A tale of three (identical) scanners - ctug.org.uk tale of three (identical) scanners.pdf · A tale...

A tale of three

(identical) scanners

Gareth Iball, Lizzy Crawford, Samir Dawoud

Leeds Teaching Hospitals NHS Trust

This is an edited version of the presentation

that was given at the CT Users Group

meeting.

Background

October 2007: three Siemens Sensation 64

systems installed in new hospital wing

Serial numbers: 55220, 55224, 55226

Commissioned by MPE – all results very

comparable

Protocols set up by Siemens on one scanner,

copied across to other two systems

Into clinical use January 2008

Department layout

CT 1

CT 2

CT 3

Patient dose survey - 2008

Audit against current national DRLs

Head, abdo/pelvis, CAP, chest/liver, HRCT

No patient size information

Some comments on large/small patients

Abdomen/pelvis scans

Average DLP for abdo/pelvis scans

0

100

200

300

400

500

600

700

800

CT 1 CT 2 CT 3

DL

P (

mG

ycm

)

Average DLP

DRL DLP

120kV, 200 Q.Ref mAs, 24x1.2mm, 5mm images, pitch = 1.4, CARE Dose 4D on

Follow up

Why the difference?

CT 2 – used for all ICU/HDU patients

Many scanned with arms down higher doses

CT 3 – quite a few large patients in the sample

Suggested lowering mAs to 180 Q.Ref mAs

No subsequent image quality issues reported

3rd UK CT Dose Survey

Set trainees on abdomen/pelvis dose surveys

from PACS

CTDIvol, DLP, AP & lateral sizes

30 patients from across the 3 scanners

Chose 10 patients from each scanner in order to

compare

Found something strange…

His original data

CTDIvol noticeably higher for small patients on CT 2

All ‘arms down’ patients excluded from the data set

CTDIvol variation with patient size for abdomen/pelvis scans

0

2

4

6

8

10

12

14

16

0 200 400 600 800 1000 1200 1400 1600

Cross sectional area (cm2)

CT

DIv

ol

(mG

y)

CT 1

CT 2

CT 3

Log. (CT 1)

Log. (CT 3)

Log. (CT 2)

With extra data

CTDI variation with patient size for abdomen/pelvis scans

R2 = 0.8174

R2 = 0.5111

R2 = 0.5956

0

2

4

6

8

10

12

14

16

0 200 400 600 800 1000 1200 1400 1600

Cross sectional area (cm2)

CT

DIv

ol

(mG

y)

CT1

CT2

CT3

Log. (CT1)

Log. (CT2)

Log. (CT3)

Average CTDIvol figures

CTDIvol (mGy) “Small” “Average” “Large”

CT 1 7.4 10.6 12.0

CT 2 11.8 13.1 13.4

CT 3 9.0 10.0 11.7

Definitely something strange with CT 2

Suspect CARE Dose not functioning properly

Attempt at CT AEC testing

Other trainees looking

at method of routine

AEC testing

Modified CTDI

phantoms

mA values obtained

using DICOM Info

Extractor software

DICOM Info Extractor v1.0.0.0 www.infomed.gr

Initial CARE Dose 4D tests

mA variation for range of CARE Dose 4D settings

0.0

20.0

40.0

60.0

80.0

100.0

120.0

140.0

160.0

0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150

Image number

Ap

pli

ed

mA

s

Average/Weak

Average/Average

Average/Strong

Strong/Weak

Strong/Average

Strong/Strong

Weak/Average

Weak/Weak

Weak/Strong

CARE Dose 4D test

mA variation along length of modified CTDI phantoms

0

50

100

150

200

250

0 20 40 60 80 100 120 140 160 180

Image number

Ap

pli

ed

mA

CT1

CT2

CT3

We’d used a chest protocol, but all seemed ok now?

Check protocols

Routine abdomen/pelvis:

120kV, 180 Q.Ref mAs, 24x1.2mm, 1 & 5mm

images, pitch = 1.4

CARE Dose 4D settings: Weak/Strong

Same on all the scanners

Repeat dose survey

CTDI variation with patient size for abdomen/pelvis scans

R2 = 0.7584

R2 = 0.7685

R2 = 0.6594

0

2

4

6

8

10

12

14

16

0 200 400 600 800 1000 1200 1400

Cross sectional area (cm2)

CT

DIv

ol

(mG

y)

CT 1

CT 2

CT 3

Log. (CT 1)

Log. (CT 2)

Log. (CT 3)

Data from the same week as we performed the CARE Dose 4D tests

Retrospective doses – June ‘08

CTDI variation with patient size for abdomen/pelvis scans

R2 = 0.5916

R2 = 0.8268

R2 = 0.7533

0

5

10

15

20

25

0 200 400 600 800 1000 1200 1400 1600 1800

Cross-sectional area (cm2)

CT

DIv

ol

(mG

y)

CT1

CT2

CT3

Log. (CT2)

Log. (CT3)

Log. (CT1)

Further investigations…

All scans performed with clinical

abdomen/pelvis scan protocol

Modified CTDI phantoms

Offset modified CTDI phantoms

CIRS virtually human pelvis phantom

mA variation

Noise measurements

Modified CTDI phantoms

DLP (mGycm):

CT1: 263

CT2: 283

CT3: 276

Offset, modified CTDI phantoms

DLP (mGycm):

CT1: 261

CT2: 291

CT3: 266

Pelvis phantom

DLP (mGycm):

CT1: 482

CT2: 588

CT3: 504

Noise measurements

CT

number

Noise

(s.d.)

