View
3
Download
0
Category
Preview:
Citation preview
Autodesk CAD Management y estándares mundiales de
dibujo: hablemos el mismo idioma M.C. Sergio Raymundo Jaime Bernal
S1-1
Resumen de Curso: Formar grupos de trabajo en tiempo real, compartir la información entre empresas de especialidades diferentes, administrar y controlar grandes volúmenes de información en planos son algunas de nuestras necesidades; ¿cómo hacer para unificar criterios de dibujo?, ¿y los criterios de representación de información?, ¿cómo resuelven sus problemas de gestión y compartición de proyectos las grandes empresas?... ahora aprenderá cómo hacerlo.
Instructor: Sergio es reconocido por Autodesk como un capacitador profesional desde 1988. Es un Instructor Aprobado por Autodesk y es un Capacitador Técnico Certificado. Es el coordenador de la Comunidad Latinoamericana - de Usuarios de Autodesk en Español. Es considerado un especialista en infraestructura en Autodesk México y trabaja soportando a la cadena de distribuidores de productos de Autodesk. Obtuvo el grado de Licenciatura en Matemáticas por la Universidad Autónoma de Guadalajara. Curso estudios de maestria obteniendo el grado en Sistemas y Construction Project Management por la Universidad de California en los Ángeles y la Universidad Panamericana en México. Ha colaborado como profesor de tiempo completo impartiendo cátedra en Bases de Datos y programación estructurada. En la industria del software a colaborado con diversas casas editoriales como Osborne McGrawhill y editorial Iberoamérica traduciendo libros entre ellos del software de Autodesk. Ha colaborado como redactor en revistas de especialidad com Byte en México. También ha participado en la industria de la construcción a lo largo de 18 años en administración de proyectos, consultoría e implementación de tecnología de Software.
United States Version 3.1
National CAD StandardA Consensus Standard Incorporating Industry Publications
©2005. All rights reserved, including W
orld rights & Electronic rights. U
.S. copyright held by The Construction Specifications Institute. v07M
ar05a
United States Version 3.1
National CAD StandardA Consensus Standard Incorporating Industry Publications
M.C. Sergio Raymundo Jaime BernalConstruction Project Management
Autodesk Consultant
02 Noviembre 2007
©2005. All rights reserved, including W
orld rights & Electronic rights. U
.S. copyright held by The Construction Specifications Institute. v07M
ar05a
United States Version 3.1
National CAD StandardA Consensus Standard Incorporating Industry Publications
©2005. All rights reserved, including W
orld rights & Electronic rights. U
.S. copyright held by The Construction Specifications Institute. v07M
ar05a
AGENDA
• Composición & Conceptos
• Componentes
• Conclusiones
• Preguntas
• ¿Cómo ayudan los estándares?
LEY #1:Ningún Estándar puede estar basado en las Preferencias Individuales o en rasgos de personalidad
Consecuentemente, algunos individuos se resisten en adoptar los estándares puesto que estos entran en conflicto con sus preferencias personales o su personalidad.
LEY #2:Los Estándares no Pueden Responder a Cada Uno, o ajustarse a cualquier situación.
Sin embargo, esta no es una razón para desecharlos.
A pesar de que los estándares no son siempre “respuestas divinas”, estos ofrecen seguridad, incrementan la eficiencia y la interoperabilidad.
LEY #3Los Estándares evolucionan para ajustarse a las necesidades de la Industria.
Comprometerse con un estándar es comprometerse a un proceso de adaptación
LEY #4:La Implementación Inicial es casi siempredolorosa.
Debe compensar el dolor contra los beneficios.
©2005. All rights reserved, including W
orld rights & Electronic rights. U
.S. copyright held by The Construction Specifications Institute. v07M
ar05a
COMO AYUDAN LOS ESTÁNDARES**
LEYES INFLEXIBLES DE LA IMPLEMENTACIÓN
ImplementaciónESTÁNDARES
LEYES INFLEXIBLES
IMPLEMENTACIÓN DE ESTANDARES
• La Universalidad es Digna de Merecerse, pero no una meta Poco Realista
• Los Estándares evolucionan con la Industria
• La Implementación puede ser dolorosa
• Basados en más que Preferencias Individuales o en Rasgos de Personalidad
©2005. All rights reserved, including W
orld rights & Electronic rights. U
.S. copyright held by The Construction Specifications Institute. v07M
ar05a
COMO AYUDAN LOS ESTÁNDARES**
RELEVANCIA
RELEVANCIA
• Ingenieros (todo tipo)
• Estudiantes
• Académicos
• Arquitectos
¿Quienes deben involucrarse?
• Propietarios
• Especificadores
• Dibujantes
• Administradores
©2005. All rights reserved, including W
orld rights & Electronic rights. U
.S. copyright held by The Construction Specifications Institute. v07M
ar05a
NCS COMPOSICIÓN & CONCEPTOS**
DEFINICIÓN DE FACILITY
INSTALACION(FACILITY)
DEFINICIÓN:
Una estructura, o un grupo de estructuras, incluyendo la construcción en un terreno, que sirven a uno o más propósitos.
El NCS usa el término en el sentido más amplio.
©2005. All rights reserved, including W
orld rights & Electronic rights. U
.S. copyright held by The Construction Specifications Institute. v07M
ar05a
NCS COMPOSICIÓN & CONCEPTOS**
DEFINICIÓN DE CICLO DE VIDA
CICLO DEINSTALACIONES
• La información previa es la base de la continuidad del ciclo
• La información debe ser precisa & organizada
• La información debe ser fácil de recuperar & usar
©2005. All rights reserved, including W
orld rights & Electronic rights. U
.S. copyright held by The Construction Specifications Institute. v07M
ar05a
NCS COMPOSICIÓN & CONCEPTOS**
DEFINICIÓN DEL CICLO DE PROYECTO
CICLO DELPROYECTO
• El NCS se ajusta a las necesidades de los diferentes usuarios
• Muchos tipos de usuarios usan dibujos a todo lo largo del Ciclo de Proyecto
©2005. All rights reserved, including W
orld rights & Electronic rights. U
.S. copyright held by The Construction Specifications Institute. v07M
ar05a
NCS COMPOSICIÓN & CONCEPTOS**
CONCEPTOS DEL NATIONAL CAD STANDARD™
¿Qué esel NCS?
