View
2
Download
0
Category
Preview:
Citation preview
Features
• 13,6 t (15 USt) capacity
• 12,5 m (41 ft) three-section, full-power synchronized boom
• 9,1 t (10 USt) deck carrying capacity
• Load sensing piston pump with hydraulic proportional controls
Grove YB5515-2Product GuideASME B30.5Imperial 85%, Metric 85%, DIN/ISO
Features
The reach and capacity to get the job done The standard three-section boom offers 4,6 m – 12,5 m (15 ft – 41 ft) of reach with a max tip height of 14,2 m (46.5 ft). The optional four-section boom offers 5,4 m – 15,4 m (17.8 ft – 50.0 ft) of reach that can be enhanced with the optional 4,6 m (15 ft) swingaway extension to provide a total max tip height of 20,4 m (67 ft).
OutriggersThe YB5515-2 outriggers are two-position (0˚ and 100˚) beam/jack style outriggers with inverted jack cylinders and pivoting pad.
Operator cabNew operator control layout with
hydraulic proportional joystickcontrols, tilt steering wheel, and automotive
dash panel gauges and indicator lights.
SteeringThe YB5515-2 comes standard with three steering modes: front (two-wheel), four-wheel coordinated, and four-wheel crab steer with electronic self alignment. Operators can choose between modes via three-position rocker switch located on dash panel.
Contents
Specifications 4
Dimensions and weights 7
Working ranges and load charts (imperial) 9
Working ranges and load charts (metric) 15
Working ranges and load charts (DIN/ISO) 21
Transport and lifting data 27
Rigging chart 28
Symbols glossary 29
4
Specifications
*Denotes optional equipment
Superstructure
Boom
4,6 m – 12,5 m (15 ft – 41 ft) three-section, full-power, synchronized, telescopic boom.Maximum tip height: 14,2 m (46.5 ft)
*Optional boom extensions
4,6 m (15 ft) fixed swingaway extension
Maximum tip height with standard boom: 18,1 m (59.5 ft)
Maximum tip height with optional boom: 20,4 m (67 ft)
Boom extension can be offset 0˚, -15˚, and -30˚ via pivoting boom nose on the optional boom.
Boom nose
Fixed two-sheave quick reeve boom nose with standard 12,5 m (41 ft) boom. Two-sheave, quick reeve type with-3- pinned pivoting (0˚, +40˚, and +80˚) boom nose design to minimize head space requirements. With optional boom only.Lowers head height 0,4 m (1.3 ft) when nose ispivoted fully forward.
Boom elevation
Single double acting hydraulic cylinder with integral holding valve. Elevation: 0˚ to 69˚
Anti-two block device
Standard anti-two block device (hardwired), which, when activated, provides an audible and visual warning to the operator and “locks out” all functions whose movement can cause two-blocking.
Load Moment Indicator
A simple, effective, and easy to use load moment indicating system used in conjunction with the anti-two block system to assist the operator in efficient operation of the unit within the limits of the load chart. The display panel displays the max. load allowed, the actual hook load, length and angle of the boom, and load radius in Dot Matrix numerical values and provides a load utilization colored bar graph. Inputs by operator are maximum allowed load and parts of line. If non-permitted conditions are approached the L.M.I. will warn the operator with an audible alarm and a warning light and will lock out those functions that may aggravate the condition.
* Optional Load Moment Indicator
“Graphics Display” of boom angle, boom length, loadradius, and capacity. Operator input to set the limitparameters based on the load chart. Displays colorcoded light bar and audible alarm with function cut-outif load exceeds the load chart parameters.
Swing
Ball bearing swing circle with 360˚ continuous rotation. Worm gear and pinion driven by hydraulic motor. Spring applied, hydraulic released brake. Equipped with swing enable control.Maximum speed: 2.5 rpm
Hydraulic system
One pressure compensated variable displacement axial piston pump, with load sensing.Maximum output of: 155 LPM (41.0 GPM) Maximum operating pressure: 276 bars (4000 p.s.i.)
Four section valve bank, chassis mounted, operated via dash mounted pilot pressure hydraulic joystick controllers.
140L (37 gal) steel hydraulic reservoir with sight level gauge and steel side plating to guard against side impact.
Return line replaceable filter with by-pass protection and service indicator. Cartridge filter rating of 3 micron.
*Optional Boom
5,4 m – 15,4 m (17.8 ft – 50 ft) four-section, full-power, synchronized, telescopic boom.Maximum tip height: 16,5 m (54 ft)
Grove YB5515-2 5
Specifications
*Denotes optional equipment
Hoist specifications
Two speed gear motor driven hoist with automaticspring applied / hydraulically released wet brake.Smooth drum with cable follower.
Maximum hoist pull (first layer): 63,6 kN (14,300 lb)
Maximum permissible single line pull:44,5 kN (10,000 lb.) (3.5:1 design factor)
Maximum single line speed: 64 m/min (210 fpm)
Rope construction: 6 x 19 XXIPS / IWRC
Rope diameter: 14 mm (9/16 in)
Rope length: 97,5 m (320 ft)
Carrier
Chassis
High strength alloy frame constructed with integral outrigger housings; front and rear lifting, tie-down, and towing lugs. 6,2 m2 (66.3 sq ft) carry deck size with 9072 kg (20,000 lb) deck only carrying capacity. Deck coated with anti-skid treatment.
Outriggers
Single stage hydraulic telescoping beam with oblique style jack cylinder on all four corners. Provides extended and down and retracted and down lifting capabilities.Integral holding valve on both beam and jack.Outrigger positioning indicator located in dash display.
Outrigger pad size: 222 mm x 254 mm (8.75 in x 10 in)
Maximum outrigger pad load: 15 876 kg (35,000 lb)
Outrigger controls
Independent outrigger control rocker switches for beam or jack selection with a separate extend /retract rocker selector switch. 360˚ level bubble located inside cab.
Fuel tank capacity
Steel with side impact plate. Capacity: 151.4L (40 gal).
Operators control station
Frame mounted, open air style control station with cab shell includes all crane functions and driving controls and equipped with overhead safety glass. Other standard equipment includes a suspension seat with seat belt, sight level bubble and 1,1 kg (2.5 lb) fire extinguisher, and tilt steering wheel. The dash panel will display the fuel level gauge, water temperature gauge, engine rpm, battery voltage, and hour meter. Indicator lights will display parking brake, low transmission pressure, low brake pressure, outrigger position, headlights, work lights (if ordered), and hoist 3rd wrap (if ordered). Crane function indicator and turn signal indicators are also included. The load indicator display will be mounted on the top of the dash panel for direct line of sight for the operator.
Engine (Tier III)
Cummins QSB 3.3L four cylinder / turbo-charged diesel rated at 74kW (99 hp) at 2600 rpm. Includes std. 120V engine block heater and air intake “Grid” heater. Engine hour meter located in dash display. Alternator: 90 amp. Maximum Torque: 415Nm (306 ft/lb)NOTE: Required for sale outside of North America and European Union countries.
Engine (Tier IV)
Cummins QSB 3.3L four cylinder / turbo-charged diesel rated at 75kW (100 hp) at 2600 rpm. Includes std. 120V engine block heater and air intake “Grid” heater. Engine hour meter located in dash display. Alternator: 120 amp.Maximum Torque: 414Nm (305 ft/lb). Fuel requirements: Maximum of 15 ppm sulphur content. Requires “Ultra Low” sulphur diesel fuel.NOTE: Tier IV required for sale in North America and European Union countries.
Transmission
Powershift with four speeds forward and four reverse. Steering column mounted shifter.
6
Specifications
Gross vehicle weight (G.V.W.)
13 488 kg (29,735 lb) basic unit with Tier IV engine.
Miscellaneous standard equipment
18 t (20 USt) two sheave low profile “galvanize coated”hook block with “quick reeve design”. Back-up motion alarm; outrigger motion alarm; non-skid decking;front and rear lifting, towing, and tie-down lugs.
*Denotes optional equipment
Tires
Tubeless type, semi-aggressive tread, 12.00R20.
Brakes
Hydraulic actuated internal wet-disc service brake acting on each drive wheel. Dash mounted rocker switch with indicator light for activating or release of the dry disc parking brake mounted on the transmission output yoke.
Lights
Full LED lighting includes turn indicators, head, tail, brake, and hazard warning lights recessed mounted.
Maximum speed
33.8 km/h (21.0 mph)
Gradeability (theoretical)
68%.....(to drive train stall) NO LOAD40%....(to drive train stall) with 9072 kg(20,000 lb) DECK LOAD
Suspension/axles
Front: Drive / steer in both two wheel driveand four wheel driveRear: non-drive with steer in two wheel drive,drive/steer in four wheel driveFront axle is rigid mounted to frame. Rear axle offers 1.5˚ of oscillation
Steer
Standard three steering modes.Front (two wheel), four wheel coordinated, andfour wheel crab steer with electronic self realignment.Three position rocker switch located on dash panel.
Outside Turning Radius:Two wheel steer: 6,2 m (20 ft 4.8 in)Four wheel steer: 3,9 m (13 ft 1.0 in)
*Optional equipment
AUXILIARY LIGHTING: Includes cab mountedamber flashing light and dual base boom mountedLED work lights.
CONVENIENCE PACKAGE: Includes front and rear pintle hitch, dual rear view mirrors, head and tail light metal mesh grille covers.
ENCLOSED CAB PACKAGE: Includes heater and defroster, cab dome light, all window glass, and two-piece split door.
FOUR WHEEL DRIVE
Below deck hydraulic tow winch with 4536 kg (10,000 lb) capacity.
