View
226
Download
0
Category
Preview:
Citation preview
NACE International
CCoorrrroossiioonn CCoonnffeerreennccee aanndd EExxppoo
CCoorrrroossiioonn 22000088
March 16-20, 2008 New Orleans, Louisiana, USA
Volume 1 of 9
Printed from e-media with permission by: Curran Associates, Inc.
57 Morehouse Lane Red Hook, NY 12571
www.proceedings.com
ISBN: 978-1-60560-981-2 Some format issues inherent in the e-media version may also appear in this print version.
Copyright© (2008) by NACE International All rights reserved. For permission requests, please contact NACE International at the address below.
NACE International P.O. Box 41027 Houston, Texas 77241-1027 PHONE: 800 797 6223 FAX: 290 228 6251 www.nace.org
TABLE OF CONTENTS
Volume 1
08001 - Determine Usable Coating Systems - Results of Laboratory Tests Versus Long Term Trials in Nature.........................................................................................................................................1
G.J. Binder
08002 - Degradation Study of Polymer Coating: Improvement in Coating Weatherability Testing and Coating Failure Prediction ..........................................................................................................15
François-Xavier Perrin, Celine Merlatti, Emmanuel Aragon, André Margaillan
08003 - Correlation of Accelerated Corrosion Testing with Natural Exposure After 6+ Years in a Coastal Environment .....................................................................................................................................33
Darren Ward
08004 - Non-Destructive Determination of Rust Creep .................................................................................42C. Weinell, S.N. Rasmussen
08005 - Cathodic Disbonding of Epoxy Coatings - Effect of Test Parameters.............................................52Ole Øystein Knudsen, Jan Ivar Skar
08007 - The Effect of Anode Isolation Methods on Coating Cathodic Disbondment ..................................67A. Al-Borno, M. Brown, S. Rao
08008 - A Method for the Evaluation of Wet Surface Tolerant Coatings ....................................................77F. Gui, D. Hill, C. S. Brossia
08009 - Topcoat Flaking - A Mechanism Study. Part 1: Laboratory Testing - Internal Stress, Mechanical Properties, Adhesion and Ageing ....................................................................................93
Sten B. Axelsen, Torstein Rossland, Roy Johnsen, Ole Øystein Knudsen
08011 - Effect of Flash Rust on Protective Properties of Organic Coatings...............................................107Gyeong Rae Kim, Tae Sung Kang, Yeon Ho Cho, Jong Man Han
08015 - Waterborne Coatings - Results of 6 Years Offshore Testing .........................................................120Jan Ivar Skar, Per Lunde
08017 - Specifications vs. Reality for Selection of Protective Coatings.......................................................134G.R.Ruschau, M.B.Surkein, R.H. Rogers
08018 - Zinc Metal Free Primer .....................................................................................................................142Neil Wilds
08019 - Measurement of Leachable Chloride Content from Coatings Applied to Stainless Steel............151David Waddell
08020 - Technical Aspects of Soluble Salt Contamination Analysis in New Shipbuilding Yards ............160C. H. Lee, S. M. Son, C. S. Shin, Y. H. Baek, K. K. Baek
08022 - Optimization of Application Procedure for Non-Skid Coating Materials in Offshore Structure ..........................................................................................................................................173
Chung Seo Park, Mong Kyu Chung, Eun Ha Song, Kwang Ki Baek, Eul Soo Chung
08024 - Coatings Strategy for Fuel Storage and Energy Facilities in Mexico ............................................187L. M. Martinez de la Escalera, M. Paredes, A. Rios, J.A. Lopez-Mendez, J. Genesca, J.A. Ascencio, L. Martinez-Gomez
08025 - Adhesion and Corrosion Performance of Nanostructured Nickel and Cobalt-based Coatings............................................................................................................................................................196
A. M. Sherik, H. Ajwad, A. H. Rasheed, A. Jabran, R. G. Ortiguerra
08027 - Insights Into Atlas Cell Testing for Selection of Linings for Oil and Gas Production Vessels and Tanks ...........................................................................................................................................210
L.S. Gray, N. deVarennes, B. Bloor, M. O'Donoghue, R. Graham, R. Garrett, V. Datta, B. Franke
08029 - Corrosion Testing of Fluorocoatings for Oil/Gas Production Tubing...........................................235L.W. McKeen, R. Albert, J. Hofmans
08032 - Corrosion and Mechanical Properties of Diamond-like Carbon Films Deposited Inside Carbon Steel Pipes ...............................................................................................................................244
B. Boardman, K. Boinapally, T. Casserly, M. Gupta, C. Dornfest, D. Upadhyaya, Y. Cao, M. Oppus
08034 - Comparison of Polysiloxane Two-coat Systems vs. a Traditional Three Coat System As External Paint Systems Over Steel for Canadian Applications ................................................255
A. Al-Borno, M. Brown, S. Rao
08036 - Evaluation of Steel and TSA Coating in a Corrosion Under Insulation (CUI) Environment ....................................................................................................................................................267
R. Kane, M. Chauviere, K. Chustz
08037 - Review of Epoxy Polymer Thermal Aging Behavior Relevant to Fusion Bonded Epoxy Coatings................................................................................................................................................287
D. Kirkpatrick, F. Aguirre, G. Jacob
08039 - Evaluation of Anticorrosion Coatings for High Temperature Service..........................................299M. Batallas, P. Singh
08040 - New Technology Helps Develop Coatings for High Operating Temperature Pipelines ..............315J.A. Kehr, S. Attaguile, M. Smith, M. Perez
08044 - External Pipeline Coating Performance Evaluation .......................................................................339M.A. Saleem, A.A. Hulaibi
08048 - Novel Poly (Phthalazinone Ether Sulfone Ketone) Heat Resistant Coating .................................348Qingling Yan, Hongyuan Chen, Yiling Zhang, Jinyun Zhao, Xigao Jian
08050 - Permanent Reference Half Cells - Part 2: Polarization Tests ........................................................353Telma Villela, Hosam Abdel-Rehim, Mauricio Guerrante, Joao H. Oliver
08051 - Evaluation of Sacrificial Anode Backfill Material ..........................................................................362O. Abuazza, R. Elaish, K. Enawaa, S. Alomami, A. Gaderbuh
08052 - Flow-induced Corrosion of Al-Zn-Mg Galvanic Anodes in Seawater...........................................381M.C. Quevedo, J. Genesca
08053 - Effectiveness of Aluminum Anodes for Cathodic Protection in Low Chloride Environments ..................................................................................................................................................394
F. Bolzoni, G. Contreras, L. Lazzari, A. Benedetti, E. Pérez
08054 - Evaluation of 100 mV Development/ Decay Criteria on 4 Meter Diameter Prestressed Concrete Cylinder Pipeline ........................................................................................................406
R. M. Elaish, O. A. Abuazza, K. Enawaa
08055 - Can Zinc Prevent Corrosion of Pre-Stressed Concrete Cylinder Pipes in High Resistivity Soils? ..............................................................................................................................................417
F.A. Garman
08058 - Prevention of External (Soil Side) Corrosion on Storage Tank Bottom Plates by Cathodic Protection System ...........................................................................................................................424
B. Chatterjee
08059 - Current and Potential Distribution Modelling for Cathodic Protection of Tank Bottoms .........433B. Bazzoni
08060 - Pipeline Integrity Automation ..........................................................................................................452D. Southern
08061 - Trials and Experiences in Wireless Automated Pipeline Rectifier Monitoring............................458L. Decker, J. Knoblach, J.C. Kitchin
08062 - Study on Pipeline Interference from Stray Current of DC Light Railway ...................................468Changfang Wu, Lingli Liu, Hongyuan Chen
08063 - Light Rail Transit Stray Current Control: How Much Water Line Protection is Really Needed? ................................................................................................................................................473
D. Lindemuth, D. Kroon
08064 - CP Criteria Assessment in the Presence of AC Interference .........................................................491M. Ormellese, L. Lazzari, S. Goidanich, V. Sesia
08066 - Determining the Compatibility of High Strength Steels to Cathodic Protection..........................501M. Billingham, G. John
08068 - Electrochemical Analysis of Pipeline CP Criteria...........................................................................515E. Ondak, F. Rizzo
08069 - 5,000 Km Row CP Survey Analysis and the Potential Advantages of the 100 mV Polarization Criterion for the CP of Aged Coating Oil and Gas Pipelines in Gulf and North of Mexico ..........................................................................................................................................................529
J. Canto, L. M. Martinez de la Escalera, H. Rivera, A. Godoy, C.G. Lopez Andrade, E.R. Betancourt, H.C. Albaya, N. Pesce, J.A. Ascencio, L. Martinez-Gomez
08070 - Plpe-to-Soil Potential Measurements, the Basic Science.................................................................537L.A. Bash
08071 - Design and Construction of the Hybrid CP System for the Mexico City Airport Jet Fuel Pipeline Under the 100mV Polarization Criterion...............................................................................557
J. Canto, L. M. Martinez de la Escalera, H. Carrillo, A. Rios, H.C. Albaya, N. Pesce, J.A. Ascencio, L. Martinez-Gomez
08072 - The Use of the 100 mV Polarization Criterion in Cathodically Protected Facilities ....................567W. Trimble
08073 - Advanced Scale Control Technology for Cooling Water Systems .................................................572C. Sui, G. Geiger
08077 - A New Multi-Functional Corrosion and Scale Inhibitor ................................................................585David Wilson
08080 - Optimizing and Improving Biocide Performance in Water Treatment Systems .........................598T.M. Williams
08081 - Corrosion of Copper Braze Alloys in Sulfide-Containing Water ..................................................616Y-M. Wang, D. Sigler
08084 - A New High Strength Corrosion Resistant Alloy for Oil and Gas Applications ..........................634S. Mannan, S. Patel
08085 - High Performance Corrosion Resistant Stainless Steels and Nickel Alloys for Oil & Gas Applications..............................................................................................................................................644
D. Aberle, D.C. Agarwal
08086 - Balance of Alloying Elements in Wear Resistant Co-based Alloys for Oil Drilling Applications .....................................................................................................................................................661
M. Yao, J. Wu
08089 - Material Selection for Turnaround Wells an Evaluation of the Impact Upon Downhole Materials When Mixing Produced Water and Seawater ...........................................................673
L. Scoppio, P.I. Nice
