View
7
Download
0
Category
Preview:
Citation preview
Fluoropolymers are some of themost versatile engineeringmaterials known and, since theirdiscovery 70 years ago, have beenused in nearly every field ofmodern industry, technology, and
science. Their non-stick proper-ties became commonly recog-
nized by the consumingpublic when E. I. DuPont
began marketing his“Teflon®” brand productfor use on cookware, as afiber treatment for stainresistance, and in otherhousehold applications.
Fluoropolymer materialis recognized for itsexcellent resistance to
heat — up to 500°F con-tinuously. Lesser known
is its usefulness inextremely cold tempera-
tures — well below -200°F. Itwill remain reasonably flexible
to -110°F.
Fluoropolymer123c
Fluoropolymer TubingPTFE, FEP, & PFA . . . . . . . . . . . . . . . . .2
AWG & Fractional Fluoropolymer Tubing
PTFE tubing in three wallthicknesses . . . . . . . . . . . . . . . . . . . . .4
Coiltef™Coiled FEP tubing . . . . . . . . . . . . . . .5
Corrtef™Corrugated FEP tubing . . . . . . . . . .6
Contef™Convoluted PTFE tubing . . . . . . . . .7
Stainless Steel Overbraided Smooth core PTFE tubing withoverbraiding . . . . . . . . . . . . . . . . . . . .8
Pureloc®
PFA compression fittings . . . . . . . .9
Because fluoropolymers arealmost universally inert toindustrial chemicals and solvents,their use for corrosion protectionhas become one of their largestgrowth areas.With few exceptions,fluoropolymer tubing can handlevirtually any corrosive chemical inuse today.
NewAge® Industries offers one ofthe widest assortments of tubingproducts made of fluoropolymersby any supplier.We can meet mostany need for straight tubing,thinner-walled AWG andfractional sizes (for electricalinsulation and jacketing),corrugated (for increased bendradii), convoluted (for easier flushcleaning), or retractable coiledfluoropolymer tubing, along withinjection-molded PFA com-pression fittings (see page 9). AndNewAge now offers stainless steeloverbraided PTFE hose fordemanding applicationsinvolving automotive, chemical,and petrochemical uses. ■
■ Adhesives & Hot Glue Delivery ■ Automotive ■ Cable Bundling ■Chemical Transfer ■ Connector Sleeves ■ Corrosives ■ Cryogenics ■Deionized Water Transfer ■ Environmental Sampling ■ FlameRetardant Covering ■ Food & Beverage Processing ■ InternalSheathing ■ Laboratory & Medical Uses ■ Lighting Covers ■ PaintSpray Systems ■ Petrochemical Transfer ■ Pharmaceutical Processingand Packaging ■ Pure Air Systems ■ Pure Water & Fluid Systems ■Push-Pull Cable Jacketing ■ Robotics ■ Sight Glass (FEP) ■ SolventTransfer ■ Wire Insulation ■ More
Applications
Sign up for our eNewsletter at www.newageindustries.com/extrusionsFluid Transfer Specialists ®
2 www.newageindustries.com
123cFluoropolymer Tubing P T F E , F E P , & P F A F o r m u l a t i o n s
■ Chemically inert; low permeability
■ Manufactured from FDA-sanctioned ingredients for usewith food contact surfaces
■ Lowest coefficient of friction of any solid material
■ Widest service temperature of any plastic tubing (-275°F to 500°F)
■ Excellent electrical and weathering properties; non-flammable
■ Made without plasticizer which can leach into critical streams
■ Ultra-high-purity grades available for the semiconductor industry
Notes
Almost totally inert, FLUOROPOLYMERtubing can be used with virtually allindustrial solvents, chemicals, and corrosivematerials, even at elevated temperatures. Itdoes, however, react with fluorine, moltensodium hydroxide, and molten alkali metals.
FLUOROPOLYMER tubing can be steamor chemically sterilized in-line with anyindustrial cleaner, solvent, or sterilizingmethod.
FLUOROPOLYMER’s non-stick propertyallows transport of viscous, sticky materialswithout line clogging. It also offersoutstanding aging resistance.
PTFE’s translucent white color will varynaturally from lot to lot, however the qualityand physical properties do not change. FEPand PFA are clearer and can be heat sealedand heat bonded.
Permanent color striping, etching, andlonger-than-listed lengths are availablethrough minimum order. Polyethylene-jacketed, thin-wall fluoropolymer tubing, forlow-cost purity, is also available throughminimum order — call for details.
Recommended Fittings
■ Pureloc® injection molded tube fittings on pg. 9
Physical Properties**PTFE FEP PFA
Hardness, Shore D 50-65 55 60Tensile Strength, psi 3000-5000 3500 3500Elongation at Break, % 200-400 300 300Brittle Temperature, °F <-400 <-400 <-329Max. Continuous Operating Temp., °F 500 400 500
**Values listed are typical for the material used in manufacture, except wherenoted, and are meant only as a guide to aid in design. Field testing should beperformed to find the actual values for your application.
What’s the difference?
PTFE (Polytetrafluoroethylene) a fluorocarbon-based polymer, is a resinsupplied in powdered form, which is mixed, preformed, and extruded into apaste, and then finally tubing. PTFE tubing can be used in a large variety ofapplications due to its high chemical resistance, high and low temperaturecapability, resistance to weathering, electrical and thermal insulation, andlowest coefficient of friction of any solid material. The tubing is translucentwhite in color.