• Herramientas interrelacionadas, lineamientos y estándares de dibujo
• MasterFormat™, PageFormat™ y SectionFormat™organizan especificaciones; el NCS organiza dibujos
• Especificaciones para organizar el dibujo
• UDS- Uniform Drawing System (8 Módulos)
• Lineamientos de Layers de CAD
• Tri-Service Lineamientos de Ploteo
• Introducción y Apéndices
• Administradores del Desarrollo del NCS
• Instituciones Públicas/Privadas
NIBSAIACSITRI-SERVICES
©2005. All rights reserved, including W
orld rights & Electronic rights. U
.S. copyright held by The Construction Specifications Institute. v07M
ar05a
NCS COMPOSICIÓN & CONCEPTOS**
ORGANIZACIONES PARTICIPANTES
Julio 1999NCS Versión 1.0
• CSI UDS Módulos 01- 03• AIA Lineamientos de Layer de CAD 2nd Edition• Tri-Services Lineamientos de Ploteo• NIBS Introducción y Mejoras
2001NCS Versión 2.0
• CSI UDS Módulos 01-08• AIA Lineamientos de Layer de CAD: U.S. NCS V2.0• Tri-Services Lineamientos de Ploteo• NIBS Introducción y Mejoras
Agosto 2003CSI, AIA, NIBS Memorandum de Acuerdos (MOA)• Se Formaliza la Relación• Autoriza la NIBS licencias a los fabricantes de CAD a integrar el NCS dentro del Software
Julio 2004NCS Version 3.0
• AIA Lineamientos de Layer de CAD: U.S. NCS V3.0• Cambios a los módulos del CSI UDS Módulos 01-08• NIBS Introducción y Mejoras• La adquisición incluye la actualización NCS Version 3.1
Enero 2005NCS Version 3.1
• Incluye todos los cambios en el NCS V3.0• Documento en PDF en el CD ROM con búsquedas• Incluye las actualizaciones al MasterFormat™ 2004• Proporcionará licencias multiusuario
1998El concejo de CAD cambia aNIBS Facility Information Council (FIC)
©2005. All rights reserved, including W
orld rights & Electronic rights. U
.S. copyright held by The Construction Specifications Institute. v07M
ar05a
NCS COMPOSICIÓN & CONCEPTOS**
LÍNEA DEL TIEMPO DEL NCS
Línea del Tiempo
1997
1998
1999
2000
2002
2003
2004
2005
2001
2001
• 1998: NIBS Facility Information Council
• Jul 1999: NCS Versión 1.0
• Feb 2001: NCS Versión 2.0
• Ago 2003: CSI, NIBS, AIA- MOA
• Jul 2004: NCS Versión 3.0
• Ene 2005: NCS Versión 3.1
COMPONENTES
©2005. All rights reserved, including W
orld rights & Electronic rights. U
.S. copyright held by The Construction Specifications Institute. v07M
ar05a
United States Version 3.1
National CAD StandardA Consensus Standard Incorporating Industry Publications
AA - AAAA - AAAA - XGrupo Principal (obligatorio)
©2005. All rights reserved, including W
orld rights & Electronic rights. U
.S. copyright held by The Construction Specifications Institute. v07M
ar05a
NCS: AIA LINEAMIENTOS DE LAYER DE CAD**
AIA VISTA PREVIA DE LOS LINEAMIENTOS DE LAYERS
AIA LINEAMIENTOS
DE LAYERS DE CAD
AA - AAAA - AAAA - XDenominadores de Disciplina (obligatorio)
AA - AAAA - AAAA - XUno o Dos Grupos Secundarios (opcional)
AA - AAAA - AAAA - XEstado (opcional)
©2005. All rights reserved, including W
orld rights & Electronic rights. U
.S. copyright held by The Construction Specifications Institute. v07M
ar05a
NCS: AIA LINEAMIENTOS DE LAYER DE CAD**
DENOMINADORES DE DISCIPLINA
DENOMINADORESDE DISCIPLINA
• Uno o dos caracteres alfabéticos
• Obligatorio
• Coordinado con la Organización de Conjuntos de Dibujos
G GeneralH Hazardous MaterialsV Survey / MappingB GeotechnicalW Civil WorksC CivilL LandscapeS StructuralA ArchitecturalI InteriorsQ EquipmentF Fire ProtectionP PlumbingD ProcessM MechanicalE ElectricalT TelecommunicationsR ResourceX Other DisciplinesZ Contractor/Shop DrawingsO Operations
AI Architectural Interiors
AS Architectural SiteAD Architectural
DemolitionCG Civil GradingCP Civil PavingSF Structural FramingDP Process PipingEL Electrical Lighting
NIVEL 1 (obligatorio) NIVEL 2 (opcional)
©2005. All rights reserved, including W
orld rights & Electronic rights. U
.S. copyright held by The Construction Specifications Institute. v07M
ar05a
NCS: AIA LINEAMIENTOS DE LAYER DE CAD**
DENOMINADORES PRINCIPALES DE GRUPOS
DenominadoresDe GruposPrincipales
• Identifica: Sistemas Principales de
Edificación o
Vistas de dibujos, o,
Anotaciones.
•Obligatorio
• Coordinado con la Organización de
Conjuntos de Dibujos
• Definidos por el Usuario
Los Grupos Principales NO son Permitidos
Sistemas Principales de EdificaciónWALL WallsDOOR DoorsLITE Lighting FixturesFIXT Plumbing Fixtures
Vistas de Dibujos (para Layers organizados por tipo) SECT SectionsELEV ElevationsDETL Details
AnotacionesANNO Annotations
©2005. All rights reserved, including W
orld rights & Electronic rights. U
.S. copyright held by The Construction Specifications Institute. v07M
ar05a
NCS: AIA LINEAMIENTOS DE LAYER DE CAD**
DENOMINADORES SECUNDARIOS DE GRUPOS
DenominadoresDe Grupos
Secundarios
• Se diferencian de un grupo principal
• Uno o dos conjuntos de cuatro caracteres
• Opcional
• Puede ser definido por el usuario: A-Z, 0-9, ~
FULL Full HeightPART PartialIDEN Identification PATT Pattern
©2005. All rights reserved, including W
orld rights & Electronic rights. U
.S. copyright held by The Construction Specifications Institute. v07M
ar05a
NCS: AIA LINEAMIENTOS DE LAYER DE CAD**
DENOMINADOR DEL CAMPO DE ESTADO
DENOMINADORESDEL CAMPODE ESTADO
• Diferencian la fase de construcción o el tipo
• Opcional
N Trabajo NuevoE Existe y permaneceráD Existe y se demoleráF Trabajo FuturoT Trabajo TemporalM Elementos a ser MovidosX No se encuentra en el Contrato1-9 Números de Fase
©2005. All rights reserved, including W
orld rights & Electronic rights. U
.S. copyright held by The Construction Specifications Institute. v07M
ar05a
NCS: AIA LINEAMIENTOS DE LAYER DE CAD**
EJEMPLOS DE NOMBRES DE LAYERS
EJEMPLOS DE NOMBRES DE
LAYERS• Conocidos por su
Flexibilidad
C-BORE [Test Borings] L-SITE-PLAY [Site Improvements:
Play Structures]A-FLOR-TPTN [Floor: Toilet Partitions]Q-CASE-UPPR [Casework: Upper Cabinets]D-PGAS-H2 [Gas: Hydrogen – System]E-LITE-CIRC-EMER [Lighting Circuits:
Emergency]M-FUME-E [Fume Hood: Existing to
Remain]
Ejemplos de Nombres de Layers:
©2005. All rights reserved, including W
orld rights & Electronic rights. U
.S. copyright held by The Construction Specifications Institute. v07M
ar05a
NCS: AIA LINEAMIENTOS DE LAYER DE CAD**
MEJORAS DE LA VERSION 3.1
VERSIÓN 3.1MEJORAS
• Regla del “Agente Libre”
• Denominador de Disciplina de dos caracteres
• Lista de LayersExpandida
• Comentario de Cumplimiento ISO
