View
243
Download
4
Category
Preview:
Citation preview
ANSI Class 150 and 300GATE, GLOBE & CHECK VALVES
Y-STRAINERS
API 603 STAINLESS STEEL VALVES
OneSteel Trading Limited ABN 50 007 519 646Valves & Actuation National Office - Phone: 03 9566 9776 • Fax: 03 9566 9735
valves@onesteel.com
CONTACT YOUR NEAREST ONESTEEL OFFICE
Doc 73 October 2003
EMICO STAINLESS STEEL VALVES
COMPLY WITH API & ASME STANDARDS AND
ARE WIDELY USED IN CHEMICAL,
PETROCHEMICAL, FOOD & BEVERAGE, PULP &
PAPER, MINING AND OTHER PROCESS PLANTS
THROUGHOUT THE WORLD.
EMICO VALVES ARE MANUFACTURED UNDER
STRICT QUALITY CONTROL AND ARE SUITABLE
FOR USE IN CORROSION RESISTANT
APPLICATIONS.
OneSteel has taken reasonable care to ensure accuracy of the material in this ‘catalogue’ but you should not rely on the whole or any part of the information whichis subject to change without notice for reasons including error rectification, product discontinuation, new product introduction. OneSteel expresslydisclaims all liability whatsoever for (including any direct or indirect loss or damage, costs or expenses howsoever incurred by any person) or reliance on the wholeor any part of the information contained in or omitted from this ‘catalogue’ and recommends that you verify any information with your independent expert adviserand rely solely on that adviser’s recommendations.
Flanged end valve ratings terminate at 538°C (1000°F).
ValveClosure
TestPressure
Hydrostatic ShellTest Pressure
CLASS
°C-29~+38
93149204260316343371399427454482510538
°F-20~+100
2003004005006006507007508008509009501000
psig275235205190170140125110958065503520
psig275235215195170140125110958065503520
psig720600540495465435430425415405395390380320
psig720620560515480450445430425420420415385350
ANSI-150 ANSI-300Service Temperature CF8 CF8M CF8 CF8M
Hydrostatic
Air
425psig 1100psig
303psig 792psig
80psig 80psig
PRESSURE TEMPERATURE RATINGSASME B16.34-1996
C O N T E N T S
• ANSI 150 & 300 CAST STAINLESS STEEL GATE VALVES - pg 2/3
• ANSI 150 & 300 CAST STAINLESS STEEL GLOBE VALVES - pg 4/5
• ANSI 150 & 300 CAST STAINLESS STEEL CHECK VALVES - pg 6/7
• ANSI 150 CAST STAINLESS STEEL Y-STRAINER - pg 8
ANSI 150 CAST STAINLESS STEELY-STRAINER
DESCRIPTION
DESIGN STANDARDS
TEST PRESSURE
Raised Face flanged ends toANSI Class 150, bolted cover.Size range: 15mm through 300mm.
• Design - ASME B16.34• Shell Wall Thickness - ASME B16.34• Pressure /Temperature Rating -
ASME B16.34• Flange Dimension - ASME B16.5• Flange Gasket Facing -
ASME B16.5 (3.2 to 6.3 microns)
Per API 598 standards• ANSI 150 Shell (by Water) -425psig
8
SIZEB
60.570
79.598.5120.5139.5152.5190.5216
241.5298.5362432
in1/23/41
1 1/22
2 1/2345681012
mm15202540506580100125150200250300
E15202540506580100125150200250300
H7575100120140175196244277320390430600
L120140150190210250280340380420500700780
A8998108127152178190229254279343406483
C3543517392105127157186216270324381
D11.211.211.214.315.917.519.123.923.925.428.630.231.8
nø-d4-164-164-164-164-194-194-198-198-228-228-2212-2512-25
ANSI-150
n-ød
A B C E
D
L
H
45°
5 63 21 4
ANSI CLASS 150
DIMENSIONS (mm)
Y-
ST
RA
INE
R
Fig EAS-405
PARTS AND MATERIAL
NO. PARTS NAME MATERIAL 123456
BODYBONNETGASKETSCREENPLUGBONNET BOLT/ NUT
CF8MCF8M
PTFE (Option: Graphite)SS 316 *AISI 316
SUS 304 /AISI 304
* Screen for 15mm-50mm is punched stainless steel plate with 1mm Ø holes.Screen for 65mm and above is punched stainless steel plate with 1.5mm Ø holes.
