View
9
Download
0
Category
Preview:
Citation preview
®
22 www.powerteam.com
PUM
PS
Hydraulic Hand PumpSingle-Speed / Single-Acting
Reservoir capacity from 196.8 to 902 cu. cm.Single-speed pumps advance the same rate during free travel (no load) as when under load. When compared to a two-speedpump, the single-speed pump requires considerably more handle strokes to advance the cylinder to the load. Single-speedpumps are best suited for applications where there is little or no free travel.
P12
P23
• Rugged all metal construction for strength anddurability that won't burn through in weldingenvironments.
• Heavy-duty, formed metal handle provides lessflex, and less operator fatigue than round orcomposite handles.
• Convenient fill port on P23 and P55 allowspumps to be filled in a horizontal or verticalposition.
• Fill cap seal acts as safety valve to preventover-pressurizing of reservoir.
• Relief valve inboard of check valve preventsloads from drifting down.
• Large valve knob gives added control forslowly metering loads down.
700 bar
P55
DIMENSIONS (MM)
ORDERING INFORMATION
See current price list for shipping weights.
Single-Acting
Cylinders*
For Use With
OrderNo.
Volume & Pressure
Speed
Volume per Stroke (cu. cm.)
LP HP
MaximumPressure (bar)
LP HP
HandleEffort(kg)
Reservoir
OilCapacity(cu. cm.)
Usable OilCapacity(cu. cm.)
ProductWeight
(kg)OilPort
P12 1 - 1.1
- 2.6
- 700
- 207
- 700
34.1
31.8
65.8
196.8 147.6
332.9
738
2.6
5.5
7.2
390.3
902
1P23
P55
3⁄8" NPTF3⁄8" NPTF3⁄8" NPTF
LP = Low PressureHP = High Pressure
- 2.61
* (Pump includes 2-Way Valve)
E M
DNA/BC
J
GF
H
G L
K dia.
Hoses, Fittings& GaugesPages74-80
Cylinder/PumpSpeed/SelectionChart Page178
Pump/CylinderSetsPage25
Power Team hand pumps,with the angled fill port,have a built in “relief valve”protection system. Thissystem is designed toprotect over-pressurizationof the reservoir fromsudden back pressure. Thissystem also works as a sealto prevent oil leaks.
Choosing TheRight PumpPages181-184
PumpAccessoriesPages161-165
PumpNo. A B C D E F G H J K L M N P
P12 101.6 — — 101.6 342.9 85.7 55.6 — 45° 4.8 85.7 — 28.6 —
P23 158.8 330.2 88.9 141.3 346.1 108.0 82.6 261.9 38° 7.9 120.7 3/8" NPTF 41.3 —
P55 165.1 533.4 88.9 141.3 584.2 108.0 82.6 501.7 38° 7.9 120.7 3/8" NPTF 41.3 —
®
23www.powerteam.com
PUMPS
Hydraulic Hand PumpTwo-speed / Single-Acting
Reservoir capacity from 400.2 to 902 cu. cm.Two-speed pumps are designed to quickly advance the cylinder during free travel (no load) with a minimum amount of handle
strokes. Once the cylinder contacts the load, the pump automatically shifts into the high pressure stage to lift the load.
P19
P59
P59F
700 bar• Rugged all metal construction for strength and
durability that won't burn through in weldingenvironments.
• two-speed feature reduces handle strokes soyou work faster and easier.
• Heavy-duty, formed metal handle provides lessflex, and less operator fatigue than round orcomposite handles.
• Convenient fill port allows pumps to be filled ina horizontal or vertical position.
• Relief valve inboard of check valve preventsloads from drifting down.
• Large valve knob gives added control forslowly metering loads down.
DIMENSIONS (MM)
ORDERING INFORMATION
See current price list for shipping weights.
Single-Acting
Cylinders
(Pumpincludes2-WayValve)
For Use With
OrderNo.
Volume & Pressure
Speed
Volume per Stroke (cu.cm.)
LP HP
MaximumPressure (bar)
LP HP
HandleEffort(kg)
Reservoir
OilCapacity(cu. cm.)
Usable OilCapacity(cu. cm.)
ProductWeight
(kg)OilPort
10.9 2.6
9.0 2.1
22.4 700 7.8
6.4
2P59
5.0 1.2 22.4 700 328 3.0400.244.92P19
P59F
3⁄8" NPTF
3⁄8" NPTF
3⁄8" NPTF54.5
LP = Low PressureHP = High Pressure
2 22.4 700
65.8 902
902
738
738
E M
DNA/BC
J
GF
H
G L
K dia.
Hoses, Fittings& GaugesPages74-80
Cylinder/PumpSpeed/SelectionChart Page178
Pump/CylinderSetsPage25
Power Team hand pumps,with the angled fill port,have a built in “relief valve”protection system. Thissystem is designed toprotect over-pressurizationof the reservoir fromsudden back pressure. Thissystem also works as a sealto prevent oil leaks.
Choosing TheRight PumpPages181-184
PumpNo. A B C D E F G H J K L M N P
P19 139.7 371.5 73.0 115.9 347.7 101.6 82.6 281.0 53° 7.9 101.6 3⁄8 NPTF 35.7 —
P59 177.8 533.4 88.9 127.0 584.2 108.0 82.6 501.7 38° 7.9 120.7 3⁄8 NPTF 41.3 —
P59F 88.9 425.5 88.9 152.4 590.6 108.0 82.6 514.4 — 7.9 114.3 3⁄8 NPTF 42.9 —
PumpAccessoriesPages161-165
®
24 www.powerteam.com
PUM
PS
Hydraulic Hand PumpsTwo-speed / Single- and Double-Acting
Reservoir capacity 9.5 liters.Hand operated pumps with large capacity reservoirs.
P157/P159
P300
• Rugged all metal construction for strengthand durability that won't burn thru in weldingenvironments.
• Two-speed feature reduces handles strokes soyou work faster and easier.
• Carry handles on all models.• Convenient fill port allows pumps (except
P300 & P460) to be filled in a horizontal orvertical position.
• Fill cap seal acts as safety valve (except P300)to prevent over-pressurizing of reservoir.
• Larger reservoir capacities to accommodatemultiple or high tonnage cylinders.
700 bar
DIMENSIONS (MM)
ORDERING INFORMATION
See current price list for shipping weights.
P157/P159
Single-Acting
Cylinders(Pump
includes 2-Way Valve)
Double-Acting
Cylinders(Pump
includes 4-Way Valve)
For Use With
OrderNo.
Volume & Pressure
Speed
Volume per Stroke (cu.cm.)
LP HP
MaximumPressure (bar)
LP HP
HandleEffort(kg)
Reservoir
OilCapacity(cu. cm.)
Usable OilCapacity(cu. cm.)
ProductWeight
(kg)OilPort
42.6 2.6
10.7 2.6
42.6 2.6
120.5 4.6
10.7 2.6
120.5 4.6
97 700
97 700
63.5
40.8
63.5
40.8
2245
5081
7539
2245
5081
7539
11.8
25.1
24.9
13.1
12.7
25.9
26.3
2491
5.7 liters
9.5 liters
2491
5.7 liters
9.5 liters
P157
P159
P300
P460
P157D
P159D
P300D
P460D
2
LP = Low Pressure HP = High Pressure
42.6 2.6
42.6 2.6
2
2
2
2
2
2
2
22 700
22 700
22 700
22 700
22 700
22 700
63.5
63.5
63.5
63.5
2491
2491 2245
2245 11.8
190.5
76.2
3⁄8" NPTF3⁄8" NPTF3⁄8" NPTF3⁄8" NPTF3⁄8" NPTF3⁄8" NPTF3⁄8" NPTF3⁄8" NPTF
P460
E M
DNA/BC
J
GF
H
G L
K dia.
+
K
G
PM
D
EF
H
A/BC
Hoses, Fittings& GaugesPages74-80
Cylinder/PumpSpeed/SelectionChart Page178
Pump/CylinderSetsPage25
Choosing TheRight PumpPages181-184
PumpNo. A B C D E F G H J K L M N P
197 521 123.8 175 578 98.4 76.2 502 39° 7.9 95.3 3⁄8 NPTF 57.2 —
P300 210 533 114.3 175 575 215.9 526 39° 7.9 95.3 3⁄8 NPTF 57.2 —
P460 283 787 171.5 289 610 743 279.4 229 80° 241.3 — 3⁄8 NPTF — 1⁄4 NPTF
PumpAccessoriesPages161-165
P300 hand pump and 10 ton cylinders used fora vehicle lift.
®
25www.powerteam.com
PUMPS
Hydraulic Cylinder And Pump Sets
Popular precision-matched cylinder and pump combinations packaged under one convenient order number.
• Precision-matchedhydraulic components todo the job safely andefficiently.
• Four styles of cylindersto choose from.
• Sets feature single- ortwo-speed hydraulichand pumps.
• Cylinders of varioustonnages with long,medium or short stroke.
• Each set includes thenecessary fittings,coupler and 1.8 m hose.
• Gauge and gaugemounting adapter isrecommended, butoptional. See pages 76-77.
* Based on 50% of the strokes being made at low-pressure and 50% of the strokes at high pressure.**Add suffix “B” (example: RPS102B, RPS203HB, etc.) to order set with optional storage box shown above and on page 161.
ORDERING INFORMATION See current price list for shipping weights
RPS55
700 bar
RPS203H
RPS1006
350722-Optional Storage Box
“C” Series CylindersHandle Strokes
Style Cyl. Retracted Required to Prod.of Cap. Stroke Order Height Fully Extended Cyl. Pump Hose Coupler Pump Wt.
Cyl. (tons) (mm) No. (mm) Cylinder No. No. No. No. Speed (kg)5 133.4 RPS55 216 75 C55C P12 9756 9798 Single 5.410 54.0 RPS102** 121 32 C102C P55 9756 9798 Single 11.810 155.6 RPS106** 248 93 C106C P55 9756 9798 Single 14.510 257.2 RPS1010** 349 154 C1010C P55 9756 9798 Single 16.1
“C” 15 104.8 RPS154** 200 81 C154C P55 9756 9798 Single 13.1Series 15 155.6 RPS156** 271 118 C156C P55 9756 9798 Single 15.4Cyl. 25 158.8 RPS256** 273 219 C256C P55 9756 9798 Single 19.3
25 362.0 RPS2514** 476 285* C2514C P159 9756 9798 Two 28.455 158.8 RPS556** 283 268* C556C P159 9756 9798 Two 37.5100 168.3 RPS1006 337 428* C1006C P460 9756 9798 Two 58.3
“Shorty” Cylinders“Shorty” 30 61.9 RPS302** 117 61* RSS302 P59 9756 9798 Two 18.1
Cyl. 50 60.3 RPS552** 127 89* RSS502 P59 9756 9798 Two 22.7100 57.2 RPS1002** 140 172* RSS1002 P59 9756 9798 Two 36.7
“Center-Hole” Cylinders“Center-
Hole” 20 76.2 RPS203H** 154 80 RH203 P55 9756 9798 Single 18.3Cyl.
Aluminum Jacking CylindersAlum. 55 155.6 RPS556A** 273 262* RA556 P159 9756 9798 Two 21.3
®
26 www.powerteam.com
PUM
PS
Air Hydraulic Pumps98.4 cu. cm./min., Single-Acting (PA6 Series)
Single-speed pump designed to drive single-acting cylinders or tools. Pump can easily beoperated by hand or foot. Generally recommended for tools and cylinders up to 15 ton.
PA6PA6M-1
• Single-speed pumps designed to drive single-actingcylinders, are compact, lightweight and portable.
• A quarter century record of proven reliability. Thepower unit of choice for major manufacturers of autobody, frame straighteners and other equipment.
• Operate at 3-8 bar shop air pressure at the pump.• Internal relief valves protect circuit components, air inlet
filter protects motor.
• All metal air motor, ductile iron pump. Serviceablepump motor is not a “throw away”, providingeconomical repair.
• Permanently vented reservoir cap.• An inexpensive alternative to using manually operated
pumps.• Metal reservoir conversion kits and
filters/regulators/lubricators found in accessoriessection. See pages 161-165.
• dBA 85 at 700 bar for all PA6 Series pumps.
700 bar
PA6-2
Typical Set-upHook-up for single-acting cylinders
AIRPUMP
OIL
PERFORMANCE
Hoses, Fittings& GaugesPages74-80
Cylinder/PumpSpeed/SelectionChart Page178
PumpAccessoriesPages161-165
Choosing TheRight PumpPages181-184
®
27www.powerteam.com
PUMPS
Base model pump with high density polyethylene reservoir.
PA6 with externally adjustable relief valve.
PA6A with metal reservoir.
PA6, except has metal reservoir.
PA6 with 3.7 meter remote control.
PA6R except has metal reservoir.
PA6, except has 3.8 liter metal reservoir.
PA6, except has 7.6 liter, high density polyethylene reservoir.
PA6, except has 9.5 liter metal reservoir.
OrderNo. Oil Port
Reservoir (liters)Air SupplyReq’d (bar) Cap. Usable
Prod. Wt. (kg)
PA6 3 - 8 1.7 1.6 3⁄8" NPTF 6.3
PA6A 6.8
PA6M 8.2
PA6M-2 9.5 9.1 14.5
ORDERING INFORMATION
See current price list for shipping weights.
PA6M-1 10.73.8 3.0
PA6-2 11.17.6 7.3
3⁄8" NPTF
3⁄8" NPTF
3⁄8" NPTF
3⁄8" NPTF
3⁄8" NPTF
3 - 8
3 - 8
3 - 8
3 - 8
3 - 8
1.7
1.7
1.6
1.6
PA6AM 7.73⁄8" NPTF3 - 8 1.7 1.6
PA6R 9.31.7 1.6
PA6RM 9.81.7 1.6
3⁄8" NPTF
3⁄8" NPTF
3 - 8
3 - 8
Description
GD
B
A
C
E G
DIMENSIONS (MM)
PumpNo. A B C D E G
PA6 197 149 111 241 127 102 x 229
PA6A 197 149 111 241 127 102 x 229
PA6AM 197 149 111 241 127 102 x 229
PA6M 197 149 111 241 127 102 x 229
PA6R 197 149 111 241 127 102 x 229
PA6RM 197 149 111 241 127 102 x 229
PA6M-1 200 152 111 321 187 none
PA6M-2 254 197 171 292 241 203 x 254
PA6-2 260 203 178 292 241 130 x 181
®
28 www.powerteam.com
PUM
PS
Air Hydraulic Pumps98.4 cu. cm./min., Double-Acting (PA6D Series)
Single-speed pump designed to drive double-acting cylinders.Generally recommended for tools or cylinders up to 15 ton.
