View
1
Download
0
Category
Preview:
Citation preview
1Public | ETAS K.K./EAS-Yh | 2018-06-05
© ETAS GmbH 2018. All rights reserved, also regarding any disposal, exploitation, reproduction, editing, distribution, as wel l as in the event of applications for industrial property rights.
EHANDBOOK-V5.1
クイックスタートガイド
2Public | ETAS K.K./EAS-Yh | 2018-06-05
© ETAS GmbH 2018. All rights reserved, also regarding any disposal, exploitation, reproduction, editing, distribution, as wel l as in the event of applications for industrial property rights.
1. はじめに
2. 作業の流れ
3. EHBファイルを選択
4. ドキュメント表示
5. 制御モデル表示
6. INCAの測定値をリアルタイム表示
7. INCAで測定したデータをOFFLINE表示
8. MDA8.2からの操作
9. インポート&エクスポート機能
10. サポート ホットライン
EHANDBOOK-V5.1 クイックスタートガイド
目次
目次
3Public | ETAS K.K./EAS-Yh | 2018-06-05
© ETAS GmbH 2018. All rights reserved, also regarding any disposal, exploitation, reproduction, editing, distribution, as wel l as in the event of applications for industrial property rights.
このクイックスタートガイドは、初心者の方を対象に、EHANDBOOK-NAVIGATOR
(以降、EHANDBOOK)の基本的な作業の流れを説明します。EHNDBOOKに関する
詳しい説明はマニュアルやオンラインヘルプを参照してください。
準備するもの
EHANDBOOKをインストールしたPC
※本資料は、V5.1をベースに説明します。
本資料では、下記2つのファイルを使用します。
・EHANDBOOK_V51_FlexECU_Demo.exp
・EHANDBOOK_V51_FlexECU_DEMO.ehb
・EHANDBOOK_V51_FlexECU_DEMO_ASCET.a2l
・EHANDBOOK_V51_FlexECU_DEMO_ASCET.hex
本資料では、下記2つのソフトを使用します。
・INCA
・MDA8.2
EHANDBOOK-V5.1 クイックスタートガイド
1. はじめに
4Public | ETAS K.K./EAS-Yh | 2018-06-05
© ETAS GmbH 2018. All rights reserved, also regarding any disposal, exploitation, reproduction, editing, distribution, as wel l as in the event of applications for industrial property rights.
EHANDBOOK-V5.1 クイックスタートガイド
2. 作業の流れ
EHBファイルを選択
制御モデル表示
MDA8.2からの操作
インポート&エクスポート
機能
INCAで測定し
たデータをOFFLINE表示
EHANDBOOKの起動を行い、EHBファイルを選択します。
INCAで測定している値をEHANDBOOKの制御モデル上にリアルタイムで表示させます。
INCAで測定したデータ(.dat, .mf3, .mf4) )の値をEHANDBOOKの制御モデル上に表示させます。
MDA8.2からEHANDBOOKのデータ表示時間を操作します。
エクスポートしたファイルをインポートします。
INCAの測定値をリアルタ
イム表示
参照する制御モデルを表示します。
ドキュメント表示 検索、コメント入力、ブックマーク設定を行います。
5Public | ETAS K.K./EAS-Yh | 2018-06-05
© ETAS GmbH 2018. All rights reserved, also regarding any disposal, exploitation, reproduction, editing, distribution, as wel l as in the event of applications for industrial property rights.
「起動を行い、EHBファイルを選択」する方法
1) EHANDBOOKを起動します。
2) 「File→Open」を選択します。
3) EHBファイルを選択します。
「EHBファイルを指定し起動」する方法
1)WindowsExplorerのEHBファイルをダブルクリックします。
※ダブルクリックにより、EHANDBOOKが起動されます。
EHANDBOOK-V5.1 クイックスタートガイド
3. EHBファイルを選択
EHANDBOOKの起動は、「起動を行い、EHBファイルを選択」する方法と、「EHBファイルを指定し、起動」する方法の2種類があります。下記にそれぞれの方法を説明します。
※ここでは、「EHANDBOOK_V51_FlexECU_DEMO.ehb」ファイルを選択します。
3.1 EHBファイルを選択
6Public | ETAS K.K./EAS-Yh | 2018-06-05
© ETAS GmbH 2018. All rights reserved, also regarding any disposal, exploitation, reproduction, editing, distribution, as wel l as in the event of applications for industrial property rights.