ANSI 150 & 300 CAST STAINLESS STEELGATE VALVES
PARTS AND MATERIAL
DESCRIPTION
DESIGN STANDARDS
TEST PRESSURE
Raised Face flanged ends to ANSI Class 150and ANSI Class 300. Integral T-head stem,fully guided flexible wedge, self-aligning gland,integral body seats, outside screw and yoke,rising stem, non-rising handwheel.Size range: ANSI 150 - 15mm through 400mm.
ANSI 300 - 15mm through 300mm
• Design - API 603• Shell Wall Thickness - API 603• Pressure /Temperature Rating - ASME B16.34• Face to Face Dimension - ASME B16.10• Flange Dimension - ASME B16.5• Flange Gasket Facing -
ASME B16.5 (3.2 to 6.3 microns)
Per API 598 standards• ANSI 150 Shell (by Water) -425psig• ANSI 150 Seat (by Water) -303psig
(by Air) - 80psig• ANSI 300 Shell (by Water) -1100psig• ANSI 300 Seat (by Water) -792psig
(by Air) - 80psig
2
1234567891011
BODYBONNETSTEMDISCGLAND FLANGEGLAND PACKINGHANDWHEELBODY/BONNET GASKETBODY/BONNET BOLTINGGLAND BOLT/NUTYOKE SLEEVE
Stainless Steel ASTM A351 CF8MStainless Steel ASTM A351 CF8MAISI-316ASTM A351 CF8MASTM A351 CF8MPTFE (Option: Graphite)Ductile IronPTFE (Option: Graphite)ASTM A193 B8 /A194 Gr. 8ASTM A193 B8 /A194 Gr. 8Ductile Iron
NO. PARTS NAME MATERIAL
GA
TE
VA
LV
ES
ANSI 150 & 300 CAST STAINLESS STEELCHECK VALVES
E
n-ød
L
D
AB
C
H
5 8 2 4 7
3 6 1
E
n-ød
AB
C
H
L
D
5 8 2 4 7
3 6 1
7
ANSI CLASS 150
ANSI CLASS 300
DIMENSIONS (mm)
DIMENSIONS (mm)
SIZEB
60.570
79.598.5120.5139.5152.5190.5216
241.5298.5362432
in1/23/41
1 1/22
2 1/2345681012
mm15202540506580100125150200250300
E15202540506580100125150200250300
H63667585110135135170170210250315376
L108117127165203216241292330356495622698
A8998108127152178190229254279343406483
C3543517392105127157186216270324381
D11.211.211.214.315.917.519.123.923.925.428.630.231.8
nø-d4-164-164-164-164-194-194-198-198-228-228-2212-2512-25
ANSI-150
SIZEB
66.582.589
114.5127149168200235270330
387.5451
in1/23/41
1 1/22
2 1/2345681012
mm15202540506580100125150200250300
E15202540506580100125150200250300
H8090100116129143164177217231291319360
L152178216241267292318356400444533622711
A95117124156165190210254279318381444521
C3543517392105127157186216270324381
D14.315.917.520.722.325.428.631.835
36.641.347.750.8
nø-d4-164-194-194-228-198-228-228-228-2212-2212-2516-2916-32
ANSI-300
Fig EAS-306
Fig EAS-315
ANSI 150 & 300 CAST STAINLESS STEELCHECK VALVES
PARTS AND MATERIAL
DESCRIPTION
DESIGN STANDARDS
TEST PRESSURE
Raised Face flanged ends to ANSI Class 150and ANSI Class 300. Swing type disc, integralbody seat, bolted cover.Size range: ANSI 150 - 15mm through 300mm.
