Keysight X-Series Signal Analyzer

This manual provides documentation for the following X-Series Analyzers:PXA Signal Analyzer N9030AMXA Signal Analyzer N9020AEXA Signal Analyzer N9010ACXA Signal Analyzer N9000A

N6149AiDEN/WiDEN/MotoTalk AnalyzerMeasurementApplication Users &ProgrammersReference

Keysight X-Series Signal Analyzer

Notices Keysight Technologies, Inc.2008-2014No part of this manual may bereproduced in any form or by anymeans (including electronicstorage and retrieval ortranslation into a foreignlanguage) without prioragreement and written consentfrom Keysight Technologies, Inc.as governed by United States andinternational copyright laws.

AcknowledgmentsAdobe Acrobat and Readerare U.S. registered trademarks ofAdobe Systems Incorporated.

Manual Part NumberN6149-90001

EditionAugust 2014Printed in USAKeysight Technologies, Inc.1400 Fountaingrove ParkwaySanta Rosa, CA 95403

WarrantyThe material contained in thisdocument is provided as is, andis subject to being changed,without notice, in future editions.Further, to the maximum extentpermitted by applicable law,Keysight disclaims all warranties,either express or implied, withregard to this manual and anyinformation contained herein,including but not limited to theimplied warranties ofmerchantability and fitness for aparticular purpose. Keysight shallnot be liable for errors or forincidental or consequential

damages in connection with thefurnishing, use, or performance ofthis document or of anyinformation contained herein.Should Keysight and the userhave a separate writtenagreement with warranty termscovering the material in thisdocument that conflict with theseterms, the warranty terms in theseparate agreement shall control.

Technology LicensesThe hardware and/or softwaredescribed in this document arefurnished under a license and maybe used or copied only inaccordance with the terms of suchlicense.

Restricted RightsLegendIf software is for use in theperformance of a U.S.Government prime contract orsubcontract, Software is deliveredand licensed as Commercialcomputer software as defined inDFAR 252.227-7014 (June 1995),or as a commercial item asdefined in FAR 2.101(a) or asRestricted computer softwareas defined in FAR 52.227-19 (June1987) or any equivalent agencyregulation or contract clause.Use, duplication or disclosure ofSoftware is subject to KeysightTechnologies standardcommercial license terms, andnon-DOD Departments andAgencies of the U.S. Governmentwill receive no greater thanRestricted Rights as defined inFAR 52.227-19(c)(1-2) (June1987). U.S. Government users will

receive no greater than LimitedRights as defined in FAR 52.227-14 (June 1987) or DFAR 252.227-7015 (b)(2) (November 1995), asapplicable in any technical data.

Safety Notices

A CAUTION notice denotes a hazard. It callsattention to an operating procedure, practice,or the like that, if not correctly performed oradhered to, could result in damage to theproduct or loss of important data. Do notproceed beyond a CAUTION notice until theindicated conditions are fully understood andmet.

A WARNING notice denotes a hazard. It callsattention to an operating procedure,practice, or the like that, if not correctlyperformed or adhered to, could result inpersonal injury or death. Do not proceedbeyond a WARNING notice until the indicatedconditions are fully understood and met.

ii iDEN/WiDEN/MotoTalk Analyzer Measurement Application Reference

Table of Contents

Table of Contents

N6149A iDEN/WiDEN/MotoTalk Analyzer Measurement Application Users & ProgrammersReference i

Table of Contents iii

1 About the Analyzer 53Installing Application Software 54

Viewing a License Key 54Obtaining and Installing a License Key 54Updating Measurement Application Software 54

X-Series Options and Accessories 56Front-Panel Features 57Display Annotations 58Rear-Panel Features 59Window Control Keys 60

Multi-Window 60Zoom 60Next Window 61Full Screen 62Display Enable (Remote Command Only) 62

Mouse and Keyboard Control 64Right-Click 64PC Keyboard 66

Instrument Security & Memory Volatility 69

2 About the iDEN/WiDEN/MotoTalk Analyzer Measurement Application 71What Does the iDEN/WiDEN/MotoTalk Analyzer Measurement Application Do? 72

3 Programming the Analyzer 73What Programming Information is Available? 74List of SCPI Commands 75STATus Subsystem 94

Detailed Description 96What Are Status Registers 97What Are Status Register SCPI Commands 97How to Use the Status Registers 98Using a Status Register 99Using the Service Request (SRQ) Method 100

Generating a Service Request 100Status Register System 101The Status Byte Register 102Standard Event Status Register 104Operation and Questionable Status Registers 106

Operation Status Register 106

iDEN/WiDEN/MotoTalk Analyzer Measurement Application Reference iii

Table of Contents

Questionable Status Register 106STATus Subsystem Command Descriptions 107

Operation Register 107Operation Condition Query 107Operation Enable 108Operation Event Query 108Operation Negative Transition 108Operation Positive Transition 109

Preset the Status Byte 109Questionable Register 110

Questionable Condition 110Questionable Enable 110Questionable Event Query 111Questionable Negative Transition 111Questionable Positive Transition 111

Questionable Calibration Register 112Questionable Calibration Condition 112Questionable Calibration Enable 112Questionable Calibration Event Query 113Questionable Calibration Negative Transition 113Questionable Calibration Positive Transition 114

Questionable Calibration Skipped Register 114Questionable Calibration Skipped Condition 114Questionable Calibration Skipped Enable 115Questionable Calibration Skipped Event Query 115Questionable Calibration Skipped Negative Transition 116Questionable Calibration Skipped Positive Transition 116

Questionable Calibration Extended Failure Register 116Questionable Calibration Extended Failure Condition 117Questionable Calibration Extended Failure Enable 117Questionable Calibration Extended Failure Event Query 117Questionable Calibration Extended Failure Negative Transition 118Questionable Calibration Extended Failure Positive Transition 118

Questionable Calibration Extended Needed Register 119Questionable Calibration Extended Needed Condition 119Questionable Calibration Extended Needed Enable 119Questionable Calibration Extended Needed Event Query 120Questionable Calibration Extended Needed Negative Transition 120Questionable Calibration Extended Needed Positive Transition 121

Questionable Frequency Register 121Questionable Frequency Condition 121Questionable Frequency Enable 122Questionable Frequency Event Query 122

iv iDEN/WiDEN/MotoTalk Analyzer Measurement Application Reference

Table of Contents

Questionable Frequency Negative Transition 122Questionable Frequency Positive Transition 123

Questionable Integrity Register 123Questionable Integrity Condition 123Questionable Integrity Enable 124Questionable Integrity Event Query 124Questionable Integrity Negative Transition 125Questionable Integrity Positive Transition 125

Questionable Integrity Signal Register 125Questionable Integrity Signal Condition 126Questionable Integrity Signal Enable 126Questionable Integrity Signal Event Query 127Questionable Integrity Signal Negative Transition 127Questionable Integrity Signal Positive Transition 127

Questionable Integrity Uncalibrated Register 128Questionable Integrity Uncalibrated Condition 128Questionable Integrity Uncalibrated Enable 128Questionable Integrity Uncalibrated Event Query 129Questionable Integrity Uncalibrated Negative Transition 129Questionable Integrity Uncalibrated Positive Transition 130

Questionable Power Register 130Questionable Power Condition 130Questionable Power Enable 131Questionable Power Event Query 131Questionable Power Negative Transition 132Questionable Power Positive Transition 132

Questionable Temperature Register 132Questionable Temperature Condition 133Questionable Temperature Enable 133Questionable Temperature Event Query 133Questionable Temperature Negative Transition 134Questionable Temperature Positive Transition 134

IEEE 488.2 Common Commands 136All 136Clear Status 138Standard Event Status Enable 138Standard Event Status Register Query 139Identification Query 139Operation Complete 140Query Instrument Options 141Recall Instrument State 141*RST (Remote Command Only) 142Save Instrument State 142

iDEN/WiDEN/MotoTalk Analyzer Measurement Application Reference v

Table of Contents

Service Request Enable 142Status Byte Query 143Trigger 143Self Test Query 143Wait-to-Continue 144

4 Input/Output Functions 145Input/Output 146

Input/Output variables - Preset behavior 147RF Input 148

Input Z Correction 148RF Coupling 149

I/Q 150Baseband I/Q (Option BBA) 150Baseband I/Q Remote Language Compatibility 152I/Q Path 153

I+jQ 154I Only 154Q Only 155

I Setup 155I Differential Input 155I Input Z 156I Skew 157I Probe 157Combined Differential/Input Z (Remote Command Only) 159

Q Setup 160Q Same as I 160Q Differential Input 161Q Input Z 162Q Skew 162Q Probe 163

Reference Z 165I/Q Probe Setup 165

Attenuation 166Offset 167Coupling 167Calibrate 168Clear Calibration 169

RF Calibrator 16950MHz 1704.8GHz 170Off 171

External Gain 171Ext Preamp 171

vi iDEN/WiDEN/MotoTalk Analyzer Measurement Application Reference

Table of Contents

More Information 172MS 173BTS 174I Ext Gain 175Q Ext Gain 175

Restore Input/Output Defaults 176Freq Ref In 176

Sense 178Internal 178External 179Ext Ref Freq 179External Reference Lock BW 180External Ref Coupling 181

I/Q Guided Calibration 182I/Q Isolation Calibration 183

Next 183Exit 183

I/Q Isolation Calibration Time (Remote Command Only) 183I/Q Cable Calibrate 184

I Port 184I-bar Port 185Q Port 186Q-bar Port 187I/Q Cable Calibration Time (Remote Command Only) 188

I/Q Probe Calibration 188I Port 189I-bar Port 190Q Port 192Q-bar Port 193Show Adapter Screen 194I/Q Probe Calibration Time (Remote Command Only) 194