1)検索フィールドで入力して検索します。下図のように候補も表示されます。
2)「Search」ボタンを押下することで下図のように検索結果が表示されます。
4.1 ドキュメント表示(検索機能)提案検索/コンテナ内一括検索機能を説明します。
EHANDBOOK-V5.1 クイックスタートガイド
4. ドキュメント表示
7Public | ETAS K.K./EAS-Yh | 2018-06-05
© ETAS GmbH 2018. All rights reserved, also regarding any disposal, exploitation, reproduction, editing, distribution, as wel l as in the event of applications for industrial property rights.
4.2 ドキュメント表示(コメント機能)
EHANDBOOK-V5.1 クイックスタートガイド
4. ドキュメント表示
1)ドキュメントの仕様書には をクリックすると文字を入力するコメント
欄が表示されます。
2)コメントを入力します。
コメント機能を説明します。
コメント入力
8Public | ETAS K.K./EAS-Yh | 2018-06-05
© ETAS GmbH 2018. All rights reserved, also regarding any disposal, exploitation, reproduction, editing, distribution, as wel l as in the event of applications for industrial property rights.
4.2 ドキュメント表示(ブックマーク機能)
EHANDBOOK-V5.1 クイックスタートガイド
4. ドキュメント表示
1)ブックマークに登録したい箇所にカーソルを合わせ右クリッ
クを行い、「CREATE BOOKMRK」を選択することで、
ブックマークを作成することができます。
2)ブックマーク作成の際には、「名前」と「説明文」を記述可能
です。
3)ブックマークタブを選択すると、作成したブックが表示され、参照したいブックマークをクリックすると、ブックマークされたページの内容が表示されます。
ブックマーク機能を説明します。
9Public | ETAS K.K./EAS-Yh | 2018-06-05
© ETAS GmbH 2018. All rights reserved, also regarding any disposal, exploitation, reproduction, editing, distribution, as wel l as in the event of applications for industrial property rights.
1)起動画面から を押下して、3つの項目からモデルの種類を選択
します。下図の赤枠参照。 ※デフォルトはASCET Modelsとなります。
2)ツリー内にある「Lcc-Lambda Correction Calculation」を選択し、
中身を開きます。「Function Overview」をダブルクリックすると
全体図が開きます。
3)信号の入出力関係を追うには、入出力に対応しているをクリックします。
5.1 制御モデル表示参照する制御モデルを表示します。
EHANDBOOK-V5.1 クイックスタートガイド
5. 制御モデル表示
10Public | ETAS K.K./EAS-Yh | 2018-06-05
© ETAS GmbH 2018. All rights reserved, also regarding any disposal, exploitation, reproduction, editing, distribution, as wel l as in the event of applications for industrial property rights.
4)モデル部分をダブルクリックするとモデルにジャンプします。
5)さらにモデルをクリックすると制御モデルが表示されます。
6)下記のように、制御モデルが表示されます。
5.1 制御モデル表示参照する制御モデルを表示します。
EHANDBOOK-V5.1 クイックスタートガイド
5. 制御モデル表示
クリック
クリック
11Public | ETAS K.K./EAS-Yh | 2018-06-05
© ETAS GmbH 2018. All rights reserved, also regarding any disposal, exploitation, reproduction, editing, distribution, as wel l as in the event of applications for industrial property rights.
1)変数にカーソルを合わせ右クリックで表示される「Output」などを
選択して出力のフローをハイライト表示して追うことができます。
2)変数にカーソルを合わせ右クリックで表示される「Intput」などを
選択して入力のフローをハイライト表示して追うことができます。
5.2 ハイライト表示機能モデル内信号フローをハイライト表示させます。
EHANDBOOK-V5.1 クイックスタートガイド
5. 制御モデル表示
12Public | ETAS K.K./EAS-Yh | 2018-06-05
© ETAS GmbH 2018. All rights reserved, also regarding any disposal, exploitation, reproduction, editing, distribution, as wel l as in the event of applications for industrial property rights.
