View
10
Download
0
Category
Preview:
Citation preview
1
Automatic Double sided
Labeling Machine Model: IMC-650G
Operating instruction
2
Catalogue 1. Operating interface 3
2. Installation and Commissioning 7
3. Methods to adjusting photoelectric switch 13
4. Fault Solution 14
5. Routine maintenance and announcements 15
6. Dynamic power operating requirement 16
7. Label circle direction diagram 16
8. Circuit diagram 17
9. Sensor settings 18
3
1. Operating interface
Connect the power, turn on the mail power switch, enter into Startup Screen as follow
Chart 1
In chart 1,there are our company name and contact information. If the machine goes
wrong, you can contact in time through this and remove the problem to ensure production
smoothly. In this screen, press ENGLISH into the English interface. In this screen, press
button“ " to select double sides labeling system, the system will enter into the
main screen shown in Chart 2: (Chinese interface)
4
Chart 2 Illustration of each button as follows
1.Press" LOAD" button ,the system will enter into the following interface, as chart 3:
Chart 3
Enter the application number which need open, press "ok" can call out the parameters
which be stored in the machine to avoid duplication of input parameters. And Improve
production efficiency. six groups of applications can be called, if no need call the
parameters, press the button "Exit" to exit the interface, the system will not load this
group parameters; 2.Press"save"button ,the system will enter into the following interface, as chart 4
5
chart 4
Enter into save application number witch need save and application name. press "ok" It
can save the parameters in the machine, to facility the same production after calling out to
avoid duplication of input parameters, improve production efficiency. It can save six
groups of application program, if no need save the parameters, please press "Exit" button
and exit the interface, the system will not save this group parameters; Note: if after press
"OK" button save ,parameters of previously stored application number will be covered.
3."JOG" press this button ,the machine will run according to the set up parameters,
loosen the button, the machine will stop, The button is fairly practical when debugging the
machine, by means of press and loosen the button's time to make the machine stop where
you need to stop, It is convenient to check the commissioning effect of the machine.
4. : This line for option of machine speed, the selected color become red. It can
select the best speed according to different products.
5."RUN" button for run/stop, press it ,machine will run according to setting parameters;
6
Meanwhile, the button change to "STOP". When running ,press it ,the machine will stop
running immediately, at the same time the button will become "RUN".
6."Exit":press the button machine will return to the starting up menu as Chart 1
7. "stopping" the position is called information display. In this column shows the status of the machine. According to the information in the column to process the equipment
problem, machine fault handing details(4、Fault solution)
8."Parameters set up ": press the button , the machine enter into parameters set up menu
as chart 5
chart 5
In this screen, the define of each parameter as following;(Remarks: left part for front label
parameter, right part for back label parameter)
A、 Label speed: Label inlet speed. Input by touching parameter area. Number
range:0-30m/min;
B、 Label offset : position of label stop. Input by touching parameter area. Number
range:0-200m/min
C、 Label delay: Starting to delivery the label After electric eye of checking object
detect objects, delay setting time to ensure that the label is posted to the specified
place. input through parameter area , numerical range :0-1000ms
7
D、 Press "TEST" button, label sending device will feed one label, accordingly, it can
set up the feed label parameters. When "label head open "show "label head close",
the label sending device will stop feed the label, when "label head open" show
"label head open", press "test", the label sending device will feed one
label, accordingly adjust the feed label parameters;
E、 "RUN JOG": The function same as chart 2
F、 "EXIT" press this button will exit the menu, return to main screen(chart2)
G、 "set up:099999 output:000000" "set up" for product amount set up this time,"
output" for this actual production amount, input by touching parameter
area, range : 0-999999,when the project output value exceeds the actual
production settings, the system will stop run, while prompt "product counter
overflow" ,at this time need to re-set the count;
2.Installation and Commissioning Place the machine stable on the floor , adjust the feet, make sure the machine is in a
horizontal position, start to adjust each part of machine
1、 Conveyor adjust( normally it have been adjusted before out of factory, no need to adjust if without demolition )
Adjustable nut 1 can adjust the intensity of conveyor, both sides of conveyor need
balancing
Lock nut1
8
Place the machine stable on the floor , start to adjust the machine according to steps as
following:
Press belt part construction as diagram
setting nut
。
Adjustment to Press belt tightness : the above setting nut can adjust to tightness level
of press belt ,it has been adjusted before out of factory, it need not to
adjust without take apart ,When using for a while, the length of belt has
change or need to change, it need adjust "setting nut" to adjust the
tightness of belt.
