View
29
Download
4
Category
Preview:
Citation preview
Publications No.
INSTALLATIONINSTRUCTIONS
Accessory Application
© 2011 American Honda Motor Co., Inc. – All Rights Re
AII 46393
REMOTE CONTROL ENGINE STARTERserved. AII 46393 (1108
2012 PILOT
) 0
Issue Date
AUG 2011
PARTS LIST
Remote Control Engine Starter Unit KitP/N 08E91-E22-101A
Transmitter
Control unit
Antenna
Key ring
Protective tape
Caution label
Fuse label
Accessory User’sInformation Manual
Quick start guide
Remote Control Engine Starter Attachment KitP/N 08E92-SZA-100
Engine starter harness
Control unit bracket
Template
2 Relays
Flange nut
1 of 218E92-SZA-1000-91
Ground bolt
16 Wire ties
Long wire tie
5 Urethane tapes
TOOLS AND SUPPLIES REQUIRED
Flat-tip screwdriver
Phillips screwdriver
Small flat-tip screwdriver
Ratchet
8 mm and10 mm Sockets
Combination wrench
Isopropyl alcohol
Shop towel
Tape measure
Scissors
Small rubber mallet
Honda Diagnostic System (HDS)
Masking tape
Needle nose pliers
Plastic trim tool T/N SILTRIMTL 10
2 of 21 AII 46393
Illustration of the Engine Starter Installed in the Vehicle
INSTALLATION
NOTE: This antenna should be installed only if the ambient air temperature is 15°C (60°F) or above.
1. Make sure you have the anti-theft code for the audio unit, then write down the radio station presets.
2. Disconnect the negative cable from the battery.
Customer Information: The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by “do-it-yourselfers.”
792001AY
FUSE CASES (3A, 3A, 40A)
ENGINE STARTER HARNESS
ANTENNA
CONTROL UNIT
(1108) © 2011 American Honda Motor Co., Inc. – All Rights Reserved.
Setting the Control Unit
3. Touch the metal part of the screwdriver to any metal part of the vehicle to discharge any static electricity.
4. Check the settings of the switches on the control unit.
NOTE:
• The switches must be set before the control unit is plugged in.
• If a switch setting is not correct, the remote engine starter will not operate properly.
• If you change the switch settings with the unit connected, you must disconnect the unit, then reconnect it before the new settings are recognized.
5. Using a small flat-tip screwdriver, set the switches on the control unit as shown.
7D2550AK
CONTROL UNIT
SMALL FLAT-TIP SCREW-DRIVER
Discharge any static electricity.
SET
SWITCHES
SW:1 RR Junction unit -----------------------> OFF
SW:2 Trunk or Tailgate ----------------------> OFF
SW:3 Smart Entry -----------------------------> OFF
SW:4 Horn or Buzzer Answerback ------> OFF
SW:5 Trunk Main SW -------------------------> OFF
SW:6 Reserve ----------------------------------> ON
SWITCHES
© 2011 American Honda Motor Co., Inc. – All Rights Reserved. AII 46393
6. Using isopropyl alcohol on a shop towel, clean the area where the protective tape will attach. Remove the adhesive backing from the protective tape, and attach the protective tape to the control unit over the switches.
Removing the Vehicle Parts
7. Using a plastic trim tool, disengage the eight retaining tabs and remove the left and right lenses from the roof console.
772505AS
CONTROL UNIT
SWITCHESPROTECTIVE TAPE
ADHESIVE BACKING
Clean with isopropyl alcohol.
700602BB
ROOF CONSOLE
RIGHT LENS
4 RETAINING TABS
LEFT LENS
4 RETAINING TABS
PLASTIC TRIM TOOL
(1108) 3 of 21
8. Open the sunglass holder.
9. Remove the roof console (two black screws, two silver screws, and unplug the vehicle connectors).
10. Rotate the two sunvisor holders 45°, then remove them.
700603BB
ROOF CONSOLE
SUNGLASS HOLDEROpen.
VEHICLE CONNECTOR
2 SCREWS(Black) 2 SCREWS
(Silver)
700215BE
SUNVISOR HOLDER
Turn.
