanical Vocational Training Report 1-Haxxo24 I~I
21/24
Rankine cycle
The Rankine cycle is a cycle that converts heat into work. The heat is supplied externally to a closedloop, which usually uses water. This cycle generates about 80% of all electric power used throughout the
world, including virtually allsolar thermal,biomass,coalandnuclearpower plants. It is namedafterWilliam John Macquorn Rankine, a Scottishpolymath. The Rankine cycle is the fundamental
thermodynamic underpinning of thesteam engine
Description
Physical layout of the four main devices used in the Rankine cycle
A Rankine cycle describes a model of steam-operatedheat enginemost commonly found inpower
generation plants. Common heat sources for power plants using the Rankine cycle are the combustion
ofcoal,natural gasandoil, andnuclear fission.
The Rankine cycle is sometimes referred to as a practicalCarnot cyclebecause, when an efficient turbine
is used, theTS diagrambegins to resemble the Carnot cycle. The main difference is that heat addition (in
the boiler) and rejection (in the condenser) areisobaricin the Rankine cycle andisothermalin the
theoretical Carnot cycle. A pump is used to pressurize the working fluid received from the condenser as a
liquid instead of as a gas. All of the energy in pumping the working fluid through the complete cycle is
lost, as is all of the energy of vaporization of the working fluid in the boiler. This energy is lost to the cycle
in that no condensation takes place in the turbine; all of the vaporization energy is rejected from the cycle
through the condenser. But pumping the working fluid through the cycle as a liquid requires a very small
fraction of the energy needed to transport it as compared to compressing the working fluid as a gas in a
compressor (as in theCarnot cycle).
http://en.wikipedia.org/wiki/Solar_thermalhttp://en.wikipedia.org/wiki/Solar_thermalhttp://en.wikipedia.org/wiki/Solar_thermalhttp://en.wikipedia.org/wiki/Biomasshttp://en.wikipedia.org/wiki/Biomasshttp://en.wikipedia.org/wiki/Biomasshttp://en.wikipedia.org/wiki/Coal_powerhttp://en.wikipedia.org/wiki/Coal_powerhttp://en.wikipedia.org/wiki/Coal_powerhttp://en.wikipedia.org/wiki/Nuclear_powerhttp://en.wikipedia.org/wiki/Nuclear_powerhttp://en.wikipedia.org/wiki/Power_planthttp://en.wikipedia.org/wiki/Power_planthttp://en.wikipedia.org/wiki/Power_planthttp://en.wikipedia.org/wiki/William_John_Macquorn_Rankinehttp://en.wikipedia.org/wiki/William_John_Macquorn_Rankinehttp://en.wikipedia.org/wiki/William_John_Macquorn_Rankinehttp://en.wikipedia.org/wiki/Polymathhttp://en.wikipedia.org/wiki/Polymathhttp://en.wikipedia.org/wiki/Polymathhttp://en.wikipedia.org/wiki/Steam_enginehttp://en.wikipedia.org/wiki/Steam_enginehttp://en.wikipedia.org/wiki/Steam_enginehttp://en.wikipedia.org/wiki/Heat_enginehttp://en.wikipedia.org/wiki/Heat_enginehttp://en.wikipedia.org/wiki/Heat_enginehttp://en.wikipedia.org/wiki/Power_stationhttp://en.wikipedia.org/wiki/Power_stationhttp://en.wikipedia.org/wiki/Power_stationhttp://en.wikipedia.org/wiki/Power_stationhttp://en.wikipedia.org/wiki/Coalhttp://en.wikipedia.org/wiki/Coalhttp://en.wikipedia.org/wiki/Coalhttp://en.wikipedia.org/wiki/Natural_gashttp://en.wikipedia.org/wiki/Natural_gashttp://en.wikipedia.org/wiki/Natural_gashttp://en.wikipedia.org/wiki/Fuel_oilhttp://en.wikipedia.org/wiki/Fuel_oilhttp://en.wikipedia.org/wiki/Fuel_oilhttp://en.wikipedia.org/wiki/Nuclear_powerhttp://en.wikipedia.org/wiki/Nuclear_powerhttp://en.wikipedia.org/wiki/Nuclear_powerhttp://en.wikipedia.org/wiki/Carnot_cyclehttp://en.wikipedia.org/wiki/Carnot_cyclehttp://en.wikipedia.org/wiki/TS_diagramhttp://en.wikipedia.org/wiki/TS_diagramhttp://en.wikipedia.org/wiki/TS_diagramhttp://en