TABLE OF CONTENTS
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2What is Scanning? . . . . . . . . . . . . . . . . . . . . . . . . . . . 2What is Searching? . . . . . . . . . . . . . . . . . . . . . . . . . . 2Types of Communications . . . . . . . . . . . . . . . . . . . . . 3
Feature Highlights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Where to Obtain More Information . . . . . . . . . . . . . . . . . 5Included with Your Scanner. . . . . . . . . . . . . . . . . . . . . . . 6Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Installing the Batteries . . . . . . . . . . . . . . . . . . . . . . . . 7AC Adapter/Charger . . . . . . . . . . . . . . . . . . . . . . . . . . 8Charging Warning. . . . . . . . . . . . . . . . . . . . . . . . . . . . 8Adapter Safety Feature . . . . . . . . . . . . . . . . . . . . . . . 9Flexible Antenna. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9Belt Clip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Basic Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10Setting the Squelch . . . . . . . . . . . . . . . . . . . . . . . . . 10Keylock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13Duplicate Frequency Alert . . . . . . . . . . . . . . . . . . . . 14Programming Tips . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Scanning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16Channel Lockout. . . . . . . . . . . . . . . . . . . . . . . . . . . . 17Lockout in Manual Mode . . . . . . . . . . . . . . . . . . . . . 17Locking a Channel While Scanning . . . . . . . . . . . . . 18Lockout Tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18Restore a Locked Out Channel . . . . . . . . . . . . . . . . 19Restore All Locked-out Channels . . . . . . . . . . . . . . . 20
Priority Scan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21Changing the Priority Channel . . . . . . . . . . . . . . . . . 22
Chain Search . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23Setting a Search Range . . . . . . . . . . . . . . . . . . . . . . 23Search Hold Feature . . . . . . . . . . . . . . . . . . . . . . . . 26Channel Skip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27Storing Search Frequencies . . . . . . . . . . . . . . . . . . . 27
Weather Scan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30Care and Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . 31
General Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31Repairs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32Birdies. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34Accessories and Replacement Parts. . . . . . . . . . . . . . . 35One Year Limited Warranty . . . . . . . . . . . . . . . . . . . . . . 36
1
Introduction
The BC60XLT-1 Scanner is a sophisticated informationradio that allows you to monitor 10 different frequencybands and the NOAA weather information broadcasts. It isa state-of-the-art radio with scanning capabilities, and itcan save up to 30 different frequencies in memory.
What is Scanning?
Unlike standard AM or FM radio stations, most two-waycommunications do not transmit continuously. TheBC60XLT-1 scans programmed channels until it finds anactive frequency.
Scanning stops on an active frequency and remains onthat channel as long as the transmission continues. Whenthe transmission ends, the scanning cycle resumes untilanother transmission is received.
What is Chain Searching?
You can program five different personal search bands inyour new scanner. You simply select a Chain Searchlocation, define the search range, and begin your search.The scanner looks for active communications in the rangeyou’ve specified, so you can locate frequencies in yourarea which may not be listed in your Betty Bearcat StarterFrequency Guide.
You can set your scanner to search up to all five ChainSearch bands at once, or you can turn off those searchbands you don’t want. This gives you complete control ofthe search function.
H:\TEMP\Bc60xlt-1 Intr pg.vpThu Jul 20 09:27:23 2000
Color profile: DisabledComposite Default screen
Types of Communications
Monitor communications such as:
Police and fire department (including rescue andparamedics)
NOAA weather broadcasts (preprogrammedchannels)
Business/industrial radio
Motion picture and press relay
Utilities
Land transportation frequencies, such as truckingfirms, buses, taxis, tow trucks, and railroads
Marine and amateur (ham radio) bands
And more in these bands:
FrequencyRange
Transmission
29-29.7 MHz 10 Meter Amateur Band
29.7-50 MHz VHF Low Band
50-54 MHz 6 Meter Amateur Band
137-144 MHz Military Land mobile
144-148 MHz 2 Meter Amateur Band
148-174 MHz VHF High Band
406-420 MHz Federal Govt. Land Mobile
420-450 MHz 70 cm Amateur Band
450-470 MHz UHF Standard Band
470-512 MHz UHF “T” Band
3
Feature Highlights
30 Channels – Program one frequency into eachchannel. You must have at least one channelprogrammed to use the Scan mode.
29 MHz-512 MHz – Search these frequencyranges with your scanner. (The frequencycoverage is not totally continuous from 29 MHz to512 MHz.)
