View
227
Download
0
Category
Preview:
Citation preview
8/6/2019 CFAI Handbook 10a
1/27
Cessna FITS Accepted InstructorG1000 Training Program Handbook
January 2010 Rev. I
8/6/2019 CFAI Handbook 10a
2/27
CESSNA FITS ACCEPTED INSTRUCTOR (CFAI) DESIGNATION OVERVIEW
The Cessna FITS Accepted Instructor (CFAI) designation allows a designated certifiedflight instructor to provide Cessna FITS accepted G1000 transition training to Cessnacustomers and Cessna rental pilots worldwide. The instructor must remain affiliatedwith a Cessna Pilot Center (CPC) or Cessna Sales Team Authorized Representative(CSTAR). If the CFAI conducts G1000 Transition Training in conjunction with the saleof an aircraft, the CPC or CSTAR is then given the monetary training entitlementprovided for each aircraft. Factory trained CFAIs are not allowed to train CFAIs in thefield.
The CFAI designation is not required to instruct in G1000-equipped aircraft for aircraftowners or rental pilots. It is only required to teach the Cessna FITS Accepted Course,provide FITS completion certificates, and to train Cessna customers for factoryreimbursement.
To obtain this designation, the CFAI must do the following:1. Complete the G1000 Transition Training Course and CFAI Course. This includes
both the required ground and flight training. The CFAI must obtain the highestdesired learning outcome level for each task and demonstrate proficiency andknowledge on each task.
2. Return the FAA Industry Training Standard (FITS) Scenario Based TransitionSyllabus and Standards for the Cessna Single Engine Propeller Aircraft completewith sample scenarios for the area in which the majority of training will take placeto the designated representative of the Pilot Training Department.
To retain this designation, the CFAI must do the following:3. Maintain the CFAI Proficiency Program Subscription. This fee is due in January
of each year and is good for 12 calendar months. The CFAI will be notified of thefee structure and subscription format options for the following year in January.
4. Notify the Pilot Training Department immediately regarding changes inemployment status or personal information.
The CFAI designation can be upgraded to a CFAI+ (plus) status. This indicates that theCFAI may teach the Nav III G1000 Transition course as well as the FITS acceptedCorvalis Transition course, both at the Independence Factory. The Plus designationrequires factory training on these aircraft as well as materials specific to that course.CFAIs without the Plus designation may not teach this course for the certificate orreimbursement unless Cessna Pilot Training indicates they are a CFAI+.
January 2010 Rev. I Cessna Aircraft Company
8/6/2019 CFAI Handbook 10a
3/27
CESSNA NAV III TRANSITION COURSE OVERVIEW
The ground-training segment is conducted with the assistance of the Cessna FITSAccepted Training Program and the Garmin G1000 PC-Based Trainer. Time spentduring an instructor-led PIM review and cockpit familiarization session may also counttowards total ground training required. The flight training segment is completed with theguidance of the FAA Industry Training Standard (FITS) Scenario Based TransitionSyllabus and Standards for the Cessna Single Engine Propeller Aircraft and the scriptedscenarios developed by the CFAI and accepted by the Cessna Pilot TrainingDepartment in Independence.
The purposed of this training program is to familiarize the Pilot in Training (PT) with thefunctionality of the G1000 and aircraft systems. This program is not intended to beinstruction for general aircraft operation or substitute for any obligation by the operatorto be competent and knowledgeable in the operation of the aircraft or any installedcomponents.
The goals of the FITS Training Philosophy in priority of importance are as follows:1. Higher Order Thinking
a. Aeronautical Decision Making and Situational Awarenessb. Pattern Recognition (Emergency Procedures) and Decision Making
2. Automation Competence
3. Planning and Execution4. Procedural Knowledge5. Psychomotor skills
January 2010 Rev. I Cessna Aircraft Company
8/6/2019 CFAI Handbook 10a
4/27
COMPLETION REQUIREMENTS
***Please reference Programmed Training Hours for the number of hours required forthe completion of ground and flight training
Discretion of the CFAI is required during ground training to determine that the PT is atan appropriate knowledge level after completion of the appropriate ground module. ThePT should demonstrate the ability to explain the fundamental concepts and procedurescovered in the previous ground module.