Exit Confirmation 194

5 Mode Functions 195Mode 196

More Information 197Spectrum Analyzer 198EMI Receiver 199IQ Analyzer (Basic) 199W-CDMA with HSPA+ 199GSM/EDGE/EDGE Evo 200802.16 OFDMA (WiMAX/WiBro) 200Vector Signal Analyzer (VXA) 200Phase Noise 201

iDEN/WiDEN/MotoTalk Analyzer Measurement Application Reference vii

Table of Contents

Noise Figure 201Analog Demod 201TD-SCDMA with HSPA/8PSK 202cdma2000 2021xEV-DO 202LTE 202LTE TDD 203DVB-T/H with T2 203DTMB (CTTB) 203ISDB-T 204CMMB 204Combined WLAN 204Combined Fixed WiMAX 205802.16 OFDM (Fixed WiMAX) 205iDEN/WiDEN/MOTOTalk 205Remote Language Compatibility 206SCPI Language Compatibility 20689601 VSA 206Bluetooth 207Digital Cable TV 207WLAN 208MSR 208Application Mode Number Selection (Remote Command Only) 208

Application Mode Catalog Query (Remote Command Only) 210Application Identification (Remote Commands Only) 210

Current Application Model 211Current Application Revision 211Current Application Options 211

Application Identification Catalog (Remote Commands Only) 212Application Catalog Number of Entries 212Application Catalog Model Numbers 212Application Catalog Revision 212Application Catalog Options 213

Detailed List of Modes 2131xEV-DO 213802.16 OFDMA (WiMAX/WiBro) 214802.16 OFDM (Fixed WiMAX) 21489601 VSA 214Analog Demod 215Bluetooth 215cdma2000 216CMMB 216Combined WLAN 216

viii iDEN/WiDEN/MotoTalk Analyzer Measurement Application Reference

Table of Contents

Combined Fixed WiMAX 217Digital Cable TV 217DTMB (CTTB) 217DVB-T/H with T2 217EMI Receiver 218GSM/EDGE/EDGE Evo 218iDEN/WiDEN/MOTOTalk 218IQ Analyzer (Basic) 219ISDB-T 219LTE 219LTE TDD 220MSR 220Noise Figure 220Phase Noise 221Remote Language Compatibility 221SCPI Language Compatibility 221Spectrum Analyzer 222TD-SCDMA with HSPA/8PSK 222Vector Signal Analyzer (VXA) 222W-CDMA with HSPA+ 223WLAN 223

Global Settings 223Global Center Freq 224Restore Defaults 224

Mode Setup 226Spectrum 226Fixed Equalization 227

Fixed EQ Mode 227Freq Response Register 227Fixed Equalization Mapping 228

Radio Standards 228MQAM Format 228

M4QAM 229M16QAM 229M64QAM 229

Slot Format 229Full Slot Reserved (Inbound) 230Random Access (Inbound) 231New 6:1 Reserved Pseudo (Inbound) 231Full Slot Enhanced 6:1 (Inbound) 231WiDEN (Inbound) 231Full Slot Reserved (Outbound) 232New 6:1 Reserved (Outbound) 232

iDEN/WiDEN/MotoTalk Analyzer Measurement Application Reference ix

Table of Contents

Color Code 232Carrier Config 232

25 kHz 23350 kHz 23350 kHz Outer 23375 kHz 234100 kHz 234

Global Settings 234

6 System Functions 235File 236

File Explorer 236Print 237Maximize/Restore Down 237

Maximize 237Restore Down 237

Page Setup 237Print 238Maximize 239Restore Down 239Minimize 239Exit 240

Print 241System 242

Show 242Errors 242

Previous Page 243Next Page 244History 244Verbose SCPI On/Off 244Refresh 245Clear Error Queue 245Status 245Input Overload Enable (Remote Command Only) 245

System 246Show System contents (Remote Command Only) 247

Hardware 247LXI 248

Power On 248Mode and Input/Output Defaults 249User Preset 249Last State 250Power On Application 250Configure Applications 251

x iDEN/WiDEN/MotoTalk Analyzer Measurement Application Reference

Table of Contents

Preloading Applications 252Access to Configure Applications utility 252Virtual memory usage 252Select All 253Deselect All 253Move Up 253Move Down 253Select/Deselect 253Save Changes and Exit 254Exit Without Saving 254

Restore Power On Defaults 254Configure Applications - Instrument boot-up 255Configure Applications - Windows desktop 255Configure Applications - Remote Commands 255

Configuration list (Remote Command Only) 256Configuration Memory Available (Remote Command Only) 256Configuration Memory Total (Remote Command Only) 256Configuration Memory Used (Remote Command Only) 256Configuration Application Memory (Remote Command Only) 257

Alignments 257Auto Align 257

Normal 258Partial 259Off 259All but RF 260Alert 260Execute Expired Alignments (Remote Command Only) 263

Align Now 264All 264All but RF 266RF 267

Show Alignment Statistics 268Restore Align Defaults 273Backup or Restore Align Data 274

Alignment Data Wizard 274Perform Backup (Remote Command Only) 279Perform Restore (Remote Command Only) 280

Advanced 280Characterize Preselector 280

Timebase DAC 281Calibrated 282User 282

I/O Config 283

iDEN/WiDEN/MotoTalk Analyzer Measurement Application Reference xi

Table of Contents

GPIB 283GPIB Address 283GPIB Controller 284

SCPI LAN 285SCPI Telnet 285SCPI Socket 286SICL Server 286HiSLIP Server 287SCPI Socket Control Port (Remote Command Only) 287

Reset Web Password 288LXI 288

LAN Reset 288System IDN Response 289

Factory 289User 289

Query USB Connection (Remote Command Only) 290USB Connection Status (Remote Command Only) 290USB Packet Count (Remote Command Only) 291

Restore Defaults 291Restore Input/Output Defaults 291Restore Power On Defaults 292Restore Align Defaults 292Restore Misc Defaults 293Restore Mode Defaults (All Modes) 294All 295

Control Panel 296Licensing 297Security 299

USB 299Read-Write 299Read only 299

Diagnostics 300Show Hardware Statistics 300

SCPI for Show Hardware Statistics ( Remote Commands Only) 301Service 304Internet Explorer 304System Remote Commands (Remote Commands Only) 304

System Powerdown (Remote Command Only) 305List installed Options (Remote Command Only) 305Lock the Front-panel keys (Remote Command Only) 305List SCPI Commands (Remote Command Only) 306SCPI Version Query (Remote Command Only) 306Date (Remote Command Only) 306

xii iDEN/WiDEN/MotoTalk Analyzer Measurement Application Reference

Table of Contents

Time (Remote Command Only) 307

7 Trigger Functions 309Trigger 310

Free Run 310Video (IF Envelope) 310

Trigger Level 311Trig Slope 311Trig Delay 312Trig Holdoff 312Holdoff Type 313

External 1 314Trigger Level 314Trig Slope 315Trig Delay 315Trig Holdoff 316Holdoff Type 316

Trig Reference Line 317

8 Vector Analysis 319AMPTD Y Scale (Amplitude) 322

Y Auto Scale 322Range 322

Range 323Range Auto/Man 323I Range 324Q Range Value 325I/Q Gain Ranges 327

W Path Control 328Standard Path 329W Preselector Bypass 329

Select Trace 330Couple Ref to Range 332Y Reference Value 332Y Scale Per Division 333Y Reference: Position 333Reference Line 334Y Unit Preference 334Y Log Ratio 335Vector Horiz Center 335Copy Y Scale 336

Auto Couple 337More Information 337Auto/Man Active Function keys 337

iDEN/WiDEN/MotoTalk Analyzer Measurement Application Reference xiii

Table of Contents

Auto/Man 1-of-N keys 337BW (Bandwidth) 339

Res BW 339Res BW Coupling 340FFT Window 341

Cont (Continuous Measurement/Sweep) 343File 345FREQ Channel 346

Center Freq 346Start Freq 347Stop Freq 347CF Step 348

Input/Output 349Marker 350

Select Marker 350Control Mode 351

Normal (Position) 351Delta 352Fixed 352Off 353Coupling of Delta and Reference Markers 353

Marker Properties 354Select Marker 354Relative To 354Complex Format 355Marker Trace 356Marker Count 356

Marker Table 357Marker Position 357

Marker X 358SCPI only X position commands 359

Marker Z 360Marker Y 361Marker Y Imag (Imaginary) 362

Couple Markers 363All Markers Off 364Coupling of Delta and Reference Markers 364

Marker -> (Marker To) 366Mkr -> CF (Center Frequency) 366Mkr -> CF Step 366Mkr -> Start 367Mkr -> Stop 367Mkr Delta -> Span 367

xiv iDEN/WiDEN/MotoTalk Analyzer Measurement Application Reference

Table of Contents

Mkr -> Ref Lvl 367Counter -> CF (Center Frequency) 368Mkr Delta -> CF (Center Frequency) 368

Marker Function 369Select Marker 369Band/Interval Power 370

Frequency-domain data 370Time-domain data 370Band Power Calculation 370

Band/Interval Density 372Frequency-domain data 372Time-domain data 372Band Density Calculation 372

Band Adjust 373Band/Interval Center 373Band/Interval Span 374Band/Interval Left 374Band/Interval Right 375

Band Power and Delta Markers 375Meas 377

Remote Measurement Functions 377Measurement Group of Commands 378Current Measurement Query (Remote Command Only) 380Limit Test Current Results (Remote Command Only) 380Data Query (Remote Command Only) 380Calculate/Compress Trace Data Query (Remote Command Only) 381Calculate Peaks of Trace Data (Remote Command Only) 386Format Data: Numeric Data (Remote Command Only) 387Format Data: Byte Order (Remote Command Only) 388