Chain Searching – You can define five differentpersonal search bands, and search up to all fivechain locations at once.
Priority Channel Scanning – Allows you todesignate a priority channel which is monitoredevery two seconds when Priority Scanning isselected.
Manual Channel Access – Go directly to anychannel.
Memory Backup – Frequencies programmed inchannels are retained in memory. If power iscompletely disconnected, the frequencies areretained for one hour.
Weather Scan – Use as a weather informationradio.
Preset Two-second Delay – Scanner waits twoseconds after transmission stops before resumingscanning.
LCD Back Light – An orange LCD light remainson for 15 seconds when l is pressed.
4
Where to Obtain MoreInformation
Before using your scanner, you must program frequenciesinto available channels. The Betty Bearcat StarterFrequency Guide lists typical frequencies used around theU.S.A. and Canada that you may program into your newscanner.
If the frequencies listed in the starter guide do not work inyour area, call the enclosed Mr. Scanner (800) Number. AUniden representative should be able to provide you withsample frequencies, or use the enclosed order form topurchase a local frequency list.
The Bearcat Radio Club and other similar hobby clubshave publications, information on computer bulletin boards,and even contests for the radio enthusiast. Also, your locallibrary has more information.
5
Included with Your Scanner
If any of these items are missing or damaged, immediatelycontact your place of purchase or Uniden CustomerService at: (800) 297-1023, 8:00 a.m. to 5:00 p.m., Central,Monday through Friday.
Rubber Antenna(AT218)
Belt ClipwithScrews(BCK150)
AC Adapter(AD70U)
Betty BearcatStarter
FrequencyGuide
OtherPrintedMaterial
6
Setup
These are helpful guidelines when using your new scanner:
If your scanner receives interference or electricalnoise, move the scanner or its antenna away fromthe source.
If you need to improve reception, use an optionalantenna designed for multi-band coverage.(Youcan purchase this type of antenna at a localelectronics store.)
Use the included earphone or an optional stereoheadset with proper impedance for privatelistening. Read the precautions on the inside frontcover of this Guide.
Installing the Batteries
1. Open the cover.
2. Insert batteries.
Note: If you are installing alkaline batteries, set the switchto REG. ALK. BATT. If installing Nickel-CadmiumBatteries, set the switch to Ni-Cd BATT.
Press in
Lift
Ni-CdBATT.
REG.ALK.BATT.
Ni-CdBATT.
REG.ALK.BATT.
Insideof TopCover
7
3. Replace cover andpress down until itclicks into place.
Warning: Do not mix alkaline batteries with Ni-CdBatteries. Be sure to install four batteries ofthe same type.
AC Adapter/Charger
Use the AC Adapter/Charger to power the BC 60XLT-1from an AC outlet.
Charging Warning
Do not charge alkaline batteries in this scanner. Doing somay cause serious damage to the product and void thewarranty. Before attempting to recharge batteries, makesure you have installed four rechargeable nickel-cadmiumbatteries and the selector switch is set to Ni-Cd BATT .
Ni-CdBATT.
REG.ALK.BATT.
AC 120VOutlet
AD-70UAC Adapter
Use only the supplied AC Adapter(AD70U) or one of the optional power
cords (UA502 or UA510).
8
Adapter Safety Feature
The AC Adapter included with this scanner may beequipped with a polarized line plug — a plug with oneblade wider than the other. This plug will fit into the poweroutlet only one way. If you are unable to insert the plugfully into the outlet, try reversing the plug.
Flexible Antenna
Belt Clip
Attach the flexible antenna to theBNC connector.
Do not tighten the screws too tight.You can damage the case or clip.
9
Basic Operation
Note: You can fold out the Front Cover to see theControls and Indicators while reading this Guide.
Setting the Squelch
To set the Squelch, you must be in the Manual Mode. Nosignal should be present when adjusting squelch.
1. Press Muntilyou do not hear asignal.
2. Adjust VOLUME to acomfortable listeninglevel.
3. Think of the Squelch Control as a gate. TurnSQUELCH fully counter-clockwise. This raises the“Squelch Gate” so high that no signals can getthrough.
Strong Signals
Medium Signals
Weak Signals
Noise
PHONE SQUELCH VOLUME
10
4. Turn SQUELCH fully clockwise until you hear a hiss.This lowers the “Squelch Gate” so that everythinggets through—noise, weak signals, and strongsignals.
