View
234
Download
0
Category
Preview:
Citation preview
TD3 QuickStart Guide
Solutions for the Digital Evidence Lifecycle™
Device Connection Diagram
Step-by-Step Installation
Forensic Duplicator
Guidance SoftwareW223 N608 Saratoga DriveWaukesha, WI 53186Toll Free: 1 (866) 973-6577Main: 1 (626) 229-9191www.tableau.com
©2012 Guidance Software, Inc. All Rights Reserved. EnCase and Guidance Software are registered trademarks or trademarks owned by Guidance
Software in the United States and other jurisdictions and may not be used without prior written permission. All other marks and brands may be claimed as
the property of their respective owners. Updated 11-2012.
SD Card TP4 Power Supply
top
Modular Expansion Connector
left-side
4
Cable Recommendations
Note: Expansion modules are built for direct connection to TD3 via the Modular Expansion Connector
IDE Drive Power
IDE Signal
Unified SAS Signal & Drive Power
SCSI Drive Power
SCSI Signal
SAS, SCSI & IDE Module
1394B (FireWire 800)
USB 3.0
SATA Signal
SATA Drive Power
Ethernet
USB 2.0/1.1
Storage Enclosure
SATA to SATA Extension Cable
TC2-8-R2
TC6-8
TC4-8-R2
TC2-8-R2
TC10-8
TDPX4, TDPX5, TDPX6
TC7-9-9
TC-USB3
TC3-8
TC5-8-R2
TC8 or TC-USB3
TDS1 (direct connect)
TC3-22-18
1a
1b
2a/2b
3a
3b
4
5
6
7a
7b
8
9
10a
10b
WriteBlocked
YES
YES
YES
YES
YES
YES
Duplicate Disk-to-Disk Disk-to-FileHashVerify MD-5 & SHA-1HPA/DCO DisableBlank Check Source Management Destination
FormatWipe Single Pass Multiple PassLogsSettings System Settings Duplication Settings User Profile
TD3 Menu Options
USB 3.0 SATA Drive PowerFireWire
5 6 7a 7b
bottom
Gigabit Ethernet
USB 2.0
SATA (Data/Power)
TDS198 10a 10b
right-side
4
1a
1b
2a
2b
3a
3b
5 6 7a 7b
9
8
10a
10b
SD Card TD3 Operating System TP4 Power Supply
TDS1 Storage Enclosure
TDPX4 (SCSI)1
TDPX5 (IDE)
TDPX6 (SAS)
TD3 is a modular forensic imaging system using a touch-screen graphical user interface (UI). A comprehensive discussion of all TD3 features and functions, along with detailed product setup instructions is available in the TD3 User’s Guide. This document can be downloaded at: www.tableau.com/library.
Press and release the membrane ON/OFF switch to cycle power to TD3. Once powered ON, normal use and control of the TD3 is via the touch-screen UI. Light finger taps and swipes on the UI are all that is required to use this product. Where user data entry is required, a touch-screen keyboard will be displayed.
The following basic sequence assumes that the user has installed a 3.5 inch SATA hard-drive in the TDS1 SATA storage enclosure:
1. Following instructions shown on the TDS1 label, slide the TD3 from left to right to mate TD3 with the TDS1 enclosure.
2. Connect the TP4 power supply to the TD3 DC power-in connection.
3. For forensic imaging, SATA, USB or FireWire storage devices can be directly connected to the main TD3 unit.
4. For forensic imaging of SCSI1, IDE, or SAS storage devices, the appropriate TDPX expansion module must be used.
To connect, set an expansion module in the keyed slots on top of the TDS1, and slide left to right until mated to the TD3 expansion connector.
To remove expansion module, power down TD3, grasp and hold TD3 main imager unit,
depress connector lock, and slide expansion module right to left.
5. Upon initial startup: First, follow on-screen instructions to create a TD3 administrator password. Next, navigate to the ‘Settings’ menu option to setup and configure your TD3 with personal preferences. Please refer to the TD3 User’s Guide for comprehensive setup instructions.
6. Upon subsequent use, the main menu is displayed for user selection; scroll and tap the function icon to select the desired action. Many functions have user-selectable options; please refer to the TD3 User’s Guide for details.
7. Always remember to power down TD3 when changing source device, or when swapping expansion modules.
Device Connection Diagram
Recommended