The objective of scenario-based flight training is to initiate a change in the thought
processes, habits and behaviors of the students during the planning and execution ofeach scenario. The flight-training segment of the Cessna NAV III Transition TrainingProgram is completed once the PT has achieved an appropriate level of proficiency foreach task on each scenario.
REQUIRED DOCUMENTATION FOR FITS CERTIFICATE
Once training is completed, the CFAI must submit the following paperwork: Learner-Centered Grading Syllabus with signatures of both the CFAI and the
Pilot in Training (PT). Completed Customer Information and Record of Training form with contact
information for the PT. IF YOU ARE REQUESTING REIMBURSEMENTAVAILABLE WITH THE SALE OF THE AIRCRAFT, PLEASE INCLUDE THESERIAL NUMBER IN THE UPPER LEFT HAND CORNER AND SPECIFY,REIMBURSEMENT REQUESTED.
Optional: Training survey with applicable comments and suggestions from bothparties.
January 2010 Rev. I Cessna Aircraft Company
8/6/2019 CFAI Handbook 10a
5/27
LEARNER-CENTERED GRADING FORM
Desired Pilot in Training (PT) Scenario Outcomes
Maneuver Grades (Tasks)
o Explain - at the completion of the scenario the PT will be able to describe thescenario activity and understand the underlying concepts, principles, andprocedures that comprise the activity. Significant instructor effort will berequired to successfully execute the maneuver.
o Practice- at the completion of the scenario the PT will be able to plan andexecute the scenario activity. Coaching and / or assistance from the CFI willcorrect minor deviations and errors identified by the CFI.
o Perform - at the completion of the scenario, the PT will be able to perform theactivity without assistance from the CFI. Errors and deviations will be identifiedand corrected by the PT in an expeditious manner. At no time will thesuccessful completion of the activity be in doubt. Performwill be used to
signify that the PT is satisfactorily demonstrating proficiency in traditionalpiloting and systems operation skills.
Single Pilot Resource Management (SRM) Gradeso Explain the PT can verbally identify, describe, and understand the risks
inherent in the flight scenario. The student will need to be prompted to identifyrisks and make more decisions.
o Practice the PT is able to identify, understand, and apply SRM principles tothe actual flight situation. Coaching, instruction, and / or assistance from theCFI will quickly correct minor deviations and errors identified by the CFI. Thestudent will be an active decision maker.
o Manage / Decide the PT can correctly gather the most important data
available both within and outside the cockpit, identify possible course of action,evaluate the risk inherent in each course of action, and make the appropriatedecision. Instructor intervention is not required for the safe completion of theflight.
PT Name_______________________________________
Ratings Held
Private
Instrument
Commercial
ATP
January 2010 Rev. I Cessna Aircraft Company
8/6/2019 CFAI Handbook 10a
6/27
Flight Scenario 1Maneuver Grades PT Instructor
Explain Practice Perform Explain Practice Perform
Normal Preflight & Cockpit Procedures
Checklist UsageEngine Start & Taxi Procedures
Engine Start
G1000 Setup Taxi
Before Takeoff Checklist
Normal & Abnormal Indications G1000 Setup
Autopilot ChecksTakeoff
Normal/Crosswind
PFD Crosscheck Straight & Level Flight Normal Turns
Climb & DescentFlight Maneuvers
Steep Turns
Slow Flight
StallsG1000 Programming
COM/NAV Frequency Loading
Flight PlansFlight Director Operation
Vertical Modes
Lateral ModesAutopilot Operation
Vertical Modeso PITo VSo ALTo VNV
Lateral Modeso
ROLo HDGo NAV
Situational Awareness Aids
SafeTaxi TIS/TAS
Stormscope
Weather Datalink
January 2010 Rev. I Cessna Aircraft Company 6
8/6/2019 CFAI Handbook 10a
7/27
Terrain Awareness/TAWSLanding
Before Landing Checklist Normal/Crosswind
Aircraft Shutdown & Securing
Shutdown Checklist
Single Pilot Resource Management Grades PT InstructorExplain Practice Explain Practice
Scenario Planning
Flight Planning
Manage/Decide
Manage/Decide
Weight & Balance
Determining PerformanceClimb Procedures
Autopilot Climb
Checklist Usage Division of Attention
Cruise Procedures
Autopilot Cruise
Checklist Usage
Lean Assist Division of Attention
Descent Planning & Execution
VNAV Programming Autopilot Descent CFIT Avoidance
Checklist Usage
Notes:_______________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
Date__________________________________
Flight Time/Briefing Time_________/_________
CFI___________________________________
PT____________________________________
January 2010 Rev. I Cessna Aircraft Company 7
