View
10
Download
0
Category
Preview:
Citation preview
0
.504.00
0
15
20
15
2530
amidia diamond knivesmade in Switzerland
Diamond cutting instruments for micro surgery
Amidia LTD has been manufacturing diamond knives for ophthalmology, micro surgery and plastic surgery for the last 20 years. Our many years of experience and strict quality controls allow us to only manufacture and sell first-class products.
Apart from our range of monocrystalline diamond blades, today we also offer blades made out of CVD diamonds. These blades are an interesting alternative to single use disposable blades since they can be used 400 – 500 times. A damaged blade can be replaced cheaply.
In the area of ophthalmology, we offer all commonly used designs. Thus we can provide a wide range of LRI and MICS blades. Our project managers are very happy to provide you with blades according to your customer-specific requirements with new blade dimensions.
We are very pleased to be able to offer you our products and services.
About Amidia LTD
Version 06 - September 12 2017
Amidia LTD Mattenstrasse 11 CH-2555 Brügg
Phone +41 32 333 24 74 Fax +41 32 333 24 76
Mail info@amidia.ch Web www.amidia.ch 3
Diamond cutting instruments for micro surgery
Contents
Diamond knives for cataract surgery (titanium handles with a pressure mechanism) 4
Diamond knives for cataract surgery (titanium bajonet handle with the j-slot mechanism) 7
3D diamond knives 10
Diamond knives for glaucoma surgery 11
Diamond knives for LRI surgery 12
Diamond knives with a micrometer for refractive surgery 14
Instructions for diamond knives with a micrometer 16
Diamond knives to implant Intacs and Kera Rings 17
Diamond knives for retinal surgery 17
Step diamond knives 18
Black diamond knives 20
Diamond knives for micro surgery 22
Zeppelin diamond knives for micro surgery 24
Cosmetic diamond knives for plastic surgery 26
Accessories 27
Directions for use 28
Why diamonds are better than disposable blades 30
Customer service 31
4
Amidia LTD Mattenstrasse 11 CH-2555 Brügg
Phone +41 32 333 24 74 Fax +41 32 333 24 76
Mail info@amidia.ch Web www.amidia.ch
B = width / L = length / D = thickness / A = angle
Diamond cutting instruments for micro surgery
Diamond knives for cataract surgery (titanium handles with a pressure mechanism)
The Amidia pencil handle is made out of best quality titanium material.Each diamond blade goes with a straight blade holder or a 30 degree angled holder.
drawingangled holder
straight holder description B L D A/A1 blade
straight / single edge
DIAMON D CUTTI NG I N STR U M E NTS FOR M ICROS U RG E RY
Amidia AG Telefon | Fax InternetMattenstrasse 11 +41 32 333 24 74 info@amidia.chCH-2555 Brügg +41 32 333 24 76 www.amidia.chSwitzerland
08 |
08
Page 6
TITAN Pencil Handle No. 200
B D
A
0.171.0
30°
0.171.0
3F
0.17width
60°
0.171.0
40°
45° 30°
• The amidia pencil handle is made out of best quality TITAN and MEDICAL STEEL material.• Available with all diamond blades you will find in our leaflets, for pencil handle.• Each diamond blade goes with a straight blade holder, or 30 degree angled holder
(A in the Article No. means 30 degree angled)
STANDARD BLADES
Diamond Knife Diamond BladeNo. 211 / straight No. 11No. 211A / straight, angled No. 11
STANDARD BLADES
Diamond Knife Diamond BladeNo. 212 / straight No. 12No. 212A / straight, angled No. 12
STANDARD BLADES
Diamond Knife Diamond BladeNo. 213 / tri-facet No. 13No. 213A / tri-facet, angled No. 13
0.171.0
45°
0.171.0
30°
3F
0.17width
60°
0.171.0
40°
45° 30°
0.171.0
45°
0.171.0
30°
B D
0.17width
60°
0.171.0
40°
AA1
STANDARD BLADES
Diamond Knife Diamond BladeNo. 271 / lance with blunt sides No. 71No. 271A / lance with blunt sides, angled No. 71
0.171.0
45°
0.171.0
30°
0.171.0
3F
0.17width
60°
45° 30°
A
B D
L
L
L
216A 216 straight 0.7 2.0 0.17 30° 16
287A 287 straight 1.0 2.0 0.17 30° 87
212A 212 straight 1.0 3.0 0.17 30° 12
264SA 264S straight 1.5 4.0 0.17 30° 64S
215A 215 straight 0.7 2.0 0.17 45° 15
211A 211 straight 1.0 3.0 0.17 45° 11
210A 210 straight 1.5 3.0 0.17 45° 10
211SA 211S straight 2.0 3.0 0.17 45° 11S
tri-facet
DIAMON D CUTTI NG I N STR U M E NTS FOR M ICROS U RG E RY
Amidia AG Telefon | Fax InternetMattenstrasse 11 +41 32 333 24 74 info@amidia.chCH-2555 Brügg +41 32 333 24 76 www.amidia.chSwitzerland
08 |
08
Page 6
TITAN Pencil Handle No. 200
B D
A
0.171.0
30°
0.171.0
3F
0.17width
60°
0.171.0
40°
45° 30°
• The amidia pencil handle is made out of best quality TITAN and MEDICAL STEEL material.• Available with all diamond blades you will find in our leaflets, for pencil handle.• Each diamond blade goes with a straight blade holder, or 30 degree angled holder
(A in the Article No. means 30 degree angled)
STANDARD BLADES
Diamond Knife Diamond BladeNo. 211 / straight No. 11No. 211A / straight, angled No. 11
STANDARD BLADES
Diamond Knife Diamond BladeNo. 212 / straight No. 12No. 212A / straight, angled No. 12
STANDARD BLADES
Diamond Knife Diamond BladeNo. 213 / tri-facet No. 13No. 213A / tri-facet, angled No. 13
0.171.0
45°
0.171.0
30°
3F
0.17width
60°
0.171.0
40°
45° 30°
0.171.0
45°
0.171.0
30°
B D
0.17width
60°
0.171.0
40°
AA1
STANDARD BLADES
Diamond Knife Diamond BladeNo. 271 / lance with blunt sides No. 71No. 271A / lance with blunt sides, angled No. 71
0.171.0
45°
0.171.0
30°
0.171.0
3F
0.17width
60°
45° 30°
A
B D
L
L
L
217A 217 tri-facet 0.7 2.0 0.17 45°/30° 17
213A 213 tri-facet 1.0 3.0 0.17 45°/30° 13
curved
D
L
B
4F
224A 224 curved 4 facets 1.0 3.0 0.17 24
Amidia LTD Mattenstrasse 11 CH-2555 Brügg
Phone +41 32 333 24 74 Fax +41 32 333 24 76
Mail info@amidia.ch Web www.amidia.ch 5
B = width / L = length / D = thickness / A = angle
Diamond cutting instruments for micro surgery
drawingangled holder
straight holder description B L D A/A1 blade
lance
DIAMON D CUTTI NG I N STR U M E NTS FOR M ICROS U RG E RY
Amidia AG Telefon | Fax InternetMattenstrasse 11 +41 32 333 24 74 info@amidia.chCH-2555 Brügg +41 32 333 24 76 www.amidia.chSwitzerland
08 |
08
Page 6
TITAN Pencil Handle No. 200
B D
A
0.171.0
30°
0.171.0
3F
0.17width
60°
0.171.0
40°
45° 30°
• The amidia pencil handle is made out of best quality TITAN and MEDICAL STEEL material.• Available with all diamond blades you will find in our leaflets, for pencil handle.• Each diamond blade goes with a straight blade holder, or 30 degree angled holder
(A in the Article No. means 30 degree angled)
STANDARD BLADES
Diamond Knife Diamond BladeNo. 211 / straight No. 11No. 211A / straight, angled No. 11
STANDARD BLADES
Diamond Knife Diamond BladeNo. 212 / straight No. 12No. 212A / straight, angled No. 12
STANDARD BLADES
Diamond Knife Diamond BladeNo. 213 / tri-facet No. 13No. 213A / tri-facet, angled No. 13
0.171.0
45°
0.171.0
30°
3F
0.17width
60°
0.171.0
40°
45° 30°
0.171.0
45°
0.171.0
30°
B D
0.17width
60°
0.171.0
40°
AA1
STANDARD BLADES
Diamond Knife Diamond BladeNo. 271 / lance with blunt sides No. 71No. 271A / lance with blunt sides, angled No. 71
0.171.0
45°
0.171.0
30°
0.171.0
3F
0.17width
60°
45° 30°
A
B D
L
L
L
248A 248 lance with blunt sides 0.9 3.0 0.17 60° 48
271A 271 lance with blunt sides 1.0 3.0 0.17 40° 71
218A 218 lance with blunt sides 1.0 2.0 0.17 60° 18
220A 220 lance with blunt sides 1.0 3.0 0.17 60° 20
214SA 214S lance with blunt sides 1.2 3.0 0.17 60° 14S
214A 214 lance with blunt sides 1.4 3.0 0.17 60° 14
221A 221 lance with blunt sides 3.2 4.0 0.17 60° 21
spear
DIAMON D CUTTI NG I N STR U M E NTS FOR M ICROS U RG E RY
Amidia AG Telefon | Fax InternetMattenstrasse 11 +41 32 333 24 74 info@amidia.chCH-2555 Brügg +41 32 333 24 76 www.amidia.chSwitzerland
08 |
08
Page 7
STANDARD BLADES
Diamond Knife Diamond BladeNo. 248 / lance with blunt sides, width 0.9 mm No. 48No. 248A / lance with blunt sides, width 0.9 mm, angled No. 48No. 220 / lance with blunt sides, width 1.0 mm No. 20No. 220A / lance with blunt sides, width 1.0 mm, angled No. 20No. 214 / lance with blunt sides, width 1.4 mm No. 14No. 214A / lance with blunt sides, width 1.4 mm, angled No. 14
0.171.0
0.17width
60°
0.171.0
40°
PHACO BLADES
Diamond Knife Diamond BladeNo. 208 / spear with blunt sides, width 2.5 mm No. 08No. 208A / spear with blunt sides, width 2.5 mm, angled No. 08No. 243 / spear with blunt sides, width 2.8 mm No. 43No. 243A / spear with blunt sides, width 2.8 mm, angled No. 43No. 222 / spear with blunt sides, width 3.0 mm No. 22No. 222A / spear with blunt sides, width 3.0 mm, angled No. 22No. 223 / spear with blunt sides, width 3.2 mm No. 23No. 223A / spear with blunt sides, width 3.2 mm, angled No. 23
0.17
0.172.65
40°
1.0
0.55
0.2
Front Back
0.171.0
0.2
DB
TUNNEL BLADES
Diamond Knife Diamond BladeNo. 239 / NEW tunnel 9 facets, width 1.4 mm No. 39No. 239A / NEW tunnel 9 facets, width 1.4 mm, angled No. 39No. 254 / tunnel 9 facets, width 2.0 mm No. 54No. 254A / tunnel 9 facets, width 2.0 mm, angled No. 54
60°
0.17width
0.42.0
0.1
0.17width
90°
A
DB
L
L
230A 230 spear with blunt sides 1.0 2.0 0.17 90° 30
219A 219 spear with blunt sides 1.0 4.0 0.17 90° 19
229A 229 spear with blunt sides 1.4 4.0 0.17 90° 29
208A 208 spear with blunt sides 2.5 4.0 0.17 90° 08
243A 243 spear with blunt sides 2.8 4.0 0.17 90° 43
222A 222 spear with blunt sides 3.0 4.0 0.17 90° 22
223A 223 spear with blunt sides 3.2 4.0 0.17 90° 23
278A 278 spear with blunt sides 3.5 4.0 0.17 90° 78
tunnel
DIAMON D CUTTI NG I N STR U M E NTS FOR M ICROS U RG E RY
Amidia AG Telefon | Fax InternetMattenstrasse 11 +41 32 333 24 74 info@amidia.chCH-2555 Brügg +41 32 333 24 76 www.amidia.chSwitzerland
08 |
08
Page 7
STANDARD BLADES
Diamond Knife Diamond BladeNo. 248 / lance with blunt sides, width 0.9 mm No. 48No. 248A / lance with blunt sides, width 0.9 mm, angled No. 48No. 220 / lance with blunt sides, width 1.0 mm No. 20No. 220A / lance with blunt sides, width 1.0 mm, angled No. 20No. 214 / lance with blunt sides, width 1.4 mm No. 14No. 214A / lance with blunt sides, width 1.4 mm, angled No. 14
0.171.0
