KPS testing and certifications V2€¦ · STATE LICENSED CONTRACTOR STATE CERTIFIED MANUFACTURER OF...

STATE LICENSED CONTRACTOR

STATE CERTIFIED MANUFACTURER OF MODULAR/COMPONENT STRUCTURES

This license is not required in all states (29 do not require state building contractor licenses).

AlabamaArizonaCaliforniaColoradoConnecticut

GeorgiaIowa KentuckyLouisianaMaryland

MassachusettsMinnesotaMissouriNew HampshireNew Jersey

North DakotaRhode IslandSouth Carolina TennesseeVirginiaWashington

CODE COMPLIANCE TESTING

The International Building Code required this testing be done by a nationally recognized third party testing agency.

Registered with the Texas Board of Professional Engineers to o�er and perform Engineering Services in the State of Texas

This testing is not acceptable if conducted by the manufacturer or the foam insulation supplierASTM D-2126 - Dimensional StabilityASTM D-2294 - AdhesionASTM D-2856 - Open Cell ContentASTM E-72 - Compressive Load, Transverse Load and Racking LoadASTM E-90 - Acoustic PerformanceASTM E-331 - Water penetration of exterior wallsASTM E-661 - Concentrated and Impact Loads

ASTM C-272 - Water absorptionASTM C-273 - Shear StrengthASTM C-393 - Flexural StrengthASTM C-518 - Thermal TransmissionASTM D-635 - Horizontal BurningASTM D-1621 - Compressive PropertiesASTM D-1622 - DensityASTM D-1623 - Tensile Strength

AlaskaCaliforniaDelawareFloridaGeorgiaLouisiana

MississippiNevadaNew MexicoNorth DakotaOregonSouth Carolina

TennesseeUtahVirginia

01-19

WashingtonWest Virginia

FLAMMABILITY

ASTM E-84, ANSI 2.5, NFPA 255, UBC 42-1 - Surface Burning Characteristics-CoreASTM D-1929 - Ignition Properties Required by Chapter 26 of the IBC for plastic insulation in sprinklered buildingsASTM E-108 - Fire test of roof panelsFM 4880 - Fire Rating of Insulated Wall & Ceiling Panels - RoomUL 723 UL1715 - Fire Rating of Insulated Wall & Ceiling Panels - Room CAN/ULC S-102 - Surface Burning Characteristics – Core and Finished Panel

- Surface Burning Characteristics – Core and Finished panels speci�ed by Food Consulatants

CAN/ULC S-127 - Corner Wall FlammabilityCAN/ULC S-138 - Fire Growth and Damageability – Room Required to sell product in CanadaNFPA 286 - Fire Contribution – allows panels without sprinklers and without Thermal Barriers

TESTING AND CERTIFICATIONS

ENGINEERING SERVICES

This certi�cation is required to obtain and apply State Lables to preassembled Environmental Enclosures prior toshipping into the state

www.kpsglobal.com

01-19

LISTING AND LABELS

National Sanitation Foundation (NSF)

US Department of Agriculture (USDA) Acceptance Required for meat and poultry processing facilitiesCanadian Food Inspection Agency (CFIA) Acceptance

Required for meat and poultry processing facilities in Canada

ETL/UL 471 - UL Standard for Safety-Refrigerators/FreezersCSA C22.2 - CAN/CSA Refrigeration Equipment Required for all prewired electrical in Canada

Miami-Dade County - Florida Building Code – Hurricane Winds

Required for outdoor installation in FloridaCity of Los Angeles - Municipal Building Code – Seismic Forces

Required for indoor & outdoor installation in Los AngelesCity of Houston - Houston Building Code- Fire and Structural

Required for indoor & outdoor installation in HoustonCity of New York - Material & Equipment Acceptance – Toxicity

Required for indoor & outdoor installation in New York CityState of California - Licensed Thermal Insulation Manufacturer

Required to sell product in CaliforniaState of Oregon - Prefabricated Structures

Required to sell product in OregonState of Wisconsin - Material Approval

Required to sell product in Wisconsin

SANITATION

ELECTRICAL

APPROVALS

Standard 7 Required by many Heath Departments and speci�ed by Food Consultants

www.kpsglobal.com