FEP (Fluorinated Ethylene Propylene) resin is pelletized for its hot-meltextrusion process. FEP tubing is known for its gas and vapor permeabilityproperties and excellent UV transmission ratings. While very similar incomposition to PTFE, there are a few notable differences. FEP has a lower heatshrink temperature and is clearer and more flexible than PTFE.
PFA (Perfluoroalkoxy) resin, like FEP, belongs to a class of melt-processiblefluoroplastics. PFA tubing is also known for its gas and vapor permeabilityproperties and excellent UV transmission ratings. It is similar in composition toFEP but has better heat resistance and a smoother surface. It, too, is clearer andmore flexible than PTFE.
Custom Services■ Cut■ Size
■ Color■ Overbraid
Call for more information: 800-506-3924or 215-526-2300
Made in U.S.A.
Meet Some of NewAge Industries’ OwnersThrough an EmployeeStock Ownership Plan(ESOP), we’re partowners in the company,and that makes yoursatisfaction an invest-ment in our future.
Thurman NealPlastic Manu-facturing/Owner7 years
Deanna FabrizioMarketingAssistant/Owner3 years
Michael HorvathTechnical SalesRep./Owner4 years
■ Heat-Form**FEP & PFA only
3www.newageindustries.com
123c Fluoropolymer Tubing P T F E , F E P , & P F A F o r m u l a t i o n s
ID(IN.)
1/321/321/161/163/321/81/83/163/161/41/45/165/163/83/87/167/161/21/29/169/165/85/8
11/163/43/47/811
1-1/41-1/2
2
OD(IN.)
1/163/321/83/165/323/161/41/45/165/163/83/87/167/161/21/29/169/165/85/8
11/1611/163/43/4.8307/81
1.1001 1/81 3/81- 5/82-1/8
STANDARDLENGTH
(FT.)�100100
50, 10050, 10050, 10050, 10050, 10050, 10050, 10050, 100
25, 50, 10025, 50, 10025, 50, 10025, 50, 10025, 50, 10025, 50, 10025, 50, 10025, 50, 10025, 50, 10025, 50, 10025, 50, 10025, 50, 10025, 50, 10025, 50, 100
5, 10 Straight5, 10 Straight5, 10 Straight
5, 10�� Straight5, 10 Straight5, 10 Straight5, 10 Straight5, 10 Straight
PART NO.PTFE
300 0074*300 0151300 0228300 0305300 0382300 0459300 0536300 0690300 0767300 0844300 0921300 0998300 1075300 1152300 1229300 1306300 1383300 1460300 1537300 1614300 1691*300 1768300 1845300 1922300 1999*
300 2307
PART NO.FEP
310 0048310 0090310 0167310 0244310 0321310 0398310 0552310 0629310 0706310 0783310 0860310 0937*310 1014310 1091310 1168
310 1322310 1399
310 1707310 1784310 1938310 2015310 2169310 2246310 2323310 2477310 2631*310 2708
PART NO.PFA
320 0176
320 0330320 0407320 0484320 0561
320 0715320 0792320 0869
320 1100
320 1254320 1331320 1408320 1485*
320 1716
320 2255
WALL(IN.)
.015
.030
.030
.063
.030
.030
.063
.030
.063
.030
.063
.030
.063
.030
.063
.030
.063
.030
.063
.030
.063
.030
.063
.032
.040
.063
.063
.050
.063
.063
.063
.063
ID(MM)
2468101214
OD(MM)
46810121416
STANDARDLENGTH (FT.)�
50, 10050, 10050, 100
25, 50, 10025, 50, 10025, 50, 10025, 50, 100
PART NO.PTFE
301 0175301 0350301 0525301 0700301 0875*301 1050*301 1225
PART NO.FEP
311 0177311 0352311 0527311 0702311 0877311 1052
PART NO.PFA
321 0354321 0529321 0704321 0879*
WALL(MM)
1111111
FLUOROPOLYMER TUBING – Metric Sizes
*Limited stock item; lead times and minimums apply — call for details.�Sold by standard coil length only.Add length suffix to part number when ordering. Example: 50 ft. of 2mm I.D. x 4mm O.D. PTFE is part number 301 0175-50.NOTE: Orders for 50 ft. lengths of PTFE tubing may be filled with a maximum of two lengths of product totaling 50 ft.Orders for 100 ft. lengths of PTFE tubing may be filled with a maximum of three lengths of product totaling 100 ft.All FEP and PFA lengths are supplied in single-section packages.BOLD indicates the critical dimension for fittings application.
*Limited stock item; lead times and minimums apply — call for details.�Sold by standard coil length only.��10 ft. length available in FEP and PFA only.Add length suffix to part number when ordering. Example: 50 ft. of 1/16” x I.D.1/8” O.D. PTFE is part number 300 0228-50.NOTE: Orders for 50 ft. lengths of PTFE tubing may be filled with a maximum of two lengths of product totaling 50 ft.Orders for 100 ft. lengths of PTFE tubing may be filled with a maximum of three lengths of product totaling 100 ft.All FEP and PFA lengths are supplied in single-section packages.BOLD indicates the critical dimension for fittings application.