5. Turn SQUELCH back counter-clockwise just until thehiss stops. Now the “Squelch Gate” allows onlystrong signals through.
Strong Signals
Medium Signals
Weak Signals
Noise
PHONE SQUELCH VOLUME
Strong Signals
Medium Signals
Weak Signals
Noise
PHONE SQUELCH VOLUME
11
Keylock
Key Lock prevents accidental key entries during scanning.
1. To lock the keypad,press and hold Kuntil the key symbolappears.
2. To unlock the keypad,press and hold Kuntil the key symboldisappears.
12
Programming
Before the BC 60XLT -1 can receive radio broadcasts, youmust program a frequency into at least one channel.Before scanning, repeat this procedure for each channelyou program.
1. Select frequenciesfrom your starterguide.
2. Press M.
3. Select a channel.a. Enter the channel
number.b. Then press M
.
13
4. Enter the frequency.a. Enter the frequency
number.b. Then press E.
Note: To clear a mistake while entering the frequency,press B twice, and start over.
If the frequency entered is outside the Frequency Range ofthe scanner, a distinctive beep sounds. (See the Table onpage 3 or the Band List on the back of the scanner).
Press and goback to Step 4.
Duplicate Frequency Alert
If you enter afrequency stored inanother channel, youhear a beep and theother channelappears in the display.
Press to startagain
—OR—
Press again tostore the frequency inboth channels.
SCANMHz
HOLD PRI L/O WX SEARCHP 2 CH
14
Programming Tips
Do not program a weather frequency into one ofthe channels, since weather channels transmitcontinuously. Use for weather information.
Group similar frequencies into adjacent channels.For example, program police frequencies inchannels 1 through 10 and fire/emergency intochannels 11 through 20, and so on.
Put the frequency that you listen to the most or themost important frequency into a Priority channel.
To quickly program a series of channels, start withthe lowest number channel. For example, whenyou are programming five new frequencies intoChannels 4 through 8, start with Channel 4. Afteryou finish programming a channel, press or
to go to the next higher channel.
To erase the channel, press , and then press. Channels with no frequencies are
automatically locked out.
Record channels and frequencies in someconvenient place in case the scanner memory islost.
15
Scanning
When you turn on thepower, theBC60XLT-1automatically starts inthe Scan mode.
During normalscanning the scannerskips unprogrammedor locked outchannels.
When a transmissionis received, theScanner stops on thatchannel. When thetransmission ends,scanning resumesautomatically aftertwo seconds.
To stop on a channelduring scanning,press .
To resume scanning,press .
1 3 4 5 9 102 6 7 8CHANNELS
Frequen cy notentered
Frequen cyLocked Out
(L/O)
SCAN
16
Channel Lockout
You can lockout any channel so it is not reviewed duringnormal scanning. You can restore the channel to scanningwhenever you wish.
Lockout in Manual Mode
1. Press .
2. Select a channel.a. Enter the channel
number.b. Then press
again.
3. Press to lockoutthe channel.
17
Locking a Channel While Scanning
If the scanner keeps stopping on a particular channel dueto noise or too frequent transmissions, you may want tokeep that channel from scanning.
1. Wait until the scannerstops at the channel.
2. Then press .
3. The scannerimmediately resumesscanning because thelocked out channel isno longer in thescanning sequence.
Lockout Tips
To quickly lockout a series of channels, start withthe lowest number channel.
For example, if you are locking out channels 4, 7,8, 12, and 15, start with Channel 4. After selectingchannel 4, press . Then press one ormore times to step up to the next channel to belocked out.
Record the locked-out channels in someconvenient place so you can restore them.
18
Restore a Locked Out Channel
1. Press .
2. Select a locked outchannel.
a. Enter the channelnumber.
b. Then pressagain.
3. Press to unlockthe channel.
19
Restore All Locked-out Channels
1. Press .
Note: You must be inManual Mode beforerestoring alllocked-out channels.
2. Press and holdfor about two seconds.
You will hear twobeeps when all thechannels have beenrestored.
20
Priority Scan
When Priority Scan is turned on, your scanner checks thepriority channel every two seconds for activity. If a signal ispresent on the priority channel, your scanner monitors thechannel until the transmission ends, then resumes normalscanning. You can designate any of the 30 availablechannels as your Priority Channel.