8/6/2019 CFAI Handbook 10a
8/27
Flight Scenario 2Maneuver Grades PT Instructor
Explain Practice Perform Explain Practice Perform
Normal Preflight & Cockpit Procedures
Checklist Usageo Oxygen System Checks
Engine Start & Taxi Procedures
Engine Start G1000 Setup Taxi
Before Takeoff Checklist Normal & Abnormal Indications G1000 Setup
Autopilot ChecksTakeoff
Normal/CrosswindPFD Crosscheck
Straight & Level Flight Normal Turns
Climb & DescentG1000 Programming
COM/NAV Frequency Loading Flight Plans Instrument Procedure Loading
Flight Director Operation
Vertical Modes Lateral Modes
Autopilot Operation
Vertical Modeso PITo VSo ALTo VNV
Lateral Modeso ROLo HDGo NAVo APRo REV
Instrument Approach Procedures (if applicable) ILS
VOR GPS / RNAV
DME Arcs Holding/Procedure Turns Missed Approach
January 2010 Rev. I Cessna Aircraft Compan 8
8/6/2019 CFAI Handbook 10a
9/27
Maneuver Grades (continued) PT InstructorExplain Practice Perform Explain Practice Perform
Situational Awareness Aids
SafeTaxi
TIS/TAS
Stormscope
Weather Datalink Terrain Awareness/TAWS
Landing Before Landing Checklist Normal/Crosswind
Aircraft Shutdown & Securing
Shutdown Checklist
Single Pilot Resource Management Grades PT InstructorExplain Practice Explain Practice
Scenario Planning
Flight Planning
Manage/Decide
Mana/Decid
Weight & Balance Determining Performance
Climb Procedures
Autopilot Climb Checklist Usage Division of Attention Oxygen Usage (if applicable)
Cruise Procedures
Autopilot Cruise Checklist Usage
Lean Assist Division of Attention Oxygen Usage (if applicable)
Descent Planning & Execution
VNAV Programming Autopilot Descent
CFIT Avoidance
Checklist Usage
Notes:_______________________________________________________________________________________________________________________________________________________
______________________________________________________________________________
Date__________________________________
Flight Time/Briefing Time_________/_________
CFI___________________________________
PT____________________________________
January 2010 Rev. I Cessna Aircraft Company 9
8/6/2019 CFAI Handbook 10a
10/27
Flight Scenario 3Maneuver Grades PT Instructor
Explain Practice Perform Explain Practice Perform
Normal Preflight & Cockpit Procedures
Checklist UsageEngine Start & Taxi Procedures
Engine Start G1000 Setup
TaxiBefore Takeoff Checklist
Normal & Abnormal Indications
G1000 Setup
Autopilot ChecksTakeoff
Normal/Crosswind
PFD Crosscheck Straight & Level Flight
Normal Turns
Climb & DescentG1000 Programming
COM/NAV Frequency Loading
Flight Plans Instrument Procedure Loading
Flight Director Operation
Vertical Modes Lateral Modes
Autopilot Operation Vertical Modes
o PITo VSo ALTo VNV
Lateral Modeso ROLo HDGo NAVo APRo REV
Instrument Approach Procedures with Failures (if applicable) ILS VOR
GPS/RNAV
DME Arcs Holding/Procedure Turns
Missed Approach
January 2010 Rev. I Cessna Aircraft Company 10
8/6/2019 CFAI Handbook 10a
11/27
Maneuver Grades (continued) PT InstructorExplain Practice Perform Explain Practice Perform
Situational Awareness Aids
TIS/TAS
Stormscope
Weather Datalink
Terrain Awareness/TAWSLanding
Before Landing Checklist
Landing with FailuresAircraft Shutdown & Securing
Shutdown ChecklistSingle Pilot Resource Management Grades PT Instructor
Explain Practice Explain Practice
Scenario Planning
Flight Planning
Manage/Decide
Manage/Decide
Weight & Balance
Determining Performance Diversion
Climb Procedures
Autopilot Climb Checklist Usage
Division of AttentionCruise Procedures
Autopilot Cruise
Checklist Usage
Lean Assist Division of Attention
Emergency Procedures
Display Failure AHRS/ADC Failure
Flying on Standby Instruments
Checklist UsageDescent Planning & Execution
VNAV Programming
Autopilot Descent CFIT Avoidance
Checklist Usage
Notes:_________________________________________________________________________
Date__________________________________Flight Time/Briefing Time_________/_________CFI___________________________________PT____________________________________
January 2010 Rev. I Cessna Aircraft Company 11
8/6/2019 CFAI Handbook 10a
12/27
January 2010 Rev. I Cessna Aircraft Company 12
8/6/2019 CFAI Handbook 10a
13/27
January 2010 Rev. I Cessna Aircraft Company 13
8/6/2019 CFAI Handbook 10a
14/27
PROGRAMMED TRAINING HOURS
Required Ground Training Time, All Modules ................................................. 8 hours(This time includes, but is not limited to, time spent during an interactive ground sessionwith the CFAI and the Training Program while utilizing the G1000 PC-trainer, cockpitfamiliarization exercises and the Pilot Information Manual/Pilots Operating Handbookreview/briefing.)