Adjustment to the height of belt: Place the product on the conveyor, rotate belt setting
handle, make white belt press to the product 3mm more or less (it
depends), as following picture
setting handle
9
Centering unit construction as picture
Handle1 Nut1 Handle2
Tightness adjustment: adjust reshaping belt nut 1, to make tightness suitable;
Adjustment steps:
1、Place the product to the right underneath of the white belt ( if the width of shaping belt is
not enough ,turn the horizontal setting handle 1,make the withe chain not touch th
product);
2、Rotating vertical setting handle 2 of shaping belt, so that the height of the white chain
under middle of the product, height of shaping belt need be consistent;
3、Rotating horizontal setting handle 1, so that the white chain clip the product at the same
time, also make the product appear little variant ( Provided that the products can
smoothly enter the plastic zone
Adjustment to checking optical head detect the distance angle
Choose one slowest conveyor speed in the human computer interface ,let product run
to near optical head, Makes the fiber head perpendicular to product posted veneer,
and keep the maximum distance 2-3mm
Adjustment to the distance between labeling head peeling board and product
Press "Jog conveyor line," the product stopped in the vicinity of Peel board, through
the adjustment of the labeling head 8-dimensional space, making the peel plate edge
10
parallel with the product and have a distance about 2mm (angle adjustment
according to the radian size of the bottle to adjust)
Step 5:Adjust the width of guard bar and bottle separation wheel
Both of front and back of the conveyor belt, there are guard bars that can be adjusted
according to bottle size. Adjustment methods : first, loosen the top locked nut. Guard
bar can move front and back, adjusting the distance of both sides of guard bar to same
width of bottle; loosen the locked nut 2,move guard bar up and down. It's the right
height for the bottle in the conveyor line that will not run dump. after adjusting the
position, then lock the locking nut.
Lock nut1 Lock nut2
Bottle separation wheels as picture
Handle Turn the double sides of handle, make the sponge wheel press bottle tightly, turn on
bottle separation wheel switch ,launch conveyor, observe the running state of bottle
on the conveyor ,through governor adjust bottle separation wheel rotate speed, let the
11
distance between two bottles is Moderate
Step 6 :accurately wind the label well , press the front and back rollers, then start to adjust
the each part of labeling head .
label outlet adjustment
a、Adjustment to label detect the place of photoelectric switch.
Lock nut 1 Loose lock nut 1 as above picture, adjust the place of label photoelectric switch, make the label pass the detection area of label photoelectric switch a. Label delivery tension adjustment
Nut1 Nut2
12
Press "label sending device" on the control panel, and observe whether the label edge is parallel with the edge of the label board, if the distance between upper edge and the edge of label board is bigger than the distance between down edge and label board, then press nut 1 tightly more or loose nut 2 more; on the contrary, the opposite adjustment can be used, also by watching whether the height of both sides of base paper between delivery paper and return paper is parallel to judge if delivery label is parallel.