•Actualizado al MasterFormat™2004
©2005. All rights reserved, including W
orld rights & Electronic rights. U
.S. copyright held by The Construction Specifications Institute. v07M
ar05a
CSI’S UDS:UNIFORMDRAWINGSYSTEM
NCS: CSI’S UNIFORM DRAWING SYSTEM (UDS)**
SISTEMA DE DIBUJO UNIFORME DEL NCS
©2005. All rights reserved, including W
orld rights & Electronic rights. U
.S. copyright held by The Construction Specifications Institute. v07M
ar05a
ORGANIZACIÓN DECONJUNTOS DE DIBUJOS
NCS: CSI’S UNIFORM DRAWING SYSTEM (UDS)**
ORGANIZACIÓN DE CONJUNTOS DE DIBUJOS: MÓDULO 01
Módulo 01
©2005. All rights reserved, including W
orld rights & Electronic rights. U
.S. copyright held by The Construction Specifications Institute. v07M
ar05a
O - OPERATIONSZ - CONTRACTOR/SHOP DRAWINGSX - OTHER DISCIPLINESR - RESOURCET - TELECOMMUNICATIONSE - ELECTRICALM - MECHANICALD - PROCESSP - PLUMBINGF - FIRE PROTECTION
Q - EQUIPMENTI - INTERIORSA - ARCHITECTURALS - STRUCTURALL - LANDSCAPEC – CIVILW – CIVIL WORKSB – GEOTECHNICALV – SURVEY/MAPPINGH – HAZ MATERIALS
G - GENERALLIST OFSHEETS
JERARQUIASEN LAS
DISCIPLINAS
• Organice las hojas como en la ilustración
• Algunas, Todas, o la Mayoría de las Categorías pueden Aplicar
NCS: CSI’S UNIFORM DRAWING SYSTEM (UDS)**
JERARQUÍA DE LOS CONJUNTOS DE DIBUJO
©2005. All rights reserved, including W
orld rights & Electronic rights. U
.S. copyright held by The Construction Specifications Institute. v07M
ar05a
IDENTIFICACIÓNESTÁNDARDE LA HOJA
• Nivel 2 del Denominador de Disciplina opcional
• El Guión debe seguir al Denominador de Disciplina
NCS: CSI’S UNIFORM DRAWING SYSTEM (UDS)**
IDENTIFICACIÓN DE LA HOJA
A(A) - NNNDenominadores de Disciplina (Niveles 1 & 2)
AA - NNNDenominador del Tipo de Hoja
AA - NNNNúmero de Secuencia de la Hoja
A = Carácter alfabético
N = Carácter numérico
©2005. All rights reserved, including W
orld rights & Electronic rights. U
.S. copyright held by The Construction Specifications Institute. v07M
ar05a
DENOMINADORDE DISCIPLINA
• Modifica el Nivel 2
• Nivel 2 Opcional
• El guión debeseguir a losdenominadores
NCS: CSI’S UNIFORM DRAWING SYSTEM (UDS)**
DENOMINADORES DE DISCIPLINA
G GeneralH Hazardous MaterialsV Survey/ MappingB GeotechnicalW Civil WorksC CivilL LandscapeS StructuralA ArchitecturalI InteriorsQ EquipmentF Fire ProtectionP PlumbingD ProcessM MechanicalE Electrical
A - NNN
A A - NNN
T TelecommunicationsR ResourceX Other DisciplinesZ Contractor/ Shop DrawingsO Operations
AS Architectural SiteCD Civil DemolitionQL Laboratory EquipmentFX Fire SuppressionEP Electrical PowerEL Electrical LightingTT Telephone
©2005. All rights reserved, including W
orld rights & Electronic rights. U
.S. copyright held by The Construction Specifications Institute. v07M
ar05a
NCS: CSI’S UNIFORM DRAWING SYSTEM (UDS)**
DENOMINADORES DE TIPO DE HOJA Y DE SECUENCIA
DENOMINADORESDE TIPO DE
HOJA & SECUENCIA
• *Denominadores de Tipo de Hoja Definidos por Usuario Pudieran NO Caer en Otras Categorías
• Siempre incluya una secuencia de Denominador de2 dígitos
• NO use el “00”
TIPO DE HOJA0 General (símbolos,
leyendas, notas, etc.)1 Plantas (horizontal)2 Elevaciones (vertical)3 Secciones(muros y
escaleras)4 Vistas a Gran Escala5 Detalles6 Tablas y Diagramas
AA – N NN
AA – N NN
7 Definido por Usuario* 8 Definido por Usuario* 9 Representaciones
3D (isométricos,perspectivas,fotografías)
SECUENCIA01-99
©2005. All rights reserved, including W
orld rights & Electronic rights. U
.S. copyright held by The Construction Specifications Institute. v07M
ar05a
MUESTRA DEDENOMINADORES
DE DIBUJOS
NCS: CSI’S UNIFORM DRAWING SYSTEM (UDS)**
EJEMPLOS DE NOMBRES DE HOJA
Hoja Título de la HojaG - 001 Title SheetC - 001 Notes and SymbolsS - 101 Foundation PlanA - 101 Floor PlanA - 201 Exterior ElevationsA - 301 Wall SectionsA - 601 Door and Frame ScheduleP - 101 Plumbing Site PlanP - 601 Plumbing Riser DiagramM - 101 HVAC PlanE - 101 Power PlanE - 102 Lighting PlanE - 501 Electrical Details
©2005. All rights reserved, including W
orld rights & Electronic rights. U
.S. copyright held by The Construction Specifications Institute. v07M
ar05a
• Un guión debe seguir al Denominador de Disciplina de Nivel 2 (Nuevo)
NCS: CSI’S UNIFORM DRAWING SYSTEM (UDS)**
EJEMPLOS DE NOMBRES DE HOJAS
Hoja Título de la HojaCD-101 Site Demolition PlanCG-101 Grading PlanLI-101 Landscape Irrigation PlanSF-101 Roof Framing PlanSF-501 Framing DetailsAS-101 Architectural Site PlanAG-101 Signage PlanIN-601 Interior Finish SchedulesES-101 Electrical Site PlanEP-101 Electrical Power PlanEL-101 Electrical Lighting PlanTI-101 Intercom Plan
MUESTRA DEDENOMINADORES
DE DIBUJOS
©2005. All rights reserved, including W
orld rights & Electronic rights. U
.S. copyright held by The Construction Specifications Institute. v07M
ar05aMF 2004
COORDINACIÓN
• NCS 3.1 Coordinado con elMasterFormat™2004
NCS: CSI’S UNIFORM DRAWING SYSTEM (UDS)**
NCS Y EL MASTERFORMAT™ 2004
AA - AAAA - AAAA - XGrupo Principal (obligatorio)
©2005. All rights reserved, including W
orld rights & Electronic rights. U
.S. copyright held by The Construction Specifications Institute. v07M
ar05a
NCS: AIA LINEAMIENTOS DE LAYER DE CAD**
AIA VISTA PREVIA DE LOS LINEAMIENTOS DE LAYERS
AIA LINEAMIENTOS
DE LAYERS DE CAD
AA - AAAA - AAAA - XDenominadores de Disciplina (obligatorio)
AA - AAAA - AAAA - XUno o Dos Grupos Secundarios (opcional)
AA - AAAA - AAAA - XEstado (opcional)
©2005. All rights reserved, including W
orld rights & Electronic rights. U
.S. copyright held by The Construction Specifications Institute. v07M
ar05a
ORGANIZACIÓN DE LA HOJA
NCS: CSI’S UNIFORM DRAWING SYSTEM (UDS)**
ORGANIZACIÓN DE LA HOJA: MÓDULO 02
MÓDULO 02
©2005. All rights reserved, including W
orld rights & Electronic rights. U
.S. copyright held by The Construction Specifications Institute. v07M
ar05aTamañosComunesde Planos
NCS: CSI’S UNIFORM DRAWING SYSTEM (UDS)**
TAMAÑOS COMUNES DE HOJA
MARCA TAMAÑO mm (in) USOS TÍPICOSA 216 x 279 (8.5 x 11) Libro de Proyecto; dibujos
suplementarios; dibujos preliminares.
B 279 x 432 (11 x 17) Dibujos suplementarios; dibujos preliminares.
C 432 x 559 (17 x 22) Proyectos pequeños con escalas deseadas de planos.
D 559 x 864 (22 x 34) Proyectos con escaladas deseadas de planos; proyectos de gobierno.
E 864 x 1118 (34 x 44) Proyectos grandes con escalas deseadas de planos; mapas & GIS.
