Coupling · 2021. 8. 10. · Tested: IEC 62561-2 Application: Protect the of ground rod wile...

Copper-Bonded Ground Rod is made by molecularlybonding pure electrolytic copper onto a low carbon,high tensile steel core with exceeding 0.254 mm(254 micron) thick. To ensure in safety and quality,it meets standard for grounding and bonding equipments.

Tested: IEC 62561-2Application: Protect the of ground rod wile drivingMaterial: High Tensite Steel

Copper-BondedGround Rod-Standard Type

Driving Head

Electrolytic Grounding is made of 54 mm(2-1/8,,) OD diameter or type K copper pipewhich natural chemical electrolytic salt canbe refilled. Exothermic welding is used forconnecting condructor to the copper pipe.

Electrolytic Grounding(KEG)

Kumwell MEG is an alternate solution forEffectively by modifying the soil surroundingthe electrode. In practically, to achieve thedesired reduction in ground resistance by adding more grid conductors or ground rods is often impossible. Soil Treatment is an effectivesolution to decrease ground resistance whichis utilized to an advantage in poor conductivearea such as rocky soil.

More E�ective Grounding(MEG)

Tested: IEC 62561-1Application: Clamp ground rod with copper tape conductorMaterial: Copper Alloy - BS EN 1982 Bolt-Brass

Rod Copper Tape Clamp

Application: Lead the ground rod into the hard soil areaMaterial: High Tensite Steel

Tip

Solid Copper and Stainless steel GroundRods are used in Critical soil applicationwhich has a pH value below 3 or more 8.

Ground Rod Solid Copper/ Stainless Steel

Copper-Bonded Ground Rod is made by molecularlybonding pure electrolytic copper onto a low carbon,high tensile steel core with exceeding 0.254 mm(254 micron) thick. To ensure in safety and quality,it meets UL standard for grounding and bonding equipments.

Copper-BondedGround Rod-Threaded Type

Tested: IEC 62561-2Application: Extend to the length of ground rodMaterial: High Strength silicon Bronze

Coupling

Tested: IEC 62561-1Application: Clamp ground rod with copper conductorMaterial: Copper Alloy - BS EN 1982 Bolt-Brass

Rod Cable Clamp

Tested: IEC 62561-1Application: Clamp pipe parallel to one cableMaterial: Copper Alloy - BS EN 1982 U Bolt, Nut-Brass

Pipe to Cable Clamp

Tested: IEC 62561-1Application: Fix copper tape conductor with steel flat sufaceMaterial: Copper Alloy - BS EN 1982, Bolt/Nut:Brass Aluminium Alloy -BS EN 2898, Bolt/Nut: Stainless Steel

Tape Clamp

Tested: IEC 62561-4Application: Lock wire or cable conductor on flat surfaceMaterial: Copper Alloy - BS EN 1982 Aluminium Alloy -BS 2898

Ground Clamp

Application: Fix conductor on earth pointMaterial: Copper Alloy - BS EN 1982

Front Cover

Tested: IEC 62561-1Application: Clamp cable conductors to steel pipeMaterial: Copper Alloy - BS EN 1982 U Bolt, Nut-Brass

One Cable to Pipe Clamp

Tested: IEC 62561-1Application: Clamp Solid copper conductor to large metal pipeMaterial: Copper Alloy - BS EN 1982 Copper Tape - BS EN 13601 Bolt, Nut-Brass

Pipe Bond Clamp

Tested: IEC 62561-1Application: Clamp rod to cable lug conductorMaterial: Copper Alloy - BS EN 1982 Bolt, Nut-Brass

Rod To Cable Lug Clamp

Tested: IEC 62561-1Application: Clamp rod parallel to copper tape conductorMaterial: Copper Alloy - BS EN 1982 U Bolt, Nut-Brass

U Bolt Rod Clamp

Tested: IEC 62561-1Application: Support air terminal to connect with copper stranded, solid or tape conductors.Material: Copper Alloy - BS EN 1982

Flat Saddle

Tested: IEC 62561-4Application: Fix copper stranded or solid cinductorsMaterial: Copper Alloy - BS EN 1982, Bolt-Brass Aluminium Alloy - BS 2898, Bolt-Stainless Steel

Cable Support

Tested: IEC 62561-1Application: Connect copper stranded or solid conductorsMaterial: Copper Alloy - BS EN 1982, Bolt-Brass Aluminium Alloy - BS 2898, Bolt- Stainless Steel

Cable Cross Clamp

Tested: IEC 62561-4Application: Fix copper or aluminium tape conductorsMaterial: Copper Alloy - BS EN 1982, Bolt-Brass Aluminium Alloy-BS 2898, Bolt-Stainless Steel

Tape Support

Tested: IEC 62561-1Application: Support air terminal to connect with copper stranded, solid or tape conductors.Material: Copper Alloy - BS EN 1982

Ridge Saddle

Tested: IEC 62561-1Application: Support air terminal to connect with copper stranded, or solid conductors.Material: Copper Alloy - BS EN 1982, Bolt-Brass

Double Base Saddle