0.17width
60°
0.171.0
40°
PHACO BLADES
Diamond Knife Diamond BladeNo. 208 / spear with blunt sides, width 2.5 mm No. 08No. 208A / spear with blunt sides, width 2.5 mm, angled No. 08No. 243 / spear with blunt sides, width 2.8 mm No. 43No. 243A / spear with blunt sides, width 2.8 mm, angled No. 43No. 222 / spear with blunt sides, width 3.0 mm No. 22No. 222A / spear with blunt sides, width 3.0 mm, angled No. 22No. 223 / spear with blunt sides, width 3.2 mm No. 23No. 223A / spear with blunt sides, width 3.2 mm, angled No. 23
0.17
0.172.65
40°
1.0
0.55
0.2
Front Back
0.171.0
0.2
DB
TUNNEL BLADES
Diamond Knife Diamond BladeNo. 239 / NEW tunnel 9 facets, width 1.4 mm No. 39No. 239A / NEW tunnel 9 facets, width 1.4 mm, angled No. 39No. 254 / tunnel 9 facets, width 2.0 mm No. 54No. 254A / tunnel 9 facets, width 2.0 mm, angled No. 54
60°
0.17width
0.42.0
0.1
0.17width
90°
A
DB
L
L
239A 239 tunnel 19 facets 1.4 4.0 0.17 39
254A 254 tunnel 19 facets 2.0 4.0 0.17 54
258A 258 tunnel 19 facets 2.2 4.0 0.17 58
255A 255 tunnel 19 facets 2.5 4.0 0.17 55
253A 253 tunnel 19 facets 3.0 4.0 0.17 53
clear cornea MICS micro coaxial surgery
DIAMON D CUTTI NG I N STR U M E NTS FOR M ICROS U RG E RY
Amidia AG Telefon | Fax InternetMattenstrasse 11 +41 32 333 24 74 info@amidia.chCH-2555 Brügg +41 32 333 24 76 www.amidia.chSwitzerland
08 |
08
Page 8
0.17width
CLEAR CORNEA BLADES
Diamond Knife Diamond BladeNo. 298 / clear cornea with sharp sides, width 2.5 mm No. 98No. 298A / clear cornea with sharp sides, width 2.5 mm, angled No. 98No. 295 / clear cornea with sharp sides, width 2.6 mm No. 95No. 295A / clear cornea with sharp sides, width 2.6 mm, angled No. 95No. 277 / clear cornea with sharp sides, width 2.8 mm No. 77No. 277A / clear cornea with sharp sides, width 2.8 mm, angled No. 77No. 273 / clear cornea with sharp sides, width 3.0 mm No. 73No. 273A / clear cornea with sharp sides, width 3.0 mm, angled No. 73No. 274 / clear cornea with sharp sides, width 3.2 mm No. 74No. 274A / clear cornea with sharp sides, width 3.2 mm, angled No. 74
TAPERED SPEAR BLADES
Diamond Knife Diamond BladeNo. 290 / spear 4 facets with sharp sides, width 2.5-3.0 mm No. 90No. 290A / spear 4 facets with sharp sides, width 2.5-3.0 mm, angled No. 90No. 232 / spear 4 facets with sharp sides, width 2.75-3.2 mm No. 32No. 232A / spear 4 facets with sharp sides, width 2.75-3.2 mm, angled No. 32No. 240 / spear 4 facets with sharp sides, width 3.0-3.2 mm No. 40No. 240A / spear 4 facets with sharp sides, width 3.0-3.2 mm, angled No. 40No. 289 / spear 4 facets with sharp sides, width 3.2-3.5 mm No. 89No. 289A / spear 4 facets with sharp sides, width 3.2-3.5 mm, angled No. 89
TAPERED SPEAR BLADES
Diamond Knife Diamond BladeNo. 288 / spear 6 facets with sharp sides, width 2.65-3.2 mm No. 88No. 288A / spear 6 facets with sharp sides, width 2.65-3.2 mm, angled No. 88
60°
0.17width
D
B
0.17width
width
90°
60°
0.17width
0.17width
width
90°
A
A
B D
B1
A
DB
L
L
L
224-02A 224-02 clear cornea with sharp sides 1.0 4.0 0.17 90° 24-02
231A 231 clear cornea with sharp sides 1.6 4.0 0.17 90° 31
235A 235 clear cornea with sharp sides 1.7 4.0 0.17 90° 35
236A 236 clear cornea with sharp sides 1.8 4.0 0.17 90° 36
237A 237 clear cornea with sharp sides 1.9 4.0 0.17 90° 37
238A 238 clear cornea with sharp sides 2.0 4.0 0.17 90° 38
261A 261 clear cornea with sharp sides 2.1 4.0 0.17 90° 61
262A 262 clear cornea with sharp sides 2.2 4.0 0.17 90° 62
263A 263 clear cornea with sharp sides 2.3 4.0 0.17 90° 63
265A 265 clear cornea with sharp sides 2.4 4.0 0.17 90° 65
6
Amidia LTD Mattenstrasse 11 CH-2555 Brügg
Phone +41 32 333 24 74 Fax +41 32 333 24 76
Mail info@amidia.ch Web www.amidia.ch
B = width / L = length / D = thickness / A = angle
Diamond cutting instruments for micro surgery
drawingangled holder
straight holder description B1/B L D A/A1 blade
clear cornea 60°
DIAMON D CUTTI NG I N STR U M E NTS FOR M ICROS U RG E RY
Amidia AG Telefon | Fax InternetMattenstrasse 11 +41 32 333 24 74 info@amidia.chCH-2555 Brügg +41 32 333 24 76 www.amidia.chSwitzerland
08 |
08
Page 8
0.17width
CLEAR CORNEA BLADES
Diamond Knife Diamond BladeNo. 298 / clear cornea with sharp sides, width 2.5 mm No. 98No. 298A / clear cornea with sharp sides, width 2.5 mm, angled No. 98No. 295 / clear cornea with sharp sides, width 2.6 mm No. 95No. 295A / clear cornea with sharp sides, width 2.6 mm, angled No. 95No. 277 / clear cornea with sharp sides, width 2.8 mm No. 77No. 277A / clear cornea with sharp sides, width 2.8 mm, angled No. 77No. 273 / clear cornea with sharp sides, width 3.0 mm No. 73No. 273A / clear cornea with sharp sides, width 3.0 mm, angled No. 73No. 274 / clear cornea with sharp sides, width 3.2 mm No. 74No. 274A / clear cornea with sharp sides, width 3.2 mm, angled No. 74
TAPERED SPEAR BLADES
Diamond Knife Diamond BladeNo. 290 / spear 4 facets with sharp sides, width 2.5-3.0 mm No. 90No. 290A / spear 4 facets with sharp sides, width 2.5-3.0 mm, angled No. 90No. 232 / spear 4 facets with sharp sides, width 2.75-3.2 mm No. 32No. 232A / spear 4 facets with sharp sides, width 2.75-3.2 mm, angled No. 32No. 240 / spear 4 facets with sharp sides, width 3.0-3.2 mm No. 40No. 240A / spear 4 facets with sharp sides, width 3.0-3.2 mm, angled No. 40No. 289 / spear 4 facets with sharp sides, width 3.2-3.5 mm No. 89No. 289A / spear 4 facets with sharp sides, width 3.2-3.5 mm, angled No. 89
TAPERED SPEAR BLADES
Diamond Knife Diamond BladeNo. 288 / spear 6 facets with sharp sides, width 2.65-3.2 mm No. 88No. 288A / spear 6 facets with sharp sides, width 2.65-3.2 mm, angled No. 88
60°
0.17width
D
B
0.17width
width
90°
60°
0.17width
0.17width
width
90°
A
A
B D
B1
A
DB
L
L
L
297A 297 clear cornea with sharp sides 3.0 4.0 0.17 60° 97234A 234 clear cornea with sharp sides 3.2 4.0 0.17 60° 34
clear cornea 90°298A 298 clear cornea with sharp sides 2.5 4.0 0.17 90° 98272A 272 clear cornea with sharp sides 2.6 4.0 0.17 90° 72295A 295 clear cornea with sharp sides 2.65 4.0 0.17 90° 95277A 277 clear cornea with sharp sides 2.8 4.0 0.17 90° 77273A 273 clear cornea with sharp sides 3.0 4.0 0.17 90° 73274A 274 clear cornea with sharp sides 3.2 4.0 0.17 90° 74293A 293 clear cornea with sharp sides 3.5 4.0 0.17 90° 93
tapered spear MICS micro coaxial surgery
B
B1
L
D
A
279A 279 spear 4 facets with sharp sides 1.1-1.4 4.0 0.17 90° 79280A 280 spear 4 facets with sharp sides 1.5-1.8 4.0 0.17 90° 80282A 282 spear 4 facets with sharp sides 1.5-2.0 4.0 0.17 90° 82284-01A 284-01 spear 4 facets with sharp sides 1.7-2.0 4.0 0.17 90° 84-01284A 284 spear 4 facets with sharp sides 1.8-2.2 4.0 0.17 90° 84284-02A 284-02 spear 4 facets with sharp sides 2.0-2.3 4.0 0.17 90° 84-02284-04A 284-04 1 spear 4 facets with sharp sides 1.8-2.4 4.0 0.17 90° 84-04284-03A 284-03 spear 4 facets with sharp sides 2.4-2.7 4.0 0.17 90° 84-03284-05A 284-05 2 spear 4 facets with sharp sides 1.8-2.75 4.0 0.17 90° 84-05
1 and 2 with laserlines: 1) 1.8 / 2.0 / 2.2 / 2.4 2) 1.8 / 2.2 / 2.4 / 2.75
tapered spear 4 facets
B
B1
L
D
A
291A 291 spear 4 facets with sharp sides 2.5-3.0 4.0 0.10 90° 91290A 290 spear 4 facets with sharp sides 2.5-3.0 4.0 0.17 90° 90292A 292 spear 4 facets with sharp sides 2.7-2.9 4.0 0.17 90° 92232A 232 spear 4 facets with sharp sides 2.75-3.2 4.0 0.17 90° 32240A 240 spear 4 facets with sharp sides 3.0-3.2 4.0 0.17 90° 40233A 233 spear 4 facets with sharp sides 3.0-3.5 4.0 0.17 90° 33289A 289 spear 4 facets with sharp sides 3.2-3.5 4.0 0.17 90° 89
tapered spear 6 facets
DIAMON D CUTTI NG I N STR U M E NTS FOR M ICROS U RG E RY
Amidia AG Telefon | Fax InternetMattenstrasse 11 +41 32 333 24 74 info@amidia.chCH-2555 Brügg +41 32 333 24 76 www.amidia.chSwitzerland
08 |
08
Page 8
0.17width
CLEAR CORNEA BLADES
Diamond Knife Diamond BladeNo. 298 / clear cornea with sharp sides, width 2.5 mm No. 98No. 298A / clear cornea with sharp sides, width 2.5 mm, angled No. 98No. 295 / clear cornea with sharp sides, width 2.6 mm No. 95No. 295A / clear cornea with sharp sides, width 2.6 mm, angled No. 95No. 277 / clear cornea with sharp sides, width 2.8 mm No. 77No. 277A / clear cornea with sharp sides, width 2.8 mm, angled No. 77No. 273 / clear cornea with sharp sides, width 3.0 mm No. 73No. 273A / clear cornea with sharp sides, width 3.0 mm, angled No. 73No. 274 / clear cornea with sharp sides, width 3.2 mm No. 74No. 274A / clear cornea with sharp sides, width 3.2 mm, angled No. 74
TAPERED SPEAR BLADES
Diamond Knife Diamond BladeNo. 290 / spear 4 facets with sharp sides, width 2.5-3.0 mm No. 90No. 290A / spear 4 facets with sharp sides, width 2.5-3.0 mm, angled No. 90No. 232 / spear 4 facets with sharp sides, width 2.75-3.2 mm No. 32No. 232A / spear 4 facets with sharp sides, width 2.75-3.2 mm, angled No. 32No. 240 / spear 4 facets with sharp sides, width 3.0-3.2 mm No. 40No. 240A / spear 4 facets with sharp sides, width 3.0-3.2 mm, angled No. 40No. 289 / spear 4 facets with sharp sides, width 3.2-3.5 mm No. 89No. 289A / spear 4 facets with sharp sides, width 3.2-3.5 mm, angled No. 89
TAPERED SPEAR BLADES
Diamond Knife Diamond BladeNo. 288 / spear 6 facets with sharp sides, width 2.65-3.2 mm No. 88No. 288A / spear 6 facets with sharp sides, width 2.65-3.2 mm, angled No. 88
60°
0.17width
D
B
0.17width
width
90°
60°
0.17width
0.17width
width
90°
A
A
B D
B1
A
DB
L
L
L
288A 288 spear 6 facets with sharp sided 2.65-3.2 4.0 0.17 90° 88283A 283 spear 6 facets with sharp sides 3.0-3.2 4.0 0.17 90° 83
Amidia LTD Mattenstrasse 11 CH-2555 Brügg
Phone +41 32 333 24 74 Fax +41 32 333 24 76
Mail info@amidia.ch Web www.amidia.ch 7
B = width / L = length / D = thickness / A = angle
Diamond cutting instruments for micro surgery
Diamond knives for cataract surgery (titanium bajonet handle with the j-slot mechanism)
The Amidia bayonet handle is made out of best quality titanium material.Each diamond blade goes with a straight blade holder or a 30 degree angled holder.