NO MOSTRADAS:
A0-A4, A-F
©2005. All rights reserved, including W
orld rights & Electronic rights. U
.S. copyright held by The Construction Specifications Institute. v07M
ar05a
DISTRIBUCIÓNDE LA HOJA
• Área de Datos deProducción
NCS: CSI’S UNIFORM DRAWING SYSTEM (UDS)**
AREAS DE DISTRIBUCIÓN DE LA HOJA
• Área de Dibujo
• Área del Block deTítulo
©2005. All rights reserved, including W
orld rights & Electronic rights. U
.S. copyright held by The Construction Specifications Institute. v07M
ar05a
NCS: CSI’S UNIFORM DRAWING SYSTEM (UDS)**
ÁREA DE DATOS DE PRODUCCIÓN
ÁREA DE DATOSDE PRODUCCIÓN
• Información deProducción:
•Block de Producción
•Ruta del Archivo
•Nombre de archivo
•Parámetros por default
•Asignación de Plumillas
•Comandos de Impresión
•Datos de Control de Sobreposición del dibujo
•Archivo(s) de Referencia
•Layers graficados
•Horas de Producción
•Escaneo del block de escala
©2005. All rights reserved, including W
orld rights & Electronic rights. U
.S. copyright held by The Construction Specifications Institute. v07M
ar05a
Contenidos:
• Keynotes
• Key plans
• Diagramas y Tablas
• Otra información gráfica
NCS: CSI’S UNIFORM DRAWING SYSTEM (UDS)**
ÁREA DE DIBUJO
AREA DE DIBUJO
ÁREA DEDIBUJO
©2005. All rights reserved, including W
orld rights & Electronic rights. U
.S. copyright held by The Construction Specifications Institute. v07M
ar05a
• Dividida en Módulos
• Las Columnas son números
• Los renglones son Letras
NCS: CSI’S UNIFORM DRAWING SYSTEM (UDS)**
RETÍCULA DEL ÁREA DE DIBUJO
A
B
C
D
1 2 3 4 5A
B
C
D1 2 3 4 5
ÁREA DEDIBUJO
©2005. All rights reserved, including W
orld rights & Electronic rights. U
.S. copyright held by The Construction Specifications Institute. v07M
ar05a
• Módulos Identificados por Letra & Número
• Un Dibujo Puede Comprender Varios Módulos
• Use las Coordenadas del Módulo como Identificador
NCS: CSI’S UNIFORM DRAWING SYSTEM (UDS)**
MÓDULO EN LA RETÍCULA DEL ÁREA DE DIBUJO
A
B
C
D
1 2 3 4 5A
B
C
D1 2 3 4 5
MÓDULO **
ÁREA DEDIBUJO
©2005. All rights reserved, including W
orld rights & Electronic rights. U
.S. copyright held by The Construction Specifications Institute. v07M
ar05a
• El Número de Dibujo como se Determinó por la Coordenada
NCS: CSI’S UNIFORM DRAWING SYSTEM (UDS)**
NÚMERO DE DIBUJO
XXXXX
XX
XXXXX
XXX
XXXXXXXX XXXX XXXXXXX:X
GRIDXXXX
XXX XX XX
XXXX
XXXX
XXX
C4
ÁREA DEDIBUJO
©2005. All rights reserved, including W
orld rights & Electronic rights. U
.S. copyright held by The Construction Specifications Institute. v07M
ar05a
Contenidos:
• Diseñador
• Proyecto
• Block de Revisiones
• Cliente/ Administración
• Título de la Hoja
• Información de Identificación de la Hoja
NCS: CSI’S UNIFORM DRAWING SYSTEM (UDS)**
ÁREA DE BLOCK DE TÍTULO
ÁREA DEBLOCK DE
TÍTULO
©2005. All rights reserved, including W
orld rights & Electronic rights. U
.S. copyright held by The Construction Specifications Institute. v07M
ar05a**ALINEAMIENTO DEL BLOCK DE TÍTULO
Formato de Texto Horizontal:
Form
ato
de T
exto
Ver
tical
:
ÁREA DEBLOCK DE
TÍTULO
NCS: CSI’S UNIFORM DRAWING SYSTEM (UDS)
Contenidos:
©2005. All rights reserved, including W
orld rights & Electronic rights. U
.S. copyright held by The Construction Specifications Institute. v07M
ar05a**COMPONENTES DEL BLOCK DEL DISEÑADOR
BLOCK DEID DEL
DISEÑADOR
• Nombre
• Dirección
• Teléfono & Fax
• Dirección de E-mail
• Consultores
• Sellos Profesionales
NCS: CSI’S UNIFORM DRAWING SYSTEM (UDS)
©2005. All rights reserved, including W
orld rights & Electronic rights. U
.S. copyright held by The Construction Specifications Institute. v07M
ar05a
Contenidos:
• Nombre del Proyecto
• Dirección del Proyecto
• Nombre de la Edificación/Instalación
• Secuencia de Fase de Construcción
• Logo de Proyecto
**COMPONENTES DEL BLOCK DE ID DEL PROYECTO
BLOCK DEID DEL
PROYECTO
NCS: CSI’S UNIFORM DRAWING SYSTEM (UDS)
©2005. All rights reserved, including W
orld rights & Electronic rights. U
.S. copyright held by The Construction Specifications Institute. v07M
ar05a
Contenidos:
• Fechas de las Fases o Etapas
• Fechas de Agregados
• Fechas de Aclaraciones
• Fechas de Revisiones
**COMPONENTES DEL BLOCK DE REVISIONES
BLOCK DEREVISIONES
NCS: CSI’S UNIFORM DRAWING SYSTEM (UDS)
©2005. All rights reserved, including W
orld rights & Electronic rights. U
.S. copyright held by The Construction Specifications Institute. v07M
ar05a
Contenidos:
• Número de Proyecto de Quien Prepara el Dibujo
• Número de Archivo de Dibujo CAD
• Dibujado por• Revisado por• Derechos de
Propiedad
Siempre Horizontal, sin importar el formato del texto
**COMPONENTES DEL BLOCK DE ADMINISTRACIÓN
BLOCK DEADMINISTRACIÓN
NCS: CSI’S UNIFORM DRAWING SYSTEM (UDS)
©2005. All rights reserved, including W
orld rights & Electronic rights. U
.S. copyright held by The Construction Specifications Institute. v07M
ar05a
• Siempre Horizontal, sin importar elformato de texto
**BLOCK DEL TÍTULO DE LA HOJA Y DEL ID DE LA HOJA
BLOCK DELTÍTULO DE
LA HOJA & ID
NCS: CSI’S UNIFORM DRAWING SYSTEM (UDS)
©2005. All rights reserved, including W
orld rights & Electronic rights. U
.S. copyright held by The Construction Specifications Institute. v07M
ar05a**SCHEDULES: MÓDULO 03
MÓDULO 03
ROOM FINISH SCHEDULE
ROOM # ROOM NAME FLOOR BASE WALL CEILING NOTES
101 ENTRY VCT RUBBER PAINT SAP 1
102 OFFICE CPT RUBBER PAINT SAP 2
DIAGRAMAS & TABLAS
NCS: CSI’S UNIFORM DRAWING SYSTEM (UDS)
©2005. All rights reserved, including W
orld rights & Electronic rights. U
.S. copyright held by The Construction Specifications Institute. v07M
ar05a
Objetivos:
• Consistencia• Sistematización
Contiene 4 Partes:
1. Título (Encabezado)
2. Columna de ID (Marca)
3. Descripción4. Características
Distintivas
**COMPONENTES DE DIAGRAMAS & TABLAS
DIAGRAMAS&
TABLAS
MARCA DESCRIPCIÓN CARACTERÍSTICA
ENCABEZADO
NCS: CSI’S UNIFORM DRAWING SYSTEM (UDS)
©2005. All rights reserved, including W
orld rights & Electronic rights. U
.S. copyright held by The Construction Specifications Institute. v07M
ar05a
• También puede incluir Notas
• Al incluir Notas se ahorra espacio en el diagrama
**NOTAS DE DIAGRAMAS & TABLAS
DIAGRAMAS &TABLAS
Notas:1 Nota A2 Nota B3 Nota C
MARCA ELEMENTO CARACTERÍSTICA NOTAS
ENCABEZADO