08090 - Performance of Selected Corrosion Resistant Alloys Under Simulated Seawater Injection Conditions Downhole......................................................................................................................691
R.D. Mack, J. Carminati
08091 - Performance of CRAs for Pressure Gauges in Sour Environments ..............................................700Rolf Bloecher, Guenter Schmitt
08095 - Resistance of Dissimilar Joints Between Steel and Nickel Alloys to Hydrogen-Assisted Cracking...........................................................................................................................................................714
M.F. Gibbs
Volume 2
08096 - Influence of Impact Angles on Penetration Rates of CRAs Exposed to a High Velocity Multiphase Flow ...............................................................................................................................733
J. Haberl, G. Mori, M. Oberndorfer, W. Havlik, P. Hosemann, M. Hawley, J.G. Swadener
08098 - Downhole CRA Materials Performance - Failure Analysis of a Sub Surface Safety Valve ........753J. Marsh
08099 - Evaluation of SSC Resistance of "Sweet" Materials in H2S Environments for Development of Ballot Guidelines in MR0175/ISO 15156 ...........................................................................766
R.D. Kane, P. Quiroga
08100 - Intergranular Stress Corrosion Cracking Susceptibility and Precipitation Behavior on Grain Boundary by Post Weld Heat Treatment of Super Martensitic Stainless Steels .......................780
Hisashi Amaya, Akira Taniyama, Kazuhiro Ogawa, Masakatsu Ueda
08102 - Electrochemical Behavior of Low C - 13% Cr Weld Joints by Using Solution Flow Type Micro-Droplet Cell ................................................................................................................................794
S. Hashizume, T. Nakayama, M. Sakairi, K. Fushimi
08104 - A Review of Laboratory Evaluation Procedures for Materials Selection in Downhole Applications - Considerations in a Fitness-for-service Evaluation for Resistance to Environmentally Assisted Cracking..........................................................................................................809
Robert Mack
08107 - Sulfide Fracture Toughness of Low-alloy Steel OCTG in Mild Conditions at Room Temperature and 40º F ...................................................................................................................................822
D. Sponseller, T. Sponseller, B. urband, G. Prideco
08108 - Interpreting and Using the NACE Double Cantilever Beam (DCB) Test .....................................856K.E. Szklarz
08109 - Effect of NACE TM0284 Test Modifications on the HIC Performance of Large-Diameter Pipes .................................................................................................................................................................871
C. Bosch, T. Haase, A. Liessem, J.P. Jansen
08110 - Hydrogen Induced Cracking (HIC) - Laboratory Testing Assessment of Low Alloy Steel Linepipe ..................................................................................................................................................884
J. Kittel, J.W. Martin, T. Cassagne, C. Bosch
08111 - Evaluation of Hydrogen Embrittlement Induced Damages in Steels Using Acoustic Emission ...........................................................................................................................................................904
V. Smanio, T. Cassagne, F. Ropital, J. Kittel, M. Fregonese, B. Normand
08113 - New Deformable Austempered Ductile Irons (DADI) as an Efficient Material for Substitution of Critical Parts of Oil Well Equipment Made from Quality Steel .......................................918
E.R. Kutelia, N.Z. Khidasheli, G.V. Beradze, T.A. Dzigrashvili, D.S. Butskhrikidze, A.M. Qafarov, A.Kh. Janahmadov, Yu.N. Hasanov, S.I. Bakhtiyarov
08115 - Development of a C125 High Strength Low Alloy Steel for OCTG: SSC Mapping in Slightly Sour Environment.........................................................................................................................930
H. Marchebois, M. Piette, L. Ladeuille, D. Senegas-Rouviere, C. Bosch, J. Pleschiutschnig, J. Leyer, B. Orlans-Joliet, E. Lepine, F. Legay, C. Linne, A. Figueiredo
08118 - Analysis & Interpretation of CIS Data ............................................................................................948R.L. Pawson
08120 - Corrosion of Natural Gas Transmission Line - A Case Study .......................................................962J. Shaikh, Z.K. Muhideen
08123 - Is Your Pipeline Corroding? .............................................................................................................975Peter Nicholson
08124 - Some Experiences and Consideration on Application of CIPS Test Technology .........................990C. Wu, D. Liu
08125 - CIS Interpretation for ECDA - A Technical Analysis ....................................................................995Mark Yunovich
08126 - CIS Study and Interference Root Cause Analysis of an Early External Corrosion Leakage of a Production Gas Pipeline in the Gas Fields in Northeast Mexico ........................................1009
J. Canto, H. Rivera, N. Pesce, J.A. Ascencio, L. Martinez-Gomez, H.C. Albaya, J.L. Baez, R. Perez-Polanco, A. Alanis
08128 - Improving the Success of DG-ICDA Projects................................................................................1016S.F. Biagiotti Jr., J. Fox
08129 - Overall Mechanisms of High pH and Near-Neutral pH SCC, Models for Forecasting SCC Susceptible Locations, and Simple Algorithms for Predicting High pH SCC Crack Growth Rates ............................................................................................................................1029
Fengmei Song
08130 - Internal Corrosion Direct Assessment of Buried Steel Pipeline in Chinese Oil Industry..........1062L. Qimin, H. Guibai
08131 - Facilitating Internal Corrosion Direct Assessment Using Advanced Flow and Corrosion Prediction Models .......................................................................................................................1067
V.V. Lagad, S. srinivasan, R.D. Kane
08135 - Integrity Management for Piggable and Non-Piggable Subsea Pipelines ...................................1077Daniel Powell
08136 - Validation of External Corrosion Direct Assessment with Inline Inspection in Gas Transmission Pipeline ...................................................................................................................................1098
YoungGeun Kim, DeokSoo Won, HongSeok Song
08137 - Flow Modeling to Optimize Wet Gas Pipeline Water Management............................................1106F. Carimalo, I. Fouche, R. Hauguel, X. Campaignolle, T. Chretien, M. Meyer
08138 - Water Accumulation Assessment in Wet Gas Pipelines ...............................................................1122F. Carimalo, I. Fouche, R. Hauguel, X. Campaignolle, T. Chretien, M. Meyer
08139 - In-Plant Piping Hydrogen Induced Cracking Survey in a Gas Oil Separation Plant (Case Study)...................................................................................................................................................1140
M. Al-Barout
08140 - Advances in Pipeline Radiography.................................................................................................1151J. Galbraith, G. Williamson, M. Creech
08141 - ECDA Indirect Assessment Methods - Limitations and Resolution in Presence of Dynamic Stray Currents...............................................................................................................................1158
Mark Yunovich
08142 -The Utilization of a Pipeline Integrity Management System for ECDA Management Within Gasunie..............................................................................................................................................1170
M.T. van Os, P. van Mastrigt, G.G.J. Achterbosch
08143 - Evaluation of Classification and Prioritization Criteria Based on the Results of Direct Examinations......................................................................................................................................1183
S.M. Segall, R.A. Gummow, R.G. Reid
08145 - Predicting Pipeline Corrosion Under Disbonded Coatings with the Influence of Slow Flow Underneath..................................................................................................................................1196
Fengmei Song, Narasi Sridhar
08146 - Pipeline Corrosion Monitoring by Fiber Optic Distributed Strain and Temperature Sensors ....................................................................................................................................1217
L. Zou, O. Sezerman, W. Revie
08147 - Impact of In-line Inspection Uncertainties on Decision Making Regarding Pipeline Integrity..........................................................................................................................................................1226
Marc Maes, Mamdough Salama
08148 - Rehabilitation Method for Gas Pipelines and Evaluation of Its Durability................................1236K. Tashiro, M. Kubouchi, T. Imagawa, Y. Higuchi, Y. Morita
08150 - A Case Study: ERW Seam Weld Failure .......................................................................................1248S. Limon, D. Katz, M. Gao, R. McNealy, R. Krishnamurthy
08151 - In-line Inspection Performance II - Validation Sampling ............................................................1258Roger McCann, Rick McNealy, Ming Gao
08153 - Prevention of Internal SCC in Ethanol Pipelines..........................................................................1271J. Beavers, M. Brongers, A. Agrawal, F. Tallarida
08157 - Waterline Protection in a Downtown Electric Rail Corridor ......................................................1295S. Greenberger, T. Elliott, K. Looijenga
08164 - A Corrosion Predictive Model for Use in Flowline and Pipeline Integrity Management ..........1307J. Garber, F. Farshad, J. Reinhardt, Hui Li, K.M. Yap, R. Winters
08166 - Complementing RBI Methodology in Predicting Materials Behavior with a Sophisticated Knowledge Management Tool ..............................................................................................1337
M. Renner, K. Weber, K. Schweier, W. Schlagner, M. Stanislowski
08167 - Expanded Risk Based Inspection - Corrosion Operating Windows ............................................1347K.F. Briegel
08173 - Cavitation & Erosion Damage of Reboiler Stripper Tubes in Gas Manufacturing Industry..........................................................................................................................................................1354
H. Rahmatalla, M.A. Maqbool, A.R. Al-Hajri
08174 - Unusual Corrosion Failures of Stainless Steel in Low Chloride Waters.....................................1377T. Mathiesen, J.E. Frantsen
08175 - Pharmaceutical Surface Defects: Correlation between Microstructural Artifacts and Electropolishing Results ........................................................................................................................1389
N. Eisinger, R.K. Raney, R. Avery
08176 - Common Corrosion Problems in the Brewery Sector ..................................................................1408J.E. Frantsen, K.U. Hattesen, P. Cheepsujjayan, B. Bertelsen, H.C. Aller
08177 - A NiCrMo Welding Product Provides Optimum Weldments in SuperDuplex Pipeline for Geothermal Power Service ......................................................................................................1429
G. Furmanski, S. Kiser, L. Shoemaker
08178 - Galvanic Corrosion Behavior of the Welded Joint of Ni-Based Alloy and X60 Steel in CO2 Saturated Solution ............................................................................................................................1447
