View
4
Download
0
Category
Preview:
Citation preview
Components and Installation – Safety -Installation Equipment – Intertek Semko AB -1003 ANNEX 2B Laboratory accreditation Page 1 (13) 2015-02-16 2014/9 Flexible scope Limited to introduce new issues of the standards and amendments within the scope of accreditation
Standard designation SS/ SEMKO EN or HD Dop/Dow
IEC Publ Comments
Mini-Couplers for the interconnection of electrical mains supplied equipment in road vehicles
SS-EN 50 066:1992
Flat non-wirable two-pole plugs 2,5A 250V for class II-equipment
SS-EN 50075:1991/T1:2000 EN 50 075:1990/T1:2000
Cable trunking and ducting systems for electrical installations
SS-EN 50085-1:1997/A1:1998
SS-EN 50085-1:2005 Cable trunking systems and cable ducting systems intended for mounting on walls and ceilings
SS-EN 50085-2-1:2006
Cable trunking systems and cable ducting systems intended for mounting underfloor, flushfloor, or onfloor
SS-EN 50085-2-2, utg 1:2008
Part 2-2 Flowing mixed gas corrosion IEC 60068-2-60 missing
Service poles and services posts SS-EN 50085-2-4, utg 1:2009 EN 50085-2-4:2009
Part 2-4 Flowing mixed gas corrosion IEC 60068-2-60 missing
Conversion adapters for industrial use SS-EN 50250:2003/C1:2007 EN 50250:2002/C1:2007
Metric cable glands for electrical installations
SS-EN 50262:1999/A2:2005 EN 50262:1998/A2:2004
Cable cleats for electrical installations SS-EN 50368:2003 Miniature fuses Max test current 500A AC and
100A DC. Subcontractor used for all higher currents including short circuit tests
Part 1: Definitions and requirements SS-EN 60127-1:2006/A1:2011 EN 60127-1:2006/A1:2011
IEC 60127-1:2006 A1:2011
Supersedes EN 60127-1:1991+A1:1999+A2:2003
Part 2: Cartridge fuse-links SS-EN 60127-2:2003 / A1:2003 / A2:2010
IEC 60 127-2:2003 A1:2003 / A2:2010
Part 3: Sub-miniature fuse links SS-EN 60127-3:1996/A2:2003
IEC 60127-3:1988 / A2:2002
Part 4: Universal Modular Fuses-Links (UMF)
SS-EN 60127-4:2005/A1:2009/ A2:2013
IEC 60127-4:2005/ A1:2008/A2:2012
Part 6: Fuse-holders for miniature cartridge fuse-links
SS-EN 60127-6:1994/A1:1996 /A2:2003
IEC 60 127-6:1994 A1:1996/A2:2002
Part 7: Miniature fuse-links for special applications
SS-EN 60127-7:2013 IEC 60127-7:2013
Components and Installation – Safety -Installation Equipment – Intertek Semko AB -1003 ANNEX 2B Laboratory accreditation Page 2 (13) 2015-02-16 2014/9 Flexible scope Limited to introduce new issues of the standards and amendments within the scope of accreditation
Standard designation SS/ SEMKO EN or HD Dop/Dow
IEC Publ Comments
Safety of machinery - Electrical equipment of machines - Part 1: General requirements
SS-EN 60204-1:2007/A1:2009
IEC 60204-1:2005 A1:2008
Only clauses §4 – 15 Limited to products within standard IEC/EN 61400-2 for Small wind turbines.