Meas Setup 389Avg Number 389Average Mode 390Average Setup 390

Average Type 391Fast Average 391Update Rate 392

PhNoise Opt 393Best Close-in FNoise 393Best Wide-offset FNoise 394

Meas Preset 394Mode 395Mode Preset 396

How-To Preset 397

iDEN/WiDEN/MotoTalk Analyzer Measurement Application Reference xv

Table of Contents

Mode Setup 399Peak Search 400

Select Marker 400Next Peak (Next Lower Amptd) 401Next Higher Amptd 401Next Right 402Next Left 402Mkr -> CF (Center Frequency) 402Continuous Peak Search 403Min Search 403Mkr -> Ref Lvl (Reference Level) 404

Print 405Quick Save 406Recall 408

State 408More Information 410From File 410Edit Register Names 412

Register 1 thru Register 16 412Register 1 thru Register 16 413

Trace 414Import Trace Data 415

Data 1 415Data 2 416Data 3 416Data 4 416Data 5 416Data 6 416Display in Selected Trace 416

Open 417Restart 418

More Information 418Save 420

State 420To File . . . 421Edit Register Names 423

More Information 423Register 1 thru Register 16 424

Register 1 thru Register 16 424Mass Storage Catalog (Remote Command Only) 425Mass Storage Change Directory (Remote Command Only) 425Mass Storage Copy (Remote Command Only) 426Mass Storage Device Copy (Remote Command Only) 426

xvi iDEN/WiDEN/MotoTalk Analyzer Measurement Application Reference

Table of Contents

Mass Storage Delete (Remote Command Only) 426Mass Storage Data (Remote Command Only) 427Mass Storage Make Directory (Remote Command Only) 427Mass Storage Move (Remote Command Only) 427Mass Storage Remove Directory (Remote Command Only) 428

Data (Export) 428Export Trace Data 429

Trace 1 429Trace 2 430Trace 3 430Trace 4 430Trace 5 430Trace 6 430Include Header 431

Save As . . . 431Screen Image 431

Themes 4333D Color 4333D Monochrome 433Flat Color 433Flat Monochrome 434

Save As 434Single (Single Measurement/Sweep) 435

More Information 435Source 436SPAN X Scale 437

Span 437Full Span 437Signal Track 438Select Trace 438X Scale 440X Reference Value 440X Width 441X Reference Position 441Freq Annotation 442All Frequency Points 442Copy X Scale 443

Sweep/Control 444Main Time 444Pause / Resume 445Gate 445

Gate 445Gate Length 446

iDEN/WiDEN/MotoTalk Analyzer Measurement Application Reference xvii

Table of Contents

Gate Delay 446Freq Points 447

System 448Trace/Detector 449

Select Trace 449Data 450

Channel 1 451Spectrum 451Inst Spectrum 453Main Time 453Gate Time 455Inst Main Time 455Raw Main Time 456PSD (Power Spectral Density) 457Auto Correlation 458

Statistical 461CCDF (Complementary, Cumulative Density Function) 461CDF (Cumulative Density Function) 462PDF (Probability Density Function) 463

ACP (Adjacent Channel Power) 463ACP Summary for Trace 1 464ACP Summary for Trace 2 464ACP Summary for Trace 3 464ACP Summary for Trace 4 464ACP Summary for Trace 5 465ACP Summary for Trace 6 465

OBW (Occupied Bandwidth) 465OBW Summary for Trace 1 465OBW Summary for Trace 2 465OBW Summary for Trace 3 466OBW Summary for Trace 4 466OBW Summary for Trace 5 466OBW Summary for Trace 6 466

Register 467Data 1 467Data 2 467Data 3 467Data 4 468Data 5 468Data 6 468

No Data 468Format 469Digital Demod Trace Setup 470

xviii iDEN/WiDEN/MotoTalk Analyzer Measurement Application Reference

Table of Contents

Symbol Shape 470Ideal State Shape 471Ideal State Size 471Symbol Table Format 472Time Unit 473Freq Unit 473Eye Length 474Avg Line 474

Copy to Data Register 474Phase/Delay Properties 476

Phase/Trellis Offset 476Unwrap Phase Ref 476Group Delay Aperture 477

ACP Setup 478ACP On/Off 479Carrier Freq 480Carrier Meas Noise BW 480Carrier RRC Weighting 481Carrier Filter Alpha 481Offsets 482

Offsets 482RRC Weighting (All Offsets) 485

OBW Setup (Occupied Bandwidth) 486OBW Power 487OBW Centroid > CF 487BW Limit 488

Trace Indicator Info 488Trigger 490

Free Run 490Video 490



Trig Reference Line 491User Preset 492

iDEN/WiDEN/MotoTalk Analyzer Measurement Application Reference xix

Table of Contents

User Preset 492User Preset All Modes 493Save User Preset 494

View/Display 495Display 495

Annotation 495Meas Bar On/Off 496Screen 497Active Function Values On/Off 497

Title 498Change Title 498Clear Title 499

Graticule 500System Display Settings 500

Annotation Local Settings 500Themes 501Backlight 502Backlight Intensity 502

Layout 503Preset View: Spectrum/Time 505Preset View: Statistics 505

Remote SCPI Commands and Data Queries 507:READ and :FETCh Commands 507:CALCulate:DATA 510:CALCulate:DATA:RAW 511:CALCulate:DATA:RAW:COMPlex 512:CALCulate:DATA:POINts commands 512:CALCulate:DATA:TABL commands 513

Query Table Data as Number 514Query Table Data as String 514Query Table Names 515Query Table Units 515

:CALCulate:DATA:HEADer commands 517Query Header Names 517Query Header Type 517Query Header as String 518Query Numeric Header 518

:CALC:CLIMits:FAIL? 519IQ Data Transfers 519

Fast Capture Length 520Fast Capture Word Length 521Initiate Fast Capture 521Fast Capture Block 521

xx iDEN/WiDEN/MotoTalk Analyzer Measurement Application Reference

Table of Contents

Fast Capture Pointer 522Fetch Fast Capture 522Input Sample Rate Query 523

Parameter Update Enable 523

9 Monitor Spectrum Measurement 525AMPTD Y Scale 528

Ref Value 528Attenuation 528

Dual Attenuator Configurations: 529Single Attenuator Configuration: 529(Mech) Atten 530

Attenuator Configurations and Auto/Man 531Enable Elec Atten 532

More Information 533Mechanical Attenuator Transition Rules 533When the Electronic Attenuation is enabled from a disabled state: 533Examples in the dual attenuator configuration: 533When the Electronic Attenuation is disabled from an enabled state: 533Using the Electronic Attenuator: Pros and Cons 534

Elec Atten 534Adjust Atten for Min Clip 535Pre-Adjust for Min Clip 535

Off 536Elec Atten Only 536Mech + Elec Atten 537

(Mech) Atten Step 537Scale/Div 537Presel Center 538

Proper Preselector Operation 539Preselector Adjust 539W Path Control 540

Standard Path 542W Preselector Bypass 542

Internal Preamp 543Off 544Low Band 544Full Range 545

Ref Position 545Auto Scaling 545

Auto Couple 547More Information 547Auto/Man Active Function keys 547Auto/Man 1-of-N keys 547

iDEN/WiDEN/MotoTalk Analyzer Measurement Application Reference xxi

Table of Contents

BW 549Res BW 549Video BW 550VBW:3dB RBW 552Span:3dB RBW 552


Center Freq 557Center Frequency Presets 558RF Center Freq 560Ext Mix Center Freq 561I/Q Center Freq 562

CF Step 562Input/Output 564Marker 565

Select Marker 565Properties 565

Select Marker 565Relative To 565Marker Trace 566

Couple Markers 566All Markers Off 567Marker X Axis Value (Remote Command only) 567Marker X Axis Position (Remote Command only) 568Marker Y Axis Value (Remote Command only) 568

Marker Function 569Select Marker 569Marker Function Type 569Band Adjust 569

Band/Interval Span for Frequency Domain 570Band/Interval Left for Frequency Domain 570Band/Interval Right for Frequency Domain 571

Marker To 572Meas 573

Remote Measurement Functions 573Measurement Group of Commands 574Current Measurement Query (Remote Command Only) 576Limit Test Current Results (Remote Command Only) 576Data Query (Remote Command Only) 576Calculate/Compress Trace Data Query (Remote Command Only) 577Calculate Peaks of Trace Data (Remote Command Only) 582Format Data: Numeric Data (Remote Command Only) 583

xxii iDEN/WiDEN/MotoTalk Analyzer Measurement Application Reference

Table of Contents

Format Data: Byte Order (Remote Command Only) 584Meas Setup 585

Avg/Hold Num 585Avg Mode 585Meas Preset 586

Mode 587Mode Preset 588

How-To Preset 589Mode Setup 591Peak Search 592Print 593Quick Save 594Recall 596





Open 605Restart 606




Register 1 thru Register 16 612Mass Storage Catalog (Remote Command Only) 613Mass Storage Change Directory (Remote Command Only) 613Mass Storage Copy (Remote Command Only) 614Mass Storage Device Copy (Remote Command Only) 614Mass Storage Delete (Remote Command Only) 614

iDEN/WiDEN/MotoTalk Analyzer Measurement Application Reference xxiii

Table of Contents

Mass Storage Data (Remote Command Only) 615Mass Storage Make Directory (Remote Command Only) 615Mass Storage Move (Remote Command Only) 615Mass Storage Remove Directory (Remote Command Only) 616






More Information 623Source 624Span X Scale 625

Span 625IDEN Mode Span Preset for Monitor Spectrum 626

Full Span 626Last Span 626

Sweep/Control 628Sweep Time 628Pause 628Gate 629

Gate On/Off 629Gate View On/Off 630Gate View Setup 633

Gate View Sweep Time 634Gate View Start Time 634

Gate Delay 635Gate Length 635Gate Source 636

External 1 637External 2 638

xxiv iDEN/WiDEN/MotoTalk Analyzer Measurement Application Reference

Table of Contents

RF Burst 640Control Edge/Level 643Gate Holdoff 643Gate Delay Compensation 645

More Information 646Min Fast Position Query (Remote Command Only) 646Gate Preset (Remote Command Only) 647Gate Level (Remote Command Only) 647Gate Polarity (Remote Command Only) 647