L. Yang, W. Liu, M. Lu
Volume 3
08179 - Alloy Welding Products Multi-task to Reduce Maintenance Costs and Improve Process Reliability .........................................................................................................................................1460
L. Shoemaker, R. Golihue, B. Baker, S. Kiser
08180 - Corrosion Resistance of Alloy 31 and 59 in Highly Corrosive Dangerous Goods ......................1471M. Weltschev, R. Baessler, H. Werner, H. Alves
08181 - Corrosion Performance of a New Age-Hardenable Ni-Cr-Mo Alloy ..........................................1489N.S. Meck, L. Pike, P. Crook
08182 - Beneficial Effects of Tantalum in Ni-Cr-Mo-Ta Alloy UNS N06210 ...........................................1506K. Sugahara
08183 - Factors Affecting the Use of Zirconium in HCl Services..............................................................1518T-L Yau
08184 - Issues Around the Use of Zirconium in Sulfuric Acid ..................................................................1538T-L Yau, D. Holmes
08185 - Effects of Heat Treatment and Surface Condition on the Corrosion Resistance of Zirconium in Hydrochloric Acid..................................................................................................................1563
P. Snow, S. Sparkowich, M. Bozzello, A. Chang
08186 - Corrosion Properties of Duplex Stainless UNS S32003 Alloy ......................................................1590Bahri Ozturk, John J. Dunn, John F. Grubb
08189 - New Experiences with Nickel Alloys and Special Stainless Steels for an Optimized Material Selection in Acids at High Temperatures ....................................................................................1602
H. Alves, R. Baessler
08190 - The Corrosion Characteristics of a Uniquely Versatile Nickel Alloy ..........................................1617P. Crook, N.S. Meck, N.E. Koon
08191 - Protective Chemical Vapor Deposition Coatings for Stainless Steel Surfaces............................1627G.A. Barone, D.A. Smith, M. Higgins
08192 - Super-Ferritic Stainless Steels - The Cost Effective Answer for Heat Transfer Tubing ...........1634Daniel Janikowski & Edward Blessman
08193 - Some Aspects of Materials Selection for Condensing Economizers ............................................1650J. Kish, N. Stead, D. Singbell, F. Preto, F. Jette
08194 - Corrosion of Duplex Stainless Steels in High pH Caustic Solution .............................................1661Ananya Bhattacharya, Preet M. Singh
08196 - Failure Investigation of Electronic Components in Backup Generators ....................................1675A. Olszewski, R. Odle, R. Corbett
08197 - Using Electronic Tools and Databases to Manage Coatings used for Corrosion Control .........1690James A. Ellor, J. Peter Ault
08198 - Corrosivity Mapping of the Pacific Theater of Operations..........................................................1701G.A. Hawthorn, L.H. Hihara
08199 - Analysis of Corrosion Products Formed on Some of Ontario's Weathering Steel Bridges.......1718A. Coomarasamy, D. Lai, F. Pianca, T. Turi, S. Ramamurthy, B. Kobe, J.J. Walzak, J. Sawicki
08200 - Design of an Impedance Sensor for Monitoring Corrosion in Crevices......................................1745B. Klassen, P. Roberge
08201 - Field Deployed Corrosion Sensors on USMC Vehicles to Measure CPC Performance ............1756G. Tormoen, D. Dunn, A. Sabata, B. Sabata, J. Dante
08202 - Measurement of CPC Performance Using EIS-Based Sensor Methods - Laboratory and Field Studies ...........................................................................................................................................1769
M. Jakab, G. Tormoen, J. Dante
08203 - Corrosivity Monitoring System for Pipelines ................................................................................1785N.K. Brown, F.J. Friedersdorf
08204 - RF System for Corrosivity Monitoring ..........................................................................................1802James F. Dante, Aaron Steiner, Fritz Friedersdorf
08205 - Integrated Corrosion Detection, Treatment, and Management System for Potable Water Distribution Piping ............................................................................................................................1813
V. Van Blaricum, V. Hock, B.S. Phull, J.B. Bushman
08206 - Correlation of Electrochemistry and ASTM Tests in the Corrosion Behavior of 5XXX Aluminum Alloys ...............................................................................................................................1825
Elissa Bumiller, Robert Ruedisueli
08208 - Extended Performance Assessment in Accelerated Corrosion and Adhesion of Carc Prepared Aluminum Alloy 5059-H131 for Three Different Pretreatment Methods......................1837
B. Placzankis, A. Hilgeman
08209 - Improved Corrosion Resistance of Mg Alloy by Surface Al Electrodeposition..........................1857Jeng-Kuei Chang, Su-Yau Chen, Wen-Ta Tsai, Ming-Jay Deng, I-Wen Sun
08210 - Fastener Material Compatibility Evaluation for U.S. Marine Corps Ground Vehicles ............1867Darrell S. Dunn, Leonardo Caseres
08213 - Design of Novel Corrosion Inhibiting Additives............................................................................1880J. Elliott, R. Cook
08214 - Review of pH and Electrochemical Responsive Materials for Corrosion Control Applications ...................................................................................................................................................1887
W. Li, L.M. Calle
08215 - Smart Fluorescent and Self-healing Coatings for Steel Utilities at Army Installations .............1907Ashok Kumar, L. D. Stephenson
08217 - Environmentally Preferable Corrosion Protection of Structural Steel .......................................1919P. Lewis, J. Curran
08220 - The Use of Vitreous Enamel Coatings to Improve Bonding and Reduce Corrosion in Concrete Reinforcing Steel.......................................................................................................................1926
Vincent F. Hock, Sean W. Morefield, Donna. C. Day, Charles A. Weiss Jr., Cullen Hackler
08222 - Novel Technologies for Addressing Moisure in Earth Covered Magazines and Other Buried Structures ...............................................................................................................................1935
Orange S. Marshall,Jr., Sean Morefield, Michael McInerney, Vincent F. Hock
08223 - Investigation and Repair of Corrosion of Hull Forgings in Collins Class Submarines .............1948G. Sloan, P. Vince
08224 - Evaluating the Corrosion Protection of a Nuclear Submarine Drydock ....................................1963R. Tinnea, B. Ostbo
08225 - Evaluation of Corrosion Mitigation Technologies for Mechanical Room Plumbing and Union Joints at Military Facilities ........................................................................................................1978
Robert B. Mason, Lawrence A. Gintert, Mark F. Singleton, Vincent Hock, Richard Lampo
08226 - Sustain the Building - A Demonstration of Sustainable / Corrosion-Resistant Materials .........1990R. Lampo, T. Napier, K. Smith, E. Chien
08227 - Internal Inspection of 813 mm (32-inch) Red Hill Diesel Pipeline, FISC Pearl Harbor, Hawaii..............................................................................................................................................2000
T. Regin, M. Campos, M. Denham
08228 - the Effect of Ultrasonically Induced Cavitation Conditions on the Behavior Copper and Cobalt-based Alloys in Seawater ..........................................................................................................2011
A. Al-Hashem, H.Tarish, A. Akbar, N. Tanoli
08229 - Galvanic Corrosion Performance of High Strength Copper-Nickel Alloys in Seawater ...........2027R.C. Barik, J.A. Wharton, R.J.K. Wood, K.R. Stokes
08230 - A Pure Ternary High Molybdenum Containing Ni-Cr-Mo Alloy UNS N06059 (Alloy 59) Provides Reliable Solutions to Various Maintenance and Corrosion Problems in Naval / Marine Applications ...................................................................................................................................................2039
D. Agarwal
08231 - Effect of Seawater Chlorination on the Erosion Corrosion Behavior of Copper-Nickel Alloy CuNi90/10 ............................................................................................................................................2055
R. Feser, G. Schmitt, K. Schnier, T. Gommlich, S. Günther, W. Schleich
08232 - Pitting Corrosion Study in an AE 44 Magnesium Alloy ...............................................................2074R. Alvarez, A. Ruiz, M. Horstemeyer
08234 - Electrochemical Monitoring of Selective Phase Corrosion of Nickel Aluminum Bronze in Seawater .......................................................................................................................................2086
D. R. Lenard, C. J. Bayley, B. A. Noren
08236 - Investigation into the Corrosion Behaviour of Stainless Steel 316L in Hydraulic Fluids for Subsea Applications.....................................................................................................................2106
L. Zheng, A. Neville, A. Gledhill, D. Johnston
08237 - Corrosion Resistance of Si and Al Bearing Ultrafine Grained Weathering Steel in Saline Atmosphere ........................................................................................................................................2122
T. Nishimura, S. Tamilselvi
08239 - Corrosion of Civil War Era Sub Marine Explorer Intertidal Zonebay of Panama ...................2129Donald L. Johnson, Brent M. Wilson, James D. Carr, Larry Murphy, James Delgado
08248 - Crevice Corrosion Evaluation of N08367 Welds Applied by Different Welding Techniques ...2148T. Newbauer, K. Vasanth, E. Lemieux, K. Tran
08251 - Laboratory Testing of Seawater at Elevated Temperatures with Low Concentrations of Hypochlorite ...................................................................................................................2171
S. Standlee, K. D. Efird, K. May
Volume 4
08252 - Surface Reactivity of Thin Wall Ductile Iron -The Effect of Nodule Count and Microstructure...............................................................................................................................................2185
A.D. Sosa, M.D. Echeverría, O.J. Moncada, S.N. Simison
08253 - Validating Impressed Current Cathodic Protection Numerical Modelling Results Using Physical Scale Modelling Data...........................................................................................................2199
Y. Wang, K. KarisAllen
08254 - External Pitting and Crevice Corrosion of 316l Stainless Steel Instrument Tubing in Marine Environments and Proposed Solution .......................................................................................2219
A. Okeremi, M. Simon-Thomas
08256 - Localized Corrosion of a Super-Austenitic Stainless Steel (Fe-24Ni-20Cr-6.3Mo-0.22N) Brazed with Ni-Based Braze (Ni-22Cr-6.3Si-3.8P): Effect of Braze Clearance on Corrosion Resistance.......................................................................................................................................................2230
Joshua P. James, James M. Fitz-Gerald, John R. Scully
08257 - Corrosion of a Super-Austenitic Stainless Steel (Fe-24Ni-20Cr-6.3Mo-0.22N) Brazed with Nicrobraze 31 (Ni-22Cr-6.3Si-3.8P): Electrochemical Corrosion Behavior of Isolated and Combined Materials................................................................................................................2255
Sara Anastasio, Joshua James, Jim Fitz-gerald, George Young, Jr., John R. Scully
08259 - Successful Applications of Nickel Alloys and High Alloyed Stainless Steels in Seawater Service............................................................................................................................................2282