PA6DPA6DM-1
700 bar
PA6D2
• Compact, lightweight and portable single-speed pumpfor driving double-acting cylinders.
• A quarter century record of proven reliability. Thepower unit of choice for major manufacturers of autobody and frame straighteners and other equipment.
• Operate at 3-8 bar shop air pressure at the pump.• Internal relief valves protect circuit components, air
inlet filter protects motor.• All metal air motor, ductile iron pump. Serviceable
pump motor is not a “throw away”, providingeconomical repair.
• Permanently vented reservoir cap.• An inexpensive alternative to using manually operated
pumps.• Metal reservoir conversion kits and
filters/regulators/lubricators found in accessoriessection. See pages 161-165.
• Four reservoir sizes available to best match yourapplication.
• Four reservoir sizes available to best match yourapplication.
• dBA 85 at 700 bar for all PA6 pumps.
Typical Set-upHook-up for double-acting cylinders
AIRPUMP
OIL
OIL
PERFORMANCE
Hoses, Fittings& GaugesPages74-80
Cylinder/PumpSpeed/SelectionChart Page178
PumpAccessoriesPages161-165
Choosing TheRight PumpPages181-184
Base model pump with high density polyethylene reservoir.
PA6D, except has metal reservoir.
PA6D, except has 3.8 liter metal reservoir.
PA6D, except has 7.6 liter, high density polyethylene reservoir.
PA6D, except has 9.5 liter metal reservoir.
®
29www.powerteam.com
PUMPS
OrderNo. Valve No. Oil Port
Reservoir (liters)Air SupplyReq’d (bar) Cap. Usable
Prod. Wt. (kg)
PA6D 9504, 3-way/4-way 3 - 8 1.7 1.6 3⁄8" NPTF 8.3
PA6DM 9.2
PA6D2 13.0
9504, 3-way/4-way
9504, 3-way/4-way
3⁄8" NPTF
3⁄8" NPTF
3 - 8
3 - 8
1.7
7.6
1.6
7.3
PA6DM-1 12.79504, 3-way/4-way
3⁄8" NPTF3 - 8 3.8 3.0
PA6DM-2 16.49.5 9.19504, 3-way/4-way
3⁄8" NPTF3 - 8
Description
ORDERING INFORMATION
See current price list for shipping weights.
A
C
GD
B
GE
DIMENSIONS (MM)
PumpNo. A B C D E G
PA6D 264 149 111 241 127 102 x 229
PA6DM 264 149 111 241 127 102 x 229
PA6DM-1 279 146 111 321 187 none
PA6D2 324 203 178 287 235 130 x 181
PA6DM-2 318 197 171 292 241 203 x 254
PA6D pump, DG100digital pressuregauge and 25 toncylinder used in atest fixture.
®
30 www.powerteam.com
PUM
PS
Air Hydraulic Pumps147.6 cu. cm./min., Single-Acting (PA9 Series)
Single-speed pump designed to drive single-speed cylinders or tools. Pump can bemounted vertically or horizontally. Ideal for operating portable hydraulic tools.
PA9Foot Control
PA9HHand Control
700 bar
PERFORMANCE
Pressure vs volume based on 7 bar airpressure:
• PA9 series single-speed pumps are ideal for poweringsingle-acting cylinders and portable hydraulic tools.
• Easier to operate than a hand pump, giving you thespeed you need at an affordable price.
• A time-tested design constructed totally of metal (notplastic!) for years of dependable on the job service.
• Easy and economical to service; not a “throw away”unit.
• Unique bladder design for all-position operation andstorage.
• Operates on 3-8 bar shop air, at 3.8 liters/min.• Heavy-duty, hard-coat anodized aluminum housing,
distinctive styling.• Oil filler with integral safety relief minimizes chance of
damage to reservoir bladder if overfilling occurs.
Typical Set-upHook-up for single-acting cylinders
AIRPUMP
OIL
Hoses, Fittings& GaugesPages74-80
Cylinder/PumpSpeed/SelectionChart Page178
PumpAccessoriesPages161-165
Choosing TheRight PumpPages181-184
®
31www.powerteam.com
PUMPS
PA9
PA9H
For Use with Air Supply Max. Pressure Prod. Cyl. Type Req’d Cap. Usable Oil Port Output Weight
ORDERING INFORMATION
See current price list for shipping weights.
Single-Acting
OrderNo.
Reservoir
3 - 8 bar 574 cu. cm. 549 cu. cm. 3⁄8" NPTF 700 bar 6.8 kg
3 - 8 bar 574 cu. cm. 549 cu. cm. 3⁄8" NPTF 700 bar 6.8 kgSingle-Acting
WARNING
A
B C
E
F
DK
I
Hup position
GJ
Relief valve settings: up to 700 barMounting holes (standard): 9.7 mm slots
Turn and hold to releasehydraulic pressure on PA9H
Press and hold to run motor on PA9H
DIMENSIONS (MM)
PumpNo. A B C D E F G H I J K
PA9 432 305 71.4 108 149 178 142 178 28.2 – –
PA9H 432 305 71.4 108 — 178 — 178 28.2 122 170
®
32 www.powerteam.com
PUM
PS
Air Hydraulic Pumps98.4 cu. cm./min. – Two-speed (PA60 Series)
Similar to PA6 for performance with two-speed feature to rapidly advance cylinder or tool tothe work.
PA64
700 bar
• Two-speed pump for rapid oil delivery at low pressureto quickly advance cylinder or tool.
• Second speed produces high pressure to produce forcenecessary to complete work.
• Equipped with air pressure regulator, air filter andlubricator.
• Serviceable air motor (not a throw-away) foreconomical repair.
• Internal relief valves to protect circuit components.• Permanently vented reservoir cap.
PERFORMANCE
AIRPA60
OIL
OIL
Single-actingcylinder.
9510 subplatewith 9502, 9505or 9576 valve.
In this typicalapplication anair/hydraulic pumpis used with a remotevalve to drive asingle-acting cylinder.
Typical Set-up
PA60
Hoses, Fittings& GaugesPages74-80
Cylinder/PumpSpeed/SelectionChart Page178
Choosing TheRight PumpPages181-184
PumpAccessoriesPages161-165
®
33www.powerteam.com
PUMPS
For use with remote valves.
For use with single- or double-acting cylinders.
OrderNo. Valve No. Oil Port
Reservoir (liter)Air SupplyReq’d (bar) Cap. Usable
Prod. Wt. (kg)
PA60 Manifold 3 - 8 7.6 6.8 3⁄8" NPTF 24.5
PA64 25.4
NOTE: Air inlet port 1⁄4" NPTF.
SINGLE- & DOUBLE-ACTING
9507, 3 way/4-way
3⁄8" NPTF3 - 8 7.6 6.8
Description
ORDERING INFORMATION
Requires .56 cu. m/min. at 7 bar shop air pressure at the pump.
SPECIFICATIONS AND DIMENSIONS
Dimensions (mm) Oil Del.* (liters/min. @)
PA60 – 240 206 362 181 0.10
Pump No. A B C D E F G
Max.PressureOutput(bar)
0bar
7bar
70bar
700bar
PA64 362 – 206 362 244 181 130 0.10
5.60 0.80 0.196.24700
350bar
244 130
700 5.60 0.80 0.196.24
A
C
F
B
D
E
G
* Typical delivery. Actual flow will vary with field conditions.
ValveFunction
–
AdvanceHold Return
®
34 www.powerteam.com
PUM
PS
Air Hydraulic Pumps459.2 cu. cm./min. — “low pressure” (PA50 Series)
Designed to operate low pressure (220 bar) systems, single-speed.Pump models available to drive single-acting or single- and double-acting systems.
PA50D
PA50R2
220 bar
PERFORMANCE
• Single-speed, low pressure (220 bar) output pumps.• All metal air motor for long dependable service.• Serviceable air motor (not a throw away) for
economical repair.
• Air inlet filter protects motor. Filter in outlet portprotects against contaminated systems.
• Standard or large reservoirs to suit your application'soil requirements.
Typical Set-upHook-up for single-acting cylinders
AIRPUMP
OIL
PA50M
Hoses, Fittings& GaugesPages74-80
Cylinder/PumpSpeed/SelectionChart Page178
PumpAccessoriesPages161-165
Choosing TheRight PumpPages181-184
®
35www.powerteam.com
PUMPS
PA50, except designed to operate either single- or double-actingsystems. Valve function: Advance / Return.
OrderNo. Valve No. Oil Port
Reservoir (liters)Air SupplyReq’d (bar) Cap. Usable
Prod. Wt. (kg)
PA50D9504,3-way/4-way
3 - 8 1.7 1.6 3⁄8" NPTF 8.3
NOTE: Air inlet port 1⁄4" NPTF.
SINGLE- AND DOUBLE-ACTING
Description
Base model pump with high density polyethylene reservoir.
PA50, except has metal reservoir.
PA50, except has 3.7 meter remote control.
PA50R, except has metal reservoir.
PA50R, except has 7.6 liter reservoir.
OrderNo. Valve No. Oil Port
Reservoir (liters)Air SupplyReq’d (bar) Cap. Usable
Prod. Wt. (kg)
PA50 – 3 - 8 1.7 1.6 3⁄8" NPTF 6.4
PA50M 7.3
PA50RM 9.3
NOTE: Air inlet port 1⁄4" NPTF.
SINGLE-ACTING
–
–
3⁄8" NPTF
3⁄8" NPTF
3 - 8
3 - 8
1.7
1.7
1.6
1.6
PA50R 8.4– 3⁄8" NPTF3 - 8 1.7 1.6
PA50R2 12.97.6 7.3– 3⁄8" NPTF3 - 8
Description
SPECIFICATIONS AND DIMENSIONS
Dimensions (mm) Oil Del.* (liters/min. @)
PA50, PA50R,PA50M, PA50RM 197 149 111 241 – –
Pump No. A B C D E F G
Max.PressureOutput(bar)
0bar
7bar
70bar
700bar
PA50R2 260 203 178 292 241 – 130 x 181 –
PA50D 264 149 111 241 127 229 102 –
1.76 1.41 0.45†2.05220
350 bar
127 102 x 229
220
220
1.76 1.41 0.45†2.05
1.76 1.41 0.45†2.05
ORDERING INFORMATION
Requires .56 cu. m/min. at 7 bar shop air pressure at the pump.
A
C
F
B
D
E
G
GD
B
A
C
E G
PA50, PA50M, PA50R, PA50RM,PA50R2
PA50D
* Typical delivery. Actual flow will vary with field conditions.† PA50 Series measured at 220 bar.
®
36 www.powerteam.com
PUM
PS
Air Hydraulic Pumps278.8 cu. cm./min. — Two-speed (PA17 Series)
Two-speed pump with rotary-style air motor. Generally recommended for cylinders up to 50 ton capacity.
• Use where air is preferred source of energy, whereelectricity is unavailable or sparks are a concern.
• Two-speed operation for high speed cylinder advance.
• Durable 7.6 liter thermoplastic reservoir. (Metalreservoir conversion kits are available.)
• Features air motor capable of starting under full load.
PERFORMANCETypical Set-up
Hook-up for single-acting cylindersTypical Set-up
Hook-up for double-acting cylinders
AIR
PUMP OIL
AIR
PUMP
OIL
OIL
PA174
Hoses, Fittings& GaugesPages74-80
Cylinder/PumpSpeed/SelectionChart Page178
700 bar
PA172
Choosing TheRight PumpPages181-184
PumpAccessoriesPages161-165
®
37www.powerteam.com
PUMPS
D
A
EB
FC
H
SPECIFICATIONS AND DIMENSIONS
Dimensions (mm) Oil Del.* (liters/min. @)
PA172 359 289 235 178 130 0.3
Pump No. A B C D E F H
Max.PressureOutput(bar)
0bar
7bar
70bar
700bar
PA174 359 289 235 178 181 130 3⁄8 " NPTF 0.3
3.8 0.4 0.44.6700
350bar
181 3⁄8 " NPTF
700 3.8 0.4 0.44.6
Base model pump with 7.6 liter thermoplasticreservoir.
OrderNo. Valve No.
Reservoir (liters)Air SupplyReq’d (bar) Cap. Usable
Prod. Wt. (kg)
PA172 9517, 2-Way 3 - 8 7.6 4.7 18.1
Description
ORDERING INFORMATION
Requires .56 cu. m/min. at 6 bar shop air pressure at the pump. dBA 85/90 at 700 bar.
SINGLE-ACTING
PA172, except has 9500 valve for use with single- ordouble-acting cylinders.
OrderNo. Valve No.
Reservoir (liters)Air SupplyReq’d (bar) Cap. Usable
Prod. Wt. (kg)
PA174 9500, 4-way 3 - 8 7.6 4.7 18.6
Description
SINGLE- & DOUBLE-ACTING
* Holds pressure in advance position when valve motor is shut off, in return position with motor running. Pump will build pressure when motor is shut off, oilreturns to reservoir.
ValveFunction
Advance/Return*
ValveFunction
Advance HoldReturn*
* Typical delivery. Actual flow will vary with field conditions.
®
38 www.powerteam.com
PUM
PS
Air Hydraulic Pumps754-902 cu. cm./min. — Two-speed (PA46 & PA55 Series)
Two-speed pump with rotary-style air motor. Generally recommended for cylinders up to150 ton capacity.
PA464R
700 bar
• Use where air is the preferred sourceof energy.
• Features 2.24 kW motor capable ofstarting under full load.
• Two-speed operation for high speedcylinder advance.
• Models available with full remotecontrol over advance and return,except for PA554.
• Tandem center valve holds the loadwhen pump is shut off.
PERFORMANCE
Typical Set-upHook-up for single-acting cylinders
Typical Set-upHook-up for double-acting cylinders
AIR
PUMP
OIL
OIL
AIR
PUMP OIL
PA554PA462
Hoses, Fittings& GaugesPages74-80
Cylinder/PumpSpeed/SelectionChart Page178
PumpAccessoriesPages161-165
Choosing TheRight PumpPages181-184
PA554 pump and RH2008 Center Holecylinder used to tension cables.
PA464R 381 292 241 178 203 0.7
PA464RA 381 292 241 178 254 203 3⁄8" NPTF 0.7
7.2 0.8 0.87.4700254 3⁄8" NPTF
700 7.2 0.8 0.87.4
* Holds when motor is shut-off and valve is in “advance” position.† The PA464RA has an “automatic dump” feature. Pressure is not held when operator releases “advance” or
“return” button. PA464R will “hold” only in the “advance” position with the motor shut off.∞ Not to be used for lifting.
®
39www.powerteam.com
PUMPS
Base model pump with 9.5 liter steel reservoir.
OrderNo. Valve No.
