View
0
Download
0
Category
Preview:
Citation preview
© Copyright 2002 Printed
Great Plains Mfg., Inc.
Used with:
Installation Instructions
120-301M
No-Till andNo-Till Precision Seeding System
Veris Drive Option
• 3N-3010P and 3N-3020P
• 3N-3010 and 3N-3020
General Information
When you see this symbol, the subsequent instructions andwarnings are serious - follow without exception. Your life andthe lives of others depend on it!!!
These instructions explain how to install the VerisDrive Option. The Veris Drive is a precision popu-lation controller which uses a hydraulic drive toaccurately drive the metering system or the feed-er cups.
These instructions apply to:
120-298A Veris Drive Option
Manual UpdateRefer to the 30 No-Till or the 30P No-Till opera-tor’s manual for detailed information on safelyoperating, adjusting, troubleshooting and main-taining the Veris Drive. Refer to the parts manualfor part identification.
196-248M Operator’s Manual196-248P Parts Manual196-366M Operator’s Manual196-366P Parts Manual
3/26/2003
Before You StartPage 9 is a detailed listing of parts included in theVeris Drive Option package. Use this list to inven-tory parts received.
Tools Required• Basic Hand Tools
DefinitionsRight-hand and left-hand as used in this manualare determined by facing the direction themachine will travel while in use unless otherwisestated.
120-301M 4/8/2004
Great Plains Mfg., Inc.
Veris Drive Option2
! CAUTION!Before installing the Precision Population Controlleron the seeding system, be sure that the unit is properlysupported to avoid injury during installation.
Refer to Figure 1
1. Remove contact wheel drive chains on bothsides of the unit.
Refer to Figure 2
2. Remove range drive chains on both sides ofthe unit.
Refer to Figure 3
3. Drive out roll pins from drive couplers on bothends of the pivot shaft. Slide shaft couplerstoward the center and slide shaft throughtongue away from the left-hand drive.
Range Chain
Shaft Coupler
Pivot Shaft
Assembly Instructions
Figure 1Drive Chain Removed
20033
Figure 2Range Drive Chain
20034
Figure 3Pivot Shaft and Coupler
20035
Contact Drive WheelChain Removed
4/8/2004 120-301M
Great Plains Mfg., Inc.
3Installation Instructions
Refer to Figure 4
4. To mark and drill mounting holes for the con-troller/motor kit, use the dimensions suppliedon page 8. Mark the holes on the left-handtongue gusset on the mainframe and carefullydrill all four holes.
Note: It is important that you carefully mark anddrill these mounting holes. The lower portion ofthe drive mount houses the carrier bearing for thepivot shaft. Misalignment will cause operationalproblems.
Refer to Figure 5
5. Drill holes with either a 17/32” or 9/16” drill bit.
Place TemplateHere
17/32”Holes
Figure 4Hole Chart
Figure 5Left-hand Gusset
20036
20198
120-301M 4/8/2004
Great Plains Mfg., Inc.
Veris Drive Option4
Refer to Figure 6
6. Mount controller/motor kit to the gusset withfour flanged 1/2” x 1 1/4” bolts and 1/2”flanged lock nuts, do not tighten at this time.Leave hydraulic hoses and harness coiled un-til later in the assembly.
Refer to Figure 7
7. Slide the pivot shaft towards the installeddrive mount until shaft is a few inches throughthe bearing hanger. Slide on one lock collar,bearing and bearing flangettes. Install the 19tooth sprocket and second lock collar. Slideshaft back into position, then slide couplersback into position. Check to see if shaft is cen-tered in the bearing hanger opening. Looselyattach bearings flangettes, then tighten thefour mounting bolts on the controller/motor.Tighten bearing flangettes.
Note: Shaft should now turn freely by hand with nobinding at the shaft couplers. If this is not the case,the drive mount is not properly positioned on thegusset. To correct this, enlarge the mountingholes to allow the mount to be moved forward orbackward to properly align the mount with the piv-ot shaft.
Once the mount is properly aligned with the pivotshaft, reinstall the shaft couplers with 1/4” x 1 3/4”bolts and 1/4” lock nuts.
MountingBolts
Controller/Motor Kit
Pivot Shaft
Sprocket
Lock Collar
Bearing
Figure 6Controller/Motor
20037
Figure 7Pivot Shaft
20038
4/8/2004 120-301M
Great Plains Mfg., Inc.
5Installation Instructions
Refer to Figure 8
8. Slide the first lock collar installed on the pivotshaft against the bearing and tighten. Slidethe 19 tooth sprocket installed on the pivotshaft against the bearing. Slide the secondlock collar installed on the pivot shaft againstthe sprocket and tighten.
9. Install chain idler and chain.
Note: In order for the motor to have the correct ra-tio to the seed meters you must set the range andthe transmission sprockets.
Refer to Figure 9
10. For Precision drill:
Set the range sprockets with a 30 toothsprocket for the driver, and a 30 tooth sprock-et for the driven, on both sides of the unit. Re-install chains and tighten the idlers.
11. For Feeder Cup drill:
Set the range sprockets to drive type 4 onboth sides of the unit. Reinstall chains andtighten the idlers.