H. Alves, M. Schmitz-Niederau
08260 - An Enhanced Superaustenitic Alloy for Use in Severe Marine Service ......................................2299John F. Grubb, Bahri Ozturk, John J. Dunn
08261 - Corrosion Resistance of Duplex Stainless Steels in Thermal Desalination Plants......................2307S. Jacques, J. Peultier, J-C. Gagnepain, P. Soulignac
08263 - Corrosion Problems and Corrosion Mitigation Experiences on 6Mo Stainless Steel Seawater Systems on the Sleipner Platforms-North Sea ...........................................................................2324
S.venn Wigin
08265 - Modelling of Carbonate-Bicarbonate Stress Corrosion Cracking of Pipeline Steels .................2337Maftah H. Alkathafi, Robert A. Cottis
08266 - Crevice Corrosion Processes in Thin Films of Electrolyte ...........................................................2358Joe H. Payer, Xi Shan, Arun S. Agarwal, Uziel Landau
08270 - Monte Carlo Simulation of Localized Corrosion ..........................................................................2376G.R. Engelhardt, D.D. Macdonald
08271 - Effects of Oxygen, Temperature and Salinity n Carbon Steel Corrosion in Aqueous Solutions; Model Predictions versus Laboratory Results ..........................................................................2387
S.L. Grise, B.J. Saldanha
08272 - Modeling the Combined Effect of Chlorides and Oxyanions on Localized Corrosion ..............2396A. Anderko, N. Sridhar, M. Jakab, G. Tormoen
08273 - Cathodic Protection Modeling of Deep Wells Casing by 3D Software Simulation: Comparison with E-LogI and CPET Data ..................................................................................................2415
M. Roche, J. Vittonato, M. Jebara
08274 - Cathodic Protection Modeling of Buoy Chain Connector by 3D Software Simulation: Influence of Holes Size and Coating .......................................................................................2426
M. Roche, J. Vittonato
08279 - Expected Service Life and Cost Considerations for Maintenance and New Construction Protective Coating Work.......................................................................................................2438
J. Helsel, R. Lanterman, K. Wissmar
08280 - Systematic Integration of Advanced NDE and Corrosion Monitoring for Improved Refinery Reliability .......................................................................................................................................2460
E. H. Niccolls, A.E. Gallon, K. Yamamoto
08281 - Real-time, Online Corrosion Monitoring & Process Optimization Through the Chemical Plant Control System ...................................................................................................................2471
J. Hernandez, R. Kane, K. Briegel, R. Clark
08285 - Using Ultrasound Measurements for Real-time Process Control of Pipelines and Process Equipment Subjected to Corrosion And/or Erosion ....................................................................2485
Ø. Baltzersen, T. Rommetveit, R. Johnsen
08286 - Real Time Corrosion Monitoring to Assess the Corrosivity of Oil Water Mixtures and the Kinetics of the Response to Imidazoline Based Corrosion Inhibitors .........................................2498
W. Villamizar, C.S. Magana, H. Chow, G.G. Rodriguez, M. Casales, L.M. Gomez
08290 - Remote Monitoring of Pipeline Corrosion Using Fiber Optic Sensors .......................................2507Don Morison
08292 - Experiences of Remote Monitoring and Controlling Systems in CP ...........................................2516HongSeok Song, YoungGeun Kim, KyoungWan Park
08293 - Field Test of High Temperature Corrosion Sensors in a Waste to Energy Plant.......................2523S. A. Matthes, B. S. Covino Jr., S. J. Bullard, K. M. Williamson
08294 - Corrosion Monitoring at the Coleson Cove Generating Station ..................................................2543K. McKeen, M. Lalonde, A. Scott, K. Leblanc
08295 - Corrosion Monitoring of a Water Based Rolling Facility with Coupled Multielectrode Array Sensors and the Correlations with Other Process Variables: Conductivity, pH, Temperature, Dissolved Oxygen and Corrosion Potential ........................................................................2554
R. Colbert, R. Reich
08296 - Automated Corrosion Loggers for Corrosion Monitoring in the Atmosphere...........................2569T. Prosek, D. Thierry, M. Kouril, Y. Degres
08297 - Monitoring of Effectiveness of Dehumidification System for Corrosion Control Inside Upper Steel Box Girder in Yeongjong Grand Bridge Using Thin-film Electrical Resistance Sensors.........................................................................................................................................2575
SeonYeob Li, Sungwon Jung, Kyeong-Wan Park
08300 - Implementation of Advanced Electronic Techniques for Remote Monitoring of Cathodic Protection, Scour and Environmental Conditions for Marine Bridges in Florida..................2591
Richard J. Kessler, Rodney G. Powers, Ivan R. Lasa
08301 - Condition Assessment and Cathodic Protection of Reinforced Concrete Cooling Tower.........2603Zia Chaudhary, Fahad M. Al-Mutlaq, Ali Al-Beed
08302 - Arresting and Preventing Corrosion of Steel in Concrete............................................................2623N. Davison, A. Roberts, G. Glass
08303 - Cathodic Protection at Durrat Al Bahrain ....................................................................................2633R. Callon
08305 - Long Term Behaviour of Ceramic Tubular Shaped Anodes for Cathodic Protection Applications.................................................................................................................................2653
G Sergi, D Simpson, P. Hayfield
08306 - Long-term Protection of Reinforced Concrete by Galvanic Cathodic Protection - Test Results ....................................................................................................................................................2664
J. Bennett, W. McCord
08307 - Sacrificial Cathodic Protection of Partially Submerged Reinforced Concrete Elements by Magnesium Sacrificial Bulk Anodes with Experimental and Modeling Results ...............2677
F. Presuel-Moreno, W. Hartt
08308 - Modeling of Polarization by Point Anodes for Prevention of Reinforcing Steel Corrosion .......................................................................................................................................................2695
M. Dugarte, A.A. Sagüés, R.G. Powers
08310 - Recent Developments in Data-Logging Covermeters and the Interpretation of Results...........2711J.F. Fletcher
08311 - Corrosion of Epoxy Coated Rebar in Cracked Marine Substructure Concrete ........................2722K. Lau, A. Sagues, R. Powers
08312 - Characterizing Corrosion Behavior of Disbonded Epoxy Coated Reinforcing Steel - Updated Results ..........................................................................................................................................2735
Seung-Kyoung Lee
08313 - Corrosion Resistance of Alternative Reinforcing Bars: An Accelerated Test ............................2752F. Cui, P. Krauss, S. Humphreys
08315 - Galvanic Liquid Applied Coating for the Protection of Concrete Reinforcement .....................2768A. Hansen, A. Furman, M. Hansen, A. Green, J. Meyer
08317 - Evaluation of Hydrophobic Concrete Coatings in Tropical Marine Environments ..................2781Oladis Troconis de Rincón, Marianna Aboulhosn, Carmen Morales, José Bravo, Miguel Sánchez, Daniel Contreras, Yolanda Hernández, Valentina Millano
08318 - Behavior of Coastal Concrete Housings Against Environmental Loading in the Caribbean ......................................................................................................................................................2804
Rómel G. Solís-Carcaño, Eric I. Moreno, Pedro Castro-Borges, Felipe Jimenez-Torres, Rogeli Marquez-Novelo
08319 - Long Term Corrosion Performance of Soil Reinforcement in Mechanically Stabilized Earth Walls ..................................................................................................................................2813
B.S. Berke, A.A. Sagüés, R. Powers
08320 - Specimen Type and Test Protocol for Corrosion Performance Characterization of Reinforced Concrete Marine Pilings ...........................................................................................................2822
Russell E. Tanner, William H. Hartt
08321 - Modeling Analysis for the Effects of Non-Diffusive Coarse, Aggregate on Time-to-Corrosion and Corrosion Initiation Site .....................................................................................................2838
Hui Yu, Yueyue Deng, William H. Hartt
08322 - Effect of Cement Alkalinity Upon Chloride Threshold and Time-to-Corrosion of Reinforcing Steel in Concrete.......................................................................................................................2858
William H. Hartt, Jingak Nam
08323 - Cathodic Behavior of Stainless Steel 316LN Reinforcing Bars In Simulated Concrete Pore Solutions................................................................................................................................2877
F. Cui, A. Sagues
08325 - Laboratory Evaluation and Modeling of Api-l80/13Cr Galvanic Corrosion in CO2 Environment ..................................................................................................................................................2895
C. Mendez, C. Scott
Volume 5
08332 - Roles of Passivation and Galvanic Effects in Localized CO2 Corrosion of Mild Steel...............2917
Jiabin Han, Yang Yang, Srdjan Nesic, Bruce N Brown
08333 - The Effect of Acetic Acid on the Integrity of Protective Iron Carbonate Layers in CO2 Corrosion of Mild Steel.........................................................................................................................2936
Vanessa Fajardo, Christian Canto, Bruce Brown, David Young, Srdjan Nesic
08334 - Fighting Internal Corrosion - A Big Challenge to Maintain Sustainable Oil Production in Romania.................................................................................................................................2950
Wolfgang Havlik, Karin Thayer, Markus Oberndorfer, Mariana Salcu
08343 - Interaction of Carbon Dioxide Corrosion Inhibitors with Corrosion Products Deposit ...........2962Martin Foss, Egil Gulbrandsen, Johan Sjöblom
08344 - Experimental Evaluation of Corrosion Inhibitor Performance in Presence of Iron Sulfide in CO2/ H2S Environment ................................................................................................................2981
Mohsen Achour, Juri Kolts, Phillip Humble, Roger Hudgins
08345 - Effect of Corrosion Inhibitor Active Components on the Growth of Iron Carbonate Scale under CO2 Conditions.........................................................................................................................2992
J. Wong, N. Park
08347 - Understanding The Nature of the Mineral Scale Problems in Ghawar Gas Condensate Wells to Describe and Apply the Right Approach of Mitigation..........................................3017
C.A. Franco, H.M Al-Marri, M.A. Al-Asiri, H.M. Al-Hussain
08350 - Root Cause Failure Analysis, Removal and Mitigation of Iron Sulfide Scale Deposition in the BP Bruce Produced Water Rejection Plant ..................................................................3053
J. Wylde, A. Duthie, H. McAllister
08351 - Assessment of CaCO3 Inhibition by the Use of SXRD on a Metallic Substrate..........................3072A. Martinod, A. Neville, K. Sorbie, Z. Zhong
08354 - Barium Sulfate Scale Management Redefined: The BP Bruce AI4(A8) Success Story .............3084J. Wylde, A. Duthie, B. Cornock, I. MacRae, D. Bertovic