Measuring relays and protection equipment
Part 27: Product safety requirements SS-EN 60255-27:2006 EN 60255-27:2005
IEC 60255-27:2005
Part 151: Functional requirements for over/under current protection
SS-EN 60255-151:2010 IEC 60255-151:2009
Low-voltage fuses Max test current 500A AC and 100A DC. Subcontractor used for all higher currents including short circuit tests
Part1: General requirements SS-EN 60269-1:2008/A1:2009 EN 60269-1:2007/A1:2009
IEC 60269-1:2006/ A1:2009
Supersedes EN 60269-1:1998+A1:2005 Partially supersedes EN 60269-2:1995+A1:1998+A2:2002 and EN 60269-3:1995+A1:2003
Part 2: Supplementary requirements for fuses for use by authorized persons (fuses mainly for industrial application)
SS-EN 60269-2:1995/A1:1999 /A2:2002
IEC 60269-2:1986 /A1:1995/A2:2002
Part 3: Supplementary requirements for fuses for use by unskilled persons (fuses mainly for household and similar applications)
SS-EN 60269-3:1995/A1:2003
IEC 60269-3:1987 /A1:2003
SS 428 05 39:2011/T1:2013 HD 60269-3:2010/A1:2013
IEC 60269-3:2010 /A1:2013
Supersedes HD 60269-3:2007
Plugs, socket-outlets and couplers for industrial purposes
Part 1: General requirements SS-EN 60309-1:1999/A1:2007 /A2:2012
IEC 60309-1:1999 /A1:2005/A2:2012
Part 2: Dimensional interchangeability requirements for pin and contact-tube accessories
SS-EN 60309-2:1999 /A1:2007/A2:2012
IEC 60309-2:1999 /A1:2005/A2:2012
1000V, 800A.
Part 4: Switched socket-outlets and connectors, with or without interlock
SS-EN 60309-4:2007/A1:2012
IEC 60309-4:2006 /A1:2012
1000V, 800A.
Appliance couplers for household and similar general purposes
Part 1: General requirements SS-EN 60320-1:2001/A1:2007
IEC 60320-1:2001 /A1:2007
Components and Installation – Safety -Installation Equipment – Intertek Semko AB -1003 ANNEX 2B Laboratory accreditation Page 3 (13) 2015-02-16 2014/9 Flexible scope Limited to introduce new issues of the standards and amendments within the scope of accreditation
Standard designation SS/ SEMKO EN or HD Dop/Dow
IEC Publ Comments
Part 2-1: Sewing machine couplers SS-EN 60320-2-1:2001 IEC 60320-2-1:2000 Part 2-2: Interconnection couplers for household and similar equipment
SS-EN 60320-2-2:1999 EN 60320-2-2:1998
IEC 60320-2-2:1998
EN 60 320-2-2:1991 IEC 60 320-2-2:1990/A1:1994/A2:1997
Del 2-3: Apparatanslutningsdon med kapslingsklass högre än IPX0
SS-EN 60320-2-3:1999 /A1:2005 EN 60320-2-3:1998/A1:2005
IEC 60320-2-3:1998 /A1:2004
Part 2-4: Appliance couplers dependent on appliance weight for engagement
SS-EN 60320-2-4:2006 /A1:2010
IEC 60320-2-4:2005 /A1:2009
Low-voltage switchgear and control-gear assemblies
Max test current 500A AC and 100A DC. Subcontractor used for all higher currents including short circuit tests
Part 1: Type-tested and partially type-tested assemblies
SS-EN 60439-1:2004 EN 60439-1:1999
IEC 60439-1:1999
Part 2: Particular requirements for busbar trunking systems (busways)
SS-EN 60439-2:2000/A1:2005
IEC 60439-2:2000 A1:2005
Clauses 8.2.14 and 8.2.15 excluded
Part 3: Particular requirements for low-voltage switchgear and controlgear assemblies intended to be installed in places where unskilled persons have access for their use - Distribution boards
SS-EN 60439-3:1991/A1:1994 /A2:2001/C2:2006/C3:2010 EN 60439-3:1991/C2:2005 /C3:2009
IEC 60439-3:1990 /A1:1993/A2:2001
Part 4: Particular requirements for assemblies for construction sites (ACS)
SS-EN 60439-4:2005 IEC 60439-4:2004
