Download pdf - Sound Processor Series for Car Audio Sound Processors … · volume, loudness, 5ch fader volume, LPF for subwoofer(except ... built-in 3-band equalizer filter, LPF for subwoofer

1/37 www.rohm.com 2010.03 - Rev.A

© 2010 ROHM Co., Ltd. All rights reserved.

Sound Processor Series for Car Audio

Sound Processors with Built-in 3-band Equalizer BD37531FV,BD37532FV,BD37533FV,BD37534FV

Description

BD37531FV, BD37532FV, BD37533FV, BD37534FV are sound processors built-in 3-band equalizer for car audio. The

functions are stereo input selector available to switch single end input and ground isolation input, input-gain control, main

volume, loudness, 5ch fader volume, LPF for subwoofer(except BD37531FV), mixing input(except BD37531FV,

BD37532FV). Moreover, “Advanced switch circuit”, that is ROHM original technology, can reduce various switching noise

(ex. No-signal, low frequency likes 20Hz & large signal inputs). “Advanced switch” makes control of microcomputer easier,

and can construct high quality car audio system.

Features 1) Reduce switching noise of input gain control, mute, main volume, fader volume, bass, middle, treble, loudness

by using advanced switch circuit [Possible to control all steps] 2) Built-in differential input selector that can make various combination of single-ended / differential input. 3) Built-in ground isolation amplifier inputs, ideal for external stereo input. 4) Built-in input gain controller reduces switching noise for volume of a portable audio input. 5) Decrease the number of external components by built-in 3-band equalizer filter, LPF for subwoofer (except BD37531FV),

loudness filter. And, possible to control Q, Gv, fo of 3-band equalizer and fc of LPF, Gv of loudness by I2C BUS control freely

6) It is possible for the bass, middle, treble to the gain adjustment quantity of ±20dB and 1 dB step gain adjustment. 7) Terminals for the subwoofer outputs are equipped, and the audio signal outputs of front, back and subwoofer can be

chosen with the I2C BUS control. 8) Built-in mixing input, mixing attenuator. (except BD37531FV, BD37532FV) 9) Bi-CMOS process is suitable for the design of low current and low energy. And it provides more quality for small

scale regulator and heat in a set. 10) Package is SSOP-B28. Putting input-terminals together and output-terminals together can make PCB layout easier and

can makes area of PCB smaller. 11) It is possible to control by 3.3V / 5V for I2C BUS.

Applications It is the optimal for the car audio. Besides, it is possible to use for the audio equipment of mini Compo, micro Compo, TV etc with all kinds.

No.10085EAT06

Technical Note

2/37

BD37531FV,BD37532FV,BD37533FV,BD37534FV

www.rohm.com 2010.03 - Rev.A© 2010 ROHM Co., Ltd. All rights reserved.

Line up matrix

Function BD37531FV BD37532FV BD37533FV BD37534FV Specifications

Input selector

・(Stereo input) ・Single-End/Diff/Full-Diff (Possible to set the number of single-end/diff/full-diff as follows )

Single-End Differential Full-Differential Mode 1 0 3 1 Mode 2 1 2 1 Mode 3 3 1 1 Mode 4 4 0 1 Mode 5 5 1 0 Mode 6 6 0 0

Table.1 Combination of input selector

Input gain

・0～20dB（1dB step）・Possible to use “Advanced switch” for prevention of switching

noise.

Mute ・Possible to use “Advanced switch” for prevention of switching

noise.

Volume ・+15dB～-79dB（1dB step）, -∞ ・Possible to use “Advanced switch” for prevention of switching

noise.

Bass

・-20～+20dB（1dB step）・Q=0.5, 1, 1.5, 2 ・fo=60, 80, 100, 120Hz ・Possible to use “Advanced switch” at changing gain

Middle

・-20～+20dB（1dB step）・Q=0.75, 1, 1.25, 1.5 ・fo=500, 1k, 1.5k 2.5kHz ・Possible to use “Advanced switch” at changing gain

Treble

・-20～+20dB（1dB step）・Q=0.75, 1.25 ・fo=7.5k, 10k, 12.5k, 15kHz ・Possible to use “Advanced switch” at changing gain

Fader

・+15dB～-79dB(1dB step), -∞dB (BD37531FV : 0dB～-79dB, -∞dB)

・Possible to use “Advanced switch” for prevention of switching noise.

Loudness

・0dB～20dB(1dB step) ・fo=250/400/800Hz ・Possible to use “Advanced switch” for prevention of switching

noise.

LPF × ・fc=55/85/120/160Hz, pass ・Phase shift (0°/180°)

Mixing × ×

・Monaural input ・+7dB～-79dB（1dB step）, -∞ ・Possible to use “Advanced switch” for prevention of switching

noise. Level meter

× × × ・I2C BUS control ・DC Output

Technical Note

3/37



Absolute maximum ratings (Ta=25)

※This value decreases 8.5mW/ for Ta=25 or more. ROHM standard board shall be mounted. Thermal resistance θja = 117.6(/W) ROHM Standard board

Size：70×70×1.6() Material：A FR4 grass epoxy board(3% or less of copper foil area)

Operating conditions

Item Symbol MIN TYP MAX Unit

Power supply Voltage VCC 7.0 － 9.5 V

Temperature Topr -40 － +85

Item Symbol Rating Unit

Power supply Voltage VCC 10.0 V

Input voltage Vin VCC+0.3～GND-0.3 V

Power Dissipation Pd 1063 ※1 mW

Storage Temperature Tastg -55～+150

Technical Note

4/37



Electrical characteristics (Unless specified particularly, Ta=25, VCC=8.5V, f=1kHz, Vin=1Vrms, Rg=600Ω, RL=10kΩ, A1 input, Input gain 0dB, Mute off, Volume 0dB, Tone control 0dB, Loudness 0dB, LPF OFF(BD37532FV,BD37533FV,BD37534FV), Mixing OFF(BD37533FV,BD37534FV), Fader 0dB)

BLOCK

Item SymbolLimit

Unit Condition Min. Typ. Max.

GENERAL

Current upon no signal IQ － 38 48 mA No signal Voltage gain GV -1.5 0 1.5 dB Gv=20log(VOUT/VIN) Channel balance CB -1.5 0 1.5 dB CB = GV1-GV2 Total harmonic distortion 1 (FRONT,REAR)

THD+N1 － 0.001 0.05 ％ VOUT=1Vrms BW=400-30KHz

Total harmonic distortion 2 (SUBWOOFER)

THD+N2 － 0.002 0.05 ％ VOUT=1Vrms BW=400-30KHz

Output noise voltage 1 (FRONT,REAR)＊

VNO1 － 3.8 15 μVrmsRg = 0Ω BW = IHF-A

Output noise voltage 2 (SUBWOOFER)＊

VNO2 － 4.8 15 μVrmsRg = 0Ω BW = IHF-A

Residual output noise voltage＊ VNOR － 1.8 10 μVrmsFader = -∞dB Rg = 0Ω BW = IHF-A

Cross-talk between channels＊ CTC － -100 -90 dB Rg = 0Ω CTC=20log(VOUT/VIN) BW = IHF-A

Ripple rejection RR － -70 -40 dB f=1kHz VRR=100mVrms RR=20log(VCC IN/VOUT)

INPUT SELECTOR

Input impedance(A, B, C) RIN_S 70 100 130 kΩ Input impedance (D, E) RIN_D 175 250 325 kΩ

Maximum input voltage VIM 2.1 2.3 － Vrms VIM at THD+N(VOUT)=1％ BW=400-30KHz

Cross-talk between selectors CTS － -100 -90 dB Rg = 0Ω CTS=20log(VOUT/VIN) BW = IHF-A

Common mode rejection ratio ＊ (D, E) CMRR 50 65 － dB

XP1 and XN input XP2 and XN input CMRR=20log(VIN/VOUT) BW = IHF-A,[※X・・・D,E]

INPUT GAIN Minimum input gain GIN MIN -2 0 +2 dB

Input gain 0dB VIN=100mVrms Gin=20log(VOUT/VIN)

Maximum input gain GIN MAX +18 +20 +22 dB Input gain +20dB VIN=100mVrms Gin=20log(VOUT/VIN)

