View
232
Download
0
Category
Preview:
Citation preview
8/17/2019 CLUSTER - AIX - Installation de HACMP_eng
http://slidepdf.com/reader/full/cluster-aix-installation-de-hacmpeng 1/93
Project of Rationalization andConsolidation
SANOFI-AVENTIS
CLUSTER - AIX - Installation de HACMP_eng Technical paper 1193
Cluster PowerHA of SAP production
SANOFI-AVENTIS
Technical dossier of PowerHA 5.4 installation
____________________________________________________________________
Samir Attmani
E-mail: samir.attmani@fr.ibm.com
8/17/2019 CLUSTER - AIX - Installation de HACMP_eng
http://slidepdf.com/reader/full/cluster-aix-installation-de-hacmpeng 2/93
PowerHA 5.4 installation record
Technical dossier of PowerHA 5.4 installation
CLUSTER - AIX - Installation de HACMP_eng Technical paper 2293
Modifi cati ons History
Version Written by Contents V1.0 S.ATTMANI Document Creation
V1.1 S.ATTMANI Document Modification V1.2 S.ATTMANI Modification after feedback V1.3 Mr. Lescot Upgraded for second cluster (SMART)
Vali dati ons Hi story
Version Examined by Approval
Remarks Approval by Date V1.1 Michael LESCOT
V1.3 Michael LESCOT
Maili ng li st
Recipient Organization/Jobfunction
Objective of the spreading
(val idation/inform ation )
Michael LESCOT Responsible sanofi-aventisAdministration Virtualization
validation
Pierjean Ponenti Ph. D IBM Project director information Patrice Calatrava IBM ITSpecialist information
Reference documents:
Document description
8/17/2019 CLUSTER - AIX - Installation de HACMP_eng
http://slidepdf.com/reader/full/cluster-aix-installation-de-hacmpeng 3/93
PowerHA 5.4 installation record
Technical dossier of PowerHA 5.4 installation
CLUSTER - AIX - Installation de HACMP_eng Technical paper 3393
Contents
INTRODUCTION ............................................................................................................................. 4
DESCRIPTION OF THE PLATFORM ......................................................................................... 5
1 EQUIPMENT ........................................................................ERROR ! BOOKMARK NOT DEFINED. 2 ARCHITECTURE: .................................................................ERROR ! BOOKMARK NOT DEFINED.
3 VERSION OF THE PRODUCTS ...............................................ERROR ! BOOKMARK NOT DEFINED.
IMPLEMENTATION OF POWERHA .......................................................................................... 7
4 FILESETS PRE-REQUISITE FOR POWERHA ........................ERROR ! BOOKMARK NOT DEFINED. 4.1 RSCT................................................................................Er ror! Bookmark not defi ned. 4.2 The filesets prerequisite has the installation of POWERHA 5.4 were installed: ....Error!
Bookmark not defi ned. 5 I NSTALLATION OF THE FILESETS POWERHA 5.4...............ERROR ! BOOKMARK NOT DEFINED.
6 CHECKING OF THENECESSARY ONE ........................................................................................ 106.1 Pre-requisite TCPIP........................................................ Er ror! Bookmark not defi ned. 6.2 File netmon.cf ..................................................................Er ror! Bookmark not defi ned.
6.3 Checking of the parameters systems ............................... Er ror! Bookmark not defi ned. 6.4 Principles of organization of the VG, VL and FS for POWERHAEr ror! Bookmark not
defined. 6.5 Creation of the repertoire POWERHA............................Er ror! Bookmark not defi ned. 6.6 Topology .......................................................................... Er ror! Bookmark not defi ned.
6.7 Resources discs POWERHA............................................Er ror! Bookmark not defi ned. 6.8 Components of the groups of resource............................ Er ror! Bookmark not defi ned.
7 DEFINITION OF LOGICAL VOLUMES AND THE FILESYSTEMSERROR ! BOOKMARK NOT
DEFINED. 7.1 Volume Logical creation of log .......................................Er ror! Bookmark not defi ned.
7.2 Creation of logical volumes ............................................ Er ror! Bookmark not defi ned. 7.3 Creation of the filesystems ..............................................Er ror! Bookmark not defi ned.
7.4 Enlarging of the filesystem to the desired size ................Er ror! Bookmark not defi ned. 8 NOTIFICATION OF THE ERRORS ...........................................ERROR ! BOOKMARK NOT DEFINED.
8.1 Unattended setup of the notification of errors ................Er ror! Bookmark not defi ned.
8.2 Addition of a notification................................................. Er ror! Bookmark not defi ned. 8.3 List supervised errors: .................................................................................................. 36
9 TUNING OF THE CLUSTER ....................................................ERROR ! BOOKMARK NOT DEFINED. 10 POWERHA SPIN COLLECTION MANAGEMENT .............ERROR ! BOOKMARK NOT DEFINED.
10.1 Administration .................................................................Er ror! Bookmark not defi ned.
10.2 Creation of a new “File Collection”...............................Er ror! Bookmark not defi ned.
11 APPENDICES ....................................................................................................................... 4511.1 ANNEXURE : Launching and Shutdown of the cluster .............................................. 45 11.2 ANNEXURE : Logfiles of POWERHA ......................................................................... 46
8/17/2019 CLUSTER - AIX - Installation de HACMP_eng
http://slidepdf.com/reader/full/cluster-aix-installation-de-hacmpeng 4/93
PowerHA 5.4 installation record
Technical dossier of PowerHA 5.4 installation
CLUSTER - AIX - Installation de HACMP_eng Technical paper 4493
11.3 ANNEXURE : Script.......................................................Er ror! Bookmark not defi ned.
11.4 ANNEXURE : Snap ...................................................................................................... 49
8/17/2019 CLUSTER - AIX - Installation de HACMP_eng
http://slidepdf.com/reader/full/cluster-aix-installation-de-hacmpeng 5/93
8/17/2019 CLUSTER - AIX - Installation de HACMP_eng
http://slidepdf.com/reader/full/cluster-aix-installation-de-hacmpeng 6/93
PowerHA 5.4 installation record
Technical dossier of PowerHA 5.4 installation
CLUSTER - AIX - Installation de HACMP_eng Technical paper 6693
Description of the platform
1 Equipment
The cluster of POWERHA production consists of two P570 servers.
The berry of discs shared is of the DS8000 type.
2 Architecture:
gtyxvio1p02 gtyxvio2p02
SAN
rootvg
VGCL_PM6log VGCL_PM6redo
VGCL_PM6dat1 VGCL_PM6dat2
VGCL_PM6dat3
en0
virtual
N
P
I
V
rootvg
VGCL_PM6log VGCL_PM6redo
VGCL_PM6dat1 VGCL_PM6dat2
VGCL_PM6dat3
gtyxvio1p03 gtyxvio2p03
v s c s i
v s c s i
v s c s i
v s c s i
vlan16
gtyxsappm6p1 gtyxsappm6p2
en0
virtual
e
n
t0
e
n
t3
e
n
t2
e
n
t1
e
n
t0
e
n
t3
e
n
t2
e
n
t1
en
t
0
en
t
3
en
t
2
en
t
1
e
n
t0
e
n
t3
e
n
t2
e
n
t1
802.3ad 802.3ad 802.3ad 802.3ad
N
P
I
V
N
P
I
V
N
P
I
V
N
P
I
V
N
P
I
V
N
P
I
V
N
P
I
V
Figure1: Structure of PowerHA
8/17/2019 CLUSTER - AIX - Installation de HACMP_eng
http://slidepdf.com/reader/full/cluster-aix-installation-de-hacmpeng 7/93
PowerHA 5.4 installation record
Technical dossier of PowerHA 5.4 installation
CLUSTER - AIX - Installation de HACMP_eng Technical paper 7793
3 Version of the products
AIX version: 6.1 - TL04 (6100-04-03-1009)
Version POWERHA: 5.4 (cluster.es.se 5.4.1.8 rver. rte)
Version SD DPCM:
2.5.1.0 devices. sddpcm.61. rte
devices.fcp.disk.ibm.mpio 1.0.0.20
8/17/2019 CLUSTER - AIX - Installation de HACMP_eng
http://slidepdf.com/reader/full/cluster-aix-installation-de-hacmpeng 8/93
PowerHA 5.4 installation record
Technical dossier of PowerHA 5.4 installation
CLUSTER - AIX - Installation de HACMP_eng Technical paper 8893
Implementation of POWERHAThe implementation of the cluster POWERHA breaks up into 4 principal stages:
- Required pre Filesets,- Checking of the AIX prerequisites,
- Configuration of the cluster POWERHA- Installation of the notification of errors
4 Filesets pre-requisite for POWERHA
4.1 RSCT
NB: filesets minimum, versions to be upgraded according to AIX6.1 TL4 SP3 and PowerHA
5.4.1 SP8
Fileset Version Description
rsct.basic.hacmp 2.5.3.0 RSCT BASIC Function (HACMP/ES Support)
rsct. basic. rte 2.5.3.0 RSCT BASIC Function
rsct.basic.sp 2.5.3.0
rsct.compat.basic.hacmp 2.5.3.0 RSCT Vent Management BASIC Function (HACMP/ES Support)
rsct. compat. basic. rte 2.5.3.0 RSCT Vent Management BASIC Function
rsct.compat.basic.sp 2.5.3.0
rsct.compat.clients.hacmp 2.5.3.0 RSCT Vent Management User Function (HACMP/ES Support)
rsct. compat. clients. rte 2.5.3.0 RSCT Vent Management User Function
rsct.compat.clients.sp 2.5.3.0
rsct.core.auditrm 2.5.3.0 RSCT To that the Log Resource Manager rsct.core.errm 2.5.3.0 RSCT Vent Talkback Resource Manager
rsct.core.fsrm 2.5.3.0 RSCT Spins System Resource Manager
rsct.core.gui 2.5.3.0 RSCT Graphical To use Application interface
rsct.core.hostrm 2.5.3.0 RSCT Host Resource Manager
rsct.core.lprm 2.5.3.0 RSCT Least Privilege Resource Manager
rsct.core.rmc 2.5.3.0 RSCT Resource Monitoring and Control
rsct.core.sec 2.5.3.0 RSCT Security
rsct.core.sensorrm 2.5.3.0 RSCT Sensor Resource Manager
rsct.core.sr 2.5.3.0 RSCT Registry rsct.core.utils 2.5.3.0 RSCT Utilities
8/17/2019 CLUSTER - AIX - Installation de HACMP_eng
http://slidepdf.com/reader/full/cluster-aix-installation-de-hacmpeng 9/93
8/17/2019 CLUSTER - AIX - Installation de HACMP_eng
http://slidepdf.com/reader/full/cluster-aix-installation-de-hacmpeng 10/93
PowerHA 5.4 installation record
Technical dossier of PowerHA 5.4 installation
CLUSTER - AIX - Installation de HACMP_eng Technical paper 101093
NB: filesets minimum, versions to be upgraded according to AIX6.1 TL4 SP3 and PowerHA
5.4.1 SP8
Product Version Description
cluster.doc.en_US.es.ht ml 5.4.1.0 HAES Web-based HTML
cluster.doc.en_US.es.pd F 5.4.1.0 HAES pdf Documentation - U.S.
cluster.es.cl ient. lib 5.4.1.4 ES User Libraries
cluster.es.cl ient. rte 5.4.1.5 ES User Runtime
cluster.es.cl ient.utils 5.4.1.5 ES User Utilities
cluster.es.cl ient. wsm 5.4.1.5 Web based Smit
cluster.es.cs poc.cmds 5.4.1.5 ES CSPOC Commands
cluster.es.cs poc. dsh 5.4.1.0 ES CSPOC dsh cluster.es.cs poc. rte 5.4.1.3 ES CSPOC Runtime Commands
cluster.es.pl ugins.dhcp 5.4.1.0 ES Plugins - dhcp
cluster.es.pl ugins. dns 5.4.1.0 ES Plugins - Name Server
cluster.es.pl ugins.printserver
cluster.es.se rver.cfgast 5.4.1.0 ES Two-node Configuration
cluster.es.se rver.diag 5.4.1.5 ES Server Diags
cluster.es.se rver.events 5.4.1.5 ES Server Vents
cluster.es.se rver. rte 5.4.1.5 ES Base Server Runtime
cluster.es.se rver.testtool 5.4.1.1 ES Cluster Tool Test
cluster.es.se rver.utils 5.4.1.5 ES Server Utilities cluster.es.wo rksheets 5.4.1.3 Online Worksheets Planning
cluster.license 5.4.1.1 HACMP Electronic License
csm.client 1.7.1.0 Cluster Systems Management
csm.core 1.7.1.0 Cluster Systems Management
csm.deploy 1.7.1.0 Cluster Systems Management
csm.diagnostics 1.7.1.0 Cluster Systems Management
csm. dsh 1.7.1.0 Cluster Systems Dsh Management
cluster.es.cl ient. lib 5.4.1.4 ES User Libraries
cluster.es.cl ient. rte 5.4.1.5 ES User Runtime
cluster.es.cs poc. rte 5.4.0.0 ES CSPOC Runtime Commands
cluster.es.se rver.diag 5.4.0.0 ES Server Diags
cluster.es.se rver.events 5.4.0.0 ES Server Vents
cluster.es.se rver. rte 5.4.1.5 ES Base Server Runtime
cluster.es.se rver.utils 5.4.1.5 ES Server Utilities
csm.client 1.7.1.0 Cluster Systems Management
csm.core 1.7.1.0 Cluster Systems Management
csm.deploy 1.7.1.0 Cluster Systems Management
csm.diagnostics 1.7.1.0 Cluster Systems Management
csm. dsh 1.7.1.0 Cluster Systems Dsh Management cluster.man.en_US.es.da your 5.4.1.3 ES Man Pages - U.S. English
8/17/2019 CLUSTER - AIX - Installation de HACMP_eng
http://slidepdf.com/reader/full/cluster-aix-installation-de-hacmpeng 11/93
8/17/2019 CLUSTER - AIX - Installation de HACMP_eng
http://slidepdf.com/reader/full/cluster-aix-installation-de-hacmpeng 12/93
PowerHA 5.4 installation record
Technical dossier of PowerHA 5.4 installation
CLUSTER - AIX - Installation de HACMP_eng Technical paper 121293
To configure the two nodes with their address of bootup and to connect themselves in consol
If need be, to add manually the address persistente with the control chdev - L en0 - has alias4=' @IP', ' netmask'
and to withdraw it with the control chdev - L en0 - has delalias4=' @IP', ' netmask'
6.2 File netmon.cf
NB: Parameter setting called into question series incident cluster STOCK of the 2/18/2010. to
leave the empty file.
The /usr/es/sbin/cluster/netmon.cf file must be referred to make it possible to check the network
status.
! REQD 192.168.40.200
6.3 Checking of the parameters systems
- Checking of the parameter “fc_error_recov = fast_fail” on the cards Chanel fibre.
o Checking:for I in 0 1 2 3 4 5; C lsattr - El fscsi$i; give
o Modification if need be
for I in 0 1 2 3 4 5; C chdev - L fscsi$i - has fc_err_recov=fast_fail - P; give
- Values “No” were modified in the /etc/rc.net file. The following values were positioned:
/usr/sbin/no - Po ipforwarding=0 (option)/usr/sbin/no - Po subnetsarelocal=0
/usr/sbin/no - Po ipsendredirects=0/usr/sbin/no - Po routerevalidate=1
They can be installations via smit ---> Performance & Scheduling Resource - > Tuning Kernel& Network Parameters - >Tuning Network Parameters Options
Tuning Network Parameters Option
Move cursor to desired item and close Enter. . list Al Characteristics of Current Parameters Change/Show Current Parameters
Change/Show Parameters for Next Boot Save Current Parameters for Next Bootup Current Parameters reset to Defect Been worth
8/17/2019 CLUSTER - AIX - Installation de HACMP_eng
http://slidepdf.com/reader/full/cluster-aix-installation-de-hacmpeng 13/93
PowerHA 5.4 installation record
Technical dossier of PowerHA 5.4 installation
CLUSTER - AIX - Installation de HACMP_eng Technical paper 131393
Reset Next Parameters Bootup to Defect Been worth
To change the current options and to back up them for the next bootup.
- The /sbin/rc.boot file was modified to pass the value “syncd” from 60 to 10:“Starting the sync daemon”
/usr/sbin/syncd nohup 10 >/dev/null 2>&1These values can also be modified by POWERHA with the menu:
# smit hacmp-> Extended Configuration->Extended Performance Tuning Parameters
Configuration - >
Change/Show syncd frequency
To change the values systems of I/O Pacing “High toilets mark for pending Write I/Os per spins”(upper limit by file for the queued ES writings) and “Low toilets mark for pending Write I/Os perslips by” (lower limit by file for the queued ES writings).
These values must be 33 for the high and 24 for the low. To position with
# smit - > Environments System - >Change/Show Characteristics of OS
These values can also be changed with:
# smit hacmp-> Extended Configuration->Extended Performance Tuning Parameters
Configuration - > Exchange/Show I/O Pacing
The language chosen for the cluster is the en_US language.
The id' S of the users and the groups, the passwords of the users, must be identical on all the nodesof the cluster. The /etc/passwd files and those of the /etc/security repertoire must be identical on the
2 nodes.
8/17/2019 CLUSTER - AIX - Installation de HACMP_eng
http://slidepdf.com/reader/full/cluster-aix-installation-de-hacmpeng 14/93
PowerHA 5.4 installation record
Technical dossier of PowerHA 5.4 installation
CLUSTER - AIX - Installation de HACMP_eng Technical paper 141493
6.4 Organization principles of VG, VL and FS for POWERHA
The groups of volumes, logical volumes and filesystems must be known with the same definitionson each node. One will create volume groups on the first node:
The following general rules must be respected:
- to impose a major number on the group of volume (to determine the first availableone with lvlstmajor)
- if the mirroring is implemented by the LVM, to position the quorum with “No”,
- volume is positioned with auto--varyon with “No” for a VG Competitor, - to name logical volumes with their creation,
- to create the filesystems with logical volumes created previously and not to put themin automatic assembly at the initialization of the system,
- to rename the jfs2log of the filesystems,
Procedure:
Creation of the VG:mkvg - C - V [major number] - S 256 there [VG name] hdiskX
Creation of a jfs2log before the creation of the first jfs2Order logform to specify that this logical volume is a jfs2log
# /dev/log_XXX logformTo modify the jfs2log of each file system of the VG with the new name ofthe jfs2log
# chfs - has log=/dev/(lvlogname)/(fsname)
NB: the LV for the FS cluster will be created thereafter with C-SPOC
After having setting the VG “varyoff” on the first node, importation of the VG on the second node:
# importvg - V (major node) there (vgname) hdisk (X)
VG major volumes hdisk Label IP Mask
8/17/2019 CLUSTER - AIX - Installation de HACMP_eng
http://slidepdf.com/reader/full/cluster-aix-installation-de-hacmpeng 15/93
PowerHA 5.4 installation record
Technical dossier of PowerHA 5.4 installation
CLUSTER - AIX - Installation de HACMP_eng Technical paper 151593
6.5 POWERHA directory creation
The following repertoires were created:
- /usr/HACMP_TOOLS/scripts- To add inside the skeletons of the Script start_appli and stop_appli
In the repertoire Script, the Script of start and stop of the applications will be installed
With the bootup of the nodes, the application interfaces are configure according to the following
table:
Node Interface Type IP address Label IP Mask
gtyxsappm6p1 en0 bootup 7.27.224.62 gtyxsappm6p1_boot 255.255.255.0
gtyxsappm6p1 en0 persistent 192.168.40.191 gtyxsappm6p1 255.255.255.0
gtyxsappm6p2 en0 bootup 7.27.224.63 gtyxsappm6p2_boot 255.255.255.0
gtyxsappm6p2 en0 persistent 192.168.40.192 gtyxsappm6p2 255.255.255.0
6.6 Topology
6.6.1 Cluster-name Defi ni tion
Here cluster-name is defined, alongwith nodes belonging to the cluster, especially bootup networksand adapters. Caution: service adapters are defined in resources only.
Admin addresses do not form part of the POWERHA cluster, in fact addresses can access a node
irrespective of the status of the cluster
The cluster is defined in the menu smitty hacmp-> extended configuration->extended topologyconfiguration->configure year HACMP cluster - >add/change/show year HACMP cluster
New cluster
Name cluster = PM6_CL SMART_DB_REC_CL
6.6.2 Addi ti on of the nodes
Then nodes are added with smitty hacmp - > extended configuration->extended topology->configure HACMP nodes
8/17/2019 CLUSTER - AIX - Installation de HACMP_eng
http://slidepdf.com/reader/full/cluster-aix-installation-de-hacmpeng 16/93
8/17/2019 CLUSTER - AIX - Installation de HACMP_eng
http://slidepdf.com/reader/full/cluster-aix-installation-de-hacmpeng 17/93
PowerHA 5.4 installation record
Technical dossier of PowerHA 5.4 installation
CLUSTER - AIX - Installation de HACMP_eng Technical paper 171793
6.6.4 Creati on of si tes
Creation of sites is done via smitty hacmp-> extended configuration->extended topology
configuration->configure HACMP Sites → Add has Site
Characteristics of sites:
Name nodelist Predominance Protect_type
Data2 Gtyxorasmas01 Yes SGN
Data3 Gtyxorasmas02 No SGN
6.6.5 IP network Creation
The network being operational we chose the discovered IP-based Networks node types
Then POWERHA networks are created with smitty hacmp-> extended configuration->extended
topology configuration->configure HACMP Networks - >Add has Network to ClusterHACMP, to choose standard ether in discovered:
8/17/2019 CLUSTER - AIX - Installation de HACMP_eng
http://slidepdf.com/reader/full/cluster-aix-installation-de-hacmpeng 18/93
PowerHA 5.4 installation record
Technical dossier of PowerHA 5.4 installation
CLUSTER - AIX - Installation de HACMP_eng Technical paper 181893
Then,
Note: The parameter network Name is “net_vlan16 ”
Check if netmask is okay. (the netmask must be identical for the application interfaces). We canalso modify the network name.