1
NCS: CSI’S UNIFORM DRAWING SYSTEM (UDS)
NOTES
©2005. All rights reserved, including W
orld rights & Electronic rights. U
.S. copyright held by The Construction Specifications Institute. v07M
ar05a
Una Sola Fila
Sub-Columnas: Doble Fila
Encabezados
ID de Columnas
Sub-ID de Columna
ID de Renglón
Celda de Descripción
**FILAS EN DIAGRAMAS & TABLAS
FILAS
ROOM FINISH SCHEDULEROOM NO
ROOM NAME FLOOR BASE WALL CEILING NOTES
101 ENTRY VCT RUBBER PAINT SAP 1
102 OFFICE CPT RUBBER PAINT SAP 2
MARK DESCRIPTION MFR MODEL SUPPLYFITTING
SUPPLYPIPE(S)
CONNECTIONS
CW HW WASTE VENTDRAIN TRAP
PLUMBING FIXTURE SCHEDULE
NCS: CSI’S UNIFORM DRAWING SYSTEM (UDS)
©2005. All rights reserved, including W
orld rights & Electronic rights. U
.S. copyright held by The Construction Specifications Institute. v07M
ar05a
• Depende del Proyecto/Cliente
• Diagramas Simples (pe., Sellador) localizado al final de las Secciones Especificaciones
• Los Diagramas Cubren Múltiples Secciones: Se Localizan en los Dibujos
• O: Puede estar localizada en al sección dedicada al MF 2004
**DIAGRAMA DE UBICACIÓN
DIAGRAMA DEUBICACIÓN
Diagrama de Ubicaciones en el Manual de Proyecto:
Nuevo en el NCS versión 3.1:Los Diagramas con productos de múltiples secciones pueden ahora localizarse en el manual de proyecto de acuerdo al número del MasterFormat™ 2004
NCS: CSI’S UNIFORM DRAWING SYSTEM (UDS)
©2005. All rights reserved, including W
orld rights & Electronic rights. U
.S. copyright held by The Construction Specifications Institute. v07M
ar05a**ACUERDOS DE DIBUJO: MÓDULO 04
MÓDULO 04
ACUERDOS DE DIBUJO
NCS: CSI’S UNIFORM DRAWING SYSTEM (UDS)
©2005. All rights reserved, including W
orld rights & Electronic rights. U
.S. copyright held by The Construction Specifications Institute. v07M
ar05a
Incluye:
• Orientación delDibujo y Flecha del Norte
• Sistema de Retícula
• Formato del Block de Dibujo
• Distribucióndel Dibujo
• Escala
• Líneas
• Dimensiones
**REVISIÓN DE LOS ACUERDOS DE DIBUJO
ACUERDOSDE DIBUJO
ACUERDOS DE DIBUJO
NCS: CSI’S UNIFORM DRAWING SYSTEM (UDS)
©2005. All rights reserved, including W
orld rights & Electronic rights. U
.S. copyright held by The Construction Specifications Institute. v07M
ar05a
Temas Cubiertos:
• Indicaciones de Materiales
• Referencias Cruzadas
• Símbolos• Tipos de Dibujo
GeneralPlantasElevacionesSecciones (Cortes)Vistas a Gran Esc.Detalles Tablas & Diagramas3-D Representaciones
• Dibujos Preliminares
**REVISIÓN DE LOS ACUERDOS DE DIBUJO
ACUERDOSDE DIBUJO
ACUERDOS DE DIBUJO
NCS: CSI’S UNIFORM DRAWING SYSTEM (UDS)
©2005. All rights reserved, including W
orld rights & Electronic rights. U
.S. copyright held by The Construction Specifications Institute. v07M
ar05a
• Lados del Edificio paralelos a los lados de la hoja
• La orientación de un detalle es la misma que la de la planta
**ORIENTACIÓN & FLECHA DEL NORTE
ORIENTACIÓN& FLECHA
DEL NORTE
NCS: CSI’S UNIFORM DRAWING SYSTEM (UDS)
©2005. All rights reserved, including W
orld rights & Electronic rights. U
.S. copyright held by The Construction Specifications Institute. v07M
ar05a
Anchode LíneasAnchos de líneas en mm
Fino 0.18
Delgado 0.25
Medio 0.35
Ancho 0.50
Extra Ancho 0.70
**ANCHO DE LÍNEAS
1.00
1.40
2.00
NCS: CSI’S UNIFORM DRAWING SYSTEM (UDS)
©2005. All rights reserved, including W
orld rights & Electronic rights. U
.S. copyright held by The Construction Specifications Institute. v07M
ar05a
• Cada puerta tiene un ID único
• El número de la puerta es el mismo que el número de la habitación
• Puertas Múltiples se etiquetan con sufijos A-Z(Nuevo símbolo del NCS 3.1)
**SÍMBOLOS DE PUERTAS
EJEMPLO
ALMACEN
151ALMACEN
152
152A
152B
151
NCS: CSI’S UNIFORM DRAWING SYSTEM (UDS)
©2005. All rights reserved, including W
orld rights & Electronic rights. U
.S. copyright held by The Construction Specifications Institute. v07M
ar05a
• Retícula Vertical en la parte Superior, Numerada de Izquierda a Derecha
• Retícula Horizontal a la Derecha, en orden alfabético de abajo hacia arriba
**INDICADORES DE LA RETÍCULA DE REFERENCIA
RETÍCULA DEREFERENCIA
3 4 521
D
C
B
A
INDICADORES DE LA RETÍCULA DE REFERENCIA
NCS: CSI’S UNIFORM DRAWING SYSTEM (UDS)
©2005. All rights reserved, including W
orld rights & Electronic rights. U
.S. copyright held by The Construction Specifications Institute. v07M
ar05a
• Orientación Consistente
**MARCADORES
MARCADORES
NCS: CSI’S UNIFORM DRAWING SYSTEM (UDS)
©2005. All rights reserved, including W
orld rights & Electronic rights. U
.S. copyright held by The Construction Specifications Institute. v07M
ar05a**COMPONENTES DEL BLOCK DE DIBUJO
FORMATO DELBLOCK DE
DIBUJO
SECCIÓN**
X:X
XXXXX
XX
XXXXX
XXX
RETXXXX
XXX XX XX
XXXX
XXXX
XXX
NCS: CSI’S UNIFORM DRAWING SYSTEM (UDS)
Retícula de Referencia & Área de Dimensiones
Área de Notación Gráfica
Margen
Área de Título
Líneas del Módulo de Dibujo
©2005. All rights reserved, including W
orld rights & Electronic rights. U
.S. copyright held by The Construction Specifications Institute. v07M
ar05a
Líneas de DibujoDel Módulo
ID del Dibujo
Número del Dibujo
Título del Dibujo
Escala del Dibujo
Flecha del Norte
Escala Gráfica (Opcional)
**ÁREA DEL BLOCK DE TÍTULO
ÁREA DETÍTULO
SECCIÓN**
X:X X X X X X
NCS: CSI’S UNIFORM DRAWING SYSTEM (UDS)
©2005. All rights reserved, including W
orld rights & Electronic rights. U
.S. copyright held by The Construction Specifications Institute. v07M
ar05a
• Simplifica & organiza
• Estandariza la ubicación de componentes de dibujos
• Estandariza la ubicación de la información para todos los dibujos
• Formato Consistente para todos los dibujos
• Trabaja con todos los proyectos sin importar su tamaño
**BENEFICIOS DEL NCS
BENEFICIOS
SECCIÓN**
X:X
XXXXX
XX
XXXXX
XXX
RETXXXX
XXX XX XX
XXXX
XXXX
XXX
NCS: CSI’S UNIFORM DRAWING SYSTEM (UDS)
PRIMER DIBUJOSEGUNDO DIBUJOTERCER DIBUJOCUARTO DIBUJO
©2005. All rights reserved, including W
orld rights & Electronic rights. U
.S. copyright held by The Construction Specifications Institute. v07M
ar05a
Localice el block de dibujo usado frecuentemente en la parte más baja, por título
Muévase hacia Arriba, a la Izquierda
**UBICACIÓN Y LOCALIZACIÓN DEL BLOCK
UBICACIÓNDEL BLOCK
BLOCK DE NOTAS