drawingangled holder
straight holder description B L D A/A1 blade
straight / single edge
DIAMON D CUTTI NG I N STR U M E NTS FOR M ICROS U RG E RY
Amidia AG Telefon | Fax InternetMattenstrasse 11 +41 32 333 24 74 info@amidia.chCH-2555 Brügg +41 32 333 24 76 www.amidia.chSwitzerland
08 |
08
Page 12
0.171.0
30°
0.171.0
3F
0.17width
60°
0.171.0
40°
45° 30°
• The amidia bayonet handle is made out of best quality TITAN and MEDICAL STEEL material.• Available with all diamond blades you will find in our leaflets, for pencil handle.• Each diamond blade goes with a straight blade holder, or 30 degree angled holder (A in the Article No. means 30 degree angled)
STANDARD BLADES
Diamond Knife Diamond BladeNo. 311 / straight No. 11No. 311A / straight, angled No. 11
STANDARD BLADES
Diamond Knife Diamond BladeNo. 312 / straight No. 12No. 312A / straight, angled No. 12
STANDARD BLADES
Diamond Knife Diamond BladeNo. 313 / tri-facet No. 13No. 313A / tri-facet, angled No. 13
STANDARD BLADES
Diamond Knife Diamond BladeNo. 371 / lance with blunt sides No. 71No. 371A / lance with blunt sides, angled No. 71
TITAN Bayonet Handle No. 300
0.171.0
45°
0.171.0
3F
0.17width
60°
0.171.0
40°
45° 30°
0.171.0
45°
0.171.0
30°
3F
0.17width
60°
0.171.0
40°
0.171.0
45°
0.171.0
30°
0.171.0
3F
0.17width
60°
45° 30°
B
B
B
B
A
A
A1A
A
D
D
D
D
L
L
L
L
316A 316 straight 0.7 2.0 0.17 30° 16
387A 387 straight 1.0 2.0 0.17 30° 87
312A 312 straight 1.0 3.0 0.17 30° 12
364SA 364S straight 1.5 4.0 0.17 30° 64S
315A 315 straight 0.7 2.0 0.17 45° 15
311A 311 straight 1.0 3.0 0.17 45° 11
310A 310 straight 1.5 3.0 0.17 45° 10
311SA 311S straight 2.0 3.0 0.17 45° 11S
tri-facet
DIAMON D CUTTI NG I N STR U M E NTS FOR M ICROS U RG E RY
Amidia AG Telefon | Fax InternetMattenstrasse 11 +41 32 333 24 74 info@amidia.chCH-2555 Brügg +41 32 333 24 76 www.amidia.chSwitzerland
08 |
08
Page 12
0.171.0
30°
0.171.0
3F
0.17width
60°
0.171.0
40°
45° 30°
• The amidia bayonet handle is made out of best quality TITAN and MEDICAL STEEL material.• Available with all diamond blades you will find in our leaflets, for pencil handle.• Each diamond blade goes with a straight blade holder, or 30 degree angled holder (A in the Article No. means 30 degree angled)
STANDARD BLADES
Diamond Knife Diamond BladeNo. 311 / straight No. 11No. 311A / straight, angled No. 11
STANDARD BLADES
Diamond Knife Diamond BladeNo. 312 / straight No. 12No. 312A / straight, angled No. 12
STANDARD BLADES
Diamond Knife Diamond BladeNo. 313 / tri-facet No. 13No. 313A / tri-facet, angled No. 13
STANDARD BLADES
Diamond Knife Diamond BladeNo. 371 / lance with blunt sides No. 71No. 371A / lance with blunt sides, angled No. 71
TITAN Bayonet Handle No. 300
0.171.0
45°
0.171.0
3F
0.17width
60°
0.171.0
40°
45° 30°
0.171.0
45°
0.171.0
30°
3F
0.17width
60°
0.171.0
40°
0.171.0
45°
0.171.0
30°
0.171.0
3F
0.17width
60°
45° 30°
B
B
B
B
A
A
A1A
A
D
D
D
D
L
L
L
L
317A 317 tri-facet 0.7 2.0 0.17 45°/30° 17
313A 313 tri-facet 1.0 3.0 0.17 45°/30° 13
curved
D
L
B
4F
324A 324 curved 4 facets 1.0 3.0 0.17 24
also available in
a peek handle
8
Amidia LTD Mattenstrasse 11 CH-2555 Brügg
Phone +41 32 333 24 74 Fax +41 32 333 24 76
Mail info@amidia.ch Web www.amidia.ch
B = width / L = length / D = thickness / A = angle
Diamond cutting instruments for micro surgery
drawingangled holder
straight holder description B L D A/A1 blade
lance
DIAMON D CUTTI NG I N STR U M E NTS FOR M ICROS U RG E RY
Amidia AG Telefon | Fax InternetMattenstrasse 11 +41 32 333 24 74 info@amidia.chCH-2555 Brügg +41 32 333 24 76 www.amidia.chSwitzerland
08 |
08
Page 12
0.171.0
30°
0.171.0
3F
0.17width
60°
0.171.0
40°
45° 30°
• The amidia bayonet handle is made out of best quality TITAN and MEDICAL STEEL material.• Available with all diamond blades you will find in our leaflets, for pencil handle.• Each diamond blade goes with a straight blade holder, or 30 degree angled holder (A in the Article No. means 30 degree angled)
STANDARD BLADES
Diamond Knife Diamond BladeNo. 311 / straight No. 11No. 311A / straight, angled No. 11
STANDARD BLADES
Diamond Knife Diamond BladeNo. 312 / straight No. 12No. 312A / straight, angled No. 12
STANDARD BLADES
Diamond Knife Diamond BladeNo. 313 / tri-facet No. 13No. 313A / tri-facet, angled No. 13
STANDARD BLADES
Diamond Knife Diamond BladeNo. 371 / lance with blunt sides No. 71No. 371A / lance with blunt sides, angled No. 71
TITAN Bayonet Handle No. 300
0.171.0
45°
0.171.0
3F
0.17width
60°
0.171.0
40°
45° 30°
0.171.0
45°
0.171.0
30°
3F
0.17width
60°
0.171.0
40°
0.171.0
45°
0.171.0
30°
0.171.0
3F
0.17width
60°
45° 30°
B
B
B
B
A
A
A1A
A
D
D
D
D
L
L
L
L
318A 318 lance with blunt sides 1.0 2.0 0.17 60° 18
348A 348 lance with blunt sides 0.9 3.0 0.17 60° 48
371A 371 lance with blunt sides 1.0 3.0 0.17 40° 71
320A 320 lance with blunt sides 1.0 3.0 0.17 60° 20
314SA 314S lance with blunt sides 1.2 3.0 0.17 60° 14S
314A 314 lance with blunt sides 1.4 3.0 0.17 60° 14
321A 321 lance with blunt sides 3.2 4.0 0.17 60° 21
spear
DIAMON D CUTTI NG I N STR U M E NTS FOR M ICROS U RG E RY
Amidia AG Telefon | Fax InternetMattenstrasse 11 +41 32 333 24 74 info@amidia.chCH-2555 Brügg +41 32 333 24 76 www.amidia.chSwitzerland
08 |
08
Page 13
STANDARD BLADES
Diamond Knife Diamond BladeNo. 348 / lance with blunt sides, width 0.9 mm No. 48No. 348A / lance with blunt sides, width 0.9 mm, angled No. 48No. 320 / lance with blunt sides, width 1.0 mm No. 20No. 320A / lance with blunt sides, width 1.0 mm, angled No. 20No. 314 / lance with blunt sides, width 1.4 mm No. 14No. 314A / lance with blunt sides, width 1.4 mm, angled No. 14
0.171.0
0.171.0
40°
PHACO BLADES
Diamond Knife Diamond BladeNo. 308 / spear with blunt sides, width 2.5 mm No. 08No. 308A / spear with blunt sides, width 2.5 mm, angled No. 08No. 343 / spear with blunt sides, width 2.8 mm No. 43No. 343A / spear with blunt sides, width 2.8 mm, angled No. 43No. 322 / spear with blunt sides, width 3.0 mm No. 22No. 322A / spear with blunt sides, width 3.0 mm, angled No. 22No. 323 / spear with blunt sides, width 3.2 mm No. 23No. 323A / spear with blunt sides, width 3.2 mm, angled No. 23
0.17
0.172.65
40°
1.0
0.2
Front Back
0.171.0
0.2
TUNNEL BLADES
Diamond Knife Diamond BladeNo. 339 / NEW tunnel 9 facets, width 1.4 mm No. 39No. 339A / NEW tunnel 9 facets, width 1.4 mm, angled No. 39No. 354 / tunnel 9 facets, width 2.0 mm No. 54No. 354A / tunnel 9 facets, width 2.0 mm, angled No. 54
60°
0.17width
0.42.0
0.1
0.17width
90°
A
A
D
D
D
B
B
B
L
L
L
330A 330 spear with blunt sides 1.0 2.0 0.17 90° 30
319A 319 spear with blunt sides 1.0 4.0 0.17 90° 19
329A 329 spear with blunt sides 1.4 4.0 0.17 90° 29
307A 307 spear with blunt sides 2.2 4.0 0.17 90° 07
308A 308 spear with blunt sides 2.5 4.0 0.17 90° 08
343A 343 spear with blunt sides 2.8 4.0 0.17 90° 43
322A 322 spear with blunt sides 3.0 4.0 0.17 90° 22
323A 323 spear with blunt sides 3.2 4.0 0.17 90° 23
378A 378 spear with blunt sides 3.5 4.0 0.17 90° 78
tunnel
DIAMON D CUTTI NG I N STR U M E NTS FOR M ICROS U RG E RY
Amidia AG Telefon | Fax InternetMattenstrasse 11 +41 32 333 24 74 info@amidia.chCH-2555 Brügg +41 32 333 24 76 www.amidia.chSwitzerland
08 |
08
Page 13
STANDARD BLADES
Diamond Knife Diamond BladeNo. 348 / lance with blunt sides, width 0.9 mm No. 48No. 348A / lance with blunt sides, width 0.9 mm, angled No. 48No. 320 / lance with blunt sides, width 1.0 mm No. 20No. 320A / lance with blunt sides, width 1.0 mm, angled No. 20No. 314 / lance with blunt sides, width 1.4 mm No. 14No. 314A / lance with blunt sides, width 1.4 mm, angled No. 14
0.171.0
0.171.0
40°
PHACO BLADES
Diamond Knife Diamond BladeNo. 308 / spear with blunt sides, width 2.5 mm No. 08No. 308A / spear with blunt sides, width 2.5 mm, angled No. 08No. 343 / spear with blunt sides, width 2.8 mm No. 43No. 343A / spear with blunt sides, width 2.8 mm, angled No. 43No. 322 / spear with blunt sides, width 3.0 mm No. 22No. 322A / spear with blunt sides, width 3.0 mm, angled No. 22No. 323 / spear with blunt sides, width 3.2 mm No. 23No. 323A / spear with blunt sides, width 3.2 mm, angled No. 23
0.17
0.172.65
40°
1.0
0.2
Front Back
0.171.0
0.2
TUNNEL BLADES
Diamond Knife Diamond BladeNo. 339 / NEW tunnel 9 facets, width 1.4 mm No. 39No. 339A / NEW tunnel 9 facets, width 1.4 mm, angled No. 39No. 354 / tunnel 9 facets, width 2.0 mm No. 54No. 354A / tunnel 9 facets, width 2.0 mm, angled No. 54
60°
0.17width
0.42.0
0.1
0.17width
90°
A
A
D
D
D
B
B
B
L
L
L
339A 339 tunnel 19 facets 1.4 4.0 0.17 39
354A 354 tunnel 19 facets 2.0 4.0 0.17 54
358A 358 tunnel 19 facets 2.2 4.0 0.17 58
355A 355 tunnel 19 facets 2.5 4.0 0.17 55
353A 353 tunnel 19 facets 3.0 4.0 0.17 53
clear cornea MICS micro coaxial surgery
DIAMON D CUTTI NG I N STR U M E NTS FOR M ICROS U RG E RY
Amidia AG Telefon | Fax InternetMattenstrasse 11 +41 32 333 24 74 info@amidia.chCH-2555 Brügg +41 32 333 24 76 www.amidia.chSwitzerland