Network Name Network
Standard
Netmask Attribute Enable IP
Takeover via IP
Alias
Offset
net_vlan16 Ether 255.255.255.0 public Yes []
8/17/2019 CLUSTER - AIX - Installation de HACMP_eng
http://slidepdf.com/reader/full/cluster-aix-installation-de-hacmpeng 19/93
PowerHA 5.4 installation record
Technical dossier of PowerHA 5.4 installation
CLUSTER - AIX - Installation de HACMP_eng Technical paper 191993
6.6.6 Bootup i nterface appl i cations Creation
Enter the command smitty hacmp-> extended configuration->extended topology configuration->configure HACMP Communication Application interfaces/Devices - >Add CommunicationApplication interfaces/Devices - >Add Communication discovered Interfaces and Devices - >
Communication Application interfaces - > net_vlan16
To select the application interfaces of bootup by “F7”:
Network: net_vlan16
Node Interface Type IP address Label IP Mask Name of the
networkPOWERHA
gtyxsappm6p1 en0 bootup 7.27.224.62 gtyxsappm6p1_boot 255.255.255.0 net_vlan16
gtyxsappm6p2 en0 bootup 7.27.224.63 gtyxsappm6p2_boot 255.255.255.0 net_vlan16
8/17/2019 CLUSTER - AIX - Installation de HACMP_eng
http://slidepdf.com/reader/full/cluster-aix-installation-de-hacmpeng 20/93
PowerHA 5.4 installation record
Technical dossier of PowerHA 5.4 installation
CLUSTER - AIX - Installation de HACMP_eng Technical paper 202093
6.6.7 Creati on of persistent addresses
Enter the command smitty hacmp-> extended configuration->extended topology configuration-
>configure HACMP Persist in Node IP Label/Addresses - >Add has Persistent Node IP
Label/Address
Label IP IP address Mask Node Type
gtyxsappm6p1 192.168.40.191 255.255.255.0 gtyxsappm6p1 Persistent
gtyxsappm6p2 192.168.40.192 255.255.255.0 gtyxsappm6p2 Persistent
6.6.8 Non-IP networks creation
It is about a network of the “Heart-happy” type via disc.
To configure it, it is first of all necessary to create a volume AIX group of type competitor
enhanced.
The discs must be known on the two nodes with PVID consistent. To make known with
POWERHA the configuration of the discs, one will make a surgical procedure of “discover” of theresources:
# smitty hacmp - > Extend Configuration - > Discover HACMP-related Informationfrom Configured Nodes
Berry Nodes PVID Disc
Berry datacenter 1 gtyxsappm6p1 00c6e0d4c56889a70000000000000000 hdisk1
Berry datacenter 2 gtyxsappm6p1 00c6e0d4c5688caf0000000000000000 hdisk4
Berry datacenter 1 gtyxsappm6p2 00c6e0d4c56889a70000000000000000 hdisk1
8/17/2019 CLUSTER - AIX - Installation de HACMP_eng
http://slidepdf.com/reader/full/cluster-aix-installation-de-hacmpeng 21/93
PowerHA 5.4 installation record
Technical dossier of PowerHA 5.4 installation
CLUSTER - AIX - Installation de HACMP_eng Technical paper 212193
Berry datacenter 2 gtyxsappm6p2 00c6e0d4c5688caf0000000000000000 hdisk4
Then to create a network of type heartbeat via disc with the menu:
# smitty hacmp->Extended Configuration Topology >Extended Configuration > Configures
HACMP Networks> To Add has Network to Cluster HACMP, to choose the type (Pre-definedSerial Type) diskhb and to allot a name to the network (a name is given by default, it can be
modified directly):
“Network Name” is net_disk hb_D2 for berry on the D2 datacenter and net_diskhb_D3 for berry ofthe D3 datacenter.
In order to allow the detection correct of the loss of the network of the diskhb type
#smitty hacmp - >Extended Configuration Topology >Extended Configuration > Configureyear HACMP Network Modulates > Change has Network Module Pre-defined Using Been
worth
To choose the network diskhb, then to modify “Failure Detection Misses “in “Fast”.
6.6.9 Addi ti on of the devices di skhb
8/17/2019 CLUSTER - AIX - Installation de HACMP_eng
http://slidepdf.com/reader/full/cluster-aix-installation-de-hacmpeng 22/93
PowerHA 5.4 installation record
Technical dossier of PowerHA 5.4 installation
CLUSTER - AIX - Installation de HACMP_eng Technical paper 222293
To add the corresponding devices with menu smitty hacmp-> extended configuration->extended
topology configuration->configure HACMP Communication Application interfaces/Devices ->Add Communication Application interfaces/Devices - >Add Pre-Defined Communication
Interfaces and Devices - >Communication Devices
To select the networks previously created (net_diskhb_D2 and net_diskhb_D3) and to fill the fields
(device name is arbitrary, on the other hand the device path is the path corresponding to the physical volume allotted to volume AIX group of the competitor type)
Network Name NetworkStandard Device Path Name node Device name
net_diskhb_D2 diskhb /dev/hdisk1 gtyxsappm6p1 pm6p1_hb_D2
net_diskhb_D3 diskhb /dev/hdisk4 gtyxsappm6p1 pm6p1_hb_D3
net_diskhb_D2 diskhb /dev/hdisk1 gtyxsappm6p2 pm6p2_hb_D2
net_diskhb_D3 diskhb /dev/hdisk4 gtyxsappm6p2 pm6p2_hb_D3
6.6.10 Heart-happy test of the di scs
To test the network heartbeat, to launch the control below:
Under /usr/sbin/rsct/bin
# ./dhb_read - p /dev/hdisk1 - R on gtyxsappm6p1 (receive mode)waiting for message talkback
# ./dhb_read - p /dev/hdisk1 - T on gtyxsappm6p2 (mode transmitted)
The message Link operating normally appears on the two machinesTo repeat the surgical procedure with the /dev/hdisk4 disc.
6.7 Resources discs POWERHA
6.7.1 Creation of the “shared Groups Volume”
Shared groups volumes must be created on the node gtyxsappm6p then imported on the nodegtyxsappm6p2.The discs must be known on the two nodes and the PVID must be consistent.
8/17/2019 CLUSTER - AIX - Installation de HACMP_eng
http://slidepdf.com/reader/full/cluster-aix-installation-de-hacmpeng 23/93
PowerHA 5.4 installation record
Technical dossier of PowerHA 5.4 installation
CLUSTER - AIX - Installation de HACMP_eng Technical paper 232393
To make known with POWERHA the configuration of the discs, one will make a surgical procedure of “discover” of the resources:
# smitty hacmp - > Extend Configuration - > - > Discover HACMP-relatedInformation from Configured Nodes
6.7.2 Synchronisation
A synchronisation/checking with the values by default of the menu smit hacmp >ExtendedConfiguration >Extended Verification and Synchronization makes it possible to check the coherence
of the parameters seized in topology and to upgrade the parameters POWERHA in the ODM of theother nodes.
Attention, so that this surgical procedure can take place, it is necessary that a file/usr/es/sbin/cluster/etc/rhosts and /etc/hosts exist on all the nodes with information IP communes
with the nodes.
8/17/2019 CLUSTER - AIX - Installation de HACMP_eng
http://slidepdf.com/reader/full/cluster-aix-installation-de-hacmpeng 24/93
PowerHA 5.4 installation record
Technical dossier of PowerHA 5.4 installation
CLUSTER - AIX - Installation de HACMP_eng Technical paper 242493
6.7.3 Al lowance of the discs on the si tes
Smit hacmp System Management (C-SPOC) HACMP Physical Volume Management
Configures Disk/Site Rentals for Crossite LVM Mirroring To Add Disk/Site Definition forCrossite LVM Mirroring
Berry 75DKBM1 Berry 2 75DKBN1
Hdisk22 75DKBM100DA hdisk5 75DKBN10077
Hdisk23 75DKBM100DB hdisk6 75DKBN10078
Hdisk24 75DKBM100DC hdisk7 75DKBN10079
Hdisk25 75DKBM100DD hdisk8 75DKBN1007A
Hdisk26 75DKBM100DE hdisk9 75DKBN100A6
Hdisk27 75DKBM100DF hdisk10 75DKBN100A7
Hdisk28 75DKBM100E0 hdisk47 75DKBN100BB
Hdisk29 75DKBM100E1 hdisk48 75DKBN100BC
Hdisk30 75DKBM100E2 hdisk11 75DKBN100C7
Hdisk31 75DKBM100E3 hdisk12 75DKBN100C8
8/17/2019 CLUSTER - AIX - Installation de HACMP_eng
http://slidepdf.com/reader/full/cluster-aix-installation-de-hacmpeng 25/93
PowerHA 5.4 installation record
Technical dossier of PowerHA 5.4 installation
CLUSTER - AIX - Installation de HACMP_eng Technical paper 252593
Hdisk32 75DKBM101E4 hdisk43 75DKBN100F5
Hdisk33 75DKBM101E5 hdisk13 75DKBN10174
Hdisk34 75DKBM101E6 hdisk14 75DKBN10175
Hdisk35 75DKBM101E7 hdisk15 75DKBN10176
Hdisk36 75DKBM101E8 hdisk16 75DKBN10177
Hdisk37 75DKBM101E9 hdisk17 75DKBN10178
Hdisk38 75DKBM101EA hdisk18 75DKBN1017D
Hdisk39 75DKBM101EB hdisk19 75DKBN101A3
Hdisk40 75DKBM101EC hdisk20 75DKBN101A4
Hdisk41 75DKBM101ED hdisk21 75DKBN101A5
Hdisk42 75DKBM101EE hdisk44 75DKBN101F0 Hdisk45 75DKBM10219
Hdisk49 75DKBM1021C
Hdisk50 75DKBM1021D
Hdisk46 75DKBM1031F
Hdisk3 75DKBM1103F
Hdisk4 75DKBM11141
6.8 Components of the groups of resource
6.8.1 The address of servi ce
Booster: the addresses of service are activated with POWERHA and override the addresses of
bootup which are the addresses by default on the network card (addresses of bootup present exceptPOWERHA).One defines the addresses of service in the resources part via menu the smitty hacmp - >
Extended Configuration - >Extended Resource Configuration->HACMP Extended Resources
Configuration->Configure HACMP IP-based service Labels/Add adresses-> has IP-based
service label/Address
8/17/2019 CLUSTER - AIX - Installation de HACMP_eng
http://slidepdf.com/reader/full/cluster-aix-installation-de-hacmpeng 26/93
PowerHA 5.4 installation record
Technical dossier of PowerHA 5.4 installation
CLUSTER - AIX - Installation de HACMP_eng Technical paper 262693
These addresses being they even defined in /etc/hosts
To choose Configurable one Multiple Nodes so that the address can toggle from one node toanother, validate and choose the name of the network; to enter the label of the address
IP-LABEL Type Network Servers IP Mask gtyxsappm6p service net_vlan16 gtyxsappm6p1/gtyxsappm6p2 192.168.40.190 255.255.255.0
6.8.2 The servers appl i cation
8/17/2019 CLUSTER - AIX - Installation de HACMP_eng
http://slidepdf.com/reader/full/cluster-aix-installation-de-hacmpeng 27/93
PowerHA 5.4 installation record
Technical dossier of PowerHA 5.4 installation
CLUSTER - AIX - Installation de HACMP_eng Technical paper 272793
By server application one gathers startup scripts and of Shutdown of the applications having to
boot and quit themselves automatically with POWERHA. Enter the command smitty hacmp->Extended Configuration - >Extended Resource Configuration->HACMP Extended
Resources Configuration->Configure HACMP Servers Application - >Add year Server
Application
To re-enter server application name as well as the paths of startup script and discontinuation.
Server
application startup script Script of discontinuation AS_PM6 /usr/HACMP_TOOLS/scripts/start_appli /usr/HACMP_TOOLS/scripts/stop_appli
Startup scripts and Shutdown of the “Servers Applications” are under the /usr/HACMP_TOOLS/scripts/ repertoire.
Important: The Script of start and stop application in POWERHA 5.4 can be synchronized
automatically by POWERHA by new functionality “spins collection managment”
8/17/2019 CLUSTER - AIX - Installation de HACMP_eng
http://slidepdf.com/reader/full/cluster-aix-installation-de-hacmpeng 28/93
PowerHA 5.4 installation record
Technical dossier of PowerHA 5.4 installation
CLUSTER - AIX - Installation de HACMP_eng Technical paper 282893
.
6.8.3 Appl i cation groups of resources
A group of resources POWERHA gathers all the elements which the cluster will have to protect
and thus toggle in the event of incident on the machine: a group of resources in general understandsan address of service which will have mounted with POWERHA, one or more groups volumes
which will be in varyon when POWERHA is booted, the associated filesystems which will havegone up with POWERHA, and finally the servers applications defined previously.
66..88..33..11 MMooddiif f iiccaattiioonn oof f tthhee ggrroouupp oof f rreessoouurrccee
It is first of all necessary to define a group of resources POWERHA with the following menu:
smitty hacmp->Extended Configuration - >Extended Resource Configuration->HACMP
Extended Resource Group Configuration-> To Add has Resource Group
To choose the mode of toggle, to validate, and inform the name of the group of resources and thenames of the nodes which will be able to take it again, the first node indicated will be the principal
node.
Resource Group Name RG_PM6 Inter-site Management Policy is unaware of Participating Node Name (S) gtyxsappm6p1 gtyxsappm6p2 Startup Policy Online One Only Home Node Fallover Policy Fallover To Next Priority Node In The Lists Fallback Policy Never Fallback
8/17/2019 CLUSTER - AIX - Installation de HACMP_eng
http://slidepdf.com/reader/full/cluster-aix-installation-de-hacmpeng 29/93
PowerHA 5.4 installation record
Technical dossier of PowerHA 5.4 installation
CLUSTER - AIX - Installation de HACMP_eng Technical paper 292993
66..88..33..22 CChhaannggee oof f tthhee ggrroouupp oof f rreessoouurrccee
Then, to associate with this group of resources created all the resources which it will have to protectwith menu the Configuration smitty hacmp->Extended - >Extended Resource Configuration-
>HACMP Extended Resource Group Configuration-> Changes/Show Resources andAttributes for has Resource Group To include the address of service, the server application, groups volumes.
CAUTION: the filesystems created in all protected groups volumes will have automatically gone
up with POWERHA without it being necessary to include them in the group of resources.
Resource Group Name RG_PM6 Participating Node Name (S) gtyxsappm6p1 gtyxsappm6p2 Startup Policy Online One Only Home Node Fallover Policy Fallover To Next Priority Node In The Lists Fallback Policy Never Fallback Site Relationship is unaware of Node Priority IP-based service Label gtyxsappm6p Filesystems Al Filesystems Consistency Check fsck Filesystems Recovery Method sequential
Filesystems/Directories to Be exported (NFSv3) Filesystems/Directories to Be exported (NFSv4)
Filesystems to Be NFS mounted
Network For NFS Mount Stable Filesystem/Directory for NFSv4 Storage Groups VGCL_PM6log VGCL_PM6redo
VGCL_PM6dat1 VGCL_PM6dat2 VGCL_PM6dat3 volume Competitor Groups Volume Use forced varyon for groups volume, necessary yew true Disks
GMVG Replicated Resources
GMD Replicated Resources PPRC Replicated Resources
ERCMF Replicated Resources
SVC PPRC Replicated Resources
AIX Connections Services
AIX Fast Connect Services
Shared Types Resources Application Servers AS_PM6 Highly Available Communication Links
Primary Workload Manager Class
Secondary Workload Manager Class
Delayed Fallback Timer
Miscellaneous Dated Automatically Importation Groups false Volume
8/17/2019 CLUSTER - AIX - Installation de HACMP_eng
http://slidepdf.com/reader/full/cluster-aix-installation-de-hacmpeng 30/93
PowerHA 5.4 installation record
Technical dossier of PowerHA 5.4 installation
CLUSTER - AIX - Installation de HACMP_eng Technical paper 303093
Takeover inactivates SA Disk Fencing false Filesystems mounted before IP configured false WPAR Name
Run Time Parameters:
Name gtyxsappm6p1 node To debug Level high Standard for hacmp. out format
Name gtyxsappm6p2 node To debug Level high Standard for hacmp. out format
6.8.4 Synchronisati on of the resources
Once the resources are defined it is necessary to carry out a new synchronisation of the cluster withsmit hacmp >Extended Configuration >Extended Verification and Synchronization and withcorrect the Automatically options errors found during checking in Yes .
8/17/2019 CLUSTER - AIX - Installation de HACMP_eng
http://slidepdf.com/reader/full/cluster-aix-installation-de-hacmpeng 31/93
PowerHA 5.4 installation record
Technical dossier of PowerHA 5.4 installation
CLUSTER - AIX - Installation de HACMP_eng Technical paper 313193
Cor rect the Automatically parameter errors found during checking” can be put at yes in certain
circumstances, in particular to position the time stamp of the VGDA to a common value at the timeof the taking into account of a volume groups.
8/17/2019 CLUSTER - AIX - Installation de HACMP_eng
http://slidepdf.com/reader/full/cluster-aix-installation-de-hacmpeng 32/93
PowerHA 5.4 installation record
Technical dossier of PowerHA 5.4 installation
CLUSTER - AIX - Installation de HACMP_eng Technical paper 323293
6.8.5 Modi fi cation SNMP for clstat
To edit /etc/snmpdv3.conf: to add the lineVACM_VIEW defaultView 1.3.6.1 .4.1.2.3.1.2.1.5 - included -
To quit/restart snmpdstopsrc - S snmpd
startsrc - S snmpd
To wait 2 minutes
6.8.6 Modi fi cation si te logs for hacmp. out
smitty hacmp > System Management (C-SPOC) >HACMP Log Viewing and Management >Exchange/Show has Cluster Log Directory
To choose hacmp. out
Change/Show has Cluster Log Directory
Select type but been worth in entry fields.Close Enter AFTER making Al desired exchanges.
[Entry fields]Cluster Log Name hacmp. out
Cluster Log Generated by Description vent sc>defect Log Destination Directory /var/hacmp/log
* Log Destination Directory [/tmp]
Allow Logs one Remote Filesystems false +
6.8.7 Boot of POWERHA
Boot of PowerHA on gtyxsappm6p and gtyxsappm6p2
#smitty clstart
Start Cluster Services
Select type but been worth in entry fields.
Close Enter AFTER making Al desired exchanges.
[Entry fields]
8/17/2019 CLUSTER - AIX - Installation de HACMP_eng
http://slidepdf.com/reader/full/cluster-aix-installation-de-hacmpeng 33/93
PowerHA 5.4 installation record
Technical dossier of PowerHA 5.4 installation
CLUSTER - AIX - Installation de HACMP_eng Technical paper 333393
* Start now, one both system restart but now +
Start Cluster Services one thesis nodes [gtyxsappm6p] +* Manage Resource Groups Automatically +
BROADCAST message At startup? true +Startup Cluster Daemon Information? true +Is checking errors unaware of? false +
Correct Automatically found during Interactively errors +cluster start?
checking of running
# tail - F /tmp/hacmp.out
At the end of the surgical procedure
Checking which we passed well on the address of service
#ifconfig - has Checking which groups volumes are quite various one#lsvg - O
Checking that all the files systems went up
#df - K Checking of the resources
# /usr/es/sbin/cluster/utilities/clfindres
The cluster being booted, the menus C-SPOC can be used to define logical volumes and thefilesystems.
8/17/2019 CLUSTER - AIX - Installation de HACMP_eng
http://slidepdf.com/reader/full/cluster-aix-installation-de-hacmpeng 34/93
PowerHA 5.4 installation record
Technical dossier of PowerHA 5.4 installation
CLUSTER - AIX - Installation de HACMP_eng Technical paper 343493
7 Definition of Logical Volumes and the Filesystems
The creation of the LV and FS will be made with menus CSPOC of POWERHA, the cluster being booted.
Procedure of implementation of logical Volumes and Filesystems:
o Creation of the Logical Volume of log (jfs2log)o Formatting of the jfs2log by the control “logform /dev/ <log name>” o Creation of Logical Volumeso Creation of the filing systemo Enlarging of the Filing system
7.1 Volume Logical creation of log
Logical volumes sharings can be created with the menus C-SPOC of POWERHA.