ANSI 300 - 15mm through 300mm
• Design - ASME B16.34• Shell Wall Thickness -
ASME B16.34• Pressure /Temperature Rating -
ASME B16.34• Face to Face Dimension -
ASME B16.10• Flange Dimension - ASME B16.5• Flange Gasket Facing -
ASME B16.5 (3.2 to 6.3 microns)
Per API 598 standards• ANSI 150 Shell (by Water) -425psig• ANSI 150 Seat (by Water) -303psig
(by Air) - 80psig• ANSI 300 Shell (by Water) -1100psig• ANSI 300 Seat (by Water) -792psig
(by Air) - 80psig
6
12345678
BODYCOVERDISCDISC NUTBODY/COVER BOLTINGARMBODY/COVER GASKETHINGE PIN
Stainless Steel ASTM A351 CF8MStainless Steel ASTM A351 CF8MASTM A351 CF8MSS 316ASTM A193 B8 /A194 Gr. 8ASTM A351 CF8MPTFE (Option: Graphite)SS 316
NO. PARTS NAME MATERIAL
CH
EC
K V
AL
VE
S
ANSI 150 & 300 CAST STAINLESS STEELGATE VALVES
A B C
DL
n-ød
E
H
W
(OPE
N)
7
11
10
5
6
3
9
2
8
1
4
A
(OPE
N)
B CH
n-ød
D
E
W
7
11
10
5
6
3
9
2
8
1
4
L
3
ANSI CLASS 150
ANSI CLASS 300
SIZEA8998108117127152178190229254279343406483533597
in1/23/41
1 1/41 1/2
22 1/2
3456810121416
mm1520253240506580100125150200250300350400
E1520253240506580100125150200250300350400
H1902002302702803203904155106007109001117132414801658
W9090100140140160180200225250290330350400550600
L108117127140165178190203229254267292330356381406
B60.570
79.589
98.5120.5139.5152.5190.5216
241.5298.5362432
476.5539.7
C354351647392105127157186216270324381413470
D11.211.211.214.314.315.917.519.123.923.925.428.630.231.835
36.6
nø-d4-164-164-164-164-164-194-194-198-198-228-228-2212-2512-2512-2916-29
ANSI-150
DIMENSIONS (mm)
SIZEA95117124156165190210254279318381444521
in1/23/41
1 1/22
2 1/2345681012
mm15202540506580100125150200250300
E15202540506580100125150200250300
H16018021028033039045452563973993311381338
W100120140160180200224250250300350400500
L140152165190216241283305381403419457502
B66.582.589
114.5127149168200235270330
387.5451
C3543517392105127157186216270324381
D14.315.917.520.722.325.428.631.835
36.641.347.750.8
nø-d4-164-194-194-228-198-228-228-228-2212-2212-2516-2916-32
ANSI-300
DIMENSIONS (mm)
Fig EAS-105
Fig EAS-115
ANSI 150 & 300 CAST STAINLESS STEELGLOBE VALVES
ANSI 150 & 300 CAST STAINLESS STEELGLOBE VALVES
PARTS AND MATERIAL
DESCRIPTION
DESIGN STANDARDS
TEST PRESSURE
Raised Face flanged ends to ANSI Class 150and ANSI Class 300. Integral T-head stem,swivel disc, self-aligning gland,integral seat, bolted bonnet, outside screw andyoke, rising stem and handwheel.Size range: ANSI 150 - 15mm through 300mm.