NCS: CSI’S UNIFORM DRAWING SYSTEM (UDS)
©2005. All rights reserved, including W
orld rights & Electronic rights. U
.S. copyright held by The Construction Specifications Institute. v07M
ar05a**TÉRMINOS Y ABREVIATURAS: MÓDULO 05
MÓDULO 05
TÉRMINOS & ABREVIATURAS
NCS: CSI’S UNIFORM DRAWING SYSTEM (UDS)
©2005. All rights reserved, including W
orld rights & Electronic rights. U
.S. copyright held by The Construction Specifications Institute. v07M
ar05a
Incluye:
• Términos Preferidos
• Abreviaturas Estándar en Dibujos
• Cuándo usar Abreviaturas
• Formatos de las Abreviaturas
**REVISIÓN DE TÉRMINOS Y ABREVIATURAS
MÓDULO 05
TÉRMINOS & ABREVIATURAS
NCS: CSI’S UNIFORM DRAWING SYSTEM (UDS)
©2005. All rights reserved, including W
orld rights & Electronic rights. U
.S. copyright held by The Construction Specifications Institute. v07M
ar05a**REVISIÓN DE TÉRMINOS Y ABREVIATURAS
MÓDULO 05
Proporciona:
• Comunicación Consistente
• Términos Consistentes
• Notas de Uso Común y Terminología que no se prefiere
TÉRMINOS & ABREVIATURAS
NCS: CSI’S UNIFORM DRAWING SYSTEM (UDS)
©2005. All rights reserved, including W
orld rights & Electronic rights. U
.S. copyright held by The Construction Specifications Institute. v07M
ar05a
Panel para Muro de Yeso
Muro de Yeso
Tabla de Yeso
Tablarroca
Muro Aparente de Yeso
Panel de Yeso
**EXÁMEN DE TÉRMINOS PREFERIDOS: ESTE PRODUCTO
EXAMEN DETERMINOS
PREFERIDOS
NCS: CSI’S UNIFORM DRAWING SYSTEM (UDS)
©2005. All rights reserved, including W
orld rights & Electronic rights. U
.S. copyright held by The Construction Specifications Institute. v07M
ar05a**EXÁMEN DE TÉRMINOS PREFERIDOS: ESTE PRODUCTO
Calafatear
Calafateo
Relleno
Rellenado
Sellador
EXAMEN DETERMINOSPREFERIDOS
NCS: CSI’S UNIFORM DRAWING SYSTEM (UDS)
©2005. All rights reserved, including W
orld rights & Electronic rights. U
.S. copyright held by The Construction Specifications Institute. v07M
ar05a**EXÁMEN DE ABREVIATURAS PREFERIDAS: “ELEVACIÓN”
El
EL
Elev
ELEV
ELV
EXAMEN DEABREVIATURAS
PREFERIDAS
NCS: CSI’S UNIFORM DRAWING SYSTEM (UDS)
©2005. All rights reserved, including W
orld rights & Electronic rights. U
.S. copyright held by The Construction Specifications Institute. v07M
ar05a
• No Minúsculas
• No Puntos
• No Abreviar Palabras de Menos de 5 Letras
• Evitar las Abreviaturas cuando sea Posible
**REGLAS GENERALES DE LAS ABREVIATURAS
REGLASGENERALES
Palabra Sí NoElevation EL ElGypsum Board GYP BD Gyp BdEquals EQ Eq
Invert Elevation INV EL INV. EL.Catch Basin CB C.B.Typical TYP TYP.
If thr cn be any dbt / cnfsn abtabbrv mnng, DN’T USE.
NCS: CSI’S UNIFORM DRAWING SYSTEM (UDS)
©2005. All rights reserved, including W
orld rights & Electronic rights. U
.S. copyright held by The Construction Specifications Institute. v07M
ar05a**SÍMBOLOS: MÓDULO 06
MÓDULO 06
3D2
A-512
2
SÍMBOLOSIncluye:
• Clasificación deSímbolos
• Alrededor de 6,000 Representaciones Gráficas de Símbolos
• Cómo están organizados los Símbolos
NCS: CSI’S UNIFORM DRAWING SYSTEM (UDS)
Indicador de Referencia
SD Drenaje Pluvial
EL 100Indicador de ElevaciónExistente
ConstrucciónResistente alFuego 1-3 hrs
‘‘‘&@+/-X#x o
Pie (pies)Pulgada (pulgadas)yenMás oMenosMultiplicar por,porNúmero,LibraGrado(s)Tierra
Ladrillo
Terminado de Madera
Madera con TerminadoFinal
S3Switch deTres vías
CBCisterna sinfilos
Switch deDesconexión
ERV-1Ventilador de Exhausión de techo
2 1 0 2 4
Escala Gráfica
3 Hoja de Keynote
101
VESTIBULEIdentificador deHabitación
D2A-512
Indicador de Detalle 2
Indicador deReferencia de laRetícula
©2005. All rights reserved, including W
orld rights & Electronic rights. U
.S. copyright held by The Construction Specifications Institute. v07M
ar05a**TIPOS DE SÍMBOLOS
TIPOS DESÍMBOLOS
• Símbolos de Referencia
• Símbolos de Líneas
• Símbolos de Identidad
• Símbolos de Plantillas
• Símbolos de Materiales
• Símbolos de Texto
NCS: CSI’S UNIFORM DRAWING SYSTEM (UDS)
Puerta Izquierdade una solabisagra
Mesa Cuadradac/Sillas sin Brazos
FregaderoGeneral
Cubo de Regadera
©2005. All rights reserved, including W
orld rights & Electronic rights. U
.S. copyright held by The Construction Specifications Institute. v07M
ar05a
NUEVO en NCS 3.1:
• Los Símbolos ahora están organizados de acuerdo a MF2004
• Los Símbolos están Sub-Organizados por Tipo
**ORGANIZACIÓN DE SÍMBOLOS
ORGANIZACIÓNDE SÍMBOLOS
NCS: CSI’S UNIFORM DRAWING SYSTEM (UDS)
©2005. All rights reserved, including W
orld rights & Electronic rights. U
.S. copyright held by The Construction Specifications Institute. v07M
ar05a**ANOTACIONES: MÓDULO 07
MÓDULO 07
ANOTACIONES
NCS: CSI’S UNIFORM DRAWING SYSTEM (UDS)
©2005. All rights reserved, including W
orld rights & Electronic rights. U
.S. copyright held by The Construction Specifications Institute. v07M
ar05a
Temas:
• Clasificación de Anotaciones
• Uso de Notas
• Formato de Notas
• Terminología de Anotaciones
• EncandenandoNotas a Especificaciones
**REVISIÓN DE ANOTACIONES
MÓDULO 07
ANOTACIONES
NCS: CSI’S UNIFORM DRAWING SYSTEM (UDS)
©2005. All rights reserved, including W
orld rights & Electronic rights. U
.S. copyright held by The Construction Specifications Institute. v07M
ar05a
• Notas Generales
• Notas Generales[por Disciplina]
• Hoja de NotasGenerales
• Palabras Clave de Referencia
• Hojas deKeynotes
**TIPOS DE NOTAS
TIPOS DENOTAS
NCS: CSI’S UNIFORM DRAWING SYSTEM (UDS)
©2005. All rights reserved, including W
orld rights & Electronic rights. U
.S. copyright held by The Construction Specifications Institute. v07M
ar05a
• Aplican por Igual a Todas las Hojas en Un Conjunto de Dibujos
• No corresponde a una representación gráfica
• No están“encadenadas” con otros dibujos o especificaciones
• Se localizan en la disciplina G-, Tipos de hojas de dibujos Generales
**NOTAS GENERALES
NOTASGENERALES
“ABREVIATURAS: HAGA REFERENCIA A LA VERSIÓN 3.1 DEL U.S. National CAD Standard™”
Ejemplo:
NCS: CSI’S UNIFORM DRAWING SYSTEM (UDS)
©2005. All rights reserved, including W
orld rights & Electronic rights. U
.S. copyright held by The Construction Specifications Institute. v07M
ar05a
Se localizan dentro de las Notas Generales de la disciplina G-, Hojas Generales