08356 - The Influence of Overflush Fluid Type on Scale Squeeze Life Time - Field Examples and Placement Simulation Evaluation .......................................................................................3101
M.M. Jordan, E.J. Mackay, O. Vazquez
08357 - The Development of a Scale Management System for the Control of Calcium Carbonate in an Offshore Oil Production Pipeline System .......................................................................3121
S. Laggat, P. Allison, R.N.R. Sahar, T.S. Hain, A.G. Hunton, M.J. Thompson
08359 - Assessment of the Effect of Volatile Corrosion Inhibitors on the Operational Efficiency of Electrical Motors.....................................................................................................................3137
Eric Uutala
08363 - Evaluation of DBU as Corrosion Inhibitor for Secondary Cycle Pressurized Water Reactor ...........................................................................................................................................................3145
H. Namduri, S. Nasrazadani
08364 - PIXE Spectroscopy for Determination of Volatine Corrosion Inhibitor Concentration in Anticorrosion Polymer Films .........................................................................................3152
I. Pucic, M. Jaksic, T. Madzar, I. Rogan
08367 - A Broad Review of Various Waters and Their Potential, After Pretreatment, for Re-use in Cooling Systems with a Focus on the Selection and Application of Modern Specialty Inhibitor Chemistries ....................................................................................................................................................3164
Colin Frayne
08368 - An Evaluation of Silica Scale Control Additives for Industrial Water Systems.........................3180Z. Amjad, R. W. Zuhl
08369 - Zero Liquid Discharge Operation of Cooling Towers at a Major Steel Mill ..............................3192John Kubis, Jeff Reed
08370 - Water Reuse Strategies: Steel Industry Case Studies ...................................................................3206David Christophersen
08372 - Electrochemical Studies with Coupled Multielectrode Array Sensors on Corrosion Inhibition of Copper and Affected Metals in the Presence of Ammonia and Other Corrosive Ions in Zero Liquid Discharge Cooling Water..........................................................................3221
Dan Duke, Lietai Yang
08373 - The Impact of Reclaimed Water of Two Different Qualities on Two Similar Power Plants.....3238Daniel Robinette
08374 - Magnesium Hydroxide Deposit Control for Reverse Osmosis Systems ......................................3278Suresh Patel, John Milligan
08375 - Laboratory Investigations of Corrosion Phenomena in Simulated Defense Nuclear Waste Solutions .............................................................................................................................................3292
G. Edgemon, D. Wilson, V. Anda
08376 - The Effect of Flow on Electrochemical Noise Generation ............................................................3317Mukhtar Shaglouf, Robert A. Cottis
08377 - Corrosion Performance of a Carbon Steel Exposed to LiBr-H2O Solution at Low Temperatures ................................................................................................................................................3326
C.C. Arteaga, C.F.C. Sedano, B. Campillo
08378 - Corrosion Performance of a Bio-based Glycol for Process Cooling Applications......................3338Mingzhang Wang, Satish C. Mohapatra
08379 - Characterization of Copper Corrosion Products Formed in Drinking Water by Combining Electrochemical and Surface Analyses ....................................................................................3346
Young C. Kang, Wim J. van Ooij, Darren Lytle
08380 - Galvanic Behavior of Aluminized Steel Type 2 with Coating Breaks in Waters of Varying Scaling Tendencies .........................................................................................................................3365
L. Caseres, A. Sagues
08382 - Rp Measurements: Potentiostatically or Galvanostatically .........................................................3382A. Guyader, F. Huet, R. P. Nogueira
08383 - In-plant Electrochemical Measurements on Austenitic Stainless Steel Equipment Operated at Elevated Temperatures ...........................................................................................................3396
S. Schultze, S. Bender, J. Gollner
08384 - Electrochemical Corrosion Study of Silicon in Potassium Formate Solutions ...........................3409Mingzhang Wang, Satish C. Mohapatra
08388 - Corrosion of Carbon Steel in Petrochemical Environments ........................................................3415B.G. Santos, F. King
08389 - Microelectrochemical Techniques for Characterization of the Behaviour of Corrosion Resistant Alloys (CRA) ...............................................................................................................3426
Thomas Ladwein, Matthias Sorg, Jens Maier
08391 - An Electrochemical Approach for Quantifying Flash Rusted Surfaces after Ultra High Pressure Waterjetting..........................................................................................................................3434
M. Islam, J. Tagert, W. McGaulley
08393 - In-situ Monitoring of Organic Coatings Under QUV/Prohesion Exposure by Embedded Sensors ........................................................................................................................................3445
K. Allahar, Q. Su, G. Bierwagen
08395 - A Method to Reduce the Internal Current Effect on Localized Corrosion Measurements with Coupled Multielectrode Array Sensors.....................................................................3461
L. Yang, X. Sun
08396 - Corrosion Assessment of Mechanically Formed Aluminized Steel..............................................3474M. Akhoondan, A. Sagues, L. Caseres
08398 - Detection of Corrosion of Post-tensioned Strands in Grouted Assemblies .................................3485L. V. Taveira, A. A. Sagüés, J. Lopez-Sabando, B. Joseph
08400 - Investigations on Defined Pretreated Magnesium Alloys by Means of Electrochemical Noise ...................................................................................................................................3504
S. Bender, J. Goellner, A. Heyn, S. Schultze
08401 - Influence of the Cathodic Process on the Electrochemical Noise from Pitting of Stainless Steel.................................................................................................................................................3521
H. Klapper, A. Heyn, J. Goellner
08402 - Development of a Prototype Field Device for Characterizing the Level of Flash Rust Formed after Ultra High Pressure Waterjetting ...............................................................................3530
M. Islam, J. Tagert, W. McGaulley
08403 - Corrosion of Metals in Contact with Treated Wood: Developing Test Methods .......................3543 S. Zelinka, D. Rammer, D. Stone
08405 - Hydrogen Permeability Behaviour of a High Strength Microalloyed Steel Developed for Sour Service ..........................................................................................................................3552
S. Serna, Erick R. Morales, J. G. González-Rodríguez, A. Torres, B. Campillo, J. Juarez-Islas
08407 - Hydrogen Permeation of Alloy 22 ..................................................................................................3564M.L. Taylor, L.G. McMillon
08408 - The Effect of Pressure on Hydrogen Charging of Carbon Steel Under Cathodic Protection .......................................................................................................................................................3579
F.W.H. Dean, S.W. Powell, B. Muckherjee, C.M. Fowler
08409 - New Insights Into Hydrogen Permeation in Steels: Measurements Through Thick Membranes ....................................................................................................................................................3591
J. Kittel, F. Ropital, J. Pellier
08410 - Hindrance of Hydrogen Effusion from Steel by Coatings and Layers ........................................3613G. Schmitt, K-K Ma
08411 - Hydrogen Production and Permeation in Near-Neutral pH Environments ...............................3629S. Asher, P.M. Singh
Volume 6
08412 - Influence of H2S and CO2 Corrosion Scales on Hydrogen Permeation in X65 Steel .................3648
Jianwei Yang, Lei Zhang, Lining Xu, Minxu Lu
08414 - Corrosion Rate Measurements in the Presence of Hydrogen Sulfide: Electrochemical Activity of Solution Species ..............................................................................................3656
D. Miller, K.D. Efird, N. Davis, A. Ali, J. Ward
08415 - Black Powder in Gas Transmission Systems .................................................................................3677A.M. Sherik, S.R. Zaidi, E.V. Tuzan
08416 - Corrosion Challenges in Gas Treating Units .................................................................................3692M.A. Saleem, A.A. Hulaibi
08417 - A Verified Computer Model for Corrosion Rate Prediction in a Di-Ethanol Amine System Using Field Data ...............................................................................................................................3706
Mahdi Nouri, Jafar Mesbah, Soheil B. Shaibani
08418 - Corrosion Management Practices Applied in Design and Installation of Submarine Pipelines in High Pressure High Temperature (HPHT) Gas Production.................................................3730
J.R. Valdez Vallejo, H. Guan, M. Ismail
08419 - Corrosion Problems in Gas Treat Systems ....................................................................................3740Mark A. Moore, Majed. M. Qarni & Graham R. Lobley
08421 - Improving Amine Unit Reliability with On-line Corrosion Monitoring & Modeling................3750Pilar Quiroga, Russell D. Kane, Marta Castillo, Vishal Lagad
08422 - Corrosion Control Methods in Supercritical Water Oxidation and Gasification Processes .....3767P. Marrone, G. Hong
08425 - Effect of Shot Peening on the Oxidation of Ferritic-Martensitic Steels in Supercritical Water.......................................................................................................................................3807
X. Ren, K. Sridharan, T.R. Allen
08428 - SCC Crack Growth Rates of Austenitic Alloys in Supercritical Water ......................................3819Sébastien Teysseyre, Gary S. Was
08430 - Corrosion of Materials in Supercritical Carbon Dioxide Environments ....................................3829J. Y. Lim, T.J. McKrell, G. Eastwick, R. G. Ballinger
08431 - Passivation Films Behavior of Stainless Steel under High Temperature and Pressure Anhydrous Methanol Solution Containing Chloride .................................................................3847
D. Shintani, T. Fukutsuka, Y. Matsuo, Y. Sugie, T. Ishida
08432 - Role of Microstructure on Stress Assisted Corrosion Cracking of Carbon Steel Boiler Tubes...................................................................................................................................................3856
Dong Yang, Preet M. Singh , Richard W. Neu
08433 - Analysis of Steam Superheater Tubes Failures of Medium-Pressure Boilers ............................3870Veronica A. Dominguez, Roberto Tedesco, Pablo G. Peña
08436 - Boiler Tube Failures and Integrity Assessment ............................................................................3884M.A. Saleem, A.A. Hulaibi
08437 - Failure Analysis and Investigation Methods for Boiler Tube Failures II: Additional Case Histories ................................................................................................................................................3894
Mehrooz Zamanzadeh, Edward S. Larkin, George T. Bayer, William Linhart