下記のように、バスモデルのinput部分のハイライト表示を行うと、バスの有効となる部分のみハイライト表示されます。
「EHANDBOOK_V51_FlexECU_DEMO.ehb」には、下記の処理は含まれていないため、本機能は、説明のみになります。
バスモデルのハイライト表示に関しては、有効となるバスのみがハイライト表示されます。
EHANDBOOK-V5.1 クイックスタートガイド
5. 制御モデル表示
EHANDBOOK-V5.1新機能5.2 ハイライト表示機能
13Public | ETAS K.K./EAS-Yh | 2018-06-05
© ETAS GmbH 2018. All rights reserved, also regarding any disposal, exploitation, reproduction, editing, distribution, as wel l as in the event of applications for industrial property rights.
-INCAの操作になります。
1) INCAを起動し、データベースアイテムより右クリックを行い、
インポートを選択します。
2)インポート画面よりファイル選択ボタンを押下します。
3)インポートするファイル「EHANDBOOK_V51_FlexECU_Demo.exp」を選択します。
6.1 INCAの測定値をリアルタイム表示INCAで測定している値をEHANDBOOKの制御モデル上にリアルタイムで表示させます。
EHANDBOOK-V5.1 クイックスタートガイド
6. INCAの測定値をリアルタイム表示
14Public | ETAS K.K./EAS-Yh | 2018-06-05
© ETAS GmbH 2018. All rights reserved, also regarding any disposal, exploitation, reproduction, editing, distribution, as wel l as in the event of applications for industrial property rights.
4) 「デバイス→ハードウェアの設定」を選択します。
5) ハードウェア初期化ボタンを押下します。
6) 「実験→実験開始」を選択します
7) 実験画面が起動されるため、表示した状態にします。
6.1 INCAの測定値をリアルタイム表示INCAで測定している値をEHANDBOOKの制御モデル上にリアルタイムで表示させます。
EHANDBOOK-V5.1 クイックスタートガイド
6. INCAの測定値をリアルタイム表示
15Public | ETAS K.K./EAS-Yh | 2018-06-05
© ETAS GmbH 2018. All rights reserved, also regarding any disposal, exploitation, reproduction, editing, distribution, as wel l as in the event of applications for industrial property rights.
− EHANDBOOKの操作になります。
1)INCAの実験環境を起動している状態で、右下の
Data Sourceより「INCA Experiment (Live)」を選択します。
2)下記のようなダイアログが表示されますので、Connect
ボタンを押下します。
※ボタンがチェックされていない場合は、INCAの状態
(ハードウェアの初期化)などを確認してください。
3)関連するすべての変数をINCAに表示したい場合は右下の「Display all Values」ボタンを押下します。
4)ボタンを押下すると、INCAに自動的に変数が設定されます。
6.1 INCAの測定値をリアルタイム表示INCAで測定している値をEHANDBOOKの制御モデル上にリアルタイムで表示させます。
EHANDBOOK-V5.1 クイックスタートガイド
6. INCAの測定値をリアルタイム表示
16Public | ETAS K.K./EAS-Yh | 2018-06-05
© ETAS GmbH 2018. All rights reserved, also regarding any disposal, exploitation, reproduction, editing, distribution, as wel l as in the event of applications for industrial property rights.
− EHANDBOOKの操作になります。
5)リアルタイム表示(計測開始)をしたい場合は、右下の「Start Visulization」ボタンを押下します。
6)下記のように測定値がリアルタイムで表示されます。
6.1 INCAの測定値をリアルタイム表示INCAで測定している値をEHANDBOOKの制御モデル上にリアルタイムで表示させます。
EHANDBOOK-V5.1 クイックスタートガイド
6. INCAの測定値をリアルタイム表示
17Public | ETAS K.K./EAS-Yh | 2018-06-05
© ETAS GmbH 2018. All rights reserved, also regarding any disposal, exploitation, reproduction, editing, distribution, as wel l as in the event of applications for industrial property rights.
7)「Stop Measurement」を押下で停止します。
※INCA上での停止はできませんが、WPに切替えて適合作業は可能です。モデル上の値も変わります。
6.1 INCAの測定値をリアルタイム表示INCAで測定している値をEHANDBOOKの制御モデル上にリアルタイムで表示させます。
EHANDBOOK-V5.1 クイックスタートガイド
6. INCAの測定値をリアルタイム表示
18Public | ETAS K.K./EAS-Yh | 2018-06-05
© ETAS GmbH 2018. All rights reserved, also regarding any disposal, exploitation, reproduction, editing, distribution, as wel l as in the event of applications for industrial property rights.
