View
17
Download
0
Category
Preview:
Citation preview
LUXMATE Devices
Daylight Control ler LM-TLXRelay Control ler LM-RLX
The new daylight controller:Easy to plan, easy to install and always easy to use
305 mm wide, 252 mm long and 56
mm high. From the outside the LM-
TLX device is rather inconspicuous.
But inside, is intelligent technology
that simplifies the work of planners,
fitters and building owners. A small
box for daylight control that fulfils
three wishes at once and creates an
optimal work environment for people.
- Flexibility in planning, since commis-
sioning is implemented over a bus
and addressing the lighting and
modules can therefore be adapted
to existing needs
- Simplicity in installation, since the
connection is made without tools
and saves time
- Intelligence for the future, since the
usage of the room can change at
any time
The World of LUXMATEwith LM-TLX and LM-RLX
Operate
Visualize
Communicate with outside
systems
Building Management Level
Monitor
Check
Maintain
Issue permissions
Operate
Daylight
Artificial light
Field Level
Blind
Window
Indoor climate
Emergency light
Daylight
Blind
Dynamics
Time
Automation Level
Indoor climate
Super-room
Burning hours
Emergency light
Remote maintenance
daylight dependentdimming with LM-TLX
Luminaire 1
Luminaire 2
Luminaire 3
Bus/Mains
Momentary action switches
Luminaire 4
Luminaire 5
Luminaire 6
Luminaire 7
LM-RLX
Luminaire 8 (with emergenc
Application example: Store room without windowsLow-cost switching of the artificial light with LM-RLX
and non dimmable operating modules (conventional
ballasts, standard electronic ballasts)
switching thelight withLM-RLX
Pre-installed luminai-
res are connected to
the LM-TLX module
without tools by means
of the plug&play procedure,
saving time and avoiding mistakes.
The well thought-out installation
method enables the "satellite
system" to be expanded easily at any
time.
With a height of 56 mm
the LM-TLX module is
the lowest of its kind.
This is of great benefit
when fitting in false ceilings
because there is no shortage of space
due to other installations. Connection
sockets on the side add to this advan-
tage. As a result, the LM-TLX module
can also be fitted into extremely nar-
row false ceilings.
The LM-TLX module
is functional as soon
as it has been connec-
ted. Addressing can
also be implemented over
the bus after installation and after
closure of the ceiling panels. In this
way it is possible to reconfigure the
lights and other devices at any time,
without additional cables and without
having to open the ceiling panels.
This applies not only for setting the
scenes and the daylight dependence,
but also for the addressing after
room borders or workplaces and fur-
niture have been relocated or repla-
ced.
LM-TLX is reallynarrow
LM-TLX is fastand ready
LM-TLX is reallysmart
cy light)
Luminaire 1
Luminaire 2
Luminaire 3
LM momentary action switch LM momentary action switch
Luminaire 4
LSD
PST PSTLuminaire 5
Luminaire 7
Luminaire 8
Luminaire 9
LM-TLX
Luminaire 6 (with emergency light)
Application example: Open-plan office with windowsDaylight dependent dimming with LM-TLX and digital
dimmable ballasts (PCA)
Everything under controlThe LM-TLX is installed complete in
the hollow space inside a false ceiling
and addressed over a bus line. The
module can also be addressed and
configured at a later time without
tools and without rewiring. A single
LM-TLX can control 9 pairs of lumi-
naires individually over the various
LUXMATE control units. Furthermore,
pre-defined scenes can be recalled at
any time and adjusted manually. 3
arbitrary scenes can compensate
automatically for the daylight. Opera-
tion is through the user locally.
Good light is completely naturalModern offices and administration
buildings are characterized by a high
level of flexibility. Whether open-plan
or individual office, the room archi-
tecture changes and so do the requi-
rements of the people working there.
It is particularly important that the
lighting should be able to adapt to
changing situations. With the LM-TLX,
LUXMATE delivers the appropriate
solution.