Points 648System 649Trace/Detector 650

Select Trace 650Trace Type 650Update 651Display 651Detector 652

Auto 653Clear Trace 653Clear All Traces 653

Trigger 655Free Run 655External 1 655

Trigger Level 655Trig Slope 655Trig Delay 655

External 2 655Trigger Level 655Trig Slope 655Trig Delay 655

RF Burst 655Absolute Trigger 655Relative Trigger 655Trig Slope 655Trig Delay 656

Auto/Holdoff 656Auto Trig 656Trig Holdoff 656

User Preset 657User Preset 657User Preset All Modes 658Save User Preset 659

View/Display 660

iDEN/WiDEN/MotoTalk Analyzer Measurement Application Reference xxv

Table of Contents

Display 660Annotation 660

Meas Bar On/Off 661Screen 662Active Function Values On/Off 662








Fast Capture Length 682Fast Capture Word Length 683Initiate Fast Capture 683Fast Capture Block 683Fast Capture Pointer 684Fetch Fast Capture 684Input Sample Rate Query 685


10 Measurement Functions 687

10 iDEN Power Measurement 687AMPTD Y Scale (Amplitude) 691

xxvi iDEN/WiDEN/MotoTalk Analyzer Measurement Application Reference

Table of Contents





BW (Bandwidth) 706Res BW 706Res BW Coupling 707FFT Window 708




Control Mode 717Normal (Position) 718Delta 718Fixed 719Off 719Coupling of Delta and Reference Markers 720

Select Marker 720Marker Properties 721

Select Marker 721

iDEN/WiDEN/MotoTalk Analyzer Measurement Application Reference xxvii

Table of Contents

Relative To 721Complex Format 722Marker Trace 723Marker Count 723





Marker -> (Marker To) 733Mkr -> CF (Center Frequency) 733Mkr -> CF Step 733Mkr -> Start 734Mkr -> Stop 734Mkr Delta -> Span 734Mkr -> Ref Lvl 734Counter -> CF (Center Frequency) 735Mkr Delta -> CF (Center Frequency) 735






Remote Measurement Functions 744Measurement Group of Commands 745Current Measurement Query (Remote Command Only) 747

xxviii iDEN/WiDEN/MotoTalk Analyzer Measurement Application Reference

Table of Contents

Limit Test Current Results (Remote Command Only) 747Data Query (Remote Command Only) 747Calculate/Compress Trace Data Query (Remote Command Only) 748Calculate Peaks of Trace Data (Remote Command Only) 753Format Data: Numeric Data (Remote Command Only) 754Format Data: Byte Order (Remote Command Only) 755

Meas Setup 756More Information about Meas Setup: 756Test Selection 756

OBW 756ACP 757

Test Preset 757Power Calc Uses 758

Modulation 758Full Signal 758

ACP Setup 759More Information about ACP Setup 759Offsets 760

Offset Freq 760Offset Meas Noise BW 761Offset Relative Limit 762

Carrier Meas Noise BW 763OBW Centroid -> CF 763Avg Number 763Average Mode 764Average Setup 765


OBW % Power 767OBW Limit 767


How-To Preset 771Mode Setup 773Peak Search 774

Select Marker 774Next Peak (Next Lower Amptd) 775Next Higher Amptd 775Next Right 776Next Left 776Mkr -> CF (Center Frequency) 776Continuous Peak Search 777

iDEN/WiDEN/MotoTalk Analyzer Measurement Application Reference xxix

Table of Contents

Min Search 777Mkr -> Ref Lvl (Reference Level) 778






Open 791Restart 792




Register 1 thru Register 16 798Mass Storage Catalog (Remote Command Only) 799Mass Storage Change Directory (Remote Command Only) 799Mass Storage Copy (Remote Command Only) 800Mass Storage Device Copy (Remote Command Only) 800Mass Storage Delete (Remote Command Only) 800Mass Storage Data (Remote Command Only) 801Mass Storage Make Directory (Remote Command Only) 801Mass Storage Move (Remote Command Only) 801Mass Storage Remove Directory (Remote Command Only) 802


Trace 1 803Trace 2 804

xxx iDEN/WiDEN/MotoTalk Analyzer Measurement Application Reference

Table of Contents

Trace 3 804Trace 4 804Trace 5 804Trace 6 804Include Header 805





Span 811Full Span 811Signal Track 812Select Trace 812X Scale 814X Reference Value 814X Width 815X Reference Position 815Freq Annotation 816All Frequency Points 816Copy X Scale 817

Sweep/Control 818Main Time 818Pause / Resume 819Gate 819

Gate 819Gate Length 820Gate Delay 820

Freq Points 821System 822Trace/Detector 823


Channel 1 825Spectrum 825Inst Spectrum 827

iDEN/WiDEN/MotoTalk Analyzer Measurement Application Reference xxxi

Table of Contents

Main Time 827Gate Time 829Inst Main Time 829Raw Main Time 830PSD (Power Spectral Density) 831Auto Correlation 832

ACP (Adjacent Channel Power) 835ACP Summary for Trace 1 835ACP Summary for Trace 2 835ACP Summary for Trace 3 836ACP Summary for Trace 4 836ACP Summary for Trace 5 836ACP Summary for Trace 6 836







xxxii iDEN/WiDEN/MotoTalk Analyzer Measurement Application Reference

Table of Contents










View/Display 866Display 866



Graticule 871

iDEN/WiDEN/MotoTalk Analyzer Measurement Application Reference xxxiii

Table of Contents

System Display Settings 871Annotation Local Settings 871Themes 872Backlight 873Backlight Intensity 873

Layout 874Preset View: Test Standard 876Preset View: ACP 876Preset View: ACP & OBW 876Preset View: OBW & Burst 877Measurement Views 877

Preset View: Test Standard 877Preset View: ACP 878Preset View: OWB & ACP 879Preset View: ACP & Burst 880

Front Panel Results 881Occupied Bandwidth Results 882Adjacent Channel Power Results 882






xxxiv iDEN/WiDEN/MotoTalk Analyzer Measurement Application Reference

Table of Contents



11 iDEN Demod Measurement 901AMPTD Y Scale (Amplitude) 908





BW (Bandwidth) 923FFT Window 923





Normal (Position) 933Delta 934Fixed 934Off 935

iDEN/WiDEN/MotoTalk Analyzer Measurement Application Reference xxxv

Table of Contents

Coupling of Delta and Reference Markers 935Marker Properties 936

Select Marker 936Relative To 936Complex Format 937Marker Trace 938Marker Count 938





Marker -> (Marker To) 948Mkr -> CF (Center Frequency) 948Mkr -> CF Step 948Mkr -> Start 949Mkr -> Stop 949Mkr Delta -> Span 949Mkr -> Ref Lvl 949Counter -> CF (Center Frequency) 950Mkr Delta -> CF (Center Frequency) 950






xxxvi iDEN/WiDEN/MotoTalk Analyzer Measurement Application Reference

Table of Contents


Meas Setup 971More Information about Meas Setup: 971Test Selection 971

EVM 971PvT 972BER 972

Test Preset 973More Information about Test Preset: 973

EVM Setup 973Analysis Subchannel 974

0 (LO) 9741 (LI) 9742 (RI) 9743 (RO) 975

WiDEN Carrier 975EVM Test Limit 975

BER Setup 976BER Slots 976BER Test Limit 977

Search Length 977Analysis Slot 978Avg Number 978Average Mode 979Average Setup 980


Extend Freq Lock Range 982Normalize 983Advanced 983

Filter Alpha 983Time Scale Factor 984Sync/Pilot Symbols 984Droop 985

iDEN/WiDEN/MotoTalk Analyzer Measurement Application Reference xxxvii

Table of Contents

Pilot Tracking 985Mode 986Mode Preset 987








Open 1008Restart 1009




Register 1 thru Register 16 1015

xxxviii iDEN/WiDEN/MotoTalk Analyzer Measurement Application Reference

Table of Contents

Mass Storage Catalog (Remote Command Only) 1016Mass Storage Change Directory (Remote Command Only) 1016Mass Storage Copy (Remote Command Only) 1017Mass Storage Device Copy (Remote Command Only) 1017Mass Storage Delete (Remote Command Only) 1017Mass Storage Data (Remote Command Only) 1018Mass Storage Make Directory (Remote Command Only) 1018Mass Storage Move (Remote Command Only) 1018Mass Storage Remove Directory (Remote Command Only) 1019







Span 1028Full Span 1028Select Trace 1029X Scale 1030X Reference Value 1030X Width 1031X Reference Position 1032Freq Annotation 1032All Frequency Points 1033Copy X Scale 1033

Sweep/Control 1035Pause / Resume 1035

System 1036

iDEN/WiDEN/MotoTalk Analyzer Measurement Application Reference xxxix

Table of Contents

Trace/Detector 1037Select Trace 1037Data 1038

Pre Demod 1039Spectrum 1039Inst Spectrum 1040Search Time 1040Time 1040Raw Main Time 1040

PvT 1040PvT Time 1041PvT Summary 1041WiDEN Carr0 PvT Time 1041WiDEN Carr1 PvT Time 1041WiDEN Carr2 PvT Time 1042WiDEN Carr3 PvT Time 1042

BER 1042BER Overall Summary 1042BER Slot Summary 1042

Overlaid Demod 1043Overlaid IQ Meas Time 1043Overlaid IQ Ref Time 1043Overlaid Error Vector Time 1043Overlaid Error Vector Spectrum 1043Overlaid IQ Mag Error 1044Overlaid IQ Phase Error 1044

Subchannel Demod 1044Subchannel IQ Meas Time 1044Subchannel IQ Ref Time 1045Subchannel Error Vector Time 1045Subchannel IQ Mag Error 1045Subchannel IQ Phase Error 1045