4,6 m (15 ft) fixed boom extension
Air conditioning (enclosed cab option required)
Hoist third wrap indicator with hoist function cut-out
Hoist drum rotation indicator
360˚ swing lock
C.E. compliant package
*Operators control station enclosed
Includes the standard cab shell and all controls and indicators noted above, with the addition of front, rear, and right side glass, a split (two-piece) hinged door with sliding glass, front windshield wiper and washer, hot water heater and defroster with fan and cab dome light.
Electrical system
One heavy duty maintenance free 12V battery, 820CCA at 0˚F
Drive
Two-wheel (front-wheel) as standard with four-wheel-drive as an option. Drive axles supplied with planetary hubs and limited slip differential.
R 2140 mm (84.3")RADIUS A
RADIUS B
RADIUS C
RADIUS D
RADIUS E
18°18°
173 mm (6.8")
2475
mm
(97.
4")
936 mm(36.9")
223 mm (8.8")
1540
mm
(60.
6")
40°1431 mm
(56.3")
80°
1140 mm(44.9")
1546 mm (60.9")
15,2 m (50') BOOM PIVOTING NOSE*With optional boom only
12,5 m (41')BOOMSHOWN
2481
mm
(97.
7")
1994 mm (78.5")4020 mm (158.3")
1195 mm (47.0")2420 mm (95.3")
15 253 mm (600.5") EXTENDED15,2 m (50') BOOM 5277 mm (207.8") RETRACTED
12 519 mm (492.9") EXTENDED
12,5 m (41') BOOM 5407 mm (212.9") RETRACTED
7001 mm (275.6") RETRACTED 12,5 m (41') BOOM 6871 mm (270.5") RETRACTED 15,2 m (50') BOOM
2472 mm (97.3")
1283 mm (50.5")
1073 mm (42.4")
4658 mm (183.4")
Grove YB5515-2 7
Dimensions
Dimensions are shown in mm (in).
R 2140 mm (84.3")RADIUS A
RADIUS B
RADIUS C
RADIUS D
RADIUS E
18°18°
173 mm (6.8")
2475
mm
(97.
4")
936 mm(36.9")
223 mm (8.8")
1540
mm
(60.
6")
40°1431 mm
(56.3")
80°
1140 mm(44.9")
1546 mm (60.9")
15,2 m (50') BOOM PIVOTING NOSE*With optional boom only
12,5 m (41')BOOMSHOWN
2481
mm
(97.
7")
1994 mm (78.5")4020 mm (158.3")
1195 mm (47.0")2420 mm (95.3")
15 253 mm (600.5") EXTENDED15,2 m (50') BOOM 5277 mm (207.8") RETRACTED
12 519 mm (492.9") EXTENDED
12,5 m (41') BOOM 5407 mm (212.9") RETRACTED
7001 mm (275.6") RETRACTED 12,5 m (41') BOOM 6871 mm (270.5") RETRACTED 15,2 m (50') BOOM
2472 mm (97.3")
1283 mm (50.5")
1073 mm (42.4")
4658 mm (183.4")
Dimensions
A B C DE
12.5 m (41 ft) boomE
15,2 m (50 ft) boom
Two-wheel steer 3375 mm (11 ft 1 in)
6058 mm (19 ft 10.5 in)
6218 mm (20 ft 4.8 in)
6675 mm (21 ft 10.8 in)
7750 mm (25 ft 5 in)
7662 mm (25 ft 2 in)
Four-wheel steer 1722 mm (5 ft 8 in)
3841 mm (12 ft 7 in)
3993 mm (13 ft 1 in)
4481 mm (14 ft 8 in)
5572 mm (18 ft 3 in)
5478 mm (18 ft 0 in)
8
Dimensions and weights
Weights
GVW Front Rear
kg lb kg lb kg lb
Basic machine: Including 12,5 m (41 ft) main boom, main hoist with 97,5 m (320 ft) of wire rope, 18 t (20 USt) hook block, full counterweight, Tier IV engine 13 488 29,735 5817 12,823 7671 16,912
Add: enclosed cab, heater and glass 84,8 187 37,1 82 47,6 105
Crane weight 13 573 29,922 5854 12,905 7719 17,017
Basic machine: Including 12,5 m (41 ft) main boom, main hoist with 97,5 m (320 ft) of wire rope, 18 t (20 USt) hook block, full counterweight, Tier IV engine 13 488 29,735 5817 12,823 7671 16,912
Add: 4,6 m (15 ft) fixed swingaway extension and extension carrier brackets and downhaul weight 178 394 271 598 -93 -204
Crane weight 13 666 30,129 6088 13,421 7578 16,708
Basic machine: Including 12,5 m (41 ft) main boom, main hoist with 97,5 m (320 ft) of wire rope, 18 t (20 USt) hook block, full counterweight, Tier IV engine 13 488 29,735 5817 12,823 7671 16,912
Add: 5,4 m - 15,4 m (17.8 ft - 50 ft) four-section full-power boom 435 961 363 802 72 159
Crane weight 13 923 30,696 6180 13,625 7743 17,071
955 mm(37.6")
1994 mm(78.5")
1910 mm (75.2")
1951 mm (76.8")
975 mm (38.4")
2320 mm (91.3")
1159.804 mm (45.7")
2472 mm (97.3")
2671 mm (105.2")
2439 mm (96.0") 1220 mm (48.0")
1336 mm (52.6")
2020 mm (79.5") 4039 mm (159.0")
2136 mm (84.1")
4271 mm (168.1")
165 mm(6.5")
1338 mm (52.7")
743 mm(29.3")
2737 mm(107.8")
1824 mm(71.8")
Grove YB5515-2 9
Working range imperial
THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE. The individual crane’s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane.
Operating radius in feet from axis of rotation
Hei
ght
fro
m t
he
gro
un
d in
feet
Working range: 5,5 m -12,5 m (18 ft - 41 ft) boom (standard)
0 44 88 12 16 20 24 28 32 36 40 44 48 52 56
68
64
60
56
52
48
44
40
36
32
28
24
20
16
12
8
4
0
0°
5°
10°
15°
20°
30°
35°
40°
45°50°
55˚55°60°
65°69°
17.7
' BO
OM
41.1
' BO
OM
26.0
' BO
OM
34.0
' BO
OM
25°
10
Load chart imperial
THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE. The individual crane’s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane.
1) The rated loads are the maximum lift capacities as determined by operating radius, boom length and boom angle. The operating radius is the horizontal distance from a projection of the axis of rotation to the supporting surface, before loading, to the center of vertical hoist line or tackle with load applied.
2) The rated loads shown on outriggers do not exceed 85% of actual tipping. The rated loads shown on rubber do not exceed 75% of actual tipping. Retracted outrigger loads meet ASME B30.5-2011. These ratings are based on freely suspended loads with the crane leveled, standing on a firm, uniform supporting surface. Practical working loads depend on supporting surface, op-erating radius and other factors affecting stabil-ity. Hazardous surroundings, climatic conditions, experience of personnel and proper training must all be taken into account by the operator.
3) The weights of all load handling devices such as hooks, hook blocks, slings, etc., except the hoist rope, shall be considered part of the load. See above.
4) Ratings on outriggers are for either outriggers fully extended and down or fully retracted and down. Ratings for outriggers fully retracted and down will apply for any intermediate outrigger setting.
5) Ratings on rubber depend on 12.00R20 tire capacity, condition of tires and proper infla-tion pressure (130 psi). Loads on rubber may be transported at a maximum speed of 2.5 mph on a smooth, hard, level surface with boom retracted to the shortest length possible and centered over front. Do not use jib with crane on rubber.
6) For operating radius not shown, use load rat-ing of next larger radius. 7) The maximum deck load only is 20,000 lb. Combined boom and deck loads are not permit-ted on rubber.
8) Do not induce any external side loads to boom or jib.
NOTES:SHADED AREAS ARE GOVERNED BY STRUCTURAL STRENGTH, DO NOT RELY ON TIPPING.
OPERATION OF THIS EQUIPMENT IN EXCESS OF RATING CHARTS AND DISREGARD OF INSTRUCTIONS IS DANGEROUS AND VOIDS WARRANTY.
MAIN BOOM LOAD RATINGS ON OUTRIGGERSExtended and Down 360˚ or Retracted and Down Front/Rear
17.7 ft BOOM 26 ft BOOM 34 ft BOOM 41.1 ft BOOM
Radius(ft)
RatedLoad(lb)
BoomAngle(deg)
RatedLoad(lb)
BoomAngle(deg)
RatedLoad(lb)
BoomAngle(deg)
RatedLoad(lb)
BoomAngle(deg)
MAIN BOOM LOAD RATINGS ON OUTRIGGERSRetracted and Down 360˚
17.7 ft BOOM 26 ft BOOM 34 ft BOOM 41.1 ft BOOM
Radius(ft)
RatedLoad(lb)
BoomAngle(deg)
RatedLoad(lb)
BoomAngle(deg)
RatedLoad(lb)
BoomAngle(deg)
RatedLoad(lb)
BoomAngle(deg)
68
101214
14.716182022
22.924262830
30.9323436
37.9
68
101214
14.716182022
22.924262830
30.9323436
37.9
655748
37.521.5 0
– – – – – – – – – – – – – –
655748
37.521.5 0 – – – – – – – – – – – – – –
–68.563.558.5
5351
46.540
31.519.5 0
– – – – – – – – –
–68.563.558.5
5351
46.540
31.519.5 0 – – – – – – – – –
30,00026,85022,30018,60015,00013,500
––––––––––––––
–26,40021,00017,50014,90013,50012,250
11,000 9200 7400 6900
– – – – – – – – –
– – –6763
61.55955
50.545.543.540.534.5
2716.5 0
– – – –
– – –6763
61.55955
50.545.543.540.534.5
2716.5 0 – – – –
– – – –
68.567.565.5
6359
55.554524844
39.538
34.52921
0
– – – –
68.567.565.5
6359
55.554524844
39.538
34.52921
0
– – –
17,00014,00013,25012,40011,2009550830077507100
6000530045004100
– – – –
– –
– –
13,35013,10012,45011,350968084507750734064505730512048504620418038003480
26,00019,50013,630 9730 7390 6810
––––––––––––––
– 17,94012,89099207720680061655030419035303280
– – – – – – – – –
– – –
9500768068506310520043503690345031602730237020801950
– – – –
– – – –
7440685062005250442037703550324028102450214019101880165014601290
15°30°
SIDE
FRONT REAR
15°30°
SIDE
Grove YB5515-2 11
Load chart imperial
THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE. The individual crane’s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane.