The daylight controller enables the
amount of artificial light to be adap-
ted to the existing daylight in order
that it conforms with the individual
requirements of the user. Moreover,
additional LUXMATE modules enable
other room functions, e.g. blinds or
air-conditioner, to be tuned to one
another, regulated and aligned on
what the user is currently doing. The
result is an optimal environment in
the room, which is stimulating and
which increases people's well-being.
A further benefit provided by the
LUXMATE light and room manage-
ment system is energy optimization
of the building. Adaptation of the
artificial light to the available amo-
unt of daylight leads to considerable
savings in energy. All this takes place
in the background, imperceptibly for
the user but with maximum advanta-
ge for humans and their well-being.
The LM-TLX is installed in the hollow spaceinside a false ceiling. The module can then beaddressed and configured at any time over abus, without tools and without rewiring.
Everything inside, everything supplied:Daylight controller LM-TLX
Text for Invitation of TendersElectronic module with bus connection
for controlling artificial light. Intended
for separate control of up to 9 pairs of
luminaires using "quick-install" connec-
tion technology; 2 of these outputs for
controlling luminaires with emergency
light contact unit; 5 direct RJ-45
connections of which 1 for a light sen-
sor, 2 for local momentary action swit-
ches and 2 for presence sensors. New
addressing, re-addressing and configu-
ration possible without access to the
LM-TLX module. Flat, galvanized, pain-
ted steel case, with all electrical connec-
tions at the sides. Installation by means
of fixing angle (supplied), suitable for
direct or suspended fixing.
Equivalent to LUXMATE
Type Article Number
LM-TLX 22115147
Planning Instructions-Luminaire connections: The luminai-
res must be prepared for dimmable
digital ballasts (PCA), electronic
transformers (TEL) and phase dim-
mers (PHD). Cable length (power
line and DSI jointly in one cable):
max. 15 m. The luminaire connec-
ting cables must be fitted by the
manufacturer or on site with Wie-
land connectors (Type GST 18i5S S1
ZR1).
-Connections for presence sensors
PST: Cable length max. 10 m. Care
must be taken during assembly that
the cable is attached to the correct
pins of the 8-pole RJ-45 connector.
-Connections for momentary action
switches with 4-pole RJ-45 connec-
tor; max. cable length 10 m.
-Power line / bus connection with
Wieland female part (Type GST
18i5S B1 ZR1).
-Light sensor LSD: Connection over
4-pole RJ-45 connector: max. cable
length 250 m; install according to
fitting instructions. As an alternati-
ve to several light sensors, especial-
ly in larger buildings, an external
daylight sensor on the roof can be
used over the LUXMATE bus
together with a LUXMATE room
automation computer.
-Distributor box: The distributor box
must be provided by the building
owner for wiring the LM-TLX modu-
les in "satellite cabling".
-Additional LUXMATE modules, e.g.
LM-IRB, can be connected at the
RJ-45 connection Line out/Bus out.
This connection must not be used
for further LM-TLX modules.
-The LM-TLX must be counted once
for calculating the bus power supply
(LM-BV, LM-BVS35), and 9 times for
the database of the LUXMATE room
automation computer LRA-1500(x).
Function / ApplicationThe daylight controller LM-TLX is used
in open-plan offices and adjacent indi-
vidual offices or in large rooms in
which the emphasis is on the use of
natural light, the saving of energy, and
ergonomic aspects such as the well-
being of the persons using the room.
The LM-TLX enables the artificial light
to be controlled according to the
amount of daylight entering the room.
0 % 25 % 50 %
Daylight Artificiallight
500 lx
NotesAll luminaires are connected by means of
connectors directly with the box, which is instal-
led on the ceiling. This must be taken into
account when using the LM-TLX in countries
where this kind of installation is not usual.
InstallationThe LM-TLX is screwed to the ceiling
using the fixing brackets supplied.