**UBICACIÓN DE LAS NOTAS GENERALES
O - OPERATIONSZ - CONTRACTOR/SHOP DRAWINGSX - OTHER DISCIPLINESR - RESOURCET - TELECOMMUNICATIONSE - ELECTRICALM - MECHANICALD - PROCESSP - PLUMBINGF - FIRE PROTECTION
Q - EQUIPMENTI - INTERIORSA - ARCHITECTURALS - STRUCTURALL - LANDSCAPEC – CIVILW – CIVIL WORKSB – GEOTECHNICALV – SURVEY/MAPPINGH – HAZ MATERIALS
G - GENERAL
NCS: CSI’S UNIFORM DRAWING SYSTEM (UDS)
UBICACIÓNDE LASNOTAS
GENERALES
©2005. All rights reserved, including W
orld rights & Electronic rights. U
.S. copyright held by The Construction Specifications Institute. v07M
ar05a**FORMATO DE LAS NOTAS GENERALES
GENERAL SHEETNOTES
1. IIII II III III 2. II III II II 3. II IIIII II III4. I II IIII III I5. III I II IIII I
UBICACIÓNDE LASNOTAS
GENERALES
Ubicar las Notas Generales en la parte Superior del Block de Notas
NCS: CSI’S UNIFORM DRAWING SYSTEM (UDS)
“LA PARTE SUPERIOR DE LAS ELEVACIONES DEL ACERO ESTAN BASADAS EN LA ELEVACIÓN DEL PISO TERMINADO DE 100m –VEER LA HOJA C-101 PARA LOS DATOS ACTUALES Y LA INFORMACIÓN DE REFERENCIA.”
NOTA:
Si la disciplina no contiene el denominador del Tipode Hoja 0 (General), localícelas en la primera hoja de la disciplina
©2005. All rights reserved, including W
orld rights & Electronic rights. U
.S. copyright held by The Construction Specifications Institute. v07M
ar05a**UBICACIÓN DE NOTAS GENERALES [POR DISCIPLINA]
Ejemplo:
• Comunican información específica de la disciplina
• No corresponden a una representación gráfica
• ubicadas en el denominador del Tipo de Hoja 0 (General) de la clasificación de Tipos de Hojas
NOTASGENERALES[Disciplina]
E-301E-102E-101
E-001
A-301A-201
A-101
A-001
S-501S-302S-101S-001
NCS: CSI’S UNIFORM DRAWING SYSTEM (UDS)
©2005. All rights reserved, including W
orld rights & Electronic rights. U
.S. copyright held by The Construction Specifications Institute. v07M
ar05a**REVISIÓN DE NOTAS GENERALES POR DISCIPLINA
HOJA DENOTAS
GENERALES
• Aplican solo en una hoja
• No corresponden a una representación gráfica
• Comunican instrucciones específicas
• No están “encadenadas” con otras hojas/especificaciones
•Se localizan en cualquier hoja del proyecto
“DIMENSIONES DIBUJADAS EN LOS MUROS E DIVISIÓN SON A LA CARA DEL MONTANTE A MENOS QUE SE ESPECIFIQUE OTRA COSA”
Ejemplo:
NCS: CSI’S UNIFORM DRAWING SYSTEM (UDS)
©2005. All rights reserved, including W
orld rights & Electronic rights. U
.S. copyright held by The Construction Specifications Institute. v07M
ar05a**REVISIÓN DE KEYNOTES DE REFERENCIA
KEYNOTESDE
REFERENCIA
• Identifica & hace referencia a una representación gráfica en las Secciones de Especificaciones
• Localizada dentro del área gráfica & en el área de Notas del Block de Dibujo
• Conectada al gráfico por un Leader & un Identificador
NCS: CSI’S UNIFORM DRAWING SYSTEM (UDS)
Nuevo en el NCS versión 3.1:Las coordenadas de formato de la raíz con MasterFormat™ 2004
Modificador del Keynote de Referencia: Texto opcional localizado abajo del Keynote de Referencia, Aparece sólo en los Blocks de Dibujo
Punto Decimal - Separa la Raíz del sufijo
Sufijo: Definido por el Usuario, un sóloCaracter alfabético
Raíz: Usa el mismo Número de especificación que la referencia
03 20 00 . A01
©2005. All rights reserved, including W
orld rights & Electronic rights. U
.S. copyright held by The Construction Specifications Institute. v07M
ar05a**COMPONENTES DEL KEYNOTES DE REFERENCIA
Consta de:
• Raíz
• Punto Decimal• Sufijo
• Modificador del Sufijo
• Modificador del Keynote de Referencia
03200 . A01
Modificador del Sufijo – opcional,Definido por el Usuario, númerode dos dígitos
( #4 BARRAS 400mm OC)
NCS: CSI’S UNIFORM DRAWING SYSTEM (UDS)
KEYNOTESDE
REFERENCIA
©2005. All rights reserved, including W
orld rights & Electronic rights. U
.S. copyright held by The Construction Specifications Institute. v07M
ar05a**FORMATO DEL KEYNOTE DE REFERENCIA
REFERENCE KEYNOTES
DIVISION 03 - CONCRETE03 20 00.A REINFORCING STEEL03 20 00.B WELDED WIRE MESH03 30 00.A CAST-IN-PLACE CONCRETE
03 30 00.A03 20 00.B
03 20 00.A(#4 BARS)
Keynote deReferencia en elBlock de Dibujo
Keynote deReferencia en elBlock de Notas
NCS: CSI’S UNIFORM DRAWING SYSTEM (UDS)
KEYNOTESDE
REFERENCIA
©2005. All rights reserved, including W
orld rights & Electronic rights. U
.S. copyright held by The Construction Specifications Institute. v07M
ar05a**FORMATO DEL KEYNOTE DE REFERENCIA
REFERENCEKEYNOTES
1. IIIII.I III XX2. IIIII.I II II X3. IIIII.I I II IIII4. IIIII.I II IIIIII5. IIIII.I IIII IIIX
GENERAL SHEETNOTES
1. IIII II III III 2. II III II II 3. II IIIII II III4. I II IIII III I5. III I II IIII I
Localize el Keynote de Referencia Abajode las NotasGenerales
NCS: CSI’S UNIFORM DRAWING SYSTEM (UDS)
KEYNOTESDE
REFERENCIA
©2005. All rights reserved, including W
orld rights & Electronic rights. U
.S. copyright held by The Construction Specifications Institute. v07M
ar05a**REVISIÓN DEL KEYNOTE DE LA HOJA
KEYNOTESDE LA HOJA
• Identifica & hace referencia a uanrepresentación gráfica que NO esta encadenada a las secciones de especificaciones
• Se localiza dentro del gráfico & el Área de Notas del Block de Dibujo
• Está conectado al gráfico por un Leader & un símbolo hexagonal & un número
Keynotes de Hojaen el Block de Dibujo
Keynotes de Hojaen el Block de Notas
SHEET KEYNOTES2
1. DRENAJE PISO EXISTENTE
2.LA LINEA PUNTEADA INDICA LA PROYECCIÓNDE ARRIBA
NCS: CSI’S UNIFORM DRAWING SYSTEM (UDS)
©2005. All rights reserved, including W
orld rights & Electronic rights. U
.S. copyright held by The Construction Specifications Institute. v07M
ar05a**FORMATO DEL KEYNOTE DE HOJA
SHEETKEYNOTES
1.III III IIII II
2.III III II II
3. III II
GENERAL SHEETNOTES
1. IIII II III III 2. II III II II 3. II IIIII II III4. I II IIII III I5. III I II IIII I
REFERENCEKEYNOTES
1. IIIII.I III XX2. IIIII.I II II X3. IIIII.I I II IIII4. IIIII.I II IIIIII5. IIIII.I IIII IIIX
Localizar el Keynotede Hoja Abajo del Keynote de Referencia
NCS: CSI’S UNIFORM DRAWING SYSTEM (UDS)
KEYNOTESDE LA HOJA
©2005. All rights reserved, including W
orld rights & Electronic rights. U
.S. copyright held by The Construction Specifications Institute. v07M
ar05a**REGLAS DE LAS NOTAS GENERALES
REGLASGENERALES
En lugar de:
“LADRILLO ROJO DE LACOMPAÑÍA ACME, INC.”