Tables 1045Composite Error Summary 1046Composite Symbols 1046Subchannel Error Summary 1046MQAM Summary 1046

ACP (Adjacent Channel Power) 1046ACP Summary for Trace 1 1047ACP Summary for Trace 2 1047ACP Summary for Trace 3 1047ACP Summary for Trace 4 1047ACP Summary for Trace 5 1048

xl iDEN/WiDEN/MotoTalk Analyzer Measurement Application Reference

Table of Contents

ACP Summary for Trace 6 1048OBW (Occupied Bandwidth) 1048

OBW Summary for Trace 1 1048OBW Summary for Trace 2 1048OBW Summary for Trace 3 1049OBW Summary for Trace 4 1049OBW Summary for Trace 5 1049OBW Summary for Trace 6 1049








OBW Setup (Occupied Bandwidth) 1069OBW Power 1070OBW Centroid > CF 1070

iDEN/WiDEN/MotoTalk Analyzer Measurement Application Reference xli

Table of Contents

BW Limit 1071Trace Indicator Info 1071

Trigger 1073Free Run 1073Video 1073





View / Display 1078Display 1078





Layout 1086Preset View: Test Standard 1088Preset View: PvT Rise & Fall 1088Preset View: EVM (Quad) 1088Preset View: EVM & Symbols 1089Preset View: WiDEN PvT 1089

Remote SCPI Commands and Data Queries 1091

xlii iDEN/WiDEN/MotoTalk Analyzer Measurement Application Reference

Table of Contents

:READ and :FETCh Commands 1091:CALCulate:DATA 1094:CALCulate:DATA:RAW 1095:CALCulate:DATA:RAW:COMPlex 1096:CALCulate:DATA:POINts commands 1096:CALCulate:DATA:TABL commands 1097







12 MotoTalk Measurement 1109AMPTD Y Scale (Amplitude) 1114



Select Trace 1120Couple Ref to Range 1121Y Reference Value 1121Y Scale Per Division 1122Y Reference: Position 1122Reference Line 1123Y Unit Preference 1123

iDEN/WiDEN/MotoTalk Analyzer Measurement Application Reference xliii

Table of Contents

Y Log Ratio 1124Vector Horiz Center 1125Copy Y Scale 1125


BW (Bandwidth) 1129FFT Window 1129





Normal (Position) 1139Delta 1140Fixed 1140Off 1141Coupling of Delta and Reference Markers 1141

Marker Properties 1142Select Marker 1142Relative To 1142Complex Format 1143Marker Trace 1144Marker Count 1144





Marker -> (Marker To) 1154Mkr -> CF (Center Frequency) 1154

xliv iDEN/WiDEN/MotoTalk Analyzer Measurement Application Reference

Table of Contents

Mkr -> CF Step 1154Mkr -> Start 1155Mkr -> Stop 1155Mkr Delta -> Span 1155Mkr -> Ref Lvl 1155Counter -> CF (Center Frequency) 1156Mkr Delta -> CF (Center Frequency) 1156







Meas Setup 1177Test Preset 1177Search Length 1177Analysis Slot 1178Avg Number 1178Average Mode 1179Average Setup 1180


iDEN/WiDEN/MotoTalk Analyzer Measurement Application Reference xlv

Table of Contents

Normalize 1182Advanced 1182

Gaussian BT 1182Symbol Rate 1183Burst Search 1183









Open 1207Restart 1208


State 1210To File . . . 1211

xlvi iDEN/WiDEN/MotoTalk Analyzer Measurement Application Reference

Table of Contents

Edit Register Names 1213More Information 1213Register 1 thru Register 16 1214

Register 1 thru Register 16 1214Mass Storage Catalog (Remote Command Only) 1215Mass Storage Change Directory (Remote Command Only) 1215Mass Storage Copy (Remote Command Only) 1216Mass Storage Device Copy (Remote Command Only) 1216Mass Storage Delete (Remote Command Only) 1216Mass Storage Data (Remote Command Only) 1217Mass Storage Make Directory (Remote Command Only) 1217Mass Storage Move (Remote Command Only) 1217Mass Storage Remove Directory (Remote Command Only) 1218







Span 1227Full Span 1227Select Trace 1228X Scale 1229X Reference Value 1229X Width 1230X Reference Position 1231Freq Annotation 1231All Frequency Points 1232

iDEN/WiDEN/MotoTalk Analyzer Measurement Application Reference xlvii

Table of Contents

Copy X Scale 1232Sweep/Control 1234

Pause / Resume 1234System 1235Trace/Detector 1236


Pre Demod 1238Spectrum 1238Inst Spectrum 1239Search Time 1239Time 1239Raw Main Time 1239

Error Vector Time 1239Slot Error Vector Time 1240Error Summary 1240Slot Error Summary 1240ACP (Adjacent Channel Power) 1241

ACP Summary for Trace 1 1241ACP Summary for Trace 2 1241ACP Summary for Trace 3 1241ACP Summary for Trace 4 1242ACP Summary for Trace 5 1242ACP Summary for Trace 6 1242




Symbol Shape 1247Ideal State Shape 1248

xlviii iDEN/WiDEN/MotoTalk Analyzer Measurement Application Reference

Table of Contents

Ideal State Size 1249Symbol Table Format 1249Time Unit 1250Freq Unit 1250Eye Length 1251Avg Line 1251











User Preset 1269User Preset All Modes 1270

iDEN/WiDEN/MotoTalk Analyzer Measurement Application Reference xlix

Table of Contents

Save User Preset 1271View/Display 1272

Display 1272Annotation 1272

Meas Bar On/Off 1273Screen 1274Active Function Values On/Off 1274




Layout 1280Preset View: Test Standard 1282Preset View: Slot 1282Measurement Views 1282Front Panel Results 1284





Fast Capture Length 1298Fast Capture Word Length 1299Initiate Fast Capture 1299Fast Capture Block 1299

l iDEN/WiDEN/MotoTalk Analyzer Measurement Application Reference

Table of Contents

Fast Capture Pointer 1300Fetch Fast Capture 1300Input Sample Rate Query 1301


iDEN/WiDEN/MotoTalk Analyzer Measurement Application Reference li

Table of Contents

lii iDEN/WiDEN/MotoTalk Analyzer Measurement Application Reference

1 About the Analyzer

The X-Series signal analyzer measures and monitors complex RFand microwave signals. Analog baseband analysis is available onMXA. The analyzer integrates traditional spectrum measurementswith advanced vector signal analysis to optimize speed, accuracy,and dynamic range. The analyzer has Windows 7 built in as anoperating system, which expands its usability.

With a broad set of applications and demodulation capabilities, anintuitive user interface, outstanding connectivity and powerful one-button measurements, the analyzer is ideal for both R&D andmanufacturing engineers working on cellular, emerging wirelesscommunications, general purpose, aerospace and defenseapplications.

Keysight X-Series Signal AnalyzeriDEN/WiDEN/MotoTalk Analyzer Measurement Application Reference

53

1 About the AnalyzerInstalling Application Software

Installing Application Software

If you want to install a measurement application after your initial hardware purchase, you need only tolicense it. All of the available applications are loaded in your analyzer at the time of purchase.

Thus, when you purchase a new application, you will receive an entitlement certificate that you can use toobtain a license key for that application. To activate the new measurement application, enter the licensekey that you obtain into the Signal Analyzer.

For the latest information on Keysight Signal Analyzer measurement applications and upgrade kits, visitthe following internet URL.

http://www.agilent.com/find/sa_upgrades

Viewing a License Key

Measurement applications that you purchased with your instrument have been installed and activated atthe factory before shipment. The instrument requires a unique License Key for every measurementapplication purchased. The license key is a hexadecimal string that is specific to your measurementapplication, instrument model number and serial number. It enables you to install, or reactivate, thatparticular application.

Press System, Show, System to display the measurement applications that are currently licensed in youranalyzer.

Go to the following location to view the license keys for the installed measurement applications:

C:\Program Files\Agilent\Licensing

You may want to keep a copy of your license key in a secure location. To do this, you can print out a copy ofthe display showing the license numbers. If you should lose your license key, call your nearest KeysightTechnologies service or sales office for assistance.

Obtaining and Installing a License Key

If you purchase an additional application that requires installation, you will receive an "EntitlementCertificate", which may be redeemed for a license key for one instrument. To obtain your license key, followthe instructions that accompany the certificate.

Installing a license key for the selected application can be done automatically using a USB memory device.To do this, you copy the license file to the USB memory device, at the root level. Follow the instructionsthat come with your software installation kit.

Installing a license key can also be done manually using the built-in license management application,which may be found via the instrument front panel keys at System, Licensing. . . , or on-disk at:

C:\Programming Files\Agilent\Licensing

You can also use these procedures to reinstall a license key that has been accidentally deleted, or lost dueto a memory failure.

Updating Measurement Application Software

All the software applications were loaded at the time of original instrument manufacture. It is a good ideato regularly update your software with the latest available version. This helps to ensure that you receive

54 iDEN/WiDEN/MotoTalk Analyzer Measurement Application Reference

http://www.agilent.com/find/sa_upgradeshttp://www.agilent.com/find/sa_upgrades

1 About the AnalyzerInstalling Application Software

any improvements and expanded functionality.

Because the software was loaded at the initial purchase, further additional measurement applications maynow be available. If the application you are interested in licensing is not available, you will need to do asoftware update. (To display a list of installed applications, press System, Show, System.)