Reservoir (liters)Air SupplyReq’d (bar) Cap. Usable
Prod. Wt. (kg)
PA462 9584, 2-way 3 - 8 9.5 9.4 27.2
Description
ORDERING INFORMATION
Requires 1.4 cu. m/min. at 6 bar shop air pressure at the pump. dBA 85/90 at 700 bar.
SINGLE-ACTING
PA462, except has 9500 valve capable of running 2 single-acting cylinders or one double-acting cylinder.
PA462 with air actuated valve for full remote control overadvance and return. Includes 3.7 meter remote control.
PA464R except, has automatic dump feature. 7.6 meterremote control.
OrderNo. Valve No.
Reservoir (liters)Air SupplyReq’d (bar) Cap. Usable
Prod. Wt. (kg)
PA464 9500, 4-way 3 - 8 9.5 9.4 27.6
Description
SINGLE- & DOUBLE-ACTING
PA464R† 9594 4-way 3 - 8 9.5 9.4 35.3
PA464RA∞† 9594, 4-way 3 - 8 9.5 9.4 35.8
SPECIFICATIONS AND DIMENSIONS
Dimensions (mm) Oil Del.* (liters/min. @)
PA462 381 292 241 178 203 0.7
Pump No. A B C D E F H
Max.PressureOutput(bar)
0bar
7bar
70bar
700bar
PA464 381 292 241 178 254 203 3⁄8" NPTF 0.7
7.2 0.8 0.87.4700
350bar
254 3⁄8" NPTF
700 7.2 0.8 0.87.4
* Typical delivery. Actual flow will vary with field conditions.NOTE: Four mounting holes 1⁄2 in.-20.
D
A
EB
FC
H
ValveFunction
Advance /Hold / Return
ValveFunction
Advance / Hold /Return*
Advance / Hold /Return
Advance / Hold /Return*
PA554 483 292 241 178 254 203 3⁄8" NPTF 0.9700 7.2 1.3 1.17.4
High performance pump with 9.5 liter steel reservoir. PA554 9500, 4-way 3 - 8 9.5 8.4 22.2Advance / Hold /
Return*
®
40 www.powerteam.com
PUM
PS
Electric/Battery Hydraulic Pumps164 cu. cm./min. – .19 kW (PE10 & PR10 Series)
Two-speed high performance in compact package. Electric and battery powered modelsexcellent for powering tools and generally recommended for cylinders up to 25 ton.
700 bar
• The Quarter Horse® is a perfect portable power sourcefor hydraulic cylinders, spreaders, punches, nutsplitters, pipe flange spreaders and other tools. Pumpw/oil weighs just 9.1 kg.
• Powered by a .19 kW, 6,000 rpm, permanent magnetmotor that starts easily under load, even with reducedvoltage conditions.
• Pumps for 200 and 350 bar operating pressures alsoavailable: consult factory.
• Battery-operated models have 2.4 meter power cordwith alligator clips to connect to any 12 volt battery.
• Optional rechargeable battery pack with shoulder strapfor maximum portability.
• Pump typically delivers 15 minutes of continuousoperation at 700 bar on a single battery.
• Bladder type reservoir (1 liter usable) enables pump tobe operated in any position.
• The optional, externally-adjustable pressure regulatorcan be easily installed on all pumps.
• Optional 24 volt hand and foot switches available for allAC powered pump models.
• High-impact housing with flame-retardant construction. • Base mounting holes for fixed installations if desired.
PERFORMANCE
The Quarter Horse pumphas a maximum operatingpressure of 700 bar,which handles a widevariety of hand heldhydraulic tools.
PE102
PR102A
PR104
LR19814
Hoses, Fittings& GaugesPages74-80
Cylinder/PumpSpeed/SelectionChart Page178
Choosing TheRight PumpPages181-184
4-Way
Auto.Dump
Auto.Dump
Auto.Dump
®
41www.powerteam.com
PUMPS
* “Advance” position holds pressure with motor shut off. “Return” position advances cylinder with motor running and returns cylinder with motor shut off.** Cylinder advances with motor running and automatically returns with motor shut off.† Comes with an 2.4 m alligator clip cord for 12 volt DC use.
PE102-220
PR102
AdvanceReturn (Auto.)*
AdvanceReturn**Advance
Return(Auto.)*AdvanceReturn
AdvanceReturn(Auto.)*
AdvanceReturn**
2–Way/Auto.DumpPE102
PE102A
PE102A-220
PR102A
.19 kW, 110/115V50/60 Hz, Single Phase
(1 literusable)
.19 kW, 220/230V50/60 Hz, Single Phase
.19 kW, 12V †
2–Way/Auto.Dump
2–Way/Auto.Dump
Rocker Type off,Momentary on9561
9562
9561
9562
9561
9562
ORDERING INFORMATION
See current price list for shipping weights.
SINGLE-ACTING
Oil Delivery(liters./min.)
Pump No.
Max.PressureOutput
dBa atidle and
700bar
0-30bar
700bar
OverallDimensions
(mm)
Prod.Weightwith Oil
(kg)
PE10 SeriesPR10 Series
700bar 68–74* 1.9 0.16 330L x 197W
x 203 9.1
SPECIFICATIONS AND DIMENSIONS
* Measured at 0.9 meter distance, all sides.NOTE: PR10 rechargeable model is equipped with 2.4 meter cord with
alligator clips. Order optional battery pack (No. BP12VQ) or usewith any 12 volt battery.
NOTE: High pressure flow on 350 bar unit is .32 L/min. Flow on 200 barunit is .48 L./min. Consult factory for further information.
NOTE: Amp draw at 700 bar; 6 amp at 115 volt, 3 amp at 230 volt, and 25amp at 12 volt.
Rocker Type off,Momentary on
Rocker Type off,Momentary on
Rocker Type off,Momentary on
Rocker Type off,Momentary on
Rocker Type off,Momentary on
.19 kW, 110/115V50/60 Hz, Single Phase
.19 kW, 220/230V50/60 Hz, Single Phase
.19 kW, 12V †
(1 literusable)(1 literusable)(1 literusable)(1 literusable)(1 literusable)
Order Valve Control Reservoir Description No. Type No. Function Switch Motor Cap.
DOUBLE-ACTING
PR104
AdvanceHold Return
AdvanceHold Return
AdvanceHold Return
4-WayPE104
PE104-220
(1 literusable)
4–Way
Rocker Type off,Momentary on9563
9563
9563
Rocker Type off,Momentary on
Rocker Type off,Momentary on
(1 literusable)(1 literusable)
Order Valve Control Reservoir Description No. Type No. Function Switch Motor Cap.
.19 kW, 110/115V50/60 Hz, Single Phase
.19 kW, 12V †
.19 kW, 220/230V50/60 Hz, Single Phase
RC12V – Replacement 1.2 mbattery cord only. Wt., 0.2 kg.
Battery Charger Only – Willrecharge RB12V battery in4 hrs. See below for part no.BC212 – Battery charger forU.S.A. Wt., 3 kg.BC212EUR – Battery chargerfor Europe. Wt., 3 kg.25017 – Remote hand controlwith 3 m cord. Wt., 0.4 kg
ACCESSORIES
RB12V
RC12V
BP12VQ – Optional 12 voltbattery pack. Includes sealedlead acid battery, 115Vcharger, 1.2 m cord, carryingcase and shoulder strap.Wt., 8 kg.
251660 – Foot switch with 3m cord. Single pole, doublethrow, 15 amp @ 125-250VAC. Wt., 0.45 kg.
BP12INT – Battery with cordand carrying case. Wt., 5 kg.RB12V – Replacement batteryonly. Wt., 4.7 kg.
9560 –Pressureregulator.Adjustablefrom 70 to700 bar. All mountinghardware included. Wt., 1.4 kg.
Base model pump with .19 kW motor.Bladder type reservoir, 110 volt power req.
PE102, except has automatic pump valve.
PE102, except requires 220 volt.
PE102A, except requires 220 volt.
PE102, except requires 12 volt DC.
PE102A, except requires 12 volt DC.
Base model pump has 4-way valve for operatingdouble-acting systems. 110 volt power required.
PE104, except requires 220 volt.
PE104, except requires 12 volt DC.
®
42 www.powerteam.com
PUM
PS
Electric Hydraulic Pumps278.8 cu. cm./min. — .37 kW (PE17 Series)
Two-speed high performance at a low price. Ideal for maintenance and constructionapplications where low voltage is a concern. Generally recommended for cylinders up to55 ton.
700 bar
• For use with single-acting or double-acting cylinders atoperating pressures to 700 bar.
• PE17 series is for intermittent duty; starts under full load.• Equipped with .37 kW, 2,874 rpm, single-phase, thermal
protected induction motor; 3 meter remote control cord(PE172S-50-220 has 7.6 meter cord).
• Low amperage draw; small generators and low amperagecircuits can be used as power source.
• All have 7.6 L thermoplastic reservoir except PE172M,PE172AM, PE172SM and PE174M which have 9.5 L metalreservoir. Optional steel reservoirs also available. Order part#213895
• Extremely quiet with noise level ranging from 67-81dBA.
Optional Steel ReservoirNo. 213895 — Steel reservoir for PE172, PE172A, PE172S andPE174. Includes gasket and fasteners.
•IMPORTANT: Oil temperatures in excess of 65.5˚ C. may causepermanent failure of the thermoplastic reservoir of PE17 seriespumps.
PERFORMANCE
A
B
E
DC F
G
PE172-50-220 PE174-50-220
PE172SM-50-220
LR19814
Hoses, Fittings& GaugesPages74-80
Cylinder/PumpSpeed/SelectionChart Page178
PumpAccessoriesPages161-165
Choosing TheRight PumpPages181-184
Max. dBA at Amp Draw Dimensions (mm) Prod. Wt.Press. Idle and 220 V - at 0 7 350 700 With Oil
Pump No. Output rpm 700 bar 700 bar bar bar bar bar A B C D E F G (kg)PE17 Series 700 bar 2,874 67/81* 5 3.9 2.5 0.3 0.2 470 178 289 181 378 235 130 20.4PE17M Series 700 bar 2,874 67/81* 5 3.9 2.5 0.3 0.2 460 168 292 N/A 368 241 N/A 24.0PE17-E220 700 bar 2,874 67/81* 5 3.9 2.5 0.3 0.2 460 168 292 N/A 368 241 N/A 24.0 PE17M-E220 700 bar 2,874 67/81* 5 3.9 2.5 0.3 0.2 460 168 292 N/A 368 241 N/A 24.0
* Measured at 0.9 meter distance, all sides. † Typical delivery. Actual flow will vary with field conditions.
SPECIFICATIONS AND DIMENSIONS
Oil Del. (liters./min. @)†
4.72 liters
Base model pump has .37 kW pump with 7.6liter thermoplastic reservoir.PE172-50-220, except has 9.5 L aluminumreservoir.
PE172-50-220, except has solenoid operatedvalve.PE172S-50-220, except has aluminumreservoir.Best suited for crimping, punching, pressing.Not for lifting. Thermoplastic reservoir.
PE172A, except has aluminum reservoir.
.37 kW pump with 7.6 liter thermoplasticreservoir. Meets CE requirements.PE172-50-220, except has 9.5 liter aluminumreservoir. Meets CE requirements.PE172-50-220, except has solenoid operatedvalve. Meets CE requirements.PE172S-50-220, except has aluminumreservoir. Meets CE requirements.
Best suited for crimping, punching, pressing.Thermoplastic res. Meets CE requirements.PE172A, except has aluminum reservoir.Meets CE requirements.
Advance Return(Auto†)
Advance HoldReturn
®
43www.powerteam.com
PUMPS
‡ Some Power Team pumps are available inspecial configurations not listed in this catalog.Power Team can “Assemble to Order” pumpswith special seals, voltages, valves, relief valvesettings, etc. For your special requirementsplease consult your local distributor or the PowerTeam factory.
ValveType No. Function
Reservoir(Usable)Motor
ControlSwitch ††
OrderNo.
* Available with 115 V., 60 Hz motor (to order, remove suffix “50-220” from pump order number).** “Advance” position holds pressure with motor shut off.† “Advance” position holds pressure with motor shut off. “Return” position advances cylinder with motor
running and returns cylinder with motor shut off.†† Control switch on PE17 series wired with line voltage.∞ Not to be used for lifting.(1) These pumps are marked for meeting the requirements of 89/366/EEC and 73/23/EEC. In addition,
they meet the European Union Machinery Directive and are furnished with a Declaration of Incorporation.For additional information contact your nearest Power Team facility.
NOTE: The remote motor control switch on 220V., 50 cycle PE17 series pumps is 24 volt.NOTE: Usable oil is calculated with the oil fill at the recommended level of 38 mm below reservoir cover
plate.
ORDERING INFORMATION ‡
See current price list for shipping weights.
SINGLE-ACTING
PE172-50-220 2-Way 4.72 liters
PE172M-50-220 6 liters
PE172S-50-220 3-Way 4.72 liters
PE172SM-50-220 6 liters
9517
9570
2-Way
3-Way 9570
9517
Advance Return(Auto†)
Advance HoldReturn
Advance Return
PE172A-50-220∞ Advance Return 4.72 liters
PE172AM-50-220∞
PE172-E220
PE172M-E220
PE172S-E220
PE172SM-E220
PE172A-E220∞
PE172AM-E220∞
6 liters
45554Auto/DumpManifold
Auto/DumpManifold 45554
RemoteMotor Control (3.1 m) on/off
RemoteMotor Control (3.1 m) on/off
RemoteMotor & Valve
(7.6 m)
.37 kW 220 V*50 Hz, Single Phase
.37 kW 220 V*50 Hz, Single Phase
.37 kW 220 V*50 Hz, Single Phase
.37 kW 220 V*50 Hz, Single Phase
Advance Return(Auto†)
Advance HoldReturn
2-Way 4.72 liters
6 liters
3-Way
6 liters
9517
9570
2-Way
3-Way 9570
9517
Advance Return(Auto†)
Advance HoldReturn
Advance Return
Advance Return 4.72 liters
6 liters
45554Auto/DumpManifold
Auto/DumpManifold 45554
RemoteMotor Control (3.1 m) on/off
RemoteMotor Control (3.1 m) on/off
RemoteMotor & Valve
(3.1 m)
Description
MULTI SINGLE-ACTING
PE172-50-220, except has 9500 double-acting valve.
Same as PE174-50-220, except hasaluminum reservoir.
PE172-50-220, except has 9500 double-acting valve. Meets CE requirements.Same as PE174-50-220, except hasaluminum reservoir. Meets CE requirements.
Advance HoldReturn**
ValveType No. Function
Reservoir(Usable)Motor
ControlSwitch ††
OrderNo.