Gain set error GIN ERR -2 0 +2 dB GAIN=+20～+1dB

MUTE

Mute attenuation＊ GMUTE － -105 -85 dB Mute ON Gmute=20log(VOUT/VIN) BW = IHF-A

VOLUME

Maximum gain GV MAX 13 15 17 dB Volume = 15dB VIN=100mVrms Gv=20log(VOUT/VIN)

Maximum attenuation＊ GV MIN － -100 -85 dB Volume = -∞dB Gv=20log(VOUT/VIN) BW = IHF-A

Attenuation set error 1 GV ERR1 -2 0 2 dB GAIN & ATT=+15dB～-15dBAttenuation set error 2 GV ERR2 -3 0 3 dB ATT=-16dB～-47dBAttenuation set error 3 GV ERR3 -4 0 4 dB ATT=-48dB～-79dB

Technical Note

5/37



BLOCK

Item SymbolLimit


BASS

Maximum boost gain GB BST 18 20 22 dB Gain=+20dB f=100Hz VIN=100mVrms GB=20log (VOUT/VIN)

Maximum cut gain GB CUT -22 -20 -18 dB Gain=-20dB f=100Hz VIN=2Vrms GB=20log (VOUT/VIN)

Gain set error GB ERR -2 0 2 dB Gain=-20～+20dB f=100Hz

MIDDLE

Maximum boost gain GM BST 18 20 22 dB Gain=+20dB f=1kHz VIN=100mVrms GM=20log (VOUT/VIN)

Maximum cut gain GM CUT -22 -20 -18 dB Gain=-20dB f=1kHz VIN=2Vrms GM=20log (VOUT/VIN)

Gain set error GM ERR -2 0 2 dB Gain=-20～+20dB f=1kHz

TREBLE

Maximum boost gain GT BST 17 20 23 dB Gain=+20dB f=10kHz VIN=100mVrms GT=20log (VOUT/VIN)

Maximum cut gain GT CUT -23 -20 -17 dB Gain=-20dB f=10kHz VIN=2Vrms GT=20log (VOUT/VIN)

Gain set error GT ERR -2 0 2 dB Gain=-20～+20dB f=10kHz

MIXING

(BD37533FV,BD37534FV)

Input impedance RIN_M 19 27 35 kΩ

Maximum input voltage VIM_M 2.0 2.2 － VrmsVIM at THD+N(VOUT)=1％ BW=400-30KHz

Maximum attenuation GMX MIN － -100 -85 dB MIX=OFF GMX=20log(VOUT/VIN) BW=INF-A

Maximum gain GMX MAX 5 7 9 dB ATT=+6dB GMX=20log(VOUT/VIN)

FADER / SUBWOOFER

Maximum boost gain (BD37532FV,BD37533FV,BD37534FV)

GF BST 13 15 17 dB Fader=15dB VIN=100mVrms GF=20log(VOUT/VIN)

Maximum attenuation＊ GF MIN － -100 -90 dB Fader = -∞dB GF=20log(VOUT/VIN) BW = IHF-A

Gain set error (BD37532FV,BD37533FV,BD37534FV)

GF ERR -2 0 2 dB Gain=+1～+15dB

Attenuation set error 1 GF ERR1 -2 0 2 dB ATT=-1～-15dB



Output impedance ROUT - － 50 Ω VIN=100mVrms

Maximum output voltage VOM 2 2.2 － VrmsTHD+N=1％ BW=400-30KHz

LOUDNESS

Maximum gain GL MAX 17 20 23 dB Gain 20dB VIN=100mVrms GL=20log(VOUT/VIN)

Gain set error GL ERR -2 0 2 dB GAIN=+20～+1dB

Level meter

(BD37534FV)

Maximum output voltage VL MAX 2.8 3.1 3.5 V

Output offset voltage VL OFF - 0 100 mV

VP-9690A(Average value detection, effective value display) filter by Matsushita Communication is used for ＊ measurement.

Phase between input / output is same.

Technical Note

6/37



Electrical characteristic curves (Reference data)

-25-20

-15-10-50

51015

2025

10 100 1k 10k 100k

-25-20-15-10-505

10152025

10 100 1k 10k 100k

-25-20-15

-10-505

10

152025

10 100 1k 10k 100kFrequency [Hz]

Ga

in[d

B]

0.001

0.01

0.1

1

10

0.001 0.01 0.1 1 10

Vout (V)

THD+N (%

0.001

0.01

0.1

1

10

Vou

TH

D+

N[%

] Vout [Vrms]

Vin

[Vrm

s]

-25-20

-15-10-50

51015

2025


Ga

in[d

B]

0

10

20

30

40

50

0 2 4 6 8 10

VCC[V]

Iq[m

A]

-25-20

-15-10-50

51015

2025

10 100 1k 10k 100k

Frequency [Hz]

Ga

in[d

B]

Frequency [Hz]

Ga

in[d

B]

-25

-20

-15

-10

-50

5

10

15

20

25

10 100 1k 10k 100k

Frequency (Hz)

Gai

n (d

B)

Ga

in[d

B]

-25

-20

-15

-10

-5

0

5

10

15

20

25

10 100 1k 10k 100k

Frequency (Hz)

Gai

n (d

B)

Ga

in[d

B]

-25

-20

-15

-10

-5

0

5

10

15

20

25

10 100 1k 10k 100k

Ga

in[d

B]

Fig.12 Gain vs Freq

Frequency [Hz] Frequency [Hz] Frequency [Hz]

-25-20-15-10-505

10152025


Ga

in[d

B]

-5

-4

-3

-2

-10

1

2

3

4

5

10 100 1k 10k 100k

Frequency (Hz)

Gai

n (d

B

Ga

in[d

B]

Frequency [Hz]

10kHz

1kHz

100Hz Gain=0dB

BASS GAIN : -20～+20dB /1dB step fo : 60Hz Q : 0.5

Q : 0.5/1/1.5/2 BASS GAIN : ±20dB fo : 60Hz

fo : 60/80/100/120Hz BASS GAIN : ±20dB Q : 0.5

fo : 500/1k/1.5k/2.5kHz

MIDDLE GAIN : ±20dB fo : 500Hz

Q : 0.75/1/1.25/1.5MIDDLE GAIN : -20～+20dB /1dB step

fo : 500Hz Q : 0.75

Frequency [Hz]

Ga

in[d

B]

TREBLE GAIN:-20～+20dB /1dB step fo : 7.5kHz Q : 0.75

Q : 0.75/1.25 TREBLE GAIN : ±20dB fo : 7.5kHz

fo : 7.5k/10k/12.5k/15kHz TREBLE GAIN : ±20dB Q : 0.75

Fig.6 Bass Q vs Freq

Fig.8 Middle fo vs Freq Fig.9 Middle Q vs Freq

Fig.1 Iq vs Vcc

Fig.10 Treble Gain vs Freq Fig.11 Treble fo vs Freq Fig.12Treble Q vs Freq

Fig.5 Bass fo vs Freq

Fig.2 Thd vs Vo Fig.3 Gain vs Freq

Fig.4 Bass Gain vs Freq

Fig.7 Middle Gain vs Freq

Technical Note

7/37



1

10

100

1000

-80 -70 -60 -50 -40 -30 -20 -10 0 10 20

Volume Gain[dB]

出力

雑音

電圧

[uV

rms] Din-Audio IHF-A

-70

-60

-50

-40

-30

-20

-10

0

10 100 1k 10k 100k

Frequency (Hz)

Gai

n (d

B

0

0.5

1

1.5

2

2.5

3

3.5

0 0.5 1 1.5 2 2.5 3

1

10

100

1000

-20 -15 -10 -5 0 5 10 15 20Treble Gain [dB]

出力

雑音

電圧

[uV

rms] DIN-Audio IHF-A

1

10

100

1000

-20 -15 -10 -5 0 5 10 15 20

Bass Gain [dB]

出力

雑音

電圧

[uV

rms] DIN-Audio IHF-A

1

10

100

1000

-20 -15 -10 -5 0 5 10 15 20Middle Gain [dB]

出力

雑音

電圧

[uV

rms]

DIN-Audio IHF-A

Vin [Vrms]