b. Offset adjustment
Label plate
Label1
Press "label sending device test" button, feed one label ,see the length of label
offset, according to the length ,increase or decrease the offset size on the
operation board, till the label just offset the label board( In generally, the length of
label offset peeling board is about 2mm more or less, different material label have
different offset length)
13
c. Adjustment to tilt angle of label offset
Slider bar2 Slider bar1
In order to make label edge be parallel with attaching veneer, adjust the tilt angle of
vertical and horizontal of offset board. Turn the slider 1 can increase or decrease the
vertical tilt angle of the board to ensure that when the label offset ,it is parallel to the
posted surface; rotate slider 2, To adjust horizontal tilt angle of board, to ensure that
the label edges parallel to the bottle edge .
d. Adjustment to up and down of labeling head
Handle1
Press "RUN", try to post one bottle ,observe if the up and down place of bottle is
suitable ,if move up or down, turn the handle 1, make the whole label sending
device go up or go down, to ensure the distance of label up and down suitable,
then lock fixed nut.
h. Scraper accommodation
After the label posted to the bottle ,it is not tightly completely posted to the bottle,
need use the scrapper to scrap smoothly. scrapper institution as picture
14
Nut3
Axle2 Handle screw1
Loosen the adjustable handle screw1, scraper can turn around the axis 2,It can
adjust the compression level of the scraper by adjusting the angle ; loosen the nut
3, the scraper can be elastic . After the label is slick by the scraper , in order to
improve the quality of labeling, the need to compress twice by the sponge,
non-powered compressed sponge institution as picture
handle1
Turning handle 1, Put the bottle clip in the middle of conveyor belt, after finishing the
labeling, ensuring the label goes through sponge again, Labeling effect is better.
15
3、Adjustable methods of Photoelectric switch
(1) (Keyence FS-V11) Electric eye of checking object
D.ON L.ON
MODE
SET
数值显示器黄色指示灯红色指示灯
光纤锁
Electric eye of checking object diagram
a、When using single optic, it should use fall delay ,the switch dial to "D.on"
b、 Press “!” or “"”number of display will coruscate, this number called
median(the number is between watching product and non-watching
product),repress “!” or “"” that can increase or decrease the value, the value is
larger ,the sensitivity of electric eye is weaker ,the value is smaller ,the sensitivity
of electric eye is stronger;
c、When the product color is transparent, red, black etc. The value is small as you
can ,when using correlation optic, it should be used "rise delay" that switch to "L.
ON" side, the median transferred to a row of yellow lights are just not bright;
16
(2 )(Leuze GK14/24) Electric eye of Label
Label electric eye diagram
a. In the absence of labels or body paper, rotate the standard adjusting knob, that make the luminance of standard adjusting indicator lights accordance;
b. In label area, rotate sensitivity adjusting knob that make the luminance of
standard adjusting indicator lights accordance
c. Label outlet test to observe whether there are exceptions, if a label finishing need several times, it indicates that sensitivity is strong, Turn counterclockwise sensitivity adjustment knob , until the test one time one label , if test once, the label will be a few , then the sensitivity is weak, turn the sensitivity adjustment knob clockwise until the time just out of one label
Benchmarkcontrol indicator
sensitivity control indicator
Benchmark control Knob
sensitivity controlKnob
17
4、Fault solutions The status bar in the main interface will display the system state
To display the current state of the system or the occurred fault information, the
common faults as follows
Label delivery device without label: No label through label detection photoelectric
switch or photoelectric switch cant detect label.
Solutions:
1) If there are no label pass the photoelectric switch, let the label which on the part of
base paper pass photoelectric switch.
2) If the photoelectric switch cant detect the label, please press three.2 to adjust its
place, till it can detect the label;
3) If you still can not detect the position after adjusting the position, you need press
four(second) to adjust the sensitivity according to the photoelectric switch ;
4) If it still can not solve the problem after going through the above steps , maybe the
label has the following problem: a. . label without gap or the gap is too small; b.
Irregular shape or varied thickness . Please change another photoelectric switch
LRD6100, can solve the problem.
2. Production counter spill: action of production counter, actual output already
bigger than scheduled production. Solution: reset up the counter.