Use:
“LADRILLO RECTO”
Use un lenguaje genérico y conciso
XX14.97 14.97
09 65 00.G GYPSUM BOARD
09 65 00.G GYPSUM BOARD
Use Fuentes Tipográficas en Mayúsculas, Sans serif, Proporcionales,No-estilizadas
X
NCS: CSI’S UNIFORM DRAWING SYSTEM (UDS)
©2005. All rights reserved, including W
orld rights & Electronic rights. U
.S. copyright held by The Construction Specifications Institute. v07M
ar05a**ACUERDOS DE CÓDIGO: MÓDULO 08
MÓDULO 08
ACUERDOS DE CÓDIGO
NCS: CSI’S UNIFORM DRAWING SYSTEM (UDS)
©2005. All rights reserved, including W
orld rights & Electronic rights. U
.S. copyright held by The Construction Specifications Institute. v07M
ar05a**REVISIÓN DE ACUERDOS DE CÓDIGO
• Acuerdos gráficos para incorporar dibujos sobre documentos de construcción
• Permite rapidez/facilidad
• Código de búsqueda rápida
• Identifica información para documentos de construcción
• Identifa la ubicación de la información de regulación
NCS: CSI’S UNIFORM DRAWING SYSTEM (UDS)
MÓDULO 08©
2005. All rights reserved, including World rights &
Electronic rights. U.S. copyright held by The C
onstruction Specifications Institute. v07Mar05a**
REVISIÓN DE ACUERDOS DE CÓDIGO
• Se usa como un Checklist durante el Diseño/Revisión
• Asiste en al actualización, rastreo, e implementación de decisiones de codificación
• Herramienta que proporciona instrucción
• Herramienta de Administración de Instalaciones durante la renovación, la remodelación o el agregado a un proyecto
NCS: CSI’S UNIFORM DRAWING SYSTEM (UDS)
MÓDULO 08
©2005. All rights reserved, including W
orld rights & Electronic rights. U
.S. copyright held by The Construction Specifications Institute. v07M
ar05a**ACUERDOS DE REGULACIÓN
ACUERDOSDE
REGULACIÓN
• Tablas para cada identificador de categoría:
• Regula la información a incluir en el dibujo
• Ubicación (de acuerdo al Módulo 01)
• Formato de presentación (Texto y/o gráficas)
La Información Relacionada a la Determinación de Acuerdos de Regulación se Agrupan en 12 Categorías:
11 – Mechanical
12 – Electrical
10 – Plumbing
9 – Fire Protection-Active
8 – Structural
7 – Energy
6 – Accessibility
5 – Fire Protection-Passive
4 – Life Safety-Egress
3 – Building
2 – Site
1 – General
NCS: CSI’S UNIFORM DRAWING SYSTEM (UDS)
©2005. All rights reserved, including W
orld rights & Electronic rights. U
.S. copyright held by The Construction Specifications Institute. v07M
ar05a**EJEMPLO DE ACUERDOS DE REGULACIÓN
EJEMPLO
Nivel 1 Nivel 2
2 - Site Site-Related Design CriteriaLocation on site (distances to lot lines/existing buildings) C-1XX CS-1XX GraphicSite grading/water run-off C-1XX CG-1XX GraphicIrrigation L-1xx LI-1XX GraphicErosion control details C-5XX CG-5XX GraphicEnvironmental impact statements PM PM TextZoning drawings G-0XX GI-0XX Text
CategoríaGrupo Información Regulatoria
Drawing LocationFormatoSugerido
NCS: CSI’S UNIFORM DRAWING SYSTEM (UDS)
©2005. All rights reserved, including W
orld rights & Electronic rights. U
.S. copyright held by The Construction Specifications Institute. v07M
ar05a**EJEMPLO DE ACUERDOS DE REGULACIÓN
EJEMPLOGRÁFICO
Plano Llave Area Incendio
LEYENDA1 HORA2 HORA3 HORA4 HORA
1 HORA 2 HORA
0 HORA ROOF/CLG
AR
EA IN
CEN
DIO
“B
”A
REA
INC
END
IO “
A”
UN EDIFICIO MIXTO DEALMACENAMIENTOY VIVIENDA
AREAINCENDIO“C”
NCS: CSI’S UNIFORM DRAWING SYSTEM (UDS)
©2005. All rights reserved, including W
orld rights & Electronic rights. U
.S. copyright held by The Construction Specifications Institute. v07M
ar05a
NCS: TRI-SERVICES PLOTTING GUIDELINES**
LINEAMIENTOS DE PLOTEO TRI-SERVICES
LINEAMIENTOSDE
PLOTEOTRI-SERVICES
©2005. All rights reserved, including W
orld rights & Electronic rights. U
.S. copyright held by The Construction Specifications Institute. v07M
ar05a**LINEAMIENTOS DE PLOTEO PRINCIPIOS GENERALES
• Permite la impresión consistente en blanco & negro desde archivos a color
• Mapeo consistente del color
• Permite a los fabricantes de productos de CAD desarrollar Mapeos de color
NCS: TRI-SERVICES PLOTTING GUIDELINES
LINEAMIENTOSDE
PLOTEO
©2005. All rights reserved, including W
orld rights & Electronic rights. U
.S. copyright held by The Construction Specifications Institute. v07M
ar05a
NCS Color #
Pen Plotter
Pen mm
Laser/Elec InkJet in. Plot Color MicroStation
Color #MicroStation line weight
AutoCad Color #
1 0.18 0.007 Black 3 0 12 0.25 0.010 Black 4 1 23 0.35 0.014 Black 2 2 34 0.35 0.014 Black 7 2 45 0.50 0.020 Black 1 3 56 1.00 0.039 Black 5 7 67 1.40 0.055 Black 0 10 78 0.35 0.014 Halftone 9 2 89 2.00 0.079 Black 14 15 9
10 0.18 0.007 Black 10 0 1011 0.25 0.010 Black 19 1 1112 0.35 0.014 Black 27 2 1213 0.50 0.020 Black 35 3 1314 0.70 0.028 Black 43 5 1415 1.00 0.039 Black 51 7 15
**EJEMPLO DE LINEAMIENTOS DE PLOTEO
LINEAMIENTOSDE
PLOTEOEJEMPLO
NCS: TRI-SERVICES PLOTTING GUIDELINES
©2005. All rights reserved, including W
orld rights & Electronic rights. U
.S. copyright held by The Construction Specifications Institute. v07M
ar05a
Preguntas&
Respuestas
Recommended