View
37
Download
0
Category
Preview:
Citation preview
Instruction manual
180720
ET100 V2 PNP ET115 3S PNP ET125 V2 PNP
NO RX FM800 RX2A PRO DSM2 AC900(S-FHSS+D16)
ET V2/3S Series
User manual and video please visit:WWW.LDARC.COM
Note: 2S configuration using 3S battery will cause damage to electronic equipmentET100 V2 ET115 3S ET125 V2
Only 2SInput Voltage
Wheelbase
Motor
Prop
Battery
100mm
XT1103-7800KV
1935
7.4V 450mAh 80C(JST)
78.6g
115mm
XT1104-5500KV
2345
11.1V 600mAh 50C(XT30)
96.4g
125mm
XT1104-7500KV
2840
7.4V 550mAh 80C(JST)
96.7g
Flytower 20*20(V2) F3+OSD FC+4in1 ESC 12A BLHeliS
VTX Q100 VTX(25mW/100mW 16CH)
Camera OV231(800TVL 150。
NTSC)
Receiver FM800,RX2A PRO,DSM2,AC900(S-FHSS+D16)
Name
2-3S Only 2SWeight
(not include battery&receiver)
ET100 V2 Configuration
Package List
PNP*11935 Prop*4Pairs(Color random)Suitcase*1 7.4V 450mAh 80C*1(JST)
ET Canopy×1
-1-
ET100 V2/115 3SRed Canopy×1 Paper Stickers*1
Wheelbase:100mm
Flytower 20*20(V2):
F3+OSD
4in1 12A BLheliS
VTX:Q100(25mW/100mW 16CH)
Camera:OV231(800TVL 150。
NTSC)
Motor:XT1103-7800KV
Prop:1935
Battery:7.4V 450mAh 80C(JST)
Voltage:7.4V
Weight:78.6g(not include battery and receiver)
Receiver:FM800,RX2A PRO,DSM2,
AC900(S-FHSS+D16)
ET100 V2
ET100 V2/115 3SClear Black Canopy×1
Package List
-2-
Wheelbase:115mm
Flytower 20*20(V2):
F3+OSD
4in1 12A BLheliS
VTX:Q100(25mW/100mW 16CH)
Camera:OV231(800TVL 150。
NTSC)
Motor:XT1104-5500KV
Prop:2345
Battery:11.1V 600mAh 50C(XT30)
Voltage:11.1V
Weight:96.4g(not include battery and receiver)
Receiver:FM800,RX2A PRO,DSM2,
AC900(S-FHSS+D16)
ET115 3S Configuration
PNP*1 11.1V 600mAh 50C*1(XT30)
ET115 3S
2345 Prop*4Pairs(Color random)Suitcase*1
ET Canopy×1 ET100 V2/115 3SRed Canopy×1 Paper Stickers*1ET100 V2/115 3S
Clear Black Canopy×1
Package List
-3-
Wheelbase:125mm
Flytower 20*20(V2):
F3+OSD
4in1 12A BLheliS
VTX:Q100(25mW/100mW 16CH)
Camera:OV231(800TVL 150。
NTSC)
Motor:XT1104-7500KV
Prop:2840
Battery:7.4V 550mAh 80C(JST)
Voltage:7.4V
Weight:96.7g(not include battery and receiver)
Receiver:FM800,RX2A PRO,DSM2,
AC900(S-FHSS+D16)
ET125 V2 Configuration
PNP*1 7.4V 550mAh 80C*1(JST)
ET125 V2
2840 Prop*4Pairs(Color random)Suitcase*1
ET Canopy×1 ET125 V2Red Canopy×1 Paper Stickers*1ET125 V2
Clear Black Canopy×1
VTX
ESC Motor
-4-
FC
M4(CW) M2(CCW)
M3(CCW)
Note:pay attention to the direction of rotation of the motor when installing the prop
M1(CW)+ -
M1
M2
M3
M4
BUZZER-GND
LED STRIP5V(BUZZER+)
4.0V VIN GND VIDEO
25mW
100mW
- +
-
+ VIN 2S-4S Lipo7V-18VGND
LED Frequency table
Click the key change frequency point
Please attention ventilation cooling
AntennaQ100-Mini 25mW/100mW 16CH VTX (2S-4S Lipo 7V-18V)
L=28mm,W=11mm,Weight=2.5g(Without camera and wire)
CAM
5VG
ND
VID
EOA
UD
IO
VCC
GN
DSIG
NA
LA
UD
IO
5VG
ND
S
VID
EO include O
SD
signal output
Connect these 3 pads to VTX when use 2layer tower(FC+ESC)
5
5V GN
D
G
RC IN3V
3
SPEK(DSMX)
GN
D
3.3V
SIN
SBUS PPMSIN5V
GN
D
BETAFLIGHT
USB
BIND:Power on the receiver while pressing the key,green LED fast blink meaning already in bind mode,user can release the key,then set your TX into bind mode.Green LED turn off and red LED solid mean bind finished,exit TX from bind mode,receiver’sgreen LED solid mean working normally.
FAILSAFE:Support 2 failsafe mode,press the key and hold 3s while receiver working normally can switch failsafe mode.Please make sure failsafe is working correctly before use the receiver!Failsafe mode 1: After 1s when lost transmitter signal,S.BUS keep output,throttle will 988us,all other channels will 1500us.Failsaft mode 2: After 1s when lost transmitter signal,S.BUS not output,user should setting related parameters to ensure flight controller handle failsafe.