PE174-50-220 4-Way 4.72 liters
PE174M-50-220 6 liters
9500
4-Way 9500
Advance HoldReturn** Remote
Motor Control (3.1 m) on/off
Advance HoldReturn**
PE174-E220 4-Way 4.72 liters
PE174M-E220 6 liters
9500
4-Way 9500
Advance HoldReturn** Remote
Motor Control (3.1 m) on/off
Description
(1)
(1)
(1)
(1)
®
44 www.powerteam.com
PUM
PS
Electric Hydraulic Pumps295.2 cu. cm./min. — .37 kW (PE18 Vanguard Jr.® Series)
Vanguard Jr.® pumps are very light weight and compact. Ideal for maintenance andconstruction applications where low voltage is a concern. Generally recommended forcylinders up to 55 ton and small hydraulic tools.
700 bar
• Vanguard Jr.® pumps provide two-speed high performance ina light-weight, compact package.
• Ideal for use with small hydraulically powered tools.• For use with single- or double-acting cylinders at operating
pressures to 700 bar. • Gauge port provided on pump. Metal reservoir on all models.• Equipped with a .37 kW, 220 volt, 50 Hz single phase motor
that starts under load, even at reduced voltage.• Low amperage draw permits use with smaller generators and
low amperage circuits.• All pumps have a 3 meter remote control except PE183C-50-
220 which has a 7.6 meter remote control.
• CSA rated for intermittent duty. High noise level of 85-90dBA.
For operating hydraulic crimping, cutting or other tools:• No. PE183C-50-220 - For crimping or pressing applications.
Has special electrical circuitry to pulse/advance, hold at fullpressure, build to a predetermined pressure, release and resetcircuit. Features separate emergency return switch.
• No. PE184C-50-220 - Allows you to alternately operate aspring-return cutting and/or crimping tool withoutdisconnecting either tool. Select port connection with manual4-way valve, start pump with remote control hand switch andextend connected tool. When hand switch is switched to off,pump stops and automatic valve opens, allowing tool toreturn. In center (neutral) position, manual control valveholds tool in position at time valve is shifted.
DC Conversion Kit*
Order kit No. 205601 to convert PE18 series pumps from115/230 volt AC to 115/230 volt DC. Kit includes a heavy-dutyON/OFF switch for both AC and DC voltage hook-ups.* For use only with PE182, PE183, PE184 and PE184-2 when
no remote control is used.
PE182-50-220PE183-2-50-220
PE183C-50-220
PERFORMANCE
LR19814
Hoses, Fittings& GaugesPages74-80
Cylinder/PumpSpeed/SelectionChart Pages178
PumpAccessoriesPages161-165
Choosing TheRight PumpPages181-184
PE182-50-220PE183-50-220
PE183A-50-220PE184-50-220
®
45www.powerteam.com
PUMPS
G
F
D
C
B
A
SPECIFICATIONS AND DIMENSIONS
* 9.5 L reservoir. ** Measured at 0.9 meter distance, all sides.
† Typical delivery. Actual flow will vary with field conditions. †† Special application pumps for cutting, crimping or pressing.
Oil Del. (liters/min. @) † Dimensions (mm)
Pump No.
MaximumPressureOutput rpm
dBA at Idle &
700 bar
Amp Draw220V at700 bar
0bar
7bar
350bar
700bar A B C D F G
Prod.Weightwith Oil
(kg)
700 bar 12,000 85/90** 4.5 Amps 3.7 3.0 0.4 0.3 406 121 203 181 152 130 13.6
PE183-2-50-220*PE184-2-50-220* 470 184 292 254 241 203 19.0
PE183C-50-220 †† 406 121 203 181 152 130 13.6
PE184C-50-220 ††
700 bar 12,000 85/90** 4.5 Amps 3.7 3.0 0.4 0.3
700 bar 12,000 85/90** 4.5 Amps 3.7 3.0 0.4 0.3
700 bar 12,000 85/90** 4.5 Amps 3.7 3.0 0.4 0.3 406 121 203 181 152 130 13.6
Base model pump has .37 kW pumpwith 2-Way valve and 1.9 L reservoir.PE182-50-220, except has 3-wayvalve.PE18350-220, except has 7.6 Lreservoir.
PE183, except has “dump valve”.
Advance Hold Return
ValveType Function
Reservoir(Usable)Motor**
ControlSwitch ††
OrderNo.
ORDERING INFORMATION
See current price list for shipping weights.
SINGLE-ACTING
PE182-50-220 2-Way 1.7 liters
PE183-50-220 1.7 liters
PE183-250-220 8.4 liters††
3-Way
Advance Return†
Advance Hold Return
Remote Motor Control (3.1 m) on/off
.37 kW 220 volts
50/60 Hz A.C.,Single Phase
Description
3-Way
Remote Motor Control (3.1 m) on/off
Remote Control (3.1 m)
1.7 litersPE183A-50-220 ∞ Advance ReturnAuto/DumpPump
Remote (3.1 m)
DOUBLE-ACTING
Base model pump has .37 kW pump fordouble-acting systems with 1.9 L reservoir.
PE184, except with 7.6 L reservoir. Advance HoldReturn†
ValveType Function
Reservoir(Usable)Motor**
ControlSwitch ††
OrderNo.
PE184-50-220 4-Way 1.7 liters
PE184-2-50-220 8.4 liters††4-Way
Advance HoldReturn†
Remote Motor Control (3.1 m) on/off .37 kW
220 volts50/60 Hz A.C.,Single Phase
Description
Remote Motor Control (3.1 m) on/off
* Also for use with special single-acting cylinder applications.** Available with 115 Volt, 60/50 Hz motor (to order, remove suffix “50-
220” from pump order number). Specify voltage when ordering.† Holds when motor is shut off and valve is in “advance” position.
†† Pumps supplied with 7.6 L oil (usable oil is 5.7L), will hold 9.5 Lwhen filled to within 12.7 mm below reservoir cover plate.
∞ Not to be used for lifting.
Special crimping pump. See details onpage 44. PE184C-50-220* 1.7 litersAdvance Return Remote Control
(3.1 m) on/off4-Way
Special crimping pump. See details onpage 44. PE183C50-220 ∞ 1.7 litersAdvance Hold Return Remote Motor Control
(7.6 m) on/offSpecial, for
crimping only
®
46 www.powerteam.com
PUM
PS
Electric Hydraulic Pumps360.8 cu. cm./min. — .75 kW (PE21 Series)
Low-speed, high-torque pump designed specifically for heavy-duty, extended-cycleoperations. Generally recommended for cylinders up to 75 ton.
700 bar
• Totally enclosed, fan cooled induction motor: 2-Speed.75 kW, 1,437 rpm, 50 Hz, single phase. Thermaloverload protection.
• Remote control, with 3.1 m cord is standard on pumpswith solenoid valves only. Manual valve pumps have“Stop”, “Start” and “Run/Off/Pulse” switches. Pumpcontrols are moisture and dust resistant. Electricalcontrols comply with new NEMA 12 standards.
• “Posi-Check®” valve provides positive load holding.• All metal unit has motor drip cover with carrying
handles and lifting lug.• Very low noise level of 70 dBA @ 700 bar.• Has electrical shut down in the event of electrical
interruption. Pump shuts off and will not automaticallystart up until operator presses the pump start button.
• 24 volt control circuits on units with remote controlsprovide additional user/operator safety.
19 and 38 liter reservoirs
For extra oil capacity there is a 19 and 38 liter reservoiravailable for the PE series pumps. See these accessorieson page 165.
PE213-50-220
PE214-50-220
PE214S-50-220
PERFORMANCE
LR19814
Hoses, Fittings& GaugesPages74-80
Cylinder/PumpSpeed/SelectionChart Page178
PumpAccessoriesPages161-165
Choosing TheRight PumpPages181-184
®
47www.powerteam.com
PUMPS
EB
H J
A
G
FC
D
K
rpm
* Measured at a 0.9 meter distance, all sides.*** For 50.8 mm dia. swivel casters, order (4) No. 10494.
† Shipping weight with manual valve; add 6.4 kg for pump with solenoidvalve.
SPECIFICATIONS AND DIMENSIONS
PumpNo.
Max.Press.Output
dBA atIdle and
700bar
AmpDraw at
700bar
Oil Delivery (liters/min.@) Dimensions (mm) Prod.Wt.
w/Oil(kg)
7bar
70bar
350bar
700bar A B C D E F G H J K ***
PE21Series 700 bar 1,437 70 * See Chart
Below 3.6 0.4 0.4 0.3 543 292 241 165 254 203 359 241 82.61⁄2 –20UNF
44.4†
.75 kW pump with 9.5 liter reservoirand manual valve.
PE213-50-220, except has solenoidoperated remote valve.
Advance HoldReturn
ValveType No. Function
Reservoir(Usable)Motor
OrderNo.
PE213-50-220 3-Way 9.4 liters
PE213S-50-220 9.4 liters
9520*
3-Way 9599†
Advance HoldReturn
.75 kW 220 Volt50 Hz††, Single Phase
Description
ORDERING INFORMATION ‡
See current price list for shipping weights.
SINGLE-ACTING
.75 kW 220 Volt50 Hz††, Single Phase
Max. Amp Draw @700 bar
220V - 7.5 amps115V - 15 amps220V - 7.5 amps115V - 15 amps
.75 kW pump with 9.5 liter reservoirand manual valve.
PE214-50-220, except has solenoidoperated remote valve.
Advance HoldReturn
ValveType No. Function
Reservoir(Usable)Motor
OrderNo.
PE214-50-220 4-Way 9.4 liters
PE214S-50-220 9.4 liters
9506*
4-Way 9512†
Advance HoldReturn
.75 kW 220 Volt50 Hz††, Single Phase
Description
DOUBLE-ACTING
.75 kW 220 Volt50 Hz††, Single Phase
Max. Amp Draw @700 bar
220V - 7.5 amps115V - 15 amps220V - 7.5 amps115V - 15 amps
* Manual valve. Pump is equipped with RUN/OFF/PULSE switch for control of motor.† Solenoid valve. Pump is equipped with a remote
control switch with 3.1 meter cord.†† Prewired at factory for this voltage. PE21 series available in 115V 60Hz or 230 60Hz.
Please specify when ordering. Example: for 115V 60Hz order PE213; for 230V 60Hz orderPE213-230.
‡ Some Power Team pumps are available in specialconfigurations not listed in this catalog. Power Team can“Assemble to Order” pumps with special seals, voltages,valves, relief valve settings, etc. For your special requirementsplease consult your local distributor or the Power Team factory.
PE21 series pump and RD5513 cylinderused in a special press that producespharmaceutical-grade extracts for herbalmedicines.
®
48 www.powerteam.com
PUM
PS
Electric Hydraulic Pumps410 cu. cm./min. — 1.12 kW (PED Series)
Ideal for running multiple tools or cylinders from one power unit.Generally recommended for cylinders up to 75 tons.
700 bar
• Two-speed pumps have the same low pressure andhigh pressure flows from both valves. Flows andpressures of each pump are independent.
• Both pumps deliver 4.8 L/min. of oil @ 7 bar and .4L/min. @ 700 bar.
• Have 1.12 kW, 220 volt, 50 Hz induction motor, 3.1meter remote control and 19 liter steel reservoir.
• Models available for operating single-acting or double-acting cylinders.
• Each power unit contains two separate pumps and twoseparate valves. This allows operator to controlmultiple processes with just one power unit.
• Both pumps on each power unit are equipped with anexternally adjustable pressure relief valve.
• Not recommended for frequent starting and stopping.
PERFORMANCE
PED254S-50-220
PED253-50-220
PED254-50-220
Hoses, Fittings& GaugesPages74-80
Cylinder/PumpSpeed/SelectionChart Page178
PumpAccessoriesPages161-165
Choosing TheRight PumpPages181-184
®
49www.powerteam.com
PUMPS
DOUBLE-ACTING
1.12 kW pump with 19 liter reservoir.Valve has “Posi-Check ®” feature.
PED254, except has solenoidoperated remote valve.
Advance HoldReturn
ValveType No. Function
Reservoir(Usable)Motor
ControlSwitch ††
OrderNo.
PED254-50-220 4-Way 16 liters
PED254S-50-220 16 liters
9506
4-Way 9512
Advance HoldReturn Remote Motor
1.12 kW 220V,50 Hz A.C. Single Phase
Description
Remote Valve
†† Control switch wired with line voltage. All remotes are 3.1 meters long.
1.12 kW pump with 19 liter reservoir.Valve has “Posi-Check ®” feature.
ValveType No. Function
Reservoir(Usable)Motor
ControlSwitch ††
OrderNo.
PED253-50-220 3-Way 16 liters9520 Advance HoldReturn Remote Motor 1.12 kW 220V,
50 Hz A.C. Single Phase
Description
ORDERING INFORMATION
See current price list for shipping weights.
SINGLE-ACTING
* Noise level reading (dBA) measured at a 0.9 meter distance, all sides.
SPECIFICATIONS AND DIMENSIONS
Dimensions (mm)Oil Delivery (liters/min. @)
GB
E FC
H
A
D
dBA at ProductMaximum Idle and Amp Draw at Weight
Pump Pressure 700 700 bar 7 48.2 350 700 With OilNo. rpm Output bar (220 V.) bar bar bar bar A B C D E F G H (kg)PED
Series 2,874 700 bar 87/85* 11 4.8 0.6 0.6 0.4 527 457 292 216 419 229 457 330 77
®
50 www.powerteam.com
PUM
PS
Electric Hydraulic Pumps.48 L/min. — .75 kW (PE30 Vanguard® Series)
Two-speed high performance pump at a low price. Ideal for maintenance and constructionapplications where low voltage is a concern. Generally recommended for cylinders up to100 tons.
700 bar
• Two-speed Vanguard® 30 series pumps deliver apowerful punch to operate single-acting or double-acting cylinders.
• Rugged all metal construction; integral roll cageprotects pump from abuse.
• Equipped with a .75 kW, single phase, permanentmagnet motor.
• Choice of 110/115 volt or 220/230 volt, 50/60 Hz.• Require relatively low voltage, making them ideal for
use in general construction applications. Amp draw at700 bar only is 13 amps @ 110/115 volts and 6.5amps @ 220/230 volts.
• Pump will start under full load even when voltage isreduced to 50% of nominal rating.
• High performance to weight ratio. Deliver up to .48liters of oil per minute at maximum operating pressureof 700 bar.
• Choice of 4.7 or 6.6 liter aluminum reservoirs.• Quiet operation: 82 dBA @ 700 bar and 87 dBA @ 0
bar. CSA rated for intermittent duty.• For faster cylinder return, the 9520 “Posi-Check®” style
manual valve has improved porting.• All models having remote controls and/or solenoid
valves feature 24 volt controls. An internal pressureregulator is optional on all pumps.