# smitty hacmp - > System Management (C-SPOC) - >HACMP Logical Management Volume- > Shared Logical Volume - >Add has Shared Logical Volume - > (Selection of the VG)
7.2 Creation of logical volumes
# smitty hacmp - > System Management (C-SPOC) - >HACMP Logical ManagementVolume - > Shared Logical Volume - >Add has Shared Logical Volume - > (Selection
of the VG then selection of the discs)
7.3 Creation of the filesystems
# smitty hacmp - > System Management (C-SPOC) - >HACMP Logical Management
Volume - > Shared Spins Systems - > Enhanced Journaled File Systems - >Add yearEnhanced Journaled File System one has Previously Defined Logical Volume - >(Selection of the LV)
Lists filesystems managed by PowerHA
/dev/pm6lvscan -- /invscan jfs2 -- rw No No /dev/pm6lvint -- /inter jfs2 -- rw No No
8/17/2019 CLUSTER - AIX - Installation de HACMP_eng
http://slidepdf.com/reader/full/cluster-aix-installation-de-hacmpeng 35/93
PowerHA 5.4 installation record
Technical dossier of PowerHA 5.4 installation
CLUSTER - AIX - Installation de HACMP_eng Technical paper 353593
/dev/pm6lvdveb -- /usr/sap/PM6/DVEBMGS00/work/tri jfs2 -- rw No
No /dev/pm6lvmirA -- /oracle/PM6/mirrlogA jfs2 -- cio, rw No No /dev/pm6lvmirB -- /oracle/PM6/mirrlogB jfs2 -- cio, rw No No /dev/pm6lvoriB -- /oracle/PM6/origlogB jfs2 -- cio, rw No No /dev/pm6lvoriA -- /oracle/PM6/origlogA jfs2 -- cio, rw No No /dev/pm6lvorastg -- /oracle/stage jfs2 -- rw No No /dev/pm6lvdata1 -- /oracle/PM6/sapdata1 jfs2 -- cio, rw No No /dev/pm6lvdata2 -- /oracle/PM6/sapdata2 jfs2 -- cio, rw No No /dev/pm6lvdata3 -- /oracle/PM6/sapdata3 jfs2 -- cio, rw No No /dev/pm6lvdata4 -- /oracle/PM6/sapdata4 jfs2 -- cio, rw No No /dev/pm6lvdata5 -- /oracle/PM6/sapdata5 jfs2 -- cio, rw No No /dev/pm6lvdata6 -- /oracle/PM6/sapdata6 jfs2 -- cio, rw No No /dev/PM6_lvora -- /oracle jfs2 -- cio, rw No No
/dev/lvorapm6 -- /oracle/PM6 jfs2 -- rw No No /dev/pm6lvsapreog -- /oracle/PM6/sapreorg jfs2 -- rw No No /dev/pm6lvmnt -- /sapmnt/PM6 jfs2 -- rw No No /dev/pm6lvmntpool -- /sapmnt/PM6/global/600SPOOL jfs2 -- rw No No /dev/pm6lvusrsap -- /usr/sap jfs2 -- rw No No /dev/pm6lvusap -- /usr/sap/PM6 jfs2 -- rw No No /dev/pm6lvstrans -- /usr/sap/trans jfs2 -- rw No No /dev/pm6lvadm -- /home/pm6adm jfs2 -- rw No No /dev/pm6lvarching -- /usr/sap/archiving jfs2 -- rw No No /dev/pm6lvcft -- /FS01/logiciel/cft jfs2 -- rw No No /dev/pm6lvdazl -- /FS01/logiciel/hpos jfs2 -- rw No No /dev/pm6lvorarch -- /oracle/PM6/oraarch jfs2 -- rw No No
7.4 Enlarging of the filesystem to the desired size
# smitty hacmp - > System Management (C-SPOC) - >HACMP Logical ManagementVolume - > Shared Spins Systems - > Enhanced Journaled File Systems -
>Change/Show Characteristics of has Shared Enhanced Journaled File System (Selection of the filesystem)
8 Notification of the errorsThe notification of errors makes it possible to detect any material element of the cluster likely tohave consequences on the behavior of the cluster.
Here it relates to the internal discs, the discs and the cards fibres. Any detection of problem willlead to a toggle or an error message in the log POWERHA.
Details are logués in hacmp. out and clstrmgr.debug, container:
- label of AIX error and its ID- name of the group of resources concerned
- name of the node on which the error took place
8/17/2019 CLUSTER - AIX - Installation de HACMP_eng
http://slidepdf.com/reader/full/cluster-aix-installation-de-hacmpeng 36/93
PowerHA 5.4 installation record
Technical dossier of PowerHA 5.4 installation
CLUSTER - AIX - Installation de HACMP_eng Technical paper 363693
A toggle is also started when there is a loss of group volume shared on one of the nodes (loss of
quorum, error LVM_SA_QUORCLOSE). POWERHA uses the notification of errors to supervisethe possible losses of quorum on groups volume. If the AIX daemon detects a loss of quorum
(Error Label LVM_SA_QUORCLOSE), the cluster manager is upgraded. It then starts a “move” ofthe resource containing group volume concerned towards the node of backup.
This last error (LVM_SA_QUORCLOSE) does not intervene systematically also we added adetection of error LVM_IO_FAIL. If this error is detected, one will check on this node which the
disc heartbeat is quite accessible. If the disc heartbeat is not accessible, one of deducted that all the paths Chanel fibre are cut, one starts a tilting by halt then - Q.
On the node of backup, the group of resources will be active again: the loss of quorum will be
bypassed by the group of resources and group volume could be in varyon. The daemon of eventmanagement will react only to the next loss of quorum.
ATTENTION it is necessary to modify the elements concerning each node on the node itself (the
synchronisation does not go for the notifications of errors.) Moreover, the notifications of error
are configured only when POWERHA is quitted on all the servers.
8/17/2019 CLUSTER - AIX - Installation de HACMP_eng
http://slidepdf.com/reader/full/cluster-aix-installation-de-hacmpeng 37/93
PowerHA 5.4 installation record
Technical dossier of PowerHA 5.4 installation
CLUSTER - AIX - Installation de HACMP_eng Technical paper 373793
8.1 Unattended setup of the notification of errors
The configuration is done with the menu:# smit hacmp - >Problem Tools Determination - >HACMP Error Notification - > Automatic
Error Notification Configures - >Add Error Notify Methods for Cluster Resources
To check the errors detected with:
# smit hacmp - >Problem Tools Determination - >HACMP Error Notification - > Automatic
Error Notification Configures - >List Error Notify Methods for Cluster Resources
8.2 Addition of a notification
8.2.1 Addition for LVM_IO_FAIL
We added a detection of error LVM_IO_FAIL. If this error is detected, one will check on this nodewhich the discs heartbeat are quite accessible. If the two discs heartbeat are not accessible, one of
deducted that all the paths Chanel fibre are cut, one starts a tilting by halt then - Q.
The halt - Q is launched by the Script: /usr/HACMP_tools/scripts/fcs_failover
8.2.2 Parameters
Notification Object Name lvm_io_failPersists across system restart? Yes
Process ID for uses by Notify Method [0] Select Error Class HARDWARE Select Standard Error LEAVE
Match Alertable errors? Nun Select Error Label [LVM_IO_FAIL]
Resource Name [LVDD] Resource Class [Al] Standard resource [Al]
Notify Method [/usr/HACMP_tools/scripts/fcs_failover $6 $9]
The Script fcs_failover checks the discs heartbeat by executable Hdalivepvid. The “return codes”this executable one to 99 indicates known the discs heartbeat are not accessible.
8.3 List supervised errors:
8/17/2019 CLUSTER - AIX - Installation de HACMP_eng
http://slidepdf.com/reader/full/cluster-aix-installation-de-hacmpeng 38/93
PowerHA 5.4 installation record
Technical dossier of PowerHA 5.4 installation
CLUSTER - AIX - Installation de HACMP_eng Technical paper 383893
the first column corresponds to the type of error generated by “errorlog” of AIX, the second
column is the name of the notification for the cluster manager.
With each notification there will be an action taken by POWERHA which will be forexample:/usr/es/sbin/cluster/diag/c l_logerror (Only one message in the logs)
gtyxsappm6p1: gtyxsappm6p1: HACMP Resource Notify Method Error gtyxsappm6p1: gtyxsappm6p1: /usr/es/sbin/cluster/diag/cl_failover hdisk0 gtyxsappm6p1: /usr/es/sbin/cluster/diag/cl_logerror hdisk3
gtyxsappm6p1: /usr/es/sbin/cluster/diag/cl_logerror hdisk2 gtyxsappm6p1: /usr/es/sbin/cluster/diag/cl_logerror hdisk14 gtyxsappm6p1: hdisk33 /usr/es/sbin/cluster/diag/cl_logerror gtyxsappm6p1: hdisk23 /usr/es/sbin/cluster/diag/cl_logerror gtyxsappm6p1: /usr/es/sbin/cluster/diag/cl_logerror hdisk13 gtyxsappm6p1: /usr/es/sbin/cluster/diag/cl_logerror hdisk5 gtyxsappm6p1: hdisk32 /usr/es/sbin/cluster/diag/cl_logerror gtyxsappm6p1: /usr/es/sbin/cluster/diag/cl_logerror hdisk6 gtyxsappm6p1: hdisk24 /usr/es/sbin/cluster/diag/cl_logerror gtyxsappm6p1: /usr/es/sbin/cluster/diag/cl_logerror hdisk8 gtyxsappm6p1: hdisk36 /usr/es/sbin/cluster/diag/cl_logerror gtyxsappm6p1: hdisk25 /usr/es/sbin/cluster/diag/cl_logerror gtyxsappm6p1: /usr/es/sbin/cluster/diag/cl_logerror hdisk16 gtyxsappm6p1: /usr/es/sbin/cluster/diag/cl_logerror hdisk17 gtyxsappm6p1: hdisk26 /usr/es/sbin/cluster/diag/cl_logerror gtyxsappm6p1: hdisk34 /usr/es/sbin/cluster/diag/cl_logerror gtyxsappm6p1: /usr/es/sbin/cluster/diag/cl_logerror hdisk7 gtyxsappm6p1: /usr/es/sbin/cluster/diag/cl_logerror hdisk15 gtyxsappm6p1: hdisk35 /usr/es/sbin/cluster/diag/cl_logerror gtyxsappm6p1: hdisk37 /usr/es/sbin/cluster/diag/cl_logerror gtyxsappm6p1: /usr/es/sbin/cluster/diag/cl_logerror hdisk9 gtyxsappm6p1: hdisk27 /usr/es/sbin/cluster/diag/cl_logerror gtyxsappm6p1: /usr/es/sbin/cluster/diag/cl_logerror hdisk19 gtyxsappm6p1: /usr/es/sbin/cluster/diag/cl_logerror hdisk18 gtyxsappm6p1: hdisk28 /usr/es/sbin/cluster/diag/cl_logerror gtyxsappm6p1: hdisk29 /usr/es/sbin/cluster/diag/cl_logerror gtyxsappm6p1: hdisk38 /usr/es/sbin/cluster/diag/cl_logerror gtyxsappm6p1: /usr/es/sbin/cluster/diag/cl_logerror hdisk11 gtyxsappm6p1: /usr/es/sbin/cluster/diag/cl_logerror hdisk10 gtyxsappm6p1: /usr/es/sbin/cluster/diag/cl_logerror hdisk21 gtyxsappm6p1: hdisk40 /usr/es/sbin/cluster/diag/cl_logerror gtyxsappm6p1: /usr/es/sbin/cluster/diag/cl_logerror hdisk20 gtyxsappm6p1: hdisk30 /usr/es/sbin/cluster/diag/cl_logerror gtyxsappm6p1: hdisk39 /usr/es/sbin/cluster/diag/cl_logerror gtyxsappm6p1: /usr/es/sbin/cluster/diag/cl_logerror hdisk12 gtyxsappm6p1: /usr/es/sbin/cluster/diag/cl_logerror fcs2 gtyxsappm6p1: /usr/es/sbin/cluster/diag/cl_logerror fcs0 gtyxsappm6p2: gtyxsappm6p2: HACMP Resource Notify Method Error gtyxsappm6p2: gtyxsappm6p2: /usr/es/sbin/cluster/diag/cl_failover hdisk0 gtyxsappm6p2: /usr/es/sbin/cluster/diag/cl_logerror hdisk3 gtyxsappm6p2: /usr/es/sbin/cluster/diag/cl_logerror hdisk2
8/17/2019 CLUSTER - AIX - Installation de HACMP_eng
http://slidepdf.com/reader/full/cluster-aix-installation-de-hacmpeng 39/93
PowerHA 5.4 installation record
Technical dossier of PowerHA 5.4 installation
CLUSTER - AIX - Installation de HACMP_eng Technical paper 393993
gtyxsappm6p2: /usr/es/sbin/cluster/diag/cl_logerror hdisk15 gtyxsappm6p2: hdisk32 /usr/es/sbin/cluster/diag/cl_logerror gtyxsappm6p2: hdisk23 /usr/es/sbin/cluster/diag/cl_logerror gtyxsappm6p2: /usr/es/sbin/cluster/diag/cl_logerror hdisk14 gtyxsappm6p2: /usr/es/sbin/cluster/diag/cl_logerror hdisk6 gtyxsappm6p2: hdisk31 /usr/es/sbin/cluster/diag/cl_logerror gtyxsappm6p2: /usr/es/sbin/cluster/diag/cl_logerror hdisk7 gtyxsappm6p2: hdisk24 /usr/es/sbin/cluster/diag/cl_logerror gtyxsappm6p2: /usr/es/sbin/cluster/diag/cl_logerror hdisk9 gtyxsappm6p2: hdisk35 /usr/es/sbin/cluster/diag/cl_logerror gtyxsappm6p2: hdisk25 /usr/es/sbin/cluster/diag/cl_logerror gtyxsappm6p2: /usr/es/sbin/cluster/diag/cl_logerror hdisk17 gtyxsappm6p2: /usr/es/sbin/cluster/diag/cl_logerror hdisk18 gtyxsappm6p2: hdisk26 /usr/es/sbin/cluster/diag/cl_logerror
gtyxsappm6p2: hdisk33 /usr/es/sbin/cluster/diag/cl_logerror gtyxsappm6p2: /usr/es/sbin/cluster/diag/cl_logerror hdisk8 gtyxsappm6p2: /usr/es/sbin/cluster/diag/cl_logerror hdisk16 gtyxsappm6p2: hdisk34 /usr/es/sbin/cluster/diag/cl_logerror gtyxsappm6p2: hdisk36 /usr/es/sbin/cluster/diag/cl_logerror gtyxsappm6p2: /usr/es/sbin/cluster/diag/cl_logerror hdisk10 gtyxsappm6p2: hdisk27 /usr/es/sbin/cluster/diag/cl_logerror gtyxsappm6p2: /usr/es/sbin/cluster/diag/cl_logerror hdisk20 gtyxsappm6p2: /usr/es/sbin/cluster/diag/cl_logerror hdisk19 gtyxsappm6p2: hdisk28 /usr/es/sbin/cluster/diag/cl_logerror gtyxsappm6p2: hdisk29 /usr/es/sbin/cluster/diag/cl_logerror gtyxsappm6p2: hdisk37 /usr/es/sbin/cluster/diag/cl_logerror gtyxsappm6p2: /usr/es/sbin/cluster/diag/cl_logerror hdisk12
gtyxsappm6p2: /usr/es/sbin/cluster/diag/cl_logerror hdisk11 gtyxsappm6p2: hdisk22 /usr/es/sbin/cluster/diag/cl_logerror gtyxsappm6p2: hdisk39 /usr/es/sbin/cluster/diag/cl_logerror gtyxsappm6p2: /usr/es/sbin/cluster/diag/cl_logerror hdisk21 gtyxsappm6p2: hdisk30 /usr/es/sbin/cluster/diag/cl_logerror gtyxsappm6p2: hdisk38 /usr/es/sbin/cluster/diag/cl_logerror gtyxsappm6p2: /usr/es/sbin/cluster/diag/cl_logerror hdisk13 gtyxsappm6p2: /usr/es/sbin/cluster/diag/cl_logerror fcs0
NOTE: List produced by the control “/usr/es/sbin/cluster/utilities/err_object_l ist”
8/17/2019 CLUSTER - AIX - Installation de HACMP_eng
http://slidepdf.com/reader/full/cluster-aix-installation-de-hacmpeng 40/93
PowerHA 5.4 installation record
Technical dossier of PowerHA 5.4 installation
CLUSTER - AIX - Installation de HACMP_eng Technical paper 404093
9 Tuning of the cluster
POWERHA fixes a 300 seconds deadlines at each event to finish.
Usual case:A node joining the cluster, launches the event “node_up” for one 300 seconds duration.
The node of help quits the applications and release the resources.The principal node takes again its resources and generates the event “node_up_complete”
which puts an end to the 300 second old timer.
However, in a case of graceful Shutdown with request for takeover, it may be that the time
cumulated for the surgical procedures of Shutdown of the applications, release andresumption of the resources, exceeds the 300 seconds.In such a case, when the lead time of 300s is past, POWERHA generates the event
“configuration too long” every 30 seconds, until the condition is raised. One can read this event in the /usr/HACMP_tools/logs/hacmp.out file (path by default) or in
the tree structure chosen by the user.This mechanism authorizes the call of a Script user intended to analyze the situation and to
take the adequate measures.
The modificat ion is done by the menu:
# smit hacmp-> Extended Configuration->Extended Vent Configuration->Change/Show
Time Until Warning
8/17/2019 CLUSTER - AIX - Installation de HACMP_eng
http://slidepdf.com/reader/full/cluster-aix-installation-de-hacmpeng 41/93
PowerHA 5.4 installation record
Technical dossier of PowerHA 5.4 installation
CLUSTER - AIX - Installation de HACMP_eng Technical paper 414193
The time allowed for the “fast” vents before the appearance of the event config_too_long ismodified by the field Event Duration entry. The time allowed for the “slow fox trot” vents
before a message of alarm is the sum of the fields Event Duration and Resource GroupDuration. The values by default of Vent Duration and Group Processing Time Resource areof 180 each one. One positions the values with 200 and 400.
10 POWERHA Spin Collection Management
Like volumes, certain files located on each servers of the cluster need to be identical for the good performance of the cluster, like the Script of start and Shutdown of the applications for example
With the new functionality “POWERHA Spins Collection” a list of files is automatically
maintained with identical by synchronisation.
By default, There exist two lists of files collection.
10.1 Administration
We can manage these lists via C_SPOC
# smitty hacmp - > System Management C-SPOC - >HACMP Spins CollectionManagement
8/17/2019 CLUSTER - AIX - Installation de HACMP_eng
http://slidepdf.com/reader/full/cluster-aix-installation-de-hacmpeng 42/93
PowerHA 5.4 installation record
Technical dossier of PowerHA 5.4 installation
CLUSTER - AIX - Installation de HACMP_eng Technical paper 424293
By default the synchronisation is done all the 10mn, if the “propagate files automatically” is putat “yes”
# smitty hacmp - > System Management C-SPOC - >HACMP Spins Collection
Management - > Manage File Collection - > Change/Show Automatic Update Time
8/17/2019 CLUSTER - AIX - Installation de HACMP_eng
http://slidepdf.com/reader/full/cluster-aix-installation-de-hacmpeng 43/93
PowerHA 5.4 installation record
Technical dossier of PowerHA 5.4 installation
CLUSTER - AIX - Installation de HACMP_eng Technical paper 434393
10.2 Creation of a new “File Collection”
To propagate the files useful for the administration of the cluster, there is the EEC a new“File called Collection”: hacmp_scripts_files
# smitty hacmp - > System Management C-SPOC - >HACMP Spins CollectionManagement - > Manage File Collection - >Add has File Collections
Spin Collection Name Spin Collection Description
Scripts_HACMP Script HACMP
8/17/2019 CLUSTER - AIX - Installation de HACMP_eng
http://slidepdf.com/reader/full/cluster-aix-installation-de-hacmpeng 44/93
PowerHA 5.4 installation record
Technical dossier of PowerHA 5.4 installation
CLUSTER - AIX - Installation de HACMP_eng Technical paper 444493
10.2.1 Addition of a file in this “File Collection”
# smitty hacmp - > System Management C-SPOC - >HACMP Spins Collections
Management - > Manage Fle in File Collections - Files >Add to has File Collections (To
choose the File Collections)
Addition of the files Script being under the /usr/HACMP_tools/scripts repertoire
8/17/2019 CLUSTER - AIX - Installation de HACMP_eng
http://slidepdf.com/reader/full/cluster-aix-installation-de-hacmpeng 45/93
PowerHA 5.4 installation record
Technical dossier of PowerHA 5.4 installation
CLUSTER - AIX - Installation de HACMP_eng Technical paper 454593
10.2.2 To propagate the fi l e created on the Fi les Collections:
For the propagation it is necessary to pass by
# smitty hacmp - > System Management C-SPOC - >HACMP Spins Collections Management- > Propagate Files in File Collections (To select the Files Collections)
8/17/2019 CLUSTER - AIX - Installation de HACMP_eng
http://slidepdf.com/reader/full/cluster-aix-installation-de-hacmpeng 46/93
PowerHA 5.4 installation record
Technical dossier of PowerHA 5.4 installation
CLUSTER - AIX - Installation de HACMP_eng Technical paper 464693
11 Annexure
11.1 ANNEXURE : Launching and Shutdown of the cluster
11.1.1 Launching of POWERHA
Syntax of the ordering of launching: smit clstart
11.1.2 Shutdown of POWERHA
Syntax of the ordering of launching: smit clstop
The Shutdown of POWERHA can be done in three ways:
- Bring Resource Groups Offline POWERHA is quitted properly. The applications arequitted, the resources are released. The node of help does not take again the resources.
- Move Resource Groups POWERHA is quitted properly. The applications are quitted, theresources are released, then the node of help takes again the resources and starts again the
applications of the node has just quitted itself.- Unmanage Resource Groups Seuls the procedures POWERHA are quitted. The
applications continue. The resources are not released.
8/17/2019 CLUSTER - AIX - Installation de HACMP_eng
http://slidepdf.com/reader/full/cluster-aix-installation-de-hacmpeng 47/93
PowerHA 5.4 installation record
Technical dossier of PowerHA 5.4 installation
CLUSTER - AIX - Installation de HACMP_eng Technical paper 474793
11.2 ANNEXURE : Logfiles of POWERHA
There exist a certain number of logfiles.
- /var/hacmp/adm/cluster. log supplied the traces relative to the principal events POWERHA and toerrors which have occurred on the cluster.
- /tmp/hacmp.out it is the file more used by the administrator. He reports in an exhaustive way the
events and most AIX controls executed by the Script.
