SERVICE MANUAL

PERSONAL AUDIO SYSTEM

US ModelCanadian Model

E ModelAustralian Model

ZS-SN10Ver. 1.4 2006.03

9-879-649-052006C05-1© 2006.03

Sony CorporationPersonal Audio DivisionPublished by Sony Techno Create Corporation

Model Name Using Similar Mechanism CFD-E95

Optical Pick-up Block Name KSM-213CDP

Optical Pick-up Name KSS-213C

SPECIFICATIONS

US and foreign patents licensed from Dolby Laboratories.

Radio sectionFrequency rangeUS, CND, E, MX, TW models:

FM: 87.5 - 108 MHzAM: 530 - 1710 kHz

AUDIO POWER SPECIFICATIONS(US model only)POWER OUTPUT AND TOTAL HARMONICDISTORTIONWith 3.2-ohm loads, both channels driven from150 - 6,300 Hz; rated 1.8 W per channel-minimumRMS power, with no more than 10 % totalharmonic distortion in AC operation.

Other SpecificationsCD player sectionSystem

Compact disc digital audio systemLaser diode properties

Emission duration: ContinuousLaser output: Less than 44.6 µW(This output is the value measured at a distance of about200 mm from the objective lens surface on the opticalpick-up block with 7 mm aperture.)

Spindle speed200 r/min (rpm) to 500 r/min (rpm) (CLV)

Number of channels2

Frequency response20 - 20 000 Hz +0/–1 dB

Wow and flutterBelow measurable limit

SP, KR, TH, AUS models:FM: 87.5 - 108 MHzAM: 531 - 1611 kHz (9 kHz step) 530 - 1610 kHz (10 kHz step)

IFFM: 10.7 MHzAM: 450 kHz

AntennasFM: Telescopic antennaAM: Built-in ferrite bar antenna

GeneralSpeaker

Full range: 10 cm (4 in.) dia., 3.2 Ω, cone type (2)Input

LINE IN jack (stereo minijack):Minimum input level 330 mV

OutputsHeadphones jack (stereo minijack):For 16 - 64 Ω impedance headphones

Power output2.3 W + 2.3 W (at 3.2 Ω, 10 % harmonicdistortion)

Power requirementsFor player:US, CND, E, MX, TW models:120 V AC, 60 HzSP, TH, AUS models:230 V AC, 50 HzKR model:220 V AC, 60 Hz

9 V DC, 6 size D (R20) batteriesFor remote control:3 V DC, 2 size AAA (R03) batteries

Power consumption16 W

Battery lifeFor player:

CD playback

Sony R20P: approx. 2 h

Sony alkaline LR20: approx. 8 h

Radio reception

Sony R20P: approx. 10 h

Sony alkaline LR20: approx. 25 h

DimensionsApprox. 500 × 145 × 230 mm (w/h/d)(19 3/4 × 5 3/4 × 9 1/8 inches) (incl. projecting parts)

MassApprox. 3.8 kg (8 lb. 6 oz) (incl. batteries)

Supplied accessoriesAC power cord (1) (US, CND, E, MX, TW models)Mains lead (1) (SP, KR, TH, AUS models)Remote control (1)CD-ROM (SonicStage) (1)SonicStage Installation/Operating Guide (1)

Design and specifications are subject to change withoutnotice.

• AbbreviationAUS : Australian modelCND: Canadian modelKR : Korean modelMX : Mexican modelSP : Singapore modelTH : Thai modelTW : Taiwan model

ZS-SN10

2

Notes on chip component replacement• Never reuse a disconnected chip component.• Notice that the minus side of a tantalum capacitor may be

damaged by heat.

Flexible Circuit Board Repairing• Keep the temperature of the soldering iron around 270 ˚C

during repairing.• Do not touch the soldering iron on the same conductor of the

circuit board (within 3 times).• Be careful not to apply force on the conductor when soldering

or unsoldering.

SAFETY-RELATED COMPONENT WARNING!!

COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINEWITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND INTHE PARTS LIST ARE CRITICAL TO SAFE OPERATION.REPLACE THESE COMPONENTS WITH SONY PARTS WHOSEPART NUMBERS APPEAR AS SHOWN IN THIS MANUAL ORIN SUPPLEMENTS PUBLISHED BY SONY.

CAUTIONUse of controls or adjustments or performance of proceduresother than those specified herein may result in hazardous radiationexposure.

SAFETY CHECK-OUTAfter correcting the original service problem, perform the followingsafety check before releasing the set to the customer:Check the antenna terminals, metal trim, “metallized” knobs, screws,and all other exposed metal parts for AC leakage.Check leakage as described below.

LEAKAGE TESTThe AC leakage from any exposed metal part to earth ground andfrom all exposed metal parts to any exposed metal part having areturn to chassis, must not exceed 0.5 mA (500 microamperes.).Leakage current can be measured by any one of three methods.

1. A commercial leakage tester, such as the Simpson 229 or RCAWT-540A. Follow the manufacturers’ instructions to use theseinstruments.

2. A battery-operated AC milliammeter. The Data Precision 245digital multimeter is suitable for this job.

3. Measuring the voltage drop across a resistor by means of aVOM or battery-operated AC voltmeter. The “limit” indicationis 0.75 V, so analog meters must have an accurate low-voltagescale. The Simpson 250 and Sanwa SH-63Trd are examplesof a passive VOM that is suitable. Nearly all battery operateddigital multimeters that have a 2 V AC range are suitable. (SeeFig. A)

Fig. A. Using an AC voltmeter to check AC leakage.

1.5 kΩ0.15 µFACvoltmeter(0.75 V)

To Exposed MetalParts on Set

Earth Ground

ATTENTION AU COMPOSANT AYANT RAPPORTÀ LA SÉCURITÉ!

LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE 0 SURLES DIAGRAMMES SCHÉMATIQUES ET LA LISTE DESPIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DEFONCTIONNEMENT. NE REMPLACER CES COM- POSANTSQUE PAR DES PIÈCES SONY DONT LES NUMÉROS SONTDONNÉS DANS CE MANUEL OU DANS LES SUPPLÉMENTSPUBLIÉS PAR SONY.

TABLE OF CONTENTS

1. SERVICING NOTES ................................................ 3

2. GENERAL ................................................................... 4

3. DISASSEMBLY3-1. Disassembly Flow ........................................................... 63-2. Cabinet Top Assy ............................................................. 63-3. MAIN Board .................................................................... 73-4. Cabinet Front Assy .......................................................... 73-5. LCD Board ...................................................................... 83-6. CD Block Assy ................................................................ 83-7. Optical Pick-up (KSS-213C) ........................................... 93-8. CD Lid ............................................................................. 9

4. ELECTRICAL ADJUSTMENTS .......................... 10

5. DIAGRAMS5-1. Block Diagram – CD Servo Section – ............................ 125-2. Block Diagram – TUNER Section – .............................. 135-3. Block Diagram – MAIN Section – ................................ 145-4. Printed Wiring Board – CD Board – .............................. 165-5. Schematic Diagram – CD Board – ................................. 175-6. Printed Wiring Board – TUNER Board – ....................... 185-7. Schematic Diagram – TUNER Board – ......................... 195-8. Printed Wiring Boards – MAIN Section – ..................... 205-9. Printed Wiring Boards – POWER Section – .................. 215-10. Schematic Diagram – MAIN Section (1/2) – ................. 225-11. Schematic Diagram – MAIN Section (2/2) – ................. 235-12. Printed Wiring Boards – PANEL Section – .................... 245-13. Schematic Diagram – PANEL Section – ........................ 25

6. EXPLODED VIEWS6-1. Cabinet Section ................................................................ 336-2. Cabinet Front Section ...................................................... 346-3. Cabinet Top Section-1 ..................................................... 356-4. Cabinet Top Section-2 ..................................................... 366-5. Cabinet Bottom Section ................................................... 376-6. Optical Pick-up Section (KSM-213CDP) ....................... 38

7. ELECTRICAL PARTS LIST .................................. 39

3

ZS-SN10SECTION 1

SERVICING NOTES

The laser diode in the optical pick-up block may suffer electrostaticbreak-down because of the potential difference generated by thecharged electrostatic load, etc. on clothing and the human body.During repair, pay attention to electrostatic break-down and alsouse the procedure in the printed matter which is included in therepair parts.The flexible board is easily damaged and should be handled withcare.

NOTES ON LASER DIODE EMISSION CHECKThe laser beam on this model is concentrated so as to be focused onthe disc reflective surface by the objective lens in the optical pick-up block. Therefore, when checking the laser diode emission,observe from more than 30 cm away from the objective lens.

UNLEADED SOLDERBoards requiring use of unleaded solder are printed with the lead-free mark (LF) indicating the solder contains no lead.(Caution: Some printed circuit boards may not come printed with

the lead free mark due to their particular size)

: LEAD FREE MARKUnleaded solder has the following characteristics.

• Unleaded solder melts at a temperature about 40 °C higherthan ordinary solder.Ordinary soldering irons can be used but the iron tip has to beapplied to the solder joint for a slightly longer time.Soldering irons using a temperature regulator should be set toabout 350 °C.Caution: The printed pattern (copper foil) may peel away if

the heated tip is applied for too long, so be careful!• Strong viscosity

Unleaded solder is more viscou-s (sticky, less prone to flow)than ordinary solder so use caution not to let solder bridgesoccur such as on IC pins, etc.

• Usable with ordinary solderIt is best to use only unleaded solder but unleaded solder mayalso be added to ordinary solder.

NOTES ON HANDLING THE OPTICAL PICK-UPBLOCK OR BASE UNIT

LASER DIODE AND FOCUS SEARCH OPERATIONCHECKDuring normal operation of the equipment, emission of the laserdiode is prohibited unless the upper lid is closed while turning ONthe S801. (push switch type)The following checking method for the laser diode is operable.• Method

Emission of the laser diode is visually checked.1. Open the upper lid.2. Push the S801 as shown in Fig.1.

Note: Do not push the detection lever strongly, or it may be bent or damaged.3. Press the u button.4. Check the object lens for confirming normal emission of the

laser diode. If not emitting, there is a trouble in the automaticpower control circuit or the optical pick-up.In this operation, the object lens will move up and down 2times along with inward motion for the focus search.

Fig.1 Method to push the S801

S801

4

ZS-SN10SECTION 2GENERAL

This section is extracted frominstruction manual.

Playing a CD

Connect the supplied AC power cord.

1 Press PUSH Z OPEN/CLOSE toopen the CD lid and place the CD onthe CD tray.

2 Press PUSH Z OPEN/CLOSE toclose the CD lid.

With the label side up

3

Basic Operations

1, 2

Playing timeTrack number

Playing timeFile number

3 Pressu (N on the remote) (directpower-on).

The player plays all the tracks once.

* When playing an MP3 CD, “MP3”appears in the display.

DisplayAudio CD

u

VOLUME –, +

x

Use these buttons for additional operations

To Press

adjust the volume VOLUME +*1, – (VOL +*1, – on theremote)

stop playback x

pause playback u*1 (X on the remote)Press the button again to resume play afterpause.

go to the next track >

go back to the .

previous track

*1 The button has a tactile dot.

Tips• To listen through

headphones, connect theheadphones to the i(headphones) jack.

• Playback starts from thetrack you last stoppedplaying (Resume play).To cancel the resume playto start play from thebeginning of the first track,pressx in stop mode.

File name

ATRAC CD/MP3 CD*

>

.

–, +

NoteBefore playing an ATRACCD/MP3 CD, this playerreads all file and groupinformation on the CD.Depending on the filestructure, it may take morethan a minute to read them.During this time, “Reading”is displayed.

POWER

i

Notes• If ATRAC3plus files and

MP3 files are recorded onthe same CD, this CDplayer plays theATRAC3plus first.

• The playback capability ofthis CD player may varydepending on the quality ofthe disc and the condition ofthe recording device.

• Characters that can bedisplayed on this CD playerare listed below.– A to Z– a to z– 0 to 9– ! " # $ % & ' ( ) * + , - . / :

; < = > ? @ [ \ ] ^ _ ` | ~

If you use other characterson your computer usingsoftware such asSonicStage, they aredisplayed as “–” on this CDplayer.

• On a disc that hasATRAC3plus/MP3 files, donot save files in otherformats and do not makeunneccessary groups.

ATRAC CD

To Press

select a group*2 + to go forward and – to gobackward

remove the CD PUSH Z OPEN/CLOSE*3

turn on/off the player POWER

*2 This function works for ATRAC CDs/MP3 CDs only.*3 Once you open the CD lid, the track to start play will change to

the beginning of the first track.

The structure of ATRAC CDs/MP3 CDsATRAC CDs/MP3 CDs consist of “files” and “groups.” A“file” is equivalent to a “track” of an audio CD. A “group”is a bundle of files and is equivalent to an “album.”For MP3 CDs, this CD player recognizes an MP3 folder asa “group” so that ATRAC CDs and MP3 CDs can beoperated in the same way.In this manual, we use the word “track” in description ofthe operations available for both ATRAC CDs/MP3 CDsand audio CDs, and the word “file” for the operationsavailable for ATRAC CDs/MP3 CDs only.

Playing order of ATRAC CDs and MP3 CDsFor ATRAC CDs, files are played in the order selected inSonicStage.For MP3 CDs, the playing order may differ depending onthe method used to record MP3 files on the disc. In thefollowing example, files are played in order of 1 to 7.

File

Group

MP3 CD

Notes on ATRAC CDs• Maximum number of groups: 255

Maximum number of files: 999• CD-Rs/CD-RWs recorded in the ATRAC3plus format cannot be

played on your computer.

Notes on MP3 CDs• Maximum number of groups: 255

Maximum number of files: 511Maximum directory level: 8

• A group that does not include an MP3 file is skipped.• Be sure to add the file extension “mp3” to the file name.

However, if you add the file extension “mp3” to a file other thanan MP3 file, the player will not be able to recognize the fileproperly.

• This player can play bit rates of 32 to 320 kbps, and samplingfrequencies of 32/44.1/ 48 kHz.

• To compress a source in an MP3 file, we recommend setting thecompression parameters to “44.1 kHz,” “128 kbps,” and“Constant Bit Rate.”

• To record up to the maximum capacity, set the writing softwareto “halting of writing.”

• To record to the maximum capacity at one time up on media thathas nothing recorded on it, set the writing software to “Disc atOnce.”

5

ZS-SN10

Listening to the radio

Connect the supplied AC power cord.

1 Press RADIO•BAND•AUTOPRESET repeatedly until the bandyou want appears in the display(direct power-on).

2 Hold down TUNE + or – until thefrequency digits begin to change inthe display.

The player automatically scans theradio frequencies and stops when itfinds a clear station.

If you can’t tune in a station, pressTUNE + or – repeatedly to changethe frequency step by step.

1 2

Display

Indicates an FMstereo broadcast

Use these buttons for additional operations

TipIf the FM broadcast is noisy,press MODE repeatedly until“Mono” appears in thedisplay and radio will play inmonaural.

To Press

adjust the volume VOLUME +*, – (VOL +*, – on theremote)

turn on/off the radio POWER

* The button has a tactile dot.

To improve broadcast receptionReorient the antenna for FM. Reorient the player itself forAM.

VOLUME –, +

MODE

for FM for AM

POWER

6

ZS-SN10

• This set can be disassembled in the order shown below.

3-1. DISASSEMBLY FLOW

SECTION 3DISASSEMBLY

3-2. CABINET TOP ASSY(Page 6)

3-6. CD BLOCK ASSY(Page 8)

3-8. CD LID(Page 9)

3-7. OPTICAL PICK-UP(KSS-213C)(Page 9)

3-3. MAIN BOARD(Page 7)

3-4. CABINET FRONT ASSY(Page 7)

3-5. LCD BOARD(Page 8)

SET

qa flexible flat cable (4 core)(CN403)

qs cabinet top assy

8 6 two screws (B3)

1 screw (M3)

2 telescopic antenna (ANT1)

4 three screws(B3)

3 Open the CD lid.

5 Lift the handle.7 three screws

(B3)

0 wire (flat type) (23 core)(CN102)

9 connector

Note: Follow the disassembly procedure in the numerical order given.

3-2. CABINET TOP ASSY

7

ZS-SN10

3-3. MAIN BOARD

3-4. CABINET FRONT ASSY

1 connector (CN302)

6 flexible flat cable(11 core) (CN801)

7 two screws(B2.6)

2 connector (CN301)3 connector (CN901)

5 flexible flat cable(11 core) (CN807)

4 flexible flat cable(11 core) (CN806)

8 MAIN board

4 five screws(B3)

5 screw (B3)

6 cabinet front assy

1 connector(CN323)

2 two screws(B3)

3 two screws(B3)

8

ZS-SN10

3-5. LCD BOARD

1 four screws(B3)

3 four screws(B3)

2 speaker box (L)

4 speaker box (R)

8 LCD board

6 two screws(B2.6)

5 four screws(B2.6)

7 two screws(B2.6)

3-6. CD BLOCK ASSY

1 four screws

2 CD block assy

9

ZS-SN10

3-7. OPTICAL PICK-UP (KSS-213C)

3-8. CD LID

4 flexible flat cable (16 core)

1 CD cover

2 gear (A)

3 sled shaft

5 optical pick-up(KSS-213C)

3 screw (B2.6)

4 damper

2 CD spring

1 claw

7 boss5

9 CD lid

6 claw

8 boss

10

ZS-SN10SECTION 4

ELECTRICAL ADJUSTMENTS

TUNER SECTION 0 dB=1 µV

[AM]Setting:Function: RADIORADIO/BAND, AUTO PRESET button: AM

[FM]Setting:Function: RADIORADIO/BAND, AUTO PRESET button: FM

• Repeat the procedures in each adjustment several times, andthe tracking adjustments should be finally done by the trimmercapacitors.

• Remove FM antenna in FM adjustment.

AM RF signal generator

30% amplitudemodulation by400 Hz signalOutput level: as low as possible

Put the lead-wireantenna close to the set.

+–

level meter

set

32 Ω

i jack (J301)

FM RF signalgenerator

75 kHz frequencydeviation by 1 kHzsignalOutput level: as low as possible

+–

level meter 0.01 µF

TUNER boardTP (GND)

TUNER boardTP (ANT)

set

32 Ω

i jack (J301)

digital voltmeter

TP (VT)TP (GND)

100 kΩTUNER board

AM IF ADJUSTMENT

Adjust for a maximum reading on level meter

T1 450 kHz

( ): Singapore, Korean, Thai and Australian models

AM FREQUENCY COVERAGE ADJUSTMENT

Adjustment Part Frequency Display Reading on Digital Voltmeter

L4 530 kHz (531 kHz) 1.0 ± 0.05 V

Confirmation1,710 kHz

5.3 ± 0.7 V (5.2 ± 0.6 V) (1,611 kHz)

( ): Singapore, Korean, Thai and Australian models

AM TRACKING ADJUSTMENT

Adjust for a maximum reading on level meter

L3 620 kHz (621 kHz)

CT3 1,400 kHz (1,404 kHz)

FM IF ADJUSTMENT

Adjust for a minimum reading on level meter

T2 10.7 MHz

FM FREQUENCY COVERAGE ADJUSTMENT

Adjustment Part Frequency Display Reading on Digital Voltmeter

L2 108 MHz 3.0 ± 0.2 V

Confirmation 87.5 MHz 1.3 ± 0.3 V

FM TRACKING ADJUSTMENT

Adjust for a maximum reading on level meter

L1 87.5 MHz

CT1 108 MHz

Adjustment and Connecting Location: TUNER board(See page 11)

Ver. 1.1

ZS-SN10

1111ZS-SN10

CD SECTION

FOCUS BIAS CHECK1. Connect the oscilloscope to TP (RFACO) and TP (VC) on the

CD board.2. Insert the disc (PATD-012). (Part No.: 4-225-203-01)3. Press the u button.4. Confirm that the oscilloscope waveform is as shown in the

figure below. (eye pattern)A good eye pattern means that the diamond shape (◊) in thecenter of the waveform can be clearly distinguished.