3. Servo motor alarm: Servo drive failure. (Turn off the power to re-start, or change
the driver)
18
5、Routine maintenance and precautions 1、Check the tightness of chain board of conveyor belt , adjust the rating nut of
transmission line to adjust the tightness of chain board
2、Check the brake spring of labeling head if it damage or break off per week, if
so ,please change the spring in time.
3、The Fiber cant be bent and touch the pasted objects
4、Prohibit using hard objects such as screwdrivers, wrenches etc. to touch the touch
screen to prevent scratching it.
5、Photoelectric switch can only be responsible for the equipment by the regulation to
prohibit non-responsible staff adjustment, adjustment disorder to prevent optical
switch.
6、After installing the label ,please pay attention to the directions of collection paper
roll, to prevent label clamp.
7、All the motor plug and plug connectors which are in charge can not pull out , you
must operate in case of power failure
6. Power using requirements and power parameters
Voltage using requirement: Single phase 220V 50Hz AC voltage
Switch control requirement: Single phase 20A Leakage switch
Leakage current 30mA-100mA
Power of the machine: 3000W
19
7、Label circle drawing Left labeling head(Red line is label)
Right labeling head(Red line is label)
20
8、circuit diagram
!"#$%&%%&"%&'%&(%&)%&*&!#$
"!%&%%&"%&'%&('!%&)%&*%&+%&,!#$
%-
')- %-
')-
PORT0
Q0
I
SOR1
./0!01.2.,3'''
0V
DC24V
SOR2
SOR1:Electric
eye of tested
bottle
SOR2:Left label
electric eye
!"#$%&'()*&(
%+$&%),-'.+/0),&
123'),4#5'"#54#5'/)6/#)5
DC
27293318
98
DC24V0V
!"#$%&%%&"%&'%&(%&)%&*&!#$
"!%&%%&"%&'%&('!%&)%&*%&+%&,!#$
PORT0
Q0
I./0!01.2.,3'''
DC
SOR5:Right label
electric eye
SOR5
SOR1
26273028
2629
3333
39
37363534
39
789:;<=
21
L
!"
#
$%
&'
(')
!"
#
STF
STR
RH
RM
RL
SD
To 0V
To PLC
$%
&*
$(+
,&-
V+
V-
()
DC24V
0V
./0123456/78
L+
M24V0V
13 8
EMG:Emergency stop switch
FUSE1
FUSE2 3A
FUSE6
!"#$%&'$()'*%&#)&+#(
$%
$%$%
SW
SW:Universal selector
M1:Left servo motor
M2:Right servo motor
M3:Main conveyor motor
To PLC
10To PLC
11To PLC
12
N
.78964:80978
EMG
KM
KM
K1 21
8 7
65
43
&;
FUSE5
$%
CAP
L1
L3
!"
#
STF
STRRH
RM
RL
SD
To 0V
To PLC
$%
&<
13 8
737475
$%
To PLC
10To PLC
11To PLC
12
FUSE3
FUSE4
L2
M4:Shapping belt motor
M6:Separate bottle wheel motor
L
!"
#
$%
&=
66
59
FUSE2
N
12
34
56
710
11
12
13 9
8141516
171819
202122
,'+-*.%/#0./
*"-.*#$1%2"&3#$.