Part 5: Particular requirements for assemblies for power distribution in public networks
SS-EN 60439-5:2006 IEC 60439-5:2006 Clauses 8.2.3, 8.2.4.2. 8.2.9 and 8.2.11 excluded
Switches for household and similar fixed electrical installations
Part 1: General requirements SS-EN 60669-1:2000/A1:2002 /A2:2008/C1:2007/C1:2007/IS1:2009 EN 60669-1:1999/A1:2002 /A2:2008/C1:2007/IS1:2009
IEC 60 669-1:1998 /A1:1999/A2:2006
Components and Installation – Safety -Installation Equipment – Intertek Semko AB -1003 ANNEX 2B Laboratory accreditation Page 4 (13) 2015-02-16 2014/9 Flexible scope Limited to introduce new issues of the standards and amendments within the scope of accreditation
Standard designation SS/ SEMKO EN or HD Dop/Dow
IEC Publ Comments
Part 2-1: Particular requirements - Section 1: Electronic switches
SS-EN 60669-2-1:2005 /A1:2009/A12:2010/C1:2008 EN 60669-2-1:2004 /A1:2009/A12:2010/C1:2007
IEC 60 669-2-1:2002 A1:2008
Part 2-2: Particular requirements - Electromagnetic remote-control switches (RCS)
SS-EN 60669-2-2:2006
IEC 60 669-2-2:2006
Part 2-3: Particular requirements - Time-delay switches (TDS)
SS-EN 60669-2-3:2006 IEC 60669-2-3:2006
Part 2-4: Particular requirements - Isolating switches
SS-EN 60669-2-4:2005 IEC 60669-2-4:2004
Part 2-6: Particular requirements - Fireman's switches for exterior and interior signs and luminaires
SS-EN 60669-2-6:2012 IEC 60669-2-6:2012
Boxes and enclosures for electrical accessories for household and similar fixed electrical installations
Part 1: General requirements SS-EN 60670-1:2005/A1:2013 /C1:2007/C2:2010/IS1:2009
IEC 60670-1:2002 /A1:2011
Part 21: Particular requirements for boxes and enclosures with provision for suspension means
SS-EN 60670-21:2007 IEC 60670-21:2004
Part 2-22: Particular requirements for connecting boxes and enclosures
SS-EN 60670-22:2007 IEC 60670-22:2003
Part 23: Particular requirements for floor boxes and enclosures
SS-EN 60670-23:2009 IEC 60670-23:2006
Automatic electrical controls for household and similar use
Part 1: General requirements SS-EN 60730-1:1995 /A1:1997/A2:1998/A11:1996 /A12:1996/A14:1998/A15:1998 /A16:1999/A17:2000/A18:2003 /C2:2007
IEC 60730-1:1993 A1:1994 A2:1997
Type I only. Clause H.11.12 excluded
Components and Installation – Safety -Installation Equipment – Intertek Semko AB -1003 ANNEX 2B Laboratory accreditation Page 5 (13) 2015-02-16 2014/9 Flexible scope Limited to introduce new issues of the standards and amendments within the scope of accreditation
Standard designation SS/ SEMKO EN or HD Dop/Dow
IEC Publ Comments
Part 1: General requirements SS-EN 60730-1:2001/A1:2005 /A2:2009/A11:2002/A12:2003 /A13:2004/A14:2005/A16:2007 C1:2007/C1:2010 EN 60730-1:2000 /A12:2003/A1:2004/A13:2004/A14:2005/A15:2007/A16:2007/A17:2000/A18:2003/A2:2008
IEC 60 730-1:1999 A1:2003/A2:2007
Part 1: General requirements SS-EN 60730-1:2012 EN 60730-1:2011
IEC 60730-1:2010
Part 2-2: Particular requirements for thermal motor protectors
SS-EN 60730-2-2:2002 /A1:2006/A11:2005
IEC 60730-2-2:2001 A1:2005
Part 2-3: Particular requirements for thermal protectors for ballasts for tubular fluorescent lamps
SS-EN 60730-2-3:2008 EN 60730-2-3:2007
IEC 60730-2-3:2006
Part 2-4: Particular requirements for thermal motor protectors for motor-compressors of hermetic and semi-hermetic type
SS-EN 60730-2-4:2008 EN 60730-2-4:2007
IEC 60730-2-4:2006