Vo

ut[

V]

0.0

0.5

1.0

1.5

2.0

2.5

100 1000 10000 100000

出力負荷[ohm]

最大

出力

[Vrm

s]

Frequency [Hz]

Ga

in[d

B]

Fig.16 Treble Gain vs Noise

Fig.20 Advanced Switch 2 Fig.21 Level Meter Vin vs Vo

Fig.13 Volume Gain vs Noise Fig.15 Middle Gain vs Noise

Fig.18 Rload vs Vo

Fig.14 Bass Gain vs Noise

Fig.17 CMRR vs Freq

Fig.21 : Level Meter function is available only BD37534FV

Fig.19 Advanced Switch 1

Ou

tpu

t N

ois

e[u

Vrm

s]

Ou

tpu

t N

ois

e[u

Vrm

s]

Ou

tpu

t N

ois

e[u

Vrm

s]

Ou

tpu

t N

ois

e[u

Vrm

s]

Rload [ohm]

Vo

[V

rms]

Technical Note

8/37



Block diagram and pin configuration

Fig.22 BD37531FV

Descriptions of terminal Terminal

No. Terminal Name

Description Terminal

No. Terminal Name

Description

1 A1 A input terminal of 1ch 15 MUTE External compulsory mute terminal

2 A2 A input terminal of 2ch 16 TEST2 Test Pin

3 B1 B input terminal of 1ch 17 TEST3 Test Pin

4 B2 B input terminal of 2ch 18 OUTS2 Subwoofer output terminal of 2ch

5 C1 C input terminal of 1ch 19 OUTS1 Subwoofer output terminal of 1ch

6 C2 C input terminal of 2ch 20 OUTR2 Rear output terminal of 2ch

7 DP1 D positive input terminal of 1ch 21 OUTR1 Rear output terminal of 1ch

8 DN D negative input terminal 22 OUTF2 Front output terminal of 2ch

9 DP2 D positive input terminal of 2ch 23 OUTF1 Front output terminal of 1ch

10 EP1 E positive input terminal of 1ch 24 VCC Power supply terminal

11 EN1 E negative input terminal of 1ch 25 SCL I2C Communication clock terminal

12 EN2 E negative input terminal of 2ch 26 SDA I2C Communication data terminal

13 EP2 E positive input terminal of 2ch 27 GND GND terminal

14 TEST1 Test Pin 28 FIL VCC/2 terminal

GNDVCC/2

28 27 26 25 24 23 22 21 20 19 18 17 16 15

Volume/Mute

3 Band P-EQ(Tone control)

Loudness

Fad

er

Fad

er

Fad

er

Fad

er

Fad

er

Input Gain

GNDISO amp

Input selector (3 single-end and 2 stereo ISO)

1 2 3 4 5 6 7 8 9 10 11 12 13 14

100k 100k 100k 100k 100k 100k 250k

GNDISO amp

250k250k

GNDISO amp

250k 250k

GNDISO amp

250k 250k

VCC

I2C BUS LOGIC

Fader Gain:0dB～-79ｄB/1dB step

no pop noiseLoudness Gain:20dB～0ｄB/1ｄB step

no pop noise・ｆ0=250/400/800Hz・Hicut1/2/3/4

3 Band P-EQ (Tone control) Gain：+20dB～-20dB/1dB step

no pop noise・Bass：f0=60/80/100/120Hz

Q=0.5/1.0/1.5/2.0・Meddle:f0=500/1k/1.5k/2.5kHz

Q=0.75/1/1.25/1.5・Treble：f0=7.5k/10k/12.5k/15kHz

Q=0.75/1.25Volume Gain：+15dB～-79dB/1dB step

no pop noiseInput Gain Gain：+20dB～0dB/1dB step

no pop noise

Technical Note

9/37



Fig.23 BD37532FV


No. Terminal Name


No. Terminal Name

Description














14 TEST1 Test Pin 28 FIL VCC/2 terminal

GNDVCC/2

28 27 26 25 24 23 22 21 20 19 18 17 16 15

Volume/Mute


Loudness

Fad

er

Fad

er

Fad

er

Fad

er

Fad

er

LPF

Input Gain

GNDISO amp


1 2 3 4 5 6 7 8 9 10 11 12 13 14

100k 100k 100k 100k 100k 100k 250k

GNDISO amp

250k250k

GNDISO amp

250k 250k

GNDISO amp

250k 250k

VCC

I2C BUS LOGIC

Fader Gain:+15dB～-79ｄB/1dB step

no pop noiseLPF fc=55/85/120/160HzLoudness Gain:20dB～0ｄB/1ｄB step




Q=0.5/1.0/1.5/2.0・Meddle:f0=500/1k/1.5k/2.5kHz

Q=0.75/1/1.25/1.5・Treble：f0=7.5k/10k/12.5k/15kHz



no pop noise

Technical Note

10/37



Fig.24 BD37533FV


No. Terminal Name


No. Terminal Name

Description














14 MIN Mixing input terminal 28 FIL VCC/2 terminal

GNDVCC/2

28 27 26 25 24 23 22 21 20 19 18 17 16 15

Volume/Mute


Loudness

Fad

er

Fad

er

Fad

er

Fad

er

Fad

er

LPF

Input Gain

ATT

GNDISO amp


1 2 3 4 5 6 7 8 9 10 11 12 13 14

100k 100k 100k 100k 100k 100k 250k

GNDISO amp

250k250k

GNDISO amp

250k 250k

GNDISO amp

250k 250k

VCC

I2C BUS LOGIC






Q=0.5/1.0/1.5/2.0・Meddle:f0=500/1k/1.5k/2.5kHz

Q=0.75/1/1.25/1.5・Treble：f0=7.5k/10k/12.5k/15kHz



no pop noise

Technical Note

11/37



Fig.25 BD37534FV


No. Terminal Name


No. Terminal Name

Description


2 A2 A input terminal of 2ch 16 LRST Level meter reset terminal

3 B1 B input terminal of 1ch 17 LOUT Output terminal for Level meter











14 MIN Mixing input terminal 28 FIL VCC/2 terminal

GNDVCC/2

28 27 26 25 24 23 22 21 20 19 18 17 16 15

Volume/Mute


Loudness

Fad

er

Fad

er

Fad

er

Fad

er

Fad

er

LPF

Input Gain

ATT

GNDISO amp


1 2 3 4 5 6 7 8 9 10 11 12 13 14

100k 100k 100k 100k 100k 100k 250k

GNDISO amp

250k250k

GNDISO amp

250k 250k

GNDISO amp

250k 250k

Level meter

VCC

I2C BUS LOGIC






Q=0.5/1.0/1.5/2.0・Meddle:f0=500/1k/1.5k/2.5kHz

Q=0.75/1/1.25/1.5・Treble：f0=7.5k/10k/12.5k/15kHz



no pop noise

Technical Note

12/37



Timming Chart

CONTROL SIGNAL SPECIFICATION

(１) Electrical specifications and timing for bus lines and I/O stages

Fig.26 Definition of timing on the I2C-bus

Table 1 Characteristics of the SDA and SCL bus lines for I2C-bus devices (Unless specified particularly, Ta=25, VCC=8.5V)

Parameter Symbol Fast-mode I2C-bus

UnitMin. Max.

1 SCL clock frequency ｆSCL 0 400 kHz

2 Bus free time between a STOP and START condition tBUF 1.3 － μS

3 Hold time (repeated) START condition. After this period, the first

clock pulse is generated tHD;STA 0.6 － μS

4 LOW period of the SCL clock tLOW 1.3 － μS

5 HIGH period of the SCL clock tHIGH 0.6 － μS

6 Set-up time for a repeated START condition tSU;STA 0.6 － μS

7 Data hold time: tHD;DAT 0.06* － μS

8 Data set-up time tSU;DAT 120 － ns

9 Set-up time for STOP condition tSU;STO 0.6 － μS

All values referred to VIH min. and VIL max. Levels (see Table 2).

* A device must internally provide a hold time of at least 300 ns for the SDA signal (referred to the VIH min. of the SCL

signal) in order to bridge the undefined region of the falling edge of SCL. About 7(tHD;DAT), 8(tSU;DAT), make it the setup which a margin is fully in .