11.3 ANNEXURE : Script
11.3.1 fcs_failover
gtyxsappm6p2_HACMP_: /usr/HACMP_TOOLS/scripts-- cat fcs_failover#! /bin/ksh# IBM_PROLOG_BEGIN_TAG# This is year automatically generated prolog.#### Licensed Materials - Property of IBM## Restricted Materials of IBM## (C) COPYRIGHT International Business Machines Corp. 1999.2003# Al Rights Reserved## US Government Users Restricted Rights - Uses, duplication gold# disclosure restricted by GSA ADP Schedule Contract with IBM Body.#
# IBM_PROLOG_END_TAG# @ (#) 08 1.8 src/43haes/usr/sbin/cluster/diag/cl_errnotify/cl_failover.sh,hacmp.diags, 51haes_r520, r5200422a 9/10/03 16:10: 12# $Id$
################################################################################# Name: fcs_failover## Description:## Syntax:## fcs_failover [device_name] [error_label]#
# device_name: name of HACMP device (gold rootvg|SP Switch to adapt)# which has received the error## error_label: the error to identify for the permanent hardware error
8/17/2019 CLUSTER - AIX - Installation de HACMP_eng
http://slidepdf.com/reader/full/cluster-aix-installation-de-hacmpeng 48/93
PowerHA 5.4 installation record
Technical dossier of PowerHA 5.4 installation
CLUSTER - AIX - Installation de HACMP_eng Technical paper 484893
#
# Called from:# errdemon## Cal to:# cl_log# clstop# clexit## Returns:################################################################################set - X
[“$VERBOSE_LOGGING” = “high”] && set - X
## Read the device name and the error label#DEVICE_NAME=$1ERROR_LABEL=$2
PATH= " $ (/usr/es/sbin/cluster/utilities/cl_get_path Al)” export PATH
PROGNAME=$ (basename $ {0})HA_DIR= " $ (cl_get_path)”
MSG= " HACMP errnotify vent ERROR: $ERROR_LABEL has occurred one device: $DEVICE_NAME. \N”
## Check yew to use changed the rental of the file from the defect# /tmp directory#HA_LOG_DIR=” /tmp”
dir_in_odm= ` odmget - Q " name=hacmp. out” HACMPlogs | grep been worth | awk “{print$3} “ | sed “S” //g” `
yew [[“X$dir_in_odm”! = “X/tmp”]] then
HA_LOG_DIR=$dir_in_odmfi
## Log the message to stdout ace well ace hacmp. out#cl_log 6000 “$MSG” $ERROR_LABEL $DEVICE_NAME cl_echo 6000 “$MSG” $ERROR_LABEL $DEVICE_NAME 2>> $HA_LOG_DIR/hacmp.out
## E-mail root#DATE= ` /usr/bin/date `/usr/es/sbin/cluster/utilities/cllsif | grep diskhb | awk “{print $NF”} | - Ru leaves|xargs |while read DISK1 DISK2CDISKHB1= ` echo $DISK1 | cut - f3 - D `
DISKHB2= ` echo $DISK2 | cut - f3 - D `give
8/17/2019 CLUSTER - AIX - Installation de HACMP_eng
http://slidepdf.com/reader/full/cluster-aix-installation-de-hacmpeng 49/93
PowerHA 5.4 installation record
Technical dossier of PowerHA 5.4 installation
CLUSTER - AIX - Installation de HACMP_eng Technical paper 494993
echo $DATE > /tmp/notify. $$echo $MSG >> /tmp/notify. $$e-mail root < /tmp/notify. $$/bin/rm - RF /tmp/notify. $$
# Yew you wish to add additional functionality to this Script# Please places it between the “####” lines
#### Start of using codefunction stopAppli_haltMachine{banner “TAKEOVER” “FORCED " >/dev/console print “###################################” >> $ {HA_LOG_DIR} /hacmp.out print “Shell Takeover Forced by: fcs_failover” >> $ {HA_LOG_DIR} /hacmp.out sleep 2#/usr/sbin/sync/usr/sbin/halt - Q}
################################################print “breakdown detectee by LVM_IO_FAIL “>> $ {HA_LOG_DIR} /hacmp.out print “Test Disc Heart bit of the network diskhb_01” >> $ {HA_LOG_DIR} /hacmp.out STAT_HB1=$ (/USR/HACMP_TOOLS/SCRIPTS/HDALIVEPVID R$ {DISKHB1} >> /dev/null; echo $?)STAT_HB2=$ (/USR/HACMP_TOOLS/SCRIPTS/HDALIVEPVID R$ {DISKHB2} >> /dev/null; echo $?)
yew [[$ {STAT_HB1} - 0]] && [[$ {STAT_HB2} - 0]]thenstopAppli_haltMachine
fi
#### End of using code
exit 0
8/17/2019 CLUSTER - AIX - Installation de HACMP_eng
http://slidepdf.com/reader/full/cluster-aix-installation-de-hacmpeng 50/93
PowerHA 5.4 installation record
Technical dossier of PowerHA 5.4 installation
CLUSTER - AIX - Installation de HACMP_eng Technical paper 505093
11.4 ANNEXURE : Snap
<VER
</VER
<DSC 20091125 -- </DSC
================================================================================ COMMAND: cllscf ================================================================================ Name cluster: PM6_CL Cluster Connection Authentication Mode: Standard Cluster Message Authentication Mode: Nun Cluster Message Encryption: Nun Use Persistent Labels for Communication: No There were 3 networks defined: net_diskhb_D2, net_diskhb_D3, net_vlan16 There are 2 nodes in this cluster
NODE gtyxsappm6p1:
This node has 3 IP-based service label (S):
IP-based service Label pm6p1_hb_D2:
IP address: /dev/hdisk1
Address hardware:
Network: net_diskhb_D2
Attribute: serial
Aliased Address?: Sayable
IP-based service Label pm6p1_hb_D2 has No communication application
interfaces.
IP-based service Label pm6p1_hb_D2 has No communication applicationinterfaces for recovery.
IP-based service Label pm6p1_hb_D3:
IP address: /dev/hdisk4
Address hardware:
Network: net_diskhb_D3
Attribute: serial
Aliased Address?: Sayable
IP-based service Label pm6p1_hb_D3 has No communication applicationinterfaces.
8/17/2019 CLUSTER - AIX - Installation de HACMP_eng
http://slidepdf.com/reader/full/cluster-aix-installation-de-hacmpeng 51/93
PowerHA 5.4 installation record
Technical dossier of PowerHA 5.4 installation
CLUSTER - AIX - Installation de HACMP_eng Technical paper 515193
IP-based service Label pm6p1_hb_D3 has No communication application
interfaces for recovery.
IP-based service Label gtyxsappm6p:
IP address: 192.168.40.190
Address hardware:
Network: net_vlan16
Attribute: public
Aliased Address?: Enable
IP-based service Label gtyxsappm6p has 1 communication applicationinterfaces. (Alternate Service) Communication Interfaces 1: gtyxsappm6p1_boot
IP address: 7.27.224.62
Network: net_vlan16
Attribute: public
Alias address for heartbeat:
IP-based service Label gtyxsappm6p has No communication application
interfaces for recovery.
NODE gtyxsappm6p2: This node has 3 IP-based service label (S):
IP-based service Label pm6p2_hb_D2:
IP address: /dev/hdisk1
Address hardware: Network: net_diskhb_D2
Attribute: serial
Aliased Address?: Sayable
IP-based service Label pm6p2_hb_D2 has No communication applicationinterfaces.
IP-based service Label pm6p2_hb_D2 has No communication application
interfaces for recovery.
IP-based service Label pm6p2_hb_D3:
IP address: /dev/hdisk4 Address hardware:
Network: net_diskhb_D3
Attribute: serial
Aliased Address?: Sayable
8/17/2019 CLUSTER - AIX - Installation de HACMP_eng
http://slidepdf.com/reader/full/cluster-aix-installation-de-hacmpeng 52/93
PowerHA 5.4 installation record
Technical dossier of PowerHA 5.4 installation
CLUSTER - AIX - Installation de HACMP_eng Technical paper 525293
IP-based service Label pm6p2_hb_D3 has No communication application
interfaces. IP-based service Label pm6p2_hb_D3 has No communication application
interfaces for recovery.
IP-based service Label gtyxsappm6p:
IP address: 192.168.40.190
Address hardware:
Network: net_vlan16
Attribute: public
Aliased Address?: Enable
IP-based service Label gtyxsappm6p has 1 communication application
interfaces. (Alternate Service) Communication Interfaces 1: gtyxsappm6p2_boot
IP address: 7.27.224.63
Network: net_vlan16
Attribute: public
Alias address for heartbeat:
IP-based service Label gtyxsappm6p has No communication application
interfaces for recovery.
Breakdown of network connections:
Connections to network net_diskhb_D2 Node gtyxsappm6p1 is connected to network net_diskhb_D2 by thesis application
interfaces:
pm6p1_hb_D2
Node gtyxsappm6p2 is connected to network net_diskhb_D2 by thesis application
interfaces: pm6p2_hb_D2
Connections to network net_diskhb_D3 Node gtyxsappm6p1 is connected to network net_diskhb_D3 by thesis application
interfaces: pm6p1_hb_D3
Node gtyxsappm6p2 is connected to network net_diskhb_D3 by thesis application
interfaces: pm6p2_hb_D3
Connections to network net_vlan16
8/17/2019 CLUSTER - AIX - Installation de HACMP_eng
http://slidepdf.com/reader/full/cluster-aix-installation-de-hacmpeng 53/93
PowerHA 5.4 installation record
Technical dossier of PowerHA 5.4 installation
CLUSTER - AIX - Installation de HACMP_eng Technical paper 535393
Node gtyxsappm6p1 is connected to network net_vlan16 by thesis application
interfaces: gtyxsappm6p1_boot
gtyxsappm6p
Node gtyxsappm6p2 is connected to network net_vlan16 by thesis application
interfaces: gtyxsappm6p2_boot
gtyxsappm6p
COMMAND cllscf returned 0
================================================================================ COMMAND: cllsnw ================================================================================ Network Attribute Alias Monitor method Node To adapt (S)
sayable net_diskhb_D2 serial Defect monitoring gtyxsappm6p1 pm6p1_hb_D2 gtyxsappm6p2 pm6p2_hb_D2
sayable net_diskhb_D3 serial Defect monitoring gtyxsappm6p1 pm6p1_hb_D3 gtyxsappm6p2 pm6p2_hb_D3
net_vlan16 public Enable Defect monitoring gtyxsappm6p1 gtyxsappm6p1_boot
gtyxsappm6p gtyxsappm6p2 gtyxsappm6p2_boot gtyxsappm6p
COMMAND cllsnw returned 0
================================================================================ COMMAND: cllsif ================================================================================ Adapter Type Network Net Standard Attribute Node IP address Address HardwareInterfaces Name Global Name Netmask Alias for HB
pm6p1_hb_D2 service net_diskhb_D2 diskhb serial gtyxsappm6p1 /dev/hdisk1
hdisk1 pm6p1_hb_D3 service net_diskhb_D3 diskhb serial gtyxsappm6p1 /dev/hdisk4
hdisk4 gtyxsappm6p1_boot bootup net_vlan16 public ether gtyxsappm6p1 7.27.224.62 en0255.255.255.0 gtyxsappm6p service net_vlan16 public ether gtyxsappm6p1 192.168.40.190
255.255.255.0 pm6p2_hb_D2 service net_diskhb_D2 diskhb serial gtyxsappm6p2 /dev/hdisk1
hdisk1 pm6p2_hb_D3 service net_diskhb_D3 diskhb serial gtyxsappm6p2 /dev/hdisk4
hdisk4 gtyxsappm6p2_boot bootup net_vlan16 public ether gtyxsappm6p2 7.27.224.63 en0
255.255.255.0 gtyxsappm6p service net_vlan16 public ether gtyxsappm6p2 192.168.40.190255.255.255.0
8/17/2019 CLUSTER - AIX - Installation de HACMP_eng
http://slidepdf.com/reader/full/cluster-aix-installation-de-hacmpeng 54/93
8/17/2019 CLUSTER - AIX - Installation de HACMP_eng
http://slidepdf.com/reader/full/cluster-aix-installation-de-hacmpeng 55/93
PowerHA 5.4 installation record
Technical dossier of PowerHA 5.4 installation
CLUSTER - AIX - Installation de HACMP_eng Technical paper 555593
Name gtyxsappm6p1 node To debug Level high Standard for hacmp. out format
Name gtyxsappm6p2 node To debug Level high Standard for hacmp. out format
COMMAND clshowres returned 0
clsnapshot: Following information is retrieved from node: gtyxsappm6p1 -------------------------------------------------
================================================================================ COMMAND: netstat - I ================================================================================ Name MTU Network Address ZoneID Ipkts Ierrs Opkts Oerrs coll en0 1500 link-2 3e.fd.13.4d.3.14 - 441361590 0 228585740 0 0 en0 1500 7.27.224 gtyxsappm6p1_boots - 441361590 0 228585740 0 0 en0 1500 192.168.40 gtyxsappm6p1. pharma. avs - 441361590 0 228585740 0 0 en0 1500 192.168.40 gtyxsappm6p. pharma. aves - 441361590 0 228585740 0 0 lo0 16896 link-1 - 1490005622 0 1488897666 0 0 lo0 16896 127 loopback - 1490005622 0 1488897666 0 0 lo0 16896:: 1 1 1490005622 0 1488897666 0 0
================================================================================ COMMAND: netstat - in ================================================================================ Name MTU Network Address ZoneID Ipkts Ierrs Opkts Oerrs coll en0 1500 link-2 3e.fd.13.4d.3.14 - 441361590 0 228585745 0 0 en0 1500 7.27.224 7.27.224.62 - 441361590 0 228585745 0 0 en0 1500 192.168.40 192.168.40.191 - 441361590 0 228585745 0 0 en0 1500 192.168.40 192.168.40.190 - 441361590 0 228585745 0 0 lo0 16896 link-1 - 1490005624 0 1488897668 0 0 lo0 16896 127 127.0.0.1 - 1490005624 0 1488897668 0 0 lo0 16896:: 1 1 1490005624 0 1488897668 0 0
================================================================================ COMMAND: No - has ================================================================================
arpqsize = 12
arpt_killc = 20
arptab_bsiz = 7 arptab_nb = 149
bcastping = 0
clean_partial_conns = 0
delayack = 0
delayackports = {}
dgd_packets_lost = 3
dgd_ping_time = 5
dgd_retry_time = 5
8/17/2019 CLUSTER - AIX - Installation de HACMP_eng
http://slidepdf.com/reader/full/cluster-aix-installation-de-hacmpeng 56/93
PowerHA 5.4 installation record
Technical dossier of PowerHA 5.4 installation
CLUSTER - AIX - Installation de HACMP_eng Technical paper 565693
directed_broadcast = 0
fasttimo = 200
icmp6_errmsg_rate = 10
icmpaddressmask = 0 ie5_old_multicast_mapping = 0
ifsize = 256
ip6_defttl = 64
ip6_prune = 1
ip6forwarding = 0
ip6srcrouteforward = 1
ip_ifdelete_notify = 0
ip_nfrag = 200 ipforwarding=0
ipfragttl = 2
ipignoreredirects = 0
ipqmaxlen = 100
ipsendredirects=0 ipsrcrouteforward=1
ipsrcrouterecv = 1
ipsrcroutesend=1
llsleep_timeout = 3
lo_perf = 1
lowthresh = 90 main_if6 = 0
main_site6 = 0
maxnip6q = 20
maxttl = 255
medthresh = 95
mpr_policy = 1
multi_homed = 1
nbc_limit = 15073280
nbc_max_cache = 131072
nbc_min_cache = 1 nbc_ofile_hashsz = 12841
nbc_pseg = 0 nbc_pseg_limit = 30146560
ndd_event_name = {Al}
ndd_event_tracing = 0
ndp_mmaxtries = 3
ndp_umaxtries = 3
ndpqsize = 50
ndpt_down = 3
ndpt_keep = 120
ndpt_probe = 5
ndpt_reachable = 30
8/17/2019 CLUSTER - AIX - Installation de HACMP_eng
http://slidepdf.com/reader/full/cluster-aix-installation-de-hacmpeng 57/93
PowerHA 5.4 installation record
Technical dossier of PowerHA 5.4 installation
CLUSTER - AIX - Installation de HACMP_eng Technical paper 575793
ndpt_retrans = 1
net_buf_size = {Al}
net_buf_type = {Al}
net_malloc_frag_mask = {0}
netm_page_promote = 1
nonlocsrcroute=1
nstrpush = 8
passive_dgd = 0
pmtu_default_age = 10
pmtu_expire = 10
pmtu_rediscover_interval = 30
psebufcalls = 20 psecache = 1
psetimers = 20
rfc1122addrchk = 0 rfc1323 = 0
rfc2414 = 1
route _expire = 1
routerevalidate=1
rto_high = 64
rto_length = 13
rto_limit = 7
rto_low = 1
sack = 0
sb_max = 1048576
send_file_duration = 300
site6_index = 0
sockthresh = 85
sodebug = 0
sodebug_env = 0
somaxconn = 1024
strctlsz = 1024
strmsgsz = 0 strthresh = 85
strturncnt = 15
subnetsarelocal=0
tcp_bad_port_limit = 0
tcp_ecn = 0
tcp_ephemeral_high = 65535
tcp_ephemeral_low = 32768
tcp_finwait2 = 1200
tcp_icmpsecure = 0
tcp_init_window = 0 tcp_inpcb_hashtab_siz = 24499
tcp_keepcnt = 8
8/17/2019 CLUSTER - AIX - Installation de HACMP_eng
http://slidepdf.com/reader/full/cluster-aix-installation-de-hacmpeng 58/93
PowerHA 5.4 installation record
Technical dossier of PowerHA 5.4 installation
CLUSTER - AIX - Installation de HACMP_eng Technical paper 585893
tcp_keepidle = 14400
tcp_keepinit = 150
tcp_keepintvl = 150
tcp_limited_transmit = 1
tcp_low_rto = 0
tcp_maxburst = 0
tcp_mssdflt = 1460
tcp_nagle_limit = 65535
tcp_nagleoverride = 0
tcp_ndebug = 100
tcp_newreno = 1
tcp_nodelayack = 0 tcp_pmtu_discover = 1
tcp_recvspace = 16384
tcp_sendspace = 16384 tcp_tcpsecure = 0
tcp_timewait = 1
tcp_ttl = 60
tcprexmtthresh = 3
tcptr_enable = 0
thewall = 60293120
timer_wheel_tick = 0
tn_filter = 1
udp_bad_port_limit = 0
udp_ephemeral_high = 65535
udp_ephemeral_low = 32768
udp_inpcb_hashtab_siz = 24499
udp_pmtu_discover = 1
udp_recvspace = 42080
udp_sendspace = 9216
udp_ttl = 30
udpcksum = 1
use_sndbufpool = 1
================================================================================ COMMAND: clchsyncd ================================================================================ syncd frequency: 10 High toilets mark: 33 Low toilets mark: 24
================================================================================ COMMAND: lsdev - DC yew ================================================================================
en0 Available Standard Network Ethernet Interfaces et0 Defined IEEE 802.3 Network Ethernet Interfaces lo0 Available Loopback Network Interfaces
8/17/2019 CLUSTER - AIX - Installation de HACMP_eng
http://slidepdf.com/reader/full/cluster-aix-installation-de-hacmpeng 59/93
PowerHA 5.4 installation record
Technical dossier of PowerHA 5.4 installation
CLUSTER - AIX - Installation de HACMP_eng Technical paper 595993
================================================================================ COMMAND: lsdev - DC disk ================================================================================ hdisk0 Available Virtual SCSI Disk Drive hdisk1 Available 18-T1-01 IBM MPIO FC 2107 hdisk2 Available 18-T1-01 IBM MPIO FC 2107 hdisk3 Available 14-T1-01 IBM MPIO FC 2107 hdisk4 Available 14-T1-01 IBM MPIO FC 2107 hdisk5 Available 14-T1-01 IBM MPIO FC 2107 hdisk6 Available 14-T1-01 IBM MPIO FC 2107 hdisk7 Available 14-T1-01 IBM MPIO FC 2107 hdisk8 Available 14-T1-01 IBM MPIO FC 2107 hdisk9 Available 14-T1-01 IBM MPIO FC 2107 hdisk10 Available 14-T1-01 IBM MPIO FC 2107
hdisk11 Available 14-T1-01 IBM MPIO FC 2107 hdisk12 Available 14-T1-01 IBM MPIO FC 2107 hdisk13 Available 14-T1-01 IBM MPIO FC 2107 hdisk14 Available 14-T1-01 IBM MPIO FC 2107 hdisk15 Available 14-T1-01 IBM MPIO FC 2107 hdisk16 Available 14-T1-01 IBM MPIO FC 2107 hdisk17 Available 18-T1-01 IBM MPIO FC 2107 hdisk18 Available 18-T1-01 IBM MPIO FC 2107 hdisk19 Available 18-T1-01 IBM MPIO FC 2107 hdisk20 Available 18-T1-01 IBM MPIO FC 2107 hdisk21 Available 18-T1-01 IBM MPIO FC 2107 hdisk22 Available 18-T1-01 IBM MPIO FC 2107 hdisk23 Available 18-T1-01 IBM MPIO FC 2107