Part 2-5: Particular requirements for automatic electrical burner control systems
SS-EN 60730-2-5:2002 /A1:2005/A11:2005/A2:2010
IEC 60730-2-5:2000 /A1:2004/A2:2008
Part 2-6: Particular requirements for automatic electrical pressure sensing controls including mechanical requirements
SS-EN 60730-2-6:2009 EN 60 730-2-6:2008
IEC 60730-2-6:2007
Part 2-7: Particular requirements for timers and time switches
SS-EN 60730-2-7:2010 /AC1:2012 EN 60730-2-7:2010/AC:2011
IEC 60730-2-7:2008
Part 2-8: Particular requirements for electrically operated water valves, including mechanical requirements
SS-EN 60730-2-8:2002 /A1:2003 EN 60730-2-8:2002/A1:2003
IEC 60730-2-8:2000 /A1:2002
Part 2-9: Particular requirements for temperature sensing controls
SS-EN 60730-2-9:2011 EN 60730-2-9:2010
IEC 60730-2-9:2008
Part 2-10: Particular requirements for motor starting relays
SS-EN 60730-2-10:2008 EN 60730-2-10:2007
IEC 60730-2-10:2006
Part 2-11: Particular requirements for energy regulators (23p)
SS-EN 60730-2-11:2008 EN 60730-2-11:2008
IEC 60730-2-11:2006
Components and Installation – Safety -Installation Equipment – Intertek Semko AB -1003 ANNEX 2B Laboratory accreditation Page 6 (13) 2015-02-16 2014/9 Flexible scope Limited to introduce new issues of the standards and amendments within the scope of accreditation
Standard designation SS/ SEMKO EN or HD Dop/Dow
IEC Publ Comments
Part 2-12: Particular requirements for electrically operated door locks
SS-EN 60730-2-12:2006 /A11:2009 EN 60730-2-12:2006/A11:2008
IEC 60730-2-12:2005
Part 2-13: Particular requirements for humidity sensing controls
SS-EN 60730-2-13:2008 EN 60730-2-13:2008
IEC 60730-2-13:2006
Part 2-14: Particular requirements for electric actuators
SS-EN 60730-2-14:1998 /A1:2001/A11:2005/A2:2009 EN 60730-2-14:1997 A1:2001/A11:2005/A2:2008
IEC 60730-2-14:1995 A1:2001/A2:2007
Part 2-15: Particular requirements for automatic electrical water level sensing controls of the float or electrode sensor type used in boiler applications
SS-EN 60730-2-15:2010 EN 60730-2-15:2010
IEC 60730-2-15:2008
Part 2-16: Particular requirements for automatic electrical water level operating controls of the float type for household and similar applications
Replaced by EN 60730-2-15
Replaced by IEC 60730-2-15
Electrical accessories - Cord sets and interconnection cord sets
SS-EN 60799:1999 EN 60799:1998
IEC 60799:1998
Plugs and socket-outlets for household and similar purposes
Part 1: General requirements SS IEC 60884-1:2004 SS 428 08 34:2004
IEC 60884-1:2002 A1:2006
Part 1: General requirements SS-IEC 60884-1:2013 SS 428 08 34:2013
IEC 60884-1:2013
Danish deviations DS 60 884-2-D1:2011 Afsnit 107-2-D1:2008 edition 5
French deviations NF C 61-314_2003+A1(2010) German deviations DIN/VDE 0620-1:2010 Part 2-1: Particular requirements for fused plugs
IEC 60884-2-1:2006
Part 2-2: Particular requirements for socket-outlets for appliances
SS 428 08 68:1999/T1:2000 IEC 60884-2-2:2006
Part 2-3: Particular requirements for switched socket-outlets without interlock for fixed installations
IEC 60884-2-3:2006
Part 2-4: Particular requirements for plugs and socket-outlets for SELV
IEC 60884-2-4:2007
Part 2-5: Particular requirements for ADAPTORS
IEC 60884-2-5:1995
Components and Installation – Safety -Installation Equipment – Intertek Semko AB -1003 ANNEX 2B Laboratory accreditation Page 7 (13) 2015-02-16 2014/9 Flexible scope Limited to introduce new issues of the standards and amendments within the scope of accreditation
