INSTALLATION GUIDE - Eddyfi › doc › Software › M2M-CAPTURE...CAPTURE PC LAUNCHING CAPTURE PC...

M2M CAPTURE SOFTWARE

I NSTALLATION GUIDE

June 2019 | Ref : CAPTURE_INSTALLATION_GUIDE_how_to_install_CAPTURE_US - B

SUMMARY

INSTALLATION OF…

1. CAPTURE SOFTWARE ON THE DEVICE

2. CAPTURE PC

3. CAPTURE VIEWER

Current release

CAPTURE SOFTWARE

INSTALLATION PROCEDURE (1/6)

1. Download the « Capture_Update_3.X.cap » file on the

website.

2. Copy the « Capture_Update_3.X.cap » file on the root

of a USB disk.

3. On GEKKO or MANTIS, press to access to the

general settings.

Note: This process shall be done with the equipment

connected to the AC Power supply.

Current release

CAPTURE SOFTWARE

INSTALLATION PROCEDURE (2/6)

4. Press on “Upgrade”.

CAPTURE SOFTWARE

Current release

INSTALLATION PROCEDURE (3/6)

5. The name of the release 3.X. appears. Press on

“Upgrade”.

Current release

CAPTURE SOFTWARE

INSTALLATION PROCEDURE (4/6)

5. Repository update.

If you press ”Yes”, you will update all the libraries (specimens,

probes, and scanner) and the applications. This procedure

will not erase the existing user files. Only the files installed

within our repository and with the same name will be replaced.

If you press “No” the libraries will not be updated.If you need

later to update the libraries, download

“Capture_Repository_Update_3.X.cap” and install them as

specified in INSTALLATION PROCEDURE 1/6

Note: If you want to remove some or all libraries, you can delete

all the folders and install the new repository.

CAPTURE SOFTWARE

Current release

INSTALLATION PROCEDURE (5/6)

7. Wait the reboot of your device

CAPTURE SOFTWARE

INSTALLATION PROCEDURE (6/6)

8. The new release is now available

In case of problem, please contact the support team

support-m2m@eddyfi.com

Current new release

CAPTURE PC

INSTALLATION PROCEDURE (1/2)

PC CONFIGURATION NEEDS

- Operating system: Windows 7 /Windows 8/ Windows 10

- Archive management tool (7z, WinRAR, WinZip...)

1. Download the « Capture_PC_3.x.exe » file and extract the contents (folder location

free).

Extracting operation generates the « Capture_PC_3.x » folder.

2. Windows UAC configuration

Better to have the Admin rights at any time to use the CAPTURE PC software.

CAPTURE PC

For this reason, you need to configure the windows UAC at the

minimum level (see next page)

INSTALLATION PROCEDURE (2/2)

2. Windows UAC configuration

- Go to user account then Modify the user account parameters in

the Control panel

- Set the scale button to its minimum level as shown on the right

picture

Once all steps are done, restart your PC

CAPTURE PC

LAUNCHING CAPTURE PC

Once PC restarted, connect the dongle on your computer.

Execute the « Go_Capture.bat » file located in the «

Capture_PC_3.x » folder.

If your PC is Windows 8 operated, you need to « execute as

Admin » after right-click on the Go_Capture file.

- The CAPTURE Home page should appear as shown on the

right picture

• If a crash occurs, please repeat the installation steps and try

again.

• In case of problems, please contact

support-m2m@eddyfi.com

CAPTURE VIEWER

INSTALLATION PROCEDURE (1/2)

You don’t need a dongle to launch the Capture Viewer

1. Upload and extraction of the file.

• Copy the file “Capture_Viewer_3.X.exe” on your computer.

• Double-click on the file.

• Select the saving location then extract.

CAPTURE VIEWER

INSTALLATION PROCEDURE (2/2)

2. Launch the viewer

• To launch the software, open the file

“Capture_Viewer_3.X.exe” and double-click on

“Go_Capture_Viewer.bat”.

CAPTURE VIEWER

LAUNCHING CAPTURE VIEWER

2. Launch the viewer

• The CAPTURE viewer Home page is displayed.

CAPTURE VIEWER

LOAD YOUR FILE (2/2)

3. Import your file

• Click on the import button to import inspection files

from the computer or an external drive.

• Select the inspection file from the Home panel then press

Start to begin the analysis.

CAPTURE VIEWER

START THE ANALYSE

4. Open the inspection file and start the analyse

• The viewer software offers basic analysis tools.

• Please refer to the document GEKKO_New features_US-A

and to the GEKKO user manual for further information

about the analysis tools.

CAPTURE VIEWER

• In case of problem, please contact the support team

support-m2m@eddyfi.com

contact - m2m@eddyfi.com