Refer to Figure 10
12. Set the transmission sprockets with a 28 toothsprocket for the driver, and a 25 tooth sprock-et for the driven, on both sides of the unit.
Note: Be sure to set both the left-hand and right-hand range and transmission sprockets. Oncethey are set they will not need to be changed.
Note: For Feeder Cup drill there is no transmis-sion sprocket change.
Idler
Figure 8Chain and Chain Idler
20039
Figure 9Range Sprockets
20040
Figure 10Transmission Sprockets
20041
120-301M 4/8/2004
Great Plains Mfg., Inc.
Veris Drive Option6
Refer to Figure 11
13. Remove the left wheel from the left-hand con-tact wheel shaft and slide the shaft to the rightallowing clearance for the speed sensor discand sensor bracket. Install the sensor bracketwith one bearing onto the shaft. Install thespeed sensor disc with one lock collar oneach side. Do not tighten lock collars.
14. Remove the forward bolt from the outsidebearing and replace it with a 5/16" x 1 3/4" boltand 5/16" nut and tighten. Place the spaceron the bolt then mount the sensor bracket onthe bolt. Secure bracket with a 5/16" nut.
15. Screw the sensor into the sensor mount untilthere is a .030 clearance. Lock sensor inplace with the jam nut. Move the sensor discso it aligns with the sensor and secure it inplace with the lock collars. Route the cablealong the contact wheel arm and up to thecontroller/motor mount. Repeat steps 13through 15 to install the Veris sensor and sen-sor bracket on the right-hand drive.
16. Relocate the seed monitor speed sensor tothe bracket installed on the left-hand drive.Properly adjust clearance. Tie both cables tothe contact wheel arm, and make sure theyare routed to prevent pinching.
Note: You can not leave the seed monitor speedsensor on the pivot shaft or the sensor will bereading motor drive speed instead of field speed.It is not necessary to move the sensor disc for theseed monitor. The seed monitor can use the samesensor disc as the Veris sensor.
Note: After relocating the seed monitor speedsensor it will be necessary to calibrate themonitor. Refer to the DICKEY-john® manualfor monitor distance calibration instructions.
Seed Sensor
Speed Sensor
Sensor Disc
Figure 11Speed Sensor and Bracket
Left-Hand Side
20042
Lock Collars
4/8/2004 120-301M
Great Plains Mfg., Inc.
7Installation Instructions
Refer to Figure 12
17. Connect sensor cable to short leads on sen-sor module. Either cable can be connected toeither lead.
18. Uncoil hydraulic hoses and main harness andtie ends together. Feed a fish tape or a wirefrom the front of the tongue and pull the hosesand cable through the main tongue and routethrough the hose carrier on front of thetongue.
19. Install the plastic hose label, P/N 817-348C,to hose with “extension” symbol on the hoserunning to filter (marked P) on control module.Use the yellow cable tie to identify this as amotor hose. Attach motor return hose(marked T) on the side showing the “retract”symbol. Run tie strap through number that willcorrespond to the valve 2 through 4 that thedrive will be connected to.
Refer to Figure 13
20. Install the console in a convenient location ona side window glass. Make sure the glass isclean. Moisten cups and press firmly onto theglass. To remove, pull tab on suction cup.
21. Connect power port adaptor cable to the ter-minal on the console.
22. Route the power and communication cablesthrough the cab access hole and connect tothe appropriate terminals on the console.
Sensor Module
CommunicationCable
Power PortAdapter
Serial Cable(for recipe input)
Figure 13Control Console
19977
Console
Figure 12Sensor Module
20043
120-301M 4/8/2004
Great Plains Mfg., Inc.
Veris Drive Option8
120-301M4/8/2004
Great Plains Mfg., Inc.
9Installation Instructions
120-298A PPC-30 Veris Vari-Rate DriveYour kit includes:
1 120-301M MANUAL INSTALL VERIS 30P2 120-309D SENSOR DISC, 42T 5.3 DIA P2 120-311D SENSOR U-MOUNT BRACKET1 136-182D CHAIN RL #50 50 PITCHES1 198-029D PARALLEL ARM PIVOT TUBE6 402-025S LOCK COLLAR, 7/8 HEX W/ SET SCREWS1 802-039C HHCS 1/2-13X3 GR53 802-159C HHCS 5/16-18X1 GR52 802-572C RHSNB 5/16-18X1 3/4 GR54 802-705C HHCS 5/16-18X5/84 803-011C NUT LOCK 5/16-18 PLT1 803-069C NUT HEX SLOTTED 7/16-14 PLT3 803-177C NUT HEX LOCK 5/16-18 FLG.3 804-017C WASHER FLAT 1/2 USS PLT4 804-036C WASHER FLAT 5/16 SAE PLT1 808-006C SPKT 50B19 X 1 BORE1 808-304C SPKT 50C19 X 7/8 HEX BORE1 808-341C SPKT 50B13 IDLER4 822-032C FLANGETTE 52 MST2 822-119C BRG.7/8HEX BR 52MM SPHRICAL2 822-175C FLANGETTE 52 3-BOLT PLT1 822-195C BRG.7/8HEX 52MM SPHR OD PE1 833-250C VERIS PPC-30 CONTROLLER
Qty. Part No. Part Description
Recommended