FLUOROPOLYMER TUBING – Inch Sizes
AWG and Fractional sizes are found on page 4.
BURST PSI AT 70°F
196214871983119710021511756
1220606
1024506882435774381690339622305567278520255305
235
BURST PSI AT 70°F
196214871983119710021511756
1220606
1024506882435774381
339622
520255305447392235349286
186
WORKINGPSI AT 70°F
38929539323819930015024212020010017586
15075
67125
10050619080476957
37
BURST PSI AT 70°F
1859
149712531899
945
7581280
633
1968
862424778381
650
294
WORKINGPSI AT 70°F
369
297249380190
150260125
195
17184
16075
132
58
WORKINGPSI AT 70°F
38929539323819930015024212020010017586
15075
13767
12560
11255
1005061
47
■ Note that sizes are listed first due to the variety of materials offered
4 www.newageindustries.com
123cAWG & Fractional PTFE TubingP T F E F o r m u l a t i o n T u b i n g i n T h r e e W a l l T h i c k n e s s e s
■ High dielectric strength — 500 Volts/mil
■ Excellent volume resistivity — 1018 OHM-CM H2
■ Unaffected by thermal aging at 400°F
■ Non-flammable and practically smokeless when incinerated
■ Widest service temperature available (-275°F to 500°F)
Meets Specifications:MIL-I-22129C, ASTM D-3295-81A, AMS 3653C, AMS 3654, AMS 3655
Notes
Outstanding chemical andtemperature resistance, coupledwith fluoropolymer’s lowcoefficient of friction, makesAWG & FRACTIONAL PTFE tubingan excellent choice on primaryconductors as protection fromchemical contact or temperatureextremes.
AWG & FRACTIONAL PTFEtubing resists melt-off bysoldering irons when makingelectrical terminations, especiallyin close-quarter installations.
The product’s outstandingthermal properties offercontinuous use from cryogenictemperatures up to 500°F. It isalso non-aging, so brittleness iseliminated.
PTFE is translucent white incolor, however, the degree ofwhiteness will naturally varyfrom lot to lot. This color variancehas no bearing on the material’squality or physical properties.
Physical Properties**
Hardness, Shore D 50-55Specific Gravity 2.15Tensile Strength, psi 3200Elongation at Break, % 250-450Brittle Temperature <-275°FMax. Operating Temp. 500°F
**Values listed are typical for the materialused in manufacture, except where noted,and are meant only as a guide to aid indesign. Field testing should be performed tofind the actual values for your application.
AWG./IN.
SIZE3028262423222120191817161514131211109876543210
1/8"3/16"1/4"
5/16"3/8"
7/16"1/2"5/8"3/4"7/8"1"
STANDARDLENGTH
(FT.)�100, 1000100, 1000100, 1000100, 1000100, 1000100, 1000100, 1000100, 1000100, 1000100, 1000100, 1000100, 1000100, 1000100, 500100, 500100, 500100, 500100, 500100, 500
100100100100100100100100100
100 Random100 Random100 Random100 Random100 Random100 Random100 Random100 Random
5 Straight5 Straight5 Straight
STANDARDWALL(IN.)
.007/.011
.007/.011
.007/.011
.010/.014
.010/.014
.010/.014
.010/.014
.013/.019
.013/.019
.013/.019
.013/.019
.013/.019
.013/.019
.013/.019
.013/.019
.013/.019
.013/.019
.013/.019
.016/.024
.016/.024
.016/.024
.016/.024
.016/.024
.016/.024
.016/.024
.016/.024
.016/.024
.016/.024
.016/.024
.016/.024
.016/.024
.016/.024
.019/.031
.019/.031
.019/.031
.024/.036
.027/.043
.027/.043
.027/.043
PARTNO.
330 0101330 0213330 0325330 0437330 0549330 0661330 0773330 0885330 0997330 1109330 1221330 1333330 1445330 1557330 1669330 1781330 1893330 2005330 2117330 2229330 2341330 2453330 2565330 2677330 2789330 2901330 3013330 3125331 0167331 0265331 0363331 0461331 0566331 0664331 0769331 0860331 0958331 1056331 1154
THINWALL (IN.)
.007/.011
.007/.011
.007/.011
.007/.013
.007/.013
.007/.013
.007/.013
.009/.015
.009/.015
.009/.015
.009/.015
.009/.015
.009/.015
.009/.015
.009/.015
.009/.015
.009/.015
.009/.015
.012/.018
.012/.018
.012/.018
.012/.018
.012/.018
.012/.018
.012/.018
.012/.018
.012/.018
.012/.018
.012/.018
.012/.018
.012/.018
.012/.018
.015/.025
.015/.025
.015/.025
.020/.030
.025/.035
PARTNO.
330 0094330 0206330 0318330 0430330 0542330 0654330 0766330 0878330 0990330 1102330 1214330 1326330 1438330 1550330 1662330 1774330 1886330 1998330 2110330 2222330 2334330 2446330 2558330 2670330 2782330 2894330 3006330 3118331 0160331 0258331 0356331 0454331 0559331 0657331 0762331 0853331 0951
LIGHTWALL(IN.)