• Portable - all metal hydraulic pump weighs only 18.6kg. with oil (4.7 liter reservoir).
PE302-50-220
PE302S-50-220
PE304R-2-50-220
PERFORMANCE
LR19814
Hoses, Fittings& GaugesPages74-80
Cylinder/PumpSpeed/SelectionChart Page178
PumpAccessoriesPages161-165
Choosing TheRight PumpPages181-184
ORDERING INFORMATION
See current price list for shipping weights.
SINGLE-ACTING
®
51www.powerteam.com
PUMPS
H
W LSPECIFICATIONS AND DIMENSIONS
Base model .75 kW pump with 4.7 literreservoir & 2 position valve.
PE302-220, except has 6.6 literreservoir.PE302-220, except has remote motorcontrol.
PE302R-220, except has 6.6 literreservoir.PE302R-220, except also has solenoidoperated remote valve.
PE302S-220, except has 6.6 literreservoir.PE302-220, except has “Auto Dump”valve.
PE302A-220, except has 6.6 literreservoir.Base model .75 kW pump with 4.7liter reservoir & 3 position valve.
PE303-220, except has 6.6 literreservoir.PE303-220, except has remote motorcontrol.
PE303R-220, except has 6.6 literreservoir.
ValveType No. Function
Reservoir(Usable)Motor (4,000 rpm) ††
ControlSwitch ††
OrderNo.
PE302-220 ∞ 4.5 liters**9584 Advance Return On/Off/Pulse Switch
.75 kW 220/230 VAC,50/60 Hz AC, Single Phase
.75 kW 220/230 VAC,50/60 Hz AC, Single Phase
.75 kW 220/230 VAC,50/60 Hz AC, Single Phase
.75 kW 220/230 VAC,50/60 Hz AC, Single Phase
.75 kW 220/230 VAC,50/60 Hz AC, Single Phase
.75 kW 220/230 VAC,50/60 Hz AC, Single Phase
.75 kW 220/230 VAC,50/60 Hz AC, Single Phase
.75 kW 220/230 VAC,50/60 Hz AC, Single Phase
.75 kW 220/230 VAC,50/60 Hz AC, Single Phase
.75 kW 220/230 VAC,50/60 Hz AC, Single Phase
.75 kW 220/230 VAC,50/60 Hz AC, Single Phase
.75 kW 220/230 VAC,50/60 Hz AC, Single Phase
PE302-2-220 6.1 liters***9584 Advance Return On/Off/Pulse Switch
PE302R-220 4.5 liters**9584 Advance Return Remote MotorControl (3.1 m)
PE302R-2-220 6.1 liters***9584 Advance Return Remote MotorControl (3.1 m)
PE302S-220 4.5 liters**9579 Advance Return Remote Motor &Valve (3.1 m)
PE302S-2-220 6.1 liters***9579 Advance Return Remote Motor &Valve (3.1 m)
PE302A-220 4.5 liters**9610 Automatic PilotOperation
Remote MotorControl (3.1 m)
PE302A-2-220 6.1 liters***9610 Automatic PilotOperation
Remote MotorControl (3.1 m)
PE303-220 4.5 liters**9520* Advance HoldReturn
On/Off/Pulse Switch
PE303-2-220 6.1 liters***9520* Advance HoldReturn
On/Off/Pulse Switch
PE303R-220 4.5 liters**9520* Advance HoldReturn
Remote MotorControl (3.1 m)
PE303R-2-220 6.1 liters***9520* Advance HoldReturn
Remote MotorControl (3.1 m)
Description3-Way, 2 Pos.3-Way, 2 Pos.3-Way, 2 Pos.3-Way, 2 Pos.3-Way, 2 Pos.3-Way, 2 Pos.Auto
DumpAuto
Dump3-Way, 3 Pos.3-Way, 3 Pos.3-Way, 3 Pos.3-Way, 3 Pos.
Base model .75 kW pump with 4.7 L res.& 4-way valve for double-acting systems.
PE304-220, except has 6.6 liter reservoir.
PE304-220, except has remote motorcontrol.PE304R-220, except has 6.6 literreservoir.
ValveType No. Function
Reservoir(Usable)Motor (4,000 rpm) ††
ControlSwitch
OrderNo.
PE304-220 4.5 liters**9506* Advance HoldReturn
On/Off/Pulse Switch
.75 kW 220/230 VAC,50/60 Hz AC, Single Phase
.75 kW 220/230 VAC,50/60 Hz AC, Single Phase
.75 kW 220/230 VAC,50/60 Hz AC, Single Phase
.75 kW 220/230 VAC,50/60 Hz AC, Single Phase
PE304-2-220 6.1 liters***9506* Advance HoldReturn
On/Off/Pulse Switch
PE304R-220 4.5 liters**9506* Advance HoldReturn
Remote MotorControl (3.1 m)
PE304R-2-220 6.1 liters***9506* Advance HoldReturn
Remote MotorControl (3.1 m)
Description
DOUBLE-ACTING
4-Way, 3 Pos.Tandem Ctr.
4-Way, 3 Pos.Tandem Ctr.
4-Way, 3 Pos.Tandem Ctr.
4-Way, 3 Pos.Tandem Ctr.
* “Posi-Check®” valve design, “Posi-Check®” guards against pressure losswhen valve is shifted from “advance” to “hold” position.
** Shipped with 3.8 liters of oil (3.4 liters usable).*** Shipped with 7.6 liters of oil.
∞ Not to be used for lifting. Best suited for crimping, pressing & punchingapplications.
†† For 110/115 volt, 50/60 Hz. remove suffix “- 220” (example PE302).
Maximum dBA at Amp Draw Oil Del. (liters/min. @) Prod. Wt.Pressure Idle & 220V at 7 35 70 350 700 Overall With Oil
Pump No. Output 700 bar 700 bar bar bar bar bar bar Dimensions (mm) (kg)PE30 Series 700 bar 87/82 7 4.8 3.2 0.7 0.6 0.5 254L x 229W x 406H 18.6w/4.7 liter res.PE30 Series 700 bar 87/82 7 4.8 3.2 0.7 0.6 0.5 343L x 241W x 419H 22.2w/6.6 liter res.
®
52 www.powerteam.com
PUM
PS
Hydraulic Intensifier
Converts low-pressure portable hydraulic pumps or on-board hydraulic systems, into highpressure power sources. Pressure ratio 5:1.
700 bar
• Converts low pressure (138 bar) portable pumps oron-board hydraulic systems of utility trucks, etc., intohigh pressure (700 bar) power sources.
• Applications include utilities, railroads, construction,riggers and others.
• Operates single- or double-acting cylinders, jacks, andtools such as crimpers, spreaders, cable cutters, ortire tools.
• May be used to operate two separate, single-actingtools (with integral valves) independently, withoutneed for additional manifold.
• Compact and rugged for use inside a utility vehicleaerial bucket or stowing in a vehicle.
• Control valve included. Other Power Team valvesavailable as an option to suit your specific application,if needed; consult factory.
• No reservoir level to maintain; uses low pressure systemas oil supply.
• Has 3⁄8" NPTF ports; compatible with standard fittingsfor low and high pressure systems.
HB444
HB443
Hoses, Fittings& GaugesPages74-80
®
53www.powerteam.com
PUMPS
WA
RN
ING
A
B
C
DE
F
Description
OrderNo.
ValveInput Flow
Range†
OperatingPressure
(bar)Output Flow
Range
HB443 3-Way/3-Position
DIMENSIONS (MM)
No. A B C D E F
HB44Series 219.1 368.3 155.6 69.9 114.3 266.7
† For maximum efficiency, recommended input flow is 19 L/min. at a maximum pressure of 140 bar. Higher flows and/or pressures must be compensatedfor at the system pump (e.g., relief valve, variable flow devices, etc.).
* “Posi-Check®” valve design, “Posi-Check ®” guards against pressure loss when valve is shifted from “advance” position to “hold” position.
Type
9520*
No.
AdvanceHold Return
Function
0 - 37.9L/min. 20.7 - 138 0 - 9.5
L/min.
ORDERING INFORMATION
See current price list for shipping weights.
SINGLE-ACTING
Description
OrderNo.
ValveInput Flow
Range†
OperatingPressure
(bar)Output Flow
Range
HB444 4-Way/3-Position
Type
9506*
No.
AdvanceHold Return
Function
0 - 37.9L/min. 20.7 - 138 0 - 9.5
L/min.
SINGLE- OR DOUBLE-ACTING
7.2
Product Wt.(kg)
0.7 L/min.
Output Flow @700 bar
Hydraulic intensifier for single-acting systems
Hydraulic intensifier for double-acting systems
®
54 www.powerteam.com
PUM
PS
Electric Hydraulic Pumps0.6 L/min. — 1.12 kW (PE46 Series)
Two-speed high performance pump. Best suited for under the roof maintenance and someproduction applications. Generally recommended for cylinders up to 150 ton.
700 bar
• Two-speed high performance pump.• For use with single- or double-acting cylinders at
operating pressures to 700 bar.• Equipped with a 1.12 kW, 2,875 rpm single-phase, 50
Hz thermal protected induction motor that starts underfull load. Noise level of 77-81 dBA.
• CSA rated for intermittent duty.• All equipped with a 3.1 meter remote control except
PE462S-50-220 which has a 7.6 meter remote control.• Large selection of valve options. See pages 144-155.• 24 volt control circuit on all units with remote control
for user/operator safety.
PERFORMANCE
PE462S-50-220
PE464-50-220PE462A-50-220
LR19814
Hoses, Fittings& GaugesPages74-80
Cylinder/PumpSpeed/SelectionChart Page178
PumpAccessoriesPages161-165
Choosing TheRight PumpPages181-184
Maximum dBA at Amp Draw Dimensions (mm) Prod. Wt.Pressure Idle and 220 V - at 0 7 350 700 With Oil
Pump No. Output rpm 700 bar 700 bar bar bar bar bar A B C D E F G (kg)PE46 Series 700 bar 2,875 77/81* 13 6.7 6.0 0.7 0.6 499 173 292 254 378 241 203 35.8PE46-E220 700 bar 2,875 77/81* 13 6.7 6.0 0.7 0.6 499 173 292 254 378 241 203 41.3
®
55www.powerteam.com
PUMPS
A
B
GF
DC
E
* Available with 115 V., 60 Hz motor (to order, remove suffix “50-220” from pump order number).** “Advance” position holds pressure with motor shut off.*** Usable oil is calculated with the oil fill at the recommended level of 12.7 mm below reservoir cover plate.† “Advance” position holds pressure with motor shut off. “Return” position returns cylinder.††† The remote motor control switch on PE46 series pumps is 24 volt.∞ Not to be used for lifting. When pump is shut off, oil returns to reservoir.(1) These pumps are marked for meeting the requirements of 89/366/EEC and 73/23/EEC. In addition, they meet the European Union Machinery
Directive and are furnished with a Declaration of Incorporation. For additional information contact your nearest Power Team facility.
Oil Del. (liters/min. @)†
SPECIFICATIONS AND DIMENSIONS
* Measured at 0.9 meter distance, all sides. † Typical delivery. Actual flow will vary with field conditions.
Base model 1.12 kW pump with 9.5liter metal reservoir.PE462-50-220, except has solenoidvalve.PE462-50-220, except has “dumpvalve”.
1.12 kW pump with 9.5 liter metalreservoir. Meets CE requirements.
PE462-50-220, except has solenoidvalve. Meets CE requirements.PE462-50-220, except has “dumpvalve”. Meets CE requirements.
AdvanceReturn**
ValveType No. Function
Reservoir(Usable)***Motor
ControlSwitch †††
OrderNo.
ORDERING INFORMATION
See current price list for shipping weights.
SINGLE-ACTING
PE462-50-220 3-Way 9.4 liters
PE462S-50-220 9.4 liters
PE462A-50-220∞
PE462-E220
PE462S-E220
PE462A-E220∞
9.4 liters
9584
9610
3-Way 9579
AdvanceReturn†
AdvanceReturn
Remote Motor Control (3.1 m) on/off
1.12 kW220 V*
50 Hz, Single Phase
Description
DOUBLE OR MULTI SINGLE-ACTING
PE462-50-220, except has 9500double-acting valve.
PE462S-50-220, except has 9592double-acting valve.
AdvanceReturn**
ValveType No. Function
Reservoir(Usable)***Motor
ControlSwitch †††
OrderNo.
PE464-50-220 4-Way 9.4 liters
PE464S-50-220 9.4 liters
9500
3/4-Way 9592
Advance HoldReturn†
Remote Motor Control (3.1 m) on/off 1.12 kW
220 V*50 Hz, Single Phase
Description
Auto/Dump3-Way
Remote Motor/Valve (7.6 m)
Remote Motor Control (3.1 m) on/off
AdvanceReturn**
3-Way 9.4 liters
9.4 liters
9.4 liters
9584
9610
3-Way 9579
AdvanceReturn†
AdvanceReturn
Remote Motor Control (3.1 m) on/off
Auto/Dump3-Way
Remote Motor/Valve (7.6 m)
Remote Motor Control (3.1 m) on/off
Remote Motor/Valve(3.1 m)
Same as PE464-50-220, but alsomeets CE requirements.
Same as PE464S-50-220, but alsomeets CE requirements.
AdvanceReturn**
PE464-E220 4-Way 9.4 liters
PE464S-E220 9.4 liters
9500
3/4-Way 9592
Advance HoldReturn†
Remote Motor Control (3.1 m) on/off
Remote Motor/Valve(3.1 m)
(1)
(1)
®
56 www.powerteam.com
PUM
PS
Electric Hydraulic Pumps0.9 L/min. — .84 kW (PE55 Vanguard® Series)
This is a proven pump for many of the toughest applications, and for starting under low voltageconditions. The PE55 pump has earned its place as the mainstay for heavy construction and theconcrete stressing business world wide. Generally recommended for cylinders up to 200 tons.
700 bar
• Two-speed high performance. Forty years of reliability andconstant improvement make Vanguard® pumps a mainstayworldwide. Some original pumps are still in service!
• Designed for operating pressures to 700 bar. CSA rated forintermittent duty. Noise level of 90 dBA.
• Has .84 kW, 12,000 rpm, 220 volt, 50 Hz universal motor;draws 13 amps at full load, starts at reduced voltage.
• Internal relief valve preset at 700 bar, 9.5 liter metalreservoir.
• All have 3.1 meter remote motor control except PE552S-50-220 which has a 7.6 meter remote motor and valvecontrol.
• True unloading valve achieves greater pump efficiency,allowing higher flows at maximum pressure.