Dimensions305 x 252 x 56 mm (without fixing angle
and connector)
Case materialSteel plate, galvanized and painted
orange (RAL 2008 matt)
Weightapprox 2500 g
32
3
2
3
3
2
2
3
2
3
3
3
2
3
3
2
2
2
2
32
2
2 233 23 23 23
Mains
alternativ
Infrared input moduleLM-IRB
Infrared sensorIRED
Infrared control unitIRS
Double momentaryaction switch
(24V SELV)
Light sensorLSD
PresencesensorPST
max. 2 PCA (PHD, TEL)
max. 2 PCA (TEL, PHD)
max. 2 PHD (TEL, PCA)
For additional LUXMATE equip-ment, not for through-connec-tion of further LM-TLXes
max. 2 PCA (PHD, TEL)
ma
x. 2
TE
L (
PC
A,
PH
D)
ma
x. 2
PC
A (
PH
D,
TE
L)
ma
x. 2
PC
A (
PH
D,
TE
L)
Em
erg
en
cy l
igh
t co
nta
ct u
nit
Em
erg
en
cy l
igh
t co
nta
ct u
nit
LUXMATE-BUS
Nominal voltage230/240 V~, 50/60 Hz
Permissible input voltage198...264 V~, 50...60 Hz
Power loss< 8 W
Inputs2 double momentary action switches (24V
SELV)
1 light sensor LSD
(2 x 1,5 mm2; max. 250 m)
LUXMATE-Bus
2 movement sensors PST
(12V supply through LM-TLX)
MiscellaneousStatus LED for displaying operating status
Addressing1 room, group, own address per luminaire
output
1 separate address for LSD
1 room, group address per double momen-
tary action switch together with 1 presence
sensor each
Control range0; 1 - 100% (rel. lighting intensity)
ModeCOMMON (all)
INTENS (brightness)
Outputs9 luminaire outputs (power and DSI) for lumi-
naires with max. 2 lamp control modules
(PCA, PHD, TEL), of which 2 outputs also for
luminaires with independently powered
emergency light contact units.
Power line/bus for additional LUXMATE
modules (max. 100W)
Permissible ambient temperature0...50 °C
Degree of protection / protection classIP 20
SKI (earth connection)
305 mm
252
56 mm
For unrestricted switchingRelay controller LM-RLX
Text for Invitation of TendersElectronic module with bus connection
for controlling artificial light. Intended
for separate control of up to 9 luminai-
re outputs with a maximum connected
load of 250W per luminaire output using
"quick-install" connection technology; 2
of these outputs for controlling luminai-
res with emergency light contact unit; 6
direct RJ-45 connections of which 2 for
local double momentary action swit-
ches, 2 for emergency light sensors and
2 for presence sensors. New addressing
and re-addressing possible without
access to the LM-RLX module. Flat, gal-
vanized, painted steel case, with all
electrical connections at the sides.
Installation by means of fixing angle
(supplied), suitable for direct or suspen-
ded fixing.
Equivalent to LUXMATE
Type Article Number
LM-RLX 22154049
Planning Instructions-Luminaire connections: The luminai-
res must be must be fitted with ope-
rating modules suitable for swit-
ching lamps up to 230/250V a.c. The
luminaire connecting cables must
be fitted by the manufacturer or on
site with Wieland connectors.
-Connections for presence sensors
PST: Cable length max. 10 m. Care
must be taken during assembly that
the cable is attached to the correct
pins of the 8-pole RJ-45 connector.
-Connections for momentary action
switches and emergency light sen-
sors with 4-pole RJ-45 connector;
max. cable length 10 m.
-Power line / bus connection with
Wieland female part.
-Distributor box: The distributor box
must be provided by the building
owner for wiring the LM-RLX modu-
les in "satellite cabling".
-Additional LUXMATE modules, e.g.
