Blueprint jeopardy game

CONSTRUCTION MASTERS1 2 3 4 5 BONUS

6 7 8 9 10 BONUS

11 12 13 14 15 BONUS

16 17 18 19 20 BONUS

21 22 23 24 25 BONUS

The date that the drawing was checked or issued for construction is placed in the _____.

a. title blockb. legendc. borderd. key notes

A B C D

If symbols were not used on a drawing, workers would not be able to tell _____.a. the distance between walls b. location of the center of columnsc. detailed information about partsd. what material is required

A B C D

The definitions of any symbols or special marks used in a drawing are found in the _____.

a. scaleb. isometric drawingc. legendd. title block

A B C D

Lines drawn to indicate land boundaries on a drawing are called _____.

a. hidden linesb. section linesc. centerlinesd. property lines

A B C D

The exact location of a column on a drawing is shown by a(n) _____.

a. object lineb. cut linec. centerlined. break line

A B C D

A number or letter, usually with a leader and arrowhead, used to identify a specific object is a _____.

a. cut lineb. keynotec. gridline d. revision

A B C D

A building's roof framing plan is shown on the _____.

a. structural plansb. mechanical plansc. architectural plansd. detail plans

A B C D

The layout and dimensions of rooms, stairwells, doors, and mechanical equipment are shown on the _____.

a. floor plansb. detail drawingsc. mechanical plansd. cross sectional plans

A B C D

Specifications and locations of heating and cooling equipment and grilles and registers are shown on _____ plans.

a. architecturalb. plumbingc. mechanicald. structural

A B C D

The _____ shows the height of the side of a building.

a. plan viewb. elevation drawingc. detail drawingd. section drawing

A B C D

Tables that list the sizes and other types of information about doors and windows are found in the _____.

a. detail drawingsb. legendc. title blockd. finish schedules

A B C D

Structural plans include _____.a. notes about materials needed and

building requirementsb. notes about drainage and land usec. the schedule for finishing all surfacesd. the location of the electric meter and

distribution panel

A B C D

If the scale on an architectural plan is 1" = 10¨-0", then every _____.a. 1 inch on the plan equals 1/10 of a footb. 1 inch on the plan equals 10 feet, 0 inchesc. 10 feet on the plan equals 1 foot, 0 inchesd. 10 feet on the plan equals 1/10 of an inch

A B C D

Engineer's scales are used for _____.a. measuring areas too small to be measured by an architectural scaleb. locating structural beams and other

load-bearing surfacesc. plotting and working with survey and

site plansd. taking metric measurements

A B C D

NTS on architectural drawings means _____.

a. no template hereb. not to sizec. no trusses hered. not to scale

A B C D

What are plans called that have to do with construction in or on the earth?

a. civilb. architecturalc. structurald. specification

A B C D

To clarify any discrepancies in the plans, which of these should you use?

a. Indexb. legendc. HVACd. RFIA B C D

Where is information about the structure or assembly provided in a on a set of plans?

a. legendb. borderc. title boxd. drawing area

A B C D

Which of these is the project is identified by?

a. sheet titleb. company logoc. scaled. drawing number

A B C D

Which of these scales are used when developing site plans?

a. architect’sb. NTSc. engineersd. metric

A B C D

This form of an architect’s scale is commonly used because it contains a variety of scales

a. straight edgeb. ovalc. right angled. triangular

A B C D

What are the lines commonly used on a blueprint called?

a. collectionb. directoryc. alphabetd. language

A B C D

What do dimension lines end with?A. circlesb. squaresc. Xd. arrows

A B C D

Where should the symbols used on a set of blueprints should be located?

a. title sheetb. title blockc. legendd. scale

A B C D

A keynote is a number or letter that is often used instead of symbols and usually appears in _______.

A. block lettersb. a square or circlec. upper right cornerd. upper left corner

A B C D

BONUS 2A grid divides an area into small parts called _______.

a. squaresb. regionsc. baysd. pockets

A B C D

BONUS 4On a grid, the _____ are normally across the top and the ____ are across the side.

a. keynotes; numbersb. number; keynotesc. numbers; lettersd. letters; numbers

A B C D

BONUS 5

Which of the following letters does the gridline system omit?

a. U, V, W

b. M, N, H

c. I, J, T

d. I, O, QA B C D

BONUS 3The dimension is a measurement written as a __________.

a. keynote

b. number

c. letter

d. symbol

A B C D

BONUS 1On a blueprint, a dimension is located ______ the dimension line.

a. above

b. below

c. near the middle of

d. at the end of

A B C D

INCORRECT

CORRECT