• Reservoirs available in sizes up to 37.9 liters. Seeaccessories page 165.
• Light weight and portable. Best weight to performanceratio of all Power Team pumps.
• “Assemble to Order” System: There are times when acustom pump is required. Power Team’s “Assemble toOrder” system allows you to choose from a wide range ofpre-engineered, off-the-shelf components to build acustomized pump to fit specific requirements. By selectingstandard components you get a “customized” pump without“customized” prices. All pumps come fully assembled, lessoil and ready for work. See pages 70-73.
PE552-50-220
PE554S-50-220
PE554PT-50-220
PERFORMANCE
A
D
FC
EB
G
4 mounting holes 1⁄2"–20
LR19814
Hoses, Fittings& GaugesPages74-80
Cylinder/PumpSpeed/SelectionChart Page178
PumpAccessoriesPages161-165
Choosing TheRight PumpPages181-184
dBA at Amp ProductMaximum Idle and Draw at Weight
Pump Pressure 700 700 bar 7 48.2 350 700 With OilNo. rpm Output bar (220 V.) bar bar bar bar A B C D E F G H (kg)
PE55 Series 12,000 700 bar 90/89* 13 11.3 7.1 1.2 0.9 464 292 241 178 254 203 356 – 29.4
PE55-E220 12,000 700 bar 87/85* 13 11.3 7.1 1.2 0.9 520 292 241 178 254 203 391 – 29.4
®
57www.powerteam.com
PUMPS* Noise level reading (dBA) measured at a 0.9 meter distance, all sides.
SPECIFICATIONS AND DIMENSIONS
Dimensions (mm)Oil Delivery (liters/min. @)
DOUBLE-ACTING
Base model .84 kW pump with 9.5 literres., remote motor control & 3-way valve.
PE552-50-220, except also has solenoidoperated remote valve.
PE552-50-220, except has “Auto Dump”valve.
.84 kW pump with 9.5 liter reservoir.Valve has “Posi-check” feature.
ValveType No. Function
Reservoir(Usable)Motor
ControlSwitch ††
OrderNo.***
PE552-50-220 8.4 liters9582 AdvanceReturn** Remote Motor .84 kW*, 220 V.
50 Hz A.C., Single Phase.84 kW*, 220 V.
50 Hz A.C., Single Phase.84 kW*, 220 V.
50 Hz A.C., Single Phase.84 kW*, 220 V.
50 Hz A.C., Single Phase
PE552S-50-220 8.4 liters9579 AdvanceReturn
Remote Motor &Valve
PE552A-50-220∞ 8.4 liters9610 Advance HoldReturn Remote Motor
PE553-50-220 8.4 liters9520 Advance HoldReturn Remote Motor
Description
3-Way
3-Way
Auto/Dump
Same as PE552-50-220, but also meetsCE requirements.
Same as PE552S-50-220, but also meetsCE requirements.
Same as PE552A-50-220, but also meetsCE requirements.
PE552-E220 8.4 liters9582 AdvanceReturn** Remote Motor
PE552S-E220 8.4 liters9579 AdvanceReturn
Remote Motor &Valve
PE552A-E220∞ 8.4 liters9610 Advance HoldReturn Remote Motor
3-Way
3-Way
Auto/Dump
3-Way †
ORDERING INFORMATION
See current price list for shipping weights.
SINGLE-ACTING
.84 kW pump with 9.5 L res. and 4-wayvalve for double-acting systems.
PE554-50-220, except has 9500 tandemcenter valve.
For use with single-acting Spring Seat,Stressing Jack or double-acting cyl.
For use with single- or double-actingPower Seat, Stressing Jacks ONLY.
Pump suitable to run multiple springreturn tools.
Pump equipped with 3/4-way solenoidvalve.Pump suitable to run multiple springreturn tools.
Pump equipped with 3/4-way solenoidvalve.
ValveType No. Function
Reservoir(Usable)Motor
ControlSwitch ††
OrderNo.***
PE554-50-220 8.4 liters9506 Advance HoldReturn Remote Motor .84 kW*, 220 V.
50 Hz A.C., Single Phase.84 kW*, 220 V.
50 Hz A.C., Single Phase.84 kW*, 220 V.
50 Hz A.C., Single Phase.84 kW*, 220 V.
50 Hz A.C., Single Phase
PE554T-50-220 8.4 liters9500 Advance HoldReturn Remote Motor
PE554P-50-220 8.4 liters9500 Advance HoldReturn Remote Motor
PE554PT-50-220 8.4 liters9628 Advance HoldSequenced Return Remote Motor
Description
4-Way †
4-Way
4-Way
4-Way
.84 kW*, 220 V.50 Hz A.C., Single Phase 8.4 liters9511 ††† Advance Hold
Return Remote Motor 4-Way
.84 kW*, 220 V.50 Hz A.C., Single Phase 8.4 liters9592 Advance Hold
ReturnRemote Motor &
Valve3/4-Way
PE554C-50-220
PE554S-50-220
8.4 liters9511 ††† Advance HoldReturn Remote Motor 4-Way
8.4 liters9552 Advance HoldReturn
Remote Motor &Valve3/4-Way
PE554C-E220
PE554S-E220
* Pumps available with 115 volt, 60/50 Hz motors (to order, remove the -50-220 suffix from the order number). See “Assemble to Order” pump optionson pages 70-73.
** Holds with motor shut off.*** To order PE55 series pumps with CSA approval, add “–C” to the Order No.† Valves have “Posi-Check®” feature. †† Control switch wired with line voltage. All remotes are 3.1 meters long
except for PE552S-50-220 which is 7.6 meters long.
††† Valving allows alternate and independent operation of two different springreturn tools. Valve holds pressure only while valve is in “A” or “B” portposition with pump motor shut off.
∞ Not to be used for lifting.(1) These pumps are marked for meeting the requirements of 89/366/EEC
and 73/23/EEC. In addition, they meet the European Union MachineryDirective and are furnished with a Declaration of Incorporation. Foradditional information contact your nearest Power Team facility.
(1)
(1)
®
58 www.powerteam.com
PUM
PS
Electric Hydraulic Pumps0.9 L/min. — .84 kW (PE60 Vanguard Supreme® Series)
Compact, light weight pump with numerous standard features. Excellent choice for ruggedapplications and low voltage starting. Recommended for stressing tools.
700 bar
• The Vanguard® tradition of reliability, two-speed highperformance and ease of maintenance has reached anew standard.
• Long, trouble free life in the most demanding workenvironments. For operating single- or double-actingcylinders, or stressing jacks at operating pressures to700 bar.
• Powered by .84 kW, 220 volt, 60/50 Hz single phasemotor. Improved motor insulation extends motor lifeand is in full CSA compliance. Starts under load, evenat the reduced voltages at construction sites.
• Quiet operation: 80 to 85 dBA at 0.9 meter distancewith 54 dBA background.
• Optional fan-driven external oil cooler includesrollover guard.
• Insulated carrying handle. Pump weighs only 22.7 kgwithout oil cooler option: 8.2 kg less than similarcompetitive units!
• Integral 102 mm dia. fluid-filled pressure gauge withsteel bezel complies with ASME B40.1 Grade A. With 0to 700 bar pressure range in 7 bar increments.
• Sealed 4.34 liter (usable) reservoir. Reservoir drainport is standard.
• Standard oil level sight gauge for accurate oil levelmonitoring.
• External spin-on filter removes contaminants fromcirculating oil to maximize pump, valve andcylinder/tool life.
PE604T-220w/cooler
PERFORMANCE
PE604T-220
LR19814
Hoses, Fittings& GaugesPages74-80
Cylinder/PumpSpeed/SelectionChart Page178
PumpAccessoriesPages161-165
Choosing TheRight PumpPages181-184
Oil Delivery (liters/min. @)
Maximum dBA at Amp Prod. Wt.Pump No. rpm Pressure idle and draw at 6.9 48.2 350 700 A B C D E F G with Oil
Output 700 bar 700 bar bar bar bar bar (kg)
PE604T-220 12,000 700 bar 80/85 13 11.3 7.1 1.2 0.9 263.5 301.6 457.2 152.4 381 101.6 27.2
PE604PT-220 12,000 700 bar 80/85 13 11.3 7.1 1.2 0.9 263.5 301.6 457.2 152.4 381 101.6 27.7
®
59www.powerteam.com
PUMPS
A
F
G
B
E
C
D
NOTE: Unloading pressure is 70 bar.Consult factory for PE60 pump models with other control and valve options.For 115 volt, 50/60 Hz, single-phase models, remove -220 suffix
SPECIFICATIONS AND DIMENSIONS
3⁄8"NPTF
3⁄8"NPTF
.84 kW pump with 4.73 liter reservoir& valve for double-acting systems.
ValveType No. Function
Reservoir(Usable)Motor
OrderNo.
PE604T-220 4.34 liters9500 Advance HoldReturn
.84 kW 220 VAC60/50 Hz, Single Phase
Description
ORDERING INFORMATION
See current price list for shipping weights.
SINGLE-ACTING, SPRING SEAT, STRESSING JACK OR DOUBLE-ACTING CYLINDER
Control Switch
On/Off/Pulsecontrol switch
4-Way,3-position
PE604T-220, except has special valvefor post tensioning application only.
ValveType No. Function
Reservoir(Usable)Motor
OrderNo.
PE604PT-220 4.34 litersAdvance HoldSequenced Return
.84 kW 220 VAC60/50 Hz, Single Phase
Description
SINGLE-ACTING OR DOUBLE-ACTING POWER SEAT, STRESSING JACKS ONLY
Control Switch
On/Off/Pulsecontrol switch
4-Way,3-position
9628model C
OPTIONAL253219: Oil cooler kit for PE604T or PE604PT, 115 VAC (model “C” only). Weight 2.7 kg253220: Oil cooler kit for PE604T-220 or PE604PT-220, 220 VAC (model “C” only). Weight 2.7 kg
Dimensions (mm)
®
60 www.powerteam.com
PUM
PS
Electric Hydraulic Pumps0.8 L/min. — 1.49 kW (PQ60 Series “Quiet Pump”)
Quiet operating, low speed, high torque pump designed specifically for heavy duty,extended cycle operation. Ideal for press operation. Generally recommended for cylindersup to 200 ton.
700 bar
• For operating single- or double-acting cylinders. Two-speed, high performance pumps are ideal for heavyduty, extended cycle operation at operating pressuresto 700 bar.
• Metal shroud keeps dirt and moisture out of motor andelectrical components.
• The “Posi-Check®” feature on valves, means load won'tdrop when shifting from “advance” to “hold”, makingthese pumps ideal for operating fixtures and holdingpressure for extended periods of time.
• Electrical shut-down feature prevents unintentionalrestarting of motor following an electrical serviceinterruption.
• Internal relief valve limits pressure to 700 bar. Externalrelief valve is adjustable from 70 to 700 bar.
• Pumps operate below maximum OSHA noise limitation(74-76 dBA).
• Start and operate under full load, even with voltagereduced 10%.
PQ603-50-220
PQ604-50-220
PERFORMANCE
LR19814
Hoses, Fittings& GaugesPages74-80
Cylinder/PumpSpeed/SelectionChart Page178
PumpAccessoriesPages161-165
Choosing TheRight PumpPages181-184
PQ604S-50-220
638
®
61www.powerteam.com
PUMPS
EB
H J
A
G
FC
D
K
rpm
* Measured at a 0.9 meter distance, all sides.** Total weight with oil and 3-way solenoid valve. Subtract 4.5 kg to
obtain weight of pump with manual valve.
*** For 50.8 mm dia. swivel casters, order (4) No. 10494.
SPECIFICATIONS AND DIMENSIONS
PumpNo.
Max.Press.Output
dBA atIdle and700 bar
AmpDraw at700 bar
Oil Delivery (liters/min.@) Dimensions (mm) Prod.Wt.
w/Oil(kg)
7bar
70bar
350bar
700bar A B C D E F G H J K ***
PQ60Series
700bar 1,437 74/76 * See Chart
Below 9.7 0.9 0.9 0.8 362 394 184 308 338 373 237 122.21⁄2 –20UNF
76.6**
1.49 kW pump with 21.6 literreservoir and manual valve.
PQ603-50-220, except hassolenoid operated remote valve.
Advance HoldReturn
ValveType No. Function
Reservoir(Usable)Motor
OrderNo.
PQ603-50-220 3-Way 20 liters
PQ603S-50-220 20 liters
9520*
3-Way 9599†
Advance HoldReturn
1.49 kW 220 Volt50 Hz††, Single Phase
Description
ORDERING INFORMATION ‡
See current price list for shipping weights.
SINGLE-ACTING
1.49 kW 220 Volt50 Hz††, Single Phase
Max. Amp Draw @700 bar
115V - 22 amps220 V - 11 amps115V - 22 amps220 V - 11 amps
1.49 kW pump with 21.6 liter.reservoir and manual valve.
PQ604-50-220, except hassolenoid operated remote valve.
Advance HoldReturn
ValveType No. Function
Reservoir(Usable)Motor
OrderNo.
PQ604-50-220 4-Way 20 liters
PQ604S-50-220 20 liters
9506*
4-Way 9512†
Advance HoldReturn
1.49 kW 220 Volt50 Hz††, Single Phase
Description
DOUBLE-ACTING
1.49 kW 220 Volt50 Hz††, Single Phase
Max. Amp Draw @700 bar
115V - 22 amps220 V - 11 amps115V - 22 amps220 V - 11 amps
* Manual valve. Pump is equipped with RUN/OFF/PULSE switch for control of motor.† Solenoid valve. Pump is equipped with a remote
control switch with 3.1 meter cord.†† PQ60 series also available in 115V, 60 Hz or 230V, 60 Hz. Please specify when ordering.
Example: for 60 Hz order PQ603-115; for 230V 60 Hz order PQ603.
‡ Some Power Team pumps are available in specialconfigurations not listed in this catalog. Power Team can“Assemble to Order” pumps with special seals, voltages,valves, relief valve settings, etc. For your special requirementsplease consult your local distributor or the Power Team factory.
®
62 www.powerteam.com
PUM
PS
Electric Hydraulic Pumps1.6 L/min. — 2.24 kW (PQ120 Series “Quiet Pump”)
Quiet operating, low speed, high torque pump designed specifically for heavy duty,extended cycle operation. Ideal for press operation. Generally recommended for cylindersup to 400 tons.
700 bar
• For operating single- or double-acting cylinders. Two-speed, high performance pumps are ideal for heavyduty, extended cycle operation at operating pressuresto 700 bar.
• Pumps operate below maximum OSHA noise limitation.• Start and operate under full load, even with voltage
reduced 10%.• Electrical shut-down feature prevents unintentional
restarting of motor following an electrical serviceinterruption.