Required Flight Training TimeMINIMUM Total Flight Time (non-IFR rated)..................................................... 3 hours
MINIMUM Total Flight Time (IFR rated)............................................................. 4 hoursTYPICAL Total Flight Time ............................................................................. 4-6 hours
All three scenarios shall not be completed in one flight. The completion time of all tasksoutlined in the syllabus should be 3-6 hours depending on the experience of the PT. Ifadditional training is required or desired, the cost is at the discretion of the CFAI.Cessna will not reimburse the CFAI for additional training.
o If the pilot is not instrument rated, flight scenarios 1 and 3 must becompleted. Flight scenario 2 may be completed as an additional VFRflight, at the discretion of the CFAI, but is not required.
o If the aircraft is turbo-charged, high-altitude operations training can beconducted during the flight training at the discretion of the CFAI andcustomer.
Briefing and Debriefing
Briefing and debriefing time is critical to the proper implementation of the FITSphilosophy. Total time spent on each scenario should exceed 3-4 hours to include thebriefing time.
Use of Flight Training Devices
The use of flight training devices must be approved by the Cessna Pilot TrainingDepartment. This device must utilize software that is either the current version installedon new aircraft, or the version previous. Once approved, use of an FTD is done at thediscretion of the CFAI.
January 2010 Rev. I Cessna Aircraft Company 14
8/6/2019 CFAI Handbook 10a
15/27
GROUND TRAINING OUTLINE
PURPOSE: To provide the CFAI the guidance necessary to complete the groundtraining portions of the Cessna NAV III Transition Training Course. The ground trainingportion of the transition course will be completed with the assistance of the CessnaFITS Accepted Training Program and the G1000 PC-Trainer. Additional discussiontopics and interactive exercises are also provided to help increase the PTs knowledgeof the G1000.
Ground Training Module One: ClassroomSuggested Duration: 2 hours
Abbreviations:
PT: Pilot in Training
FD: Flight Director
FLC: Flight Level Change
1) Introduction\Orientation:
a) Welcome
b) Introductions
i) Instructor
ii) PTs
(1) Instructor Note: Allow each individual in the class to introduce
themselves and provide background and experience information as well
as the intended use of the aircraft. This allows the CFAI to become
familiar with everyones experience levels and creates an open
environment for questions and discussions.
c) Additional Discussion
i) Course Prerequisites
(1) It is encouraged for the PT to review all available reference materials.
Each aircraft owner may receive Garmin manuals. It is strongly
January 2010 Rev. I Cessna Aircraft Company 15
8/6/2019 CFAI Handbook 10a
16/27
recommended that renter pilots also have access to the reference
materials before participating in ground training to establish a foundation
of knowledge on the G1000. The Pilots Guide and Cockpit Reference
Guide can be downloaded from www.Garmin.com and the PC-Trainer can
also be ordered directly from Garmin via the website. It is also
recommended each PT meet the appropriate PIC/currency requirements
outlined by 14 CFR sections 61.56 and 61.57.
(2) Complete the Customer Information and Record of Training Form,
including the customer contact information.
(3) Consider and discuss additional endorsements:
(a) Biennial Flight Review
(b) Instrument Proficiency Check
(c) High-Performance Endorsement
(i) Instructors employed by Cessna Aircraft Company are not able to
sign PT logbooks, however, CFAIs are not restricted from signing
logbooks and may do so at the discretion of the CFAI.