NOTES:JIB CAPACITY IS LIMITED BY BOTH STRUCTURAL CAPACITY CHART AND MAIN CAPACITY CHART.
SHADED AREAS ARE GOVERNED BY STRUCTURAL STRENGTH, DO NOT RELY ON TIPPING.
OPERATION OF THIS EQUIPMENT IN EXCESS OF RATING CHARTS AND DISREGARD OF INSTRUCTIONS IS DANGEROUS AND VOIDS WARRANTY.
1) The rated loads are the maximum lift capacities as determined by operating radius, boom length and boom angle. The operating radius is the horizontal distance from a projection of the axis of rotation to the supporting surface, before loading, to the center of vertical hoist line or tackle with load applied.
2) The rated loads shown on outriggers do not ex-ceed 85% of actual tipping. The rated loads shown on rubber do not exceed 75% of actual tipping. Retracted outrigger loads meet ASME B30.5-2011. These ratings are based on freely suspended loads with the crane leveled, standing on a firm, uniform supporting surface. Practical working loads depend on supporting surface, operating radius and other factors affecting stability. Hazardous surroundings, climatic conditions, experience of personnel and proper training must all be taken into account by the operator.
3) The weights of all load handling devices such as hooks, hook blocks, slings, etc., except the hoist rope, shall be considered part of the load. See above.
4) Ratings on outriggers are for either outriggers fully extended and down or fully retracted and down. Rat-ings for outriggers fully retracted and down will apply for any intermediate outrigger setting.
5) Ratings on rubber depend on 12.00R20 tire capacity, condition of tires and proper inflation pressure (130 psi). Loads on rubber may be transported at a maxi-mum speed of 2.5 mph on a smooth, hard, level surface with boom retracted to the shortest length possible and centered over front. Do not use jib with crane on rubber.
6) For operating radius not shown, use load rating of next larger radius. 7) The maximum deck load only is 20,000 lb. Combined boom and deck loads are not permitted on rubber.
8) Do not induce any external side loads to boom or jib.
6
Radius (ft)
MAIN BOOM ON RUBBERAny Boom Length
Front Rating (lb) 360̊ Rating (lb)
17,80014,60011 ,8009 55080107 5006 93056104 7 3039603650330028602530231021002035187 516501450
68101214
14.716182022
22.924262830
30.9323436
37.9
15,65011 ,4009 7 20859067 1 057 505390440036303080285025852255198017 6016501540137512601100
15°30°
SIDE
FRONT REAR
15°30°
SIDE
12
Working range imperial
THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE. The individual crane’s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane.
Operating radius in feet from axis of rotation
Hei
ght
fro
m t
he
gro
un
d in
feet
65°60°
55°50°
45°
40°
35°
30°
25°
20°
15°
10°
5°
0°
17.3
' BO
OM
29' B
OO
M40
' BO
OM
50' B
OO
M65
' BO
OM
W
ITH
15' J
IB
69°
Working range: 5,4 m - 15,4 m (17.8 ft - 50 ft) (optional)
Grove YB5515-2 13
Load chart imperial
THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE. The individual crane’s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane.
NOTES:SHADED AREAS ARE GOVERNED BY STRUCTURAL STRENGTH, DO NOT RELY ON TIPPING.
OPERATION OF THIS EQUIPMENT IN EXCESS OF RATING CHARTS AND DISREGARD OF INSTRUCTIONS IS DANGEROUS AND VOIDS WARRANTY.
MAIN BOOM LOAD RATINGS ON OUTRIGGERSExtended and Down 360 ̊or Retracted and Down Front/Rear
1 7 .3 ft BOOM 29 ft BOOM 40 ft BOOM 50 ft BOOM
Radius(ft)
RatedLoad(lb)
BoomAngle(deg)
RatedLoad(lb)
BoomAngle(deg)
RatedLoad(lb)
BoomAngle(deg)
RatedLoad(lb)
BoomAngle(deg)
MAIN BOOM LOAD RATINGS ON OUTRIGGERSRetracted and Down 360˚
1 7 .3 ft BOOM 29 ft BOOM 40 ft BOOM 50 ft BOOM
Radius(ft)
RatedLoad
(lb)
BoomAngle(deg)
RatedLoad(lb)
BoomAngle(deg)
RatedLoad(lb)
BoomAngle(deg)
RatedLoad
(lb)
BoomAngle(deg)
681012
14.21618202224
25.92830323436
36.938404244
46.9
681012
14.21618202224
25.92830323436
36.938404244
46.9
64.556.54736
0 – – – – – – – – – – – – – – – – –
64.556.54736
0 – – – – – – – – – – – – – – – –
– –67
62.557 .553
47 .5413425
0 – – – – – – – – – – –
– –67
62.557 .553
47 .5413425
0 – – – – – – – – – – –
30,00025,7 6021 ,27 018,05013,1 001 8900
––––––––––––––––
––
16,95016,95015,52012,42010,990
9830 8600 7 400 6480
–––––––––––
– – – –67 .565
61 .558
54.55147
42.538
32.525.5
16 0 – – – – –
– – – –67 .565
61 .558
54.55147
42.538
32.525.5
16 0 – – – – –
– – – – – –68.56663
60.558555249
45.542
40.538342923
0
– – – – – –68.5666360.55855524945.54240.538342923
0
– – – –
15,52012,42010,9909 800867 07 4906 5805 7 7 05 1 304 51 04 1 203 7 1 03 620
– –
– – –
– –
– – – –
10,9909830870075006620580051 60462041 6037 10359034103040276024102110
30,00025,7 6018,60013,40010,000
–––––––––––––––––
– –
16,95013,30010,40085507 05059205040433037 80
– – – – – – – – – – –
– – – –
9 97 08 5007 1 506 0305 1 604 4503 9003 39029802630233020601 960
– – – – –
– – – – – –
6950591 0506043903860337 0297 0263023402080197 018501650147 0131 01100
15°30°
SIDE
FRONT REAR
15°30°
SIDE
1) The rated loads are the maximum lift capacities as determined by operating radius, boom length and boom angle. The operating radius is the horizontal distance from a projection of the axis of rotation to the supporting surface, before loading, to the center of vertical hoist line or tackle with load applied.
2) The rated loads shown on outriggers do not exceed 85% of actual tipping. The rated loads shown on rubber do not exceed 75% of actual tipping. Retracted outrigger loads meet ASME B30.5-2011. These ratings are based on freely suspended loads with the crane leveled, standing on a firm, uniform supporting surface. Practical working loads depend on supporting surface, op-erating radius and other factors affecting stabil-ity. Hazardous surroundings, climatic conditions, experience of personnel and proper training must all be taken into account by the operator.
3) The weights of all load handling devices such as hooks, hook blocks, slings, etc., except the hoist rope, shall be considered part of the load. See above.
4) Ratings on outriggers are for either outriggers fully extended and down or fully retracted and down. Ratings for outriggers fully retracted and down will apply for any intermediate outrigger setting.
5) Ratings on rubber depend on 12.00R20 tire capacity, condition of tires and proper infla-tion pressure (130 psi). Loads on rubber may be transported at a maximum speed of 2.5 mph on a smooth, hard, level surface with boom retracted to the shortest length possible and centered over front. Do not use jib with crane on rubber.
6) For operating radius not shown, use load rat-ing of next larger radius. 7) The maximum deck load only is 20,000 lb. Combined boom and deck loads are not permit-ted on rubber.
8) Do not induce any external side loads to boom or jib.
14
Load chart imperial
THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE. The individual crane’s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane.
15°30°
SIDE
FRONT REAR
15°30°
SIDE
Radius (ft)
MAIN BOOM ON RUBBERAny Boom Length
Front Rating (lb) 360˚ Rating (lb)
15 FT FIXED JIB CAPACITIES ON EXTENDED OUTRIGGERSMain BoomAngle (deg)
Jib O�set Angle0 deg 15 deg 30 deg
To 40 ftMain Boom
To 50 ftMain Boom
To 40 ftMain Boom
To 50 ftMain Boom
To 40 ftMain Boom
68
1012
14.21618202224
25.92830323436
36.938404244
46.9
17,80014,35011,4509790817070206210554048304160363032802910260023202080198019001700152013701160
6965605550454035302520151050
750071806000518045804040349030802770254023702240216021202110
702056704770413034402860244021201890171015701480141013801370
548048904440410038303620327029302660247023202220
–––
528045103940352031702680232020401830167015501460
–––
395036903510340032203130307028602630
––––––
To 50 ftMain Boom
395036903510321029702580225020001810
––––––
15,55011,500
8950742060305350445036703050264022201960165014001170990900820670510420–
NOTES:JIB CAPACITY IS LIMITED BY BOTH STRUCTURAL CAPACITY CHART AND MAIN CAPACITY CHART.