SUNVISOR HOLDERS
4 of 21 AII 46393
11. Pivot down the left sunvisor.
12. Locate the slot in the sunvisor holder, and insert a flat-tip screwdriver into the slot. Push in and hold the retaining tab.
13. While holding the retaining tab, push up on the left sunvisor and rotate it towards the door to remove the sunvisor. Unplug the vanity mirror light connector.
If the retaining tab did not stay pushed in, return the left sunvisor to its original position and repeat steps 11 through 13.
840902AY
LEFT SUNVISORTurn rearward.
Push upward.
FLAT-TIPSCREWDRIVER
HOLDER
Push and hold the retaining tab.
Rotate towards the door.VANITY
MIRROR LIGHT CONNECTOR
(1108) © 2011 American Honda Motor Co., Inc. – All Rights Reserved.
14. Using a plastic trim tool, open the lid in the left A-pillar trim (two retaining tabs).
15. Remove the bolt from the left A-pillar trim.
16. Pull away the weatherstrip and remove the left A-pillar trim (one clip).
17. Pull off the weatherstrip, then remove the left side dashboard cover (seven retaining tabs).
792203AE
LEFT A-PILLAR TRIM
LIDRETAINING TABS
BOLT
CLIP
WEATHERSTRIP Pull away.
LEFT A-PILLAR TRIM
792403CE
LEFT SIDEDASHBOARD COVER
7 RETAINING TABS
WEATHERSTRIPPull away.
© 2011 American Honda Motor Co., Inc. – All Rights Reserved. AII 46393
18. Move the shift lever to D by pressing down on the shift lock release with the ignition key. Remove the left side center panel (eight clips and unplug the vehicle connectors).
19. Remove the driver’s dashboard lower cover (12 clips, one self-tapping screw and unplug the vehicle connectors). Remove the A/C sensor (two retaining tabs).
792808AE
LEFT SIDE CENTER PANEL
VEHICLE CONNECTOR
IGNITION KEY SHIFTLEVER
8 CLIPS
VEHICLE CONNECTOR(If equipped)
792205CE
12 CLIPS
SELF-TAPPING SCREW
DRIVER’S DASHBOARD LOWER COVER
A/C SENSORVEHICLE CONNECTOR
A/C SENSOR2 RETAINING TABS
(1108) 5 of 21
20. Lower the tilt lever and pull the steering wheel out.
21. Remove the upper steering column cover:
• Remove the two self-tapping screws.
• Push the upper cover inward at the areas shown to release the four retaining tabs.
22. Remove the lower steering column cover (two self-tapping screws and one screw).
792404CE
UPPER STEERING COLUMN COVER
SELF-TAPPING SCREWS
TILT LEVER
Push.
4 RETAINING TABS
792405AE
LOWER STEERING COLUMN COVER
SELF-TAPPING SCREWSSCREW
6 of 21 AII 46393
Routing the Engine Starter Harness
23. Attach the 40A fuse label to the engine starter harness fuse block at the position shown.
24. Attach the 3A fuse label to the engine starter harness fuse block at the position shown.
25. Install the two relays to the engine starter harness relay blocks.
840903AY
ENGINE STARTER HARNESS
FUSE BLOCK
FUSE LABEL (3A)
FUSE LABEL(40A)
792003BY
ENGINE STARTER HARNESS
RELAY BLOCK
RELAYS
(1108) © 2011 American Honda Motor Co., Inc. – All Rights Reserved.
26. Plug the engine starter harness 28-pin connector into the control unit.
27. Install the control unit bracket to the control unit.
792004AY
CONTROL UNIT
28-PIN CONNNECTOR
ENGINE STARTER HARNESS
792005AY
CONTROL UNIT
CONTROL UNIT BRACKET
© 2011 American Honda Motor Co., Inc. – All Rights Reserved. AII 46393
28. Secure the control unit to the vehicle bracket with a 6 mm flange nut.
792401CY
FLANGE NUT, 6 mm
CONTROL UNIT
STEERING SHAFT
STEERING WHEEL
CONTROL UNIT
STEERING SHAFT
VEHICLE BRACKET
CONTROL UNIT BRACKET
VEHICLE BRACKET
Hold against the brackets.