.004/.008
.004/.008
.004/.008
.004/.008
.004/.008
.004/.008
.004/.008
.004/.008
.004/.008
.004/.008
.004/.008
.004/.008
.006/.010
.006/.010
.006/.010
.006/.010
.006/.010
.006/.010
.006/.010
.006/.010
.007/.013
.007/.013
.007/.013
.007/.013
.007/.013
.007/.013
.009/.015
.006/.010
.007/.013
.007/.013
.009/.015
.012/.018
.015/.021
.015/.021
PARTNO.
330 0087
330 0311330 0423330 0535330 0647330 0759330 0871330 0983330 1095330 1207330 1319330 1431330 1543330 1655330 1767330 1879330 1991330 2103330 2215330 2327330 2439330 2551330 2663330 2775330 2887330 2999330 3111331 0153331 0251331 0349331 0447331 0552331 0650331 0755
Recommended Fittings
■ Pureloc® injection molded tube fittings, pg. 9
ID (IN.)MIN/MAX
.010/.015
.013/.018
.016/.021
.020/.026
.023/.029
.026/.032
.029/.035
.032/.038
.036/.042
.040/.046
.045/.052
.051/.058
.057/.065
.064/.072
.072/.081
.081/.091
.091/.101
.102/.112
.114/.124
.129/.139
.144/.155
.162/.174
.182/.195
.204/.218
.229/.244
.258/.273
.289/.305
.325/.342
.120/.130
.188/.198
.250/.260
.313/.332
.375/.394
.438/.458
.500/.520
.625/.650
.750/.775
.875/.9271.000/1.030
*Available in 100 foot length only.�Sold by standard length only.Add length suffix to part number when ordering. Example: 100 ft. of AWG 30, thin wall tubing is partnumber 330 0094-100.Note: 500 and 1000 ft. lengths are furnished on spools and may have up to three splices.
Made in U.S.A.
Custom Services■ Cut■ Size
■ Color■ And More
Call for more information800-506-3924
*
*
*
*
5www.newageindustries.com
123c
Made in U.S.A.
■ Made of chemically inert clear FEP
■ Manufactured from FDA-sanctioned ingredients
■ Heat set into a retractable coil; excellent recoil memory
■ Offers all the chemical and electrical insulation properties ofstandard FEP fluoropolymer tubing
■ Allows flexibility to otherwise semi-rigid fluoropolymer tubing
■ All Coiltef is made to order — call for details
Coiltef ™
C o i l e d F E P T u b i n g
Notes
Almost totally inert, COILTEF can be used withall industrial solvents, chemicals, and corrosivematerials even at elevated temperatures. It does,however, react with fluorine, molten sodiumhydroxide, and molten alkali metals.
Fluoropolymer’s non-stick property allowstransport of viscous, sticky material without lineclogging. It also offers outstanding agingresistance.
COILTEF is manufactured through afabrication process which heat sets the coils. Thecoils should remain stable up to 200°F. At highertemperatures the coils will begin to relax and losetheir set. If the application involves elevatedtemperatures, in-house testing is recommended.
COILTEF may be steam or chemically sterilizedin-line with any industrial cleaner, solvent, orsterilizing method. Care should be taken withsteam sterilization to prevent coil relaxation.Testing is recommended.
COILTEF can be manufactured from .085" to1/2" tubing I.D. The coil diameter can beproduced from 3/4" O.D. to 4" O.D.
PFA-formulated COILTEF is also available byspecial order.
Physical Properties**
Hardness, Shore D 55Tensile Strength, psi 3500Elongation at Break, % 300Brittle Temperature, °F�� <-400Max. Operating Temp., °F�� 400
**Values listed are typical for the material used inmanufacture, except where noted, and are meant only asa guide to aid in design. Field testing should beperformed to find the actual values for your application.��Temperatures are for standard extruded (non-coiled)tubing. See “Notes” for additional information.
C
A
E
BD
C
AID
(IN.)
1/161/83/161/43/8
BOD(IN.)
3/161/45/163/81/2
D^O.D. OF
COIL(IN.)
1-1/81-1/22-1/42-3/8
4
E^MAXIMUM AVAILABLE EXPANDEDLENGTH; NOT INCLUDING TAILS
(IN.)
12, 24, 48, 7212, 24, 48, 7212, 24, 48, 7212, 24, 48, 72
12, 24, 48
PARTNO.
360 0072*360 0149*360 0226*360 0303*360 0457*
*Non-stock item; lead times and minimums apply — call for details.^These dimensions are nominal.Add length suffix to part number when ordering. Example: 12 inches of 1/16” I.D. x 3/16”O.D. tubing is part number 360 0072-12.The retracted length is approximately 1/4 of the maximum expanded length excluding tails.Wall thickness for all standard sizes is 1/16. Tail length (item C) is 6” for all listed sizes.BOLD indicates the critical dimension for fittings application.
Recommended Fittings
■ Pureloc® injection molded tube fittings, pg. 9
Custom Services■ Cut■ Size
■ And More
Call for more information800-506-3924
More NewAgeIndustries’ Owners
Ann StanleyFittings/Owner2 years
Josh ReamSilicone Manufac-turing Supv./Owner11 years
Marty GolinTechnical SalesRep./Owner6 years
6 www.newageindustries.com
123cCorrtef ™
C o r r u g a t e d F E P T u b i n g
■ Made from FEP fluoropolymer tubing
■ Corrugations allow a nearly zero bend radius — easily flexed
■ Can be extended or compressed without affecting the tube’s I.D.