SHADED AREAS ARE GOVERNED BY STRUCTURAL STRENGTH, DO NOT RELY ON TIPPING.
OPERATION OF THIS EQUIPMENT IN EXCESS OF RATING CHARTS AND DISREGARD OF INSTRUCTIONS IS DANGEROUS AND VOIDS WARRANTY.
1) The rated loads are the maximum lift capacities as determined by operating radius, boom length and boom angle. The operating radius is the horizontal distance from a projection of the axis of rotation to the supporting surface, before loading, to the center of vertical hoist line or tackle with load applied.
2) The rated loads shown on outriggers do not ex-ceed 85% of actual tipping. The rated loads shown on rubber do not exceed 75% of actual tipping. Retracted outrigger loads meet ASME B30.5-2011. These ratings are based on freely suspended loads with the crane leveled, standing on a firm, uniform supporting surface. Practical working loads depend on supporting surface, operating radius and other factors affecting stability. Hazardous surroundings, climatic conditions, experience of personnel and proper training must all be taken into account by the operator.
3) The weights of all load handling devices such as hooks, hook blocks, slings, etc., except the hoist rope, shall be considered part of the load. See above.
4) Ratings on outriggers are for either outriggers fully extended and down or fully retracted and down. Rat-ings for outriggers fully retracted and down will apply for any intermediate outrigger setting.
5) Ratings on rubber depend on 12.00R20 tire capacity, condition of tires and proper inflation pressure (130 psi). Loads on rubber may be transported at a maxi-mum speed of 2.5 mph on a smooth, hard, level surface with boom retracted to the shortest length possible and centered over front. Do not use jib with crane on rubber.
6) For operating radius not shown, use load rating of next larger radius. 7) The maximum deck load only is 20,000 lb. Combined boom and deck loads are not permitted on rubber.
8) Do not induce any external side loads to boom or jib.
Grove YB5515-2 15
Working range metric
THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE. The individual crane’s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane.
Working range: 5,5 m -12,5 m boom (standard)
01,22-1,22
2,44-2,443,66
4,886,1 0
7,328,53
9,7 510,97
12,1 913,41
14,6315,85
17, 07
20,7 3
19,51
18,29
17,07
15,85
14,63
13,41
12,19
10,97
9,7 5
8,53
7 ,32
6,1 0
4,88
3,66
2,44
1,22
0
0°
5°
1 0°
1 5°
20°
30°
35°
40°
45°50°
5555°60°
65°69°
5,4
M B
OO
M
1 2,5
M B
OO
M
7,9
M B
OO
M10
,4 M
BO
OM
25°
Operating radius in meters from axis of rotation
Hei
ght
fro
m t
he
gro
un
d in
met
ers
16
Load chart metric
THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE. The individual crane’s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane.
1) The rated loads are the maximum lift capacities as determined by operating radius, boom length and boom angle. The operating radius is the horizontal distance from a projection of the axis of rotation to the supporting surface, before loading, to the center of vertical hoist line or tackle with load applied.
2) The rated loads shown on outriggers do not exceed 85% of actual tipping. The rated loads shown on rubber do not exceed 75% of actual tipping. Retracted outrigger loads meet ASME B30.5-2011. These ratings are based on freely suspended loads with the crane leveled, standing on a firm, uniform supporting surface. Practical working loads depend on supporting surface, op-erating radius and other factors affecting stabil-ity. Hazardous surroundings, climatic conditions, experience of personnel and proper training must all be taken into account by the operator.
3) The weights of all load handling devices such as hooks, hook blocks, slings, etc., except the hoist rope, shall be considered part of the load. See above.
4) Ratings on outriggers are for either outriggers fully extended and down or fully retracted and down. Ratings for outriggers fully retracted and down will apply for any intermediate outrigger setting.
5) Ratings on rubber depend on 12.00R20 tire capacity, condition of tires and proper inflation pressure (8,9 bar). Loads on rubber may be trans-ported at a maximum speed of 4,0 km/h on a smooth, hard, level surface with boom retracted to the shortest length possible and centered over front. Do not use jib with crane on rubber.
6) For operating radius not shown, use load rat-ing of next larger radius. 7) The maximum deck load only is 7260 kg. Com-bined boom and deck loads are not permitted on rubber.
8) Do not induce any external side loads to boom or jib.
NOTES:SHADED AREAS ARE GOVERNED BY STRUCTURAL STRENGTH, DO NOT RELY ON TIPPING.
OPERATION OF THIS EQUIPMENT IN EXCESS OF RATING CHARTS AND DISREGARD OF INSTRUCTIONS IS DANGEROUS AND VOIDS WARRANTY.
15°30°
SIDE
FRONT REAR
15°30°
SIDE
MAIN BOOM LOAD RATINGS ON OUTRIGGERSExtended and Down 360 ̊or Retracted and Down Front/Rear
5.4 m BOOM 7 .9 m BOOM 1 0.4 m BOOM 1 2.5 m BOOM
Radius(m)
RatedLoad(kg)
BoomAngle(deg)
RatedLoad(kg)
BoomAngle(deg)
RatedLoad(kg)
BoomAngle(deg)
RatedLoad(kg)
BoomAngle(deg)
MAIN BOOM LOAD RATINGS ON OUTRIGGERSRetracted and Down 360˚
5,4 m BOOM 7,9 m BOOM 10,4 m BOOM 1 2,5 m BOOM
Radius(m)
RatedLoad(kg)
BoomAngle(deg)
RatedLoad(kg)
BoomAngle(deg)
RatedLoad(kg)
BoomAngle(deg)
RatedLoad(kg)
BoomAngle(deg)
1,82,43,03,74,34,54,95,56,16,77 ,07 ,37 ,98,59,19,49,810,411 ,011 ,6
6557 ,549
36,520,5 0 – – – – – – – – – – – – – –
–696458
52,551
46,539,531 ,519,5 0 – – – – – – – – –
13 60012 1 7 59 8508 0506 8006 1 25
–
– – – – – – – – – – – – –
– 11 97 5
95257 9256 7 506 1 255 550497 54150335031 25
– – – – – – – – –
– – –66,563
61 ,559
54,550,545,543,540,534,527 ,51 7 ,5 0 – – – –
– – – –68,567 ,565,56259
55,55452484440
37 ,53428
20,5 0
– – –
7 7 006 3506 0005600507 5432537 503500320027 00240020251850
– –
– –
– –
– –
6 0505 9255 6255 1 254 37 53 825351 53 32529252600232022002090189017 20157 0
1 ,82,43,03,74,34,54,95,56,16,77 ,07 ,37 ,98,59,19,49,81 0,41 1 ,01 1 ,6
6557 ,549
36,520,5 0
– – – – – – – – – – – – – –
–696458
52,551
46,539,531 ,519,5 0 – – – – – – – – –
– 8 130548045003500308027 902280190016001480
– – – – – – – – –
– – –66,563
61,559
54,550,545,543,540,534,527 ,51 7 ,5 0 – – – –
– – – –68,567 ,565,56259
55,55452484440
37 ,53428
20,5 0
– – –
4300348031 0028602350197016701560143012301070940885
– –
– –
– – – –
337 031002810238020001710161 014701270111097 08608507 40660580
11 7 7 588406 1 804 41 033503080
– – – – – – – – – – – – – –
Grove YB5515-2 17
Load chart metric
THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE. The individual crane’s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane.
NOTES:JIB CAPACITY IS LIMITED BY BOTH STRUCTURAL CAPACITY CHART AND MAIN CAPACITY CHART.
SHADED AREAS ARE GOVERNED BY STRUCTURAL STRENGTH, DO NOT RELY ON TIPPING.
OPERATION OF THIS EQUIPMENT IN EXCESS OF RATING CHARTS AND DISREGARD OF INSTRUCTIONS IS DANGEROUS AND VOIDS WARRANTY.
1) The rated loads are the maximum lift capacities as determined by operating radius, boom length and boom angle. The operating radius is the horizontal distance from a projection of the axis of rotation to the supporting surface, before loading, to the center of vertical hoist line or tackle with load applied.
2) The rated loads shown on outriggers do not ex-ceed 85% of actual tipping. The rated loads shown on rubber do not exceed 75% of actual tipping. Retracted outrigger loads meet ASME B30.5-2011. These ratings are based on freely suspended loads with the crane leveled, standing on a firm, uniform supporting surface. Practical working loads depend on supporting surface, operating radius and other factors affecting stability. Hazardous surroundings, climatic conditions, experience of personnel and proper training must all be taken into account by the operator.
3) The weights of all load handling devices such as hooks, hook blocks, slings, etc., except the hoist rope, shall be considered part of the load. See above.
4) Ratings on outriggers are for either outriggers fully extended and down or fully retracted and down. Ratings for outriggers fully retracted and down will apply for any intermediate outrigger setting.
5) Ratings on rubber depend on 12.00R20 tire capac-ity, condition of tires and proper inflation pressure (8,9 bar). Loads on rubber may be transported at a maximum speed of 4,0 km/h on a smooth, hard, level surface with boom retracted to the shortest length possible and centered over front. Do not use jib with crane on rubber.
6) For operating radius not shown, use load rating of next larger radius. 7) The maximum deck load only is 7260 kg. Combined boom and deck loads are not permitted on rubber.
8) Do not induce any external side loads to boom or jib.