(1108) 7 of 21
29. Install the engine starter harness fuse block clip on the control unit bracket.
30. Install the engine starter harness clip on the vehicle bracket.
792402AY
ENGINE STARTER HARNESS
CONTROL UNIT BRACKETFUSE BLOCK
CLIP
792403AY
ENGINE STARTER HARNESS
VEHICLE BRACKET
CLIP
8 of 21 AII 46393
31. Route the engine starter harness relay block toward the right side of the vehicle.
32. Install the engine starter harness relay block on the vehicle relay block.
33. Remove the blue tape from the vehicle 4-pin connector. Plug the engine starter harness 4-pin connector to the vehicle 4-pin connector.
792404AY
ENGINE STARTER HARNESS
VEHICLE RELAY BLOCK
RELAY BLOCK
792501AY
ENGINE STARTER HARNESS
4-PIN CONNECTOR
BLUE TAPERemove.
VEHICLE 4-PIN CONNECTOR(White)
STEERING WHEEL
(1108) © 2011 American Honda Motor Co., Inc. – All Rights Reserved.
34. Secure the 4-pin connector to the vehicle harness with one wire tie.
35. Align the green-tape on the engine starter harness with the vehicle clip. Secure the engine starter harness to the vehicle harness with one wire tie.
792502AY
WIRE TIE
VEHICLE HARNESS
4-PIN CONNECTORS
792503BY
WIRE TIEVEHICLE HARNESS
ENGINE STARTER HARNESS
VEHICLE CLIP
GREEN TAPE
FUSE BOX
© 2011 American Honda Motor Co., Inc. – All Rights Reserved. AII 46393
36. Locate and remove the blue tape from the vehicle 2-pin connectors (white), and unplug the vehicle 2-pin connectors as shown.
37. Plug the engine starter harness 2-pin connectors to the vehicle 2-pin connectors as shown.
38. Route the engine starter harness 2-pin connectors behind the fuse box as shown.
7D0701BESTEERING SHAFT
VEHICLE 2-PIN CONNECTORS(White)FUSE BOX
BLUE TAPE
792706BY
ENGINE STARTER HARNESS
2-PIN CONNECTORS
VEHICLE 2-PIN CONNECTORSFUSE
BOX
STEERING SHAFT
(1108) 9 of 21
39. Secure the 2-pin connectors to the vehicle harness with one wire tie.
40. Cut a urethane tape into two equal parts, and cut a 10 mm piece from one part, as shown.
41. Clean the vehicle bracket surface with isopropyl alcohol where the urethane tape will attach. Attach the 10 mm piece of urethane tape to the vehicle bracket as shown.
792707EY
VEHICLE HARNESS
WIRE TIE 2-PIN CONNECTORS
ENGINE STARTER HARNESS
FUSE BOX
STEERING SHAFT
7D2401AB
PARKING BRAKE LEVER
VEHICLE BRACKET
URETHANE TAPE
10 mm
URETHANE TAPE
10 of 21 AII 46393
42. Route the engine starter harness ground terminal as shown.
43. Remove the vehicle bolt near the parking brake lever, and discard it. Install the engine starter harness ground terminal with the ground bolt from the kit.
44. Secure the engine starter harness to the vehicle harness with two loosely installed wire ties.
792708BY
VEHICLE BOLTDiscard.
ENGINE STARTER HARNESS GROUND TERMINAL
PARKING BRAKE LEVER
FUSE BOX
GROUND BOLT
792709BY
WIRE TIESLoosely installed.
ENGINE STARTER HARNESS VEHICLE
HARNESS
(1108) © 2011 American Honda Motor Co., Inc. – All Rights Reserved.
45. Route the engine starter harness 5-pin connector to the ignition switch.
46. Unplug the vehicle 12-pin connector, and plug it into the engine starter harness 12-pin connector. Plug the remaining engine starter harness 12-pin connector into the turn signal switch.