• RF signal reference waveform (eye pattern)

VOLT/DIV: 0.2 V (with the 10: 1 probe in use.)TIME/DIV: 200 ns

0.5 to 1.1 Vp-p

When observing the eye pattern, set the oscilloscope for AC range and raise vertical sensitivity.

TP(VC)

TP(RFACO)

IC201

– CD Board (Conductor Side) –

Checking Location:

Adjustment and Connecting Location:

L4AM Frequency Coverage Adjustment

L2FM Frequency Coverage Adjustment

AM Tracking Adjustment CT3L3

FM Tracking Adjustment

T1 AM IF Adjustment

T2 FM IF Adjustment

L1CT1

TP(VT)

TP(GND)

TP(ANT)

– TUNER Board (Component Side) –

– TUNER Board (Conductor Side) –

1212

ZS-SN10

ZS-SN10

5-1. BLOCK DIAGRAM – CD SERVO SECTION –

OPTICALPICK-UP BLOCK(KSM-213CDP)

CH2OUTF CH2FIN

FOCUS/TRACKING COIL DRIVER,SLED/SPINDLE MOTOR DRIVER

IC402

12 6

CH2OUTR11CH1OUTR13CH1OUTF14

CH3OUTF17

CH3OUTR18SL–

SL+

TRK–TRK+FCS–

FCS+2-AXISDEVICE

PD

LD

B

A

D

C

F

E

M402(SLED) M

CH4OUTF16

CH4OUTR15

CH2RIN 7CH1RIN 5CH1FIN 4

CH3FIN 23

CH3RIN 22

OPIN+ 2

CH4IN 24

OPOUT 27

FFDR45

PD67

F51

E50

D60

C59

B58

A57

LD66

FRDR46TRDR44TFDR43

SFDR41

SRDR42

MDP38

SP–

SP+

M401(SPINDLE) M

CD DSPIC201

SYSTEM CONTROLLERIC801 (1/2)

XTAI 109

XTAO 108

SSTP 39

X20216.9344MHz

S201(LIMIT)

CD +3.3V

CD-LRFACO

AOUT1 112

AOUT2 11770 RFACI71

XRST8

MUTE20

XTACN 7ACK 15 ACK63

A

AUTOMATICPOWER CONTROL

Q321

XTACN67

M-MUTE66

XRST68

IREQ 10REQ 14

XLAT2 13CLOK2 90 CLOK260

XLAT261REQ62IREQ57

DATA2 12

SCOR 26 SCOR56

ODATA259IDATA258

SENS 20XLAT 16CLOK 11DATA 89 DATA19

CLOK20XLAT55SENS18

R-CH

• SIGNAL PATH

: CD PLAY

• R-ch is omitted due to same as L-ch.

53 CD-DOOR

S801(CD LID OPEN/CLOSE DETECT)

(Page 14)

SECTION 5DIAGRAMS

1313

ZS-SN10

ZS-SN10

5-2. BLOCK DIAGRAM – TUNER SECTION –

R COUNT

2

24

4 7

20 21

FMRF AMP

FMMIX

FMOSC

FM IFAMP

IFBUFFER

AFBUFFER

AFAMP MPX MUTE

STEREO/MONO,FM/AMAM IF

AMP

FM DET

AM DET6

FMRF-IN

22AM

RF AMPAMMIX

AMRF-IN

MIX-OUT

OSC-OUT

CF2

FM/AM PLLIC2

CF4

FMRF-OUT

10

QUAD

FMIF-IN 12

1511

L-OUTMPX-IN

R-OUT

13

AMIF-IN

LPF1

/BAN

D

AM O

SC

FM O

SC

FM/AM RF AMP, MIX, OSC,FM/AM IF AMP, DET, MPX

IC1

FM FREQUENCYCOVERAGE

CT1, L1

FM TRACKING

CT3, L3

AM TRACKING

T1AM IFT

LOW-PASSFILTER

LOW-PASSFILTER

• SIGNAL PATH

: FM

: AM

X175kHz

CT3

L1FM RF

XOUT

XIN

AM IN

IF IN

ST-IN

D

LP-O

UT

LP-IN

FM IN

20

19

111218

MW

/LW

6

CT1

D1

L4AMOSC

L2FM OSC

LEVELDET

STIND

14

LPF2

/MO-

ST

AMOSC BUFFER

BUFFER

SWALLOWCOUNTER

UNIVERSALCOUNTER

CCBINTERFACE

REFERENCEDIVIDER

UNLOCKDETECT

12 BITPROGRAMMABLE

DIVIDER

PHASEDETECTOR/

CHARGE PUMP

SHIFT REGISTER & LATCH

1/2

MUTINGQ808

BAND

DI

CL

CE

DO

DET-OUT

ANT1FM TELESCOPIC

ANTENNA

PD

IF-O

UT

ST-IN

D

2

3

1

4

10 9

BAND

7

MO/

ST

13817 16

17 18

16

19

D2

VT B+

D3(1/2)

D3(2/2)

AM IF

• R-ch is omitted due to same as L-ch.

R DATA

R CLOCK

R CE

R-CH

CR MUTING

TU-L B

T2FM IFTFM IF

L3AM FERRITE-ROD

ANTENNA

R DATA, R CLOCK, R CE,R COUNT, R MUTING

AM FREQUENCYCOVERAGE

(Page 14)

(Page 14)

1414

ZS-SN10

ZS-SN10

5-3. BLOCK DIAGRAM – MAIN SECTION –

77RESET

45VH

69VH-CONT

22P-CON

SYSTEM CONTROLLERIC801 (2/2)

+6VREGULATOR

Q954

LED DRIVEQ803

+6VREGULATOR

Q955

B+ SWITCHQ951 – 953

B+ SWITCHQ809, 810

+3.3VREGULATOR

IC802

RESET SIGNALGENERATOR

IC803

REMOTE CONTROLRECEIVER

IC401

DC/DCCONVERTERIC901, Q956

+2.5VREGULATOR

IC202

B+ SWITCHQ813

B+ SWITCHQ804, 806

DC LEVELDETECT

Q821, 822

46VMDC LEVELDETECT

Q811, 812AU +6V

D402(LCD BACK LIGHT)

AMP B+

F902

SYS +3.3V

SYS +3.3V

SW +9V

CD +3.3V CD +6V

SYS +3.3V

CD +2.5V

RADIO +6V

E.VOL B+

RE B+

SYS +3.3V

LOAD CONTROLSWITCH

Q823, 824

24TU-ON

25CD3.3V-ON

433.3V-CHECK

26BUCKUP-ON

WAKE UPSWITCH

Q807

70LOAD

: CD PLAY

: FM

• R-ch is omitted due to same as L-ch.• SIGNAL PATH

D401OPR/BATT

SHIF

T

Q802

Q801, 802SHIFT CLOCK

Q801

X8014.19MHz

X80232.768kHz

X1 X0

7883 82

X1A

X0A

79 80

R-DATAR-CLOCKR-CER-COUNT

30

2829

27

C

R-MUTE31

LCD-DB0 – LCD-DB7

LIQUID CRYSTAL DISPLAYLCD401

85 – 92LC

D-RE

S93

LCD-

RW

94

LCD-

E

95

LCD-

RS

96

BL

100

SDASCL

56

EEP-SDAEEP-SCL

EEPROMIC804

87

R DATA

R DATA, R CLOCK,R CE, R COUNT,R MUTING

R CLOCKR CER COUNTR MUTING

VOL-

CLK

10

VOL-

DATA

9

A-M

UTE

21

MEG

ABAS

S

15

98 JOG-A

64 REMOTE

99 JOG-B

52 WP

40 KEY2

ROTARYENCODER

S401(JOG)

S418 – 424

41 KEY0

S402 – 407

39 KEY1

S410 – 414, 425

R-CH

6

14 13

16

INPUT SELECT,ELECTRICAL VOLUME,

SURROUND/TONE CONTROLIC301SI SC

TU-LB

CD-LA CD-L

1 R-IN

8 RA-L

LCH4SEL L

J322

LINE IN 10 LI-L

POWERAMPIC304

R-CH

R-CH

SP101(L-CH)

SP201(R-CH)

J301

i

R-CH

MEGA BASSCONTROL

Q101

D301

MUTINGQ121

54AC-IN AC CHECKQ805

RECTD901 – 904

T901POWER

TRANSFORMER

DRY BATTERYSIZE "D"

(IEC DESIGNATION R20)6PCS. 9V

J901AC IN

RMC +5V

D801

32VM-CONT

44VOL-CHECK

(Page 12)

(Page 13)

(Page 13)

1515

ZS-SN10

ZS-SN10

• Note for Printed Wiring Boards and Schematic Diagrams

Note on Schematic Diagram:• All capacitors are in µF unless otherwise noted. (p: pF)

50 WV or less are not indicated except for electrolyticsand tantalums.

• All resistors are in Ω and 1/4 W or less unless otherwisespecified.

• f : internal component.• C : panel designation.

• A : B+ Line.• H : adjustment for repair.• Power voltage is dc 4.5V and fed with regulated dc power

supply from pin 1 and 2 of CN902 on the BATTERY 1board, and from pin 3 and 2 as well.no mark : FM⟨⟨ ⟩⟩ : AM( ) : CD PLAY

• Voltages are taken with a VOM (Input impedance 10 MΩ).Voltage variations may be noted due to normal productiontolerances.

• Waveforms are taken with a oscilloscope.Voltage variations may be noted due to normal productiontolerances.

• Circled numbers refer to waveforms.• Signal path.

F : FMf : AMJ : CD PLAYj : LINE IN

• AbbreviationAUS : Australian modelCND : Canadian modelKR : Korean modelMX : Mexican modelSP : Singapore modelTH : Thai modelTW : Taiwan model

Note on Printed Wiring Board:• X : parts extracted from the component side.• Y : parts extracted from the conductor side.• W : indicates side identified with part number.• f : internal component.• : Pattern from the side which enables seeing.

(The other layers' patterns are not indicated.)

Caution:Pattern face side: Parts on the pattern face side seen from(Conductor Side) the pattern face are indicated.Parts face side: Parts on the parts face side seen from(Component Side) the parts face are indicated.

Note:The components identi-fied by mark 0 or dot-ted line with mark 0 arecritical for safety.Replace only with partnumber specified.

Note:Les composants identifiéspar une marque 0 sont cri-tiques pour la sécurité.Ne les remplacer que par unepiéce por tant le numérospécifié.

• Circuit Boards Location

LCD board

CD boardCONTROL (1) board

CONTROL (2) board

BATTERY 2 board

BATTERY 1 board

H/P board

POWER board

TUNER board

MAIN board

Ver. 1.1

1616

ZS-SN10

ZS-SN10

5-4. PRINTED WIRING BOARD – CD BOARD – • See page 15 for Circuit Boards Location. :Uses unleaded solder.

R256

C257

R260

C206

C205

C322

R323

R322

R321 R3

24

C223

C321

C268

C267

R271

R203

C226

R201

C227

C110

C108

C102

C203

C204

C270

C269

C101

IC202

C202

R207

C215

R202

C201 X202

R421

C424

C210

Q321

C207

C275

C323

C406

R401

C401

C219

R276

C271

C272 C104

C105C107

C109

C232

C220

R249

R325 R326

R115

1-865-539-

11

(11)

CD BOARD (COMPONENT SIDE)

E

1

3

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

A

B

C

D

E

F

G

H

I

R423

(Page 20)

C259

R257

C258

C260

C261

R258

R259C208

R101

R265R266

R267

C264

C265

R278

C111

C133

C214

R270

C221

C292

C291R2

92

R291IC201

C217

C132

C218

C224

R451

R102

R103

R104

R105R107

R108

R109

R110

R111

C451

IC402

C256

C251

C252

C254

C253R254

R255

R252

R253

CN301

C213

C222

C405

R113

C404

R452

C112

R275R277

C103

R112

C301

C302

C303C273

R268

C113

CN102

C230 R250

R280

CD BOARD (CONDUCTOR SIDE)

1-865-539-

11

(11)

S201(LIMIT)

M401(SPINDLE)

M

M402(SLED)

M

OPTICAL PICK-UPBLOCK

(KSM-213CDP)

MAIN BOARDCN801

A

1717

ZS-SN10

ZS-SN10

5-5. SCHEMATIC DIAGRAM – CD BOARD – • See page 26 for IC Block Diagram. • See page 26 for Waveforms. • See page 28 for IC Pin Function Description.

R2

59

C208

TP3

C205

R324

R101

C214

R271

R270

R292

C1

10

R451

R102

R103

R104

R105

R107

R108

R109

R110

R111

R255

R253

TP4

C406

C301

R325

R326

R254

R252

R2

50

R2

68

R322

R321

C2

64

CN102

R2

57

CN301

C222

C269

C213

C270

C268C275

C215R203

R291C201

C219

R112

R113

C203

C1

08

C1

02

C1

01

C1

11

C1

04

C1

09

C1

07

R275

R277

R276 C271

C220

C221

C2

73

C2

61

C2

60 C259

R2

65

R266

R267

R2

58

C2

58

R2

60

C256

C207

C254

C253

C252

C251

C232C206

C224

C267

C218

C291

C292

C217

C202

R401C401

C302C303

C322

C321

R323TP1

TP2

R421

C404

IC201

R207 C226

X202

C2

65

R249

C210

R256

C257

C323

Q321

C424

R423

C405

M402

M401

IC402

IC202

C227

S201

TP

C230

TP

C451R452

R115

R2

01

R202 C204

C1

12

C1

13

C1

05

C1

03

R280

C272

R278

C223

C133

C132

10

k

0.1

TEI

0.1

100k

100

0.1

1M

470

100

22

0p

22k

100

100

100

100

100

100

100

100

100

1k

1k

FEI

0.1

0.1

0

0

10k

10k

1M

10

k

2.2

2.2

10

00

p

23P

47

0k

16P

0.1

47 4V

0.1

47 4V

22p5p

0.10

10010010V

0.1

100

100

10010V

22

0p

22

p

22

p

22

0p

22

0p

22

0p

22

0p

100

100

47k 0.1

0.1

0.1

47

0p

0.0

1

0.4

7

100p

4.7

k

1k

4.7k

22

0k

22

0p

0

0.1

100 10V

4700p

470p

4700p

470p

0.1

0.1

0.1

22p

0.1

470p

470p

0.1

0.1

047010V

1010

1

1000p

0APC

SPI

0

0.1

CXD3014-201R

0 1

16.9344MHz

0.1

47k

0.1

22k

0.1

10010V

2SA2119K

0.1

10k

0.1

FAN8040G3

TK73325WTL-G

1

100p

47000p10k

0

0

0 220p

10

0p

10

0p

10

0p

10

0p

0

0.1

100

47p

100p

22p

FR

DR

FFD

R

TR

DR

TFD

R

FRDR

FFDR

TRDR

TFDR

SP

-

SP

+

SL+

SL-

SP+

SP-

SL+

SL-

OP

IN-

OP

IN+

CH

1FIN

CH

1R

IN

CH

2FIN

CH

2R

IN

GN

D

CN

F4

PO

WV

CC

CH

2O

UT

R

CH

2O

UT

F

CH

1O

UT

R

CH

1O

UT

FC

H4

OU

TR

CH

4O

UT

F

CH

3O

UT

F

CH

3O

UT

R

PO

WV

CC

MU

TE

GN

D

CH

3R

IN

CH

3FIN

CH

4IN

CH

4C

AP

A

OP

OU

T

PR

EV

CC

VR

EF

GA

IN-S

W

MIRR

DFCT

FOK

VSS

LOCK

MDP

SSTP

IOVSS1

SFDR

SRDR

TFDR

TRDR

FFDR

FRDR

IOVDD1

AVDD0

AVSS0

E

F

TEI

TEO

FEI

FEO

VC

A

B

C

D

AV

DD

4

RFD

CO

PD

SE

NS

AC

_S

UM

EG

_INLD

PD

RFC

AV

SS

4

RFA

CO

RFA

CI

AV

DD

3

BIA

S

AS

YI

AS

YO

VP

CO

VC

TL

AV

SS

3

CL

TV

FIL

O

FIL

I

PC

O

BC

KI

LR

CK

I

LR

CK

VSS

PC

MD

BC

KVDD

IOVDD2

DOUT

TEST

IOVSS2

XVSS

XTAO

XTAI

XVDD

AVDD1

AOUT1

VREFL

AVSS1

AVSS2

VREFR

AOUT2

AVDD2

IOVDD0

IOV

SS

0

XT

AC

N

XR

ST

VS

S

VD

D

SE

NS

WFC

K

XU

GF

XP

CK

GFS

C2

PO

SC

OR

VD

D

CO

UT

PC

MD

I

CL

OK

SV

SS

SV

DD

SV

SS

SVDD

VSS

SV

DD

VD

D

VS

S

TE

ST

1

SV

SS

SVSS

SVDD

JTAGTCK

JTAGTDI

JTAGTDO

JTAGTMS

TRST

VDD

TES1

PLLVDD

PLLVSS

AC

K

RE

Q

IRE

Q

SR

AM

ST

B

2 31

XL

AT

2

XL

AT

CLOK2

DA

TA

DA

TA

2

T+

VC

GND

LD

PD

F+

T-

F-

VCC

SCOR

SENS

XRST

XTACN

D-OUT

L-OUT

R-OUT

DVDD(3.3V)

AVDD(3.3V)

AGND

DGND

MGND

E

D

A

B

C

F

VR

XLAT

DATA

IN GN

D

OU

T

+2.5V REGULATOR

(LIMIT)

AUTOMATIC

POWER

CONTROL

CD DSP

FOCUS/TRACKING

COIL DRIVER,

SLED/SPINDLE

MOTOR DRIVER

OPTICAL

PICK-UP

BLOCK

(SPINDLE)

(SLED)

(VC)

(RFACO)

KSM-213CDP

CLOK2

M-MUTE

IREQ

CLOK

DATA2

XLAT2

REQ

ACK

6V

(Page 22)

Ver. 1.3

1818

ZS-SN10

ZS-SN10

5-6. PRINTED WIRING BOARD – TUNER BOARD – • See page 15 for Circuit Boards Location. :Uses unleaded solder.

IC2IC1

TUNER BOARD

1-863-438-

11

(11)

L4

L3AM FERRITE-ROD

ANTENNA

L2

T2

T1

L1

(SHIELD CASE)

TP(VT)

TP(GND)

TP(ANT)

ANT1FM TELESCOPIC

ANTENNA

1 2 3 4 5 6 7 8 9 10

A

B

C

D

1

11

C13

JC24

R5

E

F

(US, CND, E, MX)

C78C77

(SP, TW, KR, TH, AUS)

(SP, TW, KR, TH, AUS)

(US, CND, E, MX)

MAINBOARDCN802

B

(Page 20)

Ver. 1.2

1919

ZS-SN10

ZS-SN10

5-7. SCHEMATIC DIAGRAM – TUNER BOARD – • See page 26 for IC Block Diagrams. • See page 26 for Waveform.

