View
7
Download
0
Category
Preview:
Citation preview
FEATURESH-series gear units have been designed to be highly reliable even under heavy working conditions, and are
particularly suited for applications involving high radial loads. The H-series includes a large number of extremely
versatile models, available in cast iron from size 030 to size 140 and in aluminium from size A30 to size A60.
HSERIES
• Casing with feet, flange F or universal U
• Gearing with 1, 2 and 3 reduction stages
• Gears hardened and tempered with shaved or
ground profile
• Cases in G200 grey cast iron for high strength and
optimized with FEM analysis
• Excellent mechanical strength, particularly suitable
to support high axial loads and high reliability
• Load capacity calculated to ISO6336 and verified
according to AGMA 2001
• Painted with RAL 5010 blue epoxy-polyester powder
• ATEX versions available 2GD/3GD
• Accessories: output flange, backstop device,
reinforced seals on output shaft and viton seals
H - PHFitted for motor coupling -Coupling with flexiblecoupling
CHWith compact motor
IHWith input shaft
SIZES:030-040-050-060-080-100-125-140
CAST IRON
HAFitted for motor coupling
CHAWith compact motor
IHAWith input shaft
SIZES:A30-A40-A50-A60
ALUMINIUM
• Casing with feet, flange F or universal U
• Gearing with 1, 2 and 3 reduction stages
• Gears hardened and tempered with shaved or ground
profile
• Cases in die-cast aluminium alloy
• Excellent mechanical strength while being and
particularly lightweight
• Load capacity calculated to ISO6336 and verified
according to AGMA 2001
• Painted with RAL 5010 blue epoxy-polyester powder
• ATEX versions available 3GD
RANGE HSERIES
• Power from 0,12 kW up to 45 kw
• Reduction ratios between 1,23 and 282,10
• Nominal torque 8.000 Nm
• Admissible radial loads max 55.000 N
• Power from 0,12 kW up to 4.8 kw
• Reduction ratios between 1,33 e 353,98
• Nominal torque 480 Nm
• Admissible radial loads max 8.000 N
Ø [mm]
OutputTorque M
2 [Nm]
Ratio(i)
Max Min Max
H030 25 200 4,70 245,70
H040 19-30 300 1,44 282,10
H050 24-35 500 1,27 267,65
H060 28-35-40 850 1,34 268,00
H080 38-40-50 1.800 1,30 222,78
H100 48-60 3.600 1,29 242,59
H125 55-70 5.000 1,23 230,92
H140 90 8.000 5,27 206,08
Ø [mm]
OutputTorque M
2 [Nm]
Ratio(i)
Max Min Max
HA30 11-14-16-19-19,7-20 100 5,38 347,29
HA40 16-19-20-22-24-25-28 150 1,45 347,29
HA50 24-25-28-30-32-35 300 1,45 353,98
HA60 24-28-30-35-40 480 1,33 353,98
NEW• Reinforced input flanges for big cast iron motors
• Increased torsional rigidity thanks to the new cast iron inspection cover
• Metal plate for aggressive environments
• Oil-free gearbox to allow the most suitable choice of lubricant for every application requirement
Viscosity index
n2(rpm)
Mineral oil Synthetic oil
0 ÷ +40 [°C] -10 ÷ +50 [°C]
> 210 150 150
210 ÷ 20 150 220
20 ÷ 5 220 320
< 5 320 460
CAST IRON VERSIONS
HR...SINGLE STAGEFoot mounting
HSERIES
HR...F SINGLE STAGEFlange mounting
HR...M SINGLE STAGEFoot mounting with low output shaft centre
HR...U SINGLE STAGEFoot/flange mounting
H... 2/3 STAGESFoot mounting
H...F 2/3 STAGESFlange mounting
H...U 2/3 STAGESFoot/flange mounting
ALUMINIUM VERSIONS
HA.. SINGLE STAGEFoot mounting
HSERIES
HA..F SINGLE STAGEFlange mounting
HA.. 2 STAGESFoot mounting
HA.. 3 STAGESFoot mounting
HA..F 2 STAGESFlange mounting
HA..F 3 STAGESFlange mounting
HA..U 2/3 STAGESFoot/flange mounting
Recommended