CT 1 40.77 23.93

CT 2 41.98 19.73

CT 3 44.12 24.84

Investigations with Siemens

Day 1:

MPE AEC tests performed again – same results

Siemens performed their CARE Dose 4D – all ok

Still no clearer

Suggestion from Siemens

“One possibility for the observed behaviour is, that the scan protocols used at the three scanners, although having the same scan parameter settings, may originate from different Siemens protocols.

The mAs adaptation of CARE Dose 4D is based on the ref. mAs and the related reference attenuation. The latter is stored in the system and depends on the body part for which the original Siemens protocol was built.

If for instance the protocol at scanner 2 is based on a thorax protocol, while the protocols at scanners 1 and 3 are based on a pelvis protocol, the dose at scanner 2 will be higher, because the ref. mAs at scanner 2 is related to the typical attenuation of a thorax, while the ref. mAs of scanner 1 and 3 is related to the (higher) attenuation of a typical pelvis.”

Recommended test

“Use for a test the same original Siemens

protocol (e.g. Pelvis Routine) for all three

scanners and scan the pelvis phantom

(accurate phantom positioning is essential) -

is the dose now identical?”

Investigations with Siemens

Day 2:

Scan pelvis phantom on clinical and Siemens

standard protocols

Protocol comparison

mA variation along the length of the CIRS pelvis phantom

0

100

200

300

400

500

600

700

0 50 100 150 200 250 300

Image number

Ap

pli

ed

mA

CT 2 clinical protocol

CT 2 Siemens protocol

CT 3 Siemens protocol

DLP (mGycm):

CT2 clinical: 588

CT2 Siemens: 551

CT3 Siemens: 551

Shows no problem with CARE Dose but a protocol problem. Siemens were correct

Investigations with Siemens

Day 3:

Delete all scan protocols from CT 2 and replace

with scan protocols from CT 3 (hoping that there

were no other protocol errors on CT 3…)

After protocol replacement

mA variation along the length of the CIRS pelvis phantom

0

100

200

300

400

500

600

700

0 50 100 150 200 250 300

Image number

Ap

pli

ed

mA

CT 1

CT 2

CT 3

DLP (mGycm):

CT1: 482

CT2: 493

CT3: 504

Follow up dose survey

CTDIvol variation with patient size for abdomen/pelvis scans

0

2

4

6

8

10

12

14

16

18

20

0 200 400 600 800 1000 1200 1400

Cross sectiona area (cm2)

CT

DIv

ol

(mG

y)

CT 1

CT 2

CT 3

Log. (CT 1)

Log. (CT 2)

Log. (CT 3)

Summary

Even though the protocols appeared identical

they were very different!

Reference attenuation is different for each

body part and affects dose significantly

No display of the body part on which a

protocol is based

Problem only identified because we have 3

identical scanners

Implications for Leeds

Protocols to only be created/amended by CT

Team Leaders

More regular & robust patient dose audit

programme

Need a system for regularly auditing scan

protocols – IR(ME)R requirement

How?? We have 13 scanners in Leeds Trust

alone, maybe 50-100 protocols per scanner…

Could it happen elsewhere?

DLP vs patient size for VHRCT

0

100

200

300

400

500

0 200 400 600 800 1000 1200 1400

Cross sectional area (cm²)

DL

P (

mG

ycm

)

Leeds Sensation 64

Leeds Definition 64

Leeds Sensation 16

Log. (Leeds Sensation 64)

Log. (Leeds Definition 64)

Log. (Leeds Sensation 16)

64 slice: 120kV, 100 Q.Ref mAs, 64x0.6mm, pitch=1.2, CD4D: Weak/Strong

16 slice: 120kV, 100 Q.Ref mAs, 16x0.75mm, pitch=0.85, CD4D: Average/Average

Could it happen elsewhere?

64 slice: 120kV, 100 Q.Ref mAs, 64x0.6mm, pitch=1.2, CD4D: Weak/Strong

16 slice: 120kV, 100 Q.Ref mAs, 16x0.75mm, pitch=0.85, CD4D: Average/Average

DLP vs patient size for VHRCT

0

100

200

300

400

500

0 200 400 600 800 1000 1200 1400

Cross sectional area (cm²)

DL

P (

mG

yc

m)

Leeds Sensation 64

Leeds Definition 64

Leeds Sensation 16

York Sensation 16

Log. (Leeds Sensation 64)

Log. (Leeds Definition 64)

Log. (Leeds Sensation 16)

Log. (York Sensation 16)

mA variation along length of Lungman phantom

0

50

100

150

200

250

0 50 100 150 200 250 300

Image number

Ap

pli

ed

mA

Clinical VHRCT 100mAs

Siemens VHRCT 100mAs

Siemens abdomen modified to 100mAs

Siemens VHRCT modified to 80mAs

No complaints from Radiologists about the image quality on this scanner.

All Siemens scanners in Trust using 100 Q.Ref mAs for VHRCT. Can we now reduce

them all to 80mAs to match the dose on the 16 slice machine?

Scan Lungman phantom

DLP Clinical = 203

DLP Siemens = 250

DLP Abdomen = 203

DLP Siemens 80mAs = 197

Conclusions

Siemens protocols built for specific body

parts & shouldn’t be used for anything else

Raised a lot of issues for ourselves and

Siemens

Working through how to address them all

It could be happening to you

Thanks to

Gillian Ward, Becky Artschan, Dan Shaw

(Medical Physics, LTH)

Altan Senvar, Paul Playford, Anna Sedgwick

(Siemens Healthcare UK)