ANSI 300 - 15mm through 300mm
• Design - ASME B16.34• Shell Wall Thickness -
ASME B16.34• Pressure /Temperature Rating -
ASME B16.34• Face to Face Dimension -
ASME B16.10• Flange Dimension - ASME B16.5• Flange Gasket Facing -
ASME B16.5 (3.2 to 6.3 microns)
Per API 598 standards• ANSI 150 Shell (by Water) -425psig• ANSI 150 Seat (by Water) -303psig
(by Air) - 80psig• ANSI 300 Shell (by Water) -1100psig• ANSI 300 Seat (by Water) -792psig
(by Air) - 80psig
4
H
n-ød
D
L
W
B C EA
(OPE
N)
7
11
5
2
6
3
4
1
10
9
8
H
n-ød
D
L
W
B C EA
(OPE
N)
11
5
6
8
3
4
10
9
2
7
1
5
ANSI CLASS 150
ANSI CLASS 300
1234567891011
BODYBONNETSTEMDISCGLAND FLANGEGLAND PACKINGHANDWHEELBODY/BONNET GASKETBODY/BONNET BOLTINGGLAND BOLT/NUTYOKE SLEEVE
Stainless Steel ASTM A351 CF8MStainless Steel ASTM A351 CF8MAISI-316ASTM A351 CF8MASTM A351 CF8MPTFE (Option: Graphite)Ductile IronPTFE (Option: Graphite)ASTM A193 B8 /A194 Gr. 8ASTM A193 B8 /A194 Gr. 8Ductile Iron
NO. PARTS NAME MATERIAL
DIMENSIONS (mm)
DIMENSIONS (mm)
SIZEA8998108127152178190229254279343406483
in1/23/41
1 1/22
2 1/2345681012
mm15202540506580100125150200250300
E15202540506580100125150200250300
H190200230240250270290350410520570670736
W90100100140160180200225250300350400500
L108117127165203216241292356406495622698
B60.570
79.598.5120.5139.5152.5190.5216
241.5298.5362432
C3543517392105127157186216270324381
D11.211.211.214.315.917.519.123.923.925.428.630.231.8
nø-d4-164-164-164-164-194-194-198-198-228-228-2212-2512-25
ANSI-150
SIZEA95117124156165190210254279318381444521
in1/23/41
1 1/22
2 1/2345681012
mm15202540506580100125150200250300
E15202540506580100125150200250300
H165173175225268301330390464510570630720
W100100140160180200220250320350400450500
L152178203229267292318356400444559622711
B66.582.589
114.5127149168200235270330
387.5451
C3543517392105127157186216270324381
D14.315.917.520.722.325.428.631.835
36.641.347.750.8
nø-d4-164-194-194-228-198-228-228-228-2212-2212-2516-2916-32
ANSI-300
GL
OB
E V
AL
VE
S
Fig EAS-205
Fig EAS-215
ANSI 150 & 300 CAST STAINLESS STEELGLOBE VALVES
ANSI 150 & 300 CAST STAINLESS STEELGLOBE VALVES
PARTS AND MATERIAL
DESCRIPTION
DESIGN STANDARDS
TEST PRESSURE
Raised Face flanged ends to ANSI Class 150and ANSI Class 300. Integral T-head stem,swivel disc, self-aligning gland,integral seat, bolted bonnet, outside screw andyoke, rising stem and handwheel.Size range: ANSI 150 - 15mm through 300mm.
ANSI 300 - 15mm through 300mm
• Design - ASME B16.34• Shell Wall Thickness -
ASME B16.34• Pressure /Temperature Rating -
ASME B16.34• Face to Face Dimension -
ASME B16.10• Flange Dimension - ASME B16.5• Flange Gasket Facing -
ASME B16.5 (3.2 to 6.3 microns)
Per API 598 standards• ANSI 150 Shell (by Water) -425psig• ANSI 150 Seat (by Water) -303psig
(by Air) - 80psig• ANSI 300 Shell (by Water) -1100psig• ANSI 300 Seat (by Water) -792psig
(by Air) - 80psig
4
H
n-ød
D
L
W
B C EA
(OPE
N)
7
11
5
2
6
3
4
1
10
9
8
H
n-ød
D
L
W
B C EA
(OPE
N)
11
5
6
8
3
4
10
9
2
7
1
5
ANSI CLASS 150
ANSI CLASS 300
1234567891011
BODYBONNETSTEMDISCGLAND FLANGEGLAND PACKINGHANDWHEELBODY/BONNET GASKETBODY/BONNET BOLTINGGLAND BOLT/NUTYOKE SLEEVE
Stainless Steel ASTM A351 CF8MStainless Steel ASTM A351 CF8MAISI-316ASTM A351 CF8MASTM A351 CF8MPTFE (Option: Graphite)Ductile IronPTFE (Option: Graphite)ASTM A193 B8 /A194 Gr. 8ASTM A193 B8 /A194 Gr. 8Ductile Iron
NO. PARTS NAME MATERIAL
DIMENSIONS (mm)
DIMENSIONS (mm)
SIZEA8998108127152178190229254279343406483
in1/23/41
1 1/22
2 1/2345681012
mm15202540506580100125150200250300
E15202540506580100125150200250300