• Internal relief valve limits pressure to 700 bar. Externalrelief valve is adjustable from 70 to 700 bar.
• Pump prewired at factory with a 2.24 kW, 220 volt, 50Hz. 3 Phase motor. Other electrical configurations areavailable. See ordering information on the followingpage.
• 24 volt control circuits on units with remote controlsfor added user/operator safety.
• 2.24 kW (3 phase) motor with thermal overloadprotection. Motor starter and heater element suppliedas standard equipment; no hidden charges!
• Metal shroud keeps dirt and moisture out of motor andelectrical components.
• “Posi-Check®” feature means load won’t drop whenshifting from “advance” to “hold”, making pump idealfor fixed applications and longer operational cycles.
PQ1203-50-220
PQ1204-50-220
PQ1204S-50-220
PERFORMANCE
LR19814
Hoses, Fittings& GaugesPages74-80
Cylinder/PumpSpeed/SelectionChart Page178
PumpAccessoriesPages161-165
Choosing TheRight PumpPages181-184
®
63www.powerteam.com
PUMPS
EB
H J
A
G
FC
D
K
rpm
* Measured at a 0.9 meter distance, all sides.** Total weight with oil and 3-way solenoid valve. Subtract 4.5 kg to
obtain weight of pump with manual valve.
*** For 50.8 mm dia. swivel casters, order (4) No. 10494.
SPECIFICATIONS AND DIMENSIONS
PumpNo.
Max.Press.Output
dBA atIdle and700 bar
AmpDraw at700 bar
Oil Delivery (liters/min.@) Dimensions (mm) Prod.Wt.
w/Oil(kg)
7bar
70bar
350bar
700bar A B C D E F G H J K ***
PQ120Series
700bar 1,437 73/78 * See Chart
Below 9.7 2.1 1.7 1.6 638 362 394 184 308 338 373 237 122.21⁄2 –20UNF
74.3**
2.24 kW pump with 21.6 literreservoir and manual valve.
PQ1203-50-220, except has solenoidoperated remote valve.
Advance HoldReturn
ValveType No. Function
Reservoir(Usable)Motor
OrderNo.
PQ1203-50-220 3-Way 20 liters
PQ1203S-50-220 20 liters
9520*
3-Way 9599†
Advance HoldReturn
2.24 kW 220 Volt50 Hz††, 3 Phase
Description
ORDERING INFORMATION ‡
See current price list for shipping weights.
SINGLE-ACTING
2.24 kW 220 Volt50 Hz††, 3 Phase
Max. Amp Draw @700 bar
220V - 10.5 amps380 V - 6.1 amps220V - 10.5 amps380 V - 6.1 amps
2.24 kW pump with 21.6 literreservoir and manual valve.
PQ1204-50-220, except has solenoidoperated remote valve.
Advance HoldReturn
ValveType No. Function
Reservoir(Usable)Motor
OrderNo.
PQ1204-50-220 4-Way 20 liters
PQ1204S-50-220 20 liters
9506*
4-Way 9512†
Advance HoldReturn
2.24 kW 220 Volt50 Hz††, 3 Phase
Description
DOUBLE-ACTING
2.24 kW 220 Volt50 Hz††, 3 Phase
Max. Amp Draw @700 bar
220V - 10.5 amps380 V - 6.1 amps220V - 10.5 amps380 V - 6.1 amps
* Manual valve. Pump is equipped with RUN/OFF/PULSE switch for control of motor.† Solenoid valve. Pump is equipped with a remote control switch with 3.1 meter cord.†† PQ120 series also available in 230V 60 Hz or 460V 60 Hz. Please specify when ordering.
Example: for 230V 60 Hz order PQ1204S-230; for 460V 60 Hz. order PQ1204S.PQ120 Series also available in 575V 60 Hz. Consult the factory.
‡ Some Power Team pumps are available in specialconfigurations not listed in this catalog. Power Team can“Assemble to Order” pumps with special seals, voltages,valves, relief valve settings, etc. For your special requirementsplease consult your local distributor or the Power Team factory.
PQ603 pump and C256C cylinder used todrive piers to lift and stabilize buildingfoundation.
®
64 www.powerteam.com
PUM
PS
Electric Hydraulic Pumps5.6 L/min. — 7.46 kW (PE400 Series)
Delivers up to 16 L/min. of oil. Ideal for powering high tonnage double-acting cylinders,either singly or in multiple cylinder applications. Generally recommended for cylinders upto 1,000 tons.
700 bar
• Two-speed high output pump delivers up to 16 L/min.of oil. Ideal for powering high tonnage double-actingcylinders, either singly or in multiple cylinderapplications. For operating pressures to 700 bar.
• Low noise level of 73-80 dBA.• Integral electrical shut-down feature prevents
unintentional restarting of motor following an electricalservice interruption. Over-current protection preventsdamage to motor as a result of overheating.
• “Stop” and “Start” control buttons are 24 volt.PE4004-50-220 has a 4-way/3-position manual valve.The PE4004S-50-220 has a 4-way/3-position solenoidvalve with a 24 volt remote hand switch.
• Valves feature “Posi-Check®” which holds the loadwhen shifting from “advance” or “return” to “hold”position.
• External pressure relief valve is adjustable from 104 to700 bar.
• Heavy duty 102 mm dia. casters assure easymaneuvering.
• 75.7 liter (62.8 liters usable) reservoir has a low oillevel sight gauge.
• Powered by a dual voltage 7.46 kW, 3 phase, 1,437rpm motor.
• 3 phase motor has all the electrical componentsnecessary to operate the pump. The customer has nohidden charges when making purchase.
• Deliver 16 L/min. of oil @ 15 bar, 5.6 L/min. of oil @700 bar.
PE4004S-50-220
PERFORMANCE
Hoses, Fittings& GaugesPages74-80
Cylinder/PumpSpeed/SelectionChart Page178
PumpAccessoriesPages161-165
Choosing TheRight PumpPages181-184
Maximum dBA at Amp Draw Prod. Wt.Pressure Idle and at 15 90 350 700 E F w/Oil
Pump No. Output rpm 700 bar 700 bar bar bar bar bar A* B C D Caster Mtg. Caster Mtg. (kg)*
PE4004-50-220 700 bar 1,437 73/80 34 @ 220 V. 16 14 6 5.6 924 635 610 540 394 546 223
PE4004S-50-220 700 bar 1,437 73/80 17 @ 460 V. 16 14 6 5.6 924 635 610 540 394 546 229
®
65www.powerteam.com
PUMPS
7.46 kW pump with 75.7 literreservoir and manual valve.
PE4004-50-220, except hassolenoid operated remote valve.
Advance HoldReturn
ValveType No. Function
Reservoir(Usable)Motor ††
OrderNo.
PE4004-50-220 4-Way 62.8 liters †
PE4004S-50-220 62.8 liters †
9506
4-Way 9512**
Advance HoldReturn
7.46 kW 460 volt*60 Hz, 3 Phase
Description
ORDERING INFORMATION
See current price list for shipping weights.
DOUBLE-ACTING
7.46 kW 460 volt*60 Hz, 3 Phase
* Factory wired for this voltage. For 230V, 60Hz order PE4004-230 or PE4004S-230.** Solenoid valve with remote control.† Usable oil is calculated with oil fill at recommended level at 57.2 mm below cover plate.†† PE400 series available in 380V, 50Hz and 460V, 60Hz. Please specify when ordering. Example: PE4004-50-380 or for 460V, 60 Hz order PE4004 and for 575V,
60 Hz order PE4004S-575.NOTE: Valves for spring return cylinders are available upon request. Consult the factory.
Oil Delivery (liters/min.@) Dimensions (mm)
* Add 127 mm and 3.63 kg when casters are mounted. (Units are supplied with four 102 mm dia. swivel casters.)
SPECIFICATIONS AND DIMENSIONS
EB
FC
D
A
PE4004S pump and RD3006 cylinder usedin a special press which repairs damagedchain links.
®
66 www.powerteam.com
PUM
PS
Gasoline Hydraulic Pumps0.5-0.9 L/min. — 1.49-4.47 kW (PG30-PG55 Series)
Gasoline driven pumps do not need an external power supply to operate, making them anideal choice for remote applications. PG30 series generally recommended for cylinders upto 75 tons. PG55 series generally recommended for cylinders up to 150 tons.
700 bar
• Two-speed high performance pumps ideal forconstruction, structure moving and rigging applications.
• A logical choice at work sites where electricity orcompressed air are unavailable. For single- or double-acting cylinders at operating pressures to 700 bar.
• All gasoline engine/hydraulic pumps feature “Posi-Check®”valve to guard against pressure loss when valve is shiftedfrom “advance” to “hold”.
PG303 and PG304• Powered by a 2-cycle, 1.49 kW Tecumseh engine giving it
the lowest weight to kilowatt ratio of all gasoline drivenpumps. Has an aluminum reservoir with 6 liters of usableoil.
• Has same basic pump as PE30 series electric operatedpumps.
• PG30 series pumps are equipped with roll cages to protectpump from damage.
• PG30 series pumps weigh in at only 14.5 kg with oil.• PG303 is for single-acting cylinders, has a 9520 valve with
separate internal return line; allows oil from running pumpto return to reservoir, independently of cylinder return oil,when valve is in “return” position.
• PG304 is for double-acting cylinders, has a 9506 4-way(tandem center) valve.
PG553 and PG554• 4.47 kW Intek “Diamond Edge” 4-cycle, powered by a
Briggs & Stratton engine. Has a 19 liter reservoir.• Same basic pump as our PE55 series electrical powered
Vanguard® pumps.• PG553 has a 9520 3-way valve for single-acting cylinders.• PG554 has a 9506 4-way valve for double-acting
cylinders.
PG303
PG554
PERFORMANCE
Hoses, Fittings& GaugesPages74-80
Cylinder/PumpSpeed/SelectionChart Page178
PumpAccessoriesPages161-165
Choosing TheRight PumpPages181-184
E
A
D
CB
F
®
67www.powerteam.com
PUMPS
1.49 kW pump with 7.6 liter reservoir andsingle-acting valve.
4.47 pump with 21.6 liter reservoir andsingle-acting valve.
Advance HoldReturn
ValveType No. Function
Reservoir(Usable)
OrderNo.
PG303 3-Way 6 liters
PG553 20.8 liters**
9520
3-Way 9520
Advance HoldReturn
Description
ORDERING INFORMATION
See current price list for shipping weights.
SINGLE-ACTING
PG303, except has double-acting valve.
PG553, except has double-acting valve. Advance HoldReturn
ValveType No. Function
Reservoir(Usable)
OrderNo.
PG304 4-Way 6 liters
PG554 20.8 liters**
9506
4-Way 9506
Advance HoldReturn
Description
DOUBLE-ACTING
** Usable oil is calculated with oil fill at recommended level at 12.7 mm below cover plate
Kilowatts
1.49
4.47
Kilowatts
1.49
4.47
Cycle
2
4
Cycle
2
4
PG303 and PG304
PG553 and PG554
A
D
* First stage oil delivery from 0-28 bar @ 3.68 liters per minute minimum.
SPECIFICATIONS AND DIMENSIONSOil Delivery (liters/min.@) Dimensions (mm)Maximum Prod. Wt.
Pressure 7 70 350 700 With OilPump No. rpm Output bar bar bar bar A B C D E F (kg)
PG303, PG304 6,000 700 bar 4.4* 0.6 0.6 0.5 378 264 241 406 130 343 14.5PG553, PG554 3,600 700 bar 7.7 1.2 1.1 0.9 559 457 318 219 422 229 54.4
®
68 www.powerteam.com
PUM
PS
Gasoline Hydraulic Pumps2.1-6.4 L/min. — 4.1-14.9 kW (PG120-PG400 Series)
Maximum output gasoline powered pumps. Large reservoir capacity and equipped with rollcages. PG120 Series generally recommended for cylinders up to 300 ton. PG400 Seriesrecommended for cylinders up to 1,000 ton.
700 bar
• Two-speed high performance pumps ideal for construction,structure moving and rigging applications.
• A logical choice at work sites where electricity or compressed airare unavailable. For single- or double-acting cylinders atoperating pressures to 700 bar.
• All gasoline engine/hydraulic pumps feature “Posi-Check®” valveto guard against pressure loss when valve is shifted from“advance” to “hold”.
• PG1200 Series pumps powered by a Honda 4-cycle, 4.1 kWengine with automatic decompression and electronic ignition.Deliver over 2.1 liters of oil per minute at 700 bar.
• A 19 liter reservoir means adequate capacity for multi-cylinderapplications. Dual element air cleaner protects engine from dustyenvironments.
• Heavy duty “roll cage” provides pick-up points for lifting.Horizontal bars on PG1203, PG1204 and PG1204S protect unit,provide hand holds for carrying.
• Rubber anti-skid insulation on bottom of reservoir resistsskidding and dampens vibration. PG1200M-4 and PG1200M-4Dinclude a pump cart with 305 mm wheels.
• Adjustable external pressure regulator.PG1200M-4• For single-acting cylinders. Has 9520 3-way/3-position (tandem
center) valve, 9596 load lowering valve and 9644 4-port manifoldwith individual needle valves at each port.
• Has a 9796 coupler and 9797 dust cap at each port. Valvingpermits precise individual control of up to four cylinders.
• A 9052 heavy duty, fluid filled pressure gauge (0-700 bar) isincluded.
PG1200M-4D• For single- or double-acting cylinders with precise individual
control of up to four cylinders possible.• Equipped same as PG1200M-4, except has 9506 4-way/3-
position (tandem center) valve, and second 4-port manifoldwithout needle valves mounted beneath 9644 manifold foroperating double-acting cylinders.
PG400 Series Maximum output Hydraulic Power Package• Ideal for single or multiple cylinder applications. Has a
4-cycle, 14.9 kW Honda engine and 75.7 liter reservoir(62.8 liters usable) with low oil level sight gauge.
• Steel “roll cage” protects pump, has a lifting hook; 102 mm dia.swivel casters provide mobility.
• Delivers 6.4 liters of oil at maximum operating pressure.• Has a 9506 4-way valve. On/off switch and speed control are
protected by a panel. Sturdy molded case protects battery (notincluded).
PG1204S
PG1200M-4D
PG4004S
PERFORMANCE
Hoses, Fittings& GaugesPages74-80
Cylinder/PumpSpeed/SelectionChart Page178
PumpAccessoriesPages161-165
Choosing TheRight PumpPages181-184
®
69www.powerteam.com
PUMPSPG120HM PG1203, PG1204, PG1204S PG1200M-4 and PG1200M-4D PG4004
PG4004S
A
BC
D
E
FC
E
B D
A
FEB
FC
A
DB
A
SPECIFICATIONS AND DIMENSIONSOil Delivery (liters/min.@) Dimensions (mm)
Base model 4.1 kW gasoline pump with 21.6liter reservoir
PG1203 with cart, rollcage, load loweringvalve, 4 port manifold & gauge.