Standard designation SS/ SEMKO EN or HD Dop/Dow
IEC Publ Comments
Part 2-6: Particular requirements for switched socket-outlets with interlock for fixed installations
IEC 60884-2-6:1997
Part 2-7: Particular requirements for cord extension sets
SS-IEC 60884-2-7:2013 IEC 60884-2-7:2011
Electrical accessories - Circuit breakers for overcurrent protection for household and similar installations
Max test current 500A AC and 100A DC. Subcontractor used for all higher currents including short circuit tests Tillägg av energiklassning upp till 63A (tidigare max 32A)
Part 1: Circuit-breakers for a.c. operation
SS-EN 60898-1:2003 /A1:2004/A11:2005/A12:2008 /A13:2012/C1:2004 /IS1:2008/IS2:2008/IS3:2008 /IS4:2008
IEC 60898-1:2002 A1:2002/A2:2003
Part 2: Circuit-breakers for a.c. and d.c. operation
SS-EN 60898-2:2006 IEC 60898-2:2000 A1:2003
Circuit-breakers for equipment (CBE) SS-EN 60934:2001 /A1:2007/A2:2013
IEC 60934:2000 /A1:2007/A2:2013
Max test current 500A AC and 100A DC. Subcontractor used for all higher currents including short circuit tests
Low-voltage switchgear and controlgear Max test current 500A AC and 100A DC. Subcontractor used for all higher currents including short circuit tests
Part 1: General rules SS-EN 60947-1:2008/A1:2011
IEC 60947-1:2007 A1:2010
Part 2: Circuit-breakers SS-EN 60947-2:2006 /A1:2009/A2:2013
IEC 60947-2:2006 /A1:2009/A2:2013
Part 3: Switches, disconnectors, switch disconnectors and fuse-combination units
SS-EN 60947-3:2009/A1:2012
IEC 60 947-3:2008 A1:2011/C1:2012
Part 4-1: Contactors and motor-starters - Section One: Electromechanical contactors and motor-starters
SS-EN 60947-4-3:2010 /A1:2012
IEC 60947-4-1:2009 A1:2012
Part 4-2: Contactors and motor-starters - AC semiconductor motor controllers and starters
SS-EN 60947-4-2:2012 IEC 60 947-4-2:2011 C1:2012
Part 4-3: Contactors and motor-starters - AC semiconductor controllers and contactors for non-motor loads
SS-EN 60947-4-3:2000 A1:2007/A2:2012
IEC 60947-4-3:1999 C1:2000/A1:2006 A2:2011
Components and Installation – Safety -Installation Equipment – Intertek Semko AB -1003 ANNEX 2B Laboratory accreditation Page 8 (13) 2015-02-16 2014/9 Flexible scope Limited to introduce new issues of the standards and amendments within the scope of accreditation
Standard designation SS/ SEMKO EN or HD Dop/Dow
IEC Publ Comments
Part 5-1: Control circuit devices and switching elements - Electromechanical control circuit devices
SS-EN 60947-5-1:2004 /A1:2009
IEC 60947-5-1:2003 A1:2009
Part 5-2: Control circuit devices and switching elements - Proximity switches
SS-EN 60947-5-2:2008 /A1:2013 EN 60947-5-2:2007/A1:2012
IEC 60947-5-2:2007 /A1:2012
Part 5-3: Control circuit devices and switching elements - Requirements for proximity devices with defined behaviour under fault conditions (PDF)
SS-EN 60947-5-3:2014 IEC 60947-5-3:2013
Part 5-4: Control circuit devices and switching elements - Method of assessing the performance of low-energy contacts - Special tests
SS-EN 60947-5-4:2004 IEC 60947-5-4:2002
Part 5-5: Control circuit devices and switching elements - Electrical emergency stop device with mechanical latching function
SS-EN 60947-5-5:1998 /A1:2005/A11:2013
IEC 60947-5-5:1997 A1:2005
Part 5-8: Control circuit devices and switching elements - Three-position enabling switches