H190200230240250270290350410520570670736
W90100100140160180200225250300350400500
L108117127165203216241292356406495622698
B60.570
79.598.5120.5139.5152.5190.5216
241.5298.5362432
C3543517392105127157186216270324381
D11.211.211.214.315.917.519.123.923.925.428.630.231.8
nø-d4-164-164-164-164-194-194-198-198-228-228-2212-2512-25
ANSI-150
SIZEA95117124156165190210254279318381444521
in1/23/41
1 1/22
2 1/2345681012
mm15202540506580100125150200250300
E15202540506580100125150200250300
H165173175225268301330390464510570630720
W100100140160180200220250320350400450500
L152178203229267292318356400444559622711
B66.582.589
114.5127149168200235270330
387.5451
C3543517392105127157186216270324381
D14.315.917.520.722.325.428.631.835
36.641.347.750.8
nø-d4-164-194-194-228-198-228-228-228-2212-2212-2516-2916-32
ANSI-300
GL
OB
E V
AL
VE
S
Fig EAS-205
Fig EAS-215
ANSI 150 & 300 CAST STAINLESS STEELCHECK VALVES
PARTS AND MATERIAL
DESCRIPTION
DESIGN STANDARDS
TEST PRESSURE
Raised Face flanged ends to ANSI Class 150and ANSI Class 300. Swing type disc, integralbody seat, bolted cover.Size range: ANSI 150 - 15mm through 300mm.
ANSI 300 - 15mm through 300mm
• Design - ASME B16.34• Shell Wall Thickness -
ASME B16.34• Pressure /Temperature Rating -
ASME B16.34• Face to Face Dimension -
ASME B16.10• Flange Dimension - ASME B16.5• Flange Gasket Facing -
ASME B16.5 (3.2 to 6.3 microns)
Per API 598 standards• ANSI 150 Shell (by Water) -425psig• ANSI 150 Seat (by Water) -303psig
(by Air) - 80psig• ANSI 300 Shell (by Water) -1100psig• ANSI 300 Seat (by Water) -792psig
(by Air) - 80psig
6
12345678
BODYCOVERDISCDISC NUTBODY/COVER BOLTINGARMBODY/COVER GASKETHINGE PIN
Stainless Steel ASTM A351 CF8MStainless Steel ASTM A351 CF8MASTM A351 CF8MSS 316ASTM A193 B8 /A194 Gr. 8ASTM A351 CF8MPTFE (Option: Graphite)SS 316
NO. PARTS NAME MATERIAL
CH
EC
K V
AL
VE
S
ANSI 150 & 300 CAST STAINLESS STEELGATE VALVES
A B C
DL
n-ød
E
H
W
(OPE
N)
7
11
10
5
6
3
9
2
8
1
4
A
(OPE
N)
B CH
n-ød
D
E
W
7
11
10
5
6
3
9
2
8
1
4
L
3
ANSI CLASS 150
ANSI CLASS 300
SIZEA8998108117127152178190229254279343406483533597
in1/23/41
1 1/41 1/2
22 1/2
3456810121416
mm1520253240506580100125150200250300350400
E1520253240506580100125150200250300350400
H1902002302702803203904155106007109001117132414801658
W9090100140140160180200225250290330350400550600
L108117127140165178190203229254267292330356381406
B60.570
79.589
98.5120.5139.5152.5190.5216
241.5298.5362432
476.5539.7
C354351647392105127157186216270324381413470
D11.211.211.214.314.315.917.519.123.923.925.428.630.231.835
36.6
nø-d4-164-164-164-164-164-194-194-198-198-228-228-2212-2512-2512-2916-29
ANSI-150
DIMENSIONS (mm)
SIZEA95117124156165190210254279318381444521
in1/23/41
1 1/22
2 1/2345681012
mm15202540506580100125150200250300
E15202540506580100125150200250300
H16018021028033039045452563973993311381338
W100120140160180200224250250300350400500
L140152165190216241283305381403419457502
B66.582.589
114.5127149168200235270330
387.5451
C3543517392105127157186216270324381
D14.315.917.520.722.325.428.631.835
36.641.347.750.8
nø-d4-164-194-194-228-198-228-228-228-2212-2212-2516-2916-32
ANSI-300
DIMENSIONS (mm)
Fig EAS-105
Fig EAS-115
ANSI 150 & 300 CAST STAINLESS STEELGATE VALVES
PARTS AND MATERIAL
DESCRIPTION
DESIGN STANDARDS
TEST PRESSURE
Raised Face flanged ends to ANSI Class 150and ANSI Class 300. Integral T-head stem,fully guided flexible wedge, self-aligning gland,integral body seats, outside screw and yoke,rising stem, non-rising handwheel.Size range: ANSI 150 - 15mm through 400mm.