15°30°
SIDE
FRONT REAR
15°30°
SIDE
Radius (m)
MAIN BOOM ON RUBBERAny Boom Length
Front Rating (kg) 360̊ Rating (kg)8 07 06 6205 3504 3303 6303 4003 1 402 54021 4017 9016501490129011 4010409509208507 50650
1,82,43,03,74,34,54,95,56,16,77,07,37,98,59,19,49,81 0,41 1,01 1,6
7 1005 1 7 04 4003890304026002440199016401390129011 7010208907 907 4069062057 0490
18
Working range metric
THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE. The individual crane’s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane.
Working range: 5,4 m - 15,4 m (optional)
65°60°
55°50°
45°
40°
35°
30°
25°
20°
15°
10°
5°
0°
5,3
m B
OO
M
8,8
m B
OO
M1 2
,2 m
BO
OM
15,2
m B
OO
M
19,8
m B
OO
M
WIT
H 4
,6 m
JIB
69˚
23,823,222,621 ,921 ,320,720,119,518,918,317 ,717 ,116,515,815,214,614,013,412,812,211,611,010,49,89,18,57,97,36,76,15,54,94,33,73,02,41,81,20,6
0
23,823,222,621 ,921 ,320,720,119,518,918,317 ,717 ,116,515,815,214,614,013,412,812,211 ,611 ,010,49,89,18,57 ,97 ,36,76,15,54,94,33,73,02,41,81,20,60
2,4 1,2 0 1,2 2,4 3,7 4,9 6,1 7 ,3 8,5 9,8 11,0 12,2 13,4 14,6 15,2 16,5 17,7 18,9
2,4 1,2 0 1,2 2,4 3,7 4,9 6,1 7 ,3 8,5 9,8 11,0 12,2 13,4 14,6 15,2 16,5 17 ,7 18,9
1,8 0,6 0,6 1,8 3,0 4,3 5,5 6,7 7 ,9 9,1 10,4 11,6 12,8 14,0 15,2 15,8 17,1 18,3 19,5
1,8 0,6 0,6 1,8 3,0 4,3 5,5 6,7 7 ,9 9,1 10,4 11,6 12,8 14,0 15,2 15,8 17 ,1 18,3 19,5
Operating radius in meters from axis of rotation
Hei
ght
fro
m t
he
gro
un
d in
met
ers
Grove YB5515-2 19
Load chart metric
THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE. The individual crane’s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane.
NOTES:SHADED AREAS ARE GOVERNED BY STRUCTURAL STRENGTH, DO NOT RELY ON TIPPING.
OPERATION OF THIS EQUIPMENT IN EXCESS OF RATING CHARTS AND DISREGARD OF INSTRUCTIONS IS DANGEROUS AND VOIDS WARRANTY.
15°30°
SIDE
FRONT REAR
15°30°
SIDE
1) The rated loads are the maximum lift capacities as determined by operating radius, boom length and boom angle. The operating radius is the horizontal distance from a projection of the axis of rotation to the supporting surface, before loading, to the center of vertical hoist line or tackle with load applied.
2) The rated loads shown on outriggers do not exceed 85% of actual tipping. The rated loads shown on rubber do not exceed 75% of actual tipping. Retracted outrigger loads meet ASME B30.5-2011. These ratings are based on freely suspended loads with the crane leveled, standing on a firm, uniform supporting surface. Practical working loads depend on supporting surface, op-erating radius and other factors affecting stabil-ity. Hazardous surroundings, climatic conditions, experience of personnel and proper training must all be taken into account by the operator.
3) The weights of all load handling devices such as hooks, hook blocks, slings, etc., except the hoist rope, shall be considered part of the load. See above.
4) Ratings on outriggers are for either outriggers fully extended and down or fully retracted and down. Ratings for outriggers fully retracted and down will apply for any intermediate outrigger setting.
5) Ratings on rubber depend on 12.00R20 tire capacity, condition of tires and proper inflation pressure (8,9 bar). Loads on rubber may be trans-ported at a maximum speed of 4,0 km/h on a smooth, hard, level surface with boom retracted to the shortest length possible and centered over front. Do not use jib with crane on rubber.
6) For operating radius not shown, use load rat-ing of next larger radius. 7) The maximum deck load only is 7260 kg. Com-bined boom and deck loads are not permitted on rubber.
8) Do not induce any external side loads to boom or jib.
MAIN BOOM LOAD RATINGS ON OUTRIGGERSExtended and Down 360° or Retracted and Down Front/Rear
5,3 m BOOM 8,8 m BOOM 12,2 m BOOM 15,2 m BOOM
Radius(m)
RatedLoad(kg)
BoomAngle(deg)
RatedLoad(kg)
BoomAngle(deg)
RatedLoad(kg)
BoomAngle(deg)
RatedLoad(kg)
BoomAngle(deg)
MAIN BOOM LOAD RATINGS ON OUTRIGGERSRetracted and Down 360°
5,3 m BOOM 8,8 m BOOM 12,2 m BOOM 15,2 m BOOM
Radius(m)
RatedLoad(kg)
BoomAngle(deg)
RatedLoad(kg)
BoomAngle(deg)
RatedLoad(kg)
BoomAngle(deg)
RatedLoad(kg)
BoomAngle(deg)
1,82,43,03,74,34,95,56,16,77,37,98,59,19,8
10,411,011,211,612,212,813,414,3
1,82,43,03,74,34,95,56,16,77,37,98,59,19,8
10,411,011,211,612,212,813,414,3
65574835 0 – – – – – – – – – – – – – – – – –
65574835
0 – – – – – – – – – – – – – – – – –
– –
67,562,557,552,5
47413425 0 – – – – – – – – – – –
– –67,562,557,552,5
47413425
0 – – – – – – – – – – –
13 60011 680964081805940
1890 – – – – – – – – – – – – – – – – –
––
768576857025563049804450390033502930
–––––––––––
– – – –68
64,561,558
54,5514743383225
15,5 0 – – – – –
– – – –68
64,561,558
54,5514743383225
15,5 0 – – – – –
– – – – – –68,5
6663
60,5585552
48,545,5
4240,5
383429
23,5 0
– – – – – –68,5
6663
60,5585552
48,545,5
4240,5
383429
23,5 0
– – – –
7030563049804445393033902980261023202045186516801640
– –
– – –
– –
– – – –
498044553940340030002630234020951885168016251545137512501090995
13 60011 685843059554585
– – – – – – – – – – – – – – – – –
– – – –
45653830323027352345202517701550136511851050930895
– – – – –
– – – – – –
314026752300199517501540136011851055940905835745665595500
– –
768559554770385031852680229019701715
– – – – – – – – – – –
20
Load chart metric
THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE. The individual crane’s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane.
15°30°
SIDE
FRONT REAR
15°30°
SIDE
NOTES:JIB CAPACITY IS LIMITED BY BOTH STRUCTURAL CAPACITY CHART AND MAIN CAPACITY CHART.
SHADED AREAS ARE GOVERNED BY STRUCTURAL STRENGTH, DO NOT RELY ON TIPPING.
OPERATION OF THIS EQUIPMENT IN EXCESS OF RATING CHARTS AND DISREGARD OF INSTRUCTIONS IS DANGEROUS AND VOIDS WARRANTY.
1) The rated loads are the maximum lift capacities as determined by operating radius, boom length and boom angle. The operating radius is the horizontal distance from a projection of the axis of rotation to the supporting surface, before loading, to the center of vertical hoist line or tackle with load applied.
2) The rated loads shown on outriggers do not exceed 85% of actual tipping. The rated loads shown on rubber do not exceed 75% of actual tipping. Retracted outrigger loads meet ASME B30.5-2011. These ratings are based on freely suspended loads with the crane leveled, standing on a firm, uniform supporting surface. Practical working loads depend on supporting surface, operating radius and other factors affecting stability. Hazardous surroundings, climatic conditions, experience of personnel and proper training must all be taken into account by the operator.
3) The weights of all load handling devices such as hooks, hook blocks, slings, etc., except the hoist rope, shall be considered part of the load. See above.
4) Ratings on outriggers are for either outriggers fully extended and down or fully retracted and down. Ratings for outriggers fully re-tracted and down will apply for any intermediate outrigger setting.
5) Ratings on rubber depend on 12.00R20 tire capacity, condition of tires and proper inflation pressure (8,9 bar). Loads on rubber may be transported at a maximum speed of 4,0 km/h on a smooth, hard, level surface with boom retracted to the shortest length pos-sible and centered over front. Do not use jib with crane on rubber.
6) For operating radius not shown, use load rating of next larger radius. 7) The maximum deck load only is 7260 kg. Combined boom and deck loads are not permitted on rubber.
8) Do not induce any external side loads to boom or jib.
Radius (m)
MAIN BOOM ON RUBBERAny Boom Length
Front Rating (kg) 360° Rating (kg)
4,6 m FIXED JIB CAPACITIES ON EXTENDED OUTRIGGERSMain BoomAngle (deg)
Jib Offset Angle0° 15° 30°
To 1 2,2 mMain Boom
To 1 5,2 mMain Boom
To 1 2,2 mMain Boom
To 1 5,2 mMain Boom
To 1 2,2 mMain Boom
80906525521 0444037 0531 852820251 021901 8901 6451 4951 3301 16510459409058557 7 0690620525
69656055504540353025201 51 050
3400325527 202350207 5183015801395125011 50107 51015980960955
31 80257 021 60187 01560129511059608507 7 57 1 067 0640625620
2485221 5201 0186017 351640148013251205112010501005
–––
2395204517 8515951435121010509258307 507 00660
– – –
17 90167 015901540146014201390129511 95
––––––
To 1 5,2 mMain Boom
17 90167 015901455134511 7 01020900820
– – – – – –
1 ,82,43,03,74,34,95,56,16,77 ,37 ,98,59,19,8
1 0,41 1 ,01 1 ,21 1 ,61 2,21 2,81 3,41 4,3
7 07 052304060336527 602425201516651380119510058857 4563553044540537 03002301 90–
Grove YB5515-2 21
Working range DIN/ISO
THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE. The individual crane’s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane.