-INCAの操作になります。
1) 実験画面の「記録」ボタンを押下します。 3)記録するファイル名を指定します。
7.1 INCAで測定したデータをOFFLINE表示INCAで測定したデータ(.dat, .mf3, .mf4) )の値をEHANDBOOKの制御モデル上に表示させます。
2) 実験画面の「停止」ボタンを押下します。
EHANDBOOK-V5.1 クイックスタートガイド
7. INCAで測定したデータをOFFLINE表示
19Public | ETAS K.K./EAS-Yh | 2018-06-05
© ETAS GmbH 2018. All rights reserved, also regarding any disposal, exploitation, reproduction, editing, distribution, as wel l as in the event of applications for industrial property rights.
− EHANDBOOKの操作になります。
1)INCAの実験環境を起動している状態で、右下の
Data Sourceより「Mesurement and Calibration Files」
を選択します。
2)下記のようなダイアログが表示されますので、先ほど
測定した「Mesurement File」を選択します。
7.1 INCAで測定したデータをOFFLINE表示INCAで測定したデータ(.dat, .mf3, .mf4) )の値をEHANDBOOKの制御モデル上に表示させます。
EHANDBOOK-V5.1 クイックスタートガイド
7. INCAで測定したデータをOFFLINE表示
3)関連するすべての変数をINCAに表示したい場合は右下の「Display all Values」ボタンを押下します。
4)ボタンを押下すると、INCAに変数が設定されます。
20Public | ETAS K.K./EAS-Yh | 2018-06-05
© ETAS GmbH 2018. All rights reserved, also regarding any disposal, exploitation, reproduction, editing, distribution, as wel l as in the event of applications for industrial property rights.
5)モデル表示の下部分で、 ボタンの操や、
へ時間入力を行う事により
INCAで想定したデータがオフラインで表示
されます。
INCAで測定したデータ(.dat, .mf3, .mf4) )の値をEHANDBOOKの制御モデル上に表示させます。
EHANDBOOK-V5.1 クイックスタートガイド
7. INCAで測定したデータをOFFLINE表示
7.1 INCAで測定したデータをOFFLINE表示
21Public | ETAS K.K./EAS-Yh | 2018-06-05
© ETAS GmbH 2018. All rights reserved, also regarding any disposal, exploitation, reproduction, editing, distribution, as wel l as in the event of applications for industrial property rights.
− EHANDBOOKの操作になります。
1)INCAの実験環境を起動している状態で、右下の
Data Sourceより「Mesurement and Calibration Files」
を選択します。
2)下記のようなダイアログが表示されますので、A2Lファイルと、
HEXファイルを選択します。
EHANDBOOK-V5.1 クイックスタートガイド
7. INCAで測定したデータをOFFLINE表示
3)適合変数名をクリックすると変数データが表示されます。
4)下記のように、変数データが設定されます。
7.2 A2LとHEXの適合値を表示A2LとHEXに記述されている適合値をEHANDBOOKの制御モデル上に表示させます。
EHANDBOOK-V5.1新機能
22Public | ETAS K.K./EAS-Yh | 2018-06-05
© ETAS GmbH 2018. All rights reserved, also regarding any disposal, exploitation, reproduction, editing, distribution, as wel l as in the event of applications for industrial property rights.
5)変数のMoreをクリックすると、詳細データが表示され、Defeine FunctionFmcをクリックすると、
デファイン表示(ソースコード等)が表示されます
EHANDBOOK-V5.1 クイックスタートガイド
7. INCAで測定したデータをOFFLINE表示
7.2 A2LとHEXの適合値を表示A2LとHEXに記述されている適合値をEHANDBOOKの制御モデル上に表示させます。
EHANDBOOK-V5.1新機能
23Public | ETAS K.K./EAS-Yh | 2018-06-05
© ETAS GmbH 2018. All rights reserved, also regarding any disposal, exploitation, reproduction, editing, distribution, as wel l as in the event of applications for industrial property rights.