Check the appropriate page of the Keysight web site for the latest available software versions, accordingto the name of your instrument, as follows:

http://www.agilent.com/find/pxa_software

http://www.agilent.com/find/mxa_software

http://www.agilent.com/find/exa_software

http://www.agilent.com/find/cxa_software

You can load the updated software package into the analyzer from a USB drive, or directly from theinternet. An automatic loading program is included with the files.

iDEN/WiDEN/MotoTalk Analyzer Measurement Application Reference 55

http://www.agilent.com/find/pxa_softwarehttp://www.agilent.com/find/pxa_softwarehttp://www.agilent.com/find/mxa_softwarehttp://www.agilent.com/find/mxa_softwarehttp://www.agilent.com/find/exa_softwarehttp://www.agilent.com/find/exa_softwarehttp://www.agilent.com/find/cxa_softwarehttp://www.agilent.com/find/cxa_software

1 About the AnalyzerX-Series Options and Accessories

X-Series Options and Accessories

You can view an online list of available Options and Accessories for your instrument as follows:

1. Browse to one of the following URLs, according to the product name of your analyzer:

www.agilent.com/find/cxa

www.agilent.com/find/exa

www.agilent.com/find/mxa

www.agilent.com/find/pxa

2. The home page for your instrument appears (in some cases, you may see an initial splash screencontaining a button named View the Webpage, which you should click to display the home page).

3. Locate the Options tab, as highlighted in the example below, which shows the home page for the MXA.

4. Click the Options tab, to display a list of available options and accessories for your instrument.


http://www.agilent.com/find/cxahttp://www.agilent.com/find/exahttp://www.agilent.com/find/mxahttp://www.agilent.com/find/pxa

1 About the AnalyzerFront-Panel Features

Front-Panel Features

The instrument's Front-panel features are fully detailed in the section "Front-Panel Features" (under thechapter "Front and Rear Panel Features") of the document:

Getting Started Guide

If you are viewing this information as a Help file in the instrument, then you can click on the link above toopen the PDF document.


http://www.agilent.com/find/xseries_getting_started_guidehttp://www.agilent.com/find/xseries_getting_started_guidehttp://www.agilent.com/find/xseries_getting_started_guide

1 About the AnalyzerDisplay Annotations

Display Annotations

Display Annotations are fully detailed under the chapter "Front and Rear Panel Features" of the document:





1 About the AnalyzerRear-Panel Features

Rear-Panel Features

The instrument's Rear-panel features are fully detailed in the section "Rear-Panel Features" (under thechapter "Front and Rear Panel Features") of the document:





1 About the AnalyzerWindow Control Keys

Window Control Keys

The instrument provides three front-panel keys for controlling windows. They are Multi Window, Zoom,and Next Window. These are all immediate action keys.

Multi-Window

The Multi Window front-panel key will toggle you back and forth between the Normal View and the lastMulti Window View (Zone Span, Trace Zoom or Spectrogram) that you were in, when using the Swept SAmeasurement of the Spectrum Analyzer Mode. It remembers which View you were in through a Preset.This previous view is set to Zone Span on a Restore Mode Defaults.

Key Path Front-panel key

Initial S/W Revision Prior to A.02.00

Zoom

Zoom is a toggle function. Pressing this key once increases the size of the selected window. Pressing thekey again returns the window to the original size.

When Zoom is on for a window, that window will get the entire primary display area. The zoomed window,since it is the selected window, is outlined in green.

Zoom is local to each Measurement. Each Measurement remembers its Zoom state. The Zoom state ofeach Measurement is part of the Modes state.

Data acquisition and processing for the other windows continues while a window is zoomed, as does allSCPI communication with the other windows.

Remote Command :DISPlay:WINDow:FORMat:ZOOM



Remote Command :DISPlay:WINDow:FORMat:TILE

Example :DISP:WIND:FORM:ZOOM sets zoomed:DISP:WIND:FORM:TILE sets un-zoomed

Preset TILE


Next Window

Selects the next window of the current view.When the Next Window key is pressed, the next window in theorder of precedencebecomes selected. If the selected window was zoomed, the next window will also bezoomed.

The window numbers are as follows. Note that these numbers also determine the order of precedence(that is, Next Window goes from 1 to 2, then 2 to 3, etc.):

RTSA measurements:

Only two windows are available in the Spectrogram view under the Spectrum measurement and up tothree windows are available in the Power vs. Time measurement, depending on the view set up.

Remote Command :DISPlay:WINDow[:SELect]

:DISPlay:WINDow[:SELect]?

Example :DISP:WIND 1

Preset 1

Min 1

Max If is greater than the number of windows, limit to


One and only one window is always selected. The selected window has the focus; this means that allwindow-specific key presses apply only to that window. You can tell which window is selected by the thickgreen border around it. If a window is not selected, its boundary is gray.

If a window in a multi-window display is zoomed it is still outlined in green. If there is only one window, thegreen outline is not used. This allows the user to distinguish between a zoomed window and a display withonly one window.



The selected window is local to each Measurement. Each Measurement remembers which window isselected. The selected window for each Measurement is remembered in Mode state.

When this key is pressed in Help Mode, it toggles focus between the table of contents window and thetopic pane window.

Full Screen

When Full Screen is pressed the measurement window expands horizontally over the entire instrumentdisplay. The screen graticule area expands to fill the available display area.

It turns off the display of the softkey labels, however the menus and active functions still work. (Though itwould obviously be very hard to navigate without the key labels displayed.) Pressing Full Screen againwhile Full Screen is in effect cancels Full Screen.

Note that the banner and status lines are unaffected. You can get even more screen area for your datadisplay by turning off the Meas Bar (in the Display menu) which also turns off the settings panel.

Full Screen is a Meas Global function. Therefore it is cancelled by the Preset key.

Key Path Display

Remote Command :DISPlay:FSCReen[:STATe] OFF|ON|0|1

:DISPlay:FSCReen[:STATe]?

Preset Unaffected by Preset but set to Off by Restore Misc Defaults or shutdown and restart

State Saved Not saved in instrument state.

BackwardsCompatibility SCPI

:DISPlay:MENU[:STATe] OFF|ON|0|1

This emulates ESA full screen functionality, which is the same as the FSCReen command in PSAexcept that the sense of on/off is reversed (that is, OFF means the menus are OFF, so Fullscreen isON) and the default is ON (meaning Fullscreen is OFF).

Backwards CompatibilityNotes

In ESA/PSA, Full Screen was turned on with a softkey, so pressing any other key turned Full Screenoff. In the X-Series, because a hardkey is provided to turn this function on and off, pressing anyother key no longer turns off Full Screen


Display Enable (Remote Command Only)

Turns the display on/off, including the display drive circuitry. The backlight stays lit so you can tell that theinstrument is on. The display enable setting is mode global. The reasons for turning the display off arethree:

To increase speed as much as possible by freeing the instrument from having to update the display

To reduce emissions from the display, drive circuitry

For security purposes

If you have turned off the display:



and you are in local operation, the display can be turned back on by pressing any key or by sending theSYSTem:DEFaults MISC command or the DISPlay:ENABle ON (neither *RST nor SYSTem:PRESet enablethe display.)

and you are in remote operation, the display can be turned back on by pressing the Local or Esc keys orby sending the SYSTem:DEFaults MISC command or the DISPlay:ENABle ON (neither *RST norSYSTem:PRESet enable the display.)

and you are using either the SYSTem:KLOCk command or GPIB local lockout, then no front-panel keypress will turn the display back on. You must turn it back on remotely.

Remote Command :DISPlay:ENABle OFF|ON|0|1

:DISPlay:ENABle?

Example DISP:ENAB OFF

Couplings DISP:ENAB OFF turns Backlight OFF and DISP:ENAB ON turns Backlight ON. However, settings ofBacklight do not change the state of DISP:ENAB

Preset On

Set by SYST:DEF MISC, but Not affected by *RST or SYSTem:PRESet.

State Saved Not saved in instrument state.

Backwards CompatibilityNotes

SYST:PRES no longer turns on DISPlay:ENABle as it did in legacy analyzers



1 About the AnalyzerMouse and Keyboard Control

Mouse and Keyboard Control

If you do not have access to the instrument front-panel, there are several ways that a mouse and PCKeyboard can give you access to functions normally accessed using the front-panel keys.

Right-Click

If you plug in a mouse and right-click on the analyzer screen, a menu will appear as below:

Placing the mouse on one of the rows marked with a right arrow symbol will cause that row to expand, asfor example below where the mouse is hovered over the Utility row:



This method can be used to access any of the front-panel keys by using a mouse; as for example if you areaccessing the instrument through Remote Desktop.

The array of keys thus available is shown below:



PC Keyboard

If you have a PC keyboard plugged in (or via Remote Desktop), certain key codes on the PC keyboard mapto front-panel keys on the GPSA front panel. These key codes are shown below:

Front-panel key Key code

Frequency CTRL+SHIFT+F

Span CTRL+SHIFT+S

Amplitude CTRL+SHIFT+A

Input/Output CTRL+SHIFT+O

View/Display CTRL+SHIFT+V

Trace/Detector CTRL+ALT+T

Auto Couple CTRL+SHIFT+C

Bandwidth CTRL+ALT+B

Source CTRL+ALT-U

Marker CTRL+ALT+K

Peak Search CTRL+ALT+P

Marker To CTRL+ALT+N

Marker Function CTRL+ALT+F

System CTRL+SHIFT+Y

Quick Save CTRL+Q

Save CTRL+S

Recall CTRL+R

Mode Preset CTRL+M

User Preset CTRL+U

Print CTRL+P

File CTRL+SHIFT+L

Mode CTRL+SHIFT+M

Measure CTRL+ALT+M

Mode Setup CTRL+SHIFT+E

Meas Setup CTRL+ALT+E

Trigger CTRL+SHIFT+T

Sweep/Control CTRL+SHIFT+W

Restart CTRL+ALT+R

Single CTRL+ALT+S

Cont CTRL+ALT+C

Zoom CTRL+SHIFT+Z

Next Window CTRL+SHIFT+N

Split Screen CTRL+L



Front-panel key Key code

Full Screen CTRL+SHIFT+B

Return CTRL+SHIFT+R

Mute Mute

Inc Audio Volume Up

Dec Audio Volume Down

Help F1

Control CTRL

Alt ALT

Enter Return

Cancel Esc

Del Delete

Backspace Backspace

Select Space

Up Arrow Up

Down Arrow Down

Left Arrow Left

Right Arrow Right

Menu key 1 CTRL+SHIFT+F1







Backspace BACKSPACE

Enter ENTER

Tab Tab

1 1

2 2

3 3

4 4

5 5

6 6

7 7

8 8

9 9

0 0



This is a pictorial view of the table:


1 About the AnalyzerInstrument Security & Memory Volatility

Instrument Security & Memory Volatility

If you are using the instrument in a secure environment, you may need details of how to clear or sanitize itsmemory, in compliance with published security standards of the United States Department of Defense, orother similar authorities.