hdisk24 Available 18-T1-01 IBM MPIO FC 2107 hdisk25 Available 18-T1-01 IBM MPIO FC 2107 hdisk26 Available 12-T1-01 IBM MPIO FC 2107 hdisk27 Available 12-T1-01 IBM MPIO FC 2107 hdisk28 Available 12-T1-01 IBM MPIO FC 2107 hdisk29 Available 12-T1-01 IBM MPIO FC 2107 hdisk30 Available 12-T1-01 IBM MPIO FC 2107 hdisk31 Available 12-T1-01 IBM MPIO FC 2107 hdisk32 Available 12-T1-01 IBM MPIO FC 2107 hdisk33 Available 12-T1-01 IBM MPIO FC 2107 hdisk34 Available 12-T1-01 IBM MPIO FC 2107 hdisk35 Available 12-T1-01 IBM MPIO FC 2107 hdisk36 Available 12-T1-01 IBM MPIO FC 2107
hdisk37 Available 12-T1-01 IBM MPIO FC 2107 hdisk38 Available 12-T1-01 IBM MPIO FC 2107 hdisk39 Available 12-T1-01 IBM MPIO FC 2107 hdisk40 Available 12-T1-01 IBM MPIO FC 2107 hdisk41 Available 12-T1-01 IBM MPIO FC 2107 hdisk42 Available 12-T1-01 IBM MPIO FC 2107 hdisk43 Available 12-T1-01 IBM MPIO FC 2107 hdisk44 Available 12-T1-01 IBM MPIO FC 2107 hdisk45 Available 12-T1-01 IBM MPIO FC 2107 hdisk46 Available 12-T1-01 IBM MPIO FC 2107 hdisk47 Available 12-T1-01 IBM MPIO FC 2107 hdisk48 Available 12-T1-01 IBM MPIO FC 2107 hdisk49 Available 12-T1-01 IBM MPIO FC 2107
hdisk50 Available 12-T1-01 IBM MPIO FC 2107
================================================================================
8/17/2019 CLUSTER - AIX - Installation de HACMP_eng
http://slidepdf.com/reader/full/cluster-aix-installation-de-hacmpeng 60/93
PowerHA 5.4 installation record
Technical dossier of PowerHA 5.4 installation
CLUSTER - AIX - Installation de HACMP_eng Technical paper 606093
COMMAND: lsvg ================================================================================ rootvg VGCL_PM6redo VGCL_PM6log VGCL_HB_D3 VGCL_HB_D2 FS01vg VGCL_PM6dat1 VGCL_PM6dat2 VGCL_PM6dat3 VG_TEMPO
================================================================================ COMMAND: lspv ================================================================================ hdisk0 00c6e0d4c0586bb9 rootvg active hdisk1 00c6e0d4c56889a7 VGCL_HB_D2 hdisk2 00c6e0d4c5688a8d VGCL_PM6log competitor hdisk3 00c6e0d4c5688bae VGCL_PM6log competitor
hdisk4 00c6e0d4c5688caf VGCL_HB_D3 hdisk5 00c6e0d4ee533cc6 VGCL_PM6log competitor hdisk6 00c6e0d4ee533d38 VGCL_PM6redo competitor hdisk7 00c6e0d4ee533daa VGCL_PM6dat1 competitor hdisk8 00c6e0d4ee533e1a VGCL_PM6dat1 competitor hdisk9 00c6e0d4ee533e96 VGCL_PM6dat2 competitor
hdisk10 00c6e0d4ee533f0b VGCL_PM6dat2 competitor hdisk11 00c6e0d4ee533f8a VGCL_PM6dat2 competitor hdisk12 00c6e0d4ee533ffe VGCL_PM6dat3 competitor hdisk13 00c6e0d4ee5340a8 VGCL_PM6log competitor hdisk14 00c6e0d4ee53411b VGCL_PM6log competitor hdisk15 00c6e0d4ee53419a VGCL_PM6dat1 competitor hdisk16 00c6e0d4ee53420c VGCL_PM6dat1 competitor hdisk17 00c6e0d4ee534282 VGCL_PM6dat1 competitor hdisk18 00c6e0d4ee534306 VGCL_PM6dat2 competitor hdisk19 00c6e0d4ee534375 VGCL_PM6dat2 competitor hdisk20 00c6e0d4ee5343f2 VGCL_PM6dat3 competitor hdisk21 00c6e0d4ee534473 VGCL_PM6dat3 competitor hdisk22 00c6e0d4ee5344f1 FS01vg active
hdisk23 00c6e0d4ee534564 VGCL_PM6log competitor hdisk24 00c6e0d4ee5345ce VGCL_PM6redo competitor hdisk25 00c6e0d4ee534639 VGCL_PM6dat1 competitor hdisk26 00c6e0d4ee5346c0 VGCL_PM6dat1 competitor hdisk27 00c6e0d4ee534733 VGCL_PM6dat2 competitor hdisk28 00c6e0d4ee5347a9 VGCL_PM6dat2 competitor hdisk29 00c6e0d4ee53481e VGCL_PM6dat2 competitor hdisk30 00c6e0d4ee534894 VGCL_PM6dat3 competitor hdisk31 00c6e0d4ee534901 VG_TEMPO active hdisk32 00c6e0d4ee534980 VGCL_PM6log competitor hdisk33 00c6e0d4ee5349f1 VGCL_PM6log competitor hdisk34 00c6e0d4ee534a5d VGCL_PM6dat1 competitor hdisk35 00c6e0d4ee534ad5 VGCL_PM6dat1 competitor hdisk36 00c6e0d4ee534b45 VGCL_PM6dat1 competitor hdisk37 00c6e0d4ee 534bd 4 VGCL_PM6dat2 competitor hdisk38 00c6e0d4ee534c4e VGCL_PM6dat2 competitor hdisk39 00c6e0d4ee534cbb VGCL_PM6dat3 competitor
8/17/2019 CLUSTER - AIX - Installation de HACMP_eng
http://slidepdf.com/reader/full/cluster-aix-installation-de-hacmpeng 61/93
PowerHA 5.4 installation record
Technical dossier of PowerHA 5.4 installation
CLUSTER - AIX - Installation de HACMP_eng Technical paper 616193
hdisk40 00c6e0d4ee534d2f VGCL_PM6dat3 competitor hdisk41 00c6e0d4ee534d99 VG_TEMPO active hdisk42 00c6e0d4ee534e12 VG_TEMPO active hdisk43 00c6e0c44df3c266 Nun hdisk44 00c6e0c44df3f640 VGCL_PM6log competitor hdisk45 00c6e0c44df41276 VGCL_PM6log competitor hdisk46 00c6e0c44df4299f Nun hdisk47 00c6e0d496e3dbee VGCL_PM6log competitor hdisk48 00c6e0d496e3fb07 VGCL_PM6log competitor hdisk49 00c6e0d496e41099 VGCL_PM6log competitor hdisk50 00c6e0d496e4291a VGCL_PM6log competitor
================================================================================
COMMAND: df ================================================================================ Filesystem 512-blocks Free %Used Iused %Iused Mounted one /dev/hd4 2883584 2269960 22% 13340 5%/ /dev/hd2 6029312 1445208 77% 46017 22% /usr /dev/hd9var 2359296 935152 61% 27558 21% /var /dev/hd3 4456448 3712304 17% 2702 1% /tmp /dev/hd11admin 262144 261416 1% 5 1% /admin /proc - - - - - /proc /dev/hd10opt 262144 66880 75% 2054 21% /opt /dev/lvusers 2097152 2095968 1% 31 1% /usersconnect /dev/lvfs01 13762560 12988568 6% 3750 1% /FS01 /dev/lvfs80 19005440 15006416 22% 212459 12% /FS80
/dev/lv_tempo 524288000 235012976 56% 8901 1% /TEMPO /dev/pm6lvcft 1966080 1309432 34% 8326 6% /FS01/logiciel/cft /dev/pm6lvdazl 4063232 2872968 30% 8829 3% /FS01/logiciel/hpos /dev/pm6lvadm 917504 906080 2% 37 1% /home/pm6adm /dev/pm6lvint 1835008 1834072 1% 4 1% /inter /dev/pm6lvscan 1835008 1834040 1% 4 1% /invscan /dev/PM6_lvora 5242880 4697808 11% 671 1% /oracle /dev/lvorapm6 12058624 3284304 73% 19710 5% /oracle/PM6 /dev/pm6lvmirA 1048576 523392 51% 5 1% /oracle/PM6/mirrlogA /dev/pm6lvmirB 1048576 523392 51% 5 1% /oracle/PM6/mirrlogB /dev/pm6lvorarch 123731968 102000032 18% 93 1% /oracle/PM6/oraarch /dev/pm6lvoriA 1048576 498016 53% 7 1% /oracle/PM6/origlogA /dev/pm6lvoriB 1048576 523392 51% 5 1% /oracle/PM6/origlogB
/dev/pm6lvdata1 614203392 216796752 65% 18 1% /oracle/PM6/sapdata1 /dev/pm6lvdata2 614203392 220892744 65% 15 1% /oracle/PM6/sapdata2 /dev/pm6lvdata3 614203392 220892776 65% 15 1% /oracle/PM6/sapdata3 /dev/pm6lvdata4 614203392 282332768 55% 15 1% /oracle/PM6/sapdata4 /dev/pm6lvdata5 614203392 282307456 55% 17 1% /oracle/PM6/sapdata5 /dev/pm6lvdata6 81788928 71944792 13% 5 1% /oracle/PM6/sapdata6 /dev/pm6lvsapreog 4063232 4061944 1% 4 1% /oracle/PM6/sapreorg /dev/pm6lvorastg 17039360 6638064 62% 11045 2% /oracle/stage /dev/pm6lvmnt 12845056 7322672 43% 196304 20% /sapmnt/PM6 /dev/pm6lvmntpool 127664128 89669320 30% 86025 1% /sapmnt/PM6/global/600SPOOL /dev/pm6lvusrsap 6029312 6018688 1% 17 1% /usr/sap /dev/pm6lvusap 20447232 13988544 32% 575 1% /usr/sap/PM6 /dev/pm6lvdveb 16252928 16249792 1% 3 1% /usr/sap/PM6/DVEBMGS00/work/tri /dev/pm6lvarching 61341696 35740608 42% 305 1% /usr/sap/archiving /dev/pm6lvstrans 32768000 6765232 80% 90811 11% /usr/sap/trans nimad2p3: /export/nim/outils 124780544 60316872 52% 51790 1% /mnt
8/17/2019 CLUSTER - AIX - Installation de HACMP_eng
http://slidepdf.com/reader/full/cluster-aix-installation-de-hacmpeng 62/93
PowerHA 5.4 installation record
Technical dossier of PowerHA 5.4 installation
CLUSTER - AIX - Installation de HACMP_eng Technical paper 626293
================================================================================ COMMAND: mount ================================================================================ node mounted mounted over vfs dates options
-------- --------------- --------------- ------ ------------ --------------- /dev/hd4/jfs October 2nd, 08 17:59 rw, log=/dev/hd8
/dev/hd2 /usr jfs October 2nd, 08 17:59 rw, log=/dev/hd8
/dev/hd9var /var jfs October 2nd, 08 17:59 rw, log=/dev/hd8
/dev/hd3 /tmp jfs October 2nd, 08 17:59 rw, log=/dev/hd8 /dev/hd11admin /admin jfs October 2nd, 08 17:59 rw, log=/dev/hd8
/proc /proc procfs Oct. 08 17:59 rw
/dev/hd10opt /opt jfs October 2nd, 08 17:59 rw, log=/dev/hd8
/dev/lvusers /usersconnect jfs October 2nd, 08 17:59 rw, log=/dev/hd8 /dev/lvfs01 /FS01 jfs October 2nd, 08 17:59 rw, log=/dev/logvgfs01
/dev/lvfs80 /FS80 jfs October 2nd, 08 17:59 rw, log=/dev/logvgfs01
/dev/lv_tempo /TEMPO jfs October 2nd, 08 17:59 rw, log=/dev/loglv00
/dev/pm6lvcft /FS01/logiciel/cft jfs2 Oct. 08 18:09 rw, log=/dev/log_PM6log
/dev/pm6lvdazl /FS01/logiciel/hpos jfs2 Oct. 08 18:09 rw,log=/dev/log_PM6log
/dev/pm6lvadm /home/pm6adm jfs October 2nd, 08 18:09 rw, log=/dev/log_PM6log
/dev/pm6lvint /inter jfs October 2nd, 08 18:09 rw, log=/dev/log_PM6redo
/dev/pm6lvscan /invscan jfs October 2nd, 08 18:09 rw, log=/dev/log_PM6redo
/dev/PM6_lvora /oracle jfs October 2nd, 08 18:09 rw, cio,log=/dev/log_PM6log
/dev/lvorapm6 /oracle/PM6 jfs October 2nd, 08 18:09 rw, log=/dev/log_PM6log
/dev/pm6lvmirA /oracle/PM6/mirrlogA jfs2 Oct. 08 18:09 rw, cio,log=/dev/log_PM6redo
/dev/pm6lvmirB /oracle/PM6/mirrlogB jfs2 Oct. 08 18:09 rw, cio,log=/dev/log_PM6redo
/dev/pm6lvorarch /oracle/PM6/oraarch jfs2 Oct. 08 18:09 rw,log=/dev/log_PM6log
/dev/pm6lvoriA /oracle/PM6/origlogA jfs2 Oct. 08 18:09 rw, cio,log=/dev/log_PM6redo
/dev/pm6lvoriB /oracle/PM6/origlogB jfs2 Oct. 08 18:09 rw, cio,
log=/dev/log_PM6redo /dev/pm6lvdata1 /oracle/PM6/sapdata1 jfs2 Oct. 08 18:09 rw, cio,
log=/dev/log_PM6dat1 /dev/pm6lvdata2 /oracle/PM6/sapdata2 jfs2 Oct. 08 18:09 rw, cio,
log=/dev/log_PM6dat1 /dev/pm6lvdata3 /oracle/PM6/sapdata3 jfs2 Oct. 08 18:09 rw, cio,
log=/dev/log_PM6dat2 /dev/pm6lvdata4 /oracle/PM6/sapdata4 jfs2 Oct. 08 18:09 rw, cio,
log=/dev/log_PM6dat2 /dev/pm6lvdata5 /oracle/PM6/sapdata5 jfs2 Oct. 08 18:09 rw, cio,
log=/dev/log_PM6dat3 /dev/pm6lvdata6 /oracle/PM6/sapdata6 jfs2 Oct. 08 18:09 rw, cio,
log=/dev/log_PM6dat3 /dev/pm6lvsapreog /oracle/PM6/sapreorg jfs2 Oct. 08 18:09 rw,
log=/dev/log_PM6log
8/17/2019 CLUSTER - AIX - Installation de HACMP_eng
http://slidepdf.com/reader/full/cluster-aix-installation-de-hacmpeng 63/93
PowerHA 5.4 installation record
Technical dossier of PowerHA 5.4 installation
CLUSTER - AIX - Installation de HACMP_eng Technical paper 636393
/dev/pm6lvorastg /oracle/stage jfs October 2nd, 08 18:09 rw,log=/dev/log_PM6redo
/dev/pm6lvmnt /sapmnt/PM6 jfs October 2nd, 08 18:09 rw, log=/dev/log_PM6log
/dev/pm6lvmntpool /sapmnt/PM6/global/600SPOOL jfs2 Oct. 08 18:09 rw,log=/dev/log_PM6log
/dev/pm6lvusrsap /usr/sap jfs October 2nd, 08 18:09 rw, log=/dev/log_PM6log
/dev/pm6lvusap /usr/sap/PM6 jfs October 2nd, 08 18:09 rw,log=/dev/log_PM6log
/dev/pm6lvdveb /usr/sap/PM6/DVEBMGS00/work/tri jfs2 Oct. 08 18:09 rw,log=/dev/log_PM6redo
/dev/pm6lvarching /usr/sap/archiving jfs2 Oct. 08 18:09 rw,log=/dev/log_PM6log
/dev/pm6lvstrans /usr/sap/trans jfs October 2nd, 08 18:09 rw,log=/dev/log_PM6log nimad2p3 /export/nim/outils /mnt NFS November 3rd, 02 16:25
================================================================================ COMMAND: exportfs ================================================================================ exportfs: nothing exported
================================================================================ COMMAND: lsfs ================================================================================
Name Nodename Mount Pt VFS Size Options Accounting Car /dev/hd4 -- /jfs2 2883584 -- yes No /dev/hd2 -- /usr jfs2 6029312 -- yes No /dev/hd9var -- /var jfs2 2359296 -- yes No /dev/hd3 -- /tmp jfs2 4456448 -- yes No /dev/hd11admin -- /admin jfs2 262144 -- yes No /proc -- /proc procfs -- -- yes No /dev/hd10opt -- /opt jfs2 262144 -- yes No /dev/lvusers -- /usersconnect jfs2 2097152 rw yes No /dev/lvfs01 -- /FS01 jfs2 13762560 -- yes No /dev/lvfs80 -- /FS80 jfs2 19005440 -- yes No /dev/pm6lvscan -- /invscan jfs2 1835008 rw No No /dev/pm6lvint -- /inter jfs2 1835008 rw No No
/dev/pm6lvdveb -- /usr/sap/PM6/DVEBMGS00/work/tri jfs2 16252928 rw NoNo /dev/pm6lvmirA -- /oracle/PM6/mirrlogA jfs2 1048576 cios, rw No No /dev/pm6lvmirB -- /oracle/PM6/mirrlogB jfs2 1048576 cios, rw No No /dev/pm6lvoriB -- /oracle/PM6/origlogB jfs2 1048576 cios, rw No No /dev/pm6lvoriA -- /oracle/PM6/origlogA jfs2 1048576 cios, rw No No /dev/pm6lvorastg -- /oracle/stage jfs2 17039360 rw No No /dev/pm6lvdata1 -- /oracle/PM6/sapdata1 jfs2 614203392 cios, rw No No /dev/pm6lvdata2 -- /oracle/PM6/sapdata2 jfs2 614203392 cios, rw No No /dev/pm6lvdata3 -- /oracle/PM6/sapdata3 jfs2 614203392 cios, rw No No /dev/pm6lvdata4 -- /oracle/PM6/sapdata4 jfs2 614203392 cios, rw No No /dev/pm6lvdata5 -- /oracle/PM6/sapdata5 jfs2 614203392 cios, rw No No /dev/lv_tempo -- /TEMPO jfs2 524288000 rw yes No /dev/pm6lvdata6 -- /oracle/PM6/sapdata6 jfs2 81788928 cios, rw No No /dev/PM6_lvora -- /oracle jfs2 5242880 cios, rw No No /dev/lvorapm6 -- /oracle/PM6 jfs2 12058624 rw No No /dev/pm6lvorarch -- /oracle/PM6/oraarch jfs2 123731968 rw No No
8/17/2019 CLUSTER - AIX - Installation de HACMP_eng
http://slidepdf.com/reader/full/cluster-aix-installation-de-hacmpeng 64/93
8/17/2019 CLUSTER - AIX - Installation de HACMP_eng
http://slidepdf.com/reader/full/cluster-aix-installation-de-hacmpeng 65/93
PowerHA 5.4 installation record
Technical dossier of PowerHA 5.4 installation
CLUSTER - AIX - Installation de HACMP_eng Technical paper 656593
5.4.1.0 MADE SUPPLEMENTS 9/6/09 11:31: 49
5.4.1.4 MADE SUPPLEMENTS 9/6/09 11:31: 49
cluster.es.cl ient. rte
5.4.0.0 MADE SUPPLEMENTS 9/6/09 11:29: 22 5.4.1.0 MADE SUPPLEMENTS 9/6/09 11:31: 49
5.4.1.5 MADE SUPPLEMENTS 9/6/09 11:31: 49
cluster.es.cl ient.utils
5.4.0.0 MADE SUPPLEMENTS 9/6/09 11:29: 22
5.4.1.0 MADE SUPPLEMENTS 9/6/09 11:31: 49
5.4.1.5 MADE SUPPLEMENTS 9/6/09 11:31: 49
cluster.es.cl ient. wsm
5.4.0.0 MADE SUPPLEMENTS 9/6/09 11:29: 22
5.4.1.0 MADE SUPPLEMENTS 9/6/09 11:31: 49
5.4.1.5 MADE SUPPLEMENTS 9/6/09 11:31: 49
cluster.es.cs poc.cmds
5.4.0.0 MADE SUPPLEMENTS 9/6/09 11:29: 19
5.4.1.0 MADE SUPPLEMENTS 9/6/09 11:31: 49
5.4.1.5 MADE SUPPLEMENTS 9/6/09 11:31: 49
cluster.es.cs poc. dsh
5.4.0.0 MADE SUPPLEMENTS 9/6/09 11:29: 19
5.4.1.0 MADE SUPPLEMENTS 9/6/09 11:31: 49
cluster.es.cs poc. rte
5.4.0.0 MADE SUPPLEMENTS 9/6/09 11:29: 19
5.4.1.0 MADE SUPPLEMENTS 9/6/09 11:31: 49
5.4.1.3 MADE SUPPLEMENTS 9/6/09 11:31: 49
cluster.es.pl ugins.dhcp 5.4.0.0 MADE SUPPLEMENTS 9/6/09 11:29: 18
5.4.1.0 MADE SUPPLEMENTS 9/6/09 11:31: 49
cluster.es.pl ugins. dns
5.4.0.0 MADE SUPPLEMENTS 9/6/09 11:29: 18
5.4.1.0 MADE SUPPLEMENTS 9/6/09 11:31: 49
cluster.es.pl ugins.printserver
5.4.0.0 MADE SUPPLEMENTS 9/6/09 11:29: 18
5.4.1.0 MADE SUPPLEMENTS 9/6/09 11:31: 49
cluster.es.se rver.cfgast
8/17/2019 CLUSTER - AIX - Installation de HACMP_eng
http://slidepdf.com/reader/full/cluster-aix-installation-de-hacmpeng 66/93
PowerHA 5.4 installation record
Technical dossier of PowerHA 5.4 installation
CLUSTER - AIX - Installation de HACMP_eng Technical paper 666693
5.4.0.0 MADE SUPPLEMENTS 9/6/09 11:29: 22
5.4.1.0 MADE SUPPLEMENTS 9/6/09 11:31: 49
cluster.es.se rver.diag
5.4.0.0 MADE SUPPLEMENTS 9/6/09 11:29: 22 5.4.1.0 MADE SUPPLEMENTS 9/6/09 11:31: 49
5.4.1.5 MADE SUPPLEMENTS 9/6/09 11:31: 49
cluster.es.se rver.events
5.4.0.0 MADE SUPPLEMENTS 9/6/09 11:29: 22
5.4.1.0 MADE SUPPLEMENTS 9/6/09 11:31: 49
5.4.1.5 MADE SUPPLEMENTS 9/6/09 11:31: 49
cluster.es.se rver. rte
5.4.0.0 MADE SUPPLEMENTS 9/6/09 11:29: 22
5.4.1.0 MADE SUPPLEMENTS 9/6/09 11:31: 49
5.4.1.5 MADE SUPPLEMENTS 9/6/09 11:31: 49
cluster.es.se rver.testtool
5.4.0.0 MADE SUPPLEMENTS 9/6/09 11:29: 22
5.4.1.0 MADE SUPPLEMENTS 9/6/09 11:31: 49
5.4.1.1 MADE SUPPLEMENTS 9/6/09 11:31: 49
cluster.es.se rver.utils
5.4.0.0 MADE SUPPLEMENTS 9/6/09 11:29: 22
5.4.1.0 MADE SUPPLEMENTS 9/6/09 11:31: 49
5.4.1.5 MADE SUPPLEMENTS 9/6/09 11:31: 49
cluster.es.wo rksheets
5.4.0.0 MADE SUPPLEMENTS 9/6/09 11:29: 18
5.4.1.0 MADE SUPPLEMENTS 9/6/09 11:31: 49
5.4.1.3 MADE SUPPLEMENTS 9/6/09 11:31: 49
cluster.license
5.4.0.0 MADE SUPPLEMENTS 9/6/09 11:29: 18 5.4.1.0 MADE SUPPLEMENTS 9/6/09 11:31: 49
5.4.1.1 MADE SUPPLEMENTS 9/6/09 11:31: 49
Path: /etc/objrepos cluster.es.cl ient. lib
5.4.0.0 MADE SUPPLEMENTS 9/6/09 11:29: 34
5.4.1.0 MADE SUPPLEMENTS 9/6/09 11:31: 49
5.4.1.4 MADE SUPPLEMENTS 9/6/09 11:31: 49
cluster.es.cl ient. rte
5.4.0.0 MADE SUPPLEMENTS 9/6/09 11:29: 34
8/17/2019 CLUSTER - AIX - Installation de HACMP_eng
http://slidepdf.com/reader/full/cluster-aix-installation-de-hacmpeng 67/93
PowerHA 5.4 installation record
Technical dossier of PowerHA 5.4 installation
CLUSTER - AIX - Installation de HACMP_eng Technical paper 676793
5.4.1.0 MADE SUPPLEMENTS 9/6/09 11:31: 49
5.4.1.5 MADE SUPPLEMENTS 9/6/09 11:31: 49
cluster.es.cs poc. rte
5.4.0.0 MADE SUPPLEMENTS 9/6/09 11:29: 21
cluster.es.se rver.diag
5.4.0.0 MADE SUPPLEMENTS 9/6/09 11:29: 34
cluster.es.se rver.events
5.4.0.0 MADE SUPPLEMENTS 9/6/09 11:29: 34
cluster.es.se rver. rte
5.4.0.0 MADE SUPPLEMENTS 9/6/09 11:29: 34
5.4.1.0 MADE SUPPLEMENTS 9/6/09 11:31: 49
5.4.1.5 MADE SUPPLEMENTS 9/6/09 11:31: 49
cluster.es.se rver.utils
5.4.0.0 MADE SUPPLEMENTS 9/6/09 11:29: 34
5.4.1.5 MADE SUPPLEMENTS 9/6/09 11:31: 49
Path: /usr/share/lib/objrepos
cluster.man.en_US.es.da your 5.4.0.0 MADE SUPPLEMENTS 9/6/09 11:29: 17
5.4.1.0 MADE SUPPLEMENTS 9/6/09 11:31: 49
5.4.1.3 MADE SUPPLEMENTS 9/6/09 11:31: 49
================================================================================ COMMAND: ifconfig en0 ================================================================================ en0: flags=1e080863,480<UP, BROADCAST, NOTRAILERS, RUNNING, SIMPLEX, multicast,
GROUPRT, 64BIT, CHECKSUM_OFFLOAD (ACTIVATES), CHAIN> inet 7.27.224.62 netmask 0xffffff00 broadcast 7.27.224.255
inet 192.168.40.191 netmask 0xffffff00 broadcast 192.168.40.255 inet 192.168.40.190 netmask 0xffffff00 broadcast 192.168.40.255 tcp_sendspace 262144 tcp_recvspace 262144 rfc1323 1