SDA

S

SCL

tLOW tR

tHD;DAT

P

tHD;STA tHIGH

tBUF tF

tSU;DAT tSU;STAtSU;STO

tSP tHD;STA

Sr

P

Technical Note

13/37



Table 2 Characteristics of the SDA and SCL I/O stages for I2C-bus devices

Parameter Symbol Fast-mode devices

UnitMin. Max.

10 LOW level input voltage: VIL -0.3 1 V

11 HIGH level input voltage: VIH 2.3 5 V

12 Pulse width of spikes which must be suppressed by the input filter. tSP 0 50 ns

13 LOW level output voltage: at 3mA sink current VOL1 0 0.4 V

14 Input current each I/O pin with an input voltage between 0.4V and

4.5V. Ii -10 10 μA

Fig.27 A command timing example in the I2C data transmission

ｔBUF：4us

ｔHD;STA：2us

ｔHD;DAT：1us

ｔLOW：3us

ｔHIGH：1us

ｔSU;DAT：1us

ｔSU;STO：2us

SCL clock frequency：250kHz

SCL

SDA

Technical Note

14/37



（２）I2C BUS FORMAT

MSB LSB MSB LSB MSB LSB

S Slave Address A Select Address A Data A P

1bit 8bit 1bit 8bit 1bit 8bit 1bit 1bit

S = Start conditions (Recognition of start bit)

Slave Address = Recognition of slave address. 7 bits in upper order are voluntary.

The least significant bit is “L” due to writing.

A = ACKNOWLEDGE bit (Recognition of acknowledgement)

Select Address = Select every of volume, bass and treble.

Data = Data on every volume and tone.

P = Stop condition (Recognition of stop bit)

（３）I2C BUS Interface Protocol

1）Basic form

S Slave Address A Select Address A Data A P

MSB LSB MSB LSB MSB LSB

2）Automatic increment (Select Address increases (+1) according to the number of data.

S Slave Address A Select Address A Data1 A Data2 A ････ DataN A P

MSB LSB MSB LSB MSB LSB MSB LSB MSB LSB

（Example）①Data1 shall be set as data of address specified by Select Address.

②Data2 shall be set as data of address specified by Select Address +1.

③DataN shall be set as data of address specified by Select Address +N-1.

3）Configuration unavailable for transmission (In this case, only Select Address1 is set.

S Slave Address A Select Address1 A Data A Select Address 2 A Data A P

MSB LSB MSB LSB MSB LSB MSB LSB MSB LSB

（Note）If any data is transmitted as Select Address 2 next to data, it is

recognized as data, not as Select Address 2.

（４）Slave address

MSB LSB

A6 A5 A4 A3 A2 A1 A0 R/W

1 0 0 0 0 0 0 0 80H

Technical Note

15/37



（５）Select Address & Data

BD37531FV

Items Select Address (hex)

MSB Data LSB

D7 D6 D5 D4 D3 D2 D1 D0

Initial setup 1 01 Advanced switch ON/OFF

0 Advanced switch time of Input Gain/VolumeTone/Fader/Loudness

0 1 Advanced switch time

of Mute

Initial setup 2 02 0 0 Subwoofer Output

Select 0 0 0 0

Initial setup 3 03 0 0 0 Loudness fo 0 0 1

Input Selector 05 Full-diff

Type 0 0 Input selector

Input gain 06 Mute

ON/OFF 0 0 Input Gain

Volume gain 20 Volume Gain / Attenuation

Fader 1ch Front 28 Fader Attenuation

Fader 2ch Front 29 Fader Attenuation

Fader 1ch Rear 2A Fader Attenuation

Fader 2ch Rear 2B Fader Attenuation

Fader Subwoofer 2C Fader Attenuation

Test Mode 30 1 1 1 1 1 1 1 1

Bass setup 41 0 0 Bass fo 0 0 Bass Q

Middle setup 44 0 0 Middle fo 0 0 Middle Q

Treble setup 47 0 0 Treble fo 0 0 0 Treble Q

Bass gain 51

Bass

Boost/

Cut

0 0 Bass Gain

Middle gain 54

Middle

Boost/

Cut

0 0 Middle Gain

Treble gain 57

Treble

Boost/

Cut

0 0 Treble Gain

Loudness Gain 75 0 Loudness Hicut Loudness Gain

System Reset FE 1 0 0 0 0 0 0 1

Advanced switch

Note

１．In function changing of the hatching part, it works Advanced switch.

２．Upon continuous data transfer, the Select Address is circulated by the automatic increment function, as shown below.

３．For the function of input selector and subwoofer output select etc, it is not corresponded for advanced switch. Therefore, please apply mute on the side of a set when changes these setting.

４．When using mute function of this IC at the time of changing input selector, please switch mute ON/OFF for waiting

advanced-mute time.

→01→02→03→05→06→20→28→29→2A→2B→2C

→30→41→44→47→51→54→57→75

Technical Note

16/37



BD37532FV


MSB Data LSB

D7 D6 D5 D4 D3 D2 D1 D0


0 Advanced switch time of Input Gain/VolumeTone/Fader/Loudness


of Mute

Initial setup 2 02 LPF

Phase 0

Subwoofer Output

Select 0 Subwoofer LPF fc




Input gain 06 Mute



Fader 1ch Front 28 Fader Gain / Attenuation


Fader 1ch Rear 2A Fader Gain / Attenuation

Fader 2ch Rear 2B Fader Gain / Attenuation

Fader Subwoofer 2C Fader Gain / Attenuation

Test Mode 30 1 1 1 1 1 1 1 1




Bass gain 51

Bass

Boost/

Cut

0 0 Bass Gain

Middle gain 54

Middle

Boost/

Cut

0 0 Middle Gain

Treble gain 57

Treble

Boost/

Cut

0 0 Treble Gain



Advanced switch

Note


２．Upon continuous data transfer, the Select Address is circulated by the automatic increment function, as

shown below.



advanced-mute time.

→01→02→03→05→06→20→28→29→2A→2B→2C

→30→41→44→47→51→54→57→75

Technical Note

17/37



BD37533FV


MSB Data LSB

D7 D6 D5 D4 D3 D2 D1 D0


0

Advanced switch time of Input Gain/VolumeTone/Fader/Loudness

/Mixing


of Mute


Phase 0

Subwoofer Output





Input gain 06 Mute








Mixing 30 Mixing Gain / Attenuation




Bass gain 51

Bass

Boost/

Cut

0 0 Bass Gain

Middle gain 54

Middle

Boost/

Cut

0 0 Middle Gain

Treble gain 57

Treble

Boost/

Cut

0 0 Treble Gain



Advanced switch

Note



shown below.



advanced-mute time.

→01→02→03→05→06→20→28→29→2A→2B→2C

→30→41→44→47→51→54→57→75

Technical Note

18/37



BD37534FV


MSB Data LSB

D7 D6 D5 D4 D3 D2 D1 D0


0

Advanced switch time of Input Gain/VolumeTone/Fader/Loudness

/Mixing


of Mute


Phase

Level

Meter

RESET

Subwoofer Output





Input gain 06 Mute








Mixing 30 Mixing Gain / Attenuation




Bass gain 51

Bass

Boost/

Cut

0 0 Bass Gain

Middle gain 54

Middle

Boost/

Cut

0 0 Middle Gain

Treble gain 57

Treble

Boost/

Cut

0 0 Treble Gain



Advanced switch

Note



shown below.



advanced-mute time.