792601BY
ENGINE STARTER HARNESS
IGNITION SWITCH
5-PIN CONNECTOR
792701AY
VEHICLE 12-PIN CONNECTOR
BODY SWITCH
12-PIN CONNECTORS ENGINE
STARTER HARNESS
TURN SIGNAL SWITCH
© 2011 American Honda Motor Co., Inc. – All Rights Reserved. AII 46393
47. Unplug the vehicle 8-pin connector, and plug it into the engine starter harness 8-pin connector. Plug the remaining engine starter harness 8-pin connector into the wiper switch.
48. Route the engine starter harness into the harness case.
792702AY
8-PIN CONNECTORS
VEHICLE 8-PIN CONNECTOR
BODY SWITCH
ENGINE STARTER HARNESS
WIPER SWITCH
792703AY
HARNESS CASE
ENGINE STARTER HARNESS
FRONT
(1108) 11 of 21
49. Secure the 12-pin and 8-pin connectors to the harness case with two wire ties.
792704BY
FRONTENGINE STARTER HARNESS
HARNESS CASE
WIRE TIES
8-PIN CONNECTORS
12-PIN CONNECTORS
12 of 21 AII 46393
50. Unplug the vehicle 5-pin connector from the ignition switch, and plug the engine starter harness 5-pin connector into the ignition switch.
51. Plug the engine starter harness 5-pin connector into the vehicle 5-pin connector.
NOTE: Make sure the engine starter harness 5-pin connector is connected securely. A loose connection can cause engine stalling.
52. Wrap one urethane tape around the 5-pin connectors.
792602CY
Connector unlock
Push.Pull.
Push.
Connector lock
12
31
2
VEHICLE 5-PIN CONNECTOR
5-PIN CONNECTOR
ENGINE STARTER HARNESS
URETHANE TAPE
5-PIN CONNECTOR
5-PIN CONNECTOR
(1108) © 2011 American Honda Motor Co., Inc. – All Rights Reserved.
53. Secure the 5-pin connectors in between the vehicle harness and the engine starter harness with one long wire tie.
54. Unplug the vehicle 7-pin connector from the ignition switch, and plug the engine starter harness 7-pin connectors to the ignition switch and to the vehicle 7-pin connector.
792603DY
5-PIN CONNECTOR
VEHICLE HARNESS
LONG WIRE TIE
ENGINE STARTER HARNESS
5-PIN CONNECTORVEHICLE
HARNESS
LONG WIRE TIE
CROSS SECTION
792604DY
VEHICLE 7-PIN CONNECTOR
IGNITION SWITCH
7-PIN CONNECTOR ENGINE
STARTER HARNESS
7-PIN CONNECTOR
© 2011 American Honda Motor Co., Inc. – All Rights Reserved. AII 46393
55. Secure the engine starter harness to the vehicle harness with one wire tie as shown.
56. Adjust the steering wheel in, out, up, and down while you check the engine starter harness routing. If the harness is rubbing against the steering column bracket, check the installation and position of the wire ties installed in steps 53 and 55.
792705CY
ENGINE STARTER HARNESS
VEHICLE HARNESS
IGNITION SWITCH
WIRE TIE
(1108) 13 of 21
Antenna Installation
57. Using two needle nose pliers, bend the antenna plate according to the drawing shown,
58. Starting at the antenna end of the cable, wrap three urethane tapes around the antenna cable at the measurements shown.
792710AY
ANTENNA
PLATE
13 mm
8 mm
SCALE
NEEDLE NOSE PLIERS
701015AB
ANTENNA
40 mm
40 mm
410 mm
ANTENNA CABLE
URETHANE TAPE
14 of 21 AII 46393
59. Using scissors, cut out the template.
60. Align the template with edge of the black ceramic paint as shown, then secure the template to the windshield with masking tape.
7209041K
Cut out.TEMPLATE
Cut out.
6N3002AK
BLACK CERAMIC PAINT
FRONT WINDOW
MASKING TAPESTEMPLATE
MIRROR
(1108) © 2011 American Honda Motor Co., Inc. – All Rights Reserved.