3)INCAで測定したXDA(.xda)ファイルを選択します。
INCAで測定したデータ(.dat, .mf3, .mf4) )の値をMDA8.2から操作し、EHANDBOOKの制御モデル上に表示させます。
EHANDBOOK-V5.1 クイックスタートガイド
8. MDA8.2からの操作
8.1 MDA8.2からの操作
− MDA8.2からの操作になります。
※本操作は、MDA8.2がインストールされている必要があります。
※ EHANDBOOKを、終了した状態で行ってください。
1)MDA8.2を立ち上げ、新規作成ボタンを押下します。
2)XDAのインポートボタンを押下します。
EHANDBOOK-V5.1新機能
24Public | ETAS K.K./EAS-Yh | 2018-06-05
© ETAS GmbH 2018. All rights reserved, also regarding any disposal, exploitation, reproduction, editing, distribution, as wel l as in the event of applications for industrial property rights.
INCAで測定したデータ(.dat, .mf3, .mf4) )の値をMDA8.2から操作し、EHANDBOOKの制御モデル上に表示させます。
EHANDBOOK-V5.1 クイックスタートガイド
8. MDA8.2からの操作
8.1 MDA8.2からの操作
4)オシロスコープボタンをレイヤへドラッグ&ドロップします。
5)参照したい変数をドラッグ&ドロップします。
6)カーソルを追加します。
7)追加したカーソルを参照したい位置(時間)へ移動します。
EHANDBOOK-V5.1新機能
25Public | ETAS K.K./EAS-Yh | 2018-06-05
© ETAS GmbH 2018. All rights reserved, also regarding any disposal, exploitation, reproduction, editing, distribution, as wel l as in the event of applications for industrial property rights.
INCAで測定したデータ(.dat, .mf3, .mf4) )の値をMDA8.2から操作し、EHANDBOOKの制御モデル上に表示させます。
EHANDBOOK-V5.1 クイックスタートガイド
8. MDA8.2からの操作
8.1 MDA8.2からの操作
8)右上の「EHANDBOOKコネクト」ボタンを押下します。
9)下記ダイアログが表示されるため、EHBファイルを選択
し、コネクトボタンを押下します。
10) 下記のダイアログが表示されるため、A2L/HEX
/Mesurementファイル等の設定し、Loadボタンを
押下します。
11)「Display All Value」ボタンを押下し、測定結果表示可能
状態にします。
EHANDBOOK-V5.1新機能
26Public | ETAS K.K./EAS-Yh | 2018-06-05
© ETAS GmbH 2018. All rights reserved, also regarding any disposal, exploitation, reproduction, editing, distribution, as wel l as in the event of applications for industrial property rights.
INCAで測定したデータ(.dat, .mf3, .mf4) )の値をMDA8.2から操作し、EHANDBOOKの制御モデル上に表示させます。
EHANDBOOK-V5.1 クイックスタートガイド
8. MDA8.2からの操作
8.1 MDA8.2からの操作
12)カーソルを右クリックし、EHANDBOOK時間設定送信
ボタンを押すと、EHANDBOOKの送信時間が変更
されます。
EHANDBOOK-V5.1新機能
27Public | ETAS K.K./EAS-Yh | 2018-06-05
© ETAS GmbH 2018. All rights reserved, also regarding any disposal, exploitation, reproduction, editing, distribution, as wel l as in the event of applications for industrial property rights.
1)メニューの「File」からエクスポートファイルを作成できます。
9.1 インポート&エクスポート機能エクスポート&インポート機能を使用して、他のPCに情報を反映したり、共有することができます。
EHANDBOOK-V5.1 クイックスタートガイド
9. インポート&エクスポート機能
2)メニューの「File」からエクスポートファイルをインポートすることができます。
エクスポートファイル
エクスポート インポート
28Public | ETAS K.K./EAS-Yh | 2018-06-05
© ETAS GmbH 2018. All rights reserved, also regarding any disposal, exploitation, reproduction, editing, distribution, as well as in the even t of applications for industrial property rights.
EHANDBOOK-V5.1 クイックスタートガイド
10. サポート ホットライン
お問い合わせ先
製品に関するご質問や技術サポート等は、各地域のETAS 支社までお問い合わせください。
日本支社
製品に関するご質問
Phone: (045) 222-0900
E-mail: sales.jp@etas.com
技術サポート
Phone: (045) 222-0950
E-mail: inca.hotline.jp@etas.com
その他支社
各国支社につきましては、ETAS ホームページをご覧ください。
Germany WWW: http://www.etas.com/
各国支社 WWW: http://www.etas.com/ja/contact.php
技術サポートWWW: http://www.etas.com/ja/hotlines.php
Recommended