SS-EN 60947-5-8:2007 IEC 60947-5-8:2006
Part 6-2: Multiple function equipment - Control and protective switching devices (or equipment) (CPS)
SS-EN 60947-6-2:2003 /A1:2007
IEC 60947-6-2:2002 /A1:2007
Part 7-1: Ancillary equipment - Terminal blocks for copper conductors
SS-EN 60947-7-1:2009 IEC 60 947-7-1:2009
Part 7-2: Ancillary equipment - Protective conductor terminal blocks for copper conductors
SS-EN 60947-7-2:2009 IEC 60 947-7-2: 2009
Part 7-3: Ancillary equipment - Safety requirements for fuse terminal blocks
SS-EN 60947-7-3:2010 IEC 60 947-7-3: 2009
Connecting devices for low-voltage circuits for household and similar purposes
Max test current 500A AC and 100A DC. Subcontractor used for all higher currents including short circuit tests
Part 1: General requirements SS-EN 60998-1:2004 IEC 60998-1:2003 Part 2-1: Particular requirements for connecting devices as separate entities with screwtype clamping units
SS-EN 60998-2-1:2004 IEC 60998-2-1:2003
Part 2-2: Particular requirements for connecting devices as separate entities with screwless-type clamping units
SS-EN 60998-2-2:2004 IEC 60998-2-2:2003
Components and Installation – Safety -Installation Equipment – Intertek Semko AB -1003 ANNEX 2B Laboratory accreditation Page 9 (13) 2015-02-16 2014/9 Flexible scope Limited to introduce new issues of the standards and amendments within the scope of accreditation
Standard designation SS/ SEMKO EN or HD Dop/Dow
IEC Publ Comments
Part 2-3: Particular requirements for connecting devices as separate entities with insulation piercing clamping units
SS-EN 60998-2-3:2004 IEC 60998-2-3:2003
Part 2-4: Particular requirements for twist-on connecting devices
SS-EN 60998-2-4:2005 IEC 60998-2-4:2004
Connecting devices - Safety requirements for screw-type and screwless-type clamping units for electrical copper conductors
Part 1: General requirements and particular requirements for clamping units for conductors from 0,2 mm2 up to 35 mm2 (included)
SS-EN 60999-1:2000 IEC 60999-1:1999
Part 2: Particular requirements for clamping units for conductors above 35 mm2 up to 300 mm2 (included)
SS-EN 60999-2:2003 IEC 60999-2:2003
Residual current operated circuit-breakers without integral overcurrent protection for household and similar uses (RCCB's)
Part 1: General rules SS-EN 61008-1:2013 EN 61008-1:2012
IEC 61008-1:2010
Part 2-1: Applicability of the general rules to RCCBs functionally independent of line voltage
SS-EN 61008-2-1:1995 /A11:1998/C1:1999 EN 61008-2-1:1994 /A11:1998/C1:1999
IEC 61008-2-1:1990
Residual current operated circuit-breakers with integral overcurrent protection for household and similar uses (RCBO's
Part 1: General rules SS-EN 61009-1:2013 EN 61009-1:2012
IEC 61009-1:2010
Part 2-1: Applicability of the general rules to RCBOs functionally independent of line voltage
SS-EN 61009-2-1:1995 /A11:1998/C1:1999
IEC 61009-2-1:1991
Switches for appliances Part 1: General requirements SS-EN 61058-
1:2002/A2:2008 EN 61058-1:2002 (IEC A1 included) A2:2008
IEC 61058-1:2000 A1:2001/A2:2007
Part 2-1: Particular requirements for cord switches
SS-EN 61058-2-1:2011 IEC 61058-2-1:2010
Part 2-4: Particular requirements for independently mounted switches
SS-EN 61058-2-4:2007 EN 61058-2-4:2005
IEC 61058-2-4:1995 A1:2003
Components and Installation – Safety -Installation Equipment – Intertek Semko AB -1003 ANNEX 2B Laboratory accreditation Page 10 (13) 2015-02-16 2014/9 Flexible scope Limited to introduce new issues of the standards and amendments within the scope of accreditation