LM-IRB, can be connected at the
RJ-45 connection Line out/Bus out.
This connection must not be used
for further LM-RLX modules (Type
GST 18i5S B1 ZR1).
-The LM-RLX module must be coun-
ted once for calculating the bus
power supply (LM-BV, LM-BVS35),
and 9 times for the database of the
LUXMATE room automation compu-
ter LRA-1500(x).
Function / ApplicationThe relay controller LM-RLX is used
in open-plan offices and adjacent
individual offices or in large rooms in
which the emphasis is on economy.
The LM-RLX enables the artificial
light to be controlled according to
whether anyone is in the room. The
emergency light function is also
integrated in the concept.
32
3
3
3
3
3
3
3
3
3
32
3
2
23 2333
3
3
NotesAll luminaires are connected by means of
connectors directly with the box, which is
installed on the ceiling. This must be taken into
account when using the LM-RLX in countries
where this kind of installation is not usual.
InstallationThe LM-TLX is screwed to the ceiling using
the fixing brackets supplied.
Dimensions270x245x54
Case materialSteel plate, galvanized and painted
Weightapprox 2500 g
Mains
alternativ
Infrared input moduleLM-IRB
Infrared sensorIRED
Infrared control unit IRS
Double momentaryaction switch(24VSELV)
Emergencylight sensor
Presencesensor PST
EVG (PC PRO), KVG
HV tungsten halogen lamp
HV tungsten halogen lamp
For additional LUXMATE equip-ment, not for through-connectionof further LM-RLXes
EVG (PC PRO), KVG
Em
erg
en
cy l
igh
t co
nta
ct u
nit
Em
erg
en
cy l
igh
t co
nta
ct u
nit
LUXMATE-BUS
Nominal voltage230/240V~, 50/60Hz
Permissible input voltage207...264V~, 50...60Hz
Power loss< 8W
Inputs2 double momentary action switches (24V
SELV)
2 emergency light sensors LUXMATE bus
2 movement sensors PST (12V supply
through LM-RLX)
MiscellaneousStatus LED for displaying operating status
Adressing1 room, group, own address per luminaire
output address
1 room, group address per double momen-
tary contact switch together with 1 presence
sensor each
ModeCOMMON (all)
INTENS (brightness)
Outputs9 luminaire switching outputs (power line)
for luminaires with max. 250W per luminaire
output, of which 2 outputs also for luminaires
with independently powered emergency light
contact units.
Power line/bus for additional LUXMATE
modules (max. 100W)
Permissible ambient temperature0...50°C
Degree of protection / protection classIP 20
SKI (earth connection)
LRA-LUXMATE Room Automation
PCSI
245 mm
270
mm
54 mm
Up to now, general lighting and
safety lighting have been regarded as
separate systems and have therefore
been realized separately. The LM-TLX
and LM-RLX enable the safety
lighting to be integrated into the
LUXMATE system, exploiting syner-
gies in control and monitoring which
would otherwise be unused. A number
of different solutions are possible for
emergency lighting, depending on the
layout of the LUXMATE facility.
Simple implementationIn the simple implementation, two
luminaires with integrated emergency
light contact units are connected to
each of two outputs of the LM-TLX.
From a suitable location, the emer-
gency luminaires are switched to
emergency light operation over the
LUXMATE bus. The outlay for wiring
is considerably reduced.
Convenient implementationIn the most convenient implementati-
on, a light sensor is installed for each
emergency lamp, directed towards
the lamp. By means of evaluation
electronics, the light sensor value is
supplied to a corresponding momen-
tary action switch input of the LM-
TLX, this input having been configu-
red in a customer-specific way. The
visualization, control and monitoring
requires that the emergency light
software LMW-ELM is installed on a
separate LUXMATE server or on the
LUXMATE room automation computer
LRA.