Advance HoldReturn**
ValveType No. Function
Reservoir(Usable)
OrderNo.
PG1203 3-Way 20.8 liters
PG1200M-4 20.8 liters
9520 Advance HoldReturn
Description
ORDERING INFORMATION
See current price list for shipping weights.
SINGLE-ACTING
Kilowatts
4.1
4.1
Cycle
4
43-WayManifold
95209644
PG1200M-4D, except without “Roll Cage” andcart. Ideal for house moving industry.
ValveType No. Function
Reservoir(Usable)
OrderNo.
PG120HM 20.8 litersAdvance HoldReturn**
Description
SINGLE & DOUBLE-ACTING
Kilowatts
4.1
Cycle
44-Way
Manifold95069642
Base model 4.1 kW gasoline pump, 21.6 literreservoir and double-acting valve.
PG1204, except has roll cage, cart, solenoidvalve and 7.6 meter cord.PG1200M-4, except for double-actingsystems.
Base model 14.9 kW pump with 75.7 literreservoir
PG4004, except has solenoid operatedremote valve.
Advance HoldReturn
ValveType No. Function
Reservoir(Usable)
OrderNo.
PG1204 4-Way 20.8 liters
PG1204S 20.8 liters
9506
9516
Advance HoldReturn
Description
DOUBLE-ACTING
* Usable oil is calculated with oil fill at recommended level at 57.2 mm below cover plate.** Control up to 4 cylinders independently.*** Has 7.6 meter remote control cord.
Kilowatts
4.1
4.1
Cycle
4
44-WaySolenoid***
PG1200M-4D 20.8 litersAdvance HoldReturn** 4.1 4
4-WayManifold
95069644
PG4004 62.8 liters*Advance HoldReturn 14.9 44-Way 9506
PG4004S 62.8 liters*Advance HoldReturn 14.9 4
4-WaySolenoid*** 9516
Maximum Prod. Wt.Pressure 7 70 350 700 With Oil
Pump No. rpm Output bar bar bar bar A B C D E F (kg)
PG120HM 3,600 700 bar 7.7 2.8 2.4 2.1 584 394 362 483 338 308 68PG1203,PG1204 3,600 700 bar 7.7 2.8 2.4 2.1 708 514 362 667 343 464 69.8PG1204S 3,600 700 bar 7.7 2.8 2.4 2.1 708 514 362 667 343 464 72.9PG1200M-4 3,600 700 bar 7.7 2.8 2.4 2.1 1070 457 635 1080 667 184 117.8PG1200M-4D 3,600 700 bar 7.7 2.8 2.4 2.1 1070 457 635 1080 667 184 126.8PG4004 3,600 700 bar 19.8 17.9 7.6 6.4 1276 1321 — — — — 197.1PG4004S 3,600 700 bar 19.8 17.9 7.6 6.4 1276 1321 — — — — 199.8
®70 www.powerteam.com
PUM
PS
The “Assemble to Order” SystemOrder a “Custom Built” hydraulic Pump
“Assemble to Order” means you can choose a basic pump with gas, air or electric motor.Then select the proper valve, gauge, pressure control, motor control and reservoir. We willassemble it, test it and ship it to you.
700 bar
Order a “custom built” hydraulic pump
“Assemble to Order” means you can choose a basic pump withgas, air or electric motor. Then select the proper valve, gauge,pressure control, motor control and reservoir. You get a two-stage pump that gives high oil volume for fast cylinderapproach (and return with double-acting cylinders) in the firststage and high pressure in the second stage.
.84 kW universal motor
These motors start under full load and are suitable for operationup to 350 or 700 bar. The motor is .84 kW, 12,000 rpm, 115 or230 volt (specify), 50/60 cycle A.C. single phase (13 amp drawat 220V.). With proper valve they can be used with single- ordouble-acting cylinders. Remote control available.
1.12 kW jet motor, single & three-phase
Feature low noise level, moderate speed for long service andare ideal for fixed applications. Motor is 1.12 kW, 2,850 rpm,220 volt, 50 cycle, A.C. single phase with thermal overloadswitch. Can be used with single- or double-acting cylinders andequipped with remote control. Also available in 230/460 volt,three-phase (specify).NOTE: These do not start under full load unless valve is in“neutral” (requires open or tandem center valve) and are notrecommended for frequent starting and stopping.
2.24 kW jet motor, three-phase
Gives low noise level and long life due to its moderate operatingspeed. Ideal for fixed installations. Consists of basic 700 barpump, jet pump motor: 2.24 kW, 2,850 rpm, 220/380 volt, 50cycle (specify). A.C. three-phase, with thermal overload switch.Equipped with internal and external relief valve. Will start underload.
2.24 kW air motor
This pump is ideal for use where electricity is unavailable orcannot be used. The 350 or 700 bar pump has a 2.24 kW airdriven motor at 3,000 rpm (optimum performance based on 6bar air pressure and 1.4 cu. m/min. at the pump). You candrive single- or double- acting cylinders with the correct valve.NOTE: 6 bar air supply required to start under full load.
Gasoline engine
This version is perfect when electricity and air are unavailable.It is capable of continuous operation at full pressure. Consistsof basic 700 bar pump, 4-cycle Briggs & Stratton “DiamondEdge” gasoline engine, developing 4.47 kW. As with all thesepumps, this unit can be valved for use with either single- ordouble-acting cylinders.
5
4
3
2
1
PG55A
5PE55APE55BPE90APE90B
1 PE55CPE55DPE55FPE90CPE90DPE90F
2 PA55APA90A
4
PE120M
3
“Assemble to Order” SystemHow to order your “Custom” hydraulic pump. . .
®
71www.powerteam.com
PUMPS
You can choose from pre-engineered, off-the-shelf componentsto customize your pump. All the components are listed in tableform, with key letters or numbers on pages 72-73. Complete
instructions guide you through so you can determine what isneeded to complete a pump assembly. Shown below is anexample of a custom-built pump.
9-126-74-52-31
1
8
BasicPump
PE55C50–
Valve &Valve Control
VV–Z–
Gauge & GaugeAccessories
G–A–
Pressure Control &Switch
A–A–
MotorControl
A–
Reservoir,Level/Temp
Gauge, Casters, Oil
D–BB–C–2F
9-126-74-52-31 8
Pump No. PE55C50–VV–Z–G–A–A–A–A–D–BB–C–2F is a 700bar two-speed pump with a 110 volt, 50 Hz, single phase, 1.12kW, 12,000 rpm motor; a 9512 4-way solenoid valve with a202778 remote hand control, a 9041 pressure gauge, no gaugeaccessories, standard pressure control, standard On-Off-Pulse
motor control, 40063OR9 7.6 liter reservoir, a 350431 oillevel/temperature gauge, 10494 casters, and 7.6 liters ofstandard hydraulic oil.
PERFORMANCE
21 3
4 5
See next two pages for pump components
®
72 www.powerteam.com
PUM
PS
The “Assemble to Order” SystemPump Component Specification Chart
3 VALVE CONTROL (See page 162)
2 VALVE (See pages 144-155)
1 BASIC PUMP (See pages 22-69)
* Suffixes AC, BC, CC & DC indicate pumps for Canadian orders only. NOTE:All electric units have 24 volt secondary circuit.
**Specify voltage required.
† These pumps do not start under full load unless valve is in “neutral” position(requires open or tandem center valve) and are not recommended forfrequent starting and stopping.
To buildyour
pump, fillin key letters
fromcharts
Use the charts numbered from 1-12 below to select the pump, valve,gauge and other miscellaneous accessories to suit your needs. For thepump, fill in the basic number plus key letter in block 1 above and the
key letter only in the blocks 2-12 above for any of the other items.Refer to the appropriate pages in this catalog for more specificinformation on the products you need.
▲▲
1 2 3 4 5 6
7 8 9 10 11 12
Valve Remote Control Use with ValveA None –X 304718 remote hand control, 3.1 m 9572XF 309652 remote foot control, 3.1 m 9572Y 202777 remote hand control, 3.1 m 9569 or 9599
Valve Remote Control Use with ValveZ 202778 remote hand control, 3.1 m 9512 or 9615
ZF 309653 remote foot control, 3.1 m 9512, 9615,9569 or 9599
ZZ 209593 remote hand control, 3.7 m 9594
Manifold/Manual/Air Operated Directional Valves FunctionAB 9628 manual, tandem center 4-way, 3 pos. AC 9632 manual “twin” tandem and open center valvesA None —B 9626 manifold ManifoldC 9584 manual 3-way,D 9582 manual 2 pos.E 9610 automatic, pilot operated valvesG 9504 manual 3/4-way,JJ 9594 air operated 2 pos. valvesL 9502 manual, closed center “non-interflow” 3-way,M 9520 manual, tandem center “Posi-Check®” 3 pos.N 9576 manual, metering tandem center valves
Manifold/Manual/Air Operated Directional Valves FunctionO 9609 manual, pressure compensated flow control 3-way, 4 pos.R 9506 manual, tandem center “Posi-Check®”
RR 9511 manual, open center 4-way,S 9500 manual, tandem center 3 pos.T 9507 manual, closed center “Posi-Check®” valvesU 9501 manual, closed center
Solenoid Operated Directional Valves FunctionFF 9569 solenoid operated - 24 volt 3-way, 2 pos.HH 9572 solenoid operated - 24 volt 3/4-way, 2 pos.PP 9599 solenoid operated - 24 volt 3-way, 3 pos.VV 9512 solenoid operated - 24 volt 4-way,
WW 9615 solenoid operated - 24 volt 3 pos. valves
BASIC PUMP NUMBERS SPECIFICATIONSPE55 PE90 PE120 PA55 PA90 PG55 NOTE: Customer must specify voltage required.
700 bar 350 bar 700 bar 700 bar 350 bar 700 bar Power Source rpm kW
A or AC* A or AC* 115V-60 Hz, 1Ø 12,000 .84110V-50 Hz, 1Ø 12,000 .84
B or BC* B or BC* 230V-60 Hz, 1Ø 12,000 .84220V-50 Hz, 1Ø 12,000 .84
† C or CC* † C or CC* 115V-60 Hz, 1Ø 3,450 1.12† C50 † C50 110V-50 Hz, 1Ø 2,850 1.12† D or DC* † D or DC* 230V-60 Hz, 1Ø 3,450 1.12† D50 † D50 220V-50 Hz, 1Ø 2,850 1.12† F60 ** † F60** 208, 230/460V-60 Hz, 3Ø 3,450 1.12† F50 ** † F50** 220/380V-50 Hz, 3Ø 2,850 1.12
M60 ** 208, 230/460V-60 Hz, 3Ø 3,450 2.24M50 ** 220/380V-50 Hz, 3Ø 2,850 2.24
A A Air Motor 3,000 2.24A Gas Engine 3,600 4.47
Select SelectBasic Select Valve Select Gauge PressurePump Valve Control Gauge Accessories Control
Pressure Motor Level/Temp Choose SelectSwitch Control Reservoir Gauge Casters Oil
®
73www.powerteam.com
PUMPS
NOTE: Includes cover adapter and misc. accessories when applicable.† High density polyethylene.‡ Aluminum.
NOTE: Select type of hydraulic oil and specify quantity.
4 GAUGE (See page 76-77)
6 PRESSURE CONTROL (See page 155)
NOTE: Pressure controls are factory pre-set at 700 bar unless otherwise specified.
5 GAUGE ACCESSORY (See page 76)
7 PRESSURE SWITCH (See page 163)
10 OIL LEVEL/TEMP. GAUGE (See page 164)
11 CASTERS (See page 164)
9 RESERVOIR (See page 165)
12 OIL (See page 78)
8 MOTOR CONTROL (See page 162)
Pressure GaugesA NoneB Other – SpecifyG 9041 0-10,000 psi – 0-689 Bar (63.5 mm dia.)H 9040 0-10,000 psi – 0-689 Bar (Liquid) (63.5 mm dia.)J 9051 0-10,000 psi – 0-689 Bar (102 mm dia.)K 9087 0-6,000 psi (102 mm dia.)M 9052 0-10,000 psi – 0-689 Bar (Liquid) (102 mm dia.)
Gauge AccessoriesA NoneN 9049 pulsation dampener – All dry gauges
Pressure SwitchA None
9625 electric pressure switch (35-700 bar)B NOTE: Pressure switch is factory pre-set at 700 bar
unless otherwise specified.C 9641 pilot operated air control valve – N.C.D 9643 pilot operated air control valve – N.O.
Pressure ControlsA With standard external pressure regulatorC Other – specify
D 350199 premium external pressure regulator. See Power Team Catalog product No. 9633 for details.
Reservoirs CapacityA None –B Other – Specify –D 40063OR9 – PE55, PE90, PE120, PA55
and PA90 series9.5 L
E 61165† – PE55, PE90, PE120, PA55 and PA90 series 7.6 L(Oil temperatures in excess of 65.5˚ C. may cause permanent failure of the thermoplastic reservoir)
F RP22‡ – PE55, PE90, PE120, PA55 and PA90 series
9.5 L
H 61799OR9 Same as D except with drain port
9.5 L
J RP50 – PE55, PE90, PE120, PA55 and PA90 series 19 L
K 40137OR9 – PG55 series 19 LP 209124 – PE55, PE90, PE120, PA55
and PA90 series 26.5 L
V RP100 – PE55, PE90, PE120, PA55 and PA90 series 37.9 L
W RP101 – PG55 series 37.9 L
Electric Motor Controls
Standard On/Off/Pulse control (does not include remote A switch) for A, B, C, D, F and M electric pumps. Also
used for remote controlled solenoid valves.B NoneC 25017 remote motor hand switch, 3.1 mD 203225 remote motor hand switch, 3.1 m (heavy duty)E 10461 remote motor foot switch, 3.1 m
Air Motor ControlsAA OtherB NoneP 27876 hand motor control (for PA55 & PA90 series)Q 27877 foot motor control (for PA55 & PA90 series)
Oil Level/Temperature GaugeA None
BB 350431 oil level/temperature gauge
CastersA None
C 10494 caster for use with 40063OR9 reservoir (Specify quantity of four)
OilE Ship pump without oilF 9637 3.8 L standard hydraulic oilG 9638 9.5 L standard hydraulic oilQ 9639 3.8 L Flame-Out hydraulic oilR 9640 9.5 L Flame-Out hydraulic oilU 9645 3.8 L biodegradable hydraulic oilV 9646 9.5 L biodegradable hydraulic oil
Recommended