Standard designation SS/ SEMKO EN or HD Dop/Dow
IEC Publ Comments
Part 2-5: Particular requirements for change-over selectors
SS-EN 61058-2-5:2011 IEC 61058-2-5:2010
Cable trunking and ducting systems for electrical installations
Part 1: General Requirements IEC 61084-1:1991 A1:1993
Part 2-1: Cable trunking and ducting systems for mounting on walls or ceilings
IEC 61084-2-1:1996
Part 2-2: Particular requirements – Cable trunking systems and cablie ductiong systems intended for underfloor and flushfloor installations
IEC 61084-2-2:2003
Part 2-4: Particular Requirements – Service Poles
IEC 61084-2-4:1996
Electromechanical contactors for household and similar purposes
SS-EN 61095:2009 IEC 61095:2009
Electrical accessories - Cable reels for household and similar purposes
SS-EN 61242:1997 /A1:2008/C1:2011 EN 61242:1997/A11:2004 /A12:2005/A1:2008/Cor1:2011
IEC 61242:1995 A1:2008
Live working - Voltage detectors Part 3: Two-pole low-voltage type SS-EN 61243-3:2010 IEC 61243-3:2009 Industrial cable reels SS-EN 61316:2000 IEC 61316:1999 Conduit systems for cable management Max test current 500A AC and
100A DC. Subcontractor used for all higher currents including short circuit tests
Part 1: General requirements SS-EN 61386-1:2008 IEC 61386-1:2008 Part 21: Particular requirements - Rigid conduit systems
SS-EN 61386-1:2004/A11:2011
IEC 61386-21:2002
Part 22: Particular requirements - Pliable conduit systems
SS-EN 61386-2:2004/A11:2011
IEC 61386-22:2002
Part 23: Particular requirements - Flexible conduit systems
SS-EN 61386-23:2004/A11:2011
IEC 61386-23:2002
Low-voltage switchgear and controlgear assemblies
Max test current 500A AC and 100A DC. Subcontractor used for all higher currents including short circuit tests
Part 1: General rules SS-EN 61439-1:2010 /AC1:2013 SS-EN 61439-1:2012
IEC 61439-1:2009 IEC 61439-1:2011
Components and Installation – Safety -Installation Equipment – Intertek Semko AB -1003 ANNEX 2B Laboratory accreditation Page 11 (13) 2015-02-16 2014/9 Flexible scope Limited to introduce new issues of the standards and amendments within the scope of accreditation
Standard designation SS/ SEMKO EN or HD Dop/Dow
IEC Publ Comments
Part 2: Power switchgear and controlgear assemblies
SS-EN 61439-2:2010 SS-EN 61439-2:2012
IEC 61439-2:2009 IEC 61439-2:2011
Part 3: Distribution boards intended to be operated by ordinary persons (DBO)
SS-EN 61439-3:2012 IEC 61439-3:2012
Part 4: Particular requirements for assemblies for construction sites (ACS)
SS-EN 61439-4:2013 IEC 61439-4:2012
Part 5: Assemblies for power distribution in public networks
SS-EN 61439-5:2011 IEC 61439-5:2010
Part 6: Busbar trunking systems (busways)
SS-EN 61439-6:2012 IEC 61439-6:2012
Powertrack systems Part 1: General requirements SS-EN 61534-1:2003
SS-EN 61534-1:2011 IEC 61534-1:2003 IEC 61534-1:2011
Part 21: Particular requirements for powertrack systems intended for wall and ceiling mounting
SS-EN 61534-21:2006 IEC 61534-21:2006
Part 22: Particular requirements for powertrack systems intended for on floor or under floor installation
SS-EN 61534-22:2009 IEC 61534-22:2006
Installation couplers intended for permanent connection in fixed installations
SS-EN 61535:2009/A1:2013
IEC 61535:2009 A1:2012
For class II (max 3 kA) and class III (max 6.6 kV).