08 |
08Page 8
0.17width
CLEAR CORNEA BLADES
Diamond Knife Diamond BladeNo. 298 / clear cornea with sharp sides, width 2.5 mm No. 98No. 298A / clear cornea with sharp sides, width 2.5 mm, angled No. 98No. 295 / clear cornea with sharp sides, width 2.6 mm No. 95No. 295A / clear cornea with sharp sides, width 2.6 mm, angled No. 95No. 277 / clear cornea with sharp sides, width 2.8 mm No. 77No. 277A / clear cornea with sharp sides, width 2.8 mm, angled No. 77No. 273 / clear cornea with sharp sides, width 3.0 mm No. 73No. 273A / clear cornea with sharp sides, width 3.0 mm, angled No. 73No. 274 / clear cornea with sharp sides, width 3.2 mm No. 74No. 274A / clear cornea with sharp sides, width 3.2 mm, angled No. 74
TAPERED SPEAR BLADES
Diamond Knife Diamond BladeNo. 290 / spear 4 facets with sharp sides, width 2.5-3.0 mm No. 90No. 290A / spear 4 facets with sharp sides, width 2.5-3.0 mm, angled No. 90No. 232 / spear 4 facets with sharp sides, width 2.75-3.2 mm No. 32No. 232A / spear 4 facets with sharp sides, width 2.75-3.2 mm, angled No. 32No. 240 / spear 4 facets with sharp sides, width 3.0-3.2 mm No. 40No. 240A / spear 4 facets with sharp sides, width 3.0-3.2 mm, angled No. 40No. 289 / spear 4 facets with sharp sides, width 3.2-3.5 mm No. 89No. 289A / spear 4 facets with sharp sides, width 3.2-3.5 mm, angled No. 89
TAPERED SPEAR BLADES
Diamond Knife Diamond BladeNo. 288 / spear 6 facets with sharp sides, width 2.65-3.2 mm No. 88No. 288A / spear 6 facets with sharp sides, width 2.65-3.2 mm, angled No. 88
60°
0.17width
D
B
0.17width
width
90°
60°
0.17width
0.17width
width
90°
A
A
B D
B1
A
DB
L
L
L
324-02A 324-02 clear cornea with sharp sides 1.0 4.0 0.17 90° 24-02
331A 331 clear cornea with sharp sides 1.6 4.0 0.17 90° 31
335A 335 clear cornea with sharp sides 1.7 4.0 0.17 90° 35
336A 336 clear cornea with sharp sides 1.8 4.0 0.17 90° 36
337A 337 clear cornea with sharp sides 1.9 4.0 0.17 90° 37
338A 338 clear cornea with sharp sides 2.0 4.0 0.17 90° 38
361A 361 clear cornea with sharp sides 2.1 4.0 0.17 90° 61
362A 362 clear cornea with sharp sides 2.2 4.0 0.17 90° 62
363A 363 clear cornea with sharp sides 2.3 4.0 0.17 90° 63
365A 365 clear cornea with sharp sides 2.4 4.0 0.17 90° 65
Amidia LTD Mattenstrasse 11 CH-2555 Brügg
Phone +41 32 333 24 74 Fax +41 32 333 24 76
Mail info@amidia.ch Web www.amidia.ch 9
B = width / L = length / D = thickness / A = angle
Diamond cutting instruments for micro surgery
drawingangled holder
straight holder description B1/B L D A/A1 blade
clear cornea 60°
DIAMON D CUTTI NG I N STR U M E NTS FOR M ICROS U RG E RY
Amidia AG Telefon | Fax InternetMattenstrasse 11 +41 32 333 24 74 info@amidia.chCH-2555 Brügg +41 32 333 24 76 www.amidia.chSwitzerland
08 |
08
Page 8
0.17width
CLEAR CORNEA BLADES
Diamond Knife Diamond BladeNo. 298 / clear cornea with sharp sides, width 2.5 mm No. 98No. 298A / clear cornea with sharp sides, width 2.5 mm, angled No. 98No. 295 / clear cornea with sharp sides, width 2.6 mm No. 95No. 295A / clear cornea with sharp sides, width 2.6 mm, angled No. 95No. 277 / clear cornea with sharp sides, width 2.8 mm No. 77No. 277A / clear cornea with sharp sides, width 2.8 mm, angled No. 77No. 273 / clear cornea with sharp sides, width 3.0 mm No. 73No. 273A / clear cornea with sharp sides, width 3.0 mm, angled No. 73No. 274 / clear cornea with sharp sides, width 3.2 mm No. 74No. 274A / clear cornea with sharp sides, width 3.2 mm, angled No. 74
TAPERED SPEAR BLADES
Diamond Knife Diamond BladeNo. 290 / spear 4 facets with sharp sides, width 2.5-3.0 mm No. 90No. 290A / spear 4 facets with sharp sides, width 2.5-3.0 mm, angled No. 90No. 232 / spear 4 facets with sharp sides, width 2.75-3.2 mm No. 32No. 232A / spear 4 facets with sharp sides, width 2.75-3.2 mm, angled No. 32No. 240 / spear 4 facets with sharp sides, width 3.0-3.2 mm No. 40No. 240A / spear 4 facets with sharp sides, width 3.0-3.2 mm, angled No. 40No. 289 / spear 4 facets with sharp sides, width 3.2-3.5 mm No. 89No. 289A / spear 4 facets with sharp sides, width 3.2-3.5 mm, angled No. 89
TAPERED SPEAR BLADES
Diamond Knife Diamond BladeNo. 288 / spear 6 facets with sharp sides, width 2.65-3.2 mm No. 88No. 288A / spear 6 facets with sharp sides, width 2.65-3.2 mm, angled No. 88
60°
0.17width
D
B
0.17width
width
90°
60°
0.17width
0.17width
width
90°
A
A
B D
B1
A
DB
L
L
L
397A 397 clear cornea with sharp sides 3.0 4.0 0.17 60° 97334A 334 clear cornea with sharp sides 3.2 4.0 0.17 60° 34
clear cornea 90°398A 398 clear cornea with sharp sides 2.5 4.0 0.17 90° 98372A 372 clear cornea with sharp sides 2.6 4.0 0.17 90° 72395A 395 clear cornea with sharp sides 2.65 4.0 0.17 90° 95377A 377 clear cornea with sharp sides 2.8 4.0 0.17 90° 77373A 373 clear cornea with sharp sides 3.0 4.0 0.17 90° 73374A 374 clear cornea with sharp sides 3.2 4.0 0.17 90° 74393A 393 clear cornea with sharp sides 3.5 4.0 0.17 90° 93
tapered spear MICS micro coaxial surgery
B
B1
L
D
A
379A 379 spear 4 facets with sharp sides 1.1-1.4 4.0 0.17 90° 79380A 380 spear 4 facets with sharp sides 1.5-1.8 4.0 0.17 90° 80382A 382 spear 4 facets with sharp sides 1.5-2.0 4.0 0.17 90° 82384-01A 384-01 spear 4 facets with sharp sides 1.7-2.0 4.0 0.17 90° 84-01384A 384 spear 4 facets with sharp sides 1.8-2.2 4.0 0.17 90° 84384-02A 384-02 spear 4 facets with sharp sides 2.0-2.3 4.0 0.17 90° 84-02384-04A 384-04 1 spear 4 facets with sharp sides 1.8-2.4 4.0 0.17 90° 84-04384-03A 384-03 spear 4 facets with sharp sides 2.4-2.7 4.0 0.17 90° 84-03384-05A 384-05 2 spear 4 facets with sharp sides 1.8-2.75 4.0 0.17 90° 84-05
1 and 2 with laserlines: 1) 1.8 / 2.0 / 2.2 / 2.4 2) 1.8 / 2.2 / 2.4 / 2.75
tapered spear 4 facets
B
B1
L
D
A
391A 391 spear 4 facets with sharp sides 2.5-3.0 4.0 0.10 90° 91390A 390 spear 4 facets with sharp sides 2.5-3.0 4.0 0.17 90° 90392A 392 spear 4 facets with sharp sides 2.7-2.9 4.0 0.17 90° 92332A 332 spear 4 facets with sharp sides 2.75-3.2 4.0 0.17 90° 32340A 340 spear 4 facets with sharp sides 3.0-3.2 4.0 0.17 90° 40333A 333 spear 4 facets with sharp sides 3.0-3.5 4.0 0.17 90° 33389A 389 spear 4 facets with sharp sides 3.2-3.5 4.0 0.17 90° 89
tapered spear 6 facets
DIAMON D CUTTI NG I N STR U M E NTS FOR M ICROS U RG E RY
Amidia AG Telefon | Fax InternetMattenstrasse 11 +41 32 333 24 74 info@amidia.chCH-2555 Brügg +41 32 333 24 76 www.amidia.chSwitzerland
08 |
08
Page 8
0.17width
CLEAR CORNEA BLADES
Diamond Knife Diamond BladeNo. 298 / clear cornea with sharp sides, width 2.5 mm No. 98No. 298A / clear cornea with sharp sides, width 2.5 mm, angled No. 98No. 295 / clear cornea with sharp sides, width 2.6 mm No. 95No. 295A / clear cornea with sharp sides, width 2.6 mm, angled No. 95No. 277 / clear cornea with sharp sides, width 2.8 mm No. 77No. 277A / clear cornea with sharp sides, width 2.8 mm, angled No. 77No. 273 / clear cornea with sharp sides, width 3.0 mm No. 73No. 273A / clear cornea with sharp sides, width 3.0 mm, angled No. 73No. 274 / clear cornea with sharp sides, width 3.2 mm No. 74No. 274A / clear cornea with sharp sides, width 3.2 mm, angled No. 74
TAPERED SPEAR BLADES
Diamond Knife Diamond BladeNo. 290 / spear 4 facets with sharp sides, width 2.5-3.0 mm No. 90No. 290A / spear 4 facets with sharp sides, width 2.5-3.0 mm, angled No. 90No. 232 / spear 4 facets with sharp sides, width 2.75-3.2 mm No. 32No. 232A / spear 4 facets with sharp sides, width 2.75-3.2 mm, angled No. 32No. 240 / spear 4 facets with sharp sides, width 3.0-3.2 mm No. 40No. 240A / spear 4 facets with sharp sides, width 3.0-3.2 mm, angled No. 40No. 289 / spear 4 facets with sharp sides, width 3.2-3.5 mm No. 89No. 289A / spear 4 facets with sharp sides, width 3.2-3.5 mm, angled No. 89
TAPERED SPEAR BLADES
Diamond Knife Diamond BladeNo. 288 / spear 6 facets with sharp sides, width 2.65-3.2 mm No. 88No. 288A / spear 6 facets with sharp sides, width 2.65-3.2 mm, angled No. 88
60°
0.17width
D
B
0.17width
width
90°
60°
0.17width
0.17width
width
90°
A
A
B D
B1
A
DB
L
L
L
388A 388 spear 6 facets with sharp sided 2.65-3.2 4.0 0.17 90° 88383A 383 spear 6 facets with sharp sides 3.0-3.2 4.0 0.17 90° 83
10
Amidia LTD Mattenstrasse 11 CH-2555 Brügg
Phone +41 32 333 24 74 Fax +41 32 333 24 76
Mail info@amidia.ch Web www.amidia.ch
B = width / L = length / D = thickness / A = angle
Diamond cutting instruments for micro surgery
3D diamond knives
drawingangled holder
straight holder description B L D A blade
A
L
DB
A-3D-02A A-3D-02 3D-blade with sharp sides 1.4mm 4.0 0.17 80° 3D-02
A-3D-03A A-3D-03 3D-blade with sharp sides 1.5mm 4.0 0.17 80° 3D-03
A-3D-04A A-3D-04 3D-blade with sharp sides 1.6mm 4.0 0.17 80° 3D-04
A-3D-05A A-3D-05 3D-blade with sharp sides 1.7mm 4.0 0.17 80° 3D-05
A-3D-06A A-3D-06 3D-blade with sharp sides 1.8mm 4.0 0.17 80° 3D-06
A-3D-07A A-3D-07 3D-blade with sharp sides 1.9mm 4.0 0.17 80° 3D-07