Speed governor
>87?@7A2B
26A978178
.78964:80978
456789:
INDUSTRIAL SENSORS CATALOG www.sickusa.com 7028071 - © 2008 SICK, Inc. 936
IR
0.08…4.7 in (2…120 mm)
sensing range/fork width
Highlights
Dimensional drawing
Order information
Adjustments
dimensions in mm
Fork Sensors
WF Next
Fork depth 40 mm
WF Next, Manual
• Simple and accurate adjustment via“+” and “-” buttons
• PNP and NPN switching output
• Selectable light/dark switching
• Rugged aluminum housing
510
9
7
B
811
6
10
A
19
C
3
2
2
1
– 3s
– 6s
+–
43
5
A (mm) B (mm) C (mm)Fork width Fork depth
WF2 2 42/59/95 14WF5 5 42/59/95 14WF15 15 42/59/95 27WF30 30 42/59/95 42WF50 50 42/59/95 40WF80 80 42/59/95 70WF120 120 42/59/95 110
3
5
4
All types
Optical axisMounting holes, Ø 4.2 mm Function indicator (red)Function indicator (yellow), switching output“+”/”-” buttons and function button5
4321
Type Part no.WF2-40B410 6028428WF5-40B410WF15-40B410WF30-40B410WF50-40B410WF80-40B410
60284306028431602843260284336028435WF120-40B410
6028429
1
2
2
Order information
Order informationFork depth 60 mmType Part no.WF2-60B410 6028436WF5-60B410WF15-60B410WF30-60B410WF50-60B410WF80-60B410
60284386028439602844060284416028442WF120-60B410
6028437
Order informationFork depth 95 mmType Part no.WF2-95B410 6028443WF5-95B410WF15-95B410WF30-95B410WF50-95B410WF80-95B410
60284456 028 4456028446602844760284486028449WF120-95B410
6028444
Dimensions
Accessories pageCables and connectors 1180
7028071 - © 2008 SICK, Inc. www.sickusa.com INDUSTRIAL SENSORS CATALOG 937
DC 12...30VQN - NPN outputQP - PNP outputblack
whitebrown
wire colors refer to standard cable, not included
12
0Vblue34
loadload
Technical data
Connection diagram
Technical data WF-
1) XX = Fork depth(e.g. 40 = fork depth equivalent to 40 mm)
2) Limit values, reverse polarity protected3) Without load
4) May not exceed or fall short of VS tolerances
5) Signal transit time with resistive load 6) With light/dark ratio 1:1; no time delay
7) Reference voltage 50 V DC8) A = VS connections reverse-polarity
protectedB = Outputs short-circuit protectedC = Interference pulse suppression
9) Do not bend when temperature isbelow -32° F (0° C)
10) Depending on fork width
Sensing range/fork width 0.1 in (2 mm)0.2 in (5 mm)0.6 in (15 mm)1.2 in (30 mm)2.0 in (50 mm)3.2 in (80 mm)4.7 in (120 mm)
Fork depth 40, 60, or 95 mmLight source LED, infrared light, pulsedMinimum detectable object size 0.008 in (0.2 mm)Supply voltage VS 10. . .30 V DC
2)
Current consumption3) 40 mAResidual ripple4) < 10%Switching output PNP/NPN
Light/dark adjustable via buttonSignal voltage
PNP HIGH = VS – (< 2 V)/LOW = 0 VNPN HIGH = VS/LOW = < 2 V
Output current IA 100 mAStability of response time5) ± 20 µsResponse time5), switching frequency6) Max. 100 µs; 10,000/sInitialization time 100 msAmbient light safety
Incandescent lamp 5,000 LuxSunlight 10,000 Lux
VDE protection class7) IIIEnclosure rating IP 65Circuit protection8) A, B, CAmbient temperature9) Operation -4…140° F (-20…60° C)
Storage -22…176° F (-30…80° C)Housing AluminumWeight Approx. 1.26…5.6 oz (36…160 g)10)
2-XX1)B410
5-XX1)B410
15-XX1)B410
30-XX1)B410
50-XX1)B410
80-XX1)B410
120-XX1)B410
Switching type: Light switching ( Q) Dark switching (Q–)Light path free Yes No Yes NoPNP/NPN output HIGH LOW LOW HIGHFunction indicator (yellow) On Off Off On
Output function
M8 Connector
3 1
4 2
INDUSTRIAL SENSORS CATALOG www.sickusa.com 7028071 - © 2008 SICK, Inc. 938
HighlightsFork Sensors
WF Next Dimensional drawing
WF Next, Teach-In
0.08…4.7 in (2…120 mm)
sensing range
• Simple setup using two-point teach-in