.wikipedia.org/wiki/Isobaric_processhttp://en.wikipedia.org/wiki/Isobaric_processhttp://en.wikipedia.org/wiki/Isobaric_processhttp://en.wikipedia.org/wiki/Isothermal_processhttp://en.wikipedia.org/wiki/Isothermal_processhttp://en.wikipedia.org/wiki/Isothermal_processhttp://en.wikipedia.org/wiki/Carnot_cyclehttp://en.wikipedia.org/wiki/Carnot_cyclehttp://en.wikipedia.org/wiki/Carnot_cyclehttp://en.wikipedia.org/wiki/File:Rankine_cycle_layout.pnghttp://en.wikipedia.org/wiki/File:Rankine_cycle_layout.pnghttp://en.wikipedia.org/wiki/File:Rankine_cycle_layout.pnghttp://en.wikipedia.org/wiki/File:Rankine_cycle_layout.pnghttp://en.wikipedia.org/wiki/Carnot_cyclehttp://en.wikipedia.org/wiki/Isothermal_processhttp://en.wikipedia.org/wiki/Isobaric_processhttp://en.wikipedia.org/wiki/TS_diagramhttp://en.wikipedia.org/wiki/Carnot_cyclehttp://en.wikipedia.org/wiki/Nuclear_powerhttp://en.wikipedia.org/wiki/Fuel_oilhttp://en.wikipedia.org/wiki/Natural_gashttp://en.wikipedia.org/wiki/Coalhttp://en.wikipedia.org/wiki/Power_stationhttp://en.wikipedia.org/wiki/Power_stationhttp://en.wikipedia.org/wiki/Heat_enginehttp://en.wikipedia.org/wiki/Steam_enginehttp://en.wikipedia.org/wiki/Polymathhttp://en.wikipedia.org/wiki/William_John_Macquorn_Rankinehttp://en.wikipedia.org/wiki/Power_planthttp://en.wikipedia.org/wiki/Nuclear_powerhttp://en.wikipedia.org/wiki/Coal_powerhttp://en.wikipedia.org/wiki/Biomasshttp://en.wikipedia.org/wiki/Solar_thermal8/22/2019 Lanco Amarkantak Power Ltd Korba Mechanical Vocational Training Report 1-Haxxo24 I~I
22/24
The efficiency of a Rankine cycle is usually limited by the working fluid. Without the pressure
reachingsuper criticallevels for the working fluid, the temperature range the cycle can operate over is
quite small: turbine entry temperatures are typically 565C (thecreeplimit of stainless steel) and
condenser temperatures are around 30C. This gives a theoreticalCarnot efficiencyof about 63%
compared with an actual efficiency of 42% for a modern coal-fired power station. This low turbine entry
temperature (compared with agas turbine) is why the Rankine cycle is often used as a bottoming cycle
incombined-cycle gas turbinepower stations.
The working fluid in a Rankine cycle follows a closed loop and is reused constantly. The watervaporwith
entrained droplets often seen billowing from power stations is generated by the cooling systems (not from
the closed-loop Rankine power cycle) and represents the waste energy heat (pumping and vaporization)
that could not be converted to useful work in the turbine. Note thatcooling towersoperate using the
latentheat of vaporizationof the cooling fluid. The white billowing clouds that form in cooling tower
operation are the result of water droplets that are entrained in the cooling tower airflow; they are not, ascommonly thought, steam. While many substances could be used in the Rankine cycle, water is usually
the fluid of choice due to its favorable properties, such as nontoxic and unreactive chemistry, abundance,
and low cost, as well as itsthermodynamic properties.
One of the principal advantages the Rankine cycle holds over others is that during the compression stage
relatively little work is required to drive the pump, the working fluid being in its liquid phase at this point.
By condensing the fluid, the work required by the pump consumes only 1% to 3% of the turbine power
and contributes to a much higher efficiency for a real cycle. The benefit of this is lost somewhat due to the
lower heat addition temperature.Gas turbines, for instance, have turbine entry temperatures approaching1500C. Nonetheless, the efficiencies of actual large steam cycles and large modern gas turbines are
fairly well matched.
