View
6
Download
0
Category
Preview:
Citation preview
Instructions for Use
Advantix Vario end closing piece
for extension
Model Year built (from)4965.16 06/2013
INT
Table of contents
1 About these instructions for use 3
1.1 Target groups 31.2 About this translated version 31.3 Other applicable documents 3
2 Product information 4
2.1 Standards and regulations 42.2 Certification 52.3 Product description 6
2.3.1 Overview of the components 7
2.4 Required accessories 8
3 Handling 9
3.1 Assembly information 93.1.1 Tools and materials 93.1.2 Installation dimensions 9
3.2 Assembly 103.3 Disposal 12
Table of contents
Advantix Vario end closing piece 2
1 About these instructions for use
Trade mark rights exist for this document; for further information, go toviega.com/legal.
1.1 Target groupsThe information in this instruction manual is directed at the followinggroups of people:
n Heating and sanitary professionals and trained personneln Tilers
Individuals without the abovementioned training or qualification are notpermitted to mount, install and, if required, maintain this product. Thisrestriction does not extend to possible operating instructions.
The installation of Viega products must take place in accordance withthe general rules of engineering and the Viega instructions for use.
1.2 About this translated versionThis instruction for use contains important information about the choiceof product or system, assembly and commissioning as well as intendeduse and, if required, maintenance measures. The information about theproducts, their properties and application technology are based on thecurrent standards in Europe (e.g. EN) and/or in Germany(e.g. DIN/DVGW).
Some passages in the text may refer to technical codes in Europe/Germany. These should serve as recommendations in the absence ofcorresponding national regulations. The relevant national laws, stand‐ards, regulations, directives and other technical provisions take priorityover the German/European directives specified in this manual: Theinformation herein is not binding for other countries and regions; as saidabove, they should be understood as a recommendation.
1.3 Other applicable documentsThis instruction for use describes the mounting of an extension piece foran Advantix Vario shower channel in rough steps.
The instructions for use of the Advantix Vario showerchannel must also be strictly observed for the mounting ofthe extension piece.
About these instructions for use
Advantix Vario end closing piece 3
2 Product information
2.1 Standards and regulationsThe following standards and regulations apply to Germany / Europe andare provided as a support feature.
Regulations from section: Sealing
Scope / Notice Regulations applicable in Ger‐many
Stress class of the underground,as well as suitable bonded sealing
ZDB-Merkblatt 8/2012
Stress class of the underground,as well as suitable bonded sealing
Leitfaden zur Abdichtung im Ver‐bund (AIV)
Approved bonded sealings withproof of practicability in keepingwith building law for stressclasses A and AO
ETAG 022 T1
Approved bonded sealings withproof of practicability in keepingwith building law for stressclasses A, B and C
DIBt-Bauregelliste A, Teil 2 desDIBt und Prüfgrundsätze fürAbdichtungen im Verbund(PG AIV-F)
Permitted bonded sealings EN 14891
Sealing of inside rooms DIN18534
Regulations from section: Media
Scope / Notice Regulations applicable in Ger‐many
Typical domestic wastewater DIN 1986-3
Product information
Advantix Vario end closing piece 4
2.2 CertificationData acc. to DIN EN 1253, Table 7
Manufacturer Viega Holding GmbH & Co.KG
Manufacturer identification mark
Certificate of conformity
Address Viega Technology GmbH & Co.KGViega Platz 1 57439 Attendorn Germany
Viega Technology GmbH & Co.KGViega Platz 1 57439 Attendorn Germany
Relevant standard DIN EN 1253-1
Product class with respect totemperature behaviour
A
Product information
Advantix Vario end closing piece 5
2.3 Product descriptionend closing piece
Instead of the closing cap, a long element, the so-called "end closingpiece" can be mounted onto the base unit. The base unit can thereforebe extended accordingly.
a
b
c
d
Fig. 1: Installation possibilities with end closing piece
a max. 1451 mmb max. 1680 mmc max. 2651 mmd max. 2880 mm
Product information
Advantix Vario end closing piece 6
2.3.1 Overview of the components
Fig. 2: end closing piece, scope of delivery
1 protective insert made of hard foam2 protective foil3 End closing piece4 Allen key size 45 sealing tape6 foot, height-adjustable7 fixing material8 screws9 spacer
Product information
Advantix Vario end closing piece 7
2.4 Required accessoriesPer installed component, one corresponding standing grate set isrequired. The complete range and the required information can be foundin the catalogue.
Fig. 3: Standing grate set
Product information
Advantix Vario end closing piece 8
3 Handling
3.1 Assembly information3.1.1 Tools and materials
You require
n screwdrivern Allen key size 4
Mounting adhesive can be used for a maximum of 18 months.
The filling date is found on the top edge of the cartridge. The first twonumbers represent the month, the following number the year.
Example085...Filling date = August (08) 2015 (5)
3.1.2 Installation dimensions
10
33
110
275
Fig. 5: Dimensions of end closing piece
Mounting adhesive
Fig. 4: Filling date of the mountingadhesive
Handling
Advantix Vario end closing piece 9
3.2 Assembly
Fig. 6: Installation variation
Do not shorten end closing piece!
▶ Screw the end closing piece onto the profile.
When using a cordless screwdriver, make the last few turns byhand.Only tighten screws hand-tight!
▷ The end closing piece is properly mounted when the seal ispushed together gently.
Mount adjustable feet, see instructions for use of the Advantix Varioshower channel.
Mounting the end closing piece
M 3 NmA
4
≤
Handling
Advantix Vario end closing piece 10
▶ Align the shower channel and connection piece horizontally to oneanother.
▶ Insert spacer.
The spacers prevent the shower channel from being deformed whenthe screed hardens later.
▶ If necessary, shorten the protective foil and stick onto the flange.
▶ Line shower channel with screed (also see instructions for use of theshower channel).
▶ Leave screed to harden.
Aligning the end closing piece
Preparing for further work
Handling
Advantix Vario end closing piece 11
▶ Remove protective foil (1).
▶ Remove spacer (2).
▶ If necessary, clean the flange, e. g. with isopropanol.
▶ Cut protective insert to size and insert (3).
▶ Apply mounting and spread mounting adhesive (also see instruc‐tions for use of the shower channel).
▶ Apply bonded sealing (also see instructions for use of the showerchannel).
▶ Cut the sealing tape generously.
▶ Position the sealing tape on the flange so that the flange and screedare uniformly covered.
Overlap the corners in the process.
▶ Rework the sticking points with a roller.
Further processing see instructions for use of the shower channel.
3.3 DisposalSeparate the product and packaging materials (e. g. paper, metal,plastic or non-ferrous metals) and dispose of in accordance with validnational legal requirements.
1.
2.3.
Handling
Advantix Vario end closing piece 12
Viega Technology GmbH & Co. KGservice-technik@viega.deviega.com
INT • 2020-02 • VPN190532
Recommended