Working range: 5,5 m -12,5 m boom (standard)
Operating radius in meters from axis of rotation
Hei
ght
fro
m t
he
gro
un
d in
met
ers
01,22-1,22
2,44-2,443,66
4,886,10
7,328,53
9,7 510,97
12,1913,41
14,6315,85
17,07
20,7 3
19,51
18,29
17 ,07
15,85
14,63
13,41
12,19
10,97
9,7 5
8,53
7,32
6,10
4,88
3,66
2,44
1,22
0
0°
5°
10 °
15°
20°
30°
35°
40°
45°50°
5555°60°
65°69°
5,4
M B
OO
M
1 2,5
M B
OO
M
7,9
M B
OO
M1 0
,4 M
BO
OM
25°
22
Load chart DIN/ISO
1) The rated loads are the maximum lift capacities as determined by operating radius, boom length and boom angle. The operating radius is the horizontal distance from a projection of the axis of rotation to the supporting surface, before loading, to the center of vertical hoist line or tackle with load applied.
2) The rated loads shown on outriggers do not exceed 80% of actual tipping. The rated loads shown on rubber do not exceed 75% of actual tip-ping. These ratings are based on freely suspended loads with the crane leveled, standing on a firm, uniform supporting surface. Practical working loads depend on supporting surface, operat-ing radius and other factors affecting stability. Hazardous surroundings, climatic conditions, experience of personnel and proper training must all be taken into account by the operator.
3) The weights of all load handling devices such as hooks, hook blocks, slings, etc., except the hoist rope, shall be considered part of the load. See above.
4) Ratings on outriggers are for either outriggers fully extended and down or fully retracted and down. Ratings for outriggers fully retracted and down will apply for any intermediate outrigger setting.
5) Ratings on rubber depend on 12.00R20 tire capacity, condition of tires and proper inflation pressure (8,9 bar). Loads on rubber may be trans-ported at a maximum speed of 4,0 km/h on a smooth, hard, level surface with boom retracted to the shortest length possible and centered over front. Do not use jib with crane on rubber.
6) For operating radius not shown, use load rat-ing of next larger radius. 7) The maximum deck load only is 7260 kg. Com-bined boom and deck loads are not permitted on rubber.
8) Do not induce any external side loads to boom or jib.
15°30°
SIDE
FRONT REAR
15°30°
SIDE
MAIN BOOM LOAD RATINGS ON OUTRIGGERSExtended and Down 360 ̊or Retracted and Down Front/Rear
5,4 m BOOM 7 ,7 m BOOM 1 0,4 m BOOM 1 2,5 m BOOM
Radius(m)
RatedLoad(kg)
BoomAngle(deg)
RatedLoad(kg)
BoomAngle(deg)
RatedLoad(kg)
BoomAngle(deg)
RatedLoad(kg)
BoomAngle(deg)
MAIN BOOM LOAD RATINGS ON OUTRIGGERSRetracted and Down 360˚
5,4 m BOOM 7 ,9 m BOOM 1 0,4 m BOOM 1 2,5 m BOOM
Radius(m)
RatedLoad(kg)
BoomAngle(deg)
RatedLoad(kg)
BoomAngle(deg)
RatedLoad(kg)
BoomAngle(deg)
RatedLoad(kg)
BoomAngle(deg)
1,82,43,03,74,34,54,95,56,16,77 ,07 ,37 ,98,59,19,49,8
10,411,011,6
6557 ,549
36,520,5 0 – – – – – – – – – – – – – –
–696458
52,551
46,539,531 ,51 9,5 0 – – – – – – – – –
13 60013 52311 85010 50089807390
– – – – – – – – – – – – – –
– 12 1 0010 8509 6808 7 508 4607 7 456300527 04495421 0
– – – – – – – – –
– – –66,563
61 ,559
54,550,545,543,540,534,527 ,51 7 ,5 0 – – – –
– – – –68,567 ,565,56259
55,55452484440
37 ,53428
20,5 0
– – –
9 1158 2107 93573206235533045654280397 0350031 1 527 902645
– –
– –
– –
– –
7890762069855980521 04590430539953525314528252680251 5228520851925
1,82,43,03,74,34,54,95,56,16,77 ,07 ,37 ,98,59,19,49,8
10,411,011,6
6557 ,549
36,520,5 0 – – – – – – – – – – – – – –
–696458
52,551
46,539,531 ,519,5 0 – – – – – – – – –
– 99557 39556254620437 5384531 852685229521 45
– – – – – – – – –
– – –66,563
61 ,559
54,550,545,543,540,534,527 ,51 7 ,5 0 – – – –
– – – –68,567 ,565,56259
55,55452484440
37 ,53428
20,5 0
– – –
5 3054 4054 1 853 7 353 21 527 352360221 520601 8151 6051 4301 350
– –
– –
– –
– –
4 21 54 01 53 6003 1 2027 352420229021 301 87 51 6651 4901 4051 31 01 1 801 06597 5
13 60011 12580505860451 5421 0
– – – – – – – – – – – – – –
THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE. The individual crane’s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane.
Grove YB5515-2 23
Load chart DIN/ISO
NOTES:JIB CAPACITY IS LIMITED BY BOTH STRUCTURAL CAPACITY CHART AND MAIN CAPACITY CHART.
SHADED AREAS ARE GOVERNED BY STRUCTURAL STRENGTH, DO NOT RELY ON TIPPING.
OPERATION OF THIS EQUIPMENT IN EXCESS OF RATING CHARTS AND DISREGARD OF INSTRUCTIONS IS DANGEROUS AND VOIDS WARRANTY.
1) The rated loads are the maximum lift capacities as determined by operating radius, boom length and boom angle. The operating radius is the horizontal distance from a projection of the axis of rotation to the supporting surface, before loading, to the center of vertical hoist line or tackle with load applied.
2) The rated loads shown on outriggers do not ex-ceed 80% of actual tipping. The rated loads shown on rubber do not exceed 75% of actual tipping. These ratings are based on freely suspended loads with the crane leveled, standing on a firm, uniform supporting surface. Practical working loads depend on supporting surface, operating radius and other factors affecting stability. Hazardous surroundings, climatic conditions, experience of personnel and proper training must all be taken into account by the operator.
3) The weights of all load handling devices such as hooks, hook blocks, slings, etc., except the hoist rope, shall be considered part of the load. See above.
4) Ratings on outriggers are for either outriggers fully extended and down or fully retracted and down. Ratings for outriggers fully retracted and down will apply for any intermediate outrigger setting.
5) Ratings on rubber depend on 12.00R20 tire capac-ity, condition of tires and proper inflation pressure (8,9 bar). Loads on rubber may be transported at a maximum speed of 4,0 km/h on a smooth, hard, level surface with boom retracted to the shortest length possible and centered over front. Do not use jib with crane on rubber.
6) For operating radius not shown, use load rating of next larger radius. 7) The maximum deck load only is 7260 kg. Combined boom and deck loads are not permitted on rubber.
8) Do not induce any external side loads to boom or jib.
Radius (m)
MAIN BOOM ON RUBBERAny Boom Length
Front Rating (kg) 360° Rating (kg)807 06620535043303630342531 6526302225190517 8517 05150013301185112010609508557 7 5
1 ,82,43,03,74,34,54,95,56,16,77 ,07 ,37 ,98,59,19,49,8
1 0,41 1 ,01 1 ,6
7 1 1 55 1 904 41 03 7 65297 027 80257 021 4518201565146514001225107 59508908257 35650585
THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE. The individual crane’s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane.
24
Working range DIN/ISO
Operating radius in meters from axis of rotation
Hei
ght
fro
m t
he
gro
un
d in
met
ers
Working range: 5,4 m - 15,4 m (optional)
65°60°
55°50°
45°
40°
35°
30°
25°
20°
15°
10°
5°
0°
5,3
m F
T B
OO
M8,
8 m
BO
OM
12,2
m B
OO
M15
,2 m
BO
OM
19,8
m B
OO
M
WIT
H 4
,6 m
JIB
69°
23,823,222,621,921,320,720,119,518,918,317,717,116,515,815,214,614,013,412,812,211,611,010,49,89,18,57,97,36,76,15,54,94,33,73,02,41,81,20,60
23,823,222,621,921,320,720,119,518,918,317,717,116,515,815,214,614,013,412,812,211,611,010,49,89,18,57,97,36,76,15,54,94,33,73,02,41,81,20,60
2,4 1,2 1,2 2,4 3,7 4,9 6,1 7,3 8,5 9,8 11,0 12,2 13,4 14,6 15,2 16,5 17,7 18,9
2,4 1,2 1,2 2,4 3,7 4,9 6,1 7,3 8,5 9,8 11,0 12,2 13,4 14,6 15,2 16,5 17,7 18,9
1,8 0,6 0,6 1,8 3,0 4,3 5,5 6,7 7,9 9,1 10,4 11,6 12,8 14,0 15,2 15,8 17,1 18,3 19,5
1,8 0,6 0,6 1,8 3,0 4,3 5,5 6,7 7,9 9,1 10,4 11,6 12,8 14,0 15,2 15,8 17,1 18,3 19,5
THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE. The individual crane’s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane.
Grove YB5515-2 25
Load chart DIN/ISO
NOTES:SHADED AREAS ARE GOVERNED BY STRUCTURAL STRENGTH, DO NOT RELY ON TIPPING.