Receiver BindAC900(S-FHSS+D16) bind,transmitter(FRSKY X9D/Futaba T18SZ)
RX2A PRO Bind(S.BUS),transmitter(FLYSKY FS-i6)
-5-
STATUS LED:LED of RX2A-PRO blink twice then solid when power on,the meaning as follow
First blink(air system) Second blink(failsafe mode) Then solid(signal status)
AFHDS2A air systemFailsafe mode 1
Failsafe mode 2
No signal
Signal received
Bind:Check receiver mode before bind,the first blink after power on indicate the setting, is S-FHSS, is D16FUTABA S-FHSS BIND:Turn on the TX then power on AC900 while pressing the key, green LED fast blink meaning already in bind mode, user can release the key. Bind procedure is completed and the receiver is working normally when green LED is solidFRSKY D16(NO Telemetry) BIND:Power on AC900 while pressing the key, green LED fast blink meaning already in bind mode, user can release the key, then set your TX into D16 bind mode. red LED solid meaning bind finished, exit TX from bind mode, receiver’s green LED solid meaning working normally
-6-
Connect
Firmware Update
OMNIBUS
3.1.7-OMNIBUS -10-04-2017 18:36(stable)
-7-
BETAFLIGHT firmware allready flash before leave the factory,user just need connect PC to adjust the parameter
1.Open betaflight configuration ,then click ,select FW version
2.Click ,then click to download FW to FC, click after FW
updating finish into setting menu
Product and Factory CodeName
ET100 V2 PNP NO RX
ET100 V2 PNP AC900
ET100 V2 PNP FM800
ET100 V2 PNP RX2A PRO
ET100 V2 PNP DSM2
ET100 V2 KIT
ET115 3S PNP NO RX
ET115 3S PNP AC900
ET115 3S PNP FM800
ET115 3S PNP RX2A PRO
ET115 3S PNP DSM2
ET115 3S KIT
ET125 V2 PNP NO RX
ET125 V2 PNP AC900
ET125 V2 PNP FM800
ET125 V2 PNP RX2A PRO
ET125 V2 PNP DSM2
ET125 V2 KIT
OV231
Q100 VTX
LED+Buzzer(ET V2/3S Part)
Air Cowling(Φ5 M2)
Factory Code
PNP.ET100 V2.NO RX
PNP.ET100 V2.AC900
PNP.ET100 V2.FM800
PNP.ET100 V2.RX2A PRO
PNP.ET100 V2.DSM2
KIT.ET100 V2
PNP.ET115 3S.NO RX
PNP.ET115 3S.AC900
PNP.ET115 3S.FM800
PNP.ET115 3S.RX2A PRO
PNP.ET115 3S.DSM2
KIT.ET115 3S
PNP.ET125 V2.NO RX
PNP.ET125 V2.AC900
PNP.ET125 V2.FM800
PNP.ET125 V2.RX2A PRO
PNP.ET125 V2.DSM2
KIT.ET125 V2
CAM.OV231
VTX.Q100
PART.LED+BUZZER(ET V2/3S PART)
PRRT.AIR COWLING(Φ5 M2)
Factory Code
PROP.1935.3.WHITE
PROP.2345.3.WHITE
PROP.2840.3.WHITE
BAT.7.4V 450MAH 80C
BAT.7.4V 550MAH 80C
BAT.11.1V 600MAH 50C
PART.BOTTOM PLATE.ET100
PART.BOTTOM PLATE.ET115
PART.BOTTOM PLATE.ET125
MOTOR.XT1103-7800KV
MOTOR.XT1104-7500KV
MOTOR.XT1104-5500KV
FLYTOWER.20*20(V2)
ESC.KK TOWER 12A
FC.F3+OSD(FLYTOWER 20*20 V2)
PART.KK TOWER SCREW(2 LAYER)
PART.KK TOWER WIRE
PART.ET100 V2/115 3S CANOPY
PART.ET125 V2 CANOPY
PART.1.9 PROTERTOR ALL.BLACK
PART.2.3 PROTERTOR ALL.BLACK
PART.2.8 PROTERTOR ALL.BLACK
Name
1935 Prop
2345 Prop
2840 Prop
Battery 7.4V 450mAh 80C
Battery 7.4V 550mAh 80C
Battery 11.1V 600mAh 50C
Carbon fiber plate(ET100 Part)
Carbon fiber plate(ET115 Part)
Carbon fiber plate(ET125 Part)
XT1103-7800KV
XT1104-7500KV
XT1104-5500KV
Flytower 20*20(V2)
4in1 ESC 12A(KK Tower Part)
F3+OSD FC(V2)
2 Layer Tower Screw(KK Tower Part)
Wire(KK Tower Part)
ET100 V2/115 3S Canopy
ET125 V2 Canopy
3.Calibration“Calibrate Accelerometer”
4.Selected UART3,then open“Serial RX”switch and saved
1.9 inch black propeller protector(all surround)2.3 inch black propeller protector(all surround)2.8 inch black propeller protector(all surround)
4058
36
4058
36
3035
-8-
6.PID setting
5.Configuration,select ESC protocol“DSHOT600”,Set up the receiver protocol,then open LED,OSD and DYNAMIC_FILTER
-9-
7.Default setting of receiver is 5th channel ARM(AUX1),6th channel mode switching(AUX2)
8.Setting 7th channel mode switching(AUX2).
9.Input“set small_angle = 180 ”,then set
FLIP OVER AFTER CRASH please upgrade the firmware to 3.2.1 version first,then set by BETAFLIGHT
-10-
After Sale Service
1.Provide free reparation service when find the product defect after purchase.
2.Provide pay-needed reparation service when product damage because improper operation.
3.China customers please contact with the after-sales service,overseas client please contact the dealer.
PNP/RTF Test report ID :
Flight test
Transmitter functions properly
Flying in good condition
Camera OK
VTX OK
QC:
Package check
PNP
RTF
Frame
Transmitter
ID is the same
All parts of the installation
Insulating sleeves have been installed manual
Complete accessories,total packages
QC:
Recommended