View
1.061
Download
2
Category
Tags:
Preview:
DESCRIPTION
application of this project is to save enrgy by automatically switching the electrical appliances to conserve electrical energy
Citation preview
INTELLIGENT ENERGY SAVER
PREPAIRED BY:-
VYOMESH UPADHYAY
VIRESH SHUKLA
KRITESH SINGH
JITENDRA KU. VAISHY
UNDER THE GUIDENCE OF:-AMIT SHRIVASTVA(H.O.D)
Intelligent Energy Saving System can be used in
places like where lighting is very
important.
The libraries will be well
illuminated with many lamps.
When people are not present at a
reading place the lighting can be made OFF and when they are
present, the lighting made
ON.
All these can be done through by LDR circuit and
PIR sensor.
ABSTRACT
INDEXPrinciple of Operation
Electronic devices
PIR SensorMicrocontroller ATMega8L
LDR
Other ELEMENTS
HOW ITS WORK
CIRCUIT diagram
BLOCK Diagram
PROGRAMME
PINCIPLE OF OPERATION
This system mainly depends on PIR sensor, ATMega8l microcontroller & LDR(light depended resistor).
When the human are enter in room then PIR sensor sense the radiation emitted by body then sensor will be “ON” And gives the output 1 to the microcontroller
LDR is used to check the light intensity then if intensity is enough then it gives output 1 to microcontroller
Microcontroller is used to take logical decision after giving output by the PIR & LDR
DEVICES USED
PIR Sensor
ATMega 8A
LDR
7805,LM324,ULN-2003 Ics
Relays
LEDs and Resistors
Pot
PIR(pyro electric infrared sensor)• PIR sensors allow you to sense motion, almost always used to
detect whether a human has moved in or out of the sensors range
• PIRs are basically made of a pyro electric sensor which can detect levels of infrared radiation. The sensor in a motion detector is actually split in two halves. The reason for that is that we are looking to detect motion (change) not average IR levels
• When an intruder walks into the detector’s field of vision, the detector “sees” a sharp increase in infrared energy.
ATMega 8A
IT IS 28 PIN IC WHICH IS USED TO TAKE A LOGICAL DECISION
LDR LDR’s or Light Dependent Resistors are very useful especially
in light/dark sensor circuits. These help in automatically switching ON /OFF the street
lights and etc., normally the resistance of an LDR is very high, sometimes as very high as 1000000 ohms, but when they are illuminated with light, resistance drop dramatically.
Electronic opto sensors are the devices that alter their electrical characteristics, in the presence of visible or invisible light.
The best-known devices of these types are the light dependent resistor (LDR), the photo diode and the phototransistors.
OTHER ELEMENT
• IC 7805 : IC 7805 is a 5v voltage regulator that restricts the voltage output to 5v. It is a member of 78xx series of fixed linear voltage regulator ICs
FUNCTION NAMEPINNO
1
2
3
INPUT VOLTAGE(5V-18V)
GROUND(0V)
RAGULATED OUTPUT VOLTAGE;5V(4.8V-5.2)
INPUT
GND
OUTPUT
LM324:- LM324 is a 14pin IC consisting of four independent operational amplifiers (op-amps). These op-amps are operated by a single power supply LM324 and need for a dual supply is eliminated. They can be used as amplifiers, comparators, oscillators, rectifiers
ULN2003:-It is 16 pin IC. ULN2003 are high-voltage high-current Darlington transistor arrays. Each consists of seven npn Darlington pairs that feature high-voltage outputs. The output voltage is 50v and current 600mA.
RELAY
A relay is an electrically operated switch. Many relays use an electromagnet to operate switching operation mechanically.It is 5 terminal device consisting of 1 coil.When coil is enerzised then a slit is moves from one point to another point so circuit is completed and load starts works.
HOW ITS WORK Firstly we give the supply at the terminal then it goes to 7805 IC which converted into 5v.When any human body moves across the pir sensor then it senses its radiation and gives the output 1 to the microcontroller.At the same time LDR senses intensity of light(it can adjust by using of potentiometer). If intensity is low then it give output 0 to microcontr-oller. According to input microcontroller gives logical output 1 to the ULN2003.ULN2003 gives the output 0 to the relays, which energized the relays then loads workIf LDR senses enough intensity then it gives 1 to the microcontroller so it give another output causes on fan will be ON and bulb will be OFF.
CIRCUIT DIAGRAM
MICROCONTROLLERATMEGA 8A
PIR MOTION SENSOR
LDR CIRCUIT
FANLOAD
POWER SUPPLY
RELAY
RELAY
LAMP LOAD
BLOCK DIAGRAM
PROGRAMME:-#include <mega8.h>#include <delay.h>void pir();void pir1();void main(void){while (1){ int I;if(PINC.5==1) {pir(); } else { pir1(); //PORTB.2=0; //PORTB.3=0; }}}void pir(){if(PINC.4==0) {PORTB.2=1;PORTB.3=1;delay_ms(15000);} else { PORTB.2=0;PORTB.3=1;delay_ms(15000);} } void pir1() {int i;for(i=0;i<=1;i++) {if(PINC.5==1) {pir();break;} else {delay_ms(100); } if(i==1) {PORTB.1=0;PORTB.2=0;delay_ms(15000); }} }
Recommended