================================================================================ COMMAND: ifconfig lo0 ================================================================================ lo0: flags=e08084b<UP, BROADCAST, LOOPBACK, RUNNING, SIMPLEX, multicast,GROUPRT, 64BIT>
inet 127.0.0.1 netmask 0xff000000 broadcast 127.255.255.255
inet6:: 1/0
tcp_sendspace 131072 tcp_recvspace 131072 rfc1323 1
================================================================================ COMMAND: lsvg - L VGCL_PM6redo
8/17/2019 CLUSTER - AIX - Installation de HACMP_eng
http://slidepdf.com/reader/full/cluster-aix-installation-de-hacmpeng 68/93
PowerHA 5.4 installation record
Technical dossier of PowerHA 5.4 installation
CLUSTER - AIX - Installation de HACMP_eng Technical paper 686893
================================================================================ VGCL_PM6redo: STANDARD LV NAME LPs PPs special minutes LV STATE MOUNT NOT pm6lvscan jfs2 7 14 2 open/syncd /invscan log_PM6redo jfs2log 1 2 2 open/syncd N/A pm6lvint jfs2 7 14 2 open/syncd /inter pm6lvdveb jfs2 62 124 2 open/syncd /usr/sap/PM6/DVEBMGS00/work/tri pm6lvmirA jfs2 4 8 2 open/syncd /oracle/PM6/mirrlogA pm6lvmirB jfs2 4 8 2 open/syncd /oracle/PM6/mirrlogB pm6lvoriB jfs2 4 8 2 open/syncd /oracle/PM6/origlogB pm6lvoriA jfs2 4 8 2 open/syncd /oracle/PM6/origlogA pm6lvorastg jfs2 65 130 2 open/syncd /oracle/stage
================================================================================ COMMAND: lsvg - L VGCL_PM6log ================================================================================ VGCL_PM6log: STANDARD LV NAME LPs PPs special minutes LV STATE MOUNT NOT log_PM6log jfs2log 1 2 2 open/syncd N/A PM6_lvora jfs2 40 80 2 open/syncd /oracle lvorapm6 jfs2 92 184 2 open/syncd /oracle/PM6 pm6lvorarch jfs2 944 1888 6 open/syncd /oracle/PM6/oraarch pm6lvsapreog jfs2 31 62 2 open/syncd /oracle/PM6/sapreorg pm6lvmnt jfs2 98 196 2 open/syncd /sapmnt/PM6 pm6lvmntpool jfs2 974 1948 7 open/syncd /sapmnt/PM6/global/600SPOOL pm6lvusrsap jfs2 46 92 2 open/syncd /usr/sap pm6lvusap jfs2 156 312 2 open/syncd /usr/sap/PM6 pm6lvstrans jfs2 250 500 2 open/syncd /usr/sap/trans pm6lvadm jfs2 7 14 2 open/syncd /home/pm6adm pm6lvarching jfs2 468 936 4 open/syncd /usr/sap/archiving pm6lvcft jfs2 15 30 2 open/syncd /FS01/logiciel/cft pm6lvdazl jfs2 31 62 2 open/syncd /FS01/logiciel/hpos
================================================================================ COMMAND: lsvg - L VGCL_PM6dat3 ================================================================================ VGCL_PM6dat3: STANDARD LV NAME LPs PPs special minutes LV STATE MOUNT NOT pm6lvdata5 jfs2 2343 4686 6 open/syncd /oracle/PM6/sapdata5 log_PM6dat3 jfs2log 1 2 2 open/syncd N/A pm6lvdata6 jfs2 312 624 2 open/syncd /oracle/PM6/sapdata6
================================================================================ COMMAND: lsvg - L VGCL_PM6dat2 ================================================================================ VGCL_PM6dat2: STANDARD LV NAME LPs PPs special minutes LV STATE MOUNT NOT pm6lvdata3 jfs2 2343 4686 6 open/syncd /oracle/PM6/sapdata3 log_PM6dat2 jfs2log 1 2 2 open/syncd N/A pm6lvdata4 jfs2 2343 4686 6 open/syncd /oracle/PM6/sapdata4
================================================================================
COMMAND: lsvg - L VGCL_PM6dat1 ================================================================================ VGCL_PM6dat1: STANDARD LV NAME LPs PPs special minutes LV STATE MOUNT NOT
8/17/2019 CLUSTER - AIX - Installation de HACMP_eng
http://slidepdf.com/reader/full/cluster-aix-installation-de-hacmpeng 69/93
PowerHA 5.4 installation record
Technical dossier of PowerHA 5.4 installation
CLUSTER - AIX - Installation de HACMP_eng Technical paper 696993
pm6lvdata1 jfs2 2343 4686 6 open/syncd /oracle/PM6/sapdata1 log_PM6dat1 jfs2log 1 2 2 open/syncd N/A pm6lvdata2 jfs2 2343 4686 6 open/syncd /oracle/PM6/sapdata2
================================================================================ COMMAND: lsvg - L VG_TEMPO ================================================================================ VG_TEMPO: STANDARD LV NAME LPs PPs special minutes LV STATE MOUNT NOT lv_tempo jfs2 1000 1000 3 open/syncd /TEMPO open loglv00 jfs2log 1 1 1/syncd N/A
================================================================================ COMMAND: lsvg - L FS01vg ================================================================================ FS01vg: STANDARD LV NAME LPs PPs special minutes LV STATE MOUNT NOT open logvgfs01 jfs2log 1 1 1/syncd N/A lvfs01 jfs2 210 210 1 open/syncd /FS01 lvfs80 jfs2 290 290 1 open/syncd /FS80
================================================================================ COMMAND: lsvg - L rootvg ================================================================================ rootvg: STANDARD LV NAME LPs PPs special minutes LV STATE MOUNT NOT
hd5 bootup 1 1 1 closed/syncd N/A hd6 paging 235 235 1 open/syncd N/A open hd8 jfs2log 1 1 1/syncd N/A hd4 jfs2 11 11 1 open/syncd/ hd2 jfs2 23 23 1 open/syncd /usr hd9var jfs2 9 9 1 open/syncd /var hd3 jfs2 17 17 1 open/syncd /tmp open hd10opt jfs2 1 1 1/syncd /opt open hd11admin jfs2 1 1 1/syncd /admin lg_dumplv sysdump 32 32 1 open/syncd N/A lvusers jfs2 8 8 1 open/syncd /usersconnect
================================================================================
COMMAND: lslv - L pm6lvscan ================================================================================ pm6lvscan: /invscan STATEMENT COPIES IN BAND DISTRIBUTION hdisk6 007:000: 000 100% 000:007: 000:000: 000 hdisk24 007:000: 000 100% 000:007: 000:000: 000
================================================================================ COMMAND: lslv - L log_PM6redo ================================================================================ log_PM6redo: N/A STATEMENT COPIES IN BAND DISTRIBUTION hdisk6 001:000: 000 100% 000:001: 000:000: 000 hdisk24 001:000: 000 0% 000:000: 000:000: 001
================================================================================
8/17/2019 CLUSTER - AIX - Installation de HACMP_eng
http://slidepdf.com/reader/full/cluster-aix-installation-de-hacmpeng 70/93
PowerHA 5.4 installation record
Technical dossier of PowerHA 5.4 installation
CLUSTER - AIX - Installation de HACMP_eng Technical paper 707093
COMMAND: lslv - L pm6lvint ================================================================================ pm6lvint: /inter STATEMENT COPIES IN BAND DISTRIBUTION hdisk6 007:000: 000 100% 000:007: 000:000: 000 hdisk24 007:000: 000 100% 000:007: 000:000: 000
================================================================================ COMMAND: lslv - L pm6lvdveb ================================================================================ pm6lvdveb: /usr/sap/PM6/DVEBMGS00/work/tri STATEMENT COPIES IN BAND DISTRIBUTION hdisk6 062:000: 000 27% 000:017: 031:014: 000
hdisk24 062:000: 000 29% 000:018: 031:013: 000
================================================================================ COMMAND: lslv - L pm6lvmirA ================================================================================ pm6lvmirA: /oracle/PM6/mirrlogA
STATEMENT COPIES IN BAND DISTRIBUTION hdisk6 004:000: 000 0% 004:000: 000:000: 000 hdisk24 004:000: 000 0% 004:000: 000:000: 000
================================================================================ COMMAND: lslv - L pm6lvmirB ================================================================================ pm6lvmirB: /oracle/PM6/mirrlogB STATEMENT COPIES IN BAND DISTRIBUTION hdisk6 004:000: 000 0% 004:000: 000:000: 000 hdisk24 004:000: 000 0% 004:000: 000:000: 000
================================================================================ COMMAND: lslv - L pm6lvoriB ================================================================================ pm6lvoriB: /oracle/PM6/origlogB
STATEMENT COPIES IN BAND DISTRIBUTION hdisk6 004:000: 000 0% 004:000: 000:000: 000 hdisk24 004:000: 000 0% 004:000: 000:000: 000
================================================================================ COMMAND: lslv - L pm6lvoriA ================================================================================ pm6lvoriA: /oracle/PM6/origlogA STATEMENT COPIES IN BAND DISTRIBUTION hdisk6 004:000: 000 0% 004:000: 000:000: 000 hdisk24 004:000: 000 0% 004:000: 000:000: 000
================================================================================ COMMAND: lslv - L pm6lvorastg ================================================================================
pm6lvorastg: /oracle/stage STATEMENT COPIES IN BAND DISTRIBUTION hdisk6 065:000: 000 0% 016:000: 000:018: 031 hdisk24 065:000: 000 0% 016:000: 000:019: 030
8/17/2019 CLUSTER - AIX - Installation de HACMP_eng
http://slidepdf.com/reader/full/cluster-aix-installation-de-hacmpeng 71/93
PowerHA 5.4 installation record
Technical dossier of PowerHA 5.4 installation
CLUSTER - AIX - Installation de HACMP_eng Technical paper 717193
================================================================================ COMMAND: lslv - L log_PM6log ================================================================================ log_PM6log: N/A STATEMENT COPIES IN BAND DISTRIBUTION hdisk2 001:000: 000 0% 001:000: 000:000: 000 hdisk3 001:000: 000 0% 001:000: 000:000: 000
================================================================================ COMMAND: lslv - L PM6_lvora ================================================================================ PM6_lvora: /oracle
STATEMENT COPIES IN BAND DISTRIBUTION hdisk2 040:000: 000 0% 040:000: 000:000: 000 hdisk3 040:000: 000 0% 040:000: 000:000: 000
================================================================================ COMMAND: lslv - L lvorapm6 ================================================================================ lvorapm6: /oracle/PM6 STATEMENT COPIES IN BAND DISTRIBUTION hdisk5 092:000: 000 100% 000:092: 000:000: 000 hdisk23 092:000: 000 100% 000:092: 000:000: 000
================================================================================ COMMAND: lslv - L pm6lvorarch ================================================================================ pm6lvorarch: /oracle/PM6/oraarch STATEMENT COPIES IN BAND DISTRIBUTION hdisk14 355:000: 000 28% 103:102: 102:006: 042 hdisk33 355:000: 000 28% 103:102: 102:006: 042 hdisk44 511:000: 000 19% 103:102: 102:102: 102 hdisk45 511:000: 000 19% 103:102: 102:102: 102 hdisk2 036:000: 000 0% 001:000: 000:025: 010 hdisk3 120:000: 000 0% 001:000: 000:025: 094
================================================================================
COMMAND: lslv - L pm6lvsapreog ================================================================================ pm6lvsapreog: /oracle/PM6/sapreorg STATEMENT COPIES IN BAND DISTRIBUTION hdisk5 031:000: 000 0% 031:000: 000:000: 000 hdisk23 031:000: 000 0% 031:000: 000:000: 000
================================================================================ COMMAND: lslv - L pm6lvmnt ================================================================================ pm6lvmnt: /sapmnt/PM6 STATEMENT COPIES IN BAND DISTRIBUTION
hdisk5 098:000: 000 0% 000:000: 000:098: 000 hdisk23 098:000: 000 0% 000:000: 000:098: 000
================================================================================
8/17/2019 CLUSTER - AIX - Installation de HACMP_eng
http://slidepdf.com/reader/full/cluster-aix-installation-de-hacmpeng 72/93
8/17/2019 CLUSTER - AIX - Installation de HACMP_eng
http://slidepdf.com/reader/full/cluster-aix-installation-de-hacmpeng 73/93
PowerHA 5.4 installation record
Technical dossier of PowerHA 5.4 installation
CLUSTER - AIX - Installation de HACMP_eng Technical paper 737393
================================================================================ COMMAND: lslv - L pm6lvcft ================================================================================ pm6lvcft: /FS01/logiciel/cft STATEMENT COPIES IN BAND DISTRIBUTION hdisk2 015:000: 000 0% 015:000: 000:000: 000 hdisk3 015:000: 000 0% 015:000: 000:000: 000
================================================================================ COMMAND: lslv - L pm6lvdazl ================================================================================ pm6lvdazl: /FS01/logiciel/hpos STATEMENT COPIES IN BAND DISTRIBUTION
hdisk2 031:000: 000 0% 000:000: 000:031: 000 hdisk3 031:000: 000 0% 000:000: 000:031: 000
================================================================================ COMMAND: lslv - L pm6lvdata5 ================================================================================ pm6lvdata5: /oracle/PM6/sapdata5 STATEMENT COPIES IN BAND DISTRIBUTION hdisk12 1023:000: 000 20% 205:205: 204:204: 205 hdisk30 1023:000: 000 20% 205:205: 204:204: 205 hdisk20 1023:000: 000 20% 205:205: 204:204: 205 hdisk39 1023:000: 000 20% 205:205: 204:204: 205 hdisk21 297:000: 000 69% 000:205: 092:000: 000 hdisk40 297:000: 000 69% 000:205: 092:000: 000
================================================================================ COMMAND: lslv - L log_PM6dat3 ================================================================================ log_PM6dat3: N/A STATEMENT COPIES IN BAND DISTRIBUTION hdisk21 001:000: 000 0% 001:000: 000:000: 000 hdisk40 001:000: 000 0% 001:000: 000:000: 000
================================================================================ COMMAND: lslv - L pm6lvdata6
================================================================================ pm6lvdata6: /oracle/PM6/sapdata6 STATEMENT COPIES IN BAND DISTRIBUTION hdisk21 312:000: 000 0% 000:000: 112:200: 000 hdisk40 312:000: 000 0% 000:000: 112:200: 000
================================================================================ COMMAND: lslv - L pm6lvdata3 ================================================================================ pm6lvdata3: /oracle/PM6/sapdata3 STATEMENT COPIES IN BAND DISTRIBUTION hdisk9 1023:000: 000 20% 205:205: 204:204: 205 hdisk27 1023:000: 000 20% 205:205: 204:204: 205 hdisk10 1023:000: 000 20% 205:205: 204:204: 205 hdisk28 1023:000: 000 20% 205:205: 204:204: 205 hdisk11 297:000: 000 69% 000:205: 092:000: 000
8/17/2019 CLUSTER - AIX - Installation de HACMP_eng
http://slidepdf.com/reader/full/cluster-aix-installation-de-hacmpeng 74/93
PowerHA 5.4 installation record
Technical dossier of PowerHA 5.4 installation
CLUSTER - AIX - Installation de HACMP_eng Technical paper 747493
hdisk29 297:000: 000 69% 000:205: 092:000: 000
================================================================================ COMMAND: lslv - L log_PM6dat2 ================================================================================ log_PM6dat2: N/A STATEMENT COPIES IN BAND DISTRIBUTION hdisk37 001:000: 000 100% 000:001: 000:000: 000 hdisk19 001:000: 000 0% 001:000: 000:000: 000
================================================================================ COMMAND: lslv - L pm6lvdata4 ================================================================================
pm6lvdata4: /oracle/PM6/sapdata4 STATEMENT COPIES IN BAND DISTRIBUTION hdisk11 726:000: 000 0% 205:000: 112:204: 205 hdisk29 726:000: 000 0% 205:000: 112:204: 205 hdisk18 1023:000: 000 20% 205:205: 204:204: 205 hdisk37 1022:000: 000 19% 205:204: 204:204: 205 hdisk38 595:000: 000 34% 186:205: 204:000: 000 hdisk19 594:000: 000 34% 185:205: 204:000: 000
================================================================================ COMMAND: lslv - L pm6lvdata1 ================================================================================ pm6lvdata1: /oracle/PM6/sapdata1
STATEMENT COPIES IN BAND DISTRIBUTION hdisk7 1022:000: 000 19% 205:204: 204:204: 205 hdisk25 1022:000: 000 19% 205:204: 204:204: 205 hdisk8 1022:000: 000 19% 205:204: 204:204: 205 hdisk26 1022:000: 000 19% 205:204: 204:204: 205 hdisk15 299:000: 000 68% 000:204: 095:000: 000 hdisk34 299:000: 000 68% 000:204: 095:000: 000
================================================================================ COMMAND: lslv - L log_PM6dat1 ================================================================================ log_PM6dat1: N/A
STATEMENT COPIES IN BAND DISTRIBUTION hdisk36 001:000: 000 100% 000:001: 000:000: 000 hdisk17 001:000: 000 0% 001:000: 000:000: 000
================================================================================ COMMAND: lslv - L pm6lvdata2 ================================================================================ pm6lvdata2: /oracle/PM6/sapdata2 STATEMENT COPIES IN BAND DISTRIBUTION hdisk15 723:000: 000 0% 205:000: 109:204: 205 hdisk34 723:000: 000 0% 205:000: 109:204: 205 hdisk16 1022:000: 000 19% 205:204: 204:204: 205 hdisk35 1022:000: 000 19% 205:204: 204:204: 205
hdisk17 598:000: 000 34% 190:204: 204:000: 000 hdisk36 598:000: 000 33% 191:203: 204:000: 000
8/17/2019 CLUSTER - AIX - Installation de HACMP_eng
http://slidepdf.com/reader/full/cluster-aix-installation-de-hacmpeng 75/93
PowerHA 5.4 installation record
Technical dossier of PowerHA 5.4 installation
CLUSTER - AIX - Installation de HACMP_eng Technical paper 757593
================================================================================ COMMAND: lslv - L lv_tempo ================================================================================ lv_tempo: /TEMPO STATEMENT COPIES IN BAND DISTRIBUTION hdisk31 511:000: 000 19% 103:102: 102:102: 102 hdisk41 255:000: 000 20% 051:051: 051:051: 051 hdisk42 234:000: 000 21% 051:051: 051:051: 030
================================================================================ COMMAND: lslv - L loglv00 ================================================================================ loglv00: N/A
