07-1783-K Jackson 5pc faux marble dining set -...

OWNER’S MANUAL JACKSON 5PC FAUX MARBLE DINING SET

CAUTION: Read owner's manual completely before assembly and use.Product code: 0-06124818-3 UPC code: 729437124393 Date of purchase: / /

1

1. Use the long end of the Allen wrench to fasten Allen bolts loosely and quickly.

2. Use the short end of the Allen wrench for final tightening.

1. Chair-maximum load weight per chair is 300 pounds. 2. Table-maximum load weight on table top is 350 pounds.

1. Please read the assembly instructions prior to assembling this product. 2. To avoid damage, assemble this product on a non-abrasive surface such as carpet.

3. Make sure all bolts, nuts, and screws are tightly fastened before the product is used.

4. Not for commercial use.

5. Care: Wipe with a damp cloth. Use furniture polish or lemon oil on the wood as needed. Avoid prolonged exposure to moisture.

1 2

! WARNING: After a few days of initial assembly and chairs have acclimated to new

environment, retighten all hardware. Periodically check and retighten the screws every few months.

Please make sure you have all parts before beginning assembly. Please wait until all steps are

completed before tightening bolts, nuts, and screws. We recommend using two people for assembly.

G E N E R A L I N F O R M AT I O N & T I P S

M A X I M U M R E C O M M E N D E D W E I G H T C A PAC I T Y

A Phillips head screwdriver is necessary for assembly. It’s not included in hardware list.

2

Please do not return to the store. Contact VLG using the below information should you need to order any missing or replacement hardware. All parts except for the tabletop are replaceable.

A. Table Top – Not Replaceable B. Table Leg

QTY: 1 pc QTY: 4 pcs

1. Nut 2. Spring Washer 3. Flat Washer

QTY: 8 pcs QTY: 8 pcs QTY: 8 pcs

4. Open-End Wrench

QTY: 1 pc

PA R T S L I S T - Ta b l e

H A R DW A R E L I S T - Ta b l e

C U S TO M E R S E R V I C E I N F O R M AT I O N

Victory Land Group, Inc

1350 Munger Rd

Bartlett, IL 60103

WEB: http://www.victorylandgroup.com

PHONE: 1-800-933-0527

FAX: 1-630-540-7099

8:30 am to 5:00 pm CST, Mon. thru Fri.

EMAIL: help@victorylandgroup.com

3

Diagram #1

Diagram #2

A S S E M B LY I N S T R U C T I O N S - Ta b l e

A

B

B

B

B

A

4

1 2 3

1 2

3

Step 1 1. Place table top (A) upside down on a

non-abrasive surface such as carpet. 2. Attach table legs (B) to the table top (A)

using nuts (1) spring washers, (2) and flat washers (3) as shown.

Note: Do not tightly fasten the nuts at this step.

Step 2 3. Turn the table upright, making sure

the table is level. Tightly fasten all nuts using open-end wrench (4).

The Table is now ready for use.

4

C. Chair Seat D. Seat Frame E. Chair Back Frame

QTY: 4 pcs QTY: 4 pcs QTY: 4 pcs

F. Chair Leg

QTY: 8 pcs

1. Nut 2. Spring Washer 3. Flat Washer

QTY: 16 pcs QTY: 44 pcs QTY: 44 pcs

4. Open-End Wrench 5. Long Bolt 6. Short Bolt

1/4 Dia x 3-1/8 inch L 1/4 Dia x 1-5/8 inch L

QTY: 1 pc QTY: 16 pcs QTY: 12 pcs

7. Wood Screw 8. Allen Wrench

QTY: 24 pcs QTY: 1 pc

PA R T S L I S T - C h a i r

H A R D W A R E L I S T - C h a i r

5

Diagram #3

E

Step 1 1. Attach seat frame (D) to chair back frame (E) using spring washers (2), flat

washers (3), long bolts (5), and short bolts (6) as shown in inset (a) and (b). Note: Do not tighten the bolts at this step.

D

a

b

D

E

6 2 3

E 5

2 3

5 2

3

A S S E M B LY I N S T R U C T I O N S - C h a i r

8 6

6

2 2

3 3

8 D

a

b

6

Diagram #4

A S S E M B LY I N S T R U C T I O N S - C h a i r

Step 2 2. Attach chair legs (F) to the seat frame (D) using four nuts (1), four spring

washers (2) and four flat washers (3) as shown. Note: Do not tightly fasten the nuts at this step.

a

E

D

G

F

D 1 2 3

F

F

4

7

Diagram #5

A S S E M B LY I N S T R U C T I O N S - C h a i r

a

Step 3 4. Place chair seat (C) upside down on a non-abrasive table surface. The rear

(tapered end) on the chair seat (C) should be near the table edge. Hint: Protect the non-abrasive table surface and chair seat (C) by laying a towel

in-between the chair seat and table. 5. Place the assembled chair frame on the chair seat (C) as shown in inset (a).

Attach with six wood screws (7) as shown in inset (b). 6. Turn the chair upright. Make sure the assembled chair unit is level and square.

Tightly fasten all nuts and bolts with the open-end wrench (4) and Allen Wrench (8).

C D

F

C

D

7

F

E b

E C

8

Diagram #6

The Chair is now ready for use. Repeat diagram #3 to #6 to assemble the other chairs.

A S S E M B LY I N S T R U C T I O N S - C h a i r

9

Please refer to part numbers when reordering For questions or comments about product:

Email: help@victorylandgroup.com or Call toll-free: 1-800-933-0527

Made in / Hecho en VIETNAM for Kmart Corporation, Hoffman Estates, IL 60179

SHOP kmart.com