• PNP and NPN switching output
• Selectable light/dark switching
• Rugged aluminum housing
dimensions in mm
Order informationFork depth 40 mmType Part no.WF2-40B416 6028450WF5-40B416WF15-40B416WF30-40B416WF50-40B416WF80-40B416
60284526028453602845460284556028456WF120-40B416
6028451
Order information
Order informationFork depth 60 mmType Part no.WF2-60B416 6028457WF5-60B416WF15-60B416WF30-60B416WF50-60B416WF80-60B416
6028459
6028460602846160284626028463WF120-60B416
6028458
Order informationFork depth 95 mmType Part no.WF2-95B416 6028464WF5-95B416WF15-95B416WF30-95B416WF50-95B416WF80-95B416
60284666 028 4456028467602846860284696028470WF120-95B416
6028465
Adjustments
510
9
7
B
811
6
10
A
19
C
3
2
2
1
– 1s TII1s TI–
– 3s
– 6s
+–
43
5
A (mm) B (mm) C (mm)Fork width Fork depth
WF2 2 42/59/95 14WF5 5 42/59/95 14WF15 15 42/59/95 27WF30 30 42/59/95 42WF50 50 42/59/95 40WF80 80 42/59/95 70WF120 120 42/59/95 110
3
5
4
All types
Optical axisMounting holes, Ø 4.2 mm Function indicator (red)Function indicator (yellow), switching output“+”/”-” buttons and function button5
4321
IR
1
2
2
Dimensions
Accessories pageCables and connectors 1180
7028071 - © 2008 SICK, Inc. www.sickusa.com INDUSTRIAL SENSORS CATALOG 939
Technical dataTechnical data WF-
1) XX = Fork depth(e.g. 40 = fork depth equivalent to 40 mm)
2) Limit values, reverse polarity protected3) Without load
4) May not exceed or fall short of VS tolerances
5) Signal transit time with resistive load 6) With light/dark ratio 1:1; no time delay
7) Reference voltage 50 V DC8) A = VS connections reverse-polarity
protectedB = Outputs short-circuit protectedC = Interference pulse suppression
9) Do not bend when temperature isbelow -32° F (0° C)
10) Depending on fork width
Sensing range/fork width 0.1 in (2 mm)0.2 in (5 mm)0.6 in (15 mm)1.2 in (30 mm)2.0 in (50 mm)3.2 in (80 mm)4.7 in (120 mm)
Fork depth 40, 60, or 95 mmLight source LED, infrared modulatedMinimum detectable object size 0.008 in (0.2 mm)Supply voltage VS 10. . .30 V DC
2)
Current consumption3) 40 mAResidual ripple4) < 10%Switching output PNP/NPN
Light/dark adjustable via buttonSignal voltage
PNP HIGH = VS – (< 2 V)/LOW = 0 VNPN HIGH = VS/LOW = < 2 V
Output current 100 mAStability of response time5) ± 20 µsResponse time5), switching frequency6) Max. 100 µs; 10,000/sTeach-in via buttonInitialization time 100 msAmbient light safety
Incandescent lamp 5,000 LuxSunlight 10,000 Lux
VDE protection class7) IIIEnclosure rating IP 65Circuit protection8) A, B, CAmbient temperature9) Operation -4…140° F (-20…60° C)
Storage -22…176° F (-30…80° C)Housing AluminumWeight Approx. 1.26…5.6 oz (36…160 g)10)
2-XX1)B416
5-XX1)B416
15-XX1)B416
30-XX1)B416
50-XX1)B416
80-XX1)B416
120-XX1)B416
Switching type: Light switching ( Q) Dark switching (Q–)Light path free Yes No Yes NoPNP/NPN output HIGH LOW LOW HIGHFunction indicator (yellow) On Off Off On
Output function
Connection diagram
DC 12...30VQN - NPN outputQP - PNP outputblack
whitebrown
wire colors refer to standard cable, not included
12
0Vblue34
loadload
M8 Connector
3 1
4 2
Leuze electronic GmbH + Co. KG In der Braike 1 D-73277 Owen Tel. +49 (0) 7021 573-0info@leuze.de • www.leuze.com
We
rese
rve
the
right
to m
ake
chan
ges
• D
S_G
K14
_EN
.fm
Forked sensor for reliable detection of transparent and opaque labelsPNP and NPN transistor output for optimum adaptation to the controllerRobust metal housing with beveled inlet edgesInverting input for easy adaptation of the output signal level
1mm
10 - 30 VDC
Accessories:(available separately)
M12 connectors (KD …)Ready-made M12 cables (K-D...)