61. Using isopropyl alcohol on a shop towel, clean the area where the antenna will attach. Allow to dry before proceeding.
62. Remove the adhesive backing from the antenna, insert the antenna plate behind the headliner, and attach the antenna to the windshield.
63. Remove the template.
64. Route the antenna cable to the left side of the vehicle, and push it behind the headliner as shown. Be careful not to crease the headliner.
6N3004BK
TEMPLATE
HEADLINER
ADHESIVE BACKINGANTENNA
PLATE
6N30050K
ANTENNA CABLE
HEADLINER
© 2011 American Honda Motor Co., Inc. – All Rights Reserved. AII 46393
65. Clean the vehicle panel surface with isopropyl alcohol where the urethane tape will attach. Secure the antenna cable to the vehicle panel with one half of the urethane tape that you cut into two in step 40. Be careful not to crease the headliner.
66. Clean the vehicle panel surface where the urethane tape will attach with isopropyl alcohol. Secure the antenna cable to the vehicle panel with the remaining part of the urethane tape you cut in step 40. Be careful not to crease the headliner.
701016BB
ANTENNA CABLE
VEHICLE PANEL
URETHANE TAPE
1/2 of urethane tape cut in step 40.
HEADLINER
URETHANE TAPE
701017BB
ANTENNA CABLE
VEHICLE PANEL
URETHANE TAPE
Leftover urethane tape from step 40.
HEADLINER
(1108) 15 of 21
67. Route the antenna cable along the left A-pillar. Secure the antenna cable to the vehicle harness with four wire ties as shown.
68. Secure the antenna cable to the vehicle harness with one wire tie.
792711AY
ANTENNA CABLE
VEHICLE HARNESS
WIRE TIES
LEFT A-PILLAR
700101AY
ANTENNA CABLE
VEHICLE HARNESS
WIRE TIE DRIVER’S DASHBOARD COVER OPENING
16 of 21 AII 46393
69. Route the antenna cable along the engine starter harness. Secure the antenna cable to the vehicle harness with the two wire ties that were loosely installed in step 44.
70. Route the antenna cable terminal toward the right side of the vehicle, and plug it into the control unit as shown.
700102BY
ANTENNA CABLE
VEHICLE HARNESS
WIRE TIES
FUSE BOX
700103AY
ANTENNA CABLE
CONTROL UNIT
ANTENNA CABLE TERMINAL
(1108) © 2011 American Honda Motor Co., Inc. – All Rights Reserved.
71. Secure the engine starter harness and antenna cable with one wire tie as shown.
72. Bundle the excess antenna cable. Secure the antenna cable to the engine starter harness with two wire ties.
73. Using isopropyl alcohol on a shop towel, clean the hood where the caution label will attach.
74. Attach the caution label to the hood in the area shown.
75. Check that all wire harnesses and cables are routed properly and that all connectors are plugged in.
76. Reinstall all removed parts. Check that all clips and other fasteners are installed securely.
700104AY
ENGINE STARTER HARNESS
ANTENNA CABLE
WIRE TIE
WIRE TIES ANTENNA CABLE Bundle the excess.
7D0702AE
HOOD
CAUTION LABEL
ADHESIVE BACKING
© 2011 American Honda Motor Co., Inc. – All Rights Reserved. AII 46393
77. Reconnect the negative cable to the battery. Check that the electrical accessory and other electrical systems function properly.
78. Enter the customer’s audio unit anti-theft code and reset the radio station presets.
79. Reset the clock on models without navigation.
80. Do the “REMOTE ENGINE STARTER REGISTRATION” and “FUNCTION CHECK.”
REMOTE ENGINE STARTER REGISTRATION
1. Acquire the PCM code from the Interactive Network.
2. Connect the HDS tester to the OBD II data link connector, then turn the ignition switch to ON (II).
3. Turn on the HDS, and click the car icon.
4. Input the VIN and other required information into the HDS, then click the check button.
CAR ICON
752502AS
CHECK BUTTONInput the VIN and other required information.