OPERATION OF THIS EQUIPMENT IN EXCESS OF RATING CHARTS AND DISREGARD OF INSTRUCTIONS IS DANGEROUS AND VOIDS WARRANTY.
15°30°
SIDE
FRONT REAR
15°30°
SIDE
1) The rated loads are the maximum lift capacities as determined by operating radius, boom length and boom angle. The operating radius is the horizontal distance from a projection of the axis of rotation to the supporting surface, before loading, to the center of vertical hoist line or tackle with load applied.
2) The rated loads shown on outriggers do not exceed 80% of actual tipping. The rated loads shown on rubber do not exceed 75% of actual tip-ping. These ratings are based on freely suspended loads with the crane leveled, standing on a firm, uniform supporting surface. Practical working loads depend on supporting surface, operat-ing radius and other factors affecting stability. Hazardous surroundings, climatic conditions, experience of personnel and proper training must all be taken into account by the operator.
3) The weights of all load handling devices such as hooks, hook blocks, slings, etc., except the hoist rope, shall be considered part of the load. See above.
4) Ratings on outriggers are for either outriggers fully extended and down or fully retracted and down. Ratings for outriggers fully retracted and down will apply for any intermediate outrigger setting.
5) Ratings on rubber depend on 12.00R20 tire capacity, condition of tires and proper inflation pressure (8,9 bar). Loads on rubber may be trans-ported at a maximum speed of 4,0 km/h on a smooth, hard, level surface with boom retracted to the shortest length possible and centered over front. Do not use jib with crane on rubber.
6) For operating radius not shown, use load rat-ing of next larger radius. 7) The maximum deck load only is 7260 kg. Com-bined boom and deck loads are not permitted on rubber.
8) Do not induce any external side loads to boom or jib.
MAIN BOOM LOAD RATINGS ON OUTRIGGERSExtended and Down 360° or Retracted and Down Front/Rear
5,3 m BOOM 8,8 m BOOM 1 2,2 m BOOM 1 5,2 m BOOM
Radius(m)
RatedLoad(kg)
BoomAngle(deg)
RatedLoad(kg)
BoomAngle(deg)
RatedLoad(kg)
BoomAngle(deg)
RatedLoad(kg)
BoomAngle(deg)
MAIN BOOM LOAD RATINGS ON OUTRIGGERSRetracted and Down 360°
5,3 m BOOM 8,8 m BOOM 1 2,2 m BOOM 1 5,2 m BOOM
Radius(m)
RatedLoad(kg)
BoomAngle(deg)
RatedLoad(kg)
BoomAngle(deg)
RatedLoad(kg)
BoomAngle(deg)
RatedLoad(kg)
BoomAngle(deg)
1 ,82,43,03,74,34,95,56,16,77 ,37 ,98,59,19,8
10,411 ,011 ,211 ,612,212,813,414,3
1 ,82,43,03,74,34,95,56,16,77 ,37 ,98,59,19,8
10,411,011,211,612,212,813,414,3
65574835
0 – – – – – – – – – – – – – – – – –
65574835
0 – – – – – – – – – – – – – – – – –
– –67 ,562,557 ,552,547413425
0 – – – – – – – – – – –
– –67 ,562,557 ,552,547413425
0 – – – – – – – – – – –
1 3 6001 3 37 51 1 7 251 0 1 255940
1 8 90 – – – – – – – – – – – – – – – – –
––
7 6857 6857 6857 30063355285450038853240
–––––––––––
– – – –68
64,561 ,558
54,551474338322515,5 0 – – – – –
– – – –68
64,561 ,558
54,551474338322515,5 0 – – – – –
– – – – – –68,56663
60,5585552
48,545,542
40,5383429
23,5 0
– – – – – –68,56663
60,5585552
48,545,542
40,5383429
23,5 0
– – – –
7 21 0657 5597 051 7 5453539253450304027 20240521 7 519701910
– –
– – –
– –
– – – –
54504905432538553420303527 20241 521951995193518201660152514001240
13 60011 35081 6059554585
– – – – – – – – – – – – – – – – –
– – – –
41 65352530302630230520251 7 7 01 5501 3651 1 851050930895– – – – –
– – – – – –
287 025052205195517 401540136011 8510559409058357 45665595500
– –
7 21 05480449037 6531 85268022901 97 01 7 1 5
– – – – – – – – – – –
THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE. The individual crane’s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane.
26
Load chart DIN/ISO
15°30°
SIDE
FRONT REAR
15°30°
SIDE
NOTES:JIB CAPACITY IS LIMITED BY BOTH STRUCTURAL CAPACITY CHART AND MAIN CAPACITY CHART.
SHADED AREAS ARE GOVERNED BY STRUCTURAL STRENGTH, DO NOT RELY ON TIPPING.
OPERATION OF THIS EQUIPMENT IN EXCESS OF RATING CHARTS AND DISREGARD OF INSTRUCTIONS IS DANGEROUS AND VOIDS WARRANTY.
1) The rated loads are the maximum lift capacities as determined by operating radius, boom length and boom angle. The operating radius is the horizontal distance from a projection of the axis of rotation to the supporting surface, before loading, to the center of vertical hoist line or tackle with load applied.
2) The rated loads shown on outriggers do not exceed 80% of actual tipping. The rated loads shown on rubber do not exceed 75% of actual tipping. These ratings are based on freely suspended loads with the crane leveled, standing on a firm, uniform supporting surface. Practical working loads depend on supporting surface, operating radius and other factors affecting stability. Hazardous surroundings, climatic conditions, experience of personnel and proper training must all be taken into account by the operator.
3) The weights of all load handling devices such as hooks, hook blocks, slings, etc., except the hoist rope, shall be considered part of the load. See above.
4) Ratings on outriggers are for either outriggers fully extended and
down or fully retracted and down. Ratings for outriggers fully re-tracted and down will apply for any intermediate outrigger setting.
5) Ratings on rubber depend on 12.00R20 tire capacity, condition of tires and proper inflation pressure (8,9 bar). Loads on rubber may be transported at a maximum speed of 4,0 km/h on a smooth, hard, level surface with boom retracted to the shortest length pos-sible and centered over front. Do not use jib with crane on rubber.
6) For operating radius not shown, use load rating of next larger radius. 7) The maximum deck load only is 7260 kg. Combined boom and deck loads are not permitted on rubber.
8) Do not induce any external side loads to boom or jib.
Radius (m)
MAIN BOOM ON RUBBERAny Boom Length
Front Rating (kg) 360° Rating (kg)
4,6 m FIXED JIB CAPACITIES ON EXTENDED OUTRIGGERSMain BoomAngle (deg)
Jib Offset Angle0° 15° 30°
To 1 2,2 mMain Boom
To 1 5,2 mMain Boom
To 1 2,2 mMain Boom
To 1 5,2 mMain Boom
To 1 2,2 mMain Boom
80906525521 04440364030802620221 01880161513951265112097 58657 7 07 407 00620550490405
6965605550454035302520151050
3400325527 202350207 51 87 01 7 1 51 5801 4451 3301 2551 2051 1 651 1 401 1 35
31 80257 021 60187 01655141 012401 1 1 510059158608207 857 7 07 65
2485221 5201 0186017 351640154014601390130512451190
–––
239520451 7 851 5951 4551 3251 1 801 06597 5905855815– – –
17 90167 015901540146014201390137 01360
––––––
To 1 5,2 mMain Boom
1 7 901 67 01 5901 4551 3451 2651 1 451 050
955– – – – – –
1 ,82,43,03,74,34,95,56,16,77 ,37 ,98,59,19,810,411 ,011 ,211 ,612,212,813,414,3
7 07 05230406033652685236519451620136511609908857 4563553044540537 0300230190–
THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE. The individual crane’s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane.
Grove YB5515-2 27
Transportation and lifting data
LOAD DISTRIBUTION CHART
Maximum Allowable UniformlyDistributed Load
CAB
1
2
FRONT TANK SUPPORT (REF)
AREA 14.01 m (43.2 sq ft) 5985 kg (13,195 lb)
AREA 22.15 m (23.1 sq ft) 3087 kg (6805 lb)
TOTAL 6.16 m (66.3 sq ft) 9072 kg (20,000 lb
1. Maximum travel speed with any or all loads - 4.0 km/h (2.5 MPH)2. Loads to be transported on smooth level firm surfaces only.3. Boom must be retracted and in center forward position.4. Any combination or total of areas 1 & 2 may be used.5. Lifting is not permitted when carry deck is loaded except for loading and unloading carry deck.6. Rated pick and carry loads may be transported on deck area 1 provided the load is cribbed directly on the frame rails.
2
2
2
TRANSPORTATION AND LIFTING DATA - YB5515-2
CAPACITY-TONNES [TONS]
TIE DOWNLIFTLIFTLIFT TOW
SIDE DOWNFORE& AFT
4
4 X
A
B
X X X
FITT
ING
NO
. / U
NIT
LIFT
TOW
TIE
DOW
N
9.1[10]
1.8[2]
27.2[30]
27.2[30]
27.2[30]
0.9[1]
BOOM CWT1. LIFTING OF ENTIRE CRANE OR MAJOR CRANE ASSEMBLIES MUST BE ACCOMPLISHED BY UTILIZING SPECIFIC FITTINGS INDICAT ED ON ADJACENT CHART. USE OF FITTINGS FOR PURPOSES OTHER THAN THOSE DESIGNATED ON CHART IS PROHIBITED. FITTING CAPACITIES ARE MAXIMUM A LLOWABLE LOADS PER INDIVIDUAL FITTING.2. RIGGING PERSONNEL SHALL BE RESPONSIBLE FOR PROPER SELECTION A ND PLACEMENT OF ALL SLINGS A ND LOAD HANDLING DEVICES.3. DIMENSIONS A ND WEIGHTS SHOWN ARE ESTIMATED FOR LARGEST CONFIGURATION AVAILABLE. WEIGHTS DO NOT INCLUDE BOOM EXTENSION A ND OR JIB, UNLESS OTHERW ISE INDICATED.4. RIGGING PERSONNEL SHALL VERIFY DIMENSIONS AS REQUIRED FOR CLEARANCE.5. DO NOT USE COUNTERW EIGHT LIFT LOCATIONS OR BOOM SLING POINT FOR LIFTING OR TIE DOWN OF ENTIRE CRANE.