→01→02→03→05→06→20→28→29→2A→2B→2C

→30→41→44→47→51→54→57→75

Technical Note

19/37



Select address 01 (hex)

Time MSB Advanced switch time of Mute LSB

D7 D6 D5 D4 D3 D2 D1 D0

0.6msec Advanced

Switch

ON/OFF

0

Advanced switch time

of Input gain/Volume

Tone/Fader/Loudness

/Mixing

0 1

0 0

1.0msec 0 1

1.4msec 1 0

3.2msec 1 1

(Mixing is available only BD37533FV, BD37534FV)

Time MSB

Advanced switch time of Input

gain/Volume/Tone/Fader/Loudness/Mixing LSB

D7 D6 D5 D4 D3 D2 D1 D0

4.7 msec Advanced

Switch

ON/OFF

0

0 0

0 1 Advanced switch

Time of Mute

7.1 msec 0 1

11.2 msec 1 0

14.4 msec 1 1


Mode MSB Advanced switch ON/OFF LSB

D7 D6 D5 D4 D3 D2 D1 D0

OFF 0

0

Advanced switch time

of Input gain/Volume

Tone/Fader/Loudness

/Mixing

0 1 Advanced switch

Time of Mute ON 1


Select address 02(hex)

fc MSB Subwoofer LPF fc LSB

D7 D6 D5 D4 D3 D2 D1 D0

OFF

LPF Phase

Level

Meter

RESET

Subwoofer Output

Select 0

0 0 0

55Hz 0 0 1

85Hz 0 1 0

120Hz 0 1 1

160Hz 1 0 0

Prohibition Other setting

(Available only BD37532FV, BD37533FV, BD37534FV)

Mode MSB Subwoofer Output Select LSB

D7 D6 D5 D4 D3 D2 D1 D0

LPF

LPF Phase

Level

Meter

RESET

0 0

0 Subwoofer LPF fc Front 0 1

Rear 1 0

Prohibition 1 1

Mode MSB Level Meter RESET LSB

D7 D6 D5 D4 D3 D2 D1 D0

HOLD LPF Phase

0 Subwoofer output

select 0 Subwoofer LPF fc

RESET 1

(Available only BD37534FV)

Phase MSB LPF Phase LSB

D7 D6 D5 D4 D3 D2 D1 D0

0° 0 Level

Meter

RESET

Subwoofer output

select 0 Subwoofer LPF fc

180° 1

(Available only BD37532FV, BD37533FV, BD37534FV) : Initial Condition

Technical Note

20/37




f0 MSB Loudness fo LSB

D7 D6 D5 D4 D3 D2 D1 D0

250Hz

0 0 0

0 0

0 0 1 400Hz 0 1

800Hz 1 0

Prohibition 1 1


Mode MSB Input Selector LSB

OUTF1 OUTF2 D7 D6 D5 D4 D3 D2 D1 D0

A A1 A2

Full-di

ff bias

type

select

0 0

0 0 0 0 0

B B1 B2 0 0 0 0 1

C C1 C2 0 0 0 1 0

D single DP1 DP2 0 0 0 1 1

E1 single EP1 EN1 0 1 0 1 0

E2 single EN2 EP2 0 1 0 1 1

A diff A1 B1 0 1 1 1 1

C diff B2 C2 1 0 0 0 0

D diff DP1 DP2 0 0 1 1 0

E full diff EP1 EP2 0 1 0 0 0

Input SHORT 0 1 0 0 1

Prohibition Other setting

Input SHORT： The input impedance of each input terminal is lowered from 100kΩ(TYP) to 6 kΩ(TYP).

(For quick charge of coupling capacitor)

Mode MSB Full-diff Bias Type Select LSB

D7 D6 D5 D4 D3 D2 D1 D0

Negative Input 0 0 0 0

Input

Selector

Bias 1

: Initial condition

Negative input type For Ground – isolation type)

Bias type

For differential amplifier type

1ch Differential

10

EP1

11

EN1

12

EN2

13

EP22ch

Differential

1ch Differential

2ch Differential

10

EP1

11

EN1

12

EN2

13

EP2

1ch signal input

2ch signal input

1ch signal input

2ch signal input

Technical Note

21/37




Gain MSB Input Gain LSB

D7 D6 D5 D4 D3 D2 D1 D0

0dB

Mute

ON/OFF 0 0

0 0 0 0 0

1dB 0 0 0 0 1

2dB 0 0 0 1 0

3dB 0 0 0 1 1

4dB 0 0 1 0 0

5dB 0 0 1 0 1

6dB 0 0 1 1 0

7dB 0 0 1 1 1

8dB 0 1 0 0 0

9dB 0 1 0 0 1

10dB 0 1 0 1 0

11dB 0 1 0 1 1

12dB 0 1 1 0 0

13dB 0 1 1 0 1

14dB 0 1 1 1 0

15dB 0 1 1 1 1

16dB 1 0 0 0 0

17dB 1 0 0 0 1

18dB 1 0 0 1 0

19dB 1 0 0 1 1

20dB 1 0 1 0 0

Prohibition

1 1 0 1 1

：：：：：

1 1 1 1 1

Mode MSB Mute ON/OFF LSB

D7 D6 D5 D4 D3 D2 D1 D0

OFF 0 0 0 Input Gain

ON 1

: Initial condition

Technical Note

22/37



Select address 20, 28, 29, 2A, 2B, 2C (hex)

Gain & ATT MSB Vol, Fader Gain / Attenuation LSB

D7 D6 D5 D4 D3 D2 D1 D0

Prohibition

0 0 0 0 0 0 0 0

0 0 0 0 0 0 0 1

：：：：：：：：

0 1 1 1 0 0 0 0

15dB 0 1 1 1 0 0 0 1

14dB 0 1 1 1 0 0 1 0

13dB 0 1 1 1 0 0 1 1

：：：：：：：：：

-77dB 1 1 0 0 1 1 0 1

-78dB 1 1 0 0 1 1 1 0

-79dB 1 1 0 0 1 1 1 1

Prohibition

1 1 0 1 0 0 0 0

：：：：：：：：

1 1 1 1 1 1 1 0

-∞dB 1 1 1 1 1 1 1 1

(About BD37531FV, only 0dB～-∞dB are available)


Gain & ATT MSB Mixing Gain / Attenuation LSB

D7 D6 D5 D4 D3 D2 D1 D0

Prohibition

0 0 0 0 0 0 0 0

0 0 0 0 0 0 0 1

：：：：：：：：

0 1 1 1 1 0 0 0

7dB 0 1 1 1 1 0 0 1

6dB 0 1 1 1 1 0 1 0

5dB 0 1 1 1 1 0 1 1

：：：：：：：：：

-77dB 1 1 0 0 1 1 0 1

-78dB 1 1 0 0 1 1 1 0

-79dB 1 1 0 0 1 1 1 1

Prohibition

1 1 0 1 0 0 0 0

：：：：：：：：

1 1 1 1 1 1 1 0

MIX OFF 1 1 1 1 1 1 1 1

(Available only BD37533FV, BD37534FV)

: Initial condition

Technical Note

23/37




Q factor MSB Bass Q factor LSB

D7 D6 D5 D4 D3 D2 D1 D0

0.5

0 0 Bass fo 0 0

0 0

1.0 0 1

1.5 1 0

2.0 1 1

fo MSB Bass fo LSB

D7 D6 D5 D4 D3 D2 D1 D0

60Hz

0 0

0 0

0 0 Bass

Q factor

80Hz 0 1

100Hz 1 0

120Hz 1 1


Q factor MSB Middle Q factor LSB

D7 D6 D5 D4 D3 D2 D1 D0

0.75

0 0 Middle fo 0 0

0 0

1.0 0 1

1.25 1 0

1.5 1 1

fo MSB Middle fo LSB

D7 D6 D5 D4 D3 D2 D1 D0

500Hz

0 0

0 0

0 0 Middle

Q factor

1kHz 0 1

1.5kHz 1 0

2.5kHz 1 1


Q factor MSB Treble Q factor LSB

D7 D6 D5 D4 D3 D2 D1 D0

0.75 0 0 Treble fo 0 0 0

0

1.25 1

fo MSB Treble fo LSB

D7 D6 D5 D4 D3 D2 D1 D0

7.5kHz

0 0

0 0

0 0 0 Treble

Q factor

10kHz 0 1

12.5kHz 1 0

15kHz 1 1

: Initial condition

Technical Note

24/37



Select address 51, 54, 57 (hex)