(1108) 17 of 21
5. Select Honda Systems, then click the check button.
6. Select R/C ENG STARTER, and click the check button.
752503AS
CHECK BUTTONSelect “Honda Systems.”
752504AS
CHECK BUTTONSelect “R/C ENG STARTER.”
18 of 21 AII 46393
7. A REMARKS message will display. Click on the check button.
8. Select REGISTER REMOTE CONTROL ENGINE STARTER UNIT, then click the check button.
752505AS
CHECK BUTTON
“REMARKS” message
752506AS
CHECK BUTTONSelect “REGISTER REMOTE CONTROL ENGINE STARTER UNIT.”
(1108) © 2011 American Honda Motor Co., Inc. – All Rights Reserved.
9. The following message will display: Obtain PCM-code (IMMOBILIZER PCM CODE) from iN. This vehicle’s VIN will be required to obtain the password. (USA). Click on the check button.
10. Input the PCM code, then click the check button.NOTE: To ensure security, the PCM code (password) is changed everyday, so it is impossible to register the remote control engine starter if the dates of the PCM code acquisition and registration are different. The date of the HDS tester should also match.
752507AS
CHECK BUTTON
“Obtain PCM-code” message
752509AS
CHECK BUTTON
Input the PCM Code.
© 2011 American Honda Motor Co., Inc. – All Rights Reserved. AII 46393
11. The following message will display: The registration of the Remote Control Engine Starter Unit has been completed. Click on the check button.
12. The following message will display: Check that the engine can be started by the Transmitter. Click on the check button.
13. Perform the “FUNCTION CHECK” on the next page, then disconnect the HDS.
752510AS
CHECK BUTTON
“The registration of the Remote Control Engine Starter Unit has been completed”.
752511AS
CHECK BUTTON
“Check that the engine can be started by the Transmitter”.
(1108) 19 of 21
FUNCTION CHECK
Operating Conditions
• Hood is closed.
• Shift lever is in park.
• The key is not in the ignition switch.
• All doors and tailgate are closed and locked.
Inspection
1. Press the command button on the transmitter and, within 1 second,
press the start button. The engine should start if all operating conditions are met.Does the engine start?
2. Press the command button on the transmitter and, within 1 second, press the stop button. The engine should stop.
Does the engine stop?
3. After the engine has stopped, start the engine again, and check that the engine stops after each of the following conditions:
Yes - Operation is normal.
No:• Make sure all operating conditions are met.• Check the engine starter harness connections.• Connect the HDS and check for an indicated failure.
(Refer to the appropriate service manual for details.)
Yes - Operation is normal.
No - Check the engine starter harness connections.
NOTE: After each test the ignition key must be cycled, or the driver’s do
20 of 21 AII 46393 (1108)
732904AY
DISPLAY
STOP BUTTON
COMMAND BUTTON
START BUTTON
TRANSMITTER
or must be opened and closed
• Move the shift lever out of the P position.
• Unlock or open the doors or the tailgate.
• Open the hood.
• Insert the key in the ignition switch.
• Press on the brake pedal.
Does the engine stop after each of these tests?
4. Check that the power windows and the moon roof do not function when the engine is started with the transmitter.
5. Press the command button on the transmitter two times and check the vehicle condition on the display.
6. Check the operation of the transmitter when the vehicle is 100 m to 150 m (325 to 490 ft.) away, and in direct sight.
Yes - Operation is normal.
No - Check the engine starter harness connections.
© 2011 American Honda Motor Co., Inc. – All Rights Reserved.
How to Program an Additional Transmitter
1. Connect the HDS to the data link connector.
2. Start the HDS and click on the car icon.
3. Input the vehicle’s VIN and other required information.
4. Select Honda Systems.
5. Select R/C Engine Starter.
6. Select REGISTER NEW TRANSMITTER.
7. When “Ready to program the new transmitter” shows, select ENTER.
8. Press and release the Command button.
9. Press and release the Stop button.
10. Perform the function check on both transmitters.
NOTE: Only 2 remotes can be stored in the system’s memory.
© 2011 American Honda Motor Co., Inc. – All Rights Reserved. AII 46393
(1108) 21 of 21Recommended