A-3D-08A A-3D-08 3D-blade with sharp sides 2.0mm 4.0 0.17 80° 3D-08
A-3D-09A A-3D-09 3D-blade with sharp sides 2.1mm 4.0 0.17 80° 3D-09
A-3D-10A A-3D-10 3D-blade with sharp sides 2.2mm 4.0 0.17 80° 3D-10
A-3D-11A A-3D-11 3D-blade with sharp sides 2.3mm 4.0 0.17 80° 3D-11
A-3D-12A A-3D-12 3D-blade with sharp sides 2.4mm 4.0 0.17 80° 3D-12
A-3D-13A A-3D-13 3D-blade with sharp sides 2.5mm 4.0 0.17 80° 3D-13
A-3D-14A A-3D-14 3D-blade with sharp sides 2.6mm 4.0 0.17 80° 3D-14
A-3D-15A A-3D-15 3D-blade with sharp sides 2.65mm 4.0 0.17 80° 3D-15
A-3D-16A A-3D-16 3D-blade with sharp sides 2.7mm 4.0 0.17 80° 3D-16
A-3D-17A A-3D-17 3D-blade with sharp sides 2.8mm 4.0 0.17 80° 3D-17
A-3D-18A A-3D-18 3D-blade with sharp sides 2.9mm 4.0 0.17 80° 3D-18
A-3D-19A A-3D-19 3D-blade with sharp sides 3.0mm 4.0 0.17 80° 3D-19
A-3D-20A A-3D-20 3D-blade with sharp sides 3.1mm 4.0 0.17 80° 3D-20
A-3D-21A A-3D-21 3D-blade with sharp sides 3.2mm 4.0 0.17 80° 3D-21
Amidia LTD Mattenstrasse 11 CH-2555 Brügg
Phone +41 32 333 24 74 Fax +41 32 333 24 76
Mail info@amidia.ch Web www.amidia.ch 11
B = width / L = length / D = thickness / A = angle
Diamond cutting instruments for micro surgery
drawing article no. description B B1 L D A blade
Zaldivar multi purpose knife
B
L
D
B1 333-01 1.0 0.55 4.5 0.17 33-01
knife with straight holder
A
B
L
D
301-01 0.5 3.5 0.2 20° 01-01
step knife
A
B
L
D
B1 820-01 1.0 0.3 3.5 0.17 25° 20-01
steps: 0.15 / 0.2 / 0.25 / 0.3 / 0.37 / 0.5 / 4.0
Diamond knives for glaucoma surgery
0 0.50
4.00
0
0 0.50
4.00
0
12
Amidia LTD Mattenstrasse 11 CH-2555 Brügg
Phone +41 32 333 24 74 Fax +41 32 333 24 76
Mail info@amidia.ch Web www.amidia.ch
B = width / L = length / D = thickness / A = angle
Diamond cutting instruments for micro surgery
Diamond knives for LRI surgery (Limbal relaxing incision, LRI)
drawingRubenstein LRI-knives with fixed cutting depth either 500, 550 or 600 microns. B D A blade
short handle (7.6 cm)
1.0
60°
820-05-S50 0.50 preset cutting depth 1.0 0.17 60° 20-05
820-05-S55 0.55 preset cutting depth
820-05-S60 0.60 preset cutting depth
standard handle:
1.0
60°
820-05-L50 0.50 preset cutting depth 1.0 0.17 60° 20-05
820-05-L55 0.55 preset cutting depth
820-05-L60 0.60 preset cutting depth
Features:• winged footplate• improved view during surgery• footplate allows the blade to glide across the corneal epithelium• easy to control
Amidia LTD Mattenstrasse 11 CH-2555 Brügg
Phone +41 32 333 24 74 Fax +41 32 333 24 76
Mail info@amidia.ch Web www.amidia.ch 13
B = width / L = length / D = thickness / A = angle
Diamond cutting instruments for micro surgery
drawing article no. description B B1 L D A blade
with 3 settings: 0.5, 0.55, 0.6
B1
AL
S
DB
820-02 1.0 0.4 3.0 0.1 20° 20-02
with 1 setting
B1
AL
S
DB
820-02-01 0.5 1.0 0.4 3.0 0.1 20° 20-02
820-02-02 0.55 1.0 0.4 3.0 0.1 20° 20-02
820-02-03 0.6 1.0 0.4 3.0 0.1 20° 20-02
Donnenfeld LRI knife B B1 S D A blade
B
B1
D
S
A
820-03 1 setting at 0.6 0.8 0.25 0.6 0.17 20° 20-03
Features:• single footplate design with
a fixed depth of 0.6mm• the shorter handle
length promotes ease of use under the microscope or at the slit lamp
• the blade assembly retracts into handle for safe storage
Nichamin LRI knife B B1 D A blade820-04 0.8 0.2 0.1 15° 20-04
Features:• very small footplate• better visualization for the surgeon• excellent control while creating the incision
• diamond with a micro-flat tip• accurate for techniques utilizing pachymetry• steps: 0.45, 0.5, 0.55, 0.65, 0.7, 0.75
Diamond knives for LRI surgery
0.60
0.55
0.50
0.60
0.55
0.50
0
0.60
0.65
0.70
0
0.60
0.65
0.70
14
Amidia LTD Mattenstrasse 11 CH-2555 Brügg
Phone +41 32 333 24 74 Fax +41 32 333 24 76
Mail info@amidia.ch Web www.amidia.ch
15
20
15
25
3015
20
15
25
30
B = width / L = length / D = thickness / A = angle
Diamond cutting instruments for micro surgery
Diamond knives with a micrometer for refractive surgeryEach depth can be adjusted without steps. The scale is divided each hundredth millimeter (0 - 1.5) t = blade thickness of 0.1mm
drawing article no. description B L D A/A1 blade
straight
DIAMON D CUTTI NG I N STR U M E NTS FOR M ICROS U RG E RY
Amidia AG Telefon | Fax InternetMattenstrasse 11 +41 32 333 24 74 info@amidia.chCH-2555 Brügg +41 32 333 24 76 www.amidia.chSwitzerland
08 |
08
Page 27
0.171.0
30°
0.171.0
3F
0.171.5
45 °
0.171.0
45° 30°
• The amidia micrometer handle is made out of best quality TITAN and MEDICAL STEEL material.• Each depth of the blade can be adjusted without steps. The scale is divided each hundredth millimeter.• Available with all diamond blades you will find in our leaflets, for micrometer handle.
STANDARD BLADES
Diamond Knife Diamond BladeNo. 511 / straight No. 11No. 511T / straight No. 11
STANDARD BLADES
Diamond Knife Diamond BladeNo. 512 / straight No. 12No. 512T / straight No. 12
STANDARD BLADES
Diamond Knife Diamond BladeNo. 513 / tri-facet No. 13No. 513T / tri-facet No. 13
STANDARD BLADES
Diamond Knife Diamond BladeNo. 525 / axe No. 25No. 525T / axe No. 25
STANDARD BLADES
Diamond Knife Diamond BladeNo. 526 / triple edge vertical No. 26No. 526T / triple edge vertical No. 26
TITAN Micrometer Handle No. 500
0.171.0
45°
0.171.0
3F
0.171.5
45°
0.171.0
45° 30°
0.171.0
45°
0.171.0
30°
3F
0.171.5
45°
0.171.0
0.171.0
45°
0.171.0
30°
0.171.0
3F
0.171.0
45° 30°
0.171.0
45°
0.171.0
30°
0.171.0
3F
0.171.5
45°
45° 30°
A
A A1
A
B
B
B
B
B D
D
D
D
D
A
L
L
L
L
L
511 straight 1.0 3.0 0.17 45° 11
511t straight 0.9 3.0 0.1 45° 11t
512 straight 1.0 3.0 0.17 30° 12
512t straight 1.0 3.0 0.1 30° 12t
tri-facet
DIAMON D CUTTI NG I N STR U M E NTS FOR M ICROS U RG E RY
Amidia AG Telefon | Fax InternetMattenstrasse 11 +41 32 333 24 74 info@amidia.chCH-2555 Brügg +41 32 333 24 76 www.amidia.chSwitzerland
08 |
08
Page 27
0.171.0
30°
0.171.0
3F
0.171.5
45 °
0.171.0
45° 30°
• The amidia micrometer handle is made out of best quality TITAN and MEDICAL STEEL material.• Each depth of the blade can be adjusted without steps. The scale is divided each hundredth millimeter.• Available with all diamond blades you will find in our leaflets, for micrometer handle.
STANDARD BLADES
Diamond Knife Diamond BladeNo. 511 / straight No. 11No. 511T / straight No. 11
STANDARD BLADES
Diamond Knife Diamond BladeNo. 512 / straight No. 12No. 512T / straight No. 12
STANDARD BLADES
Diamond Knife Diamond BladeNo. 513 / tri-facet No. 13No. 513T / tri-facet No. 13
STANDARD BLADES
Diamond Knife Diamond BladeNo. 525 / axe No. 25No. 525T / axe No. 25
STANDARD BLADES
Diamond Knife Diamond BladeNo. 526 / triple edge vertical No. 26No. 526T / triple edge vertical No. 26
TITAN Micrometer Handle No. 500
0.171.0
45°
0.171.0
3F
0.171.5
45°
0.171.0
45° 30°
0.171.0
45°
0.171.0
30°
3F
0.171.5
45°
0.171.0
0.171.0
45°
0.171.0
30°
0.171.0
3F
0.171.0
45° 30°
0.171.0
45°
0.171.0
30°
0.171.0
3F
0.171.5
45°
45° 30°
A
A A1
A
B
B
B
B
B D
D
D
D
D
A
L
L
L
L
L
513 tri-facet 1.0 3.0 0.17 45° / 30° 13
513t tri-facet 1.0 3.0 0.1 45° / 30° 13t
axe
DIAMON D CUTTI NG I N STR U M E NTS FOR M ICROS U RG E RY
Amidia AG Telefon | Fax InternetMattenstrasse 11 +41 32 333 24 74 info@amidia.chCH-2555 Brügg +41 32 333 24 76 www.amidia.chSwitzerland
08 |
08
Page 27
0.171.0
30°
0.171.0
3F
0.171.5
45 °
0.171.0
45° 30°
• The amidia micrometer handle is made out of best quality TITAN and MEDICAL STEEL material.• Each depth of the blade can be adjusted without steps. The scale is divided each hundredth millimeter.• Available with all diamond blades you will find in our leaflets, for micrometer handle.
STANDARD BLADES
Diamond Knife Diamond BladeNo. 511 / straight No. 11No. 511T / straight No. 11
STANDARD BLADES
Diamond Knife Diamond BladeNo. 512 / straight No. 12No. 512T / straight No. 12
STANDARD BLADES
Diamond Knife Diamond BladeNo. 513 / tri-facet No. 13No. 513T / tri-facet No. 13
STANDARD BLADES
Diamond Knife Diamond BladeNo. 525 / axe No. 25No. 525T / axe No. 25
STANDARD BLADES
Diamond Knife Diamond BladeNo. 526 / triple edge vertical No. 26No. 526T / triple edge vertical No. 26
TITAN Micrometer Handle No. 500
0.171.0
45°
0.171.0
3F
0.171.5
45°
0.171.0
45° 30°
0.171.0
45°
0.171.0
30°
3F
0.171.5
45°
0.171.0
0.171.0
45°
0.171.0
30°
0.171.0
3F
0.171.0
45° 30°
0.171.0
45°
0.171.0
30°
0.171.0
3F
0.171.5
45°
45° 30°
A
A A1
A
B
B
B
B
B D
D
D
D
D
A
L
L
L
L
L
525 axe 1.4 3.0 0.17 45° 25
525t axe 1.4 3.0 0.1 45° 25t
triple edge vertical
DIAMON D CUTTI NG I N STR U M E NTS FOR M ICROS U RG E RY
Amidia AG Telefon | Fax InternetMattenstrasse 11 +41 32 333 24 74 info@amidia.chCH-2555 Brügg +41 32 333 24 76 www.amidia.chSwitzerland
08 |
08
Page 27
0.171.0
30°
0.171.0
3F
0.171.5
45 °
0.171.0
45° 30°
• The amidia micrometer handle is made out of best quality TITAN and MEDICAL STEEL material.• Each depth of the blade can be adjusted without steps. The scale is divided each hundredth millimeter.• Available with all diamond blades you will find in our leaflets, for micrometer handle.