CNP1

C20

R30

R31

C34

D2C33C35

C31C30

C24 C22

C23

C37

R52 C53 C65

R91

R50

R10

C29 C27 C26

R61 R60 R59 R58

R92

C61 C62 C63

C66 C68

R94

C51 C52 R51

C59 R53 C95

C55

R54

C54 C56

C57

R65 R63

R4

R13

C1

C11C4

CF4

CF2

C8C10

C12

C9

C47 C39R40R41 C49

C41

C42

C43

R32

D1

C32

D1

1D

10

C60

C80

R24

TP

JC5

JC1

JC4

JC33

JC2

JC6R1

JC13

JC3

JC12 JC11

L2L1

L3L4

IC1

TP

ANT1

TP

T2

C18

D3

IC2

T1

CT1

CT3

R11

C21

R3

X1

R2

L11

C7

JC34

R56

L21

11P

0.1

22k

4.7kR3310k

0.01

KV1471E0.01C130.010.01

22p0.01

220p 0.1

150V

0.01

0 0.22 4.750V

220

1k

47

10010V 100p 100p

2.2k 2.2k 2.2k 2.2k

220

100p 100p 100p

100p 100p

1k

22p 10p 10k

100p 4.7k 1000p

100p

470

22010V 1000p

1000p

10k 10k

10k

1k

47p

0.11000p1000p150V

4.750V

10p

10p 0.1220k10kJC24

0 0.01

220p

100p

22p

100k

KV

14

71

E1000p

1S

S3

55

1S

S3

55

1000p

0.01

220

(GND)

0

0

0

0

0

0470

R51K

0

0

0 0

TA2149BN

(ANT)

(VT)

22010V

KV1520NT

LC72137M-TLM

C14∗

C15∗

∗C14, 150.01 (SP, TW, KR, TH, AUS)0.022 (US, CND, E, MX)

C784700p

C774700p

2.2k

150V

10k

75KHz

470

5p

0

220

A-GND

R-VT

AM

OS

C

FM

OS

C

VC

C1

IF-O

UT

DE

T-O

UT

MP

X-I

N

R-O

UT

L-O

UT

ST

-IN

D

QU

AD

GN

D2

IF-I

N

AM

IF-I

N

FM

VC

C2

AG

C

LP

F1

/BA

ND

LP

F2

/MO

-ST

GN

D1

FM

RF-I

N

RF-O

UT

AM

RF-I

N

FM

OS

C-

OU

T

OU

T

MIX

-

CU

T

AM

LO

W

CE

DI

CL

DO

BA

ND

ST

-IN

D

IF I

N

XO

UT

XIN

LP

-OU

T

LP

-IN

PD

VS

S

VD

D

MO

/ST

FM

IN

AM

IN

MU

TE

AM IFT

FM

OSCFM

RF

ANTENNA AM OSC

FM/AM RF AMP,MIX,OSC,

FM/AM IF AMP,DET,MPX

FM TELESCOPIC

ANTENNA

FM/AM PLL

IFT

FM

AM FERRITE-ROD

R-MUTE

R-COUNT

R-CLOCK

R-DATA

R-CE

TU-L

RADIO 6V

TU-R

S-GND

BA

ND

MW

/LW

1µH

10µH

(US, CND,E, MX)

(US, CND, E, MX)

(SP, TW, KR, TH, AUS)

(SP, TW, KR, TH, AUS)

BMAIN

BOARD(1/2)

CN802(Page 22)

AM FREQUENCYCOVERAGE

FM FREQUENCYCOVERAGE

R141k R55

10K

R57100

11

TUNER

Ver. 1.2

2020

ZS-SN10

ZS-SN10

5-8. PRINTED WIRING BOARDS – MAIN SECTION – • See page 15 for Circuit Boards Location. :Uses unleaded solder.

• SemiconductorLocation

Ref. No. Location

D301 F-3D801 B-11D802 B-12D905 D-6D906 D-5D907 E-6D908 D-10D951 D-6D953 C-7

IC301 I-3IC304 C-3IC801 I-10IC802 F-8IC803 G-10IC804 M-8IC901 C-10

Q101 G-4Q121 F-4Q201 G-4Q221 F-4Q801 G-10Q802 G-9Q803 J-8Q804 J-8Q805 I-12Q806 J-7Q807 L-12Q808 L-11Q809 M-4Q810 M-4Q811 L-11Q812 L-12Q813 M-11Q821 E-13Q822 E-13Q823 C-12Q824 D-13Q951 D-5Q952 C-5Q953 D-5Q954 C-7Q955 C-6Q956 D-10

Q954Q952

Q955C963

C959

C326

C955

C201

C101

C102

C202

C103

C203

C217

C117

C218

C118

C204

C104

C304

C303

C111

C211

C214

C114

C325

C124

C123

C223

C322

C224

C126

C226

CN901

IC304

C953

C954

C956

X802

C803

C870

CN302

C321

X801

JW809

JW815

JW816

JW82

4

JW82

5

JW827

JW828

JW829

JW830

JW831

JW832JW833

JW839

JW84

0

JW84

1

JW842

JW84

3

JW844

JW847

JW848

JW849

JW850

JW852

JW85

3

JW86

4

JW86

6

JW86

7

JW86

8

JW86

9

JW87

0

JW872

JW873

JW875

JW876

JW877JW878

JW88

1

JW88

2

JW88

3

JW88

4

JW888

JW889

JW890

CN802 CN804

CN805

L801

L802

JW80

3

JW86

1

JW858

JW851

JW86

2

JW86

3

CN301

JW85

5

JW898

JW899

JW31

3

JW31

4

JW80

7

JW80

4

JW80

6

JW80

5

JW819

JW808

C950

JW85

9

JW85

4

JW86

0

JW80

2

JW845

JW89

1

JW89

2

JW89

3

JW885

JW886

JW846

JW826

JW811

Q824

JW315

JW316

JW31

8

JW894

JW895

JW89

6

JW813

JW814

JW810

JW874

JW821

JW834

JW81

2

JW31

2

JW823

JW818

C873

JW31

9

JW320

JW32

1

JW85

6

JW85

7JW317

JW86

5

JW835

JW87

1

JW88

7

C874

JW801

JW32

2

L804

CN801

JW879

C301

L806

CN806

CN807

L807

L803

JW82

0

JW82

2

JW311

R468R469R470R471R472R473R474R475R476R477R478R479

Q951

D906

D907

Q809

Q810

IC901Q956

C957

C958

R305

C305

C306

R306

C867

D802

R325

R326

R950

R951

R952R953

R955

R954R957

R958

R956

Q953

R959

R960

R961

R901

R902

R903

D953

C952

C951

C960

D905

C907

C961

R105R205

R206

R106

R110

R111

R210

R211

C207

C107

C106

C206

R301R302

R303

R304

C302

R113

C109

C110

R112

R213

C209

C210R212

R202

R214R215

R216

C212

C213

R220

R114

R115

R116

C112

C113

Q201

C216

R219

R119

Q101C116

R120

R217

R218

R117R118

Q221

R221

R121

Q121

R127

R227C324 R323

R324R309

R321

R122

R123

R222

R223

R322

R125 R225

C871C872

IC803

R894

R893

R891

C869

C801

C423

C424

C425

C426

C427

C428

C429

C430

C431

C432

C433 C4

34

IC301

C802

C805 C831

Q801

Q802

C827C828

C829

C830

C823C824

C825

C826

C821

C822

R895

R896

JC801

JC803

R815

R480 R4

81

C842

Q803

R816

R817

Q804

Q806

R825

R826

R847

R848

C832C833 R801

R802

R803

R805R806

R856

R855

R830

R832

R833

R834

C861C862

R837

R838

R839 R840

R841

C851

C853

R835

R836

C848

C849

C850

R842

C854

C855C856

R850

R849

R851 R859

R862

C838

C840C841

R827R868

R828

R867

R853

R852R866

R865

C820

R854

R899

R811

R877

R844

R858

Q813

R800

R863

R845

R846

Q811Q812

C839

Q808C8

52

Q807

Q805

R829

R864

C837R813

R812

R882

R883

R884

R887R8

88R8

86

C868

JC80

4

JC80

5

JC80

6

JC807C806R818

IC804

C807C808

C809

C810

C812

C813

C814

C815

C816

C817

C818

C819

C811

R831R869

R870

R873

R874R875

R876

R878

R879

R880

R881

D801

D301

C421

C422

C105

C205

R101

R103

R104

R201

R203R204

R102

D951

C108

C208

Q821

Q822

Q823

R495

R496

R497

R498R4

99

JC802

C122

C222

R483 R484

R485 R486

IC801

C125

R124

R224

C225

C875

R488

D908

JC808C120C220

R900

R808

R807

FB80

1

FB80

2

C845

C859

C860

FB80

3

R871

R872

FB80

4

MAIN BOARD

1-866-321-

11

(11)

AA

K

12

43

4 5

3 1

AA

K

TUNERBOARDCNP1

B

LCD BOARDCN405C

LCD BOARDCN402D

S801CD LID

OPEN/CLOSEDETECT

POWERBOARDCN905

H

CDBOARDCN102

A

CONTROL (1)BOARDCN403

E

3

1

IC802

(EXCEPT TW, KR, AUS)

(TW, KR, AUS)

(US, CND, E, MX)

(SP, TW, KR, TH, AUS)

1

4

8

5

C127

C227

R892

L101L301

CN303

J322 J301

CN322

L201 JW303

R126

R226

C119

C219

FB101

FB201

FB301

H/P BOARD

1-86

6-32

4-

11

(11)

SP201(R-CH)

SP101(L-CH)

iLINE IN

A

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17

B

C

D

E

F

G

H

I

J

K

L

M

N

(Page 21)

(Page 16)

(Page 24)

(Page 24)(Page 24)

(Page 18)

Ver. 1.2

2121

ZS-SN10

ZS-SN10

5-9. PRINTED WIRING BOARDS – POWER SECTION – • See page 15 for Circuit Boards Location. :Uses unleaded solder.

CN904

JW903 JW904

CN905

D901

D902

D903

D904

C906

J901

JW901

CN903F902

C901

C902

C903

C904C908

POWER BOARD

1-866-322-

11

(11)

MAINBOARDCN901

H

T901

POWER TRANSFORMER

~AC IN

CN902

JW905JW906

BATTERY2 BOARD

BATTERY1 BOARD

1-866-236-

11

(11)

1-866-235-11

(11)

DRY BATTERYSIZE “D”

(IEC DESIGNATION R20)6PCS. 9V

A

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

B

C

D

E

F

G

H(Page 20)

2222

ZS-SN10

ZS-SN10

5-10. SCHEMATIC DIAGRAM – MAIN SECTION (1/2) – • See page 26 for Waveforms. • See page 31 for IC Pin Function Description.

IC801

Q809

IC804

TP

02

TP

03

Q808

Q811

Q805

CN801

Q806

D801

CN804

Q822

FB801

FB802

FB803

FB804

C842

C421

C422

C831

C853

C862

C861

C833

C832

C806

C848

C849

C850

C852

C854

C841

C840C838

C839

C868

C867

C820

C811

C819

C818

C817

C816

C815

C814

C813

C812

C809

C808

C807

C810

C869

C821

C822

C823

C824

C829

C830

C423

C424

C425

C426

C427

C428

C429

C430

C431

C432

C433

C434

C851

C802C801

C875

C805

C860

C859

C845

C837

C803

C873

L801

L802

L803

L807

L806

X802

IC803

R892

Q810

Q803

Q812

Q807

CN805

IC802

Q802

Q801

Q804

S801

CN802

Q823

Q824

Q821

CN807

CN806

R825

R826

R847

R848

R856

R801

R803

R805

R829

R855R

830

R832

R833

R834

R835

R836

R837

R479

R478

R477

R476

R475

R474

R473

R472

R471

R470

R469

R468

R802

R806

R838

R839

R840

R841

R842

R851

R850

R849

R859

R862

R811

R899

R845R846

R812R813

R844

R863

R882

R884

R883

R886

R887

R888

R828

R864

R807 R808

R865

R868

R827

R831

R869

R870

R873

R874

R875

R876

R877

R878

R879

R880

R881

R894R852R866

R867

R891R893

R896R895

R853 R854

R817 R816

R495

R496

R497

R498

R499

R483

R484

R485

R486

R488

JC802

R872

R871

C870

C874

R480

R481

R815

C826C825

C827C828

C871

C872

C855

C856

D802

JC801

JC803JC805

JC804

JC807

JC806

R818

X801

MB90483BPF-G-153E1

RT1N144M

BR24L16

RT1N144M

RT1N151M-TP-1

RT1N144M

23P

RT1N144M

KDS121-RTK

4P

RT1N151M-TP-1

100p

100p

100p

1

100p

100p

100p

100p

100p

0.1

0.01

1000p

470p

100p

100p

0.01

0.01

0.01

0.01

0.0

1

1000p

0.0

1

100p

100p

100p

22p

22p

100p

100p

100p

100p

100p

100p

100p

100p

1

0.01

0.01

22p

10p

22p

10p

470p

470p

470p

470p

470p

470p

470p

470p

470p

470p

100p

470p

100p

0.010.1

220p

100p

22p

22p

47p

0.01

100010V

S-80828CNNB

220

RT1P144M

2SC4154TP

RT1P151M-TP-1

2SA1602TP

2P

XC6202-33

2SC4154TP

2SC4154TP

RT1P144M

11P

2SC4154TP

KTA1271-Y-AT

RT1P151M-TP-1

11P

11P

1k

1k

1k

1k

10k

10k

10k

10k

1k

10k100

100

1k

1k

1k

1k

1k

4.7k

2.2k

2.2k

2.2k

4.7k

4.7k

4.7k

4.7k

4.7k

4.7k

4.7k

4.7k

10k

10k

1k

1k

2.2

k

1k

1k

1k

1k

1k

0

1k

10k

10k

47k10k

220k220k

22k

10k

4.7

k

4.7

k

4.7

k

220k

220k

220k

47k

47k

470 470

100k1k

1k

220

1k

1k

220

220

1k

1k

1k

100

1k

1k

1k

4.7k47k10k

470k

1k47k

10k

1k

10k 10k

4.7k 4.7k

4.7

k

2.2k

100k

10

220

2.2k

2.2k

2.2k

2.2k

10k

0

1k

1k

10 50V

22010V

1k

1k

4.7k

47p220p

220p47p

22p

22p

1

1

UDZSTE-175.1B

0

00

0

0

0

22k

4.19MHz

CD

3.3

V-O

N

P-C

ON

A-M

UT

E

V-C

LK

ME

GA

BA

SS

CD

3.3

V

V-D

AT

A

AU

-6.0

V

A-G

ND

CD-6.0V

MD-GND

AC

-HI

BA

TT

-CO

M

VD

D(S

W)

CD-L

CD-R

D-GND1

D-G

ND

2

+B

R-VT

S-G

ND

BA

CK

UP

-ON

U-C

OM

3.3

V

TU-L

TU-R

VOL-CHK

KEY0

CL

OK

DA

TA

XR

ST

XT

AC

N

M-M

UT

E

AC

K

RE

Q

XL

AT

2

CL

OK

2

OD

AT

A2

IDA

TA

2

IRE

Q

SC

OR

XL

AT

KEY2

KEY1

KE

Y0

KEY1

KEY2

DATA

CLOK2

M-MUTE

L-OUT

R-OUT

XTACN

XRST

IREQ

IDATA2

CLOK

XLAT2

REQ

ACK

XLAT

SCOR

ODATA2

L-OUT

R-OUT

SENS

SENS

R-CE

R-DATA

R-CLOCK

R-COUNT

R-MUTE

TU-L

RADIO 6V

TU-R

A-GND

R-VT

S-GND

D-GND2

VDD(SW)

KEY0

(1/2)

WAKE UP SWITCH

AC CHECK

DATA

D-OUT

DGND

L-OUT

AGND

R-OUT

XTACN

XRST

XLAT

SENS

SCOR

VDD

WP

SCL

SDAGND

A2

A1

A0

VSS

X0

X1

VCC3

VS

S

VC

C5

AVRH

AVCC

AVSS

VSS

X0A

X1A

NC

NC

NC

NC

NC

NC

NC

NC

NC

NC

NC

NC

EEPROM-SEL

CLOK2

M-MUTE

IREQ

CLOK

XLAT2

REQ

ACK

MD-GND

CD-6.0V

DATA2

DVDD(3.3V)

AVDD(3.3V)

OPEN/CLOSE

CD LID

DETECT

SH

IFT

RES

ET

NC

LO

AD

VH

-CO

NT

XR

ST

XTA

CN

M-M

UTE

NC

REM

OTE

AC

K

REQ

XLA

T2

CLO

K2

OD

ATA

2

IDA

TA

2

IREQ

SC

OR

XLA

T

AC

-IN

CD

-DO

OR

WP

MD

2

MD1

MD0

P81

P80

VM

VH

VOL-CHECK

3.3V-CHECK

KEY0

KEY2

KEY1

NC

NC

VM-CONT

R-MUTE

R-C

E

R-C

LO

CK

R-D

AT

A

R-C

OU

NT

BA

CK

UP

-ON

CD

3.3

V-O

N

TU

-ON

P-C

ON

A-M

UT

E

CL

OK

DA

TA

SE

NS

TE

ST

B

TE

ST

A

ME

GA

BA

SS

SH

IMU

KE

3

SH

IMU

KE

2

SH

IMU

KE

1

VO

L-C

LK

VO

L-D

AT

A

EE

P-S

DA

EE

P-S

CL

LCD-DB0

LCD-DB1

LCD-DB2

LCD-DB3

LCD-DB4

LCD-DB5

LCD-DB6

LCD-DB7

LCD-RES

LCD-RW

LCD-E

LCD-RS

SYSTEM CONTROLLER

JOG-A

JOG-B

BL

Q821,822

DC LEVEL DETECT

1

1

Q823,824

LOAD CONTROL

SWITCH

RESET SIGNAL

GENERATOR

NC

GND

RST

VCC

Q801,802

SHIFT CLOCK

32.768kHz

LCD-DB0

BL 6V

LCD-DB1

LCD-DB2

LCD-DB3

LCD-DB4

LCD-DB5

LCD-DB6

LCD-DB7

LCD-E

LCD-RW

LCD-RS

LCD-RES

LCD-3.3V

D-GND

REMOTE

JOG-A

JOG-B

KEY2

BL-CONT

KEY1

RMC-VCC

+3.3V REGULATOR

Q804,806

B+ SWITCH

GN

D

OU

T

IN

LED

DRIVE

(TW,KR,AUS)

MUTING

Q809,810

B+ SWITCH

Q811,812

DC LEVEL DETECT

EEPROM

(SP,TW,KR,TH,AUS)

EXCEPT

TW,KR,AUS

(US,CND,E,MX)

47 6.3V(US,CND,E,MX)

47 10V(SP,TW,KR,TH,AUS)

47µH

0.22µH

10µH

1µH

Ver. 1.3

2323

ZS-SN10

ZS-SN10

5-11. SCHEMATIC DIAGRAM – MAIN SECTION (2/2) – • See page 27 for IC Block Diagrams.

