View
7
Download
0
Category
Preview:
Citation preview
Auckland Tel: 09-525 1753Fax: 09-525 1756
Email: sales@carrel-electrade.co.nzWeb: www.carrel-electrade.co.nz
Christchurch Tel: 03-366 1242Fax: 03-379 1991
CARREL-ELECTRADE LTDnot just products... solutions!
C A R R E L - E L E C T R A D E L I M I T E D
New Zealand Owned and Operated
0014
DIN Integra 1630 Series Digital Metering System
Multifunction Integra 1630 digital metering systems provide high accuracy 0.2% measurement, display and communication of all major electrical and power quality parameters including total harmonic distortion (THD)measurement up to the 31st harmonic. To suit user requirements, the rangeincludes single-phase, three-phase three-wire and triple-phase four-wirecapability, all selectable at the point of installation.
This DIN 96 panel mounted enclosure offers simple programming and display of up to 35 electrical measurement parameters via a simple menu-driven userinterface on the front panel. Integra 1630 digital metering system benefits from optional pulsed and digital communication outputs. This allows enhanced status information of up to 60 measured parameters to becommunicated to SCADA, building management or other systems. Additionally,a simple Windows-based software package is available to remotely configure the Integra and display all 60 major electrical and power quality parameters.
FeaturesLow profile
High contrast LED display
0.2% accuracy
LED annunciators for each measuredparameter
ProfibusTM
User programmable system configuration(4-wire default)
Fully programmable VT and CT ratios
Current demand per phase
Elapsed time counter for connected loads
Optional bezel for very low profileapplications
• ProfibusTM
NOWNOWwith Profibus DP
Communications Option
ENERGY DIVISION
Product Codes
I N T – X X X X – X - X – X - X X X
Product System Type Input Input Auxiliary OptionsFamily V I V
16 30–LED DIN96 L - 57.7 - 139 L - N 5 – 5A L – 12 - 48 V DC 000 - No Option
(100 - 240 L - L) 1 – 1A M - 100 – 250V 010 - Modbus
Low User M - 140 - 277 L - N AC/DC 100 - One PulseProfile Selectable System (241 - 480 L - L) 110 - One Pulse
Type One Modbus
Features as Factory Default 200 - Two PulseSpecified - 4 Wire 210 - Two Pulse
One Modbus
050 - ProfibusTM
250 + Two pulse ProfibusTM
CT Accessories
Crompton Instruments also offer a complete range of high qualitycurrent transformers offering comprehensive measuring and protectionclass accuracies. The range offers a wide selection of system currentratings, busbar sizes, case widths, apertures and mounting options toevery application.
FeaturesCost effective moulded case measuring current transformers
Limited range include the seven most popular sizes of current transformers
Ratio ratings from 30/5 to 4000/5
Comprehensive measurement of class accuracy
Wide range of system current ratings, busbar sizes, case widths and apertures
Wire sealable terminal covers
Feet mounting and busbar options
Order Code ExampleINT-1630-M-5-M-250Integra 1630 digital metering system, 3-phase 4-wire, nominal input voltage, 140-277V L-N (241-480V) L-L, 5A CTinput, auxiliary supply 100 to 250V AC or DC, two relay pulsed output and one Profibus communication port.
Tyco Electronics UK Limited, Crompton InstrumentsFreebournes Road, Witham, Essex, CM8 3AH, UKPhone: ++44 (0) 870 870 7500 Fax: ++44 (0) 870 240 5289www.crompton-instruments.com
a vital part of your world
© Tyco Electronics CI-EPP-Integra1630-03/07
All of the above information, including drawings, illustrations and graphic design, reflects our present understanding and is to thebest of our knowledge and belief correct and reliable. Users, however, should independently evaluate the suitability of each productfor the desired application. Under no circumstances, does this constitute an assurance of any particular quality or performance. Suchan assurance is only provided in the context of our product specifications or explicit contractual arrangements. Our liability for theseproducts is set forth in our standard terms and conditions of sale. Tyco is a trademark. CROMPTON is a trademark of CromptonParkinson Ltd. and is used by Tyco Electronics under licence. Profibus is a trademark of PROFIBUS Nutzerorganisation e.v
Energy Division –economical solutions for the electrical power industry: cable accessories,connectors & fittings, electrical equipment, instruments, lighting controls, insulators &insulation enhancement and surge arresters.
Auckland Tel: 09-525 1753Fax: 09-525 1756
Email: sales@carrel-electrade.co.nzWeb: www.carrel-electrade.co.nz
Christchurch Tel: 03-366 1242Fax: 03-379 1991
CARREL-ELECTRADE LTDnot just products... solutions!
C A R R E L - E L E C T R A D E L I M I T E D
New Zealand Owned and Operated
0014
A range of 3-in-1 current transformers combine threetraditional current transformers in one moulded case. 3-in-1 current transformers can be directly installed next to a three-phase moulded case circuit breaker, thus savinginstallation time where fitting three standard individualcurrent transformers would be required. The M3N1 range of current transformers offers primary currents between60-630A with 5A secondaries with up to class 0.5 accuracy performance.
3-in-1 Current Transformers
Features• Cost effective three-phase
moulded case
• Ratio's ranging from 60/5 to 630/5
• Integrated wire sealableterminal cover
• Busbar, DIN-rail and metal feetmounting hardware supplied
• Combined M4 posi/slot screw
Benefits• Isolated output for safety• Faster installation• Compact size• Ex-stock delivery
Applications• Switchgear• Distribution systems• Generator sets• Control panels
Energy Division
Specifications
System voltage 720V maximum
Test voltage 3kV for 1 minute
System frequency 50Hz or 60Hz
Primary ratings 60A to 630A
Short circuit thermal current 60 x rated primary current (lth): for 1 sec
Overload withstand 1.2 x rated current continuously
Rated dynamic current = 2.55 x lht
Secondary terminals M4 screw terminals
Enclosure Flame retardant grade classified UL 94V-O
Aperture holes centres 25, 35, 45mm
Operating temperature -20°C to +85°C
Accuracy Class 0.5, 1, 3Mounting hardware Plug-in metal feet for wall or base mounting Busbar and DIN-rail mounting
Compliant with IEC/EN 60044-1
Recommended