To activate Priority Scan (in either Manual or Scan Mode):
1. Press .
Note: If you havelocked out the prioritychannel, thismessage appearswhen you selectPriority Mode.
2. Press again atanytime to deactivatePriority Scan.
21
Changing the Priority Channel
You cannot eliminate the Priority Channel, but you canchange it to any other of the 30 available channels.
1. Press .
2. Select a new PriorityChannel.
a. Enter the channelnumber.
b. Then pressagain.
3. Press and holdfor two seconds todesignate thischannel as your newPriority Channel.
Two beeps indicatethat the PriorityChannel is changed.
22
Chain Search
Use Chain Search to find active frequencies in your area.You can search up to all five personal bands or turn offthose bands you don’t want to hear. This gives youflexibility of searching for any channel between 29 and 512MHz, as long as they are within the 10 frequencies bandscovered by the BC60XLT-1. See the table on page 3, theTechnical Specifications on page 34, or the table on theback of the BC60XLT-1.
Setting a Search Range
An error messagedisplays when R ispressed and youhave not eitherspecified a searchrange in at least oneChain Search band
—OR—
If you attempt to turnoff all Personal ChainSearch bands.
The Error messageturns off automaticallyand Chain 1 isselected when allsearch locations areempty. Press Mto return to normalscan, or press s toselect the band youwant to program.
23
To program a frequency range into one of the five personalChain Search bands, follow these steps:
1. Press s until thesearch location youwant appears in thedisplay.
2. Enter lower limit ofthe search band.
a. Enter the frequencynumber.
b. Then press E.
Note: The displayalternates betweenthe upper and lowerranges.
3. Enter upper limit ofthe search band.
a. Enter the frequencynumber.
b. Then press E.
24
Note: The displayalternates betweenthe upper and lowerranges. If youprogram the wronglimit, press 0 andE, then press 0and E again toerase the error andreset the limits tozero. Then beginagain.
4. Either press R tobegin your search.
Note: Your scanner searches each selectedPersonal Chain Search band. The display flashesthe number of the band while it’s scanned. Otherbands which are programmed and selected aredisplayed but do not flash.
—OR—
Press s to move tothe next chainlocation.
Note: You can press the Chain Search bandnumber, followed by s, to access the locationdirectly.
25
5. To turn off a ChainSearch band duringsearch scanning,press its locationnumber.
For example, (a) ifChain Searchlocations 1, 2 and 3are selected, (b)press 3 to turn offband three so that it’snot scanned duringyour search.
Search Hold Feature
1. Press U or D atanytime to stop thesearch.
2. Press U to move tothe next higherfrequency
—OR—(See Step 3)
3. Press D to movedown to the previousfrequency.
4. Press R to resumesearching.
Note: The searchcontinues towardeither the upper orlower search limit,depending on whichdirection key (U orD ) was pressed last.
26
Channel Skip
If a particular channel continues to interrupt searchscanning, it is possible to set your scanner to skip thefrequency.
If your scanner stopswhile searching,press N to lockoutthe frequency fromthe search range.
Note: You canprogram 10 skipfrequencies. The 11thskip frequencyentered causes the1st skip frequency tounlock.
To unlock all skip frequencies at once, follow these steps:
1. Press either U orDduring a search.
Note: You must be inSearch Hold beforerestoring all skippedfrequencies.
2. Press and hold Nfor about two seconds.
You will hear twobeeps when all thechannels have beenrestored.
Storing Search Frequencies
You can quickly store any frequency you find duringSearch.
Caution: You must select the channel in which you willstore the frequency before entering the searchmode. Otherwise, you may erase a storedfrequency that you want to keep.
27
1. Press M.
2. Select a channel.a. Enter the channel
number.b. Then press M
again.
3. Select one or more ofthe personal searchbands.
For example, selectCHAIN 2.
Note: Thesefrequencies wereused during “Setting aSearch Range,” onpage 23.
4. Press R .
5. When the scannerstops at thefrequency you want,press either U orD .
28
Note: After this stepyou are in SearchHold mode. Press Rto resume scanning.
6. Press E to store thefrequency in thechannel you selected.
Note: After this stepyou are in manualmode.
Repeat steps 2 through 6 for all the Search frequenciesyou want to store.
Note: Remember that there are only 30 channelsavailable to store frequencies, whether youprogram them directly or while using the ChainSearch mode.
29
Weather Scan
Your BC60XLT-1 is designed to scan 7 programmedNOAA frequencies, so you easily find your local NOAAweather broadcast.