STATEMENT COPIES IN BAND DISTRIBUTION hdisk42 001:000: 000 0% 000:000: 000:000: 001
================================================================================ COMMAND: lslv - L logvgfs01 ================================================================================ logvgfs01: N/A STATEMENT COPIES IN BAND DISTRIBUTION hdisk22 001:000: 000 100% 000:001: 000:000: 000
================================================================================ COMMAND: lslv - L lvfs01 ================================================================================ lvfs01: /FS01 STATEMENT COPIES IN BAND DISTRIBUTION hdisk22 210:000: 000 24% 057:051: 102:000: 000
================================================================================ COMMAND: lslv - L lvfs80 ================================================================================ lvfs80: /FS80 STATEMENT COPIES IN BAND DISTRIBUTION hdisk22 290:000: 000 17% 046:050: 000:102: 092
================================================================================ COMMAND: lslv - L hd5 ================================================================================ hd5: N/A STATEMENT COPIES IN BAND DISTRIBUTION hdisk0 001:000: 000 100% 001:000: 000:000: 000
================================================================================ COMMAND: lslv - L hd6 ================================================================================ hd6: N/A STATEMENT COPIES IN BAND DISTRIBUTION hdisk0 235:000: 000 26% 102:062: 062:009: 000
================================================================================ COMMAND: lslv - L hd8
8/17/2019 CLUSTER - AIX - Installation de HACMP_eng
http://slidepdf.com/reader/full/cluster-aix-installation-de-hacmpeng 76/93
PowerHA 5.4 installation record
Technical dossier of PowerHA 5.4 installation
CLUSTER - AIX - Installation de HACMP_eng Technical paper 767693
================================================================================ hd8: N/A STATEMENT COPIES IN BAND DISTRIBUTION hdisk0 001:000: 000 100% 000:000: 001:000: 000
================================================================================ COMMAND: lslv - L hd4 ================================================================================ hd4: / STATEMENT COPIES IN BAND DISTRIBUTION hdisk0 011:000: 000 36% 000:000: 004:007: 000
================================================================================
COMMAND: lslv - L hd2 ================================================================================ hd2: /usr STATEMENT COPIES IN BAND DISTRIBUTION hdisk0 023:000: 000 100% 000:000: 023:000: 000
================================================================================ COMMAND: lslv - L hd9var ================================================================================ hd9var: /var STATEMENT COPIES IN BAND DISTRIBUTION hdisk0 009:000: 000 100% 000:000: 009:000: 000
================================================================================ COMMAND: lslv - L hd3 ================================================================================ hd3: /tmp STATEMENT COPIES IN BAND DISTRIBUTION hdisk0 017:000: 000 5% 000:000: 001:016: 000
================================================================================ COMMAND: lslv - L hd10opt ================================================================================ hd10opt: /opt STATEMENT COPIES IN BAND DISTRIBUTION hdisk0 001:000: 000 100% 000:000: 001:000: 000
================================================================================ COMMAND: lslv - L hd11admin ================================================================================ hd11admin: /admin STATEMENT COPIES IN BAND DISTRIBUTION hdisk0 001:000: 000 100% 000:000: 001:000: 000
================================================================================ COMMAND: lslv - L lg_dumplv ================================================================================
lg_dumplv: N/A STATEMENT COPIES IN BAND DISTRIBUTION hdisk0 032:000: 000 100% 000:032: 000:000: 000
8/17/2019 CLUSTER - AIX - Installation de HACMP_eng
http://slidepdf.com/reader/full/cluster-aix-installation-de-hacmpeng 77/93
PowerHA 5.4 installation record
Technical dossier of PowerHA 5.4 installation
CLUSTER - AIX - Installation de HACMP_eng Technical paper 777793
================================================================================ COMMAND: lslv - L lvusers ================================================================================ lvusers: /usersconnect STATEMENT COPIES IN BAND DISTRIBUTION hdisk0 008:000: 000 100% 000:008: 000:000: 000
================================================================================ COMMAND: odmget HACMPdaemons ================================================================================
HACMPdaemons:
nodename = “gtyxsappm6p1” daemon = “clstrmgr”
type = “start”
object = “manages”
been worth = “car”
HACMPdaemons: nodename = “gtyxsappm6p1”
daemon = “clstrmgr” type = “start”
object = “broadcast”
been worth = “true”
HACMPdaemons: nodename = “gtyxsappm6p1”
daemon = “clinfo”
type = “start”
object = “time”
been worth = “true”
HACMPdaemons: nodename = “gtyxsappm6p1”
daemon = “clstrmgrES”
type = “stop”
object = “time”
been worth = “now”
HACMPdaemons: nodename = “gtyxsappm6p1”
daemon = “clstrmgrES”
type = “stop”
object = “broadcast”
been worth = “false”
HACMPdaemons:
8/17/2019 CLUSTER - AIX - Installation de HACMP_eng
http://slidepdf.com/reader/full/cluster-aix-installation-de-hacmpeng 78/93
PowerHA 5.4 installation record
Technical dossier of PowerHA 5.4 installation
CLUSTER - AIX - Installation de HACMP_eng Technical paper 787893
nodename = “gtyxsappm6p1”
daemon = “clstrmgrES”
type = “stop”
object = “mode”
been worth = “forced”
HACMPdaemons:
nodename = “gtyxsappm6p1” daemon = “clstrmgr_scripts”
type = “resource_locator”
object = “RG_PM6”
been worth = “UP”
HACMPdaemons: nodename = ""
daemon = ""
type = “verify”
object = ""
been worth = “nun”
================================================================================ COMMAND: odmget HACMPsp2 ================================================================================
clsnapshot: Following information is retrieved from node: gtyxsappm6p2 -------------------------------------------------
================================================================================ COMMAND: netstat - I ================================================================================ Name MTU Network Address ZoneID Ipkts Ierrs Opkts Oerrs coll en0 1500 link-2 62.7e.db.3d.ea.14 - 3044970366 0 3188989200 0 0 en0 1500 7.27.224 gtyxsappm6p2_boots - 3044970366 0 3188989200 0 0 en0 1500 192.168.40 gtyxsappm6p2. pharma. avs - 3044970366 0 3188989200 0 0
lo0 16896 link-1 - 3585113 0 3589058 0 0 lo0 16896 127 loopback - 3585113 0 3589058 0 0 lo0 16896:: 1 3 3585113 0 3589058 0 0
================================================================================ COMMAND: netstat - in ================================================================================ Name MTU Network Address ZoneID Ipkts Ierrs Opkts Oerrs coll en0 1500 link-2 62.7e.db.3d.ea.14 - 3044970367 0 3188989200 0 0 en0 1500 7.27.224 7.27.224.63 - 3044970367 0 3188989200 0 0 en0 1500 192.168.40 192.168.40.192 - 3044970367 0 3188989200 0 0 lo0 16896 link-1 - 3585117 0 3589062 0 0 lo0 16896 127 127.0.0.1 - 3585117 0 3589062 0 0
lo0 16896:: 1 3 3585117 0 3589062 0 0
================================================================================
8/17/2019 CLUSTER - AIX - Installation de HACMP_eng
http://slidepdf.com/reader/full/cluster-aix-installation-de-hacmpeng 79/93
PowerHA 5.4 installation record
Technical dossier of PowerHA 5.4 installation
CLUSTER - AIX - Installation de HACMP_eng Technical paper 797993
COMMAND: No - has ================================================================================
arpqsize = 12 arpt_killc = 20
arptab_bsiz = 7
arptab_nb = 149
bcastping = 0
clean_partial_conns = 0
delayack = 0
delayackports = {}
dgd_packets_lost = 3
dgd_ping_time = 5 dgd_retry_time = 5
directed_broadcast = 0
fasttimo = 200
icmp6_errmsg_rate = 10
icmpaddressmask = 0 ie5_old_multicast_mapping = 0
ifsize = 256
ip6_defttl = 64
ip6_prune = 1
ip6forwarding = 0
ip6srcrouteforward = 1 ip_ifdelete_notify = 0
ip_nfrag = 200
ipforwarding=0
ipfragttl = 2
ipignoreredirects = 0
ipqmaxlen = 100
ipsendredirects=0
ipsrcrouteforward=1
ipsrcrouterecv = 1
ipsrcroutesend=1
llsleep_timeout = 3
lo_perf = 1
lowthresh = 90
main_if6 = 0
main_site6 = 0
maxnip6q = 20
maxttl = 255 medthresh = 95
mpr_policy = 1
multi_homed = 1
nbc_limit = 15073280 nbc_max_cache = 131072
nbc_min_cache = 1
8/17/2019 CLUSTER - AIX - Installation de HACMP_eng
http://slidepdf.com/reader/full/cluster-aix-installation-de-hacmpeng 80/93
PowerHA 5.4 installation record
Technical dossier of PowerHA 5.4 installation
CLUSTER - AIX - Installation de HACMP_eng Technical paper 808093
nbc_ofile_hashsz = 12841
nbc_pseg = 0
nbc_pseg_limit = 30146560
ndd_event_name = {Al}
ndd_event_tracing = 0
ndp_mmaxtries = 3
ndp_umaxtries = 3
ndpqsize = 50
ndpt_down = 3
ndpt_keep = 120
ndpt_probe = 5
ndpt_reachable = 30 ndpt_retrans = 1
net_buf_size = {Al}
net_buf_type = {Al} net_malloc_frag_mask = {0}
netm_page_promote = 1
nonlocsrcroute=1
nstrpush = 8
passive_dgd = 0
pmtu_default_age = 10
pmtu_expire = 10
pmtu_rediscover_interval = 30
psebufcalls = 20
psecache = 1
psetimers = 20
rfc1122addrchk = 0
rfc1323 = 0
rfc2414 = 1
route _expire = 1
routerevalidate=1
rto_high = 64
rto_length = 13 rto_limit = 7
rto_low = 1
sack = 0
sb_max = 1048576
send_file_duration = 300
site6_index = 0
sockthresh = 85
sodebug = 0
sodebug_env = 0
somaxconn = 1024 strctlsz = 1024
strmsgsz = 0
8/17/2019 CLUSTER - AIX - Installation de HACMP_eng
http://slidepdf.com/reader/full/cluster-aix-installation-de-hacmpeng 81/93
PowerHA 5.4 installation record
Technical dossier of PowerHA 5.4 installation
CLUSTER - AIX - Installation de HACMP_eng Technical paper 818193
strthresh = 85
strturncnt = 15
subnetsarelocal=0
tcp_bad_port_limit = 0
tcp_ecn = 0
tcp_ephemeral_high = 65535
tcp_ephemeral_low = 32768
tcp_finwait2 = 1200
tcp_icmpsecure = 0
tcp_init_window = 0
tcp_inpcb_hashtab_siz = 24499
tcp_keepcnt = 8 tcp_keepidle = 14400
tcp_keepinit = 150
tcp_keepintvl = 150 tcp_limited_transmit = 1
tcp_low_rto = 0
tcp_maxburst = 0
tcp_mssdflt = 1460
tcp_nagle_limit = 65535
tcp_nagleoverride = 0
tcp_ndebug = 100
tcp_newreno = 1
tcp_nodelayack = 0
tcp_pmtu_discover = 1
tcp_recvspace = 16384
tcp_sendspace = 16384
tcp_tcpsecure = 0
tcp_timewait = 1
tcp_ttl = 60
tcprexmtthresh = 3
tcptr_enable = 0
thewall = 60293120 timer_wheel_tick = 0
tn_filter = 1
udp_bad_port_limit = 0
udp_ephemeral_high = 65535
udp_ephemeral_low = 32768
udp_inpcb_hashtab_siz = 24499
udp_pmtu_discover = 1
udp_recvspace = 42080
udp_sendspace = 9216
udp_ttl = 30 udpcksum = 1
use_sndbufpool = 1
8/17/2019 CLUSTER - AIX - Installation de HACMP_eng
http://slidepdf.com/reader/full/cluster-aix-installation-de-hacmpeng 82/93
PowerHA 5.4 installation record
Technical dossier of PowerHA 5.4 installation
CLUSTER - AIX - Installation de HACMP_eng Technical paper 828293
================================================================================ COMMAND: clchsyncd ================================================================================ syncd frequency: 10 High toilets mark: 33 Low toilets mark: 24
================================================================================ COMMAND: lsdev - DC yew ================================================================================ en0 Available Standard Network Ethernet Interfaces et0 Defined IEEE 802.3 Network Ethernet Interfaces lo0 Available Loopback Network Interfaces
================================================================================ COMMAND: lsdev - DC disk ================================================================================ hdisk0 Available Virtual SCSI Disk Drive hdisk1 Available 12-T1-01 IBM MPIO FC 2107 hdisk2 Available 12-T1-01 IBM MPIO FC 2107 hdisk3 Available 12-T1-01 IBM MPIO FC 2107 hdisk4 Available 12-T1-01 IBM MPIO FC 2107 hdisk5 Available 12-T1-01 IBM MPIO FC 2107 hdisk6 Available 12-T1-01 IBM MPIO FC 2107 hdisk7 Available 12-T1-01 IBM MPIO FC 2107
hdisk8 Available 12-T1-01 IBM MPIO FC 2107 hdisk9 Available 12-T1-01 IBM MPIO FC 2107 hdisk10 Available 12-T1-01 IBM MPIO FC 2107 hdisk11 Available 12-T1-01 IBM MPIO FC 2107 hdisk12 Available 12-T1-01 IBM MPIO FC 2107 hdisk13 Available 12-T1-01 IBM MPIO FC 2107 hdisk14 Available 12-T1-01 IBM MPIO FC 2107 hdisk15 Available 12-T1-01 IBM MPIO FC 2107 hdisk16 Available 12-T1-01 IBM MPIO FC 2107 hdisk17 Available 12-T1-01 IBM MPIO FC 2107 hdisk18 Available 12-T1-01 IBM MPIO FC 2107 hdisk19 Available 12-T1-01 IBM MPIO FC 2107 hdisk20 Available 12-T1-01 IBM MPIO FC 2107 hdisk21 Available 12-T1-01 IBM MPIO FC 2107 hdisk22 Available 12-T1-01 IBM MPIO FC 2107 hdisk23 Available 12-T1-01 IBM MPIO FC 2107 hdisk24 Available 12-T1-01 IBM MPIO FC 2107 hdisk25 Available 12-T1-01 IBM MPIO FC 2107 hdisk26 Available 12-T1-01 IBM MPIO FC 2107 hdisk27 Available 12-T1-01 IBM MPIO FC 2107 hdisk28 Available 12-T1-01 IBM MPIO FC 2107 hdisk29 Available 12-T1-01 IBM MPIO FC 2107 hdisk30 Available 12-T1-01 IBM MPIO FC 2107 hdisk31 Available 12-T1-01 IBM MPIO FC 2107 hdisk32 Available 12-T1-01 IBM MPIO FC 2107 hdisk33 Available 12-T1-01 IBM MPIO FC 2107 hdisk34 Available 12-T1-01 IBM MPIO FC 2107 hdisk35 Available 12-T1-01 IBM MPIO FC 2107 hdisk36 Available 12-T1-01 IBM MPIO FC 2107 hdisk37 Available 12-T1-01 IBM MPIO FC 2107
8/17/2019 CLUSTER - AIX - Installation de HACMP_eng
http://slidepdf.com/reader/full/cluster-aix-installation-de-hacmpeng 83/93
PowerHA 5.4 installation record
Technical dossier of PowerHA 5.4 installation
CLUSTER - AIX - Installation de HACMP_eng Technical paper 838393
hdisk38 Available 12-T1-01 IBM MPIO FC 2107 hdisk39 Available 12-T1-01 IBM MPIO FC 2107 hdisk40 Available 12-T1-01 IBM MPIO FC 2107 hdisk41 Available 12-T1-01 IBM MPIO FC 2107 hdisk42 Available 12-T1-01 IBM MPIO FC 2107 hdisk43 Available 12-T1-01 IBM MPIO FC 2107 hdisk44 Available 12-T1-01 IBM MPIO FC 2107 hdisk45 Available 12-T1-01 IBM MPIO FC 2107 hdisk46 Available 12-T1-01 IBM MPIO FC 2107 hdisk47 Available 12-T1-01 IBM MPIO FC 2107
================================================================================ COMMAND: lsvg ================================================================================ rootvg VGCL_PM6redo VGCL_PM6log VGCL_HB_D3 VGCL_HB_D2 FS01vg VGCL_PM6dat1 VGCL_PM6dat2 VGCL_PM6dat3
================================================================================ COMMAND: lspv ================================================================================ hdisk0 00c6e0c4aa80463f rootvg active hdisk1 00c6e0d4c56889a7 VGCL_HB_D2 hdisk2 00c6e0d4c5688a8d VGCL_PM6log competitor hdisk3 00c6e0d4c5688bae VGCL_PM6log competitor hdisk4 00c6e0d4c5688caf VGCL_HB_D3 hdisk5 00c6e0c4ee73e0ac FS01vg active hdisk6 00c6e0d4ee533cc6 VGCL_PM6log competitor hdisk7 00c6e0d4ee533d38 VGCL_PM6redo competitor hdisk8 00c6e0d4ee533daa VGCL_PM6dat1 competitor hdisk9 00c6e0d4ee533e1a VGCL_PM6dat1 competitor hdisk10 00c6e0d4ee533e96 VGCL_PM6dat2 competitor hdisk11 00c6e0d4ee533f0b VGCL_PM6dat2 competitor
hdisk12 00c6e0d4ee533f8a VGCL_PM6dat2 competitor hdisk13 00c6e0d4ee533ffe VGCL_PM6dat3 competitor hdisk14 00c6e0d4ee5340a8 VGCL_PM6log competitor hdisk15 00c6e0d4ee53411b VGCL_PM6log competitor hdisk16 00c6e0d4ee53419a VGCL_PM6dat1 competitor hdisk17 00c6e0d4ee53420c VGCL_PM6dat1 competitor hdisk18 00c6e0d4ee534282 VGCL_PM6dat1 competitor hdisk19 00c6e0d4ee534306 VGCL_PM6dat2 competitor hdisk20 00c6e0d4ee534375 VGCL_PM6dat2 competitor hdisk21 00c6e0d4ee5343f2 VGCL_PM6dat3 competitor hdisk22 00c6e0d4ee534473 VGCL_PM6dat3 competitor hdisk23 00c6e0d4ee534564 VGCL_PM6log competitor hdisk24 00c6e0d4ee5345ce VGCL_PM6redo competitor
hdisk25 00c6e0d4ee534639 VGCL_PM6dat1 competitor hdisk26 00c6e0d4ee5346c0 VGCL_PM6dat1 competitor hdisk27 00c6e0d4ee534733 VGCL_PM6dat2 competitor hdisk28 00c6e0d4ee5347a9 VGCL_PM6dat2 competitor
8/17/2019 CLUSTER - AIX - Installation de HACMP_eng
http://slidepdf.com/reader/full/cluster-aix-installation-de-hacmpeng 84/93
PowerHA 5.4 installation record
Technical dossier of PowerHA 5.4 installation
CLUSTER - AIX - Installation de HACMP_eng Technical paper 848493
hdisk29 00c6e0d4ee53481e VGCL_PM6dat2 competitor hdisk30 00c6e0d4ee534894 VGCL_PM6dat3 competitor hdisk31 00c6e0d4ee534980 VGCL_PM6log competitor hdisk32 00c6e0d4ee5349f1 VGCL_PM6log competitor hdisk33 00c6e0d4ee534a5d VGCL_PM6dat1 competitor hdisk34 00c6e0d4ee534ad5 VGCL_PM6dat1 competitor hdisk35 00c6e0d4ee534b45 VGCL_PM6dat1 competitor hdisk36 00c6e0d4ee 534bd 4 VGCL_PM6dat2 competitor hdisk37 00c6e0d4ee534c4e VGCL_PM6dat2 competitor hdisk38 00c6e0d4ee534cbb VGCL_PM6dat3 competitor hdisk39 00c6e0d4ee534d2f VGCL_PM6dat3 competitor hdisk40 00c6e0c44df3c266 Nun hdisk41 00c6e0c44df3f640 VGCL_PM6log competitor hdisk42 00c6e0c44df41276 VGCL_PM6log competitor hdisk43 00c6e0c44df4299f Nun hdisk44 00c6e0d496e3dbee VGCL_PM6log competitor hdisk45 00c6e0d496e3fb07 VGCL_PM6log competitor hdisk46 00c6e0d496e41099 VGCL_PM6log competitor hdisk47 00c6e0d496e4291a VGCL_PM6log competitor
================================================================================ COMMAND: df ================================================================================ Filesystem 512-blocks Free %Used Iused %Iused Mounted one /dev/hd4 2883584 2466936 15% 12869 5%/ /dev/hd2 6029312 1463624 76% 44690 21% /usr