IC301

J301

CN901

CN323

F902

J901

CN902

Q951

D951

Q953

IC901

D301

CN301 CN322

CN905

Q201

J322

FB301

FB101

FB201

R224 R124R112

R953

R952

R950

R951

R956

R957R958

R954

R955

R959

R960

R961

R903

R902

R901

R305

R306

R900

R113 R213

R212

R302

R301

R303R304

R222

R223

R322

R800

R858

R325

R219

R119

R121

R221

R326

R126

R226

R214

R122

R117

R217

R115

R215

R323

R225

R125

R127 R227

R123

R220

R120

R324

R202R309

R106

R206

R105 R205

R101

R201

R204R103

R203

R116

R114

R216

R104

R111

R211

R110

R210

R102

R321

R118

R218

C303 C301

C114

C214

C204

C104

C218

C118

C217

C117

C202

C102

C201

C101

C103C203

C111

C304

C211

C325

C326

C123 C322C223

C224 C124 C126

C226

C906

C950

C954

C956

C955

C963

C953

C959

C321

D906

D903

D904

D901

D902

D907

D908

JC808

T901

IC304

CN904

Q954

Q955

CN303CN302

CN903

Q813

Q952

Q121 Q221

Q956

Q101

C109

C209

C210

C108

C208

C302

C110

C206

C106

C951

C952

C960

C907

C961

C957

C958

C205

C105

C122 C222

C225 C125

C116

C216

C112

C213

C107

C207

C324

C902

C901

C903

C904

C212

C113

C306

C305

C220

C908

L804

L301

L101

L201

D953

D905

C120

C219

C119

C127

C227

SP101

SP201

BD3870FS

4P

4P

4P

RT1N436M-TP-1

KD

S120-R

TK

2SC4154TP

S-816A33AMC

KDS121-RTK

4P 4P

4P

2SC4154TP

2.2 2.24.7k

2.2

k

2.2

k

2.2

k

2.2

k

47k

2.2k2.2k

10k

10k

1k

1k

1k

1k

1k

1k

1k

1k

1k

470k 470k

4.7k

100

100

10k10k

220

470

1k

470k

47k

1k

4.7k

4.7k

4.7

k

4.7k

1k

100

100

2.2k

220

470

470

1k

1k

10k

4.7k

4.7

k

0 0

470

47k

47k

1M

2.2k10k

47k

47k

10k 10k

10k

10k

1k2.2k

2.2k

220

2.2k

220

1k

1k

1k

10k

10k

2.2

k

2.2k

0

0

0.4750V 100

10V

150V

150V

4.7 50V

4.7 50V

1 50V

1 50V

1 50V

1 50V

2.2

50V

2.2

50V

2.2

50V

2.2

50V

0.4750V

0.4750V

4.750V

4710V

4.750V

1050V

22016V

4710V

4710V

4710V

100

10V

10010V

100010V

100010V

1050V

470016V

100

10V

100

10V

220

10V

10

50V

220

10V220

16V

2225V

ISS355TE-17

1N4002B

1N4002B

1N4002B

1N4002B

1S

S355TE-1

7

ISS355-TE

0

BA5417

2P

2SD2394-F

KTC3203-Y

3P3P

3P

2SA1602TP

KTA1273Y

DTC143TUA DTC143TUA

2SB798

2SC4154TP

0.1

0.1

0.1

2200p

2200p

0.0

1

0.1

1000p

1000p

0.01

0.0

1

0.0

1

0.0

1

0.0

1

0.1

0.1

1000p

1000p

1000p 1000p

0.1 0.1

2200p

2200p

0.0047

0.0022

1000p

1000p

0.22

0.022

0.022

0.022

0.022

0.0047

0.0022

100p

100p

100p

0.22

UD

ZS

TE-1

76.8

B

UD

ZS

TE-6

.8B

100p

1000p

1000p

100p

100p

(L-CH)

(R-CH)

D-GND1

AU-6.0V

MEGA BASS

A-GND

TU-R

P-CON

A-MUTE

VDD(SW)

BATT-COM

+B

D-GND2

AC-HI

CD-R

TU-L

CD-L

R-VT

S-GND

MD-GND

V-DATA

CD 3.3V

CD3.3V-ON

CD-6.0V

V-CLK

VOL-CHK

BACKUP-ON

U-COM3.3V

GND

VDD

GND

BATT

BATT

VDD

GND

R I

N

L I

N

SE

L R

SE

L L

CD

-R

CD

-L

RA

-R

RA

-L

LI-

R

LI-

L

FIL

TE

R

GN

D

CA

P

TN

FR

TN

FL

BN

FL

BO

L

BN

FR

BO

R

RC

H

LC

H

VC

C

SI

SC

BATT-COM

BATT-COM

AC-HI

BATT-COMBATT-COM

AC-HI

GND

GN

D

(2/2)

INPUT SELECT,

ELECTRICAL

VOLUME,

SURROUND/

TONE

CONTROL

Q101,201

MEGA BASS CONTROL

PR

EG

ND

2

PR

EG

ND

1

FILTER ST

BY

POWER

GND BS

R

VC

C

BS

L

NC

POWER AMP

Q121,221

MUTING

B+ SWITCH

+3.3V REGULATOR +6V REGULATOR

+3.3V REGULATOR

+6V REGULATOR

Q951-953

B+ SWITCH

LINE IN

EX

T

OU

T

IN

ON

/OFF

BATT-COM

POWER TRNASFORMER

DRY BATTERY

SIZE"C"

(IEC DESIGNATION R14)

6PCS. 9V

LINE-L

A-GND

LINE-R

LINE-L

A-GND

LINE-R

L

GND

R

GND

T2AL 250V(SP,KR,TH,AUS)

2.5A 125V(US,CND,E,MX,TW)

47µH

47µH

1µH

47µH

Ver. 1.3

2424

ZS-SN10

ZS-SN10

5-12. PRINTED WIRING BOARDS – PANEL SECTION – • See page 15 for Circuit Boards Location. :Uses unleaded solder.

S410

S411

S413

S414

S418

S419

S420 S421

S423

D402(LCD BACK LIGHT)

L402

JW40

2

JW403

S424S422

S412

S425

L401

CN402CN405

L403

R436

R437

R438

R439

R440

R493

R494

R446

R447

R448

R449

R450

C401

C402

C403

R458

R459

R415

R416

C405

C406

R401

R402

C419

C420

R491

R451R452R453 R454

C404

C407

C408

C409

C410

C411

C412

C413

C414

R490R492

R417

C417

C418

LCD BOARD

1-866-323-

11

(11)

MAIN BOARDCN807 C MAIN BOARD

CN806D

1

1

3

22

LCD401LIQUID CRYSTAL DISPLAY

RADIO/BANDAUTO PRESET

IC401

>

PRESET+

.

PRESET–

u

x

LINEDISPLAYREPEAT MODE

SEARCH

–/ TUNE

+/ TUNE

ENTER/MEMORY

1

3

S401ROTARY

ENCODER(JOG)

S402 – 407,S410 – 414,S418 – 424

CN401

CN403

S402

S403D401

R418R419

R420R421

R425

R426 R427

CONTROL (1)

1-866-327-

11

(11)

MAIN BOARDCN804E

SLEEP

POWER

OPR/BATTS404S405

CN404

S407 S406

R428R429

R430

R431R432

CONTROL (2)

1-867-694-

11

(11)

SOUND MEGA BASS– +VOLUME

A

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

B

C

D

E

F

G

H

I

J

(Page 20) (Page 20)

(Page 20)

2525

ZS-SN10

ZS-SN10

5-13. SCHEMATIC DIAGRAM – PANEL SECTION –

R437

R427

R417

C401R492

R490

R491C407

C408

C409

C410

C411

C412

C413

C414

C417

C418

C404

C403

C402

C406

R415

R416

R458

C420

R494R493R438 R439R436

R454R453

S424

R452

S422

R450R449R448R447R446

CN405

R432R431R430

S405

R429

S404

R428CN404

R425

R421

R420R418

R419

S403

R426

S402

IC401

R401

C419

CN403

R440

R451

LCD401

L40147µH

L403

L402

R459

D402

S401

CN402

R402

S423S418 S419 S420 S421

S411 S412 S413 S414 S425

CN401

D401

S407S406

C405

S410

470

470

470k

110k

2.2k

0

47p

47p

47p

47p

47p

47p

47p

47p

47p

47p

1 1 1

0.01

47k

100k

470

0.01

2.2k1k1k 1k220

4.7k2.2k1k2.2k1k1k470220

11P

2.2k1k2.2k1k1k2P

220

1k

1k470

470

220

RPM7140

1k

0.01

4P

2.2k

2.2k

11P

1k2P

L-34HD470p

*

*

SW 9V

KEY0

D-GND2

D-GND2

*R459

220

470

(WHITE:US,CND)

(EXCEPT WHITE:US,CND)

(WHITE:US,CND)

(EXCEPT WHITE:US,CND)

*D402

SLI-343YC3F

SLR343EBT

(LCD BACK LIGHT)

B GNDA

ROTARY ENCODER(JOG)

DISPLAYMODE

PRESET –PRESET +

LINE /TUNE

+

/TUNE

–

ENTER/

MEMORY

POWER SLEEP

OPR/BATT

KEY0

SOUNDMEGA BASSVOLUME

–

VOLUME

+

KEY0

D-GND2

SEARCH

REPEAT

RADIO/BAND

AUTO

PRESET

D-GND2

1µH

1µH

(Page 22)

(Page 22)

(Page 22)

Ver. 1.3

2626

ZS-SN10

ZS-SN10

• Waveforms

– CD Board –IC402 FAN8040G3

• IC Block Diagrams

– CD Board –

ws IC801 id (X1)

1 V/DIV, 100 ns/DIV

239 ns3.7 Vp-p

qa IC2 w; (XOUT)

500 mV/DIV, 5 µs/DIV

13.3 µs0.9 Vp-p

wa IC801 ul (X1A)

1 V/DIV, 10 µs/DIV

30.5 µs3.5 Vp-p

3 IC201 u; (RFACO)(CD PLAY mode)

200 mV/DIV, 500 ns/DIV

0.5 to 1.1 Vp-p

22.8 µs

3.3 Vp-p

1 IC201 1 (LRCK)(CD PLAY mode)

1 V/DIV, 10 µs/DIV

2 IC201 5 (BCK)(CD PLAY mode)

1 V/DIV, 200 ns/DIV

472 ns3.3 Vp-p

4 IC201 <z/, (XTAO)(CD PLAY mode)

1 V/DIV, 20 ns/DIV

59.4 ns

2.3 Vp-p

– TUNER Board – – MAIN Board –

IC1 TA2149BN

– TUNER Board –

1

LEVEL SHIFT

MUTING D

1516

+ –

+–

DD

1718

D

1920

VREF

2122232425262728

PREV

CC

OPOU

T

OUTV

REF

CH4C

APA

CH4I

N

CH3F

IN

CH3R

IN

GND

MUT

E

POW

VCC

CH3O

UTF

CH3O

UTR

CH4O

UTF

CH4O

UTR

OPIN

–

2

OPIN

+

INTERFACE

1413

D

1211

D

109876

CH2F

IN

CH2R

IN

GND

54

CH1F

IN

CH1R

IN

VREF

IN

POW

VCC

CH2O

UTR

CH2O

UTF

CH1O

UTR

CH1O

UTF

INTERFACE

D D

3

SW

INTERFACE

RF GND

3

2

1

IF REQ

AMMIX

FM RFIN

AM LOW CUT

5

4MIX OUT

VCC

AM IF IN

8

7

6

FM IF IN

GND

10

9AGC

QUAD

12

11R-OUT

L-OUT

FM RFOUT

22

23

24

20

21

17

18

19

15

16

13

14

AM RFIN

RF VCC

FM OSC

ST LED

OSC OUT

AM OSC

IF REQ

LPF1

MPX IN

DET OUT

LPF2

FMMIX

FMOSC

LEVELDET

AMDET

MUTE

FMDET

ST/MOFM/AM

AMOSC

AGC

SW

ST

1/8

BUFFBUFF

DIVIDE

DECODE

VCO

IF BUFF

AF BUFF

AF

FM RF

AM IF

FM IF

1/1 OR1/16

11

10

9

8

7

6

5

4321

12

13

14

15

16

19

20

UNLOCKDETECTOR

POWER ONRESET

UNIVERSALCOUNTER

CCBI/F

CEDICLDO

XOUT

AOUT

XIN

AINPD

VSS

VDD

B04

FMIN

AMIN

B01

B02

B03

I01

I02

IFIN

PHASEDETECTORCHARGEPUMP

REFERENCEDIVIDER

SWALLOWCOUNTER1/16,1/17

4BITS

12BITSPROGRAMMABLE

DIVIDER

DATA

SHI

FT R

EGIS

TER

LATC

H

1/2

1718

IC2 LC72137M-TLM-E

Ver. 1.3

27

ZS-SN10

IC301 BD3870FS-E2

– MAIN Board –

IC901 S-816A33AMC-BAI-T2-G

32

5

OVERCURRENTPROTECTCIRCUIT

REFERENCEVOLTAGE

ERRORAMP

SINKDRIVER

4

1

VOUT

VIN

ON/O

FF

VSS

EXT

SOURCEPOWERSUPPLY

28

ZS-SN10

• IC Pin Function DescriptionCD BOARD IC201 CXD3014-201R (CD DSP)