(4) Questions, comments or suggestions should be directed to the Cessna
Pilot Training Department in Independence, Kansas, at (620) 332-0544
2) Training Approach
i) Ground Training Overview/Objective
ii) Flight Training Overview/Objective
iii) FITS Philosophy
(1) Definition
(2) Benefits
(3) Certificate
(a) Anyone completing the entire transition course under the guidance of a
factory-designated CFAI is eligible to receive the FITS certificate upon
receipt of the required documents by the Cessna Pilot Training
Department.
January 2010 Rev. I Cessna Aircraft Company 16
8/6/2019 CFAI Handbook 10a
17/27
(4) For additional information on FITS, please visit
www.faa.gov/education_research/training/fits/.
3) Display Overview:
a) Flight Indications
b) PFD
c) MFD
4) Operational Basics:
a) Bezel Controls
b) COM/NAV Tuning
c) Data Entry
d) MFD Navigation
5) Flight Director/Autopilot Introduction:
a) General Description
b) Limitations
c) Basic Operation
d) Other AFCS Controls
Ground Training Module One: Lab/Interactive Training SessionSuggested Duration: 2 hours
6) System Configuration
a) PFD Configuration
b) System Setup
c) MFD Navigation Map Overlays
7) Flight Scenario Content: Use the PC Trainer (or other training device) to fly the
sample scenario while covering the listed content allowing the customer to get as
much hands on experience as practical with the G1000 controls and features
before going to the airplane to fly Scenario 1.
January 2010 Rev. I Cessna Aircraft Company 17
http://www.faa.gov/education_research/training/fits/http://www.faa.gov/education_research/training/fits/8/6/2019 CFAI Handbook 10a
18/27
8/6/2019 CFAI Handbook 10a
19/27
i) Before departure
(1) Activate stored flight plan from catalog
ii) Enroute
(1) Enroute diversion around airspace or weather Direct to Map Pointer then
add the MAPWPT to flight plan
(2) Divert to alternate airport press D key and enter Waypoint (or place Map
Pointer on Waypoint then press D key (KSGF))
(3) Other Map Group Pages and other MFD information.
iii) Descent
(1) Direct to VNAV setup and capture
Ground Training Module Two: Lab/Interactive Training SessionSuggested Duration: 2 hours
Objective: Enhance understanding of G1000 Basics and introduce advanced multi-
function display features and autopilot instrument approach procedures.
8) Map setup Map group, Aviation group
9) Module II Lab Flight Scenario Content: Use the PC Trainer (or other training
device) to fly the sample scenario while covering the listed content allowing the
customer to get as much hands on experience as practical with the G1000 controls
and features before going to the airplane to fly Scenario 2.
a) NOTE: The slide sequence is new for version 10a and is provided only as an example of
the content that may be covered. It is highly recommended that the Garmin G1000 PC
Trainer (or other suitable training device) be used for this training content rather than the
slide sequence. A possible route is mentioned in the following outline but it is only a
suggestion. The CFAI should select a route appropriate to his/her training area.)