For X-Series analyzers, this information is contained in the document "Security Features and Document ofVolatility". This document is not included in the Documentation CD, or the instrument's on-disk library, butit may be downloaded from Keysight's web site.

To obtain a copy of the document, click on or browse to the following URL:

http://www.agilent.com/find/security

To locate and download the document, select Model Number "N9020A", then click "Submit". Then, followthe on-screen instructions to download the file.


http://www.agilent.com/find/security

1 About the AnalyzerInstrument Security & Memory Volatility


2 About the iDEN/WiDEN/MotoTalk AnalyzerMeasurement Application

This chapter provides overall information on the Agilent N6149AiDEN/WiDEN/MotoTalk Analyzer Measurement Application anddescribes the measurements made by the analyzer.


71

2 About the iDEN/WiDEN/MotoTalk Analyzer Measurement ApplicationWhat Does the iDEN/WiDEN/MotoTalk Analyzer Measurement Application Do?

What Does the iDEN/WiDEN/MotoTalk Analyzer MeasurementApplication Do?

N6149A is a full-featured iDEN/WiDEN/MotoTalk signal analyzer that can help determine whether amodulated source or transmitter is working correctly. There are standard and optional settings to enablecomplete analysis of iDEN/WiDEN/MotoTalk signals.

The iDEN/WiDEN/MotoTalk Analyzer measurement application offers the following measurements:

l iDEN Power Measurement

l iDEN Demod Measurement

l MotoTalk Measurement

l VSA Vector Analysis Measurement

l Monitor Spectrum Measurement

The iDEN/WiDEN/MotoTalk Analyzer measurement application supports the following standards:

l iDEN RF Interface Specification: Layer 1, version R02.00.06

l Requirement to Modify WiDEN Power Versus Time Mask

l Motorola TalkAround: RF Interface, Talk Around Protocol (8/19/2002)


3 Programming the Analyzer

This section provides introductory information about theprogramming documentation included with your product.

l "What Programming Information is Available?" on page 74

l "STATus Subsystem " on page 94

l "IEEE 488.2 Common Commands" on page 136


73

3 Programming the AnalyzerWhat Programming Information is Available?

What Programming Information is Available?

The X-Series Documentation can be accessed through the Additional Documentation page in theinstrument Help system and is included on the Documentation DVD shipped with the instrument. It canalso be found online at: http://www.agilent.com/find/mxa_manuals.

The following resources are available to help you create programs for automating your X-Seriesmeasurements:

Resource Description

X-Series Programmer's Guide Provides general SCPI programming information on the following topics:

l Programming the X-Series Applications

l Programming fundamentals

l Programming examplesNote that SCPI command descriptions for measurement applications are not inthis book, but are in the User's and Programmer's Reference.

User's and Programmer's Reference manuals Describes all front-panel keys and softkeys, including SCPI commands for ameasurement application. Note that:

l Each measurement application has its own User's and Programmer'sReference.

l The content in this manual is duplicated in the instrument's Help (the Helpthat you see for a key is identical to what you see in this manual).

Embedded Help in your instrument Describes all front-panel keys and softkeys, including SCPI commands, for ameasurement application. Note that the content that you see in Help when youpress a key is identical to what you see in the User's and Programmer'sReference.

X-Series Getting Started Guide Provides valuable sections related to programming including:

l Licensing New Measurement Application Software - After Initial Purchase

l Configuring instrument LAN Hostname, IP Address, and Gateway Address

l Using the Windows Remote Desktop to connect to the instrument remotely

l Using the Embedded Web Server Telnet connection to communicate SCPIThis printed document is shipped with the instrument.

Keysight Application Notes Printable PDF versions of pertinent application notes.

Keysight VISA User's Guide Describes the Keysight Virtual Instrument Software Architecture (VISA) libraryand shows how to use it to develop I/O applications and instrument drivers onWindows PCs.


http://www.agilent.com/find/mxa_manualshttp://www.agilent.com/find/mxa_manuals

3 Programming the AnalyzerList of SCPI Commands

List of SCPI Commands

*CAL?*CLS*ESE *ESE?*ESR?*IDN?*OPC*OPC?*OPT?*RCL *RST*SAV *SRE *SRE?*STB?*TRG*TST?*WAICALCulate::DATA[1] | 2 | ...4?[Y | X | XY[, OFF | ON | 0 | 1] | LL |UL]CALCulate::DATA[1]|2|...4:HEADer:NAMes?CALCulate::DATA[1]|2|...4:HEADer[:NUMBer]? CALCulate::DATA[1]|2|...4:HEADer:STRing? CALCulate::DATA[1]|2|...4:HEADer:TYPE? CALCulate::DATA[1]|2|...4:NAMes?CALCulate::DATA[1]|2|...4:POINts? [OFF | ON | 0 | 1]CALCulate::DATA[1]|2|...4:RAW?CALCulate::DATA[1]|2|...4:RAW:COMPlex?CALCulate::DATA[1]|2|...4:RAW:POINts?CALCulate::DATA[1]|2|...4:TABLe:NAMes?CALCulate::DATA[1]|2|...4:TABLe[:NUMBer]? []CALCulate::DATA[1]|2|...4:TABLe:STRing? []CALCulate::DATA[1]|2|...4:TABLe:UNIT?CALCulate::MARKer:AOFFCALCulate::MARKer[1]|2|...12:CFORmat RECTangular | POLarCALCulate::MARKer[1]|2|...12:CFORmat?CALCulate::MARKer:COUPle[:STATe] OFF | ON | 0 | 1CALCulate::MARKer:COUPle[:STATe]?CALCulate::MARKer[1]|2|...12:CPSearch[:STATe] ON | OFF | 1 | 0CALCulate::MARKer[1]|2|...12:CPSearch[:STATe]?CALCulate::MARKer[1]|2|...12:FCOunt[:STATe] OFF | ON | 0 | 1CALCulate::MARKer[1]|2|...12:FCOunt[:STATe]?CALCulate::MARKer[1]|2|...12:FCOunt:X?CALCulate::MARKer[1]|2|...12:FUNCtion BPOWer | BDENsity | =OFFCALCulate::MARKer[1]|2|...12:FUNCtion?CALCulate::MARKer[1]|2|...12:FUNCtion:BAND:CENTer CALCulate::MARKer[1]|2|...12:FUNCtion:BAND:CENTer?CALCulate::MARKer[1]|2|...12:FUNCtion:BAND:LEFT CALCulate::MARKer[1]|2|...12:FUNCtion:BAND:LEFT?CALCulate::MARKer[1]|2|...12:FUNCtion:BAND:RIGHt



CALCulate::MARKer[1]|2|...12:FUNCtion:BAND:RIGHt?CALCulate::MARKer[1]|2|...12:FUNCtion:BAND:SPAN CALCulate::MARKer[1]|2|...12:FUNCtion:BAND:SPAN?CALCulate::MARKer[1]|2|...12:FUNCtion:BDENsity:CTYPe MEAN | RMSCALCulate::MARKer[1]|2|...12:FUNCtion:BDENsity:CTYPe?CALCulate::MARKer[1]|2|...12:FUNCtion:BPOWer:CTYPe MEAN | RMSCALCulate::MARKer[1]|2|...12:FUNCtion:BPOWer:CTYPe?CALCulate::MARKer[1]|2|...12:MAXimumCALCulate::MARKer[1]|2|...12:MAXimum:LEFTCALCulate::MARKer[1]|2|...12:MAXimum:NEXTCALCulate::MARKer[1]|2|...12:MAXimum:PREViousCALCulate::MARKer[1]|2|...12:MAXimum:RIGHtCALCulate::MARKer[1]|2|...12:MINimumCALCulate::MARKer[1]|2|...12:MODE POSition | DELTa | FIXed | =OFFCALCulate::MARKer[1]|2|...12:MODE?CALCulate::MARKer[1]|2|...12:REFerence CALCulate::MARKer[1]|2|...12:REFerence?CALCulate::MARKer:TABLe[:STATe] OFF | ON | 0 | 1CALCulate::MARKer:TABLe[:STATe]?CALCulate::MARKer[1]|2|...12:TRACe CALCulate::MARKer[1]|2|...12:TRACe?CALCulate::MARKer[1]|2|...12:X CALCulate::MARKer[1]|2|...12:X?CALCulate::MARKer[1]|2|...12[:X]:POSition CALCulate::MARKer[1]|2|...12[:X]:POSition?CALCulate::MARKer[1]|2|...12:X:UNIT?CALCulate::MARKer[1]|2|...12:Y:IMAGinary CALCulate::MARKer[1]|2|...12:Y:IMAGinary?CALCulate::MARKer[1]|2|...12:Y[:REAL] CALCulate::MARKer[1]|2|...12:Y[:REAL]?CALCulate::MARKer[1]|2|...12:Y:UNIT?CALCulate::MARKer[1]|2|...12:Z CALCulate::MARKer[1]|2|...12:Z?CALCulate::MARKer[1]|2|...12:Z:UNIT?CALCulate::TRACe[1]|2|...4:ACPower:CARRier:BANDwidth|BWIDth:INTegration CALCulate::TRACe[1]|2|...4:ACPower:CARRier:BANDwidth|BWIDth:INTegration?CALCulate::TRACe[1]|2|...4:ACPower:CARRier:FILTer:RRC:ALPHa CALCulate::TRACe[1]|2|...4:ACPower:CARRier:FILTer:RRC:ALPHa?CALCulate::TRACe[1]|2|...4:ACPower:CARRier:FILTer:RRC:STATe OFF | ON| 0 | 1CALCulate::TRACe[1]|2|...4:ACPower:CARRier:FILTer:RRC:STATe?CALCulate::TRACe[1]|2|...4:ACPower:CARRier:FREQuency CALCulate::TRACe[1]|2|...4:ACPower:CARRier:FREQuency?CALCulate::TRACe[1]|2|...4:ACPower:OFFSet:FILTer:RRC:STATe OFF | ON| 0 | 1CALCulate::TRACe[1]|2|...4:ACPower:OFFSet:FILTer:RRC:STATe?CALCulate::TRACe[1]|2|...4:ACPower:OFFSet:LIST:BANDwidth|BWIDth:INTegration , ...CALCulate::TRACe[1]|2|...4:ACPower:OFFSet:LIST:BANDwidth|BWIDth:INTegration?