08438 - Evaporator Failure Caused by Corrosion and Flow.....................................................................3931P. Yoffe
08439 - What Happens When Real World Operation of Steam Generators Deviates from Design Conditions..........................................................................................................................................3939
D. DeWitt-Dick, E. Beardwood
08440 - Failure Analysis of Bank Tube in Package Boiler.........................................................................3968A.K. Bairamov, Saud Al-Subai, R. Bradley, C.E. van der Westhuizen
08441 - Boiler Operation for Tanker Conversion.......................................................................................3979C. Haarseth, R. Franco
08442 - Weld Overlay Materials for Extending the Life of Boiler Tubes in Coal Fired Power Plants ..................................................................................................................................................3990
Larry Paul
08443 - Protective Aluminide Coatings for NiCr Alloys in Combustion Environments .........................4007B. A. Pint, P. J. Maziasz, J. Schauer, V. Levin
08444 - Extending the Service Life of Furnace Wall Tubes Using Thermal Sprayed Coatings .............4022Y. Matsubara, Y. Sochi, M. Tanabe, A. Takeya
08446 - High Temperature Oxidation of Heat-Resistant Alloys in Combustion Environments ................................................................................................................................................4035
James Rakowski
08447 - Influence of Pressure and Chromium Content on Corrosion Reactions at 600°C in a CO2-H2O Atmosphere................................................................................................................................4043
D. Huenert, A. Kranzmann
08449 - Scale Formation on Si-Containing Steels .......................................................................................4062Cheng-Hsien Yang, Wen-Ta Tsai, Szu-Ning Lin, Chih-Hsiung Chen
08452 - Material Solutions for the Thermal Treatment in High Chlorine Environments ......................4073B. Rammer, M. Schütze, T. Weber, R. Bender
08454 - Stress Relaxation Cracking of Welded Joints in Thick Sections of a TP347 Stabilized Grade of Stainless Steel...............................................................................................................4083
Christian van der Westhuizen
08456 - Effect of Oxyfuel Combustion on Superheater Corrosion ...........................................................4101Bernard S. Covino Jr., Steven A. Matthes, Sophie J. Bullard
08458 - Thermal Fatigue in a De-Superheater Induced by Thermal Loads ............................................4110Bakheet Al-Yami, Ali Babakr, Mohammed Al-Sonidah, Ron Bradley, Raja Imtiaz
08460 - Materials Performance of Ferritic Steel in Combustion Gases for Heat Exchanger Applications in Solid Oxide Fuel Cell Systems ...........................................................................................4120
M. Ziomek-Moroz, T. Adler, P. King
08461 - Environmental and Compositional Effects on the Hot-corrosion Behavior of Ni-based Alloys and Coatings.......................................................................................................................................4129
V. Deodeshmukh, B. Gleeson
08462 - SEM and Hot Corrosion Evaluation of 80Ni-20Cr Coating Applying Electrochemical Techniques.........................................................................................................................4141
C. Cuevas Arteaga, S. Serna, J.P. Calderon
08463 - Oxidation of a Single Crystal Nickel-Base Superalloy at 950°C - A Kinetic and Microstructure Study....................................................................................................................................4151
A. Pfennig, A. Kranzmann
08464 - High Temperature Gas Corrosion of Fe-Cr-Ni-Al-La Alloy........................................................4160E.R. Kutelia, O.O. Tsurtsumia, B.P. Bulia, O. I. Mikadze, S. Bakhtiyarov
08466 - A Study of the Chemical Composition and Corrosivity of the Condensate in Top of the Line Corrosion ........................................................................................................................................4169
Dezra Hinkson, Marc Singer, Ziru Zhang, Srdjan Nesic
08470 - Top of the Line Corrosion in H2S /CO2 Environments.................................................................4184A. Camacho, M. Singer, B. Brown, S. Nesic
08471 - The Use of Inspection Results for the Evaluation of Batch Treatment Efficiency and the Remaining Life of the Pipelines Subjected to Top of Line Corrosion.........................................4206
M. Thammachart, Y. Gunaltun, S. Punpruk
08480 - Sulfide Stress Cracking of Pipeline-Case History .........................................................................4218D. Masouri, M. Zafari, A.M. Araghi
08481 - Potential Effect Over the Stress Corrosion Cracking Behavior of a X-70 Microalloyed Pipeline Steel in Dilute NaHCO3 Solutions..........................................................................4226
A. Torres-Islas, J. G. González-Rodríguez, J. Uruchurtu, S. Serna
08483 - A New Chemical Mechanistic Postulate Regarding Annular Environmentally Assisted Cracking (AEAC) - Importance of Cations and Key Contaminants in Packer Fluids in Cracking of Martensitic Stainless Steel .......................................................................................4244
J. McKennis, N. Bae, M. Kimura, K. Shimamoto, H. Sato
08484 - Low Temperature Stress Corrosion Cracking of Stainless Steels in the Atmosphere in Presence of Chloride Deposits..................................................................................................................4260
T. Prosek, A. Iversen, C. Taxen
08485 - Stress-Corrosion Crack Initiation of Type 304 Stainless Steel in Atmospheric Environments Containing Chloride: Influence of Surface Condition, Relative Humidity, Temperature and Thermal Sensitization ....................................................................................................4277
N.D. Fairweather, N. Platts, D.R. Tice
08486 - Applying a Multi Method Approach to Chloride Induced SCC of Two Austenitic Cr-Ni-Mo-N Stainless Steels .........................................................................................................................4293
S. Holzleitner, W. Kranister, G. Mori, P. Schmuki
08487 - Results from Low Temperature Creep and Relaxation Experiments of Four Different Stainless Steels...............................................................................................................................4311
U.H. Kivisäkk, E. Wallin
08488 - Corrosion Fatigue of a CrMnN Stainless Steel..............................................................................4322R. Sonnleitner, G. Mori, M. Panzenbock, R. Fluch, S. Eglsaer
08489 - Fluid-induced Fatigue Closure Effects in Aqueous Solutions: Verification and Implications ...................................................................................................................................................4343
T.M. Ahmed, D. Tromans
08490 - Water Effects on Adhesion and Wear Resistance of Chromium Oxide Coatings ......................4364Xiaolu Pang, Alex A. Volinsky, Kewei Gao
Volume 7
08492 - Effects of Temperature and Humidity on Atmospheric Stress Corrosion Cracking of 304 Stainless Steel .....................................................................................................................................4375
H. Hayashibara, M. Mayuzumi, Y. Mizutani, J. Tani
08494 - Environmentally-Assisted Cracking Behavior of Alloy 182 Weld in Sulfuric Acid Solution ..........................................................................................................................................................4384
Chien-I Huang, Chen-Hao Yang, Wen-Ta Tsa
08495 - A Multi-Scale Approach to Stress Corrosion Cracking ...............................................................4391S. Lozano-Perez, C. English, T. Terachi, T. Yamada
08496 - The Effect of Metallurgical Factors on SSC of High Strength Pipeline Steel .............................4400W.K. Kim, K.Y. Kim, T.W. Yun, B.Y. Yang
08497 - A Study of Pressure Limits of Double Q&T P110 in Low H2S Environments ...........................4409M. Gao, R. Krishnamurthy, David Lewis, David Copeland, Bruce Urband
08500 - The Influence of Weld Heat-Affected Zone on Stress Corrosion Cracking of Pipeline Steel in Near-neutral pH Environment.........................................................................................4425
B. Fang, E-H Han, J. Wang, W. Ke, R. Eadie, M. Elboujdaini, W. Zheng, W. Revie
08502 - Detection and Identification of Microbially Influenced Corrosion (MIC) in Steels...................4436Donald L. Gibbon, Mehrooz Zamanzadeh
08503 - Validation of a Predictive Model for Microbiologically Influenced Corrosion ..........................4450Reeta Sooknah, Sankara Papavinasam, R. Winston Revie
08504 - Evaluation of Cathodic Protection in Presence of Sulfate Reducing Bacteria Mixed Cultures..........................................................................................................................................................4467
Matilde F. de Romero, Oladis T. de Rincón, Mónica Sanz, Brendy Rincón, Lisseth Ocando, William Campos, Mariangela Bracho
08505 - MIC of Steels by Iron Reducing Bacteria ......................................................................................4485H. Videla, S. LeBorgne, C. Panter, R.K.S. Raman
08507 - Corrosion Inhibition in PWRI Systems That Use Nitrate Treatment to Control Treatment to Control SRB Activity and Reservoir Souring .....................................................................4495
J. F. D. Stott, G. Dicken, T. Y. Rizk, C. Gamble, S. Saul, T. Granli, T. Haegh
08508 - MIC in Fire Sprinkler Systems Field Observations and Data .....................................................4515Ockert J. Van Der Schijff
08512 - Mechanistic Modeling of Anaerobic THPS Degradation in Seawater Under Various Conditions........................................................................................................................................4523
Kaili Zhao, Jie Wen, Tingyue Gu, Ardjan Kopliku, Ivan Cruz
08513 - Application of DGGE and Fish Analyses in Seawater Injection Systems ...................................4540Heike Hoffmann, Carol Devine, Stephen Maxwell
08515 - HDPE Solves Alkylation Sewer Corrosion Problem in Refinery.................................................4553Christine Osborne
08516 - Replacing Corroded and Failed Metallic Pipe with Corrosion Resistant FRP Pipe Design and Installation Requirements and a Case History .......................................................................4561
Robert Hawkins
08517 - Industrial Case Histories of the ECTFE Resin..............................................................................4569J.K. Argasinski
08518 - Long Term Corrosion Protection and Refurbishment of Process Equipment, Using Glassflake Filled Composite Linings. ..........................................................................................................4578
Graham Greenwood-Sole
08519 - A History of Coatings and Linings as Corrosion Protection in Flue Gas Desulphurization Plants................................................................................................................................4590
W. Berger, J. Fenner, P. Pfeil
08520 - Innovative New Chimney Design for Wet Flue Gas......................................................................4598Paul Nederlof
08524 - What is the Best Resin for FRP Sodium Hypochlorite Storage Tanks?......................................4610Michael Stevens