■ Made from FDA-sanctioned ingredients
■ Made without plasticizers which can leach into critical streams
■ Has all the chemical and electrical properties ofstraight-walled FEP tubing
■ May be overbraided with Kevlar® for higher pressures^
Notes
Vacuum Service: 29.9 in./Hg.Bend Diameter: 1/2 of tubing I.D.
Optimal flow is achieved and turbulenceminimized by passing fluids through CORRTEF inthe direction of the corrugation angles (asillustrated).
CORRTEF is heat sealable, and the cuffs(straight ends) are made to accept standardbarbed fittings. The end may be flared orexpanded to permit shrink-tight connections.
CORRTEF is manufactured in an industrialatmosphere and should be properly sterilized forclean-flow applications. For optimal cleaning ofCORRTEF, the tube should be stretched to itsmaximum length and held vertically (direction offlow: down). Due to the annular corrugations, itmay not be possible to remove all traces ofparticulate from CORRTEF, even under optimalcleaning conditions.
^Overbraiding with Kevlar will permit aminimum increase of six times the listed pressures.Kevlar overbraiding is available for sizes up to7/8” I.D. – call for details.
Physical Properties**
Hardness, Shore D 50-55Tensile Strength, psi 3500Elongation at Break, % 325Brittle Temperature, °F†† <-275Min. Continuous Svc. Brittle Temp., °F�� -100Maximum Operating Temperature, °F�� 400Max. Cont. Svc. Temp., zero pressure, °F�� 200
**Values listed are typical for the material used inmanufacture, except where noted, and are meant only asa guide to aid in design. Field testing should beperformed to find the actual values for your application.��Temperatures are for standard extruded (non-corrugated) tubing.
Recommended Fittings & Clamps ■ Thermobarb® barbed fittings ■ Oetiker® ear type clamps ■ Kwik Clamp™ nylon double bond hose clamps ■ Worm gear clamps
E
BC
DA
Preferred direction of flow
�
AMAX.
ID (IN.)
1/43/81/25/83/47/81
1-1/41-1/2
2
BCUFF
LENGTHNOM. (IN.)*
3/4111
1-1/21-1/2
2222
CWALLNOM.(IN.).015.020.025.025.030.030.035.035.035.040
DCORRUGA-
TION ODREF. (IN.)
3/89/163/4
15/161-1/161-1/41-3/81-5/8
1-13/162-5/8
PARTNO.
340 0075340 0152340 0229340 0306340 0383340 0460340 0537340 0614340 0691340 0768
WORKINGPSI
AT 70°F
62504237302520171512
BURSTPSI
AT 70°F
248200168148120100
80686048
� ‘E’ dimension to be specified at time of order. Maximum overall available length: 12 ft.(including cuffs).*Workable I.D. length of the cuff (straight ends). All lengths will be supplied with ‘B’dimension cuffs.BOLD indicates the critical dimension for fittings application.
➞
Made in U.S.A.
Custom Services■ Overbraid■ And More
Call for more information800-506-3924
■ Cut■ Size
More NewAgeIndustries’ Owners
Chris KoureliasWarehouse/Owner5 years
Khim KimSilicone Manu-facturing/Owner2 years
Steve MidgetteDirector of Finance &Human Resources/Owner17 years
(Length Including Cuffs)
■ Translucent PTFE tubing offers excellent chemical and electrical properties■ Available from stock with or without a stainless steel wire encircling the O.D.■ Wire coil provides increased pressure capability and aids in
electrical grounding■ Easily flexed — spiral construction allows far greater flexibility than
straight wall tubing■ Spiral construction also allows for easier cleaning■ Made from FDA-sanctioned ingredients■ Available to AMS-T-81914/1^ (without wire only)
7www.newageindustries.com
123c Contef ™
C o n v o l u t e d P T F E T u b i n g
Notes
CONTEF’s helical construction aids in selfcleaning when flushed with standard cleaningfluids.
The cuffs (straight ends) are made to acceptstandard barbed fittings. Hose assemblies madeto your specifications are available (see page 69).
PTFE’s color will vary naturally from lot to lot,but the quality and physical properties do notchange.
FEP CONTEF for longer continuous lengths —up to 500 ft. — is available through custom order.
CONTEF Without Wire:Vacuum Service: 27 in./Hg at 72°F.Convolutions are molded into the tubing and
will not cold flow into a straight wall undernormal conditions.
^CONTEF with AMS (Aerospace MaterialSpecifications) is available without wire only andis not stocked — call for details.
CONTEF With Wire:Vacuum Service: 27 in./Hg at 72°F.For high vacuum applications, CONTEF can be
produced with wire on the I.D. — call for details.
Physical Properties**
WITHOUT WITHWIRE WIRE
Hardness, Shore D 55-65 55-65Tensile Strength, min. psi 2000 2000Elongation at Break, % 300 200Brittle Temperature, °F�� <-275 <-110Max. Operating Temperature, °F�� 500 350Max. Cont. Svc.Temp., zero pressure, °F�� 450 350
**Values listed are typical for the material used in manufacture,except where noted,and are meant only as a guide to aid in design.Field testing should be performed to find the actual values for yourapplication.��Temperatures are for standard extruded (non-convoluted) tubing.