/dev/hd9var 2359296 1427800 40% 6137 4% /var /dev/hd3 4456448 3797136 15% 412 1% /tmp /dev/hd11admin 262144 261416 1% 5 1% /admin /proc - - - - - /proc /dev/hd10opt 262144 68440 74% 2046 21% /opt /dev/lvusers 2097152 2095976 1% 32 1% /usersconnect /dev/lvfs01 14024704 13990024 1% 384 1% /FS01 /dev/lvfs80 14024704 14009584 1% 932 1% /FS80
================================================================================ COMMAND: mount ================================================================================
node mounted mounted over vfs dates options
-------- --------------- --------------- ------ ------------ --------------- /dev/hd4/jfs October 2nd, 22 09:17 rw, log=/dev/hd8
/dev/hd2 /usr jfs October 2nd, 22 09:17 rw, log=/dev/hd8 /dev/hd9var /var jfs October 2nd, 22 09:17 rw, log=/dev/hd8
/dev/hd3 /tmp jfs October 2nd, 22 09:17 rw, log=/dev/hd8
/dev/hd11admin /admin jfs October 2nd, 22 09:17 rw, log=/dev/hd8
/proc /proc procfs Oct. 22 09:17 rw
/dev/hd10opt /opt jfs October 2nd, 22 09:17 rw, log=/dev/hd8
/dev/lvusers /usersconnect jfs October 2nd, 22 09:17 rw, log=/dev/hd8
/dev/lvfs01 /FS01 jfs October 2nd, 22 09:17 rw, log=/dev/logvgfs01
/dev/lvfs80 /FS80 jfs October 2nd, 22 09:17 rw, log=/dev/logvgfs01
================================================================================ COMMAND: exportfs
8/17/2019 CLUSTER - AIX - Installation de HACMP_eng
http://slidepdf.com/reader/full/cluster-aix-installation-de-hacmpeng 85/93
PowerHA 5.4 installation record
Technical dossier of PowerHA 5.4 installation
CLUSTER - AIX - Installation de HACMP_eng Technical paper 858593
================================================================================ exportfs: nothing exported
================================================================================ COMMAND: lsfs ================================================================================ Name Nodename Mount Pt VFS Size Options Accounting Car /dev/hd4 -- /jfs2 2883584 -- yes No /dev/hd2 -- /usr jfs2 6029312 -- yes No /dev/hd9var -- /var jfs2 2359296 -- yes No /dev/hd3 -- /tmp jfs2 4456448 -- yes No /dev/hd11admin -- /admin jfs2 262144 -- yes No /proc -- /proc procfs -- -- yes No /dev/hd10opt -- /opt jfs2 262144 -- yes No /dev/lvusers -- /usersconnect jfs2 2097152 rw yes No /dev/lvfs01 -- /FS01 jfs2 14024704 -- yes No /dev/lvfs80 -- /FS80 jfs2 14024704 -- yes No /dev/pm6lvscan -- /invscan jfs2 -- rw No No /dev/pm6lvint -- /inter jfs2 -- rw No No /dev/pm6lvdveb -- /usr/sap/PM6/DVEBMGS00/work/tri jfs2 -- rw NoNo /dev/pm6lvmirA -- /oracle/PM6/mirrlogA jfs2 -- cio, rw No No /dev/pm6lvmirB -- /oracle/PM6/mirrlogB jfs2 -- cio, rw No No /dev/pm6lvoriB -- /oracle/PM6/origlogB jfs2 -- cio, rw No No /dev/pm6lvoriA -- /oracle/PM6/origlogA jfs2 -- cio, rw No No /dev/pm6lvorastg -- /oracle/stage jfs2 -- rw No No /dev/pm6lvdata1 -- /oracle/PM6/sapdata1 jfs2 -- cio, rw No No /dev/pm6lvdata2 -- /oracle/PM6/sapdata2 jfs2 -- cio, rw No No /dev/pm6lvdata3 -- /oracle/PM6/sapdata3 jfs2 -- cio, rw No No /dev/pm6lvdata4 -- /oracle/PM6/sapdata4 jfs2 -- cio, rw No No /dev/pm6lvdata5 -- /oracle/PM6/sapdata5 jfs2 -- cio, rw No No /dev/pm6lvdata6 -- /oracle/PM6/sapdata6 jfs2 -- cio, rw No No /dev/PM6_lvora -- /oracle jfs2 -- cio, rw No No /dev/lvorapm6 -- /oracle/PM6 jfs2 -- rw No No /dev/pm6lvsapreog -- /oracle/PM6/sapreorg jfs2 -- rw No No /dev/pm6lvmnt -- /sapmnt/PM6 jfs2 -- rw No No /dev/pm6lvmntpool -- /sapmnt/PM6/global/600SPOOL jfs2 -- rw No No /dev/pm6lvusrsap -- /usr/sap jfs2 -- rw No No /dev/pm6lvusap -- /usr/sap/PM6 jfs2 -- rw No No /dev/pm6lvstrans -- /usr/sap/trans jfs2 -- rw No No
/dev/pm6lvadm -- /home/pm6adm jfs2 -- rw No No /dev/pm6lvarching -- /usr/sap/archiving jfs2 -- rw No No /dev/pm6lvcft -- /FS01/logiciel/cft jfs2 -- rw No No /dev/pm6lvdazl -- /FS01/logiciel/hpos jfs2 -- rw No No /dev/pm6lvorarch -- /oracle/PM6/oraarch jfs2 -- rw No No
================================================================================ COMMAND: COM ================================================================================ Fileset Level Action Statuses Dates Time
---------------------------------------------------------------------------- Path: /usr/lib/objrepos
cluster.adt.es.cl ient.include 5.4.0.0 MADE SUPPLEMENTS 9/6/09 10:18: 49
5.4.1.0 MADE SUPPLEMENTS 9/6/09 11:20: 15
8/17/2019 CLUSTER - AIX - Installation de HACMP_eng
http://slidepdf.com/reader/full/cluster-aix-installation-de-hacmpeng 86/93
PowerHA 5.4 installation record
Technical dossier of PowerHA 5.4 installation
CLUSTER - AIX - Installation de HACMP_eng Technical paper 868693
cluster.adt.es.cl ient.samples.clinfo
5.4.0.0 MADE SUPPLEMENTS 9/6/09 10:18: 49
5.4.1.0 MADE SUPPLEMENTS 9/6/09 11:20: 15
cluster.adt.es.cl ient.samples.clstat
5.4.0.0 MADE SUPPLEMENTS 9/6/09 10:18: 49
5.4.1.0 MADE SUPPLEMENTS 9/6/09 11:20: 15
5.4.1.2 MADE SUPPLEMENTS 9/6/09 11:20: 15
cluster.adt.es.cl ient.samples.libcl
5.4.0.0 MADE SUPPLEMENTS 9/6/09 10:18: 49 5.4.1.0 MADE SUPPLEMENTS 9/6/09 11:20: 15
cluster.adt.es.ja va.demo.monitor
5.4.0.0 MADE SUPPLEMENTS 9/6/09 10:18: 49
5.4.1.0 MADE SUPPLEMENTS 9/6/09 11:20: 15
cluster.doc.en_US.es.ht ml
5.4.0.0 MADE SUPPLEMENTS 9/6/09 10:18: 44 5.4.1.0 MADE SUPPLEMENTS 9/6/09 11:20: 15
cluster.doc.en_US.es.pd F
5.4.0.0 MADE SUPPLEMENTS 9/6/09 10:18: 44
5.4.1.0 MADE SUPPLEMENTS 9/6/09 11:20: 15
cluster.es.cl ient. lib
5.4.0.0 MADE SUPPLEMENTS 9/6/09 10:18: 40
5.4.1.0 MADE SUPPLEMENTS 9/6/09 11:20: 15
5.4.1.4 MADE SUPPLEMENTS 9/6/09 11:20: 15
cluster.es.cl ient. rte
5.4.0.0 MADE SUPPLEMENTS 9/6/09 10:18: 40 5.4.1.0 MADE SUPPLEMENTS 9/6/09 11:20: 15
5.4.1.5 MADE SUPPLEMENTS 9/6/09 11:20: 15
cluster.es.cl ient.utils
5.4.0.0 MADE SUPPLEMENTS 9/6/09 10:18: 40
5.4.1.0 MADE SUPPLEMENTS 9/6/09 11:20: 15
5.4.1.5 MADE SUPPLEMENTS 9/6/09 11:20: 15
cluster.es.cl ient. wsm 5.4.0.0 MADE SUPPLEMENTS 9/6/09 10:18: 40
5.4.1.0 MADE SUPPLEMENTS 9/6/09 11:20: 15 5.4.1.5 MADE SUPPLEMENTS 9/6/09 11:20: 15
8/17/2019 CLUSTER - AIX - Installation de HACMP_eng
http://slidepdf.com/reader/full/cluster-aix-installation-de-hacmpeng 87/93
PowerHA 5.4 installation record
Technical dossier of PowerHA 5.4 installation
CLUSTER - AIX - Installation de HACMP_eng Technical paper 878793
cluster.es.cs poc.cmds
5.4.0.0 MADE SUPPLEMENTS 9/6/09 11:04: 51
5.4.1.0 MADE SUPPLEMENTS 9/6/09 11:20: 15
5.4.1.5 MADE SUPPLEMENTS 9/6/09 11:20: 15
cluster.es.cs poc. dsh
5.4.0.0 MADE SUPPLEMENTS 9/6/09 10:18: 39
5.4.1.0 MADE SUPPLEMENTS 9/6/09 11:20: 15
cluster.es.cs poc. rte
5.4.0.0 MADE SUPPLEMENTS 9/6/09 11:04: 51 5.4.1.0 MADE SUPPLEMENTS 9/6/09 11:20: 15
5.4.1.3 MADE SUPPLEMENTS 9/6/09 11:20: 15
cluster.es.pl ugins.dhcp
5.4.0.0 MADE SUPPLEMENTS 9/6/09 11:04: 50
5.4.1.0 MADE SUPPLEMENTS 9/6/09 11:20: 15
cluster.es.pl ugins. dns 5.4.0.0 MADE SUPPLEMENTS 9/6/09 11:04: 50
5.4.1.0 MADE SUPPLEMENTS 9/6/09 11:20: 15
cluster.es.pl ugins.printserver
5.4.0.0 MADE SUPPLEMENTS 9/6/09 11:04: 50
5.4.1.0 MADE SUPPLEMENTS 9/6/09 11:20: 15
cluster.es.se rver.cfgast
5.4.0.0 MADE SUPPLEMENTS 9/6/09 11:04: 54
5.4.1.0 MADE SUPPLEMENTS 9/6/09 11:20: 15
cluster.es.se rver.diag
5.4.0.0 MADE SUPPLEMENTS 9/6/09 11:04: 54 5.4.1.0 MADE SUPPLEMENTS 9/6/09 11:20: 15
5.4.1.5 MADE SUPPLEMENTS 9/6/09 11:20: 16
cluster.es.se rver.events
5.4.0.0 MADE SUPPLEMENTS 9/6/09 11:04: 54
5.4.1.0 MADE SUPPLEMENTS 9/6/09 11:20: 15
5.4.1.5 MADE SUPPLEMENTS 9/6/09 11:20: 16
cluster.es.se rver. rte 5.4.0.0 MADE SUPPLEMENTS 9/6/09 11:04: 54
5.4.1.0 MADE SUPPLEMENTS 9/6/09 11:20: 15 5.4.1.5 MADE SUPPLEMENTS 9/6/09 11:20: 16
8/17/2019 CLUSTER - AIX - Installation de HACMP_eng
http://slidepdf.com/reader/full/cluster-aix-installation-de-hacmpeng 88/93
PowerHA 5.4 installation record
Technical dossier of PowerHA 5.4 installation
CLUSTER - AIX - Installation de HACMP_eng Technical paper 888893
cluster.es.se rver.testtool
5.4.0.0 MADE SUPPLEMENTS 9/6/09 11:04: 54
5.4.1.0 MADE SUPPLEMENTS 9/6/09 11:20: 15
5.4.1.1 MADE SUPPLEMENTS 9/6/09 11:20: 15
cluster.es.se rver.utils
5.4.0.0 MADE SUPPLEMENTS 9/6/09 11:04: 54
5.4.1.0 MADE SUPPLEMENTS 9/6/09 11:20: 16
5.4.1.5 MADE SUPPLEMENTS 9/6/09 11:20: 16
cluster.es.wo rksheets 5.4.0.0 MADE SUPPLEMENTS 9/6/09 10:18: 38
5.4.1.0 MADE SUPPLEMENTS 9/6/09 11:20: 15
5.4.1.3 MADE SUPPLEMENTS 9/6/09 11:20: 15
cluster.license
5.4.0.0 MADE SUPPLEMENTS 9/6/09 10:18: 37
5.4.1.0 MADE SUPPLEMENTS 9/6/09 11:20: 15
5.4.1.1 MADE SUPPLEMENTS 9/6/09 11:20: 15
Path: /etc/objrepos
cluster.es.cl ient. lib 5.4.0.0 MADE SUPPLEMENTS 9/6/09 10:18: 43
5.4.1.0 MADE SUPPLEMENTS 9/6/09 11:20: 15
5.4.1.4 MADE SUPPLEMENTS 9/6/09 11:20: 15
cluster.es.cl ient. rte
5.4.0.0 MADE SUPPLEMENTS 9/6/09 10:18: 43
5.4.1.0 MADE SUPPLEMENTS 9/6/09 11:20: 15 5.4.1.5 MADE SUPPLEMENTS 9/6/09 11:20: 15
cluster.es.cs poc. rte 5.4.0.0 MADE SUPPLEMENTS 9/6/09 11:04: 53
cluster.es.se rver.diag
5.4.0.0 MADE SUPPLEMENTS 9/6/09 11:05: 02
cluster.es.se rver.events
5.4.0.0 MADE SUPPLEMENTS 9/6/09 11:05: 02
cluster.es.se rver. rte
5.4.0.0 MADE SUPPLEMENTS 9/6/09 11:05: 02
5.4.1.0 MADE SUPPLEMENTS 9/6/09 11:20: 15 5.4.1.5 MADE SUPPLEMENTS 9/6/09 11:20: 16
8/17/2019 CLUSTER - AIX - Installation de HACMP_eng
http://slidepdf.com/reader/full/cluster-aix-installation-de-hacmpeng 89/93
PowerHA 5.4 installation record
Technical dossier of PowerHA 5.4 installation
CLUSTER - AIX - Installation de HACMP_eng Technical paper 898993
cluster.es.se rver.utils
5.4.0.0 MADE SUPPLEMENTS 9/6/09 11:05: 02
5.4.1.5 MADE SUPPLEMENTS 9/6/09 11:20: 16
Path: /usr/share/lib/objrepos cluster.man.en_US.es.da your
5.4.0.0 MADE SUPPLEMENTS 9/6/09 11:13: 31
5.4.1.0 MADE SUPPLEMENTS 9/6/09 11:20: 15 5.4.1.3 MADE SUPPLEMENTS 9/6/09 11:20: 15
================================================================================ COMMAND: ifconfig en0 ================================================================================ en0: flags=1e080863,480<UP, BROADCAST, NOTRAILERS, RUNNING, SIMPLEX, multicast,GROUPRT, 64BIT, CHECKSUM_OFFLOAD (ACTIVATES), CHAIN>
inet 7.27.224.63 netmask 0xffffff00 broadcast 7.27.224.255
inet 192.168.40.192 netmask 0xffffff00 broadcast 192.168.40.255
tcp_sendspace 262144 tcp_recvspace 262144 rfc1323 1
================================================================================ COMMAND: ifconfig lo0 ================================================================================ lo0: flags=e08084b<UP, BROADCAST, LOOPBACK, RUNNING, SIMPLEX, multicast,GROUPRT, 64BIT>
inet 127.0.0.1 netmask 0xff000000 broadcast 127.255.255.255 inet6:: 1/0
tcp_sendspace 131072 tcp_recvspace 131072 rfc1323 1
================================================================================ COMMAND: lsvg - L FS01vg ================================================================================ FS01vg: STANDARD LV NAME LPs PPs special minutes LV STATE MOUNT NOT open logvgfs01 jfs2log 1 1 1/syncd N/A lvfs01 jfs2 214 214 1 open/syncd /FS01 lvfs80 jfs2 214 214 1 open/syncd /FS80
================================================================================ COMMAND: lsvg - L rootvg ================================================================================ rootvg: STANDARD LV NAME LPs PPs special minutes LV STATE MOUNT NOT hd5 bootup 1 1 1 closed/syncd N/A hd6 paging 235 235 1 open/syncd N/A open hd8 jfs2log 1 1 1/syncd N/A hd4 jfs2 11 11 1 open/syncd/ hd2 jfs2 23 23 1 open/syncd /usr hd9var jfs2 9 9 1 open/syncd /var hd3 jfs2 17 17 1 open/syncd /tmp open hd10opt jfs2 1 1 1/syncd /opt open hd11admin jfs2 1 1 1/syncd /admin lg_dumplv sysdump 32 32 1 open/syncd N/A
8/17/2019 CLUSTER - AIX - Installation de HACMP_eng
http://slidepdf.com/reader/full/cluster-aix-installation-de-hacmpeng 90/93
PowerHA 5.4 installation record
Technical dossier of PowerHA 5.4 installation
CLUSTER - AIX - Installation de HACMP_eng Technical paper 909093
lvusers jfs2 8 8 1 open/syncd /usersconnect
================================================================================ COMMAND: lslv - L logvgfs01 ================================================================================ logvgfs01: N/A STATEMENT COPIES IN BAND DISTRIBUTION hdisk5 001:000: 000 100% 000:001: 000:000: 000
================================================================================ COMMAND: lslv - L lvfs01 ================================================================================ lvfs01: /FS01
STATEMENT COPIES IN BAND DISTRIBUTION hdisk5 214:000: 000 47% 064:101: 049:000: 000
================================================================================ COMMAND: lslv - L lvfs80 ================================================================================ lvfs80: /FS80 STATEMENT COPIES IN BAND DISTRIBUTION hdisk5 214:000: 000 0% 039:000: 053:102: 020
================================================================================ COMMAND: lslv - L hd5
================================================================================ hd5: N/A STATEMENT COPIES IN BAND DISTRIBUTION hdisk0 001:000: 000 100% 001:000: 000:000: 000
================================================================================ COMMAND: lslv - L hd6 ================================================================================ hd6: N/A STATEMENT COPIES IN BAND DISTRIBUTION hdisk0 235:000: 000 26% 102:062: 062:009: 000
================================================================================ COMMAND: lslv - L hd8 ================================================================================ hd8: N/A
STATEMENT COPIES IN BAND DISTRIBUTION hdisk0 001:000: 000 100% 000:000: 001:000: 000
================================================================================ COMMAND: lslv - L hd4 ================================================================================ hd4: / STATEMENT COPIES IN BAND DISTRIBUTION hdisk0 011:000: 000 36% 000:000: 004:007: 000
================================================================================ COMMAND: lslv - L hd2
8/17/2019 CLUSTER - AIX - Installation de HACMP_eng
http://slidepdf.com/reader/full/cluster-aix-installation-de-hacmpeng 91/93
PowerHA 5.4 installation record
Technical dossier of PowerHA 5.4 installation
CLUSTER - AIX - Installation de HACMP_eng Technical paper 919193
================================================================================ hd2: /usr STATEMENT COPIES IN BAND DISTRIBUTION hdisk0 023:000: 000 100% 000:000: 023:000: 000
================================================================================ COMMAND: lslv - L hd9var ================================================================================ hd9var: /var STATEMENT COPIES IN BAND DISTRIBUTION hdisk0 009:000: 000 100% 000:000: 009:000: 000
================================================================================
COMMAND: lslv - L hd3 ================================================================================ hd3: /tmp STATEMENT COPIES IN BAND DISTRIBUTION hdisk0 017:000: 000 5% 000:000: 001:016: 000
================================================================================ COMMAND: lslv - L hd10opt ================================================================================ hd10opt: /opt STATEMENT COPIES IN BAND DISTRIBUTION hdisk0 001:000: 000 100% 000:000: 001:000: 000
================================================================================ COMMAND: lslv - L hd11admin ================================================================================ hd11admin: /admin STATEMENT COPIES IN BAND DISTRIBUTION hdisk0 001:000: 000 100% 000:000: 001:000: 000
================================================================================ COMMAND: lslv - L lg_dumplv ================================================================================ lg_dumplv: N/A STATEMENT COPIES IN BAND DISTRIBUTION hdisk0 032:000: 000 100% 000:032: 000:000: 000
================================================================================ COMMAND: lslv - L lvusers ================================================================================ lvusers: /usersconnect STATEMENT COPIES IN BAND DISTRIBUTION hdisk0 008:000: 000 100% 000:008: 000:000: 000
================================================================================ COMMAND: odmget HACMPdaemons ================================================================================
HACMPdaemons: nodename = “gtyxsappm6p2”
8/17/2019 CLUSTER - AIX - Installation de HACMP_eng
http://slidepdf.com/reader/full/cluster-aix-installation-de-hacmpeng 92/93
PowerHA 5.4 installation record
Technical dossier of PowerHA 5.4 installation
CLUSTER - AIX - Installation de HACMP_eng Technical paper 929293
daemon = “clstrmgr”
type = “start”
object = “manages”
been worth = “car”
HACMPdaemons:
nodename = “gtyxsappm6p2”
daemon = “clstrmgr” type = “start”
object = “broadcast”
been worth = “true”
HACMPdaemons: nodename = “gtyxsappm6p2”
daemon = “clinfo”
type = “start”
object = “time”
been worth = “true”
HACMPdaemons: nodename = “gtyxsappm6p2”
daemon = “clstrmgrES”
type = “stop” object = “time”
been worth = “now”
HACMPdaemons: nodename = “gtyxsappm6p2”
daemon = “clstrmgrES”
type = “stop”
object = “broadcast”
been worth = “true”
HACMPdaemons: nodename = “gtyxsappm6p2”
daemon = “clstrmgrES”
type = “stop”
object = “mode”
been worth = “graceful”
================================================================================ COMMAND: odmget HACMPsp2 ================================================================================
8/17/2019 CLUSTER - AIX - Installation de HACMP_eng
http://slidepdf.com/reader/full/cluster-aix-installation-de-hacmpeng 93/93
PowerHA 5.4 installation record
Technical dossier of PowerHA 5.4 installation
END OF DOCUMENT
Recommended