80055769G7
BB
50' BOOM WEIGHT 1987 kg(4381 lb)
41' BOOM WEIGHT 1671 kg(3685 lb)
5567 mm(219.2")
BB
5701 mm(224.4")
2510 mm(98.8")
C.G.
2642 mm (104")
C.G.
6791 mm(385.5")
2495 mm (98.2")
A
4597 mm(181.0")
G.V.W. 14 436 kg (31,804 lb)
1128 mm(44.4")
C.G.
A
4x Ø76.2 mm (3")
TOTAL UNIT W/ 50' BOOM AND BOOM EXTENSION
LOAD DISTRIBUTION CHART
Maximum Allowable UniformlyDistributed Load
CAB
1
2
FRONT TANK SUPPORT (REF)
AREA 14.01 m (43.2 sq ft) 5985 kg (13,195 lb)
AREA 22.15 m (23.1 sq ft) 3087 kg (6805 lb)
TOTAL 6.16 m (66.3 sq ft) 9072 kg (20,000 lb
1. Maximum travel speed with any or all loads - 4.0 km/h (2.5 MPH)2. Loads to be transported on smooth level firm surfaces only.3. Boom must be retracted and in center forward position.4. Any combination or total of areas 1 & 2 may be used.5. Lifting is not permitted when carry deck is loaded except for loading and unloading carry deck.6. Rated pick and carry loads may be transported on deck area 1 provided the load is cribbed directly on the frame rails.
2
2
2
TRANSPORTATION AND LIFTING DATA - YB5515-2
CAPACITY-TONNES [TONS]
TIE DOWNLIFTLIFTLIFT TOW
SIDE DOWNFORE& AFT
4
4 X
A
B
X X X
FITT
ING
NO
. / U
NIT
LIFT
TOW
TIE D
OWN
9.1[10]
1.8[2]
27.2[30]
27.2[30]
27.2[30]
0.9[1]
BOOM CWT1. LIFTING OF ENTIRE CRANE OR MAJOR CRANE ASSEMBLIES MUST BE ACCOMPLISHED BY UTILIZING SPECIFIC FITTINGS INDICAT ED ON ADJACENT CHART. USE OF FITTINGS FOR PURPOSES OTHER THAN THOSE DESIGNATED ON CHART IS PROHIBITED. FITTING CAPACITIES ARE MAXIMUM A LLOWABLE LOADS PER INDIVIDUAL FITTING.2. RIGGING PERSONNEL SHALL BE RESPONSIBLE FOR PROPER SELECTION A ND PLACEMENT OF ALL SLINGS A ND LOAD HANDLING DEVICES.3. DIMENSIONS A ND WEIGHTS SHOWN ARE ESTIMATED FOR LARGEST CONFIGURATION AVAILABLE. WEIGHTS DO NOT INCLUDE BOOM EXTENSION A ND OR JIB, UNLESS OTHERW ISE INDICATED.4. RIGGING PERSONNEL SHALL VERIFY DIMENSIONS AS REQUIRED FOR CLEARANCE.5. DO NOT USE COUNTERW EIGHT LIFT LOCATIONS OR BOOM SLING POINT FOR LIFTING OR TIE DOWN OF ENTIRE CRANE.
80055769G7
BB
50' BOOM WEIGHT 1987 kg(4381 lb)
41' BOOM WEIGHT 1671 kg(3685 lb)
5567 mm(219.2")
BB
5701 mm(224.4")
2510 mm(98.8")
C.G.
2642 mm (104")
C.G.
6791 mm(385.5")
2495 mm (98.2")
A
4597 mm(181.0")
G.V.W. 14 436 kg (31,804 lb)
1128 mm(44.4")
C.G.
A
4x Ø76.2 mm (3")
TOTAL UNIT W/ 50' BOOM AND BOOM EXTENSION
THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE. The individual crane’s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane.
28
Rigging chart
MAXIMUM PERMISSIBLE SINGLE LINE PULL = 10,000 LB
WIRE ROPE: 9/16" Diameter 6 X 19 BrightMinimum required breaking strength = 37,000 lb
RATING REDUCTIONS FOR LOADHANDLING DEVICES INSTALLED (lb)
MAIN BLOCKHOOK & BALLJIB STOWED
15' JIB DEPLOYED
FROM MAIN BOOM356*105*
NO REDUCTION700
FROM JIB NOT APPLICABLE
105 NOT APPLICABLE
NO REDUCTION
RIGGING CHART
4-PART0-30,000 lb
1-PART0-7500 lb
* Refer to rating plate for actual weight
MAXIMUM PERMISSIBLE SINGLE LINE PULL = 4536 kg
WIRE ROPE: 1 4mm Diameter 6 X 19 BrightMinimum required breaking strength = 164.6 kN
RATING REDUCTIONS FOR LOADHANDLING DEVICES INSTALLED (kg)
MAIN BLOCKHOOK & BALLJIB STOWED
JIB DEPLOYED
FROM MAIN BOOM166* 40*
NO REDUCTION320
FROM JIB NOT APPLICABLE
40* NOT APPLICABLE
NO REDUCTION
RIGGING CHART
4-PART0-13 610 kg
1 -PART0-3400 kg
* Refer to rating plate for actual weight
4,6 m
MAXIMUM PERMISSIBLE SINGLE LINE PULL = 10,000 LB
WIRE ROPE: 9/16" Diameter 6 X 19 BrightMinimum required breaking strength = 37,000 lb
RATING REDUCTIONS FOR LOADHANDLING DEVICES INSTALLED (lb)
MAIN BLOCKHOOK & BALLJIB STOWED
15' JIB DEPLOYED
FROM MAIN BOOM356*105*
NO REDUCTION700
FROM JIB NOT APPLICABLE
105 NOT APPLICABLE
NO REDUCTION
PIVOT HOLE PATTERN+80°
+40°
0°-15°-30°
PIVOT
G7 80055637
LOW HEADROOM OPERATION(35° MAX. BOOM ANGLE;SINGLE PART LINE ONLY)
LOW HEADROOM OPERATION(55° MAX. BOOM ANGLE)
STANDARD HEADROOM OPERATION(80° MAX. BOOM ANGLE)NO OFFSET JIB OPERATION(75° MAX. BOOM ANGLE)
OFFSET JIB OPERATION(80° MAX. BOOM ANGLE)
RIGGING CHART
4-PART0-30,000 lb
1-PART0-7500 lb
* Refer to rating plate for actual weight
THIS CHART IS ONLY A GUIDE AND SHOULD NOT BE USED TO OPERATE THE CRANE. The individual crane’s load chart, operating instructions and other instructional plates must be read and understood prior to operating the crane.
Grove YB5515-2 29
Symbols glossary
Drive
RotationElectrical system
Suspension
Fuel tank capacity
Tires
Engine
Brakes
Outrigger controls
Axles Outriggers
Transmission
Frame
Steering
Lights
Boom elevation
Cab
Swing
Hydraulic system
Hoist
Boom nose
Radius
Boom extension
Boom length
Grade
Gear
Boom
Counterweight
Speed
Oil
Extension
HookblockH
Heavy duty jib
30
Notes
Grove YB5515-2 31
Notes
©2013 ManitowocForm No. YB5515-2 PGPart No. 13-013 /2M /1213 www.manitowoccranes.com
This document is non-contractual. Constant improvement and engineering progress make it necessary that we reserve the right to make specification, equipment, and price changes without notice. Illustrations shown may include optional equipment and accessories and may not include all standard equipment.
Regional offices
ChinaShanghai, China Tel: +86 21 6457 0066Fax: +86 21 6457 4955
Greater Asia-Pacific Singapore Tel: +65 6264 1188 Fax: +65 6862 4040
Europe, Middle East, Africa Dardilly, France Tel: +33 (0)4 72 18 20 20 Fax: +33 (0)4 72 18 20 00
Americas Manitowoc, Wisconsin, USA Tel: +1 920 684 6621 Fax: +1 920 683 6277
Shady Grove, Pennsylvania, USA Tel: +1 717 597 8121 Fax: +1 717 597 4062
Regional headquarters
Manitowoc Cranes
ChinaBeijingChengduGuangzhouXian
Greater Asia-PacificAustraliaBrisbaneMelbourneSydneyIndiaChennaiDelhiHyderabadPuneKoreaSeoulPhilippinesMakati CitySingapore
FactoriesBrazilPasso FundoChinaTaiAnZhangjiagangFranceCharlieuMoulinsGermanyWilhelmshavenIndiaPuneItalyNiella TanaroPortugalBaltarFânzeresUSAManitowoc Port WashingtonShady Grove
AmericasBrazilAlphavilleMexicoMonterreyChileSantiago
Europe, Middle East, AfricaFranceBaudemontCergyDecinesGermanyLangenfeldItalyLainateNetherlandsBredaPolandWarsawPortugalBaltarRussiaMoscowSouth AfricaJohannesburgU.A.E.DubaiU.K.Buckingham
Recommended