Recommended Fittings & Clamps ■ Thermobarb® barbed fittings ■Oetiker® ear type clamps ■Kwik Clamp™ nylon double bond hose clamps ■Worm gear clamps
CONTEF Without Wire
BENDRADIUS
(IN.)1/23/47/8
1-1/41-1/21-3/42.2302-3/4
34-1/4
79
AID
(IN.)1/45/163/81/25/83/41
1-1/41-1/2
234
BNOM.(IN.)3/4111
1-1/41-1/2
22-1/22-1/22-1/2
33
CNOM.(IN.).015.020.020.020.025.025.030.035.040.043.062.062
DREF.(IN.).320.414.450.590.660.780
1.1001.6001.9102.4503-3/44-3/4
FNOM.(IN.).185.277.308.431.493.617.862
1.1701.4501.9803.0004.000
MAXLENGTH
(FT.)1251251251007575504040403020
WORKINGPSI AT70°F625652403530272420171512
PART NO.
350 0070350 0147350 0224350 0301350 0378350 0455350 0532350 0609350 0686350 0763350 0917*350 0994*
BURSTPSI AT70°F2482202001601401201008065555040
*Limited stock availability; lead times and minimums may apply — call for details.� ‘E’ dimension to be specified at time of order. All lengths will be supplied with ‘B’ dimension cuffs.BOLD indicates the critical dimension for fittings application.
AID
(IN.)1/4 5/16 3/81/25/83/41
BNOM.(IN.)3/4111
1-1/41-1/2
2
CNOM.(IN.).015.020.020.020.025.025.030
DREF.(IN.).320.414.450.590.660.7801.100
FNOM.(IN.).185.277.308.431.493.617.862
BENDRADIUS
(IN.)1/23/47/8
1-1/41-1/21-3/42.230
MAXLENGTH
(FT.)12121220202020
WORKINGPSI AT70°F100877568625545
CONTEF With Wire
PART NO.
352 0076352 0153352 0230352 0307352 0384352 0461352 0538
BURSTPSI AT70°F400348300272248220180
� ‘E’ dimension to be specified at time of order. All lengths will be supplied with ‘B’ dimension cuffs.BOLD indicates the critical dimension for fittings application.
Made in U.S.A.
Custom Services■ Overbraid■ And More
Call for more information800-506-3924
■ Cut■ Size
E
BC
DF
(Cuff Length)
(Length Including Cuffs)
(Convolution OD)(Convolution ID)
(Wall)
�
(ID)A
8 www.newageindustries.com
123cStainless Steel Overbraided PTFE HoseSmooth Core PTFE Tub ing w i th S ta in less S tee l Overbra id ing
■ White PTFE inner core is made from non-toxic ingredients conformingto FDA standards
■ Black core is electrically conductive to release or eliminate static charge
■ Core material is inert; will not impart taste or odor orcontaminate the stream
■ Wide service temperature range (-65°F to 450°F)
■ Excellent weathering properties; non-flammable
■ Non-stick surface is easily cleaned by autoclaving, steam,or detergent
■ Series 300 stainless steel overbraid provides for high pressuresand protection of the core
■ Meets or exceeds SAE 100R14 specifications for size and pressure
NotesSmooth core STAINLESS STEEL
OVERBRAIDED PTFE HOSE is constructed ofextruded virgin PTFE material with a 300stainless steel wire braid reinforcementjacket. The core is inert and offers longflexural life, low permeability, non-flammability, and the lowest coefficient offriction of any solid material.
The overbraid permits higher pressureuses, reduces the possibility of kinking, andgenerally protects the core.
Black conductive core hose works well inapplications where static charge must bedissipated, such as those involving highresistivity fluids or gases at high velocity.
Flush cleaning of the hose to eliminatemanufacturing residue is recommendedprior to use.
Physical Properties**Temperature Range, °F -65 to 450Average Maximum Length, ft.
3/16” through 1/2”: 3005/8” and 3/4”: 1501” and 1-1/4”: 75
**Values listed are typical for the material used inmanufacture, except where noted, and are meant only asa guide to aid in design. Field testing should beperformed to find the actual values for your application.
NOM.HOSE
SIZE (IN.)
1/43/81/25/83/41
AVG.ID
(IN.)
.187
.312
.405
.500
.625
.875
BENDRADIUS
(IN.)
24
5.26.57.79
PARTNO.
900 0138900 0208900 0278900 0348900 0418900 0558
WORKINGPSI
AT 70°F
300025002000150012001000
BURSTPSI
AT 70°F
12000100008000600048004000
WHITE CORE – .030” inner core wall
DASH SIZE
-4-6-8
-10-12-16
AVG.OD(IN.)
.312
.445
.549
.648
.7781.030
BOLD indicates the critical dimension for fittings application.Consult factory for assembly information.
LBS.PER
FOOT
.077
.110
.124
.154
.170
.273
PARTNO.
901 0274901 0344901 0414901 0554
BLACK CONDUCTIVE CORE – .030” inner core wall
NOM.HOSE
SIZE (IN.)
1/25/83/41
AVG.ID
(IN.)
.405
.500
.625
.875
BENDRADIUS
(IN.)
5.26.57.79
WORKINGPSI
AT 70°F
2000150012001000
BURSTPSI
AT 70°F
8000600048004000
DASH SIZE
-8-10-12-16
AVG.OD(IN.)