Gain MSB Bass/Middle/Treble Gain LSB

D7 D6 D5 D4 D3 D2 D1 D0

0dB

Bass/

Middle/

Treble

Boost

/cut

0 0

0 0 0 0 0

1dB 0 0 0 0 1

2dB 0 0 0 1 0

3dB 0 0 0 1 1

4dB 0 0 1 0 0

5dB 0 0 1 0 1

6dB 0 0 1 1 0

7dB 0 0 1 1 1

8dB 0 1 0 0 0

9dB 0 1 0 0 1

10dB 0 1 0 1 0

11dB 0 1 0 1 1

12dB 0 1 1 0 0

13dB 0 1 1 0 1

14dB 0 1 1 1 0

15dB 0 1 1 1 1

16dB 1 0 0 0 0

17dB 1 0 0 0 1

18dB 1 0 0 1 0

19dB 1 0 0 1 1

20dB 1 0 1 0 0

Prohibition

1 0 1 0 1

：：：：：

1 1 1 1 0

1 1 1 1 1

Mode MSB Bass/Middle/Treble Boost/Cut LSB

D7 D6 D5 D4 D3 D2 D1 D0

Boost 0 0 0 Bass/Middle/Treble Gain

Cut 1

: Initial condition

Technical Note

25/37




Mode MSB Loudness Hicut LSB

D7 D6 D5 D4 D3 D2 D1 D0

Hicut1

0

0 0

Loudness Gain Hicut2 0 1

Hicut3 1 0

Hicut4 1 1

Gain MSB Loudness Gain LSB

D7 D6 D5 D4 D3 D2 D1 D0

0dB

0 Loudness Hicut

0 0 0 0 0

1dB 0 0 0 0 1

2dB 0 0 0 1 0

3dB 0 0 0 1 1

4dB 0 0 1 0 0

5dB 0 0 1 0 1

6dB 0 0 1 1 0

7dB 0 0 1 1 1

8dB 0 1 0 0 0

9dB 0 1 0 0 1

10dB 0 1 0 1 0

11dB 0 1 0 1 1

12dB 0 1 1 0 0

13dB 0 1 1 0 1

14dB 0 1 1 1 0

15dB 0 1 1 1 1

16dB 1 0 0 0 0

17dB 1 0 0 0 1

18dB 1 0 0 1 0

19dB 1 0 0 1 1

20dB 1 0 1 0 0

Prohibition

1 0 1 0 1

：：：：：

1 1 1 1 1

: Initial condition

（６）About power on reset

At on of supply voltage circuit made initialization inside IC is built-in. Please send data to all address

as initial data at supply voltage on. And please supply mute at set side until this initial data is sent.

Item Symbol Limit


Rise time of VCC Trise 33 －－ usec VCC rise time from 0V to 5V

VCC voltage of release

power on reset Vpor － 4.1 － V

（７））About external compulsory mute terminal

Mute is possible forcibly than the outside after input again department, by the setting of the MUTE terminal.

Mute Voltage Condition Mode

GND～1.0V MUTE ON

2.3V～VCC MUTE OFF

Establish the voltage of MUTE in the condition to have been defined.

Technical Note

26/37



Volume / Fader volume / Mixing attenuation of the details

(dB) D7 D6 D5 D4 D3 D2 D1 D0

(dB) D7 D6 D5 D4 D3 D2 D1 D0

+15 0 1 1 1 0 0 0 1 -33 1 0 1 0 0 0 0 1

+14 0 1 1 1 0 0 1 0 -34 1 0 1 0 0 0 1 0

+13 0 1 1 1 0 0 1 1 -35 1 0 1 0 0 0 1 1

+12 0 1 1 1 0 1 0 0 -36 1 0 1 0 0 1 0 0

+11 0 1 1 1 0 1 0 1 -37 1 0 1 0 0 1 0 1

+10 0 1 1 1 0 1 1 0 -38 1 0 1 0 0 1 1 0

+9 0 1 1 1 0 1 1 1 -39 1 0 1 0 0 1 1 1

+8 0 1 1 1 1 0 0 0 -40 1 0 1 0 1 0 0 0

+7 0 1 1 1 1 0 0 1 -41 1 0 1 0 1 0 0 1

+6 0 1 1 1 1 0 1 0 -42 1 0 1 0 1 0 1 0

+5 0 1 1 1 1 0 1 1 -43 1 0 1 0 1 0 1 1

+4 0 1 1 1 1 1 0 0 -44 1 0 1 0 1 1 0 0

+3 0 1 1 1 1 1 0 1 -45 1 0 1 0 1 1 0 1

+2 0 1 1 1 1 1 1 0 -46 1 0 1 0 1 1 1 0

+1 0 1 1 1 1 1 1 1 -47 1 0 1 0 1 1 1 1

0 1 0 0 0 0 0 0 0 -48 1 0 1 1 0 0 0 0

-1 1 0 0 0 0 0 0 1 -49 1 0 1 1 0 0 0 1

-2 1 0 0 0 0 0 1 0 -50 1 0 1 1 0 0 1 0

-3 1 0 0 0 0 0 1 1 -51 1 0 1 1 0 0 1 1

-4 1 0 0 0 0 1 0 0 -52 1 0 1 1 0 1 0 0

-5 1 0 0 0 0 1 0 1 -53 1 0 1 1 0 1 0 1

-6 1 0 0 0 0 1 1 0 -54 1 0 1 1 0 1 1 0

-7 1 0 0 0 0 1 1 1 -55 1 0 1 1 0 1 1 1

-8 1 0 0 0 1 0 0 0 -56 1 0 1 1 1 0 0 0

-9 1 0 0 0 1 0 0 1 -57 1 0 1 1 1 0 0 1

-10 1 0 0 0 1 0 1 0 -58 1 0 1 1 1 0 1 0

-11 1 0 0 0 1 0 1 1 -59 1 0 1 1 1 0 1 1

-12 1 0 0 0 1 1 0 0 -60 1 0 1 1 1 1 0 0

-13 1 0 0 0 1 1 0 1 -61 1 0 1 1 1 1 0 1

-14 1 0 0 0 1 1 1 0 -62 1 0 1 1 1 1 1 0

-15 1 0 0 0 1 1 1 1 -63 1 0 1 1 1 1 1 1

-16 1 0 0 1 0 0 0 0 -64 1 1 0 0 0 0 0 0

-17 1 0 0 1 0 0 0 1 -65 1 1 0 0 0 0 0 1

-18 1 0 0 1 0 0 1 0 -66 1 1 0 0 0 0 1 0

-19 1 0 0 1 0 0 1 1 -67 1 1 0 0 0 0 1 1

-20 1 0 0 1 0 1 0 0 -68 1 1 0 0 0 1 0 0

-21 1 0 0 1 0 1 0 1 -69 1 1 0 0 0 1 0 1

-22 1 0 0 1 0 1 1 0 -70 1 1 0 0 0 1 1 0

-23 1 0 0 1 0 1 1 1 -71 1 1 0 0 0 1 1 1

-24 1 0 0 1 1 0 0 0 -72 1 1 0 0 1 0 0 0

-25 1 0 0 1 1 0 0 1 -73 1 1 0 0 1 0 0 1

-26 1 0 0 1 1 0 1 0 -74 1 1 0 0 1 0 1 0

-27 1 0 0 1 1 0 1 1 -75 1 1 0 0 1 0 1 1

-28 1 0 0 1 1 1 0 0 -76 1 1 0 0 1 1 0 0

-29 1 0 0 1 1 1 0 1 -77 1 1 0 0 1 1 0 1

-30 1 0 0 1 1 1 1 0 -78 1 1 0 0 1 1 1 0

-31 1 0 0 1 1 1 1 1 -79 1 1 0 0 1 1 1 1

-32 1 0 1 0 0 0 0 0 -∞ 1 1 1 1 1 1 1 1

About BD37531FV, Fader Volume only 0dB～-∞dB are available.

Mixing is available only BD37533FV, BD37534FV. Adjustable range is +7dB～-∞dB.

：Initial condition

Technical Note

27/37



About Level meter(available only BD37534FV)

（１） The operation of circuit

Level meter is a function which gives DC voltage proportional to the size of signal of sound. It detects

the peak level of signal and keeps the peak level, so that it is possible to monitor the size of signal by

resetting DC voltage kept with suitable interval.

（２） The way to reset level meter output

Please send reset data through I2C BUS

When reset output of level meter：Send D6 = “ 1 “ of select address 02(hex).

When cancel of output reset of level meter (HOLD)… → Send D6 = “ 0 “ of select address 02(hex).

