BEX100 – Basic Electricity Semiconductors Transistors & SCR’s

BEX100 – Basic Electricity

Semiconductors

Transistors & SCR’s

Lesson Objectives• To understand the basic construction elements and

schematic symbols of a transistor• Be able to identify the two main types of

transistors, (PNP, NPN types) and explain how they operate

• Understand what is meant by “Amplifier Current Gain” of a transistor

• Interpret wiring schematics containing transistors• Identify the various application uses for transistors• Understand the basic construction of an SCR and

how it functions

Introduction to Transistors

• A transistor is an electrical device that is used to control current flow

• It is made of three layers of semiconductor material• The construction is similar to the diode• Transistors often take the place of mechanical

switches and relays• A transistor can be thought of as two diodes that

share a common center layer

Introduction to Transistors

The terms used for the 3 terminals of a transistor are: “the emitter”, “the collector”, and “the base”

Introduction to Transistors

• The common schematic symbols used for transistors

• The “emitter” always has a line with the arrow

• The “base” is the heavy line at the bottom of the symbol

• The “collector” is the line without the arrow

Transistor Construction• Adding a second layer of “P-type” material to the basic

diode construction creates a “PNP” transistor

• Adding a second layer of “N-type” material to the basic diode construction creates a “NPN” transistor

Basic Transistor OperationSupplying a positive/negative voltage to the base

supplies the electrons needed for current flow

Transistor Operation“Amplification” aspects of a transistor

Amplifier Current GainTransistors are small electrical controls that can perform large electrical tasks. “Saturation” level occurs when the

maximum current flow of the circuit is reached.

The “NPN” Transistor

“NPN” Transistor Operation

• Supplying a small amount of current to the base creates current flow through the transistor (switched on)

• Varying the amount of current supplied to the base varies its resistance and can vary the current flow through the emitter-collector

• No current to base means no current will flow (switched off)

A Typical “NPN” Circuit

The “PNP” Transistor

“PNP” Transistor Operation

• Operates the same as the NPN type of transistor

• One difference being the bias of the transistor in the circuit

• Another being the polarity of the voltage in the circuit

• Has the same amplification ability as the NPN

• Operates as a electrical switch in the circuit

A Typical “PNP” Circuit

Transistor Applications

The Darlington Pair• Used when the current level supplied at the base is too

small to allow sufficient current flow through the circuit

• The first transistor is used to supply the necessary current to the base of the second transistor which controls the circuit

Solid State Relays• Used in situations where a “relay-type” circuit is needed

• A “NPN” type transistor controls a “PNP” type transistor

• Benefits of solid state relays include faster operation, and there are no moving parts to wear out

HEI Transistorized Ignition System

EST Electronic Spark Timing

The Hall Effect Switch

The Hall Effect Switch• With vanes “open” current flows to transistor

• HEI reference voltage is less than 1 volt

• With vanes “closed” no current flows to transistor

• HEI reference voltage is 12 volts

SCR Silicon Controlled Rectifiers

SCR Silicon Controlled Rectifiers

“SCR” Silicon Controlled Rectifiers are a type of transistor that by nature do not allow current to

flow in either direction until triggered

Unlike the transistors that act as switches, the SCR will continue to conduct current even after the

trigger voltage has been removed

The main source of voltage must be removed from the circuit to stop current flow through the SCR

The Silicon Controlled Rectifier

• Schematic symbol is similar to diode

• “The Anode” is positive

• “The Cathode” is negative

• “The Gate” is the trigger

• A momentary voltage is all that is required to initiate and maintain current flow

SCR Operation

SCR Construction & Operation

• Constructed with alternating layers of semiconductor material

• Similar to combining a PNP and a NPN type transistor

• Functions by applying voltage to the “gate” terminal

LET’S REVIEW

• WHAT ARE THE THREE LAYERS OF A TRANSISTOR?

• WHAT IS THE SCHEMATIC SYMBOL FOR A TRANSISTOR?

• WHAT ARE TWO FUNCTIONS OF TRANSISTORS?

• WHAT ARE TWO THINGS THAT WILL DAMAGE A TRANSISTOR?

Elizabethtown Technical CollegeBEX100 – Basic Electricity

TransistorsSpring Semester 2001