.549
.648
.7781.030
LBS.PER
FOOT
.124
.154
.170
.273
BOLD indicates the critical dimension for fittings application.Consult factory for assembly information.
Custom Services■ Cut■ Size
■ Overbraid■ And More
Call for more information:800-506-3924
More NewAgeIndustries’ Owners
Khoeuth SomFabrication/Manu-facturing /Owner5 years
Brian KatchurProduct Develop-ment/Owner8 years
Kelly LiszewskiCustomer ServiceRep./Owner10 years
9www.newageindustries.com
123c
■ Made from chemically inert PFA fluoropolymer
■ No flow restrictions
■ Easy to disconnect and reuse
■ Excellent lock and seal ability
■ Precision molded to exacting tolerances
Pureloc®
P F A C o m p r e s s i o n F i t t i n g s
Notes
Made from virgin, high purity PFA fluoropolymer, PURELOC is ideal for ultra-pure fluid applications where contamination-free systems are used. Thisincludes semiconductor manufacturing,food and beverage processing, medical andbiomedical, laboratory, chromatographyequipment, and the chemical industries.
The gripper coupled with the precision-made ferrule provides excellent leak-proofconnections and prevents tubing blow-out.
The values above are typical for the material used in manufacture, except where noted, and are meant only asa guide to aid in design. Field testing should be performed to find the actual values for your application.
250
200
150
100
50
050 100 150 200 250 300 350
Fluid Temperature (°F)
Pre
ssu
re (
psi
G)
1/8”, 1/4”, & 3/8”1/2”3/4”
1. Cut tubing (A) cleanly at 90°.2. Push tubing through small end of nut (B), gripper (C), ferrule (D), and
seat the tubing end into the fitting body as far as it will go (E).3. Thread the nut onto the body and finger tighten. To complete the
installation, tighten the nut at least one additional turn.
Male Adapter
TUBE OD(IN.) x NPT
1/8 x 1/81/8 x 1/41/4 x 1/81/4 x 1/41/4 x 3/81/4 x 1/23/8 x 1/83/8 x 1/43/8 x 3/83/8 x 1/21/2 x 1/41/2 x 3/81/2 x 1/21/2 x 3/43/4 x 1/23/4 x 3/4
PARTNO.
532 0644532 0672532 0700532 0728532 0756532 0784532 0812532 0833532 0868532 0896532 0924532 0952532 0980532 1008532 1036532 1064
Female Adapter
TUBE OD(IN.) x FNPT
1/8 x 1/81/8 x 1/41/4 x 1/81/4 x 1/41/4 x 3/81/4 x 1/23/8 x 1/43/8 x 3/83/8 x 1/21/2 x 1/41/2 x 3/81/2 x 1/21/2 x 3/43/4 x 1/23/4 x 3/4
PARTNO.
532 0028532 0056532 0084532 0112532 0140532 0168532 0224532 0252532 0280532 0308532 0336532 0364532 0392532 0420532 0448
A↓
C D↓
E↓↓
B↓↓ ↓
Installation Instructions:
Male 90° Elbow
TUBE OD (IN.) x NPT
1/4 x 1/81/4 x 1/43/8 x 1/83/8 x 1/43/8 x 3/83/8 x 1/21/2 x 1/41/2 x 3/81/2 x 1/21/2 x 3/43/4 x 1/23/4 x 3/4
PARTNO.
532 3080532 3108532 3192532 3220532 3248532 3276532 3304532 3332532 3360532 3388532 3416532 3444
TUBE OD(IN.) x FNPT
1/8 x 1/81/4 x 1/43/8 x 1/43/8 x 3/83/8 x 1/21/2 x 1/41/2 x 1/2
PARTNO.
532 2604532 2660532 2688532 2716532 2744532 2772532 2828
Female 90° Elbow
continued on next page
10 www.newageindustries.com
123cPureloc®
P F A C o m p r e s s i o n F i t t i n g s
TUBEOD (IN.)
1/81/43/81/23/4
PARTNO.
532 6132532 6160532 6188532 6216532 6244
Union Tee
Reducing Union Connector
TUBE OD xTUBE OD (IN.)
1/8 x 1/41/4 x 3/81/4 x 1/23/8 x 1/21/2 x 3/4
PARTNO.
532 1764532 1820532 1848532 1876532 1904
Union Connector
TUBEOD (IN.)
1/81/43/81/23/4
PARTNO.
532 1484532 1512532 1540532 1568532 1596
PARTNO.
532 3948532 4004
Reducing 90° Elbow
TUBE OD(IN.) x NPT
1/4 x 1/81/4 x 1/43/8 x 1/83/8 x 1/43/8 x 3/83/8 x 1/21/2 x 1/41/2 x 3/81/2 x 1/23/4 x 3/4
PARTNO.
532 4697532 4732532 4760532 4788532 4816532 4844532 4872532 4900532 4928532 4956
Male Branch Tee
TUBE OD(IN.) x NPT
1/4 x 1/81/4 x 1/43/8 x 1/41/2 x 1/41/2 x 1/23/4 x 3/4
PARTNO.
532 5656532 5684532 5796532 5880532 5936532 5964
Male Run Tee
TUBEOD (IN.)