Note: It is not advisable to program a weather frequencyinto one of the 30 channels since weatherchannels transmit continuously. The scanner willremain on the weather channel, disrupting thescanning cycle.
1. Press W to activatethe Weather scan.
Note: Be sureSQUELCH is setproperly.
2. When the WeatherScan finds an activeweather channel, itstops.
3. Press W again tofind the next activeweather channel.
Note: In some parts of the country, you may not be ableto monitor weather broadcasts, such as inlow-lying areas. Normally, a higher location or abetter antenna improves reception.
4. To exit WeatherScan, press M,S, or R.
30
Care and Maintenance
General Use
Turn the scanner off before disconnecting thepower or replacing the batteries.
Always write down the programmed frequencies inthe event of memory loss.
If memory is lost, simply reprogram each channel.The display shows 000.0000 in all channels whenthere has been a memory loss.
Always press each button firmly until you hear theentry tone for that key entry.
Location
Do not use the scanner in high-moistureenvironments such as the kitchen or bathroom.
Avoid placing the unit in direct sunlight or nearheating elements or vents.
If the scanner receives strong interference orelectrical noise, move it or its antenna away fromthe source of the noise. If possible, a higherelevation, may provide better reception. Also trychanging the height or angle of the antenna.
Do not plug the scanner into an outlet controlled bya wall switch because long power interruptionsmay cause memory loss.
Cleaning
Disconnect the power to the unit before cleaning.
Clean the outside of the scanner with a milddetergent. To prevent scratches, do not useabrasive cleaners or solvents. Be careful not to rubthe LCD window.
Do not use excessive amounts of water.
31
Repairs
Do not attempt any repair. The scanner containsno serviceable parts. Contact the UnidenCustomer Service Center or take it to a qualifiedrepair technician.
Birdies
All radios can receive “birdies” (undesired signals).If your scanner stops during Scan mode and nosound is heard, it may be receiving a birdie. Birdiesare internally generated signals inherent in theelectronics of the receiver.
Press L to lockout the channel,and then pressSto resume scanning.
32
Troubleshooting
If your BC60XLT-1 is not performing properly, try thefollowing steps.
Problem Suggestion
Scanner won’t work. 1. Check the connections at both ends ofthe AC Adapter.
2. Turn on the wall switch of your room. Youcould be using an outlet controlled by thewall switch.
3. Move the AC Adapter to another walloutlet or replace the batteries.
Improper reception. 1. Check the antenna connection or moveand reposition the antenna.
2. Move the scanner.
3. You may be in a remote area which couldrequire an optional multi-band antenna.Check with your dealer or localelectronics store.
Scan won’t stop. 1. Adjust squelch threshold - refer topage 10, Setting the Squelch.
2. Check the antenna connection.
3. Check to see if many of the channels arelocked out. If so, the scanner has lesschance of finding an active channel.
4. Review each channel’s frequency to seeif it is still stored in memory and is correct.
5. It’s possible that none of the programmedfrequencies are currently active.
Scan won’t start. 1. Press the Skey again.
2. Adjust the SQUELCH control.
3. Check to see if all channels are lockedout.
Weather Scan won’t work. 1. Adjust squelch threshold - refer topage 10, Setting the Squelch.
2. Check the antenna.
If you still cannot get satisfactory results and wantadditional information, or to return the unit for service,please call or write the Uniden Parts and Service Division.The address and phone number are listed in the Warrantyat the end of this manual, or call 1-800-297-1023.
33
Specifications
Certified in accordance with FCC Rules and RegulationsPart 15, Subpart C, as of date of manufacture.
Channels: 30 (1 Bank)
WX: 7 NOAA Weather Service Channels
Search Bands: 10 Preprogrammed Bands5 Programmable Chain Search
Bands
Frequency Range: 29.0–29.7 MHz 10 Meter Amateur Band29.7–50 MHz VHF Low Band50–54 MHz 6 Meter Amateur Band137–144 MHz Military Land Mobile144–148 MHz 2 Meter Amateur Band148–174 MHz VHF High BandAbove bands in 5 kHz steps
406–420 MHz Federal Government420–450 MHz 70 cm Amateur Band450–470 MHz UHF Standard Band470–512 MHz UHF “T” BandAbove bands in 12.5 kHz steps
OperatingTemperature:
–20°C to +60°C
Scan Rate: 10 Channels per second
Search Rate: 10 Steps per second
Scan Delay: 2 seconds
Audio Output: 18 mW nominal into 8Ω internal speaker3 mW nominal into 32Ω stereo headphone8 mW nominal into 64Ω earphone
PowerRequirements:
12VDC using AD70U Adapter or4AA Alkaline or rechargeableNickel-Cadmium Batteries
Antenna: Rubber antenna (included)
External Jacks: External earphone, DC 12V power jack
Size: 21⁄2 in. (W) x 11⁄2 in. (D) x 7 in. (H)
Weight: 12 oz.