Pin No. Pin Name I/O Description

1 LRCK O L/R sampling clock signal output terminal

2 LRCKI I L/R sampling clock signal input terminal

3 PCMD O Serial data output terminal

4 PCMDI I Serial data input terminal

5 BCK O Bit clock signal output terminal

6 BCKI I Bit clock signal input terminal

7 XTACN IOscillation circuit on/off switch control signal input from the system controller

“H”: self-oscillation, “L”: oscillation stop

8 XRST I Reset signal input from the system controller “L”: reset

9 VSS — Ground terminal

10 IREQ I Codec data request signal input from the system controller

11 CLOK I CD serial data transfer clock signal input from the system controller

12 DATA2 I/O Codec serial data input/output with the system controller

13 XLAT2 I Codec serial data latch pulse input from the system controller

14 REQ I Codec chip select signal input from the system controller

15 ACK I Codec acknowledge signal input from the system controller

16 XLAT I CD serial data latch pulse input from the system controller

17 VDD — Power supply terminal (+2.5V)

18 SVSS — Ground terminal

19 SVDD — Power supply terminal (+2.5V)

20 SENS O SENS signal output to the system controller

21 WFCK — Not used

22 XUGF — Not used

23 XPCK — Not used

24 GFS — Not used

25 C2PO — Not used

26 SCOR O Subcode sync (S0+S1) detection signal output to the system controller

27 VDD — Power supply terminal (+2.5V)

28 COUT — Not used

29 SVSS — Ground terminal

30 SVDD — Power supply terminal (+2.5V)

31 MIRR — Not used

32 DFCT — Not used

33 FOK — Not used

34 VSS — Ground terminal

35 VDD — Power supply terminal (+2.5V)

36 VSS — Ground terminal

37 MIRR — Not used

38 MDP O Spindle motor servo control signal output terminal

39 SSTP I Disc inner position detection signal input terminal

40 IOVSS1 — Ground terminal

41 SFDR O Sled servo drive signal (+) output to the coil/motor drive

42 SRDR O Sled servo drive signal (–) output to the coil/motor drive

43 TFDR O Tracking servo drive signal (+) output to the coil/motor drive

44 TRDR O Tracking servo drive signal (–) output to the coil/motor drive

45 FFDR O Focus setvo drive signal (+) output to the coil/motor drive

46 FRDR O Focus servo drive signal (–) output to the coil/motor drive

29

ZS-SN10

Pin No. Pin Name I/O Description

47 IOVDD1 — Power supply terminal (+3.3V)

48 AVDD0 — Power supply terminal (+3.3V)

49 AVSS0 — Ground terminal

50 E I E signal input from the optical pick-up block

51 F I F signal input from the optical pick-up block

52 TEI I Tracking error signal input terminal

53 TEO O Tracking error signal output terminal

54 FEI I Focus error signal input terminal

55 FEO O Focus error signal output terminal

56 VC O Middle point voltage output terminal

57 A I A signal iuput from the optical pick-up block

58 B I B signal input from the optical pick-up block

59 C I C signal iuput from the optical pick-up block

60 D I D signal input from the optical pick-up block

61 AVDD4 — Power supply terminal (+3.3V)

62 RFDCO O Not used

63 PDSENS I Not used

64 AC_SUM O RFAC summing amplifier signal output terminal

65 EQ_IN I RF equalizer circuit input terminal

66 LD OLaser diode on/off control signal output to the automatic power control circuit

“L”: laser off, “H”: laser on

67 PD I Light amount monitor input from the optical pick-up block laser diode

68 RFC I Equalizer cut off frequency adjustment terminal

69 AVSS4 — Ground terminal

70 RFACO O EFM signal output terminal

71 RFACI I EFM signal input terminal

72 AVDD3 — Power supply terminal (+3.3V)

73 BIAS I Asymmetry circuit constant current input terminal

74 ASYI I Playback EFM asymmetry comparator voltage input terminal

75 ASYO O Playback EFM full-swing output terminal

76 VPCO O Charge pump output terminal for broad-band EFM PLL

77 VCTL I VCO2 control voltage input terminal for broad-band EFM PLL

78 AVSS3 — Ground terminal

79 CLTV I VCO1 control voltage input terminal for multiplier

80 FILO O Filter output terminal for master PLL

81 FILI I Filter input terminal for master PLL

82 PCO O Charge pump output terminal for master PLL

83 SVSS — Ground terminal

84 SVDD — Power supply terminal (+2.5V)

85 SRAMSTB I Codec standby on/off control signal input terminal Not used

86 VDD — Power supply terminal (+2.5V)

87 VSS — Ground terminal

88 TEST1 I For test terminal Normally fixed at “L”

89 DATA I CD serial data input from the system controller

90 CLOK2 I Codec serial data transfer clock signal input from the system controller

91 SVSS — Ground terminal

92 SVDD — Power supply terminal (+2.5V)

93 JTAGTCK — Not used

94 JTAGTDI — Not used

30

ZS-SN10

Pin No. Pin Name I/O Description

95 JTAGTDO — Not used

96 JTAGTMS — Not used

97 TRST — Not used

98 VSS — Ground terminal

99 VDD — Power supply terminal (+2.5V)

100 IOVDD2 — Power supply terminal (+3.3V)

101 DOUT O Digital audio signal output terminal Not used

102 TEST I For test terminal Normally fixed at “L”

103 TES1 I For test terminal Normally fixed at “L”

104 IOVSS2 — Ground terminal

105 PLLVDD — Power supply terminal (+2.5V)

106 PLLVSS — Ground terminal

107 XVSS — Ground terminal

108 XTAO O System clock output terminal (16.9344 MHz)

109 XTAI I System clock input terminal (16.9344 MHz)

110 XVDD — Power supply terminal (+2.5V)

111 AVDD1 — Power supply terminal (+3.3V)

112 AOUT1 O L-ch analog audio signal output terminal

113 VREFL O L-ch reference voltage output terminal

114 AVSS1 — Ground terminal

115 AVSS2 — Ground terminal

116 VREFR O R-ch reference voltage output terminal

117 AOUT2 O R-ch analog audio signal output terminal

118 AVDD1 — Power supply terminal (+3.3V)

119 IOVDD0 — Power supply terminal (+3.3V)

120 IOVSS0 — Ground terminal

31

ZS-SN10

Pin No. Pin Name I/O Description

1 to 6 NC — Not used

7 EEP-SCL O Serial clock signal output terminal to the EEPROM

8 EEP-SDA I/O Two-way serial data bus with the EEPROM

9 VOL-DATA O Serial data output to the electrical volume

10 VOL-CLK O Serial data transfer clock signal output to the electrical volume

11 VSS — Ground terminal

12 to 14 SIMUKE1 to SIMUKE3 I For destination setting terminal

15 MEGABASS O MEGABASS on/off control signal output terminal

16 TESTA I For CD test setting terminal Fixed at “H” in this set

17 TESTB I For LCD test setting terminal Fixed at “H” in this set

18 SENS I Internal status (SENSE) signal input from the CD DSP

19 DATA O Serial data output to the CD DSP

20 CLOK O Serial data transfer clock signal output to the CD DSP

21 A-MUTE O Audio muting on/off control signal output terminal “H”: muting

22 P-CON O Power control signal output terminal “H”: active

23 VCC5 — Power supply terminal (+3.3V)

24 TU-ON O Tuner power on/off control signal output terminal “H”: tuner on

25 CD3.3V-ON O CD power on/off control signal output terminal “H: CD on

26 BACKUP-ON O CD power select signal output terminal for power off state “L”: power off state

27 R-COUNT I PLL serial count data input terminal

28 R-DATA O PLL serial data output terminal

29 R-CLOCK O PLL serial data transfer clock signal output terminal

30 R-CE O PLL chip enable signal output terminal

31 R-MUTE O Tuner muting on/off control signal output terminal “H”: active

32 VM-CONT O Battery middle voltage (+4.5V) detection circuit control signal output terminal

33, 34 NC O Not used

35 AVCC — Power supply terminal (+3.3V) (for A/D converter)

36 AVRH I Reference voltage input terminal (+3.3V) (for A/D converter)

37 AVSS — Ground terminal (for A/D converter)

38 NC O Not used

39 KEY1 I Key input terminal (A/D input)

40 KEY2 I Key input terminal (A/D input)

41 KEY0 I Key input terminal (A/D input)

42 VSS — Ground terminal

43 3.3V-CHECK I CD power voltage detection signal input terminal

44 VOL-CHECK I Electrical volume power voltage detection signal input terminal

45 VH I Battery high voltage (+9V) detection signal input terminal

46 VM I Battery middle voltage (+4.5V) detection signal input terminal

47, 48 P80, P81 I Not used

49 to 51 MD0 to MD2 I For mode setting terminal

52 WP I Key interruption processing start signal input terminal

53 CD DOOR I CD lid open/close detection switch input terminal “L”: CD lid is close

54 AC-IN I AC voltage detection signal input terminal “L”: AC in

55 XLAT O Serial data latch pulse output to the CD DSP

56 SCOR I Subcode sync (S0+S1) detection signal input from the CD DSP

57 IREQ I Codec data request signal input from the CD DSP

58 IDATA2 I Codec serial data input from the CD DSP

59 ODATA2 O Codec serial data output to the CD DSP

MAIN BOARD IC801 MB90483BPF-G-153E1 (SYSTEM CONTROLLER)

Ver. 1.3

32

ZS-SN10

Pin No. Pin Name I/O Description

60 CLOK2 O Codec serial data transfer clock signal output to the CD DSP

61 XLAT2 O Codec serial data latch pulse output to the CD DSP

62 REQ O Codec data request signal output to the CD DSP

63 ACK I Codec acknowledge signal input from the CD DSP

64 REMOTE I Remote control signal input terminal

65 NC O Not used

66 M-MUTE O Muting on/off control signal output to the coil/motor drive “H”: active

67 XTACN OOscillation circuit on/off switch control signal output to the CD DSP

“H”: self-oscillation, “L”: oscillation stop

68 XRST O System reset signal output to the CD DSP “L”: reset

69 VH-CONT O Battery high voltage (+9V) detection circuit control signal output terminal

70 LOAD O Load control signal output for battery check state

71 to 76 NC O Not used

77 RESET I System reset signal input from the reset signal generator “L”: reset

78 SHIFT O Shift point terminal for oscillation frequency change

79 X1A O Sub system clock output terminal (32.768 kHz)

80 X0A I Sub system clock input terminal (32.768 kHz)

81 VSS — Ground terminal

82 X0 I Main system clock input terminal (4.19 MHz)

83 X1 O Main system clock output terminal (4.19 MHz)

84 VCC3 — Power supply terminal (+3.3V)

85 to 92 LCD-DB0 to LCD-DB7 I/O LCD parallel data input/output terminal

93 LCD-RES O LCD reset control signal output terminal “L”: reset

94 LCD-RW O LCD chip data read/write signal output terminal

95 LCD-E O LCD data enable signal output terminal

96 LCD-RS O LCD resistor select signal output terminal

97 EEPROM-SEL I EEPROM setting terminal Fixed at “L” in this set

98, 99 JOG-A, JOG-B I Jog dial pulse input from the rotary encoder (JOG)

100 BL O LCD back light on/off control signal output terminal “H”: back light on

33

ZS-SN10SECTION 6

EXPLODED VIEWS

NOTE:• -XX and -X mean standardized parts, so they

may have some difference from the originalone.

• Items marked “*” are not stocked since theyare seldom required for routine service.Some delay should be anticipated whenordering these items.

• The mechanical parts with no referencenumber in the exploded views are not supplied.

• Accessories are given in the last of electricalparts list.

• Color Indication of Appearance PartsExample:KNOB, BALANCE (WHITE) . . . (RED) R R

Parts of Color Cabinet’s Color• Abbreviation

AUS : Australian modelCND : Canadian modelKR : Korean modelMX : Mexican modelSP : Singapore modelTH : Thai modelTW : Taiwan model

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark

6-1. CABINET SECTION

1 2-582-114-01 LID, BATTERY (BLACK)1 2-582-114-11 LID, BATTERY (WHITE)1 2-582-114-21 LID, BATTERY (SILVER)2 3-040-916-01 FOOT (FRONT), RUBBER3 3-254-144-01 SCREW (B3), (+) BV TAPPING

(for WHITE, SILVER)

3 3-254-144-11 SCREW (B3), (+) BV TAPPING (for BLACK)4 3-252-833-01 SCREW (M3), (+) P5 2-582-130-01 WINDOW, LCD (for BLACK, WHITE)5 2-582-130-21 WINDOW, LCD (for SILVER)6 1-831-915-11 CABLE, FLEXIBLE FLAT (4 CORE)

7 3-252-827-01 SCREW (B2.6), (+) BV TAPPING

8 A-1105-346-A MAIN BOARD, COMPLETE (US, CND, E, MX)8 A-1105-348-A MAIN BOARD, COMPLETE (SP, TH)8 A-1105-349-A MAIN BOARD, COMPLETE (TW, KR, AUS)9 2-024-906-01 CUSHION (REAR)

10 3-018-963-01 CUSHION (BATTERY CASE LID)11 3-577-414-01 SPACER (for BLACK)11 3-577-414-11 SPACER (for WHITE, SILVER)12 2-594-013-01 PLATE (MAIN), SHIELD13 3-254-144-01 SCREW (B3), (+) BV TAPPING

14 4-017-441-01 CUSHION (B) (for BLACK)14 4-017-441-31 CUSHION (B) (for WHITE, SILVER)ANT1 1-754-241-11 ANTENNA, TELESCOPIC

5

13

3

1

11

2

cabinet front section MAIN board

3

410

3

3

cabinet top section

ANT1

cabinet bottomsection

notsupplied

14

6

12

8

7

13

13

9

9

The components identified by mark 0 ordotted line with mark 0 are critical for safety.Replace only with part number specified.

Les composants identifiés par une marque 0sont critiques pour la sécurité.Ne les remplacer que par une pièce portant lenuméro spécifié.

Ver. 1.4

34

ZS-SN10

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark

6-2. CABINET FRONT SECTION

56

55

5554

53

51

67

65

65

64

6059

57

58

5469

64

63 62

notsupplied

notsupplied

(for SILVER)

notsupplied

notsupplied

SP101

SP201

IC401

LCD401

LCD board

61

54

66

66

66

7070

71

72

7073

52

66 66

66

68

6968

68

Ver. 1.4

51 2-582-140-01 BOX (R), SPEAKER52 X-2050-833-1 CABI (FRONT) SUB ASSY (BLACK) (US)52 X-2050-834-1 CABI (FRONT) SUB ASSY (WHITE) (US)52 X-2050-835-1 CABI (FRONT) SUB ASSY (BLACK) (CND)52 X-2050-836-1 CABI (FRONT) SUB ASSY (WHITE) (CND)

52 X-2050-837-1 CABI (FRONT) SUB ASSY (SILVER)(EXCEPT US)

52 X-2109-390-1 CABINET (FRONT) SUB ASSY (SILVER) (US)53 2-582-115-01 BUTTON (CD) (BLACK)53 2-582-115-11 BUTTON (CD) (WHITE)53 2-582-115-21 BUTTON (CD) (SILVER)

54 3-254-151-01 SCREW (B2.6), (+) P TAPPING55 3-254-143-01 SCREW (B3), (+) BV TAPPING56 2-582-139-01 BOX (L), SPEAKER57 A-1105-337-A LCD BOARD, COMPLETE (for BLACK, SILVER)57 A-1124-479-A LCD BOARD, COMPLETE (for WHITE)

58 2-582-131-01 HOLDER (LCD)59 2-582-138-03 PLATE, LIGHT GUIDE60 2-582-152-01 ILLUMINATOR61 3-252-827-01 SCREW (B2.6), (+) BV TAPPING62 2-582-133-01 HOLDER (JOG)

63 2-582-127-01 KNOB (JOG) (BLACK)63 2-582-127-11 KNOB (JOG) (WHITE)63 2-582-127-21 KNOB (JOG) (SILVER)64 1-831-926-11 CABLE, FLEXIBLE FLAT (11 CORE)65 3-254-144-01 SCREW (B3), (+) BV TAPPING

66 2-024-906-01 CUSHION (REAR)67 2-633-236-01 CUSHION (TUNER FFC)68 3-357-572-01 CUSHION69 3-885-228-01 CUSHION (B)70 4-942-511-01 SPACER

71 X-2059-969-1 PANEL SUB ASSY (for BLACK)71 X-2059-970-1 PANEL SUB ASSY (for WHITE)71 2-582-132-01 PANEL (for SILVER)72 2-582-150-01 SHEET (LCD WINDOW), ADHESIVE

(for SILVER)73 2-178-844-01 WASHER (CD CHASSIS)

IC401 6-701-681-01 IC RPM7140-V4LCD401 1-479-194-11 ELEMENT UNIT, LIQUID CRYSTALSP101 1-826-212-11 SPEAKER (10cm) (L-ch)SP201 1-826-212-11 SPEAKER (10cm) (R-ch)

35

ZS-SN10

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark

6-3. CABINET TOP SECTION-1

notsupplied

cabinet top section-2

103

101

103

102103

104

111

110105

106

107

108

109

112

113

113116

116

114

115

101 2-582-129-01 HANDLE (R), HOLDER (BLACK)101 2-582-129-11 HANDLE (R), HOLDER (WHITE)101 2-582-129-21 HANDLE (R), HOLDER (SILVER)102 3-047-468-11 DAMPER103 3-252-827-01 SCREW (B2.6), (+) BV TAPPING

104 2-582-128-01 HANDLE (L), HOLDER (BLACK)104 2-582-128-11 HANDLE (L), HOLDER (WHITE)104 2-582-128-21 HANDLE (L), HOLDER (SILVER)105 1-452-899-11 MAGNET106 2-582-110-11 LID, CD (SILVER)

106 2-582-110-21 LID, CD (BLACK)106 2-582-110-31 LID, CD (WHITE)107 3-254-151-01 SCREW (B2.6), (+) P TAPPING108 2-591-496-01 COVER (HANDLE) (BLACK)108 2-591-496-11 COVER (HANDLE) (WHITE)

108 2-591-496-21 COVER (HANDLE) (SILVER)109 2-582-113-01 HANDLE (BLACK)109 2-582-113-11 HANDLE (WHITE)109 2-582-113-21 HANDLE (SILVER)110 3-019-395-01 PLATE, CHUCKING

111 3-253-143-01 SCREW (B2.6), (+) P TAPPING112 2-582-142-02 SPRING (CD)113 2-592-833-01 CUSHION114 2-634-609-01 COVER (SCREW) (for BLACK)114 2-634-609-11 COVER (SCREW) (for WHITE)

114 2-634-609-21 COVER (SCREW) (for SILVER)115 4-942-511-01 SPACER116 4-942-511-01 SPACER (BLACK)116 4-942-511-11 SPACER (WHITE, SILVER)

36

ZS-SN10

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark

6-4. CABINET TOP SECTION-2

151

152

167

153

151

154

155156

157

158

159160

158

159

163

162

161

157

optical pick-up section

S801

not supplied

S201

168

168

164

165

166

Ver. 1.4

151 3-252-827-01 SCREW (B2.6), (+) BV TAPP152 A-1105-376-A CONTROL (2) BOARD, COMPLETE153 A-1105-375-A CONTROL (1) BOARD, COMPLETE154 2-582-134-01 HOLDER (LED)155 X-2050-819-1 CABINET TOP SUB ASSY (BLACK) (US)

155 X-2050-820-1 CABINET TOP SUB ASSY (WHITE) (US)155 X-2050-821-1 CABINET TOP SUB ASSY (BLACK) (CND)155 X-2050-822-1 CABINET TOP SUB ASSY (WHITE) (CND)155 X-2050-823-1 CABINET TOP SUB ASSY (SILVER)

(EXCEPT US)155 X-2109-392-1 CABINET (UPPER) SUB ASSY (SILVER) (US)

156 3-923-736-01 COVER, CD157 3-931-379-21 RUBBER, VIBRATION PROOF (RED)158 3-931-379-31 RUBBER, VIBRATION PROOF (GREEN)

159 3-252-828-01 SCREW (B2.6), (+) PWH TAPPING160 1-828-377-51 WIRE (FLAT TYPE) (23 CORE)

161 A-1107-453-A CD BOARD, COMPLETE162 3-245-709-51 SCREW163 1-832-404-21 WIRE (FLAT TYPE) (16 CORE)164 3-015-345-21 CUSHION165 3-255-320-01 CUSHION, CR

166 3-018-963-01 CUSHION (BATTERY CASE LID)167 3-357-572-01 CUSHION168 3-885-228-01 CUSHION (B)S201 1-771-853-11 SWITCH, DETECTION (LIMIT)S801 1-692-960-21 SWITCH, PUSH (1 KEY)

(CD LID OPEN/CLOSE DETECT)

37

ZS-SN10

206

207

205

204203 202

202

214 214

201

211212

notsupplied

notsupplied

notsupplied

notsupplied

notsupplied

TUNER boardL3F902

J901

T901

213

213

210

208

209

214

216

215

215

215

* 201 1-866-326-11 BATTERY2 BOARD202 3-240-561-02 TERMINAL (–), BATTERY

* 203 1-866-325-11 BATTERY1 BOARD204 A-1105-328-A H/P BOARD, COMPLETE205 3-252-827-01 SCREW (B2.6), (+) BV TAPPING

206 3-254-143-01 SCREW (B3), (+) BV TAPPING207 A-1105-360-A POWER BOARD, COMPLETE208 1-827-720-51 WIRE (FLAT TYPE) (11 CORE)209 A-1105-354-A TUNER BOARD, COMPLETE (US, CND, E, MX)209 A-1105-355-A TUNER BOARD, COMPLETE

(SP, TW, KR, TH, AUS)

210 2-582-141-01 TERMINAL, ANTENNA211 2-582-153-01 SHEET, BATTERY212 2-582-109-02 CABINET (BOTTOM) (BLACK) (US)212 2-582-109-12 CABINET (BOTTOM) (WHITE) (US)212 2-582-109-22 CABINET (BOTTOM) (BLACK) (CND)

212 2-582-109-32 CABINET (BOTTOM) (WHITE) (CND)212 2-582-109-42 CABINET (BOTTOM) (SILVER)

(EXCEPT US, CND)

212 2-582-109-62 CABINET (BOTTOM) (SILVER) (US)212 2-582-109-72 CABINET (BOTTOM) (SILVER) (CND)213 3-252-830-01 SCREW (B3), (+) PWH TAPPING

214 3-018-963-01 CUSHION (BATTERY CASE LID)215 3-357-572-01 CUSHION216 4-942-511-01 SPACER (for BLACK)216 4-942-511-11 SPACER (for WHITE, SILVER)

0F902 1-533-450-12 FUSE, GLASS TUBE (DIA. 5) (2.5A/125V)(US, CND, E, MX, TW)

0F902 1-533-468-12 FUSE, GLASS TUBE (DIA. 5) (T2AL/250V)(SP, KR, TH, AUS)

0J901 1-526-818-11 INLET, AC (E, MX)0J901 1-526-838-11 INLET, AC 2P (SP, TW, KR, TH, AUS)0J901 1-540-009-11 INLET, AC (US, CND)

L3 1-754-117-12 ANTENNA, FERRITE-ROD (MW)

0T901 1-435-917-22 TRANSFORMER, POWER (US, CND, E, MX, TW)0T901 1-435-918-22 TRANSFORMER, POWER (SP, KR, TH, AUS)

6-5. CABINET BOTTOM SECTION

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark

Ver. 1.4

38

ZS-SN10

6-6. OPTICAL PICK-UP SECTION (KSM-213CDP)

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark

not supplied

M402

not supplied(M401 (SPINDLE))

503

501

502

506

504

505

0501 8-848-483-12 OPTICAL PICK-UP (KSS-213C/C2RP1)502 2-174-500-01 SCREW (2X3)503 2-626-908-01 SHAFT, SLED504 2-627-003-01 GEAR (B) (RP)505 X-2162-709-2 CHASSIS ASSY (CDP), MOTOR

(including M401 (SPINDLE))

506 2-626-907-11 GEAR (A)M402 X-2625-769-1 GEAR ASSY (MB) (RP), MOTOR (SLED)

39

ZS-SN10SECTION 7

ELECTRICAL PARTS LIST

NOTE:• Due to standardization, replacements in the

parts list may be different from the partsspecified in the diagrams or the componentsused on the set.

• -XX and -X mean standardized parts, so theymay have some difference from the originalone.

• Items marked “*” are not stocked since theyare seldom required for routine service.Some delay should be anticipated whenordering these items.

• CAPACITORSuF: µF

• COILSuH: µH

• RESISTORSAll resistors are in ohms.METAL: Metal-film resistor.METAL OXIDE: Metal oxide-film resistor.F: nonflammable

• SEMICONDUCTORSIn each case, u: µ, for example:uA. . : µA. ., uPA. . : µPA. .,uPB. . : µPB. ., uPC. . : µPC. .,uPD. . : µPD. .

• AbbreviationAUS : Australian model.CND : Canadian model.KR : Korean model.MX : Mexican model.