The benefits for the customer:
- Automatic or manual initiation ofthe function test and operatingtime test
- Monitoring of the emergency lightelectronics, rechargeable batteryand lamp (failure, aging)
- Documentation of the emergencylight test
Light Management and SafetyLighting Combined
The light sensor LSD measures the daylight
entering the room through the window. The
connected LM-TLX module uses this value for
controlling the room lighting. Installation and
planning instructions must be followed exactly
in order to ensure proper
functioning of the daylight dependent control-
ler.
GST 18i 5-pole 250/400V, 16 A with screw
connection for conductors 1.5 - 2.5 mm2, single
wire and finely stranded, one connection per
pole, unmounted with strain relief, for cable
with diam. 9.8 - 12.5 mm.
Insulation removal length: 8 mm
Sheath removal length: 46 mm
Der Anwesenheitssensor PST ist optimiert für El
The presence sensor PST has been optimized for
office applications and can be connected direct-
ly to the LM-TLX or LM-RLX module. At an
installation height of 3m, the slightest move-
ments are detected reliably within a recording
area of 4m x 4m.
The unit can be recessed into the ceiling, semi-
recessed in a box, or surface mounted. The line
length from PST to LM-TLX or LM-RLX must not
exceed 10 m.
The infrared input module LM-IRB receives the
signals of the infrared control unit IRS over the
IR sensors IRED and converts these into LUX-
MATE bus signals. One LM-IRB can convert the
infrared signals of up to 2 differently configured
infrared remote controllers. The IR remote con-
troller enables three different scenes to be pro-
grammed and recalled in the room. In addition,
LUXMATE outputs can be separately switched
and dimmed in up to 5 domains.
The infrared sensor IRED for ceiling installation
converts the signals from the infrared remote
controller IRS into electrical signals and sends
these on to the LM-IRB.
Up to 9 different IR channels can be set at the
IRS. The IRS can basically be used to operate
any kind of LUXMATE output, e.g. also blinds or
screens.
Type Article Number
Control spot for recalling three scenes and for
controlling brightness and glare protection,
white and neutrally imprinted “1”, “2” and “3”
for general applications
Accessories for LM-TLX y LM-RLX
Presence sensor PST
IRS
IRED
LM-IRB
Infrared control unit
Light sensor LSD (only for LM-TLX)
Wieland connector
Circle control point
Type Article Number
LSD 20731906
IRS 20975492
IRED 22114587
IRB 22114219
Type Article Number
PST 22153900
for LM-TLX:
TLX BU 5 POL 22153929
TLX ST 5 POL 22153928
for LM-RLX: on request
Type Article Number
Type Article Number
LM-CSW (white 1,2,3) 22154211
LM-CSG (grey 1, 2, 3) 22154212
LM-CSS (silver 1, 2, 3) 22154213
LM-CSM (brass 1, 2, 3) 22154214
other icons on request
Te
chn
ical
alt
era
tio
ns
rese
rve
d.
Art
.-N
r. 2
2.15
4.04
2
04/
2004
- E
© L
UX
MA
TE
Co
ntr
ols
Gm
bH
INTERNATIONALLUXMATE Controls GmbHSchmelzhuetterstrasse 26A-6850 Dornbirn/AustriaTel. +43–(0)5572–599–0Fax +43–(0)5572–599–699luxmate@luxmate.co.atwww.luxmate.com
GREAT BRRITAINLUXMATE LimitedThomas HouseHampshire International Business ParkCrockford Lane, ChinehamBasingstoke RG24 8WHTel. +44–(0)1256–7075-70Fax +44–(0)1256–7075-65luxmate@uk.luxmate.co.atwww.luxmate.com
SPAINLUXMATE S.L.C/ Isla de Hierro n–° 5Polígoni Industrial NorteSan Sebastián de los Reyes E-28700 MadridTel. +34–(0)91–659 30 76Fax +34–(0)91–653 03 74luxmate@luxmate.eswww.luxmate.com
Presented by:
Recommended