ANSI 300 - 15mm through 300mm
• Design - API 603• Shell Wall Thickness - API 603• Pressure /Temperature Rating - ASME B16.34• Face to Face Dimension - ASME B16.10• Flange Dimension - ASME B16.5• Flange Gasket Facing -
ASME B16.5 (3.2 to 6.3 microns)
Per API 598 standards• ANSI 150 Shell (by Water) -425psig• ANSI 150 Seat (by Water) -303psig
(by Air) - 80psig• ANSI 300 Shell (by Water) -1100psig• ANSI 300 Seat (by Water) -792psig
(by Air) - 80psig
2
1234567891011
BODYBONNETSTEMDISCGLAND FLANGEGLAND PACKINGHANDWHEELBODY/BONNET GASKETBODY/BONNET BOLTINGGLAND BOLT/NUTYOKE SLEEVE
Stainless Steel ASTM A351 CF8MStainless Steel ASTM A351 CF8MAISI-316ASTM A351 CF8MASTM A351 CF8MPTFE (Option: Graphite)Ductile IronPTFE (Option: Graphite)ASTM A193 B8 /A194 Gr. 8ASTM A193 B8 /A194 Gr. 8Ductile Iron
NO. PARTS NAME MATERIAL
GA
TE
VA
LV
ES
ANSI 150 & 300 CAST STAINLESS STEELCHECK VALVES
E
n-ød
L
D
AB
C
H
5 8 2 4 7
3 6 1
E
n-ød
AB
C
H
L
D
5 8 2 4 7
3 6 1
7
ANSI CLASS 150
ANSI CLASS 300
DIMENSIONS (mm)
DIMENSIONS (mm)
SIZEB
60.570
79.598.5120.5139.5152.5190.5216
241.5298.5362432
in1/23/41
1 1/22
2 1/2345681012
mm15202540506580100125150200250300
E15202540506580100125150200250300
H63667585110135135170170210250315376
L108117127165203216241292330356495622698
A8998108127152178190229254279343406483
C3543517392105127157186216270324381
D11.211.211.214.315.917.519.123.923.925.428.630.231.8
nø-d4-164-164-164-164-194-194-198-198-228-228-2212-2512-25
ANSI-150
SIZEB
66.582.589
114.5127149168200235270330
387.5451
in1/23/41
1 1/22
2 1/2345681012
mm15202540506580100125150200250300
E15202540506580100125150200250300
H8090100116129143164177217231291319360
L152178216241267292318356400444533622711
A95117124156165190210254279318381444521
C3543517392105127157186216270324381
D14.315.917.520.722.325.428.631.835
36.641.347.750.8
nø-d4-164-194-194-228-198-228-228-228-2212-2212-2516-2916-32
ANSI-300
Fig EAS-306
Fig EAS-315
C O N T E N T S
• ANSI 150 & 300 CAST STAINLESS STEEL GATE VALVES - pg 2/3
• ANSI 150 & 300 CAST STAINLESS STEEL GLOBE VALVES - pg 4/5
• ANSI 150 & 300 CAST STAINLESS STEEL CHECK VALVES - pg 6/7
• ANSI 150 CAST STAINLESS STEEL Y-STRAINER - pg 8
ANSI 150 CAST STAINLESS STEELY-STRAINER
DESCRIPTION
DESIGN STANDARDS
TEST PRESSURE
Raised Face flanged ends toANSI Class 150, bolted cover.Size range: 15mm through 300mm.