08527 - Opportunities for Nonmetallic Composites and Glass Reinforced Coatings in Gas Processing Plants ...........................................................................................................................................4619
M.A. Saleem, A.A. Hulaibi
08528 - Failure Analysis of Plastics - Methodology and Case Studies ......................................................4628Mehrooz Zamanzadeh, Colleen S. Miller, George T. Bayer
08530 - Applications for Polyvinylidene Fluoride and Its Copolymers for Corrosion Resistance in the Chemical Process Industry .............................................................................................4656
David Seiler, Jaclyn Sekula
08531 - Thermoplastic Lining - Long Term Corrosion Protection of Underground Structures............4664A. Lueghamer
08532 - Influence of Material Quality on the Performance of Thermoplastic Piping Systems ..............4677A. Lueghamer, M. Haager
08533 - The Effect of Highly Concentrated Chlorine Dioxide on Physical Properties of Fluoropolymers .............................................................................................................................................4693
L.M. Dobosz, J.K. Argasinski, T.V. Tran
08535 - A New Updated Model of CO2/ H2S Corrosion in Multiphase Flow ...........................................4704S. Nešic, S. Wang, H. Fang, W. Sun, J. K-L. Lee
08536 - Using Multiphase Flow Modeling for the Selection and Application of Corrosion Inhibitors in Northern U.S. and Western Canada .....................................................................................4720
Jorge Paez
08538 - Experimental and Theoretical Investigation of the Uniform Corrosion in the Annulus of Offshore Flexible Pipelines .......................................................................................................4737
E. Remita, F. Ropital, J. Kittel, B. Tribollet, E. Sutter, C. Taravel-Condat, N. Desamais
08539 - Predicting Galvanic CO2 Corrosion in Oil and Gas Production Systems ...................................4754J.R. Vera, S. Hernandez, C. Scott, O. Moghissi
08540 - Prediction of Erosion-Corrosion in Oil and Gas - A Systematic Approach................................4775X. Hu, A. Neville, J. Wells, V. DeSouza
08541 - Assessment of CO2 Corrosion Damage Distribution in Oilwells by Deterministic and Stochastical Modelling...........................................................................................................................4784
Raymundo Case
08542 - Further Validation of an Internal Pitting Corrosion Model ........................................................4812S. Papavinasam, A. Demoz, O. Omotoso, K. Michaelian, R.W. Revie
08545 - Modeling Pitting Corrosion in a CO2 System Containing Bacteria.............................................4843James Garber, Kathleen Knierim, Juan Acuna, Karan Deokar
08546 - Prediction of Interactions Between FPSO and Subsea Cathodic Protection Systems ...............4867R.A. Adey, J. Baynham, R. Jacob
08547 - Furnace Tube Life Assessment as Impacted by the Methodology Used .....................................4877Jorge L. Hau, Antonio Seijas
08548 - Hydrogen Permeation Application to Crude Unit Overhead Corrosion Monitoring ................4903F. Al-Faqeer, F. Addington
08549 - Role of Nascent Hydrogen in Refinery Corrosion.........................................................................4912Barry Messer, Vasile Oprea, Keith Beaulieu, Andrew Wright
08551 - Refinery Caustic Injection Systems: Design, Operation, and Case Studies ................................4933A. Al-Omari, A. Al-Zahrani, G. Lobley, R. Tems, O. Dias
08553 - Flux-Core Welding in Refinery Service Historical Obstacles, Industry Practices, & Recent Developments ....................................................................................................................................4949
Richard Colwell, William Layo
08555 - The Effect of Molybdenum on Stainless Steels and Naphthenic Acid Corrosion Resistance.......................................................................................................................................................4965
G. Gallo, J. Edmondson
08556 - Desalter Acidification Additives and Their Potential Impacts on Crude Units..........................4978S. Lordo, J.M. Garcia, S. Garcia-Swofford
08557 - Resisting Petroleum Refinery Corrosion with Nickel Alloys .......................................................4990L.E. Shoemaker, G.D. Smith, B.A. Baker, & S.D. Kiser
08558 - A Refinery Approach to Address Corrosion Under Insulation & External Corrosion .......................................................................................................................................................5000
Rob Scanlan, Ricardo Valbuena, Ian Harrison, Rafael Rengifo
08559 - Effect of Hydrogen on Mechanical Behavior for 2 1/4 Cr1Mo Steel Grades (Standard and Vanadium Added)................................................................................................................5035
S. Pillot, P. Bourges, G. Masson, L. Coudreuse, P. Toussaint
08561 - Investigation of Inhibiting Quality of Different Oil Types at Different Oil/water Cuts, Temperatures and Velocities in a Laboratory Multiphase Pump...................................................5054
Oliver Klein, Hans Hoffmeister, Marten Gerlach
08562 - Effect of Flow on Corrosion and Its Inhibition in Riser Pipelines...............................................5069Cheolho Kang, Parimal P. More, José Vera, Pedro Altoe Ferreira, Eduardo Costa Bastos, Marcelo Araujo
08564 - Predicting the Curvature of the Interface for an Oil/water Flow and Its Effects on Corrosion .......................................................................................................................................................5082
C. Deng, K. Adams, T. MacFarlane
Volume 8
08565 - The Effects of Flow Pattern Transitions of Threephase Flows on Corrosion.............................5101
C. Deng, K. Adams, T. MacFarlane
08566 - Determination of Phase Wetting in Oil-water Pipe Flows............................................................5122François Ayello, Chong Li, Xuanping Tang, Jiyong Cai, Srdjan Nešic, C. Ivan T. Cruz, Jamal N. Al-Khamis
08568 - A Study of Impact of Corrosion Generated Particles on a Water Injection System Design .....5136Y. Chen, P. Nichols, M.J.S. Thomas
08570 - Effect of a Corrosion Inhibitor for Oil and Gas Wells When Sand is Produced........................5148K. Dave, K. Roberts, J. Shadley, S. Ramachandran, E. Rybicki, V. Jovancicevic
08571 - Erosion-Eorrosion of Corrosion Resistant Alloys Used in the Oil and Gas Industry ................5162H. Rincon, J. Shadley, K. Roberts, E. Rybicki
08572 - Erosion-Corrosion in Disturbed Liquid/Particle Flow .................................................................5181J. Addis, B. Brown, S. Nesic
08573 - Erosion-Corrosion Test Method Development and Chemical Screening....................................5195Martin Willis
08575 - Effect of Crevice Former on the Evolution of Crevice Damage...................................................5208Xi Shan, Joe Payer
08576 - Durability of Passive Films in High Temperature Brines ............................................................5230Xi Shan, Joe Payer, Pallavi Pharkya
08578 - Effect of Organic Acid Additions on the General and Localized Corrosion Susceptibility of Alloy 22 in Chloride Solutions .........................................................................................5244
Ricardo M. Carranza, C. Mabel Giordano, Martín A. Rodríguez, Raul Rebak
08579 - Anodic and Cathodic Behavior of Mill Annealed and Topologically Closed Packed Alloy 22 in Chloride Solutions......................................................................................................................5264
Ricardo M. Carranza, Martín A. Rodríguez, Raul Rebak
08580 - Environmental and Metallurgical Variables Affecting Crevice Corrosion Susceptibility of Alloy 22 - A Review...........................................................................................................5289
Ricardo M. Carranza
08581 - Simple Algorithms for Oxygen Concentration Distribution in an Occluded Region.................5305Fengmei Song
08582 - Effects of Test Methods on Crevice Corrosion Repassivation Potential Measurements of Alloy 22 ............................................................................................................................5327
Xihua He, Blair Brettmann, Hundal Jung
08583 - Cathodic Capacity of Alloy 22 in the Potential Yucca Mountain Repository Environment .....5352P.K. Shukla, R. Pabalan, T. Ahn, L. Yang,, X. He, H. Jung
08585 - An Examination of the Chromium-Rich Passive Film's Formation on Alloy 22 in Mildly Alkaline Environments .....................................................................................................................5383
Todd S. Mintz, Hipolito J. Gonzalez, , Yi-Ming Pan
08587 - Protective Insulated Coating for Life Extension of Structural Components in BWR ...............5401Young-Jin Kim, Peter L. Andresen
08589 - A Study on Localized Corrosion of Carbon Steel in Hanford Nuclear Wastes ..........................5413F. Gui, C.S. Brossia, J.A. Beavers, G. Frankel, G. Edgemon, H. Berman, L. Stock
08590 - General and Localized Corrosion of Borated Stainless Steels .....................................................5433T.E. Lister, R.E. Mizia, A.W. Erickson, B.S. Matteson
08591 - Effect of Metallurgical Factors on PWSCC Growth Rate of Ni-based Alloys............................5453N. Totsuka, T. Terachi, T. Yamada, M. Ozawa, K. Nakata
08592 - Corrosion Performance Comparison of Neutron Absorbing Alloys ...........................................5466R. E. Mizia, T. E. Lister, A. W. Erickson, T. L. Trowbridge
08593 - Electrochemical Studies on the Corrosion of Carbon Steel in Oxalic Acid Cleaning Solutions .........................................................................................................................................................5484
B. J. Wiersma, J. I. Mickalonis
08594 - In-situ Monitoring of Corrosion During a Laboratory Simulation of Oxalic Acid Chemical Cleaning ........................................................................................................................................5503
B. J. Wiersma, J. I. Mickalonis, D. C. Beam, M. R. Poirier, D. T. Herman, S. D. Fink, J. M. Pareizs, F. Fondeur
08595 - Current Corrosion Issues in Radioactive High Level Waste Tanks ............................................5529Karthik H. Subramanian, Bruce J. Wiersma, Philip E. Zapp
08596 - Effect of Grain Boundary Carbide on IGSCC Growth of Austenitic Stainless Steels in High-temperature Pure Water ................................................................................................................5552
T. Yamada, T. Terachi, K. Arioka
08597 - Development of a Corrosion-Resistant and Highly Weldable Filler Metal for Use with Alloy 690 ................................................................................................................................................5560
R.A. Etien III, G.A. Young, T.E. Capobianco, J.V. Mullen, S. Leveillee, P.C. Sander
08599 - Stress Corrosion Cracking of Carbon Steel in Nitrate and Carbonate Wastes at Hanford ......5583C.S. Brossia, J.A. Beavers, G. Frankel, G. Edgemon, H. Berman, C. Scott, K. Boomer
08600 - SCC Crack Growth in 316L Weld Metals in BWR Environments .............................................5597J. H. Kim, R. G. Ballinger. P. W. Stahle
08601 - Online Catalytic Mitigation of SCC at Parts Per Trillion Level..................................................5619P. Andresen, Y. Kim, T. Diaz, S. Hettiarachchi
08602 - Effects of Hydrogen on SCC Growth Rate of Ni Alloys ...............................................................5638P. Andresen, J. Hickling, A. Ahluwalia, J. Wilson
08603 - PWSCC Growth Rates of Alloy 690 and Its Weld Metals............................................................5658P. Andresen, J. Hickling, A. Ahluwalia, J. Wilson, M. Morra