[edit]The four processes in the Rankine cycle
http://en.wikipedia.org/wiki/Critical_point_(thermodynamics)http://en.wikipedia.org/wiki/Critical_point_(thermodynamics)http://en.wikipedia.org/wiki/Critical_point_(thermodynamics)http://en.wikipedia.org/wiki/Creep_(deformation)http://en.wikipedia.org/wiki/Creep_(deformation)http://en.wikipedia.org/wiki/Creep_(deformation)http://en.wikipedia.org/wiki/Carnot_efficiencyhttp://en.wikipedia.org/wiki/Carnot_efficiencyhttp://en.wikipedia.org/wiki/Carnot_efficiencyhttp://en.wikipedia.org/wiki/Gas_turbinehttp://en.wikipedia.org/wiki/Gas_turbinehttp://en.wikipedia.org/wiki/Gas_turbinehttp://en.wikipedia.org/wiki/Combined_cyclehttp://en.wikipedia.org/wiki/Combined_cyclehttp://en.wikipedia.org/wiki/Combined_cyclehttp://en.wikipedia.org/wiki/Vaporhttp://en.wikipedia.org/wiki/Vaporhttp://en.wikipedia.org/wiki/Vaporhttp://en.wikipedia.org/wiki/Cooling_towerhttp://en.wikipedia.org/wiki/Cooling_towerhttp://en.wikipedia.org/wiki/Cooling_towerhttp://en.wikipedia.org/wiki/Heat_of_vaporizationhttp://en.wikipedia.org/wiki/Heat_of_vaporizationhttp://en.wikipedia.org/wiki/Heat_of_vaporizationhttp://en.wikipedia.org/wiki/Properties_of_water#Heat_capacity_and_heats_of_vaporization_and_fusionhttp://en.wikipedia.org/wiki/Properties_of_water#Heat_capacity_and_heats_of_vaporization_and_fusionhttp://en.wikipedia.org/wiki/Properties_of_water#Heat_capacity_and_heats_of_vaporization_and_fusionhttp://en.wikipedia.org/wiki/Gas_turbinehttp://en.wikipedia.org/wiki/Gas_turbinehttp://en.wikipedia.org/wiki/Gas_turbinehttp://en.wikipedia.org/w/index.php?title=Rankine_cycle&action=edit§ion=2http://en.wikipedia.org/w/index.php?title=Rankine_cycle&action=edit§ion=2http://en.wikipedia.org/w/index.php?title=Rankine_cycle&action=edit§ion=2http://en.wikipedia.org/w/index.php?title=Rankine_cycle&action=edit§ion=2http://en.wikipedia.org/wiki/Gas_turbinehttp://en.wikipedia.org/wiki/Properties_of_water#Heat_capacity_and_heats_of_vaporization_and_fusionhttp://en.wikipedia.org/wiki/Heat_of_vaporizationhttp://en.wikipedia.org/wiki/Cooling_towerhttp://en.wikipedia.org/wiki/Vaporhttp://en.wikipedia.org/wiki/Combined_cyclehttp://en.wikipedia.org/wiki/Gas_turbinehttp://en.wikipedia.org/wiki/Carnot_efficiencyhttp://en.wikipedia.org/wiki/Creep_(deformation)http://en.wikipedia.org/wiki/Critical_point_(thermodynamics)8/22/2019 Lanco Amarkantak Power Ltd Korba Mechanical Vocational Training Report 1-Haxxo24 I~I
23/24
Ts diagramof a typical Rankine cycle operating between pressures of 0.06bar and 50bar
There are four processes in the Rankine cycle. These states are identified by numbers (in brown) in the
diagram above.
Process 1-2: The working fluid is pumped from low to high pressure, as the fluid is a liquid at this
stage the pump requires little input energy.
Process 2-3: The high pressure liquid enters a boiler where it is heated at constant pressure by an
external heat source to become a dry saturated vapor. The input energy required can be easily
calculated usingmollier diagramorh-s chartorenthalpy-entropy chartalso known assteam tables.