b) Leg 1
i) Before Taxi review from Module I as appropriate
January 2010 Rev. I Cessna Aircraft Company 19
8/6/2019 CFAI Handbook 10a
20/27
(1) Airport information Waypoint Group, frequency selection auto and
manual
ii) Before takeoff review from Module I as appropriate
(1) Altimeter setting, Selected Altitude, Fuel Calculator, Flight Plan with
airways (KIDP OSW V190 SGF KSGF), Transponder
iii) Departure
(1) Autopilot on HDG, NAV, FLC
(2) NAV capture Altitude capture
iv) Enroute
(1) Expanded MFD Page Groups and pages - (Tailor this section to the
customers needs address more commonly used pages (the bold
underlined ones) in more detail and limit time spent on other pages to a
brief overview)
(a) MAP Traffic, Stormscope, Weather Data Link (suggested item to cover: NEXRAD,
SIG/AIR, METAR, WIND, FRZ LVL), Terrain
(b) WPT Airport, Intersection, NDB, VOR, User
(c) NRST Airport, Intersection, NDB, VOR, User, Frequencies, Airspace Alerts (point
out Softkey function)
(d) AUX - Trip Planning, Utility, GPS Status, System Setup, XM Information, System
Status
v) Arrival
(1) Approach selection and loading (KSGF- ILS 14), Approach briefing (Show
Chart, BARO MIN), VNAV setup, VNAV capture, Activate approach
vi) Approach
(1) Approach mode of autopilot, Automatic NAV source change, Approach
tracking (LOC & GS)
vii) Missed approach
(1) Go Around Switch, Autopilot ON, NAV mode
c) Leg 2 (optional additional leg with GPS/RNAV approach if time permits)
January 2010 Rev. I Cessna Aircraft Company 20
8/6/2019 CFAI Handbook 10a
21/27
Ground Training Module Two: Classroom
Suggested Duration: 2 hours
19) Expanded MFD:
a) Review of MFD Pages/Page Groups
i) Traffic
ii) Stormscope
iii) Terrain
20) Instrument Approach Procedures/WAAS:
i) WAAS-General Operation
ii) LNAV, LNAV+V, LNAV/VNAV and LPV21) System Components:
a) Components
i) Abbreviations Review
ii) Functions
iii) Features
iv) Location
b) Audio Panel functions
22) System Malfunctions:
a) Advisory
b) Caution
c) Warning
d) Electrical Failure
e) Component Failures: All failures discuss affects on Autopilot Operations for both
KAP 140 and GFC-700
i) Display
ii) AHRS
iii) ADC
iv) Magnetometer
January 2010 Rev. I Cessna Aircraft Company 21
8/6/2019 CFAI Handbook 10a
22/27
v) Standby Instruments
vi) Audio Panel
23) Optional Systems
a) G1000 Systems
i) Synthetic Vision System
ii) TAS
iii) TAWS
b) Other Aircraft Systems
i) Amsafe Aviation Inflatable Restraints
ii) Turbo charging
iii) Oxygen
iv) McCauley Constant Speed Propeller
January 2010 Rev. I Cessna Aircraft Company 22
8/6/2019 CFAI Handbook 10a
23/27
FAILURE SIMULATION METHODS
Cessna does not recommend pulling breakers as a means to simulate failures on theGarmin G1000. Pulling breakers or using them as switches has the potential toweaken the breaker to a point where it may not perform its intended function. Usingbreakers as switches is also discouraged in Advisory Circulars 120-80, 23-17B, and43.13-1B. Additionally, a breaker may be powering other equipment (like avionicscooling fans) that could affect the safe operation of other equipment.
Failure to simulate Examiner action Applicant ActionLoss of AHRS andADC* (simulates the
loss of all primary flightinstrumentation)
Press the menu key on the Primary flightdisplay, or PFD. AUTO is highlighted in the
PFD DSPL field. If AUTO is nothighlighted, activate the cursor by pressingthe Flight Management System knob, orFMS knob. Turn the large, outer knob tomove the cursor to the AUTO field. Turnthe small, inner FMS knob towards thegreen arrow to select MANUAL. The cursorwill move to the percentage field. Turn thesmall, inner FMS knob counter-clockwise;adjust the backlit value to 0.14%, thelowest value. By pressing CLR and then
enter with cursor on this field, this willhappen instantly.An alternate method of simulating the lossof AHRS and ADC is to place a mask overthe affected information on the PFD. Whenusing this method one should avoid placinganything directly on the PFD screen whichcould damage the anti-glare coating on thescreen.
Control the aircraft byreference to the
backup attitude,altitude, and airspeedindicators.
January 2010 Rev. I Cessna Aircraft Company 23
8/6/2019 CFAI Handbook 10a
24/27
Loss of PFD Press the Display Backup button on thelower portion of the audio panel. Press theMenu key on the MFD and use the methoddescribed above to dim the PFD.
Control the aircraft byreference to the MFDin reversionary mode(This failure will
result in a loss of theGFC 700 AP and FD)
Loss of MFD Press the Display Backup button on thelower portion of the audio panel. Press theMenu key on the MFD. Use the large,outer FMS knob to move the cursor to theAUTO field adjacent MFD DSPL. Use theprocedures above to dim the MFD.
Control the aircraft byreference to the PFDin reversionary mode
*Note: The simulated loss of the AHRS and ADC individually cannot be accomplished in
the Cessna Nav III. In this simulated manner, the applicant must navigate the aircrafton a desired course during enroute or approach operations with the use of the movingmap display. The applicant or examiner may select the cross track (XTK) data bar fieldoption on the MFD to determine more precisely the horizontal distance from the desiredactive leg.