Features, Specifications, and availability of optionalaccessories are all subject to change without notice.
34
Accessories and ReplacementParts
Rubber Antenna(AT218)
Belt ClipwithScrews(BCK150)
AC Adapter(AD70U)
Monaural Earphone64
(EP009)Ω
Cigarette LighterPower Cord
(UA502)
Hard-Wired Power Cord(UA510)
Betty BearcatStarter
FrequencyGuide
35
One Year Limited Warranty
Important: Evidence of original purchase is required forwarranty service.
WARRANTOR: UNIDEN AMERICA CORPORATION (“Uniden”)ELEMENTS OF WARRANTY: Uniden warrants, for one year, tothe original retail owner, this Uniden Product to be free fromdefects in materials and craftsmanship with only the limitations orexclusions set out below.WARRANTY DURATION: This warranty to the original user shallterminate and be of no further effect 12 months after the date oforiginal retail sale. The warranty is invalid if the Product is (A)damaged or not maintained as reasonable or necessary, (B)modified, altered, or used as part of any conversion kits,subassemblies, or any configurations not sold by Uniden, (C)improperly installed, (D) serviced or repaired by someone otherthan an authorized Uniden service center for a defect ormalfunction covered by this warranty, (E) used in any conjunctionwith equipment or parts or as part of any system notmanufactured by Uniden, or (F) installed or programmed byanyone other than as detailed by the Operating Guide for thisproduct.STATEMENT OF REMEDY: In the event that the product doesnot conform to this warranty at any time while this warranty is ineffect, warrantor will repair the defect and return it to you withoutcharge for parts, service, or any other cost (except shipping andhandling) incurred by warrantor or its representatives inconnection with the performance of this warranty. THE LIMITEDWARRANTY SET FORTH ABOVE IS THE SOLE AND ENTIREWARRANTY PERTAINING TO THE PRODUCT AND IS IN LIEUOF AND EXCLUDES ALL OTHER WARRANTIES OF ANYNATURE WHATSOEVER, WHETHER EXPRESS, IMPLIED ORARISING BY OPERATION OF LAW, INCLUDING, BUT NOTLIMITED TO ANY IMPLIED WARRANTIES OFMERCHANTABILITY OR FITNESS FOR A PARTICULARPURPOSE. THIS WARRANTY DOES NOT COVER ORPROVIDE FOR THE REIMBURSEMENT OR PAYMENT OFINCIDENTAL OR CONSEQUENTIAL DAMAGES. Some statesdo not allow this exclusion or limitation of incidental orconsequential damages so the above limitation or exclusion maynot apply to you.LEGAL REMEDIES: This warranty gives you specific legal rights,and you may also have other rights which vary from state tostate. This warranty is void outside the United States of America.PROCEDURE FOR OBTAINING PERFORMANCE OFWARRANTY : If, after following the instructions in this OperatingGuide you are certain that the Product is defective, pack theProduct carefully (preferably in its original packaging). Includeevidence of original purchase and a note describing the defectthat has caused you to return it. The Product should be shippedfreight prepaid, by traceable means, or delivered, to warrantor at:
Uniden America CorporationParts and Service Division4700 Amon Carter BoulevardFort Worth, TX 76155(800) 297-1023, 8:00 a.m. to 5:00 p.m., Central, Mondaythrough Friday
36
Covered under one or more of the following U.S. patents:
RE31,523 4,027,251 4,057,760 4,092,594 4,100,497
4,114,103 4,123,715 4,156,193 4,157,505 4,179,662
4,219,821 4,270,217 4,398,304 4,409,688 4,455,679
4,461,036 4,521,915 4,627,100 4,888,815 4,932,074
4,947,456 5,014,348 5,199,109
©1995 Uniden America Corporation. All rights reserved.Printed in the Philippines
Recommended