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark

When indicating parts by reference number,please include the board name.

* 1-866-325-11 BATTERY1 BOARD***************

3-240-561-02 TERMINAL (–), BATTERY************************************************************

* 1-866-326-11 BATTERY2 BOARD***************

3-240-561-02 TERMINAL (–), BATTERY

< CONNECTOR >

CN904 1-815-550-11 PIN, CONNECTOR (PWB) 2P************************************************************

A-1107-453-A CD BOARD, COMPLETE*******************

< CAPACITOR >

C101 1-162-919-11 CERAMIC CHIP 22PF 5% 50VC102 1-162-919-11 CERAMIC CHIP 22PF 5% 50VC103 1-162-927-11 CERAMIC CHIP 100PF 5% 50VC104 1-164-230-11 CERAMIC CHIP 220PF 5% 50VC105 1-162-927-11 CERAMIC CHIP 100PF 5% 50V

C107 1-164-230-11 CERAMIC CHIP 220PF 5% 50VC108 1-164-230-11 CERAMIC CHIP 220PF 5% 50VC109 1-164-230-11 CERAMIC CHIP 220PF 5% 50VC110 1-164-230-11 CERAMIC CHIP 220PF 5% 50VC111 1-164-230-11 CERAMIC CHIP 220PF 5% 50V

C112 1-162-927-11 CERAMIC CHIP 100PF 5% 50VC113 1-162-927-11 CERAMIC CHIP 100PF 5% 50VC132 1-162-919-11 CERAMIC CHIP 22PF 5% 50VC133 1-162-927-11 CERAMIC CHIP 100PF 5% 50VC201 1-128-995-21 ELECT CHIP 100uF 20% 10V

C202 1-164-360-11 CERAMIC CHIP 0.1uF 16VC203 1-128-995-21 ELECT CHIP 100uF 20% 10VC204 1-162-927-11 CERAMIC CHIP 100PF 5% 50VC205 1-164-360-11 CERAMIC CHIP 0.1uF 16VC206 1-164-360-11 CERAMIC CHIP 0.1uF 16V

C207 1-128-995-21 ELECT CHIP 100uF 20% 10VC208 1-164-360-11 CERAMIC CHIP 0.1uF 16VC210 1-164-360-11 CERAMIC CHIP 0.1uF 16VC213 1-164-360-11 CERAMIC CHIP 0.1uF 16VC214 1-164-360-11 CERAMIC CHIP 0.1uF 16V

C215 1-164-360-11 CERAMIC CHIP 0.1uF 16VC217 1-164-360-11 CERAMIC CHIP 0.1uF 16V

C218 1-164-360-11 CERAMIC CHIP 0.1uF 16VC219 1-164-360-11 CERAMIC CHIP 0.1uF 16VC220 1-162-927-11 CERAMIC CHIP 100PF 5% 50V

C221 1-164-360-11 CERAMIC CHIP 0.1uF 16VC222 1-164-360-11 CERAMIC CHIP 0.1uF 16VC223 1-162-923-11 CERAMIC CHIP 47PF 5% 50VC224 1-164-360-11 CERAMIC CHIP 0.1uF 16VC226 1-165-908-11 CERAMIC CHIP 1uF 10% 10V

C227 1-165-908-11 CERAMIC CHIP 1uF 10% 10VC230 1-162-927-11 CERAMIC CHIP 100PF 5% 50VC232 1-164-360-11 CERAMIC CHIP 0.1uF 16VC251 1-164-315-11 CERAMIC CHIP 470PF 5% 50VC252 1-162-968-11 CERAMIC CHIP 0.0047uF 10% 50V

C253 1-164-315-11 CERAMIC CHIP 470PF 5% 50VC254 1-162-968-11 CERAMIC CHIP 0.0047uF 10% 50VC256 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16VC257 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16VC258 1-164-230-11 CERAMIC CHIP 220PF 5% 50V

C259 1-162-927-11 CERAMIC CHIP 100PF 5% 50VC260 1-117-863-11 CERAMIC CHIP 0.47uF 10% 6.3VC261 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25VC264 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50VC265 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V

C267 1-162-919-11 CERAMIC CHIP 22PF 5% 50VC268 1-162-919-11 CERAMIC CHIP 22PF 5% 50VC269 1-126-208-21 ELECT CHIP 47uF 20% 4VC270 1-126-208-21 ELECT CHIP 47uF 20% 4VC271 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V

C272 1-164-360-11 CERAMIC CHIP 0.1uF 16VC273 1-164-315-11 CERAMIC CHIP 470PF 5% 50VC275 1-162-910-11 CERAMIC CHIP 5PF 0.25PF 50VC291 1-164-315-11 CERAMIC CHIP 470PF 5% 50VC292 1-164-315-11 CERAMIC CHIP 470PF 5% 50V

C301 1-164-360-11 CERAMIC CHIP 0.1uF 16VC302 1-137-710-11 CERAMIC CHIP 10uF 20% 6.3VC303 1-137-710-11 CERAMIC CHIP 10uF 20% 6.3VC321 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50VC322 1-115-156-11 CERAMIC CHIP 1uF 10V

C323 1-128-995-21 ELECT CHIP 100uF 20% 10VC401 1-128-396-11 ELECT CHIP 470uF 20% 10VC404 1-164-360-11 CERAMIC CHIP 0.1uF 16VC405 1-164-360-11 CERAMIC CHIP 0.1uF 16VC406 1-164-360-11 CERAMIC CHIP 0.1uF 16V

C424 1-164-360-11 CERAMIC CHIP 0.1uF 16V

BATTERY1

SP : Singapore model.TH : Thai model.TW : Taiwan model.

BATTERY2 CD

The components identified by mark 0 ordotted line with mark 0 are critical for safety.Replace only with part number specified.

Les composants identifiés par une marque 0sont critiques pour la sécurité.Ne les remplacer que par une pièce portant lenuméro spécifié.

Ver. 1.1

40

ZS-SN10

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark

C451 1-165-176-11 CERAMIC CHIP 0.047uF 10% 16V

< CONNECTOR >

CN102 1-770-706-21 CONNECTOR, FFC/FPC 23PCN301 1-770-425-51 CONNECTOR, FFC/FPC 16P

< IC >

IC201 8-753-239-32 IC CXD3014-201RIC202 6-708-165-01 IC TK73325WTL-GIC402 6-708-516-01 IC FAN8040G3

< TRANSISTOR >

Q321 6-551-120-01 TRANSISTOR 2SA2119K

< RESISTOR >

R101 1-216-809-11 METAL CHIP 100 5% 1/10WR102 1-216-809-11 METAL CHIP 100 5% 1/10WR103 1-216-809-11 METAL CHIP 100 5% 1/10WR104 1-216-809-11 METAL CHIP 100 5% 1/10WR105 1-216-809-11 METAL CHIP 100 5% 1/10W

R107 1-216-809-11 METAL CHIP 100 5% 1/10WR108 1-216-809-11 METAL CHIP 100 5% 1/10WR109 1-216-809-11 METAL CHIP 100 5% 1/10WR110 1-216-809-11 METAL CHIP 100 5% 1/10WR111 1-216-809-11 METAL CHIP 100 5% 1/10W

R112 1-216-809-11 METAL CHIP 100 5% 1/10WR113 1-216-809-11 METAL CHIP 100 5% 1/10WR115 1-216-864-11 SHORT CHIP 0R201 1-216-295-91 SHORT CHIP 0R202 1-216-295-91 SHORT CHIP 0

R203 1-216-295-91 SHORT CHIP 0R207 1-216-295-91 SHORT CHIP 0R249 1-216-841-11 METAL CHIP 47K 5% 1/10WR250 1-216-857-11 METAL CHIP 1M 5% 1/10WR252 1-216-833-11 METAL CHIP 10K 5% 1/10W

R253 1-216-821-11 METAL CHIP 1K 5% 1/10WR254 1-216-833-11 METAL CHIP 10K 5% 1/10WR255 1-216-821-11 METAL CHIP 1K 5% 1/10WR256 1-216-837-11 METAL CHIP 22K 5% 1/10WR257 1-216-853-11 METAL CHIP 470K 5% 1/10W

R258 1-216-849-11 METAL CHIP 220K 5% 1/10WR259 1-216-833-11 METAL CHIP 10K 5% 1/10WR260 1-216-864-11 SHORT CHIP 0R265 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR266 1-216-821-11 METAL CHIP 1K 5% 1/10W

R267 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR268 1-216-833-11 METAL CHIP 10K 5% 1/10WR270 1-216-817-11 METAL CHIP 470 5% 1/10WR271 1-216-857-11 METAL CHIP 1M 5% 1/10WR275 1-216-809-11 METAL CHIP 100 5% 1/10W

R276 1-216-841-11 METAL CHIP 47K 5% 1/10WR277 1-216-809-11 METAL CHIP 100 5% 1/10WR278 1-216-809-11 METAL CHIP 100 5% 1/10WR280 1-216-864-11 SHORT CHIP 0R291 1-216-809-11 METAL CHIP 100 5% 1/10W

R292 1-216-809-11 METAL CHIP 100 5% 1/10WR321 1-216-789-11 METAL CHIP 2.2 5% 1/10W

R322 1-216-789-11 METAL CHIP 2.2 5% 1/10WR323 1-216-864-11 SHORT CHIP 0R324 1-216-845-11 METAL CHIP 100K 5% 1/10W

R325 1-216-864-11 SHORT CHIP 0R326 1-216-864-11 SHORT CHIP 0R401 1-216-295-91 SHORT CHIP 0R421 1-216-864-11 SHORT CHIP 0R423 1-216-833-11 METAL CHIP 10K 5% 1/10W

R451 1-216-837-11 METAL CHIP 22K 5% 1/10WR452 1-216-833-11 METAL CHIP 10K 5% 1/10W

< VIBRATOR >

X202 1-767-408-21 VIBRATOR, CRYSTAL (16.9344MHz)************************************************************

A-1105-375-A CONTROL (1) BOARD, COMPLETE***************************

< CONNECTOR >

CN401 1-815-550-11 PIN, CONNECTOR (PWB) 2PCN403 1-784-726-11 CONNECTOR, FFC 4P

< LED >

D401 8-719-059-97 LED L-34HD (OPR/BATT)

< RESISTOR >

R418 1-216-817-11 METAL CHIP 470 5% 1/10WR419 1-216-817-11 METAL CHIP 470 5% 1/10WR420 1-216-821-11 METAL CHIP 1K 5% 1/10WR421 1-216-821-11 METAL CHIP 1K 5% 1/10WR425 1-216-813-11 METAL CHIP 220 5% 1/10W

R426 1-216-813-11 METAL CHIP 220 5% 1/10WR427 1-216-817-11 METAL CHIP 470 5% 1/10W

< SWITCH >

S402 1-786-050-21 SWITCH, KEY BOARD (POWER)S403 1-786-050-21 SWITCH, KEY BOARD (SLEEP)

************************************************************

A-1105-376-A CONTROL (2) BOARD, COMPLETE***************************

< RESISTOR >

R428 1-216-821-11 METAL CHIP 1K 5% 1/10WR429 1-216-821-11 METAL CHIP 1K 5% 1/10WR430 1-216-825-11 METAL CHIP 2.2K 5% 1/10WR431 1-216-821-11 METAL CHIP 1K 5% 1/10WR432 1-216-825-11 METAL CHIP 2.2K 5% 1/10W

< SWITCH >

S404 1-786-050-21 SWITCH, KEY BOARD (VOLUME +)S405 1-786-050-21 SWITCH, KEY BOARD (VOLUME –)S406 1-786-050-21 SWITCH, KEY BOARD (MEGA BASS)S407 1-786-050-21 SWITCH, KEY BOARD (SOUND)

************************************************************

CD CONTROL (1) CONTROL (2)Ver. 1.3

41

ZS-SN10

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark

A-1105-328-A H/P BOARD, COMPLETE*******************

< CAPACITOR >

C119 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50VC219 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V

< CONNECTOR >

* CN323 1-815-552-11 PIN, CONNECTOR (PWB) 4P

< FERRITE BEAD >

FB101 1-469-701-21 FERRITE, EMI (SMD) (1608)FB201 1-469-701-21 FERRITE, EMI (SMD) (1608)FB301 1-469-701-21 FERRITE, EMI (SMD) (1608)

< JACK >

J301 1-815-325-11 JACK (i)J322 1-566-891-11 JACK (LINE IN)

< COIL >

L101 1-410-517-11 INDUCTOR 47uHL201 1-410-517-11 INDUCTOR 47uHL301 1-414-142-61 INDUCTOR 1uH

< RESISTOR >

R126 1-216-809-11 METAL CHIP 100 5% 1/10WR226 1-216-809-11 METAL CHIP 100 5% 1/10W

************************************************************

A-1105-337-A LCD BOARD, COMPLETE (for BLACK, SILVER)A-1124-479-A LCD BOARD, COMPLETE (for WHITE)

********************

2-582-131-01 HOLDER, LCD2-582-138-01 PLATE, LIGHT GUIDE2-582-152-01 ILLUMINATOR

< CAPACITOR >

C401 1-115-156-11 CERAMIC CHIP 1uF 10VC402 1-115-156-11 CERAMIC CHIP 1uF 10VC403 1-115-156-11 CERAMIC CHIP 1uF 10VC404 1-115-156-11 CERAMIC CHIP 1uF 10VC405 1-162-962-11 CERAMIC CHIP 470PF 10% 50V

C406 1-162-974-11 CERAMIC CHIP 0.01uF 50VC407 1-162-923-11 CERAMIC CHIP 47PF 5% 50VC408 1-162-923-11 CERAMIC CHIP 47PF 5% 50VC409 1-162-923-11 CERAMIC CHIP 47PF 5% 50VC410 1-162-923-11 CERAMIC CHIP 47PF 5% 50V

C411 1-162-923-11 CERAMIC CHIP 47PF 5% 50VC412 1-162-923-11 CERAMIC CHIP 47PF 5% 50VC413 1-162-923-11 CERAMIC CHIP 47PF 5% 50VC414 1-162-923-11 CERAMIC CHIP 47PF 5% 50VC417 1-162-923-11 CERAMIC CHIP 47PF 5% 50V

C418 1-162-923-11 CERAMIC CHIP 47PF 5% 50VC419 1-162-974-11 CERAMIC CHIP 0.01uF 50VC420 1-162-974-11 CERAMIC CHIP 0.01uF 50V

< CONNECTOR >

CN402 1-770-519-31 CONNECTOR, FFC/FPC 11PCN405 1-770-519-31 CONNECTOR, FFC/FPC 11P

< LED >

D402 6-501-437-01 LED SLI-343YC3F (LCD BACK LIGHT)(EXCEPT US (WHITE), CND (WHITE))

D402 6-500-863-01 LED SLR343EBT (LCD BACK LIGHT)(US (WHITE), CND (WHITE))

< IC >

IC401 6-701-681-01 IC RPM7140-V4

< COIL >

L401 1-410-517-11 INDUCTOR 47uHL402 1-414-142-61 INDUCTOR 1uHL403 1-414-142-61 INDUCTOR 1uH

< LIQUID CRYSTAL DISPLAY >

LCD401 1-479-194-11 ELEMENT UNIT, LIQUID CRYSTAL I

< RESISTOR >

R401 1-216-821-11 METAL CHIP 1K 5% 1/10WR402 1-216-821-11 METAL CHIP 1K 5% 1/10WR415 1-216-841-11 METAL CHIP 47K 5% 1/10WR416 1-216-845-11 METAL CHIP 100K 5% 1/10WR417 1-216-853-11 METAL CHIP 470K 5% 1/10W

R436 1-216-813-11 METAL CHIP 220 5% 1/10WR437 1-216-817-11 METAL CHIP 470 5% 1/10WR438 1-216-821-11 METAL CHIP 1K 5% 1/10WR439 1-216-821-11 METAL CHIP 1K 5% 1/10WR440 1-216-825-11 METAL CHIP 2.2K 5% 1/10W

R446 1-216-813-11 METAL CHIP 220 5% 1/10WR447 1-216-817-11 METAL CHIP 470 5% 1/10WR448 1-216-821-11 METAL CHIP 1K 5% 1/10WR449 1-216-821-11 METAL CHIP 1K 5% 1/10WR450 1-216-825-11 METAL CHIP 2.2K 5% 1/10W

R451 1-216-825-11 METAL CHIP 2.2K 5% 1/10WR452 1-216-821-11 METAL CHIP 1K 5% 1/10WR453 1-216-825-11 METAL CHIP 2.2K 5% 1/10WR454 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR458 1-216-817-11 METAL CHIP 470 5% 1/10W

R459 1-216-813-11 METAL CHIP 220 5% 1/10W(US (WHITE), CND (WHITE))

R459 1-216-817-11 METAL CHIP 470 5% 1/10W(EXCEPT US (WHITE), CND (WHITE))

R490 1-216-825-11 METAL CHIP 2.2K 5% 1/10WR491 1-216-864-11 SHORT CHIP 0R492 1-216-833-11 METAL CHIP 10K 5% 1/10W

R493 1-216-821-11 METAL CHIP 1K 5% 1/10WR494 1-216-825-11 METAL CHIP 2.2K 5% 1/10W

< SWITCH >

S401 1-478-528-11 ENCODER (ROTARY) (JOG)S410 1-786-050-21 SWITCH, KEY BOARD (LINE)S411 1-786-050-21 SWITCH, KEY BOARD

(RADIO/BAND, AUTO PRESET)

H/P LCDVer. 1.3

42

ZS-SN10

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark

S412 1-786-050-21 SWITCH, KEY BOARD (FOLDER/TUNE –)S413 1-786-050-21 SWITCH, KEY BOARD (FOLDER/TUNE +)

S414 1-786-050-21 SWITCH, KEY BOARD (ENTER/MEMORY)S418 1-786-050-21 SWITCH, KEY BOARD (u)S419 1-786-050-21 SWITCH, KEY BOARD (x)S420 1-786-050-21 SWITCH, KEY BOARD (> PRESET +)S421 1-786-050-21 SWITCH, KEY BOARD (. PRESET –)

S422 1-786-050-21 SWITCH, KEY BOARD (REPEAT)S423 1-786-050-21 SWITCH, KEY BOARD (MODE)S424 1-786-050-21 SWITCH, KEY BOARD (DISPLAY)S425 1-786-050-21 SWITCH, KEY BOARD (FOLDER SEARCH)

************************************************************

A-1105-346-A MAIN BOARD, COMPLETE (US, CND, E, MX)A-1105-348-A MAIN BOARD, COMPLETE (SP, TH)A-1105-349-A MAIN BOARD, COMPLETE (TW, KR, AUS)

*********************

2-594-013-01 PLATE (MAIN), SHIELD3-253-143-01 SCREW (B2.6), (+) P TAPPING

< CAPACITOR >

C101 1-126-961-11 ELECT 2.2uF 20% 50VC102 1-126-961-11 ELECT 2.2uF 20% 50VC103 1-126-959-11 ELECT 0.47uF 20% 50VC104 1-126-963-11 ELECT 4.7uF 20% 50VC105 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V

C106 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50VC107 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50VC108 1-162-966-11 CERAMIC CHIP 0.0022uF 10% 50VC109 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16VC110 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V