STANDARD BLADES
Diamond Knife Diamond BladeNo. 511 / straight No. 11No. 511T / straight No. 11
STANDARD BLADES
Diamond Knife Diamond BladeNo. 512 / straight No. 12No. 512T / straight No. 12
STANDARD BLADES
Diamond Knife Diamond BladeNo. 513 / tri-facet No. 13No. 513T / tri-facet No. 13
STANDARD BLADES
Diamond Knife Diamond BladeNo. 525 / axe No. 25No. 525T / axe No. 25
STANDARD BLADES
Diamond Knife Diamond BladeNo. 526 / triple edge vertical No. 26No. 526T / triple edge vertical No. 26
TITAN Micrometer Handle No. 500
0.171.0
45°
0.171.0
3F
0.171.5
45°
0.171.0
45° 30°
0.171.0
45°
0.171.0
30°
3F
0.171.5
45°
0.171.0
0.171.0
45°
0.171.0
30°
0.171.0
3F
0.171.0
45° 30°
0.171.0
45°
0.171.0
30°
0.171.0
3F
0.171.5
45°
45° 30°
A
A A1
A
B
B
B
B
B D
D
D
D
D
A
L
L
L
L
L
526 triple edge vertical 1.0 3.0 0.17 26
526t triple edge vertical 0.8 3.0 0.1 26t
Amidia LTD Mattenstrasse 11 CH-2555 Brügg
Phone +41 32 333 24 74 Fax +41 32 333 24 76
Mail info@amidia.ch Web www.amidia.ch 15
15
20
15
25
3015
20
15
25
30
B = width / L = length / D = thickness / A = angle
Diamond cutting instruments for micro surgery
drawing article no. description B L D A blade
double edge vertical
DIAMON D CUTTI NG I N STR U M E NTS FOR M ICROS U RG E RY
Amidia AG Telefon | Fax InternetMattenstrasse 11 +41 32 333 24 74 info@amidia.chCH-2555 Brügg +41 32 333 24 76 www.amidia.chSwitzerland
08 |
08
Page 28
0.171.0
45°
0.171.0
0.171.0
45°
0.25
0.2
15°
STANDARD BLADES
Diamond Knife Diamond BladeNo. 527 / double edge vertical No. 27No. 527T / double edge vertical No. 27
STANDARD BLADES
Diamond Knife Diamond BladeNo. 528 / single edge vertical No. 28No. 528T / single edge vertical No. 28
STANDARD BLADES
Diamond Knife Diamond BladeNo. 533T / arcuate (Thornton) No. 33
STANDARD BLADES
Diamond Knife Diamond BladeNo. 566 / amidia-trak No. 66
0.171.0
45°
0.171.0
0.171.0
45°
0.25
0.2
15°
0.171.0
45°
0.171.0
45°
0.171.0
45°
0.25
0.2
0.171.0
45°
0.171.0
45°
0.171.0
0.25
0.2
15°
A
A
A
A
D
D
D
D
B
B
B
B
L
L
L
L
527 double edge vertical 1.0 3.0 0.17 45° 27
527t double edge vertical 1.0 3.0 0.1 45° 27t
single edge vertical
DIAMON D CUTTI NG I N STR U M E NTS FOR M ICROS U RG E RY
Amidia AG Telefon | Fax InternetMattenstrasse 11 +41 32 333 24 74 info@amidia.chCH-2555 Brügg +41 32 333 24 76 www.amidia.chSwitzerland
08 |
08
Page 28
0.171.0
45°
0.171.0
0.171.0
45°
0.25
0.2
15°
STANDARD BLADES
Diamond Knife Diamond BladeNo. 527 / double edge vertical No. 27No. 527T / double edge vertical No. 27
STANDARD BLADES
Diamond Knife Diamond BladeNo. 528 / single edge vertical No. 28No. 528T / single edge vertical No. 28
STANDARD BLADES
Diamond Knife Diamond BladeNo. 533T / arcuate (Thornton) No. 33
STANDARD BLADES
Diamond Knife Diamond BladeNo. 566 / amidia-trak No. 66
0.171.0
45°
0.171.0
0.171.0
45°
0.25
0.2
15°
0.171.0
45°
0.171.0
45°
0.171.0
45°
0.25
0.2
0.171.0
45°
0.171.0
45°
0.171.0
0.25
0.2
15°
A
A
A
A
D
D
D
D
B
B
B
B
L
L
L
L
528 single edge vertical 1.0 3.0 0.17 45° 28
528t single edge vertical 1.0 3.0 0.1 45° 28t
arcuate (thornton)
DIAMON D CUTTI NG I N STR U M E NTS FOR M ICROS U RG E RY
Amidia AG Telefon | Fax InternetMattenstrasse 11 +41 32 333 24 74 info@amidia.chCH-2555 Brügg +41 32 333 24 76 www.amidia.chSwitzerland
08 |
08
Page 28
0.171.0
45°
0.171.0
0.171.0
45°
0.25
0.2
15°
STANDARD BLADES
Diamond Knife Diamond BladeNo. 527 / double edge vertical No. 27No. 527T / double edge vertical No. 27
STANDARD BLADES
Diamond Knife Diamond BladeNo. 528 / single edge vertical No. 28No. 528T / single edge vertical No. 28
STANDARD BLADES
Diamond Knife Diamond BladeNo. 533T / arcuate (Thornton) No. 33
STANDARD BLADES
Diamond Knife Diamond BladeNo. 566 / amidia-trak No. 66
0.171.0
45°
0.171.0
0.171.0
45°
0.25
0.2
15°
0.171.0
45°
0.171.0
45°
0.171.0
45°
0.25
0.2
0.171.0
45°
0.171.0
45°
0.171.0
0.25
0.2
15°
A
A
A
A
D
D
D
D
B
B
B
B
L
L
L
L
533t arcuate (thornton) 1.0 3.0 0.1 15° 33t
amidia trak
DIAMON D CUTTI NG I N STR U M E NTS FOR M ICROS U RG E RY
Amidia AG Telefon | Fax InternetMattenstrasse 11 +41 32 333 24 74 info@amidia.chCH-2555 Brügg +41 32 333 24 76 www.amidia.chSwitzerland
08 |
08
Page 28
0.171.0
45°
0.171.0
0.171.0
45°
0.25
0.2
15°
STANDARD BLADES
Diamond Knife Diamond BladeNo. 527 / double edge vertical No. 27No. 527T / double edge vertical No. 27
STANDARD BLADES
Diamond Knife Diamond BladeNo. 528 / single edge vertical No. 28No. 528T / single edge vertical No. 28
STANDARD BLADES
Diamond Knife Diamond BladeNo. 533T / arcuate (Thornton) No. 33
STANDARD BLADES
Diamond Knife Diamond BladeNo. 566 / amidia-trak No. 66
0.171.0
45°
0.171.0
0.171.0
45°
0.25
0.2
15°
0.171.0
45°
0.171.0
45°
0.171.0
45°
0.25
0.2
0.171.0
45°
0.171.0
45°
0.171.0
0.25
0.2
15°
A
A
A
A
D
D
D
D
B
B
B
B
L
L
L
L
566 amidia-trak 1.0 3.0 0.17 45° 66
16
Amidia LTD Mattenstrasse 11 CH-2555 Brügg
Phone +41 32 333 24 74 Fax +41 32 333 24 76
Mail info@amidia.ch Web www.amidia.ch
Diamond cutting instruments for micro surgery
Instructions for diamond knives with a micrometerFig. 1Diamond blade retracted and protected.
Fig. 2Button has to be pushed from A to B before use.
Fig. 3Turn the micrometerdrum to position 0.The blade is now flush with the guide shoe in position 0.
Fig. 4Turn the micrometerdrum again to the requested depth setting.
Fig. 5After use, the blade can be protected by retracting the button from B to A. Theblade is now protected. The depth setting is not affected and remains the same asadjusted at Fig. 4.
Before sterilizing the knife must be in it’s original status with the blade retracted.
Button
Button
Button
Fig. 5
Fig. 4
Fig. 3
Fig. 2
Fig. 1
Amidia LTD Mattenstrasse 11 CH-2555 Brügg
Phone +41 32 333 24 74 Fax +41 32 333 24 76
Mail info@amidia.ch Web www.amidia.ch 17
B = width / L = length / D = thickness / A = angle
Diamond cutting instruments for micro surgery
Diamond knives to implant Intacs and Kera RingsThe footplate was specially designed for this procedure. The micrometer guarantees a very accura-te cutting depth.
drawing article no. description B L D blade
Amidia INTACS – KERA RINGSB
L
D 526-01 triple edge vertical 0.8 3.5 0.1 26-01
526-02 triple edge vertical 1.0 3.5 0.2 26-021
5
20
15
25
30
amidia
15
20
15
25
30
amidia
Diamond knives for retinal surgery(with a titanium handle)
drawing article no. description B L D A blade
B
DIAMON D CUTTI NG I N STR U M E NTS FOR M ICROS U RG E RY
Amidia AG Telefon | Fax InternetMattenstrasse 11 +41 32 333 24 74 info@amidia.chCH-2555 Brügg +41 32 333 24 76 www.amidia.chSwitzerland
08 |
08
Page 20
TITAN Retina Handle No. 300
• The amidia retina handle is made out of TITAN bayonet and used predominantly for Glaucoma surgery.• Available with all diamond blades you will find in our leaflets, for retina handle.• We also manufacture to client specifications.
STANDARD BLADES
Diamond Knife Diamond BladeNo. 301 / NEW retina straight No. 01
STANDARD BLADES
Diamond Knife Diamond BladeNo. 302 / NEW retina straight No. 02
0.170.9
45°
0.170.5
20°
0.170.9
45°
A
B D
L
301R retina straight 0.5 3.0 0.17 20° 01
302R retina straight 0.9 3.0 0.17 45° 02
311R retina straight 1.0 3.0 0.17 45° 11
18
Amidia LTD Mattenstrasse 11 CH-2555 Brügg
Phone +41 32 333 24 74 Fax +41 32 333 24 76
Mail info@amidia.ch Web www.amidia.ch
B = width / L = length / D = thickness / A = angle
Diamond cutting instruments for micro surgery
Step diamond knivesAvailable with all diamond blades you will find in our leaflets for seven step handle.
drawing article no. description B L D A/A1 blade
straight
DIAMON D CUTTI NG I N STR U M E NTS FOR M ICROS U RG E RY
Amidia AG Telefon | Fax InternetMattenstrasse 11 +41 32 333 24 74 info@amidia.chCH-2555 Brügg +41 32 333 24 76 www.amidia.chSwitzerland
08 |
08
Page 32
TITAN Seven-Step Handle No. 800
90°
60°
0.11.0
3F
0.171.0
45°
0.17width
0.17width
°
• The amidia seven-step handle is made out of best quality TITAN and MEDICAL STEEL material.• Available with all diamond blades and different depths you will find in our leaflets, for seven-step handle.
STANDARD BLADES
Diamond Knife Diamond BladeNo. 811 / straight, depth at 0/0.3/0.4/0.5/0.6/0.8/1.0/2.5 mm No. 11
STANDARD BLADES
Diamond Knife Diamond BladeNo. 813 / tri-facet, depth at 0/0.3/0.4/0.5/0.6/0.8/1.0/2.5 mm No. 13
STANDARD BLADES
Diamond Knife Diamond BladeNo. 827 / double edge vertical, depth at 0/0.3/0.4/0.5/0.6/0.8/1.0/2.5 mm No. 27
PHACO BLADES
Diamond Knife Diamond BladeNo. 822 / spear with blunt sides, width 3.0 mm No. 22No. 823 / spear with blunt sides, width 3.2 mm No. 23
PHACO BLADES
Diamond Knife Diamond BladeNo. 885 / lance with blunt sides, width 3.0 mm No. 85No. 821 / lance with blunt sides, width 3.2 mm No. 21
90°
60°
3F
0.171.0
45°
0.17width
0.17width
90°
60°
3F
0.17width
0.17width
60°
7
3F
0.171.0
45°
7width
°
7
°
3F
0.171.0
45°
°
A
A1A
A
A
A
B
B
B
B
B D
D
D
D
D
L
L
L
L
L
811 straight for right handed 1.0 3.0 0.17 45° 11
811-01 straight for left handed 1.0 3.0 0.17 45° 11-01
steps at 0/0.3/0.4/0.5/0.6/0.8/1.0/2.5 mm
tri-facet
DIAMON D CUTTI NG I N STR U M E NTS FOR M ICROS U RG E RY
Amidia AG Telefon | Fax InternetMattenstrasse 11 +41 32 333 24 74 info@amidia.chCH-2555 Brügg +41 32 333 24 76 www.amidia.chSwitzerland
08 |
08
Page 32
TITAN Seven-Step Handle No. 800
90°
60°
0.11.0
3F
0.171.0
45°
0.17width
0.17width
°
• The amidia seven-step handle is made out of best quality TITAN and MEDICAL STEEL material.• Available with all diamond blades and different depths you will find in our leaflets, for seven-step handle.
STANDARD BLADES
Diamond Knife Diamond BladeNo. 811 / straight, depth at 0/0.3/0.4/0.5/0.6/0.8/1.0/2.5 mm No. 11
STANDARD BLADES
Diamond Knife Diamond BladeNo. 813 / tri-facet, depth at 0/0.3/0.4/0.5/0.6/0.8/1.0/2.5 mm No. 13
STANDARD BLADES
Diamond Knife Diamond BladeNo. 827 / double edge vertical, depth at 0/0.3/0.4/0.5/0.6/0.8/1.0/2.5 mm No. 27
PHACO BLADES
Diamond Knife Diamond BladeNo. 822 / spear with blunt sides, width 3.0 mm No. 22No. 823 / spear with blunt sides, width 3.2 mm No. 23
PHACO BLADES
Diamond Knife Diamond BladeNo. 885 / lance with blunt sides, width 3.0 mm No. 85No. 821 / lance with blunt sides, width 3.2 mm No. 21
90°
60°
3F
0.171.0
45°
0.17width
0.17width
90°
60°
3F
0.17width
0.17width
60°
7
3F
0.171.0
45°
7width
°
7
°
3F
0.171.0
45°
°
A
A1A
A
A
A
B
B
B
B
B D
D
D
D
D
L
L
L
L
L
813 tri-facet 1.0 3.0 0.17 45° / 30° 13
steps at 0/0.3/0.4/0.5/0.6/0.8/1.0/2.5 mm
double edge vertical
DIAMON D CUTTI NG I N STR U M E NTS FOR M ICROS U RG E RY
Amidia AG Telefon | Fax InternetMattenstrasse 11 +41 32 333 24 74 info@amidia.chCH-2555 Brügg +41 32 333 24 76 www.amidia.chSwitzerland
08 |
08
Page 32
TITAN Seven-Step Handle No. 800
90°
60°
0.11.0
3F
0.171.0
45°
0.17width
0.17width
°
• The amidia seven-step handle is made out of best quality TITAN and MEDICAL STEEL material.• Available with all diamond blades and different depths you will find in our leaflets, for seven-step handle.