• Design - ASME B16.34• Shell Wall Thickness - ASME B16.34• Pressure /Temperature Rating -
ASME B16.34• Flange Dimension - ASME B16.5• Flange Gasket Facing -
ASME B16.5 (3.2 to 6.3 microns)
Per API 598 standards• ANSI 150 Shell (by Water) -425psig
8
SIZEB
60.570
79.598.5120.5139.5152.5190.5216
241.5298.5362432
in1/23/41
1 1/22
2 1/2345681012
mm15202540506580100125150200250300
E15202540506580100125150200250300
H7575100120140175196244277320390430600
L120140150190210250280340380420500700780
A8998108127152178190229254279343406483
C3543517392105127157186216270324381
D11.211.211.214.315.917.519.123.923.925.428.630.231.8
nø-d4-164-164-164-164-194-194-198-198-228-228-2212-2512-25
ANSI-150
n-ød
A B C E
D
L
H
45°
5 63 21 4
ANSI CLASS 150
DIMENSIONS (mm)
Y-
ST
RA
INE
R
Fig EAS-405
PARTS AND MATERIAL
NO. PARTS NAME MATERIAL 123456
BODYBONNETGASKETSCREENPLUGBONNET BOLT/ NUT
CF8MCF8M
PTFE (Option: Graphite)SS 316 *AISI 316
SUS 304 /AISI 304
* Screen for 15mm-50mm is punched stainless steel plate with 1mm Ø holes.Screen for 65mm and above is punched stainless steel plate with 1.5mm Ø holes.
EMICO STAINLESS STEEL VALVES
COMPLY WITH API & ASME STANDARDS AND
ARE WIDELY USED IN CHEMICAL,
PETROCHEMICAL, FOOD & BEVERAGE, PULP &
PAPER, MINING AND OTHER PROCESS PLANTS
THROUGHOUT THE WORLD.
EMICO VALVES ARE MANUFACTURED UNDER
STRICT QUALITY CONTROL AND ARE SUITABLE
FOR USE IN CORROSION RESISTANT
APPLICATIONS.
EMICO has taken reasonable care to ensure accuracy of the material in this ‘catalogue’ but you should not rely on the whole or any part of the information whichis subject to change without notice for reasons including error recti�cation, product discontinuation, new product introduction. EMICO expresslydisclaims all liability whatsoever for (including any direct or indirect loss or damage, costs or expenses howsoever incurred by any person) or reliance on the wholeor any part of the information contained in or omitted from this ‘catalogue’ and recommends that you verify any information with your independent expert adviserand rely solely on that adviser’s recommendations.
Flanged end valve ratings terminate at 538°C (1000°F).
ValveClosure
TestPressure
Hydrostatic ShellTest Pressure
CLASS
°C-29~+38
93149204260316343371399427454482510538
°F-20~+100
200300400500600650700750800850900950
1000
psig275235205190170140125110958065503520
psig275235215195170140125110958065503520
psig720600540495465435430425415405395390380320
psig720620560515480450445430425420420415385350
ANSI-150 ANSI-300Service Temperature CF8 CF8M CF8 CF8M
Hydrostatic
Air
425psig 1100psig
303psig 792psig
80psig 80psig
PRESSURE TEMPERATURE RATINGSASME B16.34-1996
ANSI Class 150 and 300GATE, GLOBE & CHECK VALVES
Y- STRAINERS
API 603 STAINLESS STEEL VALVES
EMICO Australia Pty Ltd - Phone: 03 9878 8653
October 2003
Recommended