CALCulate::TRACe[1]|2|...4:ACPower:OFFSet:LIST:FILTer:RRC:ALPHa, ...CALCulate::TRACe[1]|2|...4:ACPower:OFFSet:LIST:FILTer:RRC:ALPHa?CALCulate::TRACe[1]|2|...4:ACPower:OFFSet:LIST:FREQuency , ...CALCulate::TRACe[1]|2|...4:ACPower:OFFSet:LIST:FREQuency?CALCulate::TRACe[1]|2|...4:ACPower:OFFSet:LIST:RCARrier , ...CALCulate::TRACe[1]|2|...4:ACPower:OFFSet:LIST:RCARrier?CALCulate::TRACe[1]|2|...4:ACPower:OFFSet:LIST:RCARrier:TEST OFF |ON | 0 | 1, ...CALCulate::TRACe[1]|2|...4:ACPower:OFFSet:LIST:RCARrier:TEST?CALCulate::TRACe[1]|2|...4:ACPower:OFFSet:LIST:STATe OFF | ON | 0 |1, ...CALCulate::TRACe[1]|2|...4:ACPower:OFFSet:LIST:STATe?CALCulate::TRACe[1]|2|...4:ACPower:STATe OFF | ON | 0 | 1CALCulate::TRACe[1]|2|...4:ACPower:STATe?CALCulate::TRACe[1]|2|...4:OBWidth:CENTroid?CALCulate::TRACe[1]|2|...4:OBWidth:LIMit:FBLimit CALCulate::TRACe[1]|2|...4:OBWidth:LIMit:FBLimit?CALCulate::TRACe[1]|2|...4:OBWidth:LIMit[:TEST] OFF | ON | 0 | 1CALCulate::TRACe[1]|2|...4:OBWidth:LIMit[:TEST]?CALCulate::TRACe[1]|2|...4:OBWidth:PERCent CALCulate::TRACe[1]|2|...4:OBWidth:PERCent?CALCulate::TRACe[1]|2|...4:OBWidth:STATe OFF | ON | 0 | 1CALCulate::TRACe[1]|2|...4:OBWidth:STATe?CALCulate:CLIMits:FAIL?CALCulate:DATA:COMPress? BLOCk | CFIT | MAXimum | MINimum | MEAN |DMEan | RMS | RMSCubed | SAMPle | SDEViation | PPHase[, [,[, [, ]]]]CALCulate:DATA[n]?CALCulate:DATA[1]|2|...|6:PEAKs? , [, AMPLitude |FREQuency | TIME]CALCulate:DATA[1]|2|...|6:PEAKs? , [, AMPLitude |FREQuency | TIME[, ALL | GTDLine | LTDLine]]CALCulate:DATA:REGister:ALL:REMoveCALCulate:DATA:REGister[1]|2|...6:EMPTy?CALCulate:DATA:REGister[1]|2|...6:REMoveCALCulate:IDEMod:BERate:LIMit:ERATeCALCulate:IDEMod:BERate:LIMit:ERATe CALCulate:IDEMod:EVMagnitude:LIMit:EVMLimit CALCulate:IDEMod:EVMagnitude:LIMit:EVMLimit?CALCulate:IPOWer:PCALculation MOD | FULLCALCulate:IPOWer:PCALculation?CALCulate:MONitor:MARKer:AOFFCALCulate:MONitor:MARKer:COUPle[:STATe] ON | OFF | 1 | 0CALCulate:MONitor:MARKer:COUPle[:STATe]?CALCulate:MONitor:MARKer[1]|2|...|12:FUNCtion NOISe | BPOWer | BDENsity |OFFCALCulate:MONitor:MARKer[1]|2|...|12:FUNCtion?CALCulate:MONitor:MARKer[1]|2|...|12:FUNCtion:BAND:LEFT CALCulate:MONitor:MARKer[1]|2|...|12:FUNCtion:BAND:LEFT?CALCulate:MONitor:MARKer[1]|2|...|12:FUNCtion:BAND:RIGHt CALCulate:MONitor:MARKer[1]|2|...|12:FUNCtion:BAND:RIGHt?



CALCulate:MONitor:MARKer[1]|2|...|12:FUNCtion:BAND:SPAN CALCulate:MONitor:MARKer[1]|2|...|12:FUNCtion:BAND:SPAN?CALCulate:MONitor:MARKer[1]|2|...|12:FUNCtion:RESult?CALCulate:MONitor:MARKer[1]|2|...|12:MAXimumCALCulate:MONitor:MARKer[1]|2|...|12:REFerence CALCulate:MONitor:MARKer[1]|2|...|12:REFerence?CALCulate:MONitor:MARKer[1]|2|...|12:TRACe CALCulate:MONitor:MARKer[1]|2|...|12:TRACe?CALCulate:MONitor:MARKer[1]|2|...|12:X CALCulate:MONitor:MARKer[1]|2|...|12:X?CALCulate:MONitor:MARKer[1]|2|...|12:X:POSition CALCulate:MONitor:MARKer[1]|2|...|12:X:POSition?CALCulate:MONitor:MARKer[1]|2|...|12:Y?CALibration[:ALL]CALibration[:ALL]?CALibration:AUTO ALERtCALibration:AUTO ON | PARTial | OFFCALibration:AUTO?CALibration:AUTO:ALERt TTEMperature | DAY | WEEK | NONECALibration:AUTO:ALERt?CALibration:AUTO:MODE ALL | NRFCALibration:AUTO:MODE?CALibration:AUTO:TIME:OFF?CALibration:DATA:BACKup CALibration:DATA:DEFaultCALibration:DATA:RESTore CALibration:EXPired?CALibration:FREQuency:REFerence

Keysight X-Series Signal Analyzer - xDevs.com N6149A iDE… · iDEN/WiDEN/Moto TalkAnalyzer...

Documents

Keysight Technologies Vector Network Analyzer

Keysight X-Series Signal Analyzerliterature.cdn.keysight.com/litweb/pdf/N9064-90003.pdfKeysight X-Series Signal Analyzer. Notices ©KeysightTechnologies,Inc. 2008-2014 Nopartofthismanualmaybe

Keysight Technologies MXA X-Series Signal Analyzer N9020A · 2016. 7. 8. · Keysight Technologies MXA X-Series Signal Analyzer N9020A 10 Hz to 3.6, 8.4, 13.6, or 26.5 GHz Data Sheet

Keysight Technologies CXA X-Series Signal Analyzer · PDF fileBasic precompliance EMI N9000A-EMC Perform EMI precompliance ... TP for transportable ... Keysight | N9000A CXA X-Series

Keysight Technologies CXA X-Series Signal Analyzer, · PDF fileCXA X-Series Signal Analyzer, Multi-touch N9000B ... LTE/LTE-Advanced FDD ... Add calibration, technical training, support,

N9042B UXA Signal Analyzer - Keysight

Keysight Technologies Scalar Network Analyzer

Keysight Technologies Signaling Analyzer Family

EXA X-Series Signal Analyzer N9010A · 2020-01-04 · Keysight Technologies EXA X-Series Signal Analyzer N9010A • 10 Hz to 3.6, 7.0, 13.6, 26.5, 32, or 44 GHz • +0.27 dB absolute

Keysight B1500A Semiconductor Device Analyzer...Keysight B1500A Semiconductor Device Analyzer of Precision Current-Voltage Analyzer Series is an all in one analyzer supporting IV,

Keysight Technologies EXA X-Series Signal Analyzer, Multi

Keysight M9290A CXA-m PXIe Signal Analyzer - xDevs.com CXA-m... · Keysight M9290A CXA-m PXIe Signal Analyzer ... 10 Chapter 1 Keysight M9290A CXA-m PXIe Signal Analyzer ... except

Keysight Technologies B1500A Semiconductor Device Analyzer

Keysight Technologies MXA X-Series Signal Analyzer N9020A€¦ · 04 | Keysight | MXA X-Series Signal Analyzer N9020A - Data Sheet Frequency and Time Specifications Frequency range

Keysight E5063A ENA Series Network Analyzer - Farnell

Keysight Technologies EXA X-Series Signal Analyzer, Multi ... config-5083.pdf · Keysight Technologies EXA X-Series Signal Analyzer, Multi-touch N9010B Configuration Guide This configuration

Keysight Technologies PXA X-Series Signal Analyzer, Multi ... · 06 | Keysight | N9030B PXA X-Series Signal Analyzer, Multi-touch - Configuration Guide Step 10. Choose measurement

Keysight Technologies N9322C Basic Spectrum Analyzer

Keysight Technologies PXA X-Series Signal Analyzer N9030A · 2018. 3. 26. · Keysight Technologies PXA X-Series Signal Analyzer N9030A 3 Hz to 3.6, 8.4, 13.6, 26.5, 43, 44, or 50