STANDARD BLADES
Diamond Knife Diamond BladeNo. 811 / straight, depth at 0/0.3/0.4/0.5/0.6/0.8/1.0/2.5 mm No. 11
STANDARD BLADES
Diamond Knife Diamond BladeNo. 813 / tri-facet, depth at 0/0.3/0.4/0.5/0.6/0.8/1.0/2.5 mm No. 13
STANDARD BLADES
Diamond Knife Diamond BladeNo. 827 / double edge vertical, depth at 0/0.3/0.4/0.5/0.6/0.8/1.0/2.5 mm No. 27
PHACO BLADES
Diamond Knife Diamond BladeNo. 822 / spear with blunt sides, width 3.0 mm No. 22No. 823 / spear with blunt sides, width 3.2 mm No. 23
PHACO BLADES
Diamond Knife Diamond BladeNo. 885 / lance with blunt sides, width 3.0 mm No. 85No. 821 / lance with blunt sides, width 3.2 mm No. 21
90°
60°
3F
0.171.0
45°
0.17width
0.17width
90°
60°
3F
0.17width
0.17width
60°
7
3F
0.171.0
45°
7width
°
7
°
3F
0.171.0
45°
°
A
A1A
A
A
A
B
B
B
B
B D
D
D
D
D
L
L
L
L
L
827 double edge vertical 1.0 3.0 0.17 45° 27
steps at 0/0.3/0.4/0.5/0.6/0.8/1.0/2.5 mm
spear
DIAMON D CUTTI NG I N STR U M E NTS FOR M ICROS U RG E RY
Amidia AG Telefon | Fax InternetMattenstrasse 11 +41 32 333 24 74 info@amidia.chCH-2555 Brügg +41 32 333 24 76 www.amidia.chSwitzerland
08 |
08
Page 32
TITAN Seven-Step Handle No. 800
90°
60°
0.11.0
3F
0.171.0
45°
0.17width
0.17width
°
• The amidia seven-step handle is made out of best quality TITAN and MEDICAL STEEL material.• Available with all diamond blades and different depths you will find in our leaflets, for seven-step handle.
STANDARD BLADES
Diamond Knife Diamond BladeNo. 811 / straight, depth at 0/0.3/0.4/0.5/0.6/0.8/1.0/2.5 mm No. 11
STANDARD BLADES
Diamond Knife Diamond BladeNo. 813 / tri-facet, depth at 0/0.3/0.4/0.5/0.6/0.8/1.0/2.5 mm No. 13
STANDARD BLADES
Diamond Knife Diamond BladeNo. 827 / double edge vertical, depth at 0/0.3/0.4/0.5/0.6/0.8/1.0/2.5 mm No. 27
PHACO BLADES
Diamond Knife Diamond BladeNo. 822 / spear with blunt sides, width 3.0 mm No. 22No. 823 / spear with blunt sides, width 3.2 mm No. 23
PHACO BLADES
Diamond Knife Diamond BladeNo. 885 / lance with blunt sides, width 3.0 mm No. 85No. 821 / lance with blunt sides, width 3.2 mm No. 21
90°
60°
3F
0.171.0
45°
0.17width
0.17width
90°
60°
3F
0.17width
0.17width
60°
7
3F
0.171.0
45°
7width
°
7
°
3F
0.171.0
45°
°
A
A1A
A
A
A
B
B
B
B
B D
D
D
D
D
L
L
L
L
L
822 spear with blunt sides 3.0 4.0 0.17 90° 22
823 spear with blunt sides 3.2 4.0 0.17 90° 23
steps at 0.15/0.2/0.25/0.3/0.37/0.5/4.0 mm
other steps available as per customers request
0
0.60
0.65
0.70
0
0.60
0.65
0.70
0 .80
1.002.50
0 .80
1.002.50
Amidia LTD Mattenstrasse 11 CH-2555 Brügg
Phone +41 32 333 24 74 Fax +41 32 333 24 76
Mail info@amidia.ch Web www.amidia.ch 19
0 .50
4.000
0 .50
4.000
B = width / L = length / D = thickness / A = angle
Diamond cutting instruments for micro surgery
drawing article no. description B L D A blade
clear cornea 60°DIAMON D CUTTI NG I N STR U M E NTS FOR M ICROS U RG E RY
Amidia AG Telefon | Fax InternetMattenstrasse 11 +41 32 333 24 74 info@amidia.chCH-2555 Brügg +41 32 333 24 76 www.amidia.chSwitzerland
08 |
08
Page 33
CLEAR CORNEA BLADES
Diamond Knife Diamond BladeNo. 898 / clear cornea with sharp sides, width 2.5 mm No. 98No. 895 / clear cornea with sharp sides, width 2.6 mm No. 95No. 877 / clear cornea with sharp sides, width 2.8 mm No. 77No. 873 / clear cornea with sharp sides, width 3.0 mm No. 73No. 874 / clear cornea with sharp sides, width 3.2 mm No. 74
60°
0.172.65
40°
0.171.0
0.2
0.17width
A
B D
L
897 clear cornea with sharp sides 3.0 4.0 0.17 60° 97
834 clear cornea with sharp sides 3.2 4.0 0.17 60° 34
steps at 0/0.25/0.3/0.35/0.4/1.0/2.5/5.0 mm
clear cornea 90°898 clear cornea with sharp sides 2.5 3.5 0.17 90° 98
895 clear cornea with sharp sides 2.6 3.5 0.17 90° 95
877 clear cornea with sharp sides 2.8 3.5 0.17 90° 77
873 clear cornea with sharp sides 3.0 3.5 0.17 90° 73
874 clear cornea with sharp sides 3.2 3.5 0.17 90° 74
steps at 0/0.15/0.2/0.25/0.3/0.37/0.5/4.0 mm
Glaucoma B B1 L D A blade
A
B
L
D
B1 820-01 1.0 0.3 3.5 0.17 25° 20-01
steps at 0.15/0.2/0.25/0.3/0.37/0.5/4.0 mm
one step handle tri-facet
A
B
L
D
309-F tri-facet, depth at 0.3 1.0 0.17 60° 09
one step handle straight
A
B
L
D
315-F right-handed straight, depth at 0.3
0.7 0.17 45° 15
315-01F left-handed straight, depth at 0.3
0.7 0.17 45° 15
other steps available as per customers request
Step diamond knives
20
Amidia LTD Mattenstrasse 11 CH-2555 Brügg
Phone +41 32 333 24 74 Fax +41 32 333 24 76
Mail info@amidia.ch Web www.amidia.ch
B = width / L = length / D = thickness / A = angle
Diamond cutting instruments for micro surgery
Black diamond knives• Better visualization Non-glare surface• Consistent, predictable & superior
diamond edge incision• Reduced acquisition cost • Reduced repair cost• available in a titanium or
a peek handle
drawing angled holderstraight holder description B1/B L D A blade
lance
A
L
DB
CVD-1010-A CVD-1010 lance 1.0 4.0 0.20 75° 1010
CVD-1012-A CVD-1012 lance 1.2 4.0 0.20 75° 1012
CVD-1014-A CVD-1014 lance 1.4 4.0 0.20 75° 1014
trapezoid
B
B1
L
D
A
CVD-1175-A CVD-1175 tapered spear 1.5-1.8 4.0 0.20 90° 1175
CVD-1177-A CVD-1177 tapered spear 1.8-2.4 4.0 0.20 90° 1177
CVD-1179-A CVD-1179 tapered spear 1.8-2.75 4.0 0.20 90° 1179
CVD-1180-A CVD-1180 tapered spear 2.5-2.8 4.0 0.20 90° 1180
CVD-1182-A CVD-1182 tapered spear 2.65-3.0 4.0 0.20 90° 1182
CVD-1183-A CVD-1183 tapered spear 2.8-3.0 4.0 0.20 90° 1183
CVD-1185-A CVD-1185 tapered spear 2.5-3.5 4.0 0.20 90° 1185
CVD-1186-A CVD-1186 tapered spear 3.2-3.5 4.0 0.20 90° 1186
Amidia LTD Mattenstrasse 11 CH-2555 Brügg
Phone +41 32 333 24 74 Fax +41 32 333 24 76
Mail info@amidia.ch Web www.amidia.ch 21
B = width / L = length / D = thickness / A = angle
Diamond cutting instruments for micro surgery
drawing angled holderstraight holder description B L D A blade
spear 2 sides sharp
A
L
DB
CVD-1120-A CVD-1120 spear 2.8 4.0 0.20 90° 1120
CVD-1123-A CVD-1123 spear 3.0 4.0 0.20 90° 1123
CVD-1125-A CVD-1125 spear 3.2 4.0 0.20 90° 1125
clear cornea - 4 sides sharp
B
L
D
A
CVD-1146-A CVD-1146 spear vc 1.8 4.0 0.20 90° 1146
CVD-1150-A CVD-1150 spear vc 2.2 4.0 0.20 90° 1150
CVD-1152-A CVD-1152 spear vc 2.4 4.0 0.20 90° 1152
CVD-1154-A CVD-1154 spear vc 2.5 4.0 0.20 90° 1154
CVD-1158-A CVD-1158 spear vc 2.65 4.0 0.20 90° 1158
CVD-1160-A CVD-1160 spear vc 2.8 4.0 0.20 90° 1160
CVD-1162-A CVD-1162 spear vc 3.0 4.0 0.20 90° 1162
CVD-1164-A CVD-1164 spear vc 3.2 4.0 0.20 90° 1164
crescent
B
L
D
CVD-1205-A CVD-1205 9-edge vertical 1.4 4.0 0.20 1205
CVD-1210-A CVD-1210 9-edge vertical 2.0 4.0 0.20 1210
Black diamond knives• Better visualization• Non-glare surface• Consistent, predictable & superior diamond edge incision• Reduced acquisition cost • Reduced repair cost• available in a titanium or
a peek handle
22
Amidia LTD Mattenstrasse 11 CH-2555 Brügg
Phone +41 32 333 24 74 Fax +41 32 333 24 76
Mail info@amidia.ch Web www.amidia.ch
amidia
amidia
15°
15°
B = width / L = length / D = thickness / A = angle
Diamond cutting instruments for micro surgery
Diamond knives for micro surgeryThe amidia micro surgery handles are available with a straight or angled holder.
drawing article no. description B L D A blade
angled straight
DIAMON D CUTTI NG I N STR U M E NTS FOR M ICROS U RG E RY
Amidia AG Telefon | Fax InternetMattenstrasse 11 +41 32 333 24 74 info@amidia.chCH-2555 Brügg +41 32 333 24 76 www.amidia.chSwitzerland
08 |
08
Page 35
TITAN Neuro Handle No. N200
°
°
• Superior performance, unmatched precision • For more information, contact us today!
STANDARD BLADES
Diamond Knife Diamond BladeNo. N267 / straight, 45˚ single sided, 1.0 x 0.17 x 6 mm No. 67
STANDARD BLADES
Diamond Knife Diamond BladeNo. N268 / Lance 60˚ single sided, 1.0 x 0.17 . 6 mm No. 68
STANDARD BLADES
Diamond Knife Diamond BladeNo. N269 / round 7 facets, single sided, 1.0 x 0.17 x 6 mm No. 69
SPECIAL BLADES
Diamond Knife Diamond BladeNo. N281 / special straight, 60˚, 1.45 x 0.17 x 1.8 mm No. 81
°
°
A
A
A
B
B
B
B D
D
D
D
L
L
L
N250A N250 straight, single sided 1.0 3.0 0.17 30° 50
N267A N267 straight, single sided 1.0 3.0 0.17 45° 67
lance
DIAMON D CUTTI NG I N STR U M E NTS FOR M ICROS U RG E RY
Amidia AG Telefon | Fax InternetMattenstrasse 11 +41 32 333 24 74 info@amidia.chCH-2555 Brügg +41 32 333 24 76 www.amidia.chSwitzerland
08 |
08
Page 35
TITAN Neuro Handle No. N200
°
°
• Superior performance, unmatched precision • For more information, contact us today!
