View
218
Download
3
Category
Tags:
Preview:
Citation preview
Climate change and Urban Vulnerability in Africa
Assessing vulnerability of urban systems, population and goods in relation to natural and
man-made disasters in Africa
1
“Training on the job” Course on Hazards, Risk and (Bayesian) multi-risk assessement
Napoli, 24.10.2011 – 11.11.2011
10/04/23 Fatemeh Jalayer
10/04/23 Fatemeh Jalayer Slide 2
Earth Structure
Crust: The uppermost 5-70 km of the earth. There are two types of crust: continental and oceanic. Continental crust ranges from 10-70 km thick and has a composition approximating that of granite. Oceanic crust, on the other hand, is approximately 5 km thick and has a composition similar to basalt, making it significantly denser than continental crust.
Mantle: The middle portion of the interior of the earth, starting below the crust at 5-70 km below the earth’s surface and continuing to a depth of 2900 km.
Core The innermost layer of the earth, which starts at ~2900 km depth. The core is composed mainly of iron and consists of a molten outer core and a solid inner core.
10/04/23 Fatemeh Jalayer Slide 3
Plate Tectonics
Subduction zones Mid-Ocean ridges
10/04/23 Fatemeh Jalayer Slide 4
Map showing earthquakes from 2003-2011 with magnitude greater than 3. Colors indicate depth of hypocenter, or origin of the earthquake: red is 0-33 km, yellow is 33-100 km, green is 100-400 km, and blue is >400 km depth. Data are from the Advanced National Seismic System.
Plate Tectonics
10/04/23 Fatemeh Jalayer Slide 5
Map showing volcanoes that have been active in the last 10,000 years. Colored triangles indicate different volcano types: red triangles are primarily calderas, green triangles are stratovolcanoes, blue triangles are shield volcanoes and fissure vents. Data are from the Smithsonian Institution, Global Volcanism Program.
Plate Tectonics
10/04/23 Fatemeh Jalayer Slide 6
Cross-section of the Mid-Atlantic Ridge near latitude 14° S. Blue triangle represents the location of fissure volcanoes. Colored circles represent earthquakes, color-coded by depth
Divergent boundaries
Transform boundaries
Cross-section of the San Andreas Fault in California near latitude 36° N. Colored circles represent earthquakes, color-coded by depth
Plate Tectonics
10/04/23 Fatemeh Jalayer Slide 7
Cross-section of the South American subduction zone near latitude 22° S. Green triangles represent the locations of stratovolcanoes. Colored circles represent earthquakes, color-coded by depth
Cross-section of the Tonga trench near latitude 21° S. Colored triangles represent the location of volcanoes, color-coded by type of volcano. Colored circles represent earthquakes, color-coded by depth.
Oceanic meets continental Oceanic meets more oceanic
Convergent boundaries
Continental meets more continental Cross-section of the Himalayas along 88° E longitude. Colored circles represent earthquakes, color-coded by depth
Plate Tectonics
10/04/23 Fatemeh Jalayer Slide 8
Ipocenter and Epicenter
10/04/23 Fatemeh Jalayer Slide 9
Distance Typology
FaultRupture
Ipocenter
Epicenter Site
Epicentral distance
Closet distance to the rupture surfaceSlant Distance
Seismogenic Depth
Closet distance to the seismogenic part of the rupture surface
Ipocentral distance
Joyner-Boore Distance
10/04/23 Fatemeh Jalayer Slide 10
Fault typologies
10/04/23 Fatemeh Jalayer Slide 11
Fault typologies
10/04/23 Fatemeh Jalayer Slide 12
Fault typologies
Strike-slip fault Normal fault
Reverse fault Normal-oblique fault
10/04/23 Fatemeh Jalayer Slide 13
Waves propagation
p wave s wave
Rayleigh wave
Love wave
Body waves Surface waves
10/04/23 Fatemeh Jalayer Slide 14
Waves propagation
10/04/23 Fatemeh Jalayer Slide 15
Site response
surface waves
reflected waves
In alluvial basins on stiff bedrock, wave interpherences occur due to:- multiple reflections, - diffractions, - body to surface mode conversions.
These phenomena induce, overall:- higher peak amplification- significant increase of duration with respect to 1D conditions.