C111 1-126-963-11 ELECT 4.7uF 20% 50VC112 1-162-968-11 CERAMIC CHIP 0.0047uF 10% 50VC113 1-162-966-11 CERAMIC CHIP 0.0022uF 10% 50VC114 1-126-960-11 ELECT 1uF 20% 50VC116 1-162-966-11 CERAMIC CHIP 0.0022uF 10% 50V

C117 1-126-960-11 ELECT 1uF 20% 50VC118 1-126-960-11 ELECT 1uF 20% 50VC120 1-162-927-11 CERAMIC CHIP 100PF 5% 50VC122 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50VC123 1-126-785-11 ELECT 47uF 20% 10V

(US, CND, E, MX)

C123 1-126-947-11 ELECT 47uF 20% 35V(SP, TW, KR, TH, AUS)

C124 1-104-658-91 ELECT 100uF 20% 10VC125 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16VC126 1-126-926-11 ELECT 1000uF 20% 10VC127 1-162-927-11 CERAMIC CHIP 100PF 5% 50V

C201 1-126-961-11 ELECT 2.2uF 20% 50VC202 1-126-961-11 ELECT 2.2uF 20% 50VC203 1-126-959-11 ELECT 0.47uF 20% 50VC204 1-126-963-11 ELECT 4.7uF 20% 50VC205 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V

C206 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50VC207 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50VC208 1-162-966-11 CERAMIC CHIP 0.0022uF 10% 50VC209 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16VC210 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V

C211 1-126-963-11 ELECT 4.7uF 20% 50VC212 1-162-968-11 CERAMIC CHIP 0.0047uF 10% 50VC213 1-162-966-11 CERAMIC CHIP 0.0022uF 10% 50VC214 1-126-960-11 ELECT 1uF 20% 50VC216 1-162-966-11 CERAMIC CHIP 0.0022uF 10% 50V

C217 1-126-960-11 ELECT 1uF 20% 50VC218 1-126-960-11 ELECT 1uF 20% 50VC220 1-162-927-11 CERAMIC CHIP 100PF 5% 50VC222 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50VC223 1-126-785-11 ELECT 47uF 20% 10V

(US, CND, E, MX)

C223 1-126-947-11 ELECT 47uF 20% 35V(SP, TW, KR, TH, AUS)

C224 1-104-658-91 ELECT 100uF 20% 10VC225 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16VC226 1-126-926-11 ELECT 1000uF 20% 10VC227 1-162-927-11 CERAMIC CHIP 100PF 5% 50V

C301 1-104-658-91 ELECT 100uF 20% 10VC302 1-162-974-11 CERAMIC CHIP 0.01uF 50VC303 1-126-959-11 ELECT 0.47uF 20% 50VC304 1-126-947-11 ELECT 47uF 20% 35VC305 1-162-927-11 CERAMIC CHIP 100PF 5% 50V

C306 1-162-927-11 CERAMIC CHIP 100PF 5% 50VC321 1-104-662-91 ELECT 22uF 20% 25VC322 1-126-947-11 ELECT 47uF 20% 35VC324 1-115-467-11 CERAMIC CHIP 0.22uF 10% 10VC325 1-126-964-11 ELECT 10uF 20% 50V

C326 1-126-934-11 ELECT 220uF 20% 16VC421 1-162-927-11 CERAMIC CHIP 100PF 5% 50VC422 1-162-927-11 CERAMIC CHIP 100PF 5% 50VC423 1-162-962-11 CERAMIC CHIP 470PF 10% 50VC424 1-162-962-11 CERAMIC CHIP 470PF 10% 50V

C425 1-162-962-11 CERAMIC CHIP 470PF 10% 50VC426 1-162-962-11 CERAMIC CHIP 470PF 10% 50VC427 1-162-962-11 CERAMIC CHIP 470PF 10% 50VC428 1-162-962-11 CERAMIC CHIP 470PF 10% 50VC429 1-162-962-11 CERAMIC CHIP 470PF 10% 50V

C430 1-162-962-11 CERAMIC CHIP 470PF 10% 50VC431 1-162-962-11 CERAMIC CHIP 470PF 10% 50VC432 1-162-962-11 CERAMIC CHIP 470PF 10% 50VC433 1-162-927-11 CERAMIC CHIP 100PF 5% 50VC434 1-162-962-11 CERAMIC CHIP 470PF 10% 50V

C801 1-164-156-11 CERAMIC CHIP 0.1uF 25VC802 1-162-974-11 CERAMIC CHIP 0.01uF 50VC803 1-126-513-11 ELECT 47uF 20% 6.3V

(US, CND, E, MX)C803 1-126-947-11 ELECT 47uF 20% 35V

(SP, TW, KR, TH, AUS)C805 1-162-927-11 CERAMIC CHIP 100PF 5% 50V

C806 1-164-156-11 CERAMIC CHIP 0.1uF 25VC807 1-162-927-11 CERAMIC CHIP 100PF 5% 50VC808 1-162-927-11 CERAMIC CHIP 100PF 5% 50VC809 1-162-927-11 CERAMIC CHIP 100PF 5% 50VC810 1-162-927-11 CERAMIC CHIP 100PF 5% 50V

C811 1-162-927-11 CERAMIC CHIP 100PF 5% 50VC812 1-162-927-11 CERAMIC CHIP 100PF 5% 50VC813 1-162-927-11 CERAMIC CHIP 100PF 5% 50V-C814 1-162-927-11 CERAMIC CHIP 100PF 5% 50VC815 1-162-927-11 CERAMIC CHIP 100PF 5% 50V

MAINLCDVer. 1.3

43

ZS-SN10

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark

C816 1-162-919-11 CERAMIC CHIP 22PF 5% 50VC817 1-162-919-11 CERAMIC CHIP 22PF 5% 50VC818 1-162-927-11 CERAMIC CHIP 100PF 5% 50V

C819 1-162-927-11 CERAMIC CHIP 100PF 5% 50VC820 1-162-974-11 CERAMIC CHIP 0.01uF 50VC821 1-162-974-11 CERAMIC CHIP 0.01uF 50VC822 1-162-974-11 CERAMIC CHIP 0.01uF 50VC823 1-162-919-11 CERAMIC CHIP 22PF 5% 50V

C824 1-162-915-11 CERAMIC CHIP 10PF 0.5PF 50VC825 1-164-230-11 CERAMIC CHIP 220PF 5% 50VC826 1-162-923-11 CERAMIC CHIP 47PF 5% 50VC827 1-164-230-11 CERAMIC CHIP 220PF 5% 50VC828 1-162-923-11 CERAMIC CHIP 47PF 5% 50V

C829 1-162-919-11 CERAMIC CHIP 22PF 5% 50VC830 1-162-915-11 CERAMIC CHIP 10PF 0.5PF 50VC831 1-115-156-11 CERAMIC CHIP 1uF 10VC832 1-162-927-11 CERAMIC CHIP 100PF 5% 50VC833 1-162-927-11 CERAMIC CHIP 100PF 5% 50V

C837 1-162-974-11 CERAMIC CHIP 0.01uF 50VC838 1-162-974-11 CERAMIC CHIP 0.01uF 50VC839 1-162-974-11 CERAMIC CHIP 0.01uF 50VC840 1-162-974-11 CERAMIC CHIP 0.01uF 50VC841 1-162-974-11 CERAMIC CHIP 0.01uF 50V

C842 1-162-927-11 CERAMIC CHIP 100PF 5% 50VC845 1-162-923-11 CERAMIC CHIP 47PF 5% 50VC848 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25VC849 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50VC850 1-162-962-11 CERAMIC CHIP 470PF 10% 50V

C851 1-162-927-11 CERAMIC CHIP 100PF 5% 50VC852 1-162-927-11 CERAMIC CHIP 100PF 5% 50VC853 1-162-927-11 CERAMIC CHIP 100PF 5% 50VC854 1-162-927-11 CERAMIC CHIP 100PF 5% 50VC855 1-115-156-11 CERAMIC CHIP 1uF 10V

C856 1-115-156-11 CERAMIC CHIP 1uF 10VC859 1-162-919-11 CERAMIC CHIP 22PF 5% 50VC860 1-162-919-11 CERAMIC CHIP 22PF 5% 50VC861 1-162-927-11 CERAMIC CHIP 100PF 5% 50VC862 1-162-927-11 CERAMIC CHIP 100PF 5% 50V

C867 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50VC868 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25VC869 1-115-156-11 CERAMIC CHIP 1uF 10VC870 1-126-964-11 ELECT 10uF 20% 50VC871 1-162-919-11 CERAMIC CHIP 22PF 5% 50V

C872 1-162-919-11 CERAMIC CHIP 22PF 5% 50VC873 1-126-926-11 ELECT 1000uF 20% 10VC874 1-126-923-91 ELECT 220uF 20% 10VC875 1-164-230-11 CERAMIC CHIP 220PF 5% 50VC907 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V

C950 1-126-937-11 ELECT 4700uF 20% 16VC951 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25VC952 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25VC953 1-126-923-91 ELECT 220uF 20% 10VC954 1-104-658-91 ELECT 100uF 20% 10V

C955 1-126-923-91 ELECT 220uF 20% 10VC956 1-104-658-91 ELECT 100uF 20% 10VC957 1-164-156-11 CERAMIC CHIP 0.1uF 25VC958 1-164-156-11 CERAMIC CHIP 0.1uF 25VC959 1-126-934-11 ELECT 220uF 20% 16V

C960 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25VC961 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25VC963 1-126-964-11 ELECT 10uF 20% 50V

< CONNECTOR >

CN301 1-815-445-11 PIN, CONNECTOR (PWB) 4PCN302 1-815-444-11 PIN, CONNECTOR (PWB) 3PCN801 1-779-291-11 CONNECTOR, FFC (LIF (NON-ZIF)) 23PCN802 1-568-830-11 CONNECTOR 11PCN804 1-784-765-11 CONNECTOR, FFC 4P

CN806 1-568-830-11 CONNECTOR 11PCN807 1-568-830-11 CONNECTOR 11PCN901 1-815-445-21 PIN, CONNECTOR (PWB) 4P

< DIODE >

D301 8-719-082-07 DIODE KDS121-RTKD801 8-719-082-07 DIODE KDS121-RTKD802 8-719-069-54 DIODE UDZSTE-175.1BD905 8-719-978-33 DIODE DTZ-TT11-6.8BD906 8-719-988-61 DIODE 1SS355TE-17

D907 8-719-988-61 DIODE 1SS355TE-17D908 8-719-988-61 DIODE 1SS355TE-17D951 8-719-083-93 DIODE KDS120-RTKD953 8-719-978-33 DIODE DTZ-TT11-6.8B

< FERRITE BEAD >

FB801 1-469-701-21 FERRITE, EMI (SMD) (1608)FB802 1-469-701-21 FERRITE, EMI (SMD) (1608)FB803 1-500-445-21 FERRITE, EMI (SMD) (2012)FB804 1-500-445-21 FERRITE, EMI (SMD) (2012)

< IC >

IC301 6-701-824-11 IC BD3870FS-E2IC304 8-759-426-51 IC BA5417IC801 6-806-037-01 IC MB90483BPF-G-153E1IC802 6-706-338-01 IC XC6202P332FRIC803 6-703-224-01 IC S-80828CNNB-B8NT2G

IC804 6-704-004-01 IC BR24L16F-WE2IC901 8-759-679-43 IC S-816A33AMC-BAI-T2-G

< JUMPER RESISTOR >

JC801 1-216-864-11 SHORT CHIP 0JC802 1-216-864-11 SHORT CHIP 0JC803 1-216-864-11 SHORT CHIP 0JC804 1-216-864-11 SHORT CHIP 0JC805 1-216-864-11 SHORT CHIP 0

JC806 1-216-864-11 SHORT CHIP 0JC807 1-216-864-11 SHORT CHIP 0JC808 1-216-864-11 SHORT CHIP 0

< COIL >

L801 1-410-509-11 INDUCTOR 10uHL802 1-414-137-31 INDUCTOR 0.22uHL803 1-414-142-61 INDUCTOR 1uHL804 1-410-517-11 INDUCTOR 47uHL806 1-414-142-61 INDUCTOR 1uH

L807 1-410-517-11 INDUCTOR 47uH

MAINVer. 1.3

44

ZS-SN10

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark

< TRANSISTOR >

Q101 8-729-602-21 TRANSISTOR 2SC4154-FQ121 8-729-029-10 TRANSISTOR DTC143TUA-T106Q201 8-729-602-21 TRANSISTOR 2SC4154-FQ221 8-729-029-10 TRANSISTOR DTC143TUA-T106Q801 8-729-602-21 TRANSISTOR 2SC4154-F

Q802 8-729-602-21 TRANSISTOR 2SC4154-FQ803 8-729-602-21 TRANSISTOR 2SC4154-FQ804 8-729-028-76 TRANSISTOR DTA114YUA-T106Q805 8-729-028-99 TRANSISTOR DTC114YUA-T106Q806 8-729-028-99 TRANSISTOR DTC114YUA-T106

Q807 8-729-602-36 TRANSISTOR 2SA1602-FQ808 8-729-028-99 TRANSISTOR DTC114YUA-T106Q809 8-729-028-99 TRANSISTOR DTC114YUA-T106Q810 8-729-028-76 TRANSISTOR DTA114YUA-T106Q811 6-551-420-01 TRANSISTOR RT1N151M-TP-1

Q812 6-551-424-01 TRANSISTOR RT1P151M-TP-1Q813 8-729-602-36 TRANSISTOR 2SA1602-FQ821 6-551-424-01 TRANSISTOR RT1P151M-TP-1Q822 6-551-420-01 TRANSISTOR RT1N151M-TP-1Q823 8-729-602-21 TRANSISTOR 2SC4154-F

Q824 8-729-037-13 TRANSISTOR KTA1271YQ951 6-551-422-01 TRANSISTOR RT1N436M-TP-1Q952 8-729-040-76 TRANSISTOR KTA1273-Y-ATQ953 8-729-602-21 TRANSISTOR 2SC4154-FQ954 8-729-018-99 TRANSISTOR 2SD2394-F

Q955 8-729-036-86 TRANSISTOR KTC3203Y-ATQ956 8-729-101-07 TRANSISTOR 2SB798-DL

< RESISTOR >

R101 1-216-833-11 METAL CHIP 10K 5% 1/10WR102 1-216-825-11 METAL CHIP 2.2K 5% 1/10WR103 1-216-825-11 METAL CHIP 2.2K 5% 1/10WR104 1-216-821-11 METAL CHIP 1K 5% 1/10WR105 1-216-833-11 METAL CHIP 10K 5% 1/10W

R106 1-216-841-11 METAL CHIP 47K 5% 1/10WR110 1-216-833-11 METAL CHIP 10K 5% 1/10WR111 1-216-821-11 METAL CHIP 1K 5% 1/10WR112 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR113 1-216-853-11 METAL CHIP 470K 5% 1/10W

R114 1-216-825-11 METAL CHIP 2.2K 5% 1/10WR115 1-216-821-11 METAL CHIP 1K 5% 1/10WR116 1-216-813-11 METAL CHIP 220 5% 1/10WR117 1-216-817-11 METAL CHIP 470 5% 1/10WR118 1-216-864-11 SHORT CHIP 0

R119 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR120 1-216-841-11 METAL CHIP 47K 5% 1/10WR121 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR122 1-216-813-11 METAL CHIP 220 5% 1/10WR123 1-216-817-11 METAL CHIP 470 5% 1/10W

R124 1-216-789-11 METAL CHIP 2.2 5% 1/10WR125 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR127 1-216-864-11 SHORT CHIP 0R201 1-216-833-11 METAL CHIP 10K 5% 1/10WR202 1-216-825-11 METAL CHIP 2.2K 5% 1/10W

R203 1-216-825-11 METAL CHIP 2.2K 5% 1/10W

R204 1-216-821-11 METAL CHIP 1K 5% 1/10WR205 1-216-833-11 METAL CHIP 10K 5% 1/10WR206 1-216-841-11 METAL CHIP 47K 5% 1/10WR210 1-216-833-11 METAL CHIP 10K 5% 1/10W

R211 1-216-821-11 METAL CHIP 1K 5% 1/10WR212 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR213 1-216-853-11 METAL CHIP 470K 5% 1/10WR214 1-216-825-11 METAL CHIP 2.2K 5% 1/10WR215 1-216-821-11 METAL CHIP 1K 5% 1/10W

R216 1-216-813-11 METAL CHIP 220 5% 1/10WR217 1-216-817-11 METAL CHIP 470 5% 1/10WR218 1-216-864-11 SHORT CHIP 0R219 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR220 1-216-841-11 METAL CHIP 47K 5% 1/10W

R221 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR222 1-216-813-11 METAL CHIP 220 5% 1/10WR223 1-216-817-11 METAL CHIP 470 5% 1/10WR224 1-216-789-11 METAL CHIP 2.2 5% 1/10WR225 1-216-829-11 METAL CHIP 4.7K 5% 1/10W

R227 1-216-864-11 SHORT CHIP 0R301 1-216-809-11 METAL CHIP 100 5% 1/10WR302 1-216-809-11 METAL CHIP 100 5% 1/10WR303 1-216-833-11 METAL CHIP 10K 5% 1/10WR304 1-216-833-11 METAL CHIP 10K 5% 1/10W

R305 1-216-821-11 METAL CHIP 1K 5% 1/10WR306 1-216-821-11 METAL CHIP 1K 5% 1/10WR309 1-216-833-11 METAL CHIP 10K 5% 1/10WR321 1-216-825-11 METAL CHIP 2.2K 5% 1/10WR322 1-216-821-11 METAL CHIP 1K 5% 1/10W

R323 1-216-833-11 METAL CHIP 10K 5% 1/10WR324 1-216-857-11 METAL CHIP 1M 5% 1/10WR325 1-216-821-11 METAL CHIP 1K 5% 1/10WR326 1-216-821-11 METAL CHIP 1K 5% 1/10WR468 1-216-829-11 METAL CHIP 4.7K 5% 1/10W

R469 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR470 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR471 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR472 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR473 1-216-829-11 METAL CHIP 4.7K 5% 1/10W

R474 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR475 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR476 1-216-825-11 METAL CHIP 2.2K 5% 1/10WR477 1-216-825-11 METAL CHIP 2.2K 5% 1/10WR478 1-216-825-11 METAL CHIP 2.2K 5% 1/10W

R479 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR480 1-216-821-11 METAL CHIP 1K 5% 1/10WR481 1-216-821-11 METAL CHIP 1K 5% 1/10WR483 1-216-825-11 METAL CHIP 2.2K 5% 1/10WR484 1-216-825-11 METAL CHIP 2.2K 5% 1/10W

R485 1-216-825-11 METAL CHIP 2.2K 5% 1/10WR486 1-216-825-11 METAL CHIP 2.2K 5% 1/10WR488 1-216-833-11 METAL CHIP 10K 5% 1/10WR495 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR496 1-216-825-11 METAL CHIP 2.2K 5% 1/10W

R497 1-216-845-11 METAL CHIP 100K 5% 1/10WR498 1-216-797-11 METAL CHIP 10 5% 1/10WR499 1-216-813-11 METAL CHIP 220 5% 1/10W

MAINVer. 1.3

45

ZS-SN10

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark

R800 1-216-853-11 METAL CHIP 470K 5% 1/10WR801 1-216-833-11 METAL CHIP 10K 5% 1/10W

(TW, KR, AUS)