Below: The following picture is an example of the instrument cover/mask that can beused to simulate the previously discussed abnormal conditions. This cover is placedover the NAV and COM frequency selector knobs. It is located on the Program Disk.
Distance from center of COM knob, to center
of NAV knob is 10 5/16 inches.
January 2010 Rev. I Cessna Aircraft Company 24
8/6/2019 CFAI Handbook 10a
25/27
FLIGHT TRAINING OUTLINE
The flight training segment is completed with the guidance of the FAA Industry TrainingStandard (FITS) Scenario Based Transition Syllabus and Standards for Cessna SingleEngine Propeller Aircraft and the scripted scenarios developed by the CFAI andaccepted by the Cessna Pilot Training Department.
Scenario 1
Objective
PT will gain a basic knowledge and proficiency in avionics, aircraft systems and normal operatingprocedures.
Preflight Briefing Status
Risk Assessment _____
Weather Awareness, NOTAMs, TFRs _____
Brief Flight Scenarios _____
Differences in AFM / POH _____
Single Pilot Resource Management (SRM) _____
Appropriate & Current Aeronautical Charts _____
Weight & Balance _____
Introduce
Build a Flight Plan From Departure to Destination _____ Storing Flight Plans _____
Manual and Auto Frequency loading _____
Normal Takeoff / Landing _____
Autopilot Operation _____
VNAV _____
Normal Takeoff / Landing _____
Point Out Traffic, Terrain, & WX Awareness _____
Utilize NRST Function to Divert _____
Aircraft Maneuvers _____
Maneuvering with reference to the Flight Director _____
Cruise Procedures (Leaning with Lean Assist) _____
Normal Takeoff / Landing _____
Post Flight Briefing
Introduce Learner Centered Grading _____
Provide feedback & critique on performance of VFR PT _____
January 2010 Rev. I Cessna Aircraft Company 25
8/6/2019 CFAI Handbook 10a
26/27
Scenario 2
Objective
The IFR PT will gain a basic knowledge and proficiency in avionics and aircraft systems andnormal operating procedures while flying in the IFR environment.
Preflight Briefing Status
Brief Flight Scenario _____ Risk Assessment _____ Weather Awareness, NOTAMs, TFRs _____
Appropriate & Current Aeronautical Charts _____
Route of Flight Information for Each Leg _____ Choosing a Suitable Alternate _____
Loading IFR Flight Plans into G1000 _____
Weight & Balance _____
Review
Frequency Loading _____
Autopilot Operation _____
VNAV _____
TIS, Terrain, WX Awareness _____
Cruise Procedures _____
Introduce
Building a Flight Plan Using ATC Clearance _____
Loading airways into a Flight Plan _____ Load, Activate, & Fly an IAP _____
o Coupled ILS _____o Non-Precision with Procedure Turn
IP Choice of the Following LOC
VOR _____
GPS/GP
GPS w/o GP _____o Vector to Final Approach _____o Approach with DME Arc Transition _____
Missed Approaches _____ Circling Approaches _____ Published and non-published Holding Procedures _____
Post Flight Briefing Provide feedback & critique on performance of IFR PT _____
January 2010 Rev. I Cessna Aircraft Company 26
8/6/2019 CFAI Handbook 10a
27/27
Scenario 3
Objective
The PT will gain proficiency in the ability to recognize any failures of avionics and aircraft systemsand to apply corrective action in both the VFR and IFR environment.
Additionally, the PT will demonstrate the ability to make sound decisions, control the aircraft, anduse all available resources while dealing with these failures.
Preflight Briefing Status Risk Assessment _____
Weather Awareness, NOTAMs, TFRs _____
Review Section 3 of AFM _____ Brief Limitations on MFD as Primary Nav Source _____ Appropriate & Current Aeronautical Charts _____
Weight & Balance _____
Introduce
VFR PTo PFD Failure
Normal Approach & Landing _____o AHRS / ADC Failure
Normal Approach & Landing _____o ATC Assisted, AP Descent Through Clouds _____
IFR PTo PFD Failure
Instrument Approach _____o AHRS / ADC Failure
Instrument Approach _____
Alternator Failure and resulting indications _____
No Flap Takeoff & Landing
1. Post Flight Briefing
Provide feedback & critique on performance of PT _____
Recommended