IP 65
Dimensioned drawing
!
"
A SensorB Mouth depthC Display switching outputD Display base adjustmentE Base adjustmentF Sensitivity adjustment:
Clockwise rotation = increase sensitivity
! + " Direction of label-tape movement
Electrical connection
GK 14 Capacitive forked sensor
GK 14/24 L - 07
Specifications and descriptionEN
07-
2009
/08
5011
0462
GK 14/24 L - 07 2009/08
SpecificationsOptical dataMouth width 0.9mm ± 0.1mmMouth depth 85mm
TimingSwitching frequency 1)
1) Max. label speed 10m/s, min. label gap 2mm
5000HzResponse time 0.1msDelay before start-up ≤ 100ms
Electrical dataOperating voltage UB 10 … 30VDC (incl. residual ripple)Residual ripple ≤ 15% of UBOpen-circuit current ≤ 35mASwitching output 1 PNP transistor output
1 NPN transistor outputFunction characteristics direction dependent, reversible Signal voltage high/low ≥ (UB-2V)/≤ 2VOutput current 200mASensitivity adjustable with multiturn potentiometerBase adjustment adjustable with multiturn potentiometer
IndicatorsYellow LED label/gap LED yellow (2x) base adjustment
Mechanical data Housing aluminum, anodizedWeight 175g Connection type M12 connector, 5-pin
Environmental dataAmbient temp. (operation/storage) 0°C … +60°CProtective circuit 2)
2) 1=polarity reversal protection, 2=short-circuit protection for all outputs
1, 2 VDE safety class IIIProtection class IP 65
OptionsInverting input high/low ≥ 8V/≤ 2VInput resistance 10kΩ
RemarksSwitching behavior dependent on the infeed directionDepending on the direction of movement of the label tape through the sensor, the following switching behavior occurs at the outputs:
MountingFor optimum function of the capacitive forked sensor, the sensor should be mounted on a metallic ma-chine part. A lock washer (e.g DIN 6797) should be placed under the screw head to secure the sensor.Approved purpose:The GK 14 forked sensors are sensors for the capacitive detection of labels on a carrier tape. This prod-uct is only to be commissioned and used for the approved purpose by qualified personnel. This sensor is not a protective sensor and is not to be used for personnel protection.
Order guide
Direction of movementSwitching outputs pin 2 + pin 4
Pin 5 not connected or 0V Operating voltage UB at pin 5
! Signal in the gap Signal on the label" Signal on the label Signal in the gap
Designation Part No.
Rear connector GK 14/24 L 500 26371Top connector GK 14/24 L.2 500 31714
Tables
Diagrams
RemarksBase setting- Set sensitivity to max. (turn
potentiometer to the right), then turn back 1/2 turn to the left.
- Base adjustment without la-bel tape such that both LEDs are equally bright.
- If necessary, reduce the sensitivity setting (in steps of 1/4 turn to the left).
Base adjustmentPerform after new mounting, cleaning, sensitivity increase.Switching behaviorA signal change at the switching output occurs when a label enters at the minimum speed. The output signal remains constant until the next edge of an exiting or entering label is detected.
GK 14
Recommended