Cable management – Cable tray systems and cable ladder systems
SS-EN 61537:2007 IEC 61537:2006
Electrical accessories – Portable residual current devices without integral overcurrent protection for household and similar use (PRCDs)
HD 639 S1:2002 (SS 4280884:2002) A1:2003/A2:2010 T1:2003/T2:2011
IEC 61540:1997 A1:1998
Low-voltage surge protective devices Part 11: Surge protective devices connected to low-voltage power systems - Requirements and tests
SS-EN 61643-11:2013 EN 61643-11:2012
IEC 61643-11:2011
Part 21: Surge protective devices connected to telecommunications and signalling networks - Performance requirements and testing methods
SS-EN 61643-21:2002/A1:2009 /A2:2013
IEC 61643-21:2000 /A1:2008 /A2:2012
Part 321: Specifications for avalanche breakdown diode (ABD)
SS-EN 61643-321:2002 IEC 61643-321:2001
Part 341: Specification for thyristor surge suppressors (TSS)
SS-EN 61643-341:2002 IEC 61643-341:2001
Adjustable speed electrical power drive systems
Components and Installation – Safety -Installation Equipment – Intertek Semko AB -1003 ANNEX 2B Laboratory accreditation Page 12 (13) 2015-02-16 2014/9 Flexible scope Limited to introduce new issues of the standards and amendments within the scope of accreditation
Standard designation SS/ SEMKO EN or HD Dop/Dow
IEC Publ Comments
Part 1: General requirements - Rating specifications for low voltage adjustable speed d.c. power drive systems
SS-EN 61800-1:1998 IEC 61800-1:1997
Part 5-1: Safety requirements - Electrical, thermal and energy
SS-EN 61800-5-1:2007 IEC 61800-5-1:2007
Electromechanical elementary relays Part 1: General requirements SS-EN 61810-1, utg 3:2008 IEC 61810-1:2008 Part 5: Insulation coordination SS-EN 61810-5, utg 1:1999 IEC 61810-5:1998 Part 7: Test and measurement procedures
SS-EN 61810-7, utg 1:2006 IEC 61810-7:2007
Communication networks and systems in substations
Part 3: General requirements SS-EN 61850-3:2003 EN 61850-3:2002
IEC 61850-3:2002
Connectors - Safety requirements and tests
SS-EN 61984:2009 IEC 61984:2009
Devices for the connection of luminaires for household and similar purposes
Part 1: General requirements SS-EN 61995-1:2008 IEC 61995-1:2005 Part 2: Standard sheets for DCL SS-EN 61995-2:2009 IEC 61995-2:2009 Electrical accessories Circuit-breakers and similar equipment for household use - Auxiliary contact units
SS-EN 62019:1999 A1:2003/A11:2005
IEC 62019:1999 A1:2002
Indicator light units for household and similar fixed-electrical installations
Part 1: General requirements SS-EN 62094-1:2003/A11:2003
IEC 62094:2002
Empty enclosures for low-voltage switchgear and controlgear assemblies
General requirements SS-EN 62208:2012 EN 62208:2011
IEC 62208:2011
Cable management systems - Cable ties for electrical installations
SS-EN 62275:2009
IEC 62275:2006
Lamp connectors for general use SS 428 08 31-3ed / T1:1997 See also IEC/EN 61995 Cord sets - Rewirable cord sets - Safety requirements and test methods
SS 428 08 67:1989
Boxes for eletrical wiring Single and double box for flush type accessories - Dimensions
SS 430 06 17:2006
Circular junction box - Dimensions SS 430 06 18:2007
Components and Installation – Safety -Installation Equipment – Intertek Semko AB -1003 ANNEX 2B Laboratory accreditation Page 13 (13) 2015-02-16 2014/9 Flexible scope Limited to introduce new issues of the standards and amendments within the scope of accreditation
Standard designation SS/ SEMKO EN or HD Dop/Dow
IEC Publ Comments
Circular box for luminaires SS 430 06 19:2007 Rewireable cord sets SEMKO 107 – 1968 )
med ändring 1-4 (CEE 7)
CEE 7 1963 Mod 1 1972 Mod 2 1972 Mod 3 1974 Mod 4 1977
Latest changes are printed in extra bold type. The accreditation does not cover sampling activities. If the laboratory, regardless of this, performs the sampling by itself, then the testing is not considered to be performed under accreditation. Provtagning omfattas inte av ackrediteringen. Om laboratoriet ändå själv utför provtagning omfattas provningen inte av ackrediteringen. The accreditation does not cover opinions and interpretations. If the laboratory, regardless of this, expresses opinions and/or provides interpretations in the test report, then the testing is not considered to be performed under accreditation. Synpunkter och tolkningar omfattas inte av ackrediteringen. Om laboratoriet ändå redovisar synpunkter och tolkningar i provningsrapporten, omfattas provningen inte av ackrediteringen.
Recommended