10/04/23 Fatemeh Jalayer Slide 16
Earthquake intensityMercalli intensity scale
The scale quantifies the effects of an earthquake on the Earth's surface, humans, objects of nature, and man-made structures on a scale from I (not felt) to XII (total destruction). Values depend upon the distance to the earthquake, with the highest intensities being around the epicentral area. Data gathered from people who have experienced the quake are used to determine an intensity value for their location. The Mercalli (Intensity) scale originated with the widely-used simple ten-degree Rossi-Forel scale, which was revised by Italian vulcanologist Giuseppe Mercalli in 1884 and 1906.
10/04/23 Fatemeh Jalayer Slide 17
Earthquake intensityMercalli intensity scaleDamage map – Irpinia Earthquake, 1980
10/04/23 Fatemeh Jalayer Slide 18
Earthquake intensityRichter magnitude
His inspiration was the apparent magnitude scale used in astronomy to describe the brightness of stars and other celestial objects. Richter arbitrarily chose a magnitude 0 event to be an earthquake that would show a maximum combined horizontal displacement of 1 µm (0.00004 in) on a seismogram recorded using a Wood-Anderson torsion seismograph 100 km (62 mi) from the earthquake epicenter. This choice was intended to prevent negative magnitudes from being assigned. The smallest earthquakes that could be recorded and located at the time were of magnitude 3, approximately. However, the Richter scale has no lower limit, and sensitive modern seismographs now routinely record quakes with negative magnitudes.
10/04/23 Fatemeh Jalayer Slide 19
Earthquake intensityMoment magnitude
Fault momentFault momentM0 = ∙ A ∙ D
Rigidity G [F/L2] Average offset ≈ Slip [L]
Fault area [L2]
M0 [dyne cm]
Kanamori 1977
Moment MagnitudeMoment Magnitude
10/04/23 Fatemeh Jalayer Slide 20
Magnitude relationship
In seismology, the Gutenberg–Richter law (GR law) expresses the relationship between the magnitude and total number of earthquakes in any given region and time period of at least that magnitude
or
Where N is the number of events having a magnitude > M; a and b are constants calibrated on a given set of events.
10/04/23 Fatemeh Jalayer Slide 21
Magnitude relationship
The constant b is typically equal to 1.0 in seismically active regions. This means that for every magnitude 4.0 event there will be 10 magnitude 3.0 quakes and 100 magnitude 2.0 quakes. There is some variation with b-values in the range 0.5 to 1.5 depending on the tectonic environment of the region. A notable exception is during earthquake swarms when the b-value can become as high as 2.5 indicating an even larger proportion of small quakes to large ones. A b-value significantly different from 1.0 may suggest a problem with the data set; e.g. it is incomplete or contains errors in calculating magnitude
The a-value is of less scientific interest and simply indicates the total seismicity rate of the region.
10/04/23 Fatemeh Jalayer Slide 22
Ground Motion prediction relations
State-of-the-art estimates of expected ground motion at a given distance from an earthquake of a given magnitude are the second element of earthquake hazard assessments. These estimates are usually equations, called attenuation relationships, which express ground motion as a function of magnitude and distance (and occasionally other variables, such as type of faulting). Commonly assessed ground motions are maximum intensity, peak ground acceleration (PGA), peak ground velocity (PGV), and several spectral accelerations (SA). Each ground motion mapped corresponds to a portion of the bandwidth of energy radiated from an earthquake. PGA and 0.2s SA correspond to short-period energy that will have the greatest effect on short-period structures (one-to two story). PGA values are directly related to the lateral forces that damage short period. Longer-period SA (1.0s, 2.0s, etc.) depict the level of shaking that will have the greatest effect on longer-period structures (10+ story buildings, bridges, etc.). Ground motion attenuation relationships may be determined in two different ways: empirically, using previously recorded ground motions, or theoretically, using seismological models to generate synthetic ground motions which account for the source, site, and path effects. There is overlap in these approaches, however, since empirical approaches fit the data to a functional form suggested by theory and theoretical approaches often use empirical data to determine some parameters.
10/04/23 Fatemeh Jalayer Slide 23
The ground motion at a site, for example Peak Ground Acceleration depends on the earthquake source, the seismic wave propagation and the site response. Earthquake source signifies the earthquake magnitude, the depth and the focal mechanism, the propagation depends mainly on the distance to the site. The site response deals with the local geology (site classification); it is the subject of microzonation.