08604 - Statistical Analysis on Stress Corrosion Cracking of Type 316L and Type 316 Stainless Steels in High Temperature Water ..............................................................................................5686
M. Mayuzumi, N. Ishiyama, K. Oonaka, Y. Mizutani, J-I. Tani
08605 - Spent Fuel Management at the Savannah River Site....................................................................5694P. R. Vormelker, R. L. Sindelar, R. Deible
08606 - Spent Nuclear Fuel Storage Basin Water Chemistry: Electrochemical Evaluation of Aluminum Corrosion................................................................................................................................5710
D.J. Hathcock, T.R. Murphy, P.R. Vormelker, S.P. Harris
08607 - A Coupled Multielectrode Array Sensor for Corrosion Monitoring at High Temperatures ................................................................................................................................................5716
Kuang-Tsan Chiang, Lietai Yang
08608 - Modeling the Effects of Nuclear Environments on Crevice Corrosion of Pure Nickel by Coupling of Phase and Polarization Behavior ...........................................................................5724
H. Hoffmeister
08613 - Electrochemical Corrosion Behavior of Friction Type Rock Bolt by Using Potentiodynamic and Potentiostatic Method ..............................................................................................5748
Md Sazzadur Rahman, Suresh Divi, Dhanesh Chandra, Jaak Daemen
08622 - Inhibition of Weld Corrosion in Flowing Brines Containing Carbon Dioxide ...........................5754K.Alawadhi, M.Robinson, A.Chalmers & I.G.Winning
08623 - Integrity Control in Heavily Fouled Systems - Phase II Environmentally Sustainable Solutions ....................................................................................................................................5768
D. Horsup, R. Meyer, L. Tiwari, T. Dunstan
08625 - Electrochemical Evaluation of CO2 Corrosion Inhibitors in High Turbulence Multiphase Fluid Flow ..................................................................................................................................5790
Q. Meng, V. Jovancicevic
08626 - Corrosion Inhibitor Qualification Testing for Subsea Wet Gas Pipelines ..................................5804Jorge L. Pacheco, Tim G. Martin, Jonathan Regina, Phil I. Abrams, Scott Hickman, Larry Talley
08627 - Important Considerations for Corrosion Inhibitors in the Laboratory and in the Prediction of Field Performance Based on Laboratory Data ....................................................................5819
Sunder Ramachandran, Keith Bartrip, Sebastian Mancuso, Paul Hammonds
Volume 9 08629 - Rotating Cylinder Electrode (RCE) Simulation of Corrosion in Sweet Production ..................5828
E. Wright, K. Efird, J. Boros, T. Hailey
08630 - Novel Corrosion Inhibitor for High Density ZnBr2 Completion Brines at High Temperatures ................................................................................................................................................5849
Mingjie Ke, Richard F. Stevens, Qi Qu
08632 - CO2 Corrosion Inhibitor Performance in the Presence of Solids: Test Method Development ..................................................................................................................................................5858
A. Pedersen, K. Bilkova, E. Gulbrandsen, J. Kvarekval
08634 - Materials and Corrosion History with Labarge Madison Production: A 20-Year Story Of Success ............................................................................................................................................5887
T. Martin, S.N. Smith, J. Bondos
08637 - Corrosion of Mild Steel in the Presence of Elemental Sulfur.......................................................5902H. Fang, D. Young, S. Nešic
08638 - Flow-dependency of Sweet and Sour Corrosion of Carbon Steel Downhole Production Tubing in Khuff-gas Wells .......................................................................................................5916
H.J. Choi, H.A. Al-Ajwad
08641 - Managing Corrosion in Sour Gas Systems: Testing, Design, Implementation and Field Experience ............................................................................................................................................5927
S. Kapusta, D. Raghu, J. Richard
08642 - Applications of Internal Corrosion Predictive Modeling (ICPM) in 2 or 3 - Phase Petroleum Pipelines: Model Validation.......................................................................................................5939
P. Teevens, K. Sand
08643 - How to Design Corrosion Inhibition Systems for Sour Wet Gas Service....................................5961L. Rippon, K. Welsh, M. Thompson
08644 - Corrosion and Inhibition Study for a H2S Containing Water Injection System: A Field Investigation Using Electrochemical Techniques .............................................................................5980
H. Wang, D. Fell, S. Bailey
08649 - Development and Field Deployment of a Novel Acidic Triethylene Glycol Buffer Chemical for Bringing Gas Dehydrators Back Into Specification ............................................................6000
J. Wylde, A. Duthie
08651 - The Investigation of Microbial Activity in an Offshore Oil Production Pipeline System and the Development of Strategies to Manage the Potential for Microbially Influenced Corrosion .......................................................................................................................................................6010
Peter Allison, Raja Nor Rafidah Raja Sahar, Ong Hock Guan, Tan Swee Hain, Ian Vance, Mike Thompson
08652 - Molecular Identification of MIC Bacteria from Scale and Produced Water: Similarities and Differences..........................................................................................................................6027
J. Larsen, T. Skovhus, A. Saunders, B. Højris, M. Agerbæk
08653 - Gene Array Analysis of Sulfate-Reducing Bacteria Grown on an Iron Electrode Under Conditions of Cathodic Protection ...................................................................................................6048
S. M. Caffrey, H.-S. Park, G. Voordouw, J. Been
08655 - Advantages and Limitations of Using Field Test Kits for Determining Bacterial Proliferation in Oil Field Waters .................................................................................................................6060
S. Al-Sulaiman, A. Al-Mithin, G. Murray, A. Biedermann, M. Islam
08656 - ASulfide Oxidase Biosensor for Monitoring Sulfide .....................................................................6078Reeta Sooknah, Sankara Papavinasam, R. Winston Revie
08658 - Use of Microbiocides in Barnett Shale Gas Well Fracturing Fluids to Control Bacteria Related Problems ...........................................................................................................................6086
J. Fichter, K. Johnson, K. French, R. Oden
08659 - THPS: A Holistic Approach to Treating Sour Systems ................................................................6100C.R.Jones , G.R. Collins, B.L.Downward, K. Hernandez
08660 - A New High Performance Quaternary Phosphonium Biocide for Microbiological Control in Oilfield Water Systems...............................................................................................................6114
Jeffrey F. Kramer, Frank O’Brien, Steven F. Strba
08662 - Sulfur Production Associated with Souring Control by Nitrate Injection: A Potential Corrosion Risk? ............................................................................................................................6128
S. Lin, G. Voordouw, D. Coombe
08663 - Laboratory Studies of Microbicide and Nitrate Strategies for MIC and Reservoir Souring Mitigation ........................................................................................................................................6139
S. Maxwell1, G. MacKenzie, C. Kuijvenhoven, B. Lomans, T. Granli
08667 - Corrosion and Erosion Resistant Polymer Composite Pipe for Oil Sands Hydrotransport .....6151P. Mertiny, K. Juss, T. Bell
08668 - Effects of Slurry pH on the Surface Mechanical Properties and Erosion-Corrosion Resistance.......................................................................................................................................................6159
Baotong Lu, Ke Wang, Xuemei Wan, Jingli Luo
08669 - Characterization of the Corrosion Mechanisms of PTA Coatings for Application in the Oilsands Industry....................................................................................................................................6170
J. F. Flores, A. Neville, N. Kapur, A Gnanavelu
08670 - Delayed Coker Furnace Fouling Control - Laboratory Correlation to Field Experience .........6185P. Eaton, J. Williams
08672 - Development of an Equipment Integrity Management System for the Long Lake SAGD Commercial Facility..........................................................................................................................6192
D. Foley, R. Goodfellow
08674 - Modern Packaging Materials for Electronic Equipment: Biodegradable and Vapor Phase Corrosion Inhibitor Treated..............................................................................................................6218
B. Miksic, B. Berg, B. Boyle
08675 - Severity of Stress Corrosion Cracks in Pipelines - Categories and Responses ...........................6226A. Batte, R. Fessler, S. Rapp
08676 - SCC Initiation in Alloy 600 Heat Affected Zones Exposed to High Temperature Water .........6236Edward Richey, David S. Morton, Robert A. Etien, George A. Young, Ronald Bucinell
08677 - Corrosion Issues in the French High-Level Nuclear Waste Program .........................................6258D. Feron, D. Crusset, J-M. Gras
08678 - History and Operation of the Hanford High-Level Waste Storage Tanks .................................6272G. Edgemon, V. Anda, H. Berman, M. Johnson, K. Boomer
08679 - MIC of Nuclear Waste Containers .................................................................................................6343Fraser King
08680 - Assessment of Corrosion-Based Failure in Stainless Steel Containers for the Long-Term Storage of Plutonium Base Salts ..................................................................................................................6381
R.S. Lillard, D.G. Kolman, M.A. Hill, M.B. Prime, D.K. Veirs, L.A. Worl
08681 - Initiation and Propagation of Stress Corrosion Cracking of Stainless-Steel Canister for Concrete Cask Storage of Spent Fuel ....................................................................................6403
J. Tani, M. Mayuzumi, N. Hara
08682 - Corrosion Testing of Nickel and Titanium Alloys for Nuclear Waste Disposition.....................6414R. Rebak
08683 - Used Fuel and Uranium Dioxide.....................................................................................................6441D.W. Shoesmith
08684 - A Sampling Method and Data Evaluation of Archeological Samples to Support Long-Term Corrosion Prediction ................................................................................................................6497
H. Yoshikawa, T. Matsui
08685 - The Corrosion Behavior of Carbon Steel Radioactive Waste Packages: A Summary Review of Swedish and U.K. Research ......................................................................................6507
Nicholas Smart
08686 - Corrosion Issues Related to Disposal of High-Level Nuclear Waste in the Yucca Mountain Repository ....................................................................................................................................6541
D. Duquette, R. Latanision, C. DiBella, B. Kirstein
Author Index
Recommended