（３） The settings about period of reset

Peak hold operation will start after HOLD data is transmitted. Set the WAIT time after HOLD data transmission

according to the frequency bandwidth detected.

WAIT time must be set to a minimum of one cycle over the detected frequency bandwidth.

Ex) Detected frequency bandwidth is above 40Hz, 『40Hz = 25ms = WAIT time』

Transmission Example by I2C BUS

I2CBUS

t

(25msec) Wait time

detect

※fin＝40Hz

RESET START HOLD

START

(RESET) (HOLD)

80 10

02 40 80 02 00

LOUT [ V ]

Technical Note

28/37



Application circuit

Fig.28 BD37531FV

Notes on wiring ① Please connect the decoupling capacitor of a power supply in the shortest distance as much as possible to GND.② Lines of GND shall be one-point connected. ③ Wiring pattern of Digital shall be away from that of analog unit and cross-talk shall not be acceptable. ④ Lines of SCL and SDA of I2C BUS shall not be parallel if possible.

The lines shall be shielded, if they are adjacent to each other. ⑤ Lines of analog input shall not be parallel if possible. The lines shall be shielded, if they are adjacent

to each other. ⑥ About TEST pin(14,16,17pin), please use with OPEN.

FIL GND SDA SCL MUTE10μ 0.1μ

10μ

OUTF1 OUTF2 OUTR1 OUTR2 OUTS1 OUTS2

Single1 Single2 Single3 GND Isolation1 or Single4

Full Differential orSingle5, Single6

GND Isolation2 GND Isolation3

※Single1～3はGND Isolation2,3に切換可能（About single input 1～3, it is possible to change from single input to GND Isolation input 2,3.）

※GND Isolation1, Full DifferentialはSingle4～6に切換可能

（About GND Isolation1 and Full Differential, it is possible to change from differential input to single input 4～6.）

VCC

10μ 10μ 10μ 10μ 10μ

2.2μ 2.2μ 2.2μ 2.2μ 2.2μ 2.2μ 2.2μ 10μ 2.2μ 2.2μ 10μ 10μ 2.2μ

GNDVCC/2

28 27 26 25 24 23 22 21 20 19 18 17 16 15

Volume/Mute


Loudness

Fad

er

Fad

er

Fad

er

Fad

er

Fad

er

Input Gain

GNDISO amp


1 2 3 4 5 6 7 8 9 10 11 12 13 14

100k 100k 100k 100k 100k 100k 250k

GNDISO amp

250k250k

GNDISO amp

250k 250k

GNDISO amp

250k 250k

VCC

I2C BUS LOGIC

Fader Gain:0dB～-79ｄB/1dB step

no pop noiseLoudness Gain:20dB～0ｄB/1ｄB step




Q=0.5/1.0/1.5/2.0・Meddle:f0=500/1k/1.5k/2.5kHz

Q=0.75/1/1.25/1.5・Treble：f0=7.5k/10k/12.5k/15kHz



no pop noise

10μ TEST3 TEST2

TEST1

Unit

R : [Ω] C : [F]

※About single input 1～3, it is possible to change

from single input to GND Isolation input 2,3.

※About GND Isolation1 and Full Differential, it is possible

to change from differential input to single input 4～6.

Technical Note

29/37



Fig.29 BD37532FV



to each other. ⑥ About TEST pin(14,15,16pin), please use with OPEN.


10μ

OUTF1 OUTF2 OUTR1 OUTR2 OUTS1 OUTS2VCC

10μ 10μ 10μ 10μ 10μ

2.2μ 2.2μ 2.2μ 2.2μ 2.2μ 2.2μ 2.2μ 10μ 2.2μ 2.2μ 10μ 10μ 2.2μ

GNDVCC/2

28 27 26 25 24 23 22 21 20 19 18 17 16 15

Volume/Mute


Loudness

Fade

r

Fade

r

Fade

r

Fade

r

Fade

r

LPF

Input Gain

GNDISO amp


1 2 3 4 5 6 7 8 9 10 11 12 13 14

100k 100k 100k 100k 100k 100k 250k

GNDISO amp

250k250k

GNDISO amp

250k 250k

GNDISO amp

250k 250k

VCC

I2C BUS LOGIC






Q=0.5/1.0/1.5/2.0・Meddle:f0=500/1k/1.5k/2.5kHz

Q=0.75/1/1.25/1.5・Treble：f0=7.5k/10k/12.5k/15kHz



no pop noise




※Single1～3はGND Isolation2,3に切換可能

（About single input 1～3, it is possible to change from single input to GND Isolation input 2,3.）



10μ TEST3 TEST2

TEST1

Unit

R : [Ω] C : [F]





Technical Note

30/37



Fig.30 BD37533FV



to each other. ⑥ About TEST pin(16,17pin), please use with OPEN.


10μ


MIN

VCC

10μ 10μ 10μ 10μ 10μ

2.2μ 2.2μ 2.2μ 2.2μ 2.2μ 2.2μ 2.2μ 10μ 2.2μ 2.2μ 10μ 10μ 2.2μ 2.2μ

GNDVCC/2

28 27 26 25 24 23 22 21 20 19 18 17 16 15

Volume/Mute


Loudness

Fad

er

Fad

er

Fad

er

Fad

er

Fad

er

LPF

Input Gain

ATT

GNDISO amp


1 2 3 4 5 6 7 8 9 10 11 12 13 14

100k 100k 100k 100k 100k 100k 250k

GNDISO amp

250k250k

GNDISO amp

250k 250k

GNDISO amp

250k 250k

VCC

I2C BUS LOGIC






Q=0.5/1.0/1.5/2.0・Meddle:f0=500/1k/1.5k/2.5kHz

Q=0.75/1/1.25/1.5・Treble：f0=7.5k/10k/12.5k/15kHz



no pop noise




※Single1～3はGND Isolation2,3に切換可能（About single input 1～3, it is possible to change from single input to GND Isolation input 2,3.）



10μ TEST2 TEST1

Unit

R : [Ω] C : [F] ※About single input 1～3, it is possible to change




Technical Note

31/37




10μ


Single1 Single2 Single3 MIN

GND Isolation3

VCC

10μ 10μ 10μ 10μ 10μ

2.2μ 2.2μ 2.2μ 2.2μ 2.2μ 2.2μ 2.2μ 10μ 2.2μ 2.2μ 10μ 10μ 2.2μ 2.2μ

LOUT LRST

GNDVCC/2

28 27 26 25 24 23 22 21 20 19 18 17 16 15

Volume/Mute


Loudness

Fad

er

Fad

er

Fad

er

Fad

er

Fad

er

LPF

Input Gain

ATT

GNDISO amp


1 2 3 4 5 6 7 8 9 10 11 12 13 14

100k 100k 100k 100k 100k 100k 250k

GNDISO amp

250k250k

GNDISO amp

250k 250k

GNDISO amp

250k 250k

Level meter

VCC

I2C BUS LOGIC






Q=0.5/1.0/1.5/2.0・Meddle:f0=500/1k/1.5k/2.5kHz

Q=0.75/1/1.25/1.5・Treble：f0=7.5k/10k/12.5k/15kHz



no pop noise

10μ

Fig.31 BD37534FV



to each other.

Unit

R : [Ω] C : [F]





Technical Note

32/37



Interfaces

Terminal

No.

Terminal

Name

Terminal

Voltage Equivalent Circuit Terminal Description

1

2

3

4

5

6

A1

A2

B1

B2

C1

C2

4.25

A terminal for signal input.

The input impedance is 100kΩ(typ).

7

8

9

10

11

12

13

DP1

DN

DP2

EP1

EN1

EN2

EP2

4.25

Input terminal available to

single/Differential mode.


15 MUTE －

A terminal for external compulsory mute.

If terminal voltage is High level, the

mute is off. And if the terminal voltage

is Low level, the mute is on.

18

19

20

21

22

23

OUTS2

OUTS1

OUTR2

OUTR1

OUTF2

OUTF1

4.25

A terminal for fader and Subwoofer output.

17

LOUT

0～3.3

A terminal for level meter output

(BD37534FV)

Output impedance is 10kΩ(typ).

The figure in the pin explanation and input/output equivalent circuit is reference value, it doesn’t guarantee the value.