Ground Motion prediction relations
The basic functional (logarithmic) form for ground motion attenuation relationship is defined as (Reiter 1990)
ln Y = ln b1 + ln f1(M) + ln f2(R) + ln f3(M,R) + ln f4(P) + ln
Where: Y is the strong motion parameter to be estimated (dependant variable), it is lognormal distributed; f1(M) is a function of the independent variable M, earthquake source size generally magnitude; f2(R) depends on the variable R, the seismogenic area source to site distance; f3(M,R) is a possible joint function between M and R (for example for an earthquake with big magnitude the seismogenic area is large and the source to site distance may be different); f4(P) are functions representing possible source and site effects (for example different style of faulting in the near field may generate different ground motions values Abrahamson and Shedlock (1997)); is an error term representing the uncertainty in Y
10/04/23 Fatemeh Jalayer Slide 24
Ground Motion prediction relations
Sabetta e Pugliese (attenuation law for Italy)
10/04/23 Fatemeh Jalayer Slide 25
Seismic zoning
Punctual sourcePunctual source: this typology of modeling it’s used for fault very deep or very : this typology of modeling it’s used for fault very deep or very far from the interest area. far from the interest area.
Linear sourceLinear source: this typology of modeling it’s used with hypothesis that all the : this typology of modeling it’s used with hypothesis that all the point of the line can be fracture point with the same probability. point of the line can be fracture point with the same probability.
Planar sourcePlanar source: this typology of modeling it’s used with hypothesis that all the : this typology of modeling it’s used with hypothesis that all the point of the line can be fracture point with the same probability. point of the line can be fracture point with the same probability.
10/04/23 Fatemeh Jalayer Slide 26
PSHAProbabilistic Seismic Hazard Analisis
For each Seismic zones target is to evaluate the annual exceedance frequency of a given intensity trough the follow integral:
10/04/23 Fatemeh Jalayer Slide 27
PSHAProbabilistic Seismic Hazard Analisis
Starting from the knowledge of Seismic Zone Typology, of Attenuation Law and G-R Law is possible to evaluate:
Extension to more Seismic Zones
10/04/23 Fatemeh Jalayer Slide 28
PSHAProbabilistic Seismic Hazard Analisis
To convert the annual rate of events to a probability, we consider the probability that the ground motion exceeds test level x at least once during a specific time interval. A standard assumption is that the occurrence of earthquake is a POISSONIAN process.
For t=1 this probability is the annual hazard. Starting from previous relation is possible to obtain the Return Period of the generic event that has an exceedance probability of P in time t:
10/04/23 Fatemeh Jalayer Slide 29
Deaggregation of Hazard
The hazard curve gives the combined effect of all magnitudes and distances on the probability of exceeding a given ground motion level. Since all of the sources, magnitudes, and distances are mixed together, it is difficult to get an intuitive understanding of what is controlling the hazard from the hazard curve by itself. A common practice is to break the hazard back down into its contributions from different magnitude and distance pairs to provide insight into what events are the most important for the hazard.
10/04/23 Fatemeh Jalayer Slide 30
Example
The example site considered has two faults. Fault A, produces earthquakes with magnitude M=6 and distance R=10km from the site; and has an annual occurrence rate of =0.01; we denote this earthquake Event A. Fault B produces earthquakes with magnitude M=8 and distance R=25km from the site, and has annual occurrence of =0.002; we denote this earthquake Event B. Both events have strike slip mechanism.
Site and Event description
10/04/23 Fatemeh Jalayer Slide 31
Example
PSHA Computation
10/04/23 Fatemeh Jalayer Slide 32
Example
In this simplified site, each event (Eventj) corresponds to a single magnitude (mj) and distance (rj). The conditional probability that each event causes Sa>y is given by follow equation:
Deaggregation of Events
10/04/23 Fatemeh Jalayer Slide 33
Example
Deaggregation of Magnitude
The deaggregation mean magnitude associated with a specific GMPM can be found using equation:
Bold line
10/04/23 Fatemeh Jalayer Slide 34
Example
Deaggregation of Distance
Recommended