Battery Watering Technologies

Battery Watering Technologies

• And now introducing…

The Centurion Valves!

•Low profile design.

•Reinforced barbs eliminate the need for clamps.

•Push in style valve for easy installation and removal.

•All working parts are above the cell.

Centurion Valve

•Indicator eye visible from top and side.

•Angled barbs to help navigate around connectors.

•Solid polypropylene float.

•No more flip top lid.

•Ample spacing between the float and encapsulation.

Centurion Valve

Widest Pressure Range in the

Business.

Centurion Valve

Solid Polypropylene float

Won’t allow Electrolyte to leach Into the float

Technology

Part #: DF72G (Direct Fill Gun)

Part # NT2000G (5 gallon gravity tank) Part #: NT2212GF (2.5 gallon gravity tank)

Part #: NC5080P (8 gallon aqua sub) Part #: NC5250P (25 gallon push cart)

Part #: PW-1800 Deionizer

Superior Warranty

We offer a full five year warranty that covers all aspects of a failure.

If the cell fails due to a defect in our product, we pay for the repair!

MADE IN THE USA!

Manufactured in the USA

Manufacturing

• We Control the Process.

• Better Products.

• Superior Manufacturing.

• Highest Quality Standards.

State of the art ISO 9000 certified Manufacturing Facility

ISO/TS 16949 Approved 2010 ISO14001 Approved 2010

•170 Employees• 24 Hour Operation• 85 To 1000 Ton Injection Molding Machines• Ford Tier 1 Supplier• Chrysler Tier 1 Supplier• GM Tier 1 Supplier• Mercedes Approved Source

Diversified

Filling pressure:

•When using a BWT Direct Fill Gun/Link: 20-100 PSI

•Recommended fill pressures (into quick connect) 2-25 PSI. Up to 35 PSI can be used if recommendations below are followed. Recommendations:

•Avoid pulsating water supply (pump rapidly cycling on and off)•Always remove air from the line before filling

Product Update

Filling outside of recommended pressure:

•If below 2 PSI: Valves will continue to perform but filling time increases.

•If above 25 PSI: Filling time will be reduced. It is possible that the final valve/cell to complete filling may close prematurely.

Product Update

Filling Flow Rate Chart: 

Filling Flow Rate

0.20

0.30

0.40

0.50

0.60

0.70

0.80

0.90

1.00

0 2 4 6 8 10 12 14 16 18 20

PSI

BWT Valve flowl/min

Single valve filling flow rate vs. fill pressure

• Valve String flow rate:

Total flow rate depends on number of valves in string, Filling pressure and connection method.

Typically 2-3 gallons/Minute at 20 PSI.

Many different delivery options can be utilized.

Filling Flow Rate

Manufacturing is ISO-9001, ISO/TS-16949 certified.

• Each component part has a specific molding specification and testing procedure used during manufacture.

• Each valve tested for shutoff, flow and mechanical freedom during the assembly process.

•Sampling and water testing performed on each box of valves at manufacturing. • Incoming sampling and testing done on each box at BWT. Inventory is in quarantine until released by QC. • Valves visually inspected during kit assembly.

Quality Control

Spark Propagation/Spark Arresting

All valves have built in water trap (P Trap) to avoid cell-to-cell vapor transfer/Spark propagation.

Valves for electric vehicles have spark arrestor to avoid external spark from involving cell.

Technology

Technology

Technology

Technology

Technology

BWT carries a five million dollar product liability policy.

Other Required Documents?

Indemnification

• The Highest Quality Products

• Exceptional, personal customer service

• Unmatched Support

• Five Year Cell Replacement Warranty

• Private Label Options

Thank You

Great Customers, Great Partners