GND

Vcc

100k

GND

Vcc

250ｋ

VCC

GND

Vcc

GND

1.65V

10k

GND

VCC

Technical Note

33/37



Terminal

No.

Terminal

Name

Terminal

Voltage Equivalent Circuit Terminal Description

24 VCC 8.5

Power supply terminal.

25 SCL －

A terminal for clock input of I2C BUS

communication.

26 SDA －

A terminal for data input of I2C BUS

communication.

27 GND 0

Ground terminal.

28 FIL 4.25

Voltage for reference bias of analog

signal system. The simple precharge

circuit and simple discharge circuit for

an external capacitor are built in.

14 MIN 4.25

A terminal for signal input

(BD37533FV, BD37534FV)


14

16

17

TEST -

TEST terminal

(BD37531FV,BD37532FV,BD37533FV)

About BD37531FV and BD37532FV,

14,16,17pin are TEST Pin.

About BD37533FV, 16,17pin are TEST Pin.

The figure in the pin explanation and input/output equivalent circuit is reference value, it doesn’t guarantee the value.

Vcc

GND

1.65V

Vcc

GND

50k

50k

Vcc

GND

1.65V

GND

Vcc

27k

Technical Note

34/37



Notes for use

1. Absolute maximum rating voltage

When it impressed the voltage on VCC more than the absolute maximum rating voltage, circuit currents increase

rapidly, and there is absolutely a case to reach characteristic deterioration and destruction of a device.

In particular in a serge examination of a set, when it is expected the impressing serge at VCC terminal (24pin),

please do not impress the large and over the absolute maximum rating voltage (including a operating voltage

+ serge ingredient (around 14V)).

2. About a signal input part

1）About constant set up of input coupling capacitor

In the signal input terminal, the constant setting of input coupling capacitor C(F) be sufficient input

impedance RIN(Ω) inside IC and please decide. The first HPF characteristic of RC is composed.

2) About the input selector SHORT

SHORT mode is the command which makes switch SSH =ON an input selector part and input impedance RIN of all

terminals, and makes resistance small. Switch SSH is OFF when not choosing a SHORT command.

A constant time becomes small at the time of this command twisting to the resistance inside the capacitor

connected outside and LSI. The charge time of a capacitor becomes short. Since SHORT mode turns ON the switch

of SSH and makes it low impedance, please use it at the time of a non-signal.

3. About Mute terminal(15pin) when power supply is off

Any voltage shall not be supplied to Mute terminal (15pin) when power-supply is off.

Please insert a resistor (about 2.2kΩ) to Mute terminal in series, if voltage is supplied to mute terminal

in case. (Please refer Application Circuit Diagram.)

4. About TEST Pin

About TEST Pin, please use with OPEN.

About BD37531FV and BD37532FV, 14,16,17pin are TEST Pin. About BD37533FV, 16,17pin are TEST Pin.

2IN)

2IN

(2πfCR1

)(2πfCRA(f)

0

A(f)

G〔dB〕

f〔Hz〕

C〔F〕

RIN 〔Ω〕

INPUT

ＳＳ

Technical Note

35/37



5. About Mixing (BD3753FV,BD37534FV)

・About specification of Fader -∞ at Mixing ON.

Mixed signal is added to Main signal after Fader Gain(+15～-79dB) like the following figure. When Fader is made

a set up in -∞, the signal after a Mixing signal is added is done with MUTE. Because the -∞ circuit of Fader

is in the step after the addition circuit.

・About advanced switching of Mixing Gain/ATT

When advanced switching of Mixing Gain/ATT works, Mixing becomes the switching movement that it passed through

state of Mixing OFF like B (A present setup of Mixing Gain/ATT → Mixing OFF → A target setup of Mixing

Gain/ATT).

Fig.32 About Front Fader and Mixing

Fig.33 Advanced switching movement when Mixing Gain/ATT is changed

A B

Fader Gain/ATT 0dB → -6dB advanced switching Mixing Gain/ATT 0dB → -6dB advanced switching

Technical Note

36/37



Thermal Derating Curve

About the thermal design by the IC

Characteristics of an IC have a great deal to do with the temperature at which it is used, and exceeding absolute

maximum ratings may degrade and destroy elements. Careful consideration must be given to the heat of the IC from the

two standpoints of immediate damage and long-term reliability of operation.

Fig.34 Temperature Derating Curve

Power dissipation values vary according to the board on which the IC is mounted.

SSOP-B28 1.5

1.0

0.5

0.0

0 25 50 75 100 125 150

1.063W

θja = 117.6/W

85

Reference data

Ambient Temperature Ta（）

Power Dissipation Pd（W） Measurement condition: ROHM Standard board

board Size：70×70×1.6()

material：A FR4 grass epoxy board

(3% or less of copper foil area)

Note) Values are actual measurements and are not guaranteed.

Technical Note

37/37



Ordering part number

B D 3 7 5 3 1 F V - E 2

Part No. Part No.

37531

37532

37533

37534

Package

FV : SSOP-B28

Packaging and forming specification

E2: Embossed tape and reel

(Unit : mm)

SSOP-B28

0.1

0.15 ± 0.1

0.11.

15 ±

0.1

1

0.65

7.6

± 0.

3

5.6

± 0.

2

28

10 ± 0.2(MAX 10.35 include BURR)

0.3M

in.

14

15

0.22 ± 0.1

∗ Order quantity needs to be multiple of the minimum quantity.

<Tape and Reel information>

Embossed carrier tapeTape

Quantity

Direction of feed

The direction is the 1pin of product is at the upper left when you hold reel on the left hand and you pull out the tape on the right hand

2000pcs

E2

( )

Direction of feed

Reel1pin

R1010Awww.rohm.com© 2010 ROHM Co., Ltd. All rights reserved.

Notice

ROHM Customer Support Systemhttp://www.rohm.com/contact/

Thank you for your accessing to ROHM product informations. More detail product informations and catalogs are available, please contact us.

No t e s

No copying or reproduction of this document, in part or in whole, is permitted without the consent of ROHM Co.,Ltd.

The content specified herein is subject to change for improvement without notice.

The content specified herein is for the purpose of introducing ROHM's products (hereinafter "Products"). If you wish to use any such Product, please be sure to refer to the specifications, which can be obtained from ROHM upon request.

Examples of application circuits, circuit constants and any other information contained herein illustrate the standard usage and operations of the Products. The peripheral conditions must be taken into account when designing circuits for mass production.

Great care was taken in ensuring the accuracy of the information specified in this document. However, should you incur any damage arising from any inaccuracy or misprint of such information, ROHM shall bear no responsibility for such damage.

The technical information specified herein is intended only to show the typical functions of and examples of application circuits for the Products. ROHM does not grant you, explicitly or implicitly, any license to use or exercise intellectual property or other rights held by ROHM and other parties. ROHM shall bear no responsibility whatsoever for any dispute arising from the use of such technical information.

The Products specified in this document are intended to be used with general-use electronic equipment or devices (such as audio visual equipment, office-automation equipment, commu-nication devices, electronic appliances and amusement devices).

The Products specified in this document are not designed to be radiation tolerant.

While ROHM always makes efforts to enhance the quality and reliability of its Products, a Product may fail or malfunction for a variety of reasons.

Please be sure to implement in your equipment using the Products safety measures to guard against the possibility of physical injury, fire or any other damage caused in the event of the failure of any Product, such as derating, redundancy, fire control and fail-safe designs. ROHM shall bear no responsibility whatsoever for your use of any Product outside of the prescribed scope or not in accordance with the instruction manual.

The Products are not designed or manufactured to be used with any equipment, device or system which requires an extremely high level of reliability the failure or malfunction of which may result in a direct threat to human life or create a risk of human injury (such as a medical instrument, transportation equipment, aerospace machinery, nuclear-reactor controller, fuel-controller or other safety device). ROHM shall bear no responsibility in any way for use of any of the Products for the above special purposes. If a Product is intended to be used for any such special purpose, please contact a ROHM sales representative before purchasing.

If you intend to export or ship overseas any Product or technology specified herein that may be controlled under the Foreign Exchange and the Foreign Trade Law, you will be required to obtain a license or permit under the Law.