Process 3-4: The dry saturated vapor expands through aturbine, generating power. This decreases
the temperature and pressure of the vapor, and some condensation may occur. The output in this
process can be easily calculated using theEnthalpy-entropy chartor the steam tables.
Process 4-1: The wet vapor then enters acondenserwhere it is condensed at a constant
temperature to become asaturated liquid.
http://en.wikipedia.org/wiki/Ts_diagramhttp://en.wikipedia.org/wiki/Ts_diagramhttp://en.wikipedia.org/wiki/Mollier_diagramhttp://en.wikipedia.org/wiki/Mollier_diagramhttp://en.wikipedia.org/wiki/H-s_charthttp://en.wikipedia.org/wiki/H-s_charthttp://en.wikipedia.org/wiki/H-s_charthttp://en.wikipedia.org/wiki/Enthalpy-entropy_charthttp://en.wikipedia.org/wiki/Enthalpy-entropy_charthttp://en.wikipedia.org/wiki/Enthalpy-entropy_charthttp://en.wikipedia.org/wiki/Steam_tablehttp://en.wikipedia.org/wiki/Steam_tablehttp://en.wikipedia.org/wiki/Steam_tablehttp://en.wikipedia.org/wiki/Turbinehttp://en.wikipedia.org/wiki/Turbinehttp://en.wikipedia.org/wiki/Turbinehttp://en.wikipedia.org/wiki/Enthalpy-entropy_charthttp://en.wikipedia.org/wiki/Enthalpy-entropy_charthttp://en.wikipedia.org/wiki/Enthalpy-entropy_charthttp://en.wikipedia.org/wiki/Surface_condenserhttp://en.wikipedia.org/wiki/Surface_condenserhttp://en.wikipedia.org/wiki/Surface_condenserhttp://en.wikipedia.org/wiki/Boiling_pointhttp://en.wikipedia.org/wiki/Boiling_pointhttp://en.wikipedia.org/wiki/Boiling_pointhttp://en.wikipedia.org/wiki/File:Rankine_cycle_Ts.pnghttp://en.wikipedia.org/wiki/File:Rankine_cycle_Ts.pnghttp://en.wikipedia.org/wiki/File:Rankine_cycle_Ts.pnghttp://en.wikipedia.org/wiki/File:Rankine_cycle_Ts.pnghttp://en.wikipedia.org/wiki/Boiling_pointhttp://en.wikipedia.org/wiki/Surface_condenserhttp://en.wikipedia.org/wiki/Enthalpy-entropy_charthttp://en.wikipedia.org/wiki/Turbinehttp://en.wikipedia.org/wiki/Steam_tablehttp://en.wikipedia.org/wiki/Enthalpy-entropy_charthttp://en.wikipedia.org/wiki/H-s_charthttp://en.wikipedia.org/wiki/Mollier_diagramhttp://en.wikipedia.org/wiki/Ts_diagram8/22/2019 Lanco Amarkantak Power Ltd Korba Mechanical Vocational Training Report 1-Haxxo24 I~I
24/24
In an ideal Rankine cycle the pump and turbine would beisentropic, i.e., the pump and turbine would
generate no entropy and hence maximize the net work output. Processes 1-2 and 3-4 would be
represented by vertical lines on theT-S diagramand more closely resemble that of the Carnot cycle. The
Rankine cycle shown here prevents the vapor ending up in the superheat region after the expansion in
the turbine,[1]which reduces the energy removed by the condensers.|~|
http://en.wikipedia.org/wiki/Isentropichttp://en.wikipedia.org/wiki/Isentropichttp://en.wikipedia.org/wiki/Isentropichttp://en.wikipedia.org/wiki/T-S_diagramhttp://en.wikipedia.org/wiki/T-S_diagramhttp://en.wikipedia.org/wiki/T-S_diagramhttp://en.wikipedia.org/wiki/Rankine_cycle#endnote_Van_Wyllen_ahttp://en.wikipedia.org/wiki/Rankine_cycle#endnote_Van_Wyllen_ahttp://en.wikipedia.org/wiki/Rankine_cycle#endnote_Van_Wyllen_ahttp://en.wikipedia.org/wiki/Rankine_cycle#endnote_Van_Wyllen_ahttp://en.wikipedia.org/wiki/T-S_diagramhttp://en.wikipedia.org/wiki/IsentropicRecommended