3dsmax Membuat Kursi Rotan

Dhany Faizal R

2012

Mej

a K

ayu

Penj

alin

.

Stikom Yos Sudarso

2

Step 1

Start by creating a new plane (Length = 55, Width = 96).

3

Step 2

Set the length segments to 24, and the width segments to 6. The horizontal segments are based

on how many rows of the pattern will be in your object. The vertical segments refer to how wide

each curve in each line will be, just make sure you go with an even number to avoid problems

later on.

4

Step 3

Convert your plane to an ‘Editable Poly’ (Right click on object > Convert to > Editable Poly).

5

Step 4

Select all of the vertices making up your vertical segments starting from the second column,

selecting 1 column and skipping another. To make multiple selections, simply hold ctrl.

Step 5

Now change your view and drag these vertices to the front. The degree to which you pull the

vertices will depend on how much curve you want to give your shape.

6

Step 6

Change back to your original view. Select any one of the horizontal edges, and press ‘Loop’

from the selection menu on the right.

Step 7

From the same menu, press ‘Ring’.

7

Step 8

Choose “create shape from outline” from the right side menu. Make sure you choose ‘smooth’,

this will allow the sharp corners created earlier to smooth out. Feel free to adjust the vertices that

you moved forward earlier, since you now have a better view of how it will look when it’s been

smoothed out.

8

Step 9

Go ahead and hide your original poly since you won’t be needing it anymore (Right Click > Hide

Selection). Note: You must be in object mode, not edge mode.

9

Step 10

Now you should have a new spline created in the shape of your final pattern. Go ahead and select

it.

10

Step 11

On the side menu, under the ‘Rendering’ tab, place a tick next to “Enable in Viewport”, and

choose the rectangular option. Depending on your units and scene size, choose a size that’s

reasonable, and make sure that the gap that it creates between one line and another can fit the

same line. This will be important for the next step. My settings were Length = 2, and Width = 1.

11

Step 12

Once you are satisfied with the width and height of your lines, select the object / spline as a

whole, then hold Shift + drag upwards to duplicate the same set of lines in the gaps that you

created. Make sure that the splines don’t overlap one another and fit nicely.

12

Step 13

Now change your viewport and drag these set of lines to the left or right, so that the curve would

be facing the opposite way of the other set of curves. *I felt like the oval gap it created between

my lines was a bit too much, so I selected both, and used the Scale tool to adjust it a bit.

13

Step 14

Remove the extra vertices that are created on the sides, making them both almost start and end at

the same points.

14

Step 15

Now we have created the basic pattern shape, so lets move on to some other details. Create two

Cylinders (Radius = 1; Height = 55) and place them side by side.

15

Step 16

Scale the two cylinders so that they look more like an oval shape rather than round.

Step 17

Group the two cylinders and call them “2 cylinders”.

16

Step 18

Move the group “2 cylinders”, and place them in the middle of the first gap in the splines you

created earlier. Feel free to scale the size of them, or edit the gap size of the overlapping lines to

allow your “2 cylinders” to fit nicely.

Step 19

Once you are satisfied with that, duplicate these “2 cylinders” across to fill all of the gaps by

holding down shift + drag.

17

Step 20

Group your pattern along with the “2 Cylinders” group, and call it it “Pattern.”

18

Step 21

Now to create a frame for the ‘Weaved Pattern’ and its details. Create a new Cylinder (Radius =

2.8; Height = 95).

19

Step 22

Hold down Shift, and rotate the Cylinder 90 degrees.

20

Step 23

Repeat this step by selecting both Cylinders, and rotating 180 degrees, and then adjusting the

cloned cylinders to make a square.

21

Step 24

Adjust the upper and lower cylinders to fit properly by lowering their radius and positioning

them correctly.

22

Step 25

Select all 4 cylinders, and convert to Editable Poly.

23

Step 26

Take the cylinder at the bottom, and move it upwards. This will create the base for your table

stand.

24

Step 27

Select the top border of your two side legs.

Step 28

Using the “Chamfer” tool, give it a “Chamfer Amount” of 3, and “Segments” of 3.

25

Step 29

In the Modifier List, apply the “Smooth” modifier, and check “Auto Smooth” in the option

panel.

26

Step 30

Make sure you can fit the “Pattern” you created earlier nicely inside the 4 borders you just

created. If not, then make the adjustments by raising the bottom cylinder.

27

Step 31

Group the 4 cylinders, along with your “Pattern”and call the whole thing “Side”.

28

Step 32

Select your group “Side”, and using the rotate tool, hold Shift and rotate by 90 degrees. Repeat

this step 3 more times to create a square shape. This will be the four sides of your table.

29

Step 33

Now that you have cloned your four sides, you will have four extra legs. Just delete them,

leaving you with a four sided table.

30

Step 34

Create a thin Box (Length = 94; Width = 94; Height = 3) at the top, this will be the glass. And

you’re done!

Sumber : http://cg.tutsplus.com/tutorials/autodesk-3d-studio-max/model-an-intricate-weaved-pattern-in-3ds-max/