1/81/43/81/23/4
PARTNO.
532 3621532 3640532 3696532 3724532 3752
Union 90° Elbow
Bulkhead Union
TUBEOD (IN.)
1/81/43/81/23/4
PARTNO.
532 2072532 2100532 2128532 2156532 2184
TUBEOD (IN.)
1/81/43/81/23/4
PARTNO.
532 6860532 7056532 7252532 7448532 7644
Nut Replacement KitContains one nut, one gripper, and one ferrule
TUBE OD xTUBE OD (IN.)
1/4 x 3/83/8 x 1/2
11www.newageindustries.com
123c
Going beyond basic tubing, hose, and fittings has been an integral part ofNewAge Industries' business for many years. We possess the capabilities andexperience to create custom parts perfectly suited to your application. Post-extrusion fabrication and hose assembly opens another range of optionsfor providing parts to your exact specifications at a reasonable cost.
Discuss your application with someone fromour knowledgeable Sales Team today800-506-3924 or 215-526-2300
■ Custom Coiling
■ Custom Extrusions
■ Overbraiding & Jacketing
■ Hot Bond® - Thermal Bonding
■ Heat Formed Shapes
■ Fabrication Services - Cutting, Slitting, Printing, etc.
■ Hose Assemblies
■ Dip Molded Tubing
■ Molded Silicone Components
■ And More
Custom & Fabrication ServicesC r e a t e P a r t s C u s t o m i z e d t o M e e t Y o u r N e e d s
Meet Some of NewAge Industries’ OwnersThrough an Employee Stock Ownership Plan (ESOP), NewAge employeesare part owners in the company. Our jobs are part of an investment in ourfuture, and that’s reflected in our communications with customers andsuppliers, and with each other, now more than ever. When a customer calls,they can speak with an owner.
Annabelle BlackInside SalesManager/Owner23 years
Michael GillespieFabrication/Manu-facturing /Owner4 years
Dave SchofieldWarehouse Supv./Traffic Mgr./Owner5 years
Lorrie McGoughSales Order Clerk/Accounting/Owner8 years
Tom SlovikQuality ControlInspector/Owner1 year
Anthony SchmidtWarehouse/Owner1 year
DISTRIBUTOR PARTNER 800-50-NEWAGE(800-506-3924)
215-526-2300Fax: 800-837-1856
215-526-2190info@newageindustries.com
145 James WaySouthampton, PA 18966www.newageindustries.com
Coiltef, Contef, Corrtef, Hot Bond, Kwik Clamp, Pureloc, Thermobarb, NewAge, “Fluid Transfer Specialists,” The "N" Logo, and AdvantaPure are trademarks of NewAge® Industries, Inc. • Oetiker reg. TM Oetiker, Inc. • Hytrel trademark DuPont • Viton trademark DuPont Dow Elastomers
NOTICE: NewAge Industries, Inc. has been a privately owned corporation since 1954. Neither the corporation nor its principals are affiliated, in any way, with any other group or entity either representing themselves as or being referred to by the term New-Age.
WARRANTY: NewAge Industries’ products are warranted to be free from defects in material and workmanship. Any product found to carry such defects will be replaced without charge. This warranty is limited only to the replacement of NewAge Industries' products, item for item, which after examination byNewAge Industries are deemed defective. NewAge Industries specifically disclaims any other liability. The data supplied is provided as a helpful guideline and is believed to be reliable; however, nothing stated shall constitute a guarantee, recommendation, or warranty for any application.
1/13/10© NewAge Industries, Inc. 2010 Specifications are subject to change without notice.
More NewAge Industries Products
123c
Custom ServicesCut
SizeColorCoilOver-
braidHeat Form
Hot Bond®Assemblies
HardnessMore
Tubing & HosePVCPolyurethaneSiliconeFluoropolymerNylonPolyethylenePolypropyleneTPRViton®LatexHytrel®
High Purity Tubing & HoseSanitary tubing, hose, fittings,assemblies, and molded componentsfrom our AdvantaPure division meetthe needs of the pharmaceutical,biotech, food and beverage, dairy,cosmetics and fragrances, and chemicalindustries, as well as other sanitaryapplications. AdvantaPure products areavailable through a network of selectdistributors. www.advantapure.com
Fittings & Clamps for FluoropolymerPureloc® - PFA compression fittings. Stock sizes for 1/8”
to 3/4” O.D. in 13 styles. Made from chemically inert fluoropolymer.
Thermobarb® Plastic - Precision molded barbed fittings in nylon-6, high density polyethylene, PVDF,polypropylene, reinforced nylon, or reinforced poly-propylene. Sizes for 1/8” to 1” I.D. tubing in 15 styles.
Thermobarb® Brass - Durable brass barbed fittings.Sizes for 1/8” to 1” I.D. tubing in 10 styles.
Oetiker® Ear Type Clamps - Stainless steel or zinc-plated carbon steel clamps with a unique breathable design. 35 sizes from 5/32” to 1-9/16” in 3 styles.
Kwik Clamp™ - Nylon double-bond hose clamps.31 sizes from 1/4” to 4-1/4” nominal O.D.
Worm Gear Clamps - Stainless steel worm screw clamps. 28 sizes from 3/8” to 6” in 6 styles.
PTFE Thread SealantTubing & Hose Cutting Tools
Recommended