R802 1-216-833-11 METAL CHIP 10K 5% 1/10W(EXCEPT TW, KR, AUS)

R803 1-216-833-11 METAL CHIP 10K 5% 1/10WR805 1-216-833-11 METAL CHIP 10K 5% 1/10W

(SP, TW, KR, TH, AUS)R806 1-216-833-11 METAL CHIP 10K 5% 1/10W

(US, CND, E, MX)R807 1-216-817-11 METAL CHIP 470 5% 1/10W

R808 1-216-817-11 METAL CHIP 470 5% 1/10WR811 1-216-833-11 METAL CHIP 10K 5% 1/10WR812 1-216-849-11 METAL CHIP 220K 5% 1/10WR813 1-216-849-11 METAL CHIP 220K 5% 1/10WR815 1-216-829-11 METAL CHIP 4.7K 5% 1/10W

R816 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR817 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR818 1-216-837-11 METAL CHIP 22K 5% 1/10WR825 1-216-821-11 METAL CHIP 1K 5% 1/10WR826 1-216-821-11 METAL CHIP 1K 5% 1/10W

R827 1-216-821-11 METAL CHIP 1K 5% 1/10WR828 1-216-841-11 METAL CHIP 47K 5% 1/10WR829 1-216-821-11 METAL CHIP 1K 5% 1/10WR830 1-216-809-11 METAL CHIP 100 5% 1/10WR831 1-216-813-11 METAL CHIP 220 5% 1/10W

R832 1-216-809-11 METAL CHIP 100 5% 1/10WR833 1-216-821-11 METAL CHIP 1K 5% 1/10WR834 1-216-821-11 METAL CHIP 1K 5% 1/10WR835 1-216-821-11 METAL CHIP 1K 5% 1/10WR836 1-216-821-11 METAL CHIP 1K 5% 1/10W

R837 1-216-821-11 METAL CHIP 1K 5% 1/10WR838 1-216-821-11 METAL CHIP 1K 5% 1/10WR839 1-216-821-11 METAL CHIP 1K 5% 1/10WR840 1-216-825-11 METAL CHIP 2.2K 5% 1/10WR841 1-216-821-11 METAL CHIP 1K 5% 1/10W

R842 1-216-821-11 METAL CHIP 1K 5% 1/10WR844 1-216-837-11 METAL CHIP 22K 5% 1/10WR845 1-216-841-11 METAL CHIP 47K 5% 1/10WR846 1-216-833-11 METAL CHIP 10K 5% 1/10WR847 1-216-821-11 METAL CHIP 1K 5% 1/10W

R848 1-216-821-11 METAL CHIP 1K 5% 1/10WR849 1-216-821-11 METAL CHIP 1K 5% 1/10WR850 1-216-821-11 METAL CHIP 1K 5% 1/10WR851 1-216-821-11 METAL CHIP 1K 5% 1/10WR852 1-216-841-11 METAL CHIP 47K 5% 1/10W

R853 1-216-833-11 METAL CHIP 10K 5% 1/10WR854 1-216-833-11 METAL CHIP 10K 5% 1/10WR855 1-216-833-11 METAL CHIP 10K 5% 1/10WR856 1-216-833-11 METAL CHIP 10K 5% 1/10WR858 1-216-841-11 METAL CHIP 47K 5% 1/10W

R859 1-216-864-11 SHORT CHIP 0R862 1-216-821-11 METAL CHIP 1K 5% 1/10WR863 1-216-833-11 METAL CHIP 10K 5% 1/10WR864 1-216-841-11 METAL CHIP 47K 5% 1/10WR865 1-216-845-11 METAL CHIP 100K 5% 1/10W

R866 1-216-833-11 METAL CHIP 10K 5% 1/10WR867 1-216-853-11 METAL CHIP 470K 5% 1/10W

R868 1-216-821-11 METAL CHIP 1K 5% 1/10WR869 1-216-821-11 METAL CHIP 1K 5% 1/10WR870 1-216-821-11 METAL CHIP 1K 5% 1/10W

R871 1-216-821-11 METAL CHIP 1K 5% 1/10WR872 1-216-821-11 METAL CHIP 1K 5% 1/10WR873 1-216-813-11 METAL CHIP 220 5% 1/10WR874 1-216-813-11 METAL CHIP 220 5% 1/10WR875 1-216-821-11 METAL CHIP 1K 5% 1/10W

R876 1-216-821-11 METAL CHIP 1K 5% 1/10WR877 1-216-821-11 METAL CHIP 1K 5% 1/10WR878 1-216-809-11 METAL CHIP 100 5% 1/10WR879 1-216-821-11 METAL CHIP 1K 5% 1/10WR880 1-216-821-11 METAL CHIP 1K 5% 1/10W

R881 1-216-821-11 METAL CHIP 1K 5% 1/10WR882 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR883 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR884 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR886 1-216-849-11 METAL CHIP 220K 5% 1/10W

R887 1-216-849-11 METAL CHIP 220K 5% 1/10WR888 1-216-849-11 METAL CHIP 220K 5% 1/10WR891 1-216-821-11 METAL CHIP 1K 5% 1/10WR892 1-216-813-11 METAL CHIP 220 5% 1/10WR893 1-216-841-11 METAL CHIP 47K 5% 1/10W

R894 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR895 1-216-821-11 METAL CHIP 1K 5% 1/10WR896 1-216-833-11 METAL CHIP 10K 5% 1/10WR899 1-216-833-11 METAL CHIP 10K 5% 1/10WR900 1-216-821-11 METAL CHIP 1K 5% 1/10W

R901 1-216-821-11 METAL CHIP 1K 5% 1/10WR902 1-216-821-11 METAL CHIP 1K 5% 1/10WR903 1-216-821-11 METAL CHIP 1K 5% 1/10WR950 1-216-825-11 METAL CHIP 2.2K 5% 1/10WR951 1-216-825-11 METAL CHIP 2.2K 5% 1/10W

R952 1-216-825-11 METAL CHIP 2.2K 5% 1/10WR953 1-216-825-11 METAL CHIP 2.2K 5% 1/10WR954 1-216-833-11 METAL CHIP 10K 5% 1/10WR955 1-216-833-11 METAL CHIP 10K 5% 1/10WR956 1-216-841-11 METAL CHIP 47K 5% 1/10W

R957 1-216-825-11 METAL CHIP 2.2K 5% 1/10WR958 1-216-825-11 METAL CHIP 2.2K 5% 1/10WR959 1-216-821-11 METAL CHIP 1K 5% 1/10WR960 1-216-821-11 METAL CHIP 1K 5% 1/10WR961 1-216-821-11 METAL CHIP 1K 5% 1/10W

< VIBRATOR >

X801 1-813-175-21 VIBRATOR, CERAMIC (4.19MHz)X802 1-795-915-11 VIBRATOR, CRYSTAL (32.768kHz)

************************************************************

A-1105-360-A POWER BOARD, COMPLETE**********************

1-533-233-31 FUSE HOLDER

< CAPACITOR >

C901 1-162-995-11 CERAMIC CHIP 0.022uF 50VC902 1-162-995-11 CERAMIC CHIP 0.022uF 50VC903 1-162-995-11 CERAMIC CHIP 0.022uF 50V

POWERMAINVer. 1.2

46

ZS-SN10

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark

C904 1-162-995-11 CERAMIC CHIP 0.022uF 50VC906 1-126-964-11 ELECT 10uF 20% 50V

C908 1-165-128-11 CERAMIC CHIP 0.22uF 16V

< CONNECTOR >

CN903 1-815-551-11 PIN, CONNECTOR (PWB) 3P

< DIODE >

D901 8-719-063-79 DIODE 1N4002BD902 8-719-063-79 DIODE 1N4002BD903 8-719-063-79 DIODE 1N4002BD904 8-719-063-79 DIODE 1N4002B

************************************************************

A-1105-354-A TUNER BOARD, COMPLETE (US, CND, E, MX)A-1105-355-A TUNER BOARD, COMPLETE

(SP, TW, KR, TH, AUS)**********************

2-582-141-01 TERMINAL, ANT

< CAPACITOR >

C1 1-162-923-11 CERAMIC CHIP 47PF 5% 50VC4 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50VC7 1-162-910-11 CERAMIC CHIP 5PF 0.25PF 50VC8 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50VC9 1-162-915-11 CERAMIC CHIP 10PF 0.5PF 50V

C10 1-126-960-11 ELECT 1uF 20% 50VC11 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16VC12 1-126-963-11 ELECT 4.7uF 20% 50VC13 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V

(US, CND, E, MX)C14 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V

(SP, TW, KR, TH, AUS)

C14 1-164-227-11 CERAMIC CHIP 0.022uF 10% 25V(US, CND, E, MX)

C15 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V(SP, TW, KR, TH, AUS)

C15 1-164-227-11 CERAMIC CHIP 0.022uF 10% 25V(US, CND, E, MX)

C18 1-126-923-91 ELECT 220uF 20% 10VC20 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V

C21 1-126-960-11 ELECT 1uF 20% 50VC22 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16VC23 1-126-960-11 ELECT 1uF 20% 50VC24 1-162-960-11 CERAMIC CHIP 220PF 10% 50VC26 1-162-927-11 CERAMIC CHIP 100PF 5% 50V

C27 1-162-927-11 CERAMIC CHIP 100PF 5% 50VC29 1-104-658-91 ELECT 100uF 20% 10VC30 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25VC31 1-162-919-11 CERAMIC CHIP 22PF 5% 50VC32 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V

C33 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25VC34 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25VC35 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25VC37 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25VC39 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V

C41 1-164-230-11 CERAMIC CHIP 220PF 5% 50VC42 1-162-927-11 CERAMIC CHIP 100PF 5% 50V

C43 1-162-919-11 CERAMIC CHIP 22PF 5% 50VC47 1-162-915-11 CERAMIC CHIP 10PF 0.5PF 50VC49 1-161-051-00 CERAMIC 0.01uF 10% 25V

C51 1-162-919-11 CERAMIC CHIP 22PF 5% 50VC52 1-162-915-11 CERAMIC CHIP 10PF 0.5PF 50VC53 1-137-190-91 FILM 0.22uF 5% 50VC54 1-126-923-91 ELECT 220uF 20% 10VC55 1-162-927-11 CERAMIC CHIP 100PF 5% 50V

C56 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50VC57 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50VC59 1-162-927-11 CERAMIC CHIP 100PF 5% 50VC60 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50VC61 1-162-927-11 CERAMIC CHIP 100PF 5% 50V

C62 1-162-927-11 CERAMIC CHIP 100PF 5% 50VC63 1-162-927-11 CERAMIC CHIP 100PF 5% 50VC65 1-126-963-11 ELECT 4.7uF 20% 50VC66 1-162-927-11 CERAMIC CHIP 100PF 5% 50VC68 1-162-927-11 CERAMIC CHIP 100PF 5% 50V

C77 1-162-968-11 CERAMIC CHIP 0.0047uF 10% 50V(SP, TW, KR, TH, AUS)

C78 1-162-968-11 CERAMIC CHIP 0.0047uF 10% 50V(SP, TW, KR, TH, AUS)

C80 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25VC95 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V

< FILTER >

CF2 1-760-235-81 FILTER, CERAMICCF4 1-781-962-21 FILTER, CERAMIC

< CONNECTOR >

CNP1 1-568-854-11 CONNECTOR 11P

< TRIMMER >

CT1 1-141-442-91 CAP, CERAMIC TRIMMERCT3 1-141-304-21 CAP, CERAMIC TRIMMER

< DIODE >

D1 8-719-078-48 DIODE KV1471ETR-GD2 8-719-078-48 DIODE KV1471ETR-GD3 8-719-050-69 DIODE KV1520ND10 8-719-988-61 DIODE 1SS355TE-17D11 8-719-988-61 DIODE 1SS355TE-17

< IC >

IC1 6-700-512-01 IC TA2149BNIC2 8-759-483-40 IC LC72137M-TLM-E

< JUMPER RESISTOR >

JC1 1-216-864-11 SHORT CHIP 0JC2 1-216-864-11 SHORT CHIP 0JC3 1-216-864-11 SHORT CHIP 0JC4 1-216-864-11 SHORT CHIP 0JC5 1-216-864-11 SHORT CHIP 0

JC6 1-216-864-11 SHORT CHIP 0JC11 1-216-864-11 SHORT CHIP 0JC12 1-216-864-11 SHORT CHIP 0JC13 1-216-864-11 SHORT CHIP 0JC24 1-216-864-11 SHORT CHIP 0 (SP, TW, KR, TH, AUS)

POWER TUNERVer. 1.2

47

ZS-SN10

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark

JC33 1-216-864-11 SHORT CHIP 0JC34 1-216-864-11 SHORT CHIP 0

< COIL >

L1 1-409-775-11 COIL, AIR-COREL2 1-416-509-11 COIL, AIR-COREL3 1-754-117-12 ANTENNA, FERRITE-ROD (MW)

L4 1-411-234-21 COIL, AM OSCL11 1-414-142-11 INDUCTOR 1uH (US, CND, E, MX)L21 1-410-509-11 INDUCTOR 10uH

< RESISTOR >

R1 1-216-817-11 METAL CHIP 470 5% 1/10WR2 1-216-817-11 METAL CHIP 470 5% 1/10WR3 1-216-833-11 METAL CHIP 10K 5% 1/10WR4 1-216-833-11 METAL CHIP 10K 5% 1/10WR5 1-216-821-11 METAL CHIP 1K 5% 1/10W

R10 1-216-805-11 METAL CHIP 47 5% 1/10WR11 1-216-825-11 METAL CHIP 2.2K 5% 1/10WR13 1-216-821-11 METAL CHIP 1K 5% 1/10WR14 1-216-821-11 METAL CHIP 1K 5% 1/10WR24 1-216-813-11 METAL CHIP 220 5% 1/10W

R30 1-216-837-11 METAL CHIP 22K 5% 1/10WR31 1-216-829-11 METAL CHIP 4.7K 5% 1/10WR32 1-216-845-11 METAL CHIP 100K 5% 1/10WR33 1-216-833-11 METAL CHIP 10K 5% 1/10WR40 1-216-849-11 METAL CHIP 220K 5% 1/10W

R41 1-216-833-11 METAL CHIP 10K 5% 1/10WR50 1-216-821-11 METAL CHIP 1K 5% 1/10WR51 1-216-833-11 METAL CHIP 10K 5% 1/10WR52 1-216-864-11 SHORT CHIP 0R53 1-216-829-11 METAL CHIP 4.7K 5% 1/10W

R54 1-216-817-11 METAL CHIP 470 5% 1/10WR55 1-216-833-11 METAL CHIP 10K 5% 1/10WR56 1-216-813-11 METAL CHIP 220 5% 1/10WR57 1-216-809-11 METAL CHIP 100 5% 1/10WR58 1-216-825-11 METAL CHIP 2.2K 5% 1/10W

R59 1-216-825-11 METAL CHIP 2.2K 5% 1/10WR60 1-216-825-11 METAL CHIP 2.2K 5% 1/10WR61 1-216-825-11 METAL CHIP 2.2K 5% 1/10WR63 1-216-833-11 METAL CHIP 10K 5% 1/10WR65 1-216-833-11 METAL CHIP 10K 5% 1/10W

R91 1-216-813-11 METAL CHIP 220 5% 1/10WR92 1-216-813-11 METAL CHIP 220 5% 1/10WR94 1-216-821-11 METAL CHIP 1K 5% 1/10W

< TRANSFORMER >

T1 1-433-741-11 TRANSFORMER, IFT2 1-419-465-11 COIL (DET)

< VIBRATOR >

X1 1-795-449-11 VIBRATOR, CRYSTAL (75kHz)************************************************************

MISCELLANEOUS**************

6 1-831-915-11 CABLE, FLEXIBLE FLAT (4 CORE)64 1-831-926-11 CABLE, FLEXIBLE FLAT (11 CORE)105 1-452-899-11 MAGNET160 1-828-377-51 WIRE (FLAT TYPE) (23 CORE)163 1-832-404-21 WIRE (FLAT TYPE) (16 CORE)

208 1-827-720-51 WIRE (FLAT TYPE) (11 CORE)0501 8-848-483-12 OPTICAL PICK-UP (KSS-213C/C2RP1)

505 X-2162-709-2 CHASSIS ASSY (CDP), MOTOR(including M401 (SPINDLE))

ANT1 1-754-241-11 ANTENNA, TELESCOPIC0F902 1-533-450-12 FUSE, GLASS TUBE (DIA. 5) (2.5A/125V)

(US, CND, E, MX, TW)

0F902 1-533-468-12 FUSE, GLASS TUBE (DIA. 5) (T2AL/250V)(SP, KR, TH, AUS)

0J901 1-526-818-11 INLET, AC (E, MX)0J901 1-526-838-11 INLET, AC 2P (SP, TW, KR, TH, AUS)0J901 1-540-009-11 INLET, AC (US, CND)

M402 X-2625-769-1 GEAR ASSY (MB) (RP), MOTOR (SLED)

S201 1-771-853-11 SWITCH, DETECTION (LIMIT)S801 1-692-960-21 SWITCH, PUSH (1 KEY)

(CD LID OPEN/CLOSE DETECT)SP101 1-826-212-11 SPEAKER (10cm) (L-ch)SP201 1-826-212-11 SPEAKER (10cm) (R-ch)

0T901 1-435-917-22 TRANSFORMER, POWER (US, CND, E, MX, TW)

0T901 1-435-918-22 TRANSFORMER, POWER (SP, KR, TH, AUS)************************************************************

ACCESSORIES***********

0 1-590-342-12 CORD, POWER (E, MX)0 1-769-412-22 CORD, POWER (SP, TH)0 1-776-985-12 CORD, POWER (KR)0 1-782-126-11 CORD, POWER (US, CND)0 1-827-945-12 CORD, POWER (AUS)

0 1-829-433-11 CORD, POWER (TW)2-593-810-12 MANUAL, INSTRUCTION (ENGLISH)

(US, CND, E, TW)2-593-810-21 MANUAL, INSTRUCTION (FRENCH) (CND)2-593-810-31 MANUAL, INSTRUCTION (ENGLISH, SPANISH)

(SP, KR, TH, AUS)2-593-810-41 MANUAL, INSTRUCTION (FRENCH, GERMAN)

(SP)

2-593-811-11 MANUAL, INSTRUCTION (SPANISH) (E, MX)2-593-811-21 MANUAL, INSTRUCTION (KOREAN) (KR)2-593-811-31 MANUAL, INSTRUCTION

(TRADITIONAL CHINESE) (TW)2-598-716-11 MANUAL, INSTRUCTION (for SonicStage)

(ENGLISH) (US, CND, E, TW)2-598-716-21 MANUAL, INSTRUCTION (for SonicStage)

(FRENCH) (CND)

2-598-716-31 MANUAL, INSTRUCTION (for SonicStage)(ENGLISH, SPANISH) (SP, KR, TH, AUS)

2-598-716-41 MANUAL, INSTRUCTION (for SonicStage)(FRENCH, GERMAN) (SP)

2-598-717-11 MANUAL, INSTRUCTION (for SonicStage)(KOREAN) (KR)

2-598-717-21 MANUAL, INSTRUCTION (for SonicStage) (TRADITIONAL CHINESE) (TW)

TUNERVer. 1.3

48

ZS-SN