STANDARD BLADES
Diamond Knife Diamond BladeNo. N267 / straight, 45˚ single sided, 1.0 x 0.17 x 6 mm No. 67
STANDARD BLADES
Diamond Knife Diamond BladeNo. N268 / Lance 60˚ single sided, 1.0 x 0.17 . 6 mm No. 68
STANDARD BLADES
Diamond Knife Diamond BladeNo. N269 / round 7 facets, single sided, 1.0 x 0.17 x 6 mm No. 69
SPECIAL BLADES
Diamond Knife Diamond BladeNo. N281 / special straight, 60˚, 1.45 x 0.17 x 1.8 mm No. 81
°
°
A
A
A
B
B
B
B D
D
D
D
L
L
L
N268A N268 lance, single sided 1.0 3.0 0.17 60° 68
N251A N251 lance, single sided 1.4 3.0 0.17 60° 51
round
D
L
B
N269A N269 round 7 facets single sided 1.0 4.0 0.17 69
special
A
DB
N281 triple edge vertical 1.5 1.8 0.17 60° 81
amidia
amidia
Amidia LTD Mattenstrasse 11 CH-2555 Brügg
Phone +41 32 333 24 74 Fax +41 32 333 24 76
Mail info@amidia.ch Web www.amidia.ch 23
0
0
0.30
DURA
0
0
0.30
DURA
B = width / L = length / D = thickness / A = angle
Diamond cutting instruments for micro surgery
Diamond knife for micro surgery• Easy and fast cutting thanks to the extremely sharp diamond blade
• The precisely adjustable cutting depth allows a safe procedure
• Consistent cutting capabilities even after years of use
• Handle made of titanium and surface coated in high vacuum
drawing article no. description B L D bladeD B
L
N269-01 micro surgery 1.4 4.0 0.2 69-01
0.30
DURA
24
Amidia LTD Mattenstrasse 11 CH-2555 Brügg
Phone +41 32 333 24 74 Fax +41 32 333 24 76
Mail info@amidia.ch Web www.amidia.ch
B = width / L = length / D = thickness / A = angle
Diamond cutting instruments for micro surgery
Zeppelin diamond knives for micro surgeryFor extremly delicate micro-incisions and dissections. The cutting edges are distinguished by their superb sharpness.
drawing article no. description B L D A blade
A L
DB
PDD 011lance diamond knife, straight sharp, slightly upward angled tip 15° working/total length 50 mm/170 mm
1.40 3.0 0.17 60° A-51
PDD 111lance diamond knife, straight sharp, slightly upward angled tip 15° working/total length 100 mm/220 mm
1.40 3.0 0.17 60° A-51
A
DB
PDD 112triple edge vertical diamond knife, straight, tip blunt, 90° angled working total length 100 mm/220 mm
1.40 0.17 60° A-81
PDD 113triple edge vertical diamond knife, straight, tip sharp, 90° angled working total length 100 mm/220 mm
1.40 0.17 60° A-81
To order please contact Zeppelin Medical Instruments GmbH (marketer according to RL93/42EWG)Mozartstrasse 3A-6850 Dornbirn / Austria
phone +43 (0) 5572 25677fax +43 (0) 5572 25679e-mail office@zeppelin-medical.comwebsite www.zeppelin-medical.com
Amidia LTD Mattenstrasse 11 CH-2555 Brügg
Phone +41 32 333 24 74 Fax +41 32 333 24 76
Mail info@amidia.ch Web www.amidia.ch 25
B = width / L = length / D = thickness / A = angle
Diamond cutting instruments for micro surgery
drawing article no. description B L D A blade
A L
DB
PDD 211lance diamond knife, straight sharp, slightly upward angled tip 15° working/total length 120 mm/240 mm
1.40 3.0 0.17 60° A-51
A L
DB
PDD 311lance diamond knife, straight sharp, slightly upward angled tip 15° working/total length 100 mm/220 mm
1.40 3.0 0.17 60° A-51
PDD 411lance diamond knife, straight sharp, slightly upward angled tip 15° working/total length 120 mm/240 mm
1.40 3.0 0.17 60° A-51
PDD 511lance diamond knife, straight sharp, slightly upward angled tip 15° working/total length 140 mm/260 mm
1.40 3.0 0.17 60° A-51
To order please contact Zeppelin Medical Instruments GmbH (marketer according to RL93/42EWG)Mozartstrasse 3A-6850 Dornbirn / Austria
phone +43 (0) 5572 25677fax +43 (0) 5572 25679e-mail office@zeppelin-medical.comwebsite www.zeppelin-medical.com
26
Amidia LTD Mattenstrasse 11 CH-2555 Brügg
Phone +41 32 333 24 74 Fax +41 32 333 24 76
Mail info@amidia.ch Web www.amidia.ch
3.0
5.0
#15
#11
B = width / L = length / D = thickness / A = angle
Diamond cutting instruments for micro surgery
Cosmetic diamond knives for plastic surgeryCosmetic scalpels are much sharper than steel blades and they keep their sharpness even after many procedures. This enables the surgeon to have the highest precision and the cleanest cut available. Incisions with diamond scalpels are easier to make; wounds heal better and faster.
article no. CVD-1310-Titan
article no. CVD-1320-Titan
Amidia LTD Mattenstrasse 11 CH-2555 Brügg
Phone +41 32 333 24 74 Fax +41 32 333 24 76
Mail info@amidia.ch Web www.amidia.ch 27
0.30
0.40
0.30
0.40
0.3
0.4
0.6
0.5
51
0
0.5
1.5
51
0
0.5
1.5
51
0
0.5
1.5
5
0.5
1.5
5
0.5
1.5
Diamond cutting instruments for micro surgery
cleaning sticks
Amidia cleaning sticks to remove the particles from the blade9014 1 set of cleaning sticks (5 pieces of styropor)
measuring gauge600 measuring gauge type RK
Accessories
600
28
Amidia LTD Mattenstrasse 11 CH-2555 Brügg
Phone +41 32 333 24 74 Fax +41 32 333 24 76
Mail info@amidia.ch Web www.amidia.chVersion 05 August 10.2015
Diamond cutting instruments for micro surgery
Legend to SymbolsManufacturer Article Number unsterile Directions for use to consider
Attention CE Class I CE Class Im
DescriptionDiamond scalpels are reusable instruments, consisting of a handle and a diamond blade. The blades are made from natural or synthetic diamond and measure between 100μm and 200μm thick; the handles are made from titanium.
ApplicationsDiamond scalpels are designed for various eye operations.
Precautions• Read instructions before use• Diamond scalpels are not sterile and must be sterilised.• Diamond scalpels must be handed to surgeons with the blade retracted and handed back by them with the blade in the same
position. They must not be placed opened on the instrument tray.
Instructions for use• Diamond scalpels must be thoroughly cleaned and sterilised before use. Diamond scalpels must also be cleaned and then
sterilised after every subsequent use. For instructions on how to clean and sterilise diamond scalpels please refer to the section entitled Cleaning and Sterilisation.
• The diamond blades must never come into contact with other instruments. Special care must therefore be taken during surgical operations, to ensure that the blades do not come into contact with instruments such as forceps/tweezers or sharp surgical instruments.
• Ensure that diamond blades are not damaged before use. Damaged diamond scalpels should not be used. The blades can be re-sharpened.
• After every use of a diamond scalpel, care must be taken to ensure that the blade is pulled back into the handle, using the pressure or bayonet mechanism.
CleaningImmediately after using a diamond scalpel, the blade must be rinsed with water using a 20ml spray, preventing cell particles or visco-elastic materials from sticking to the blade. Dirt on the titanium handle can be removed using a small soft brush. Care must be taken to ensure that the blade has been retracted into the handle.
Manual cleaning The following cleaning process has been approved in accordance with the ASTM standard test method E 2314-03 (with a germ reduction rate of up to 410). The manufacturer recommends manual cleaning.• Immediately after use, the blade must be rinsed with water using a 20ml syringe• The diamond scalpel must be placed in an alkaline cleaning solution (pH ≥ 10) for at least 12 minutes at 55°C. The cleaner
“Mediclean Forte” of Dr. Weigert is validated.• The diamond scalpel must then be neutralised for 2 minutes in citric acid and then washed for at least 2 minutes in running
water (3l/min).
Machine cleaningIn accordance with the recommendations of RKI, diamond scalpels must be cleaned in a washing machine designed for micro- surgical instruments. The manufacturer’s instructions should be followed. This is not a procedure validated by the diamond scalpel manufacturer.
Note: The diamond blades must never come into contact with other instruments; otherwise there is a risk that the blades will be damaged. Great care must therefore be taken when loading washing machines.
Directions for useAmidia diamond scalpels
1250
REF NON STERILE
!
Amidia LTD Mattenstrasse 11 CH-2555 Brügg
Phone +41 32 333 24 74 Fax +41 32 333 24 76
Mail info@amidia.ch Web www.amidia.ch 29Version 05 August 10.2015
Diamond cutting instruments for micro surgery
After cleaning, the condition of the instrument must be checked. Following this, the diamond scalpel must be immediately placed in the sterilisation box or in another suitable container.
Diamond scalpels can also be cleaned using ultra-sound cleaning systems.
Sterilisation• Diamond scalpels must be sterilised before each use.• Diamond scalpels must be sterilised with the diamond blades retracted. Please therefore ensure that the blade has been
pushed back into the titanium handle.• Sterilisation filters must be fitted with protective materials (cushioned mats).
Sterilisation method Type of sterilisation Item loaded Temperature Sterilisation time in minutes
Steam Centrifugal cycle packaged 134ºC (270ºF) 18.0
Flash process Centrifugal cycle not packaged 134ºC (270ºF) 4.0
Steam Flash cycle packaged 134ºC (270ºF) 4.0
Flash process Flash cycle not packaged 134ºC (270ºF) 18.0
The above specifications meet the industry standards for steam sterilisation cycles. Since there are variations in different steam sterilisation systems and the levels of germs on instruments in clinical use vary greatly, Amidia LTD cannot provide any specific data to guarantee an appropriate level of sterilisation. Every hospital must check the correct procedures for guaranteeing a proper level of sterilisation. Please refer to the current ANSI/AAMI standards on hospital procedures for steam sterilisation and sterilisation guarantees or the hospital’s own procedures for the most suitable specifications.
For steam sterilisation, please refer to ANSI/AAMI standards and recommended practice volume 1: Sterilisation, ST46-1993, Section 5.8.
For flash processes, please refer to ANSI/AAMI standards for “Good Hospital Practice”: Flash Sterilization – Steam sterilisation for “Patient care items for immediate use”. ST37-1996, Section 5.4
We recommend that packaged diamond scalpels should be steam sterilised at 270°F (134°) either in a centrifugal cycle for 18 minutes or in a flash cycle for 18 minutes.
Note:• Diamond blades are made from an extremely hard but sensitive material. Handle these ultra-sharp blades carefully to avoid damage. • Mechanical contact must be prevented.• Diamond scalpels must be cleaned and sterilised before each use.• After use the blade must be immediately retracted into the titanium handle.• When used correctly, diamond scalpels can withstand several hundred cleaning and sterilisation cycles.• Diamond scalpels must never be stored un-cleaned.
Diamond scalpels (RK-Blades) with a micrometer (A500 – 599)Setting the micrometer dial:
1. Diamond blade retracted and protected.2. Button has to be pushed from A to B before use.3. Turn the micrometerdrum to position 0. The blade is now flush with the guide shoe in position 0.4. Turn the micrometerdrum again to the requested depth setting.5. After use, the blade can be protected by retracting the button from B to A. The blade is now protected. The depth setting is
not affected and remains the same as adjusted at 4. ðsee instruction with pictures on page 16.
We recommend that the cutting depth should be checked. The cutting depth can be measured using an A-600 (device).
Maintenance / GuaranteeWe suggest sending diamond knives for an inspection to our company at least after 500 surgeries.Amidia LTD provides a 3-year guarantee for all mechanical components, on condition that the scalpels are used correctly with the titanium handle.
Proper DisposalThe country specific laws and regulations have to be observed for proper disposal.
Manufacturer:Amidia LTD, Mattenstrasse 11, CH-2555 Brügg, Switzerland, Phone +41 32 333 24 74 • Fax +41 32 333 24 76
30
Amidia LTD Mattenstrasse 11 CH-2555 Brügg
Phone +41 32 333 24 74 Fax +41 32 333 24 76
Mail info@amidia.ch Web www.amidia.ch
Diamond cutting instruments for micro surgery
We conducted a retrospective study of 12,182 consecutive patients who underwent clear corneal phacoemulsifiction, comparing incision technologies.
Group AIn 3,912 patients the main and sideport incisions were created with diamonds.
Group BIn 8,270 patients standard metal keratomes were employed for both incisions.
All patients were seen within 8 hours of surgery. There were no postoperative wound leaks (0/3,912) at any point in time with a mean first visit postoperative pressure of 19.2 mm Hg in Group A.
There were 9/8,270 (p<0.05) wound leaks with a mean first visit postoperative pressure of 21.6 mm Hg (p<0.05) in Group B. All 9 wound leaks in Group B were from the sideport. 3/9 wound leaks required suturing. 6/9 wound leaks sealed spontaneously.The intraocular pressure difference reflected the need to hydrate the wounds more in Group B as they were more difficult to seal and the eyes were left with a higher intraocular pressure at the end of the case. 180/3,912 (4.55%) of patients in Group A had an early IOP spike greater than 28 mm Hg versus 842/8,270 (10.18%) in Group B (p<0.05). None of the patients in either group experienced an endophthalmitis or vascular occlusion.
We found that the use of diamonds for the incision significantly reduced the rate of wound leaks and the amount of wound hydration resulting in lower early postoperative IOP’s and potentially dangerous IOP spikes.
Christoph Kranemann, MD
Why diamonds are better than disposable blades
Amidia LTD Mattenstrasse 11 CH-2555 Brügg
Phone +41 32 333 24 74 Fax +41 32 333 24 76
Mail info@amidia.ch Web www.amidia.ch 31
Diamond cutting instruments for micro surgery
Most of our diamond blades can be resharpened several times if they are not too badly damaged.
For each repair, the handle is totally dismantled, and all of the mechanical parts are cleaned, checked and replaced if necessary. Micrometer and step knives are recalibrated.
After regrinding, the diamond blade is as good as a new blade.
We accept other knives for repair except the micrometer knives. However, we can not accept responsabi lity for the break-age of blades other than Amidia.
We always do our best in order to return your repairs as soon as possible. However, the lead time may be variable due to the many different kind of blade types we receive for resharpening.
Customer service
For more information about our service, please contact your distributor or Amidia.
Amidia LTD Mattenstrasse 11 CH-2555 Brügg
phone +41 32 333 24 74 fax +41 32 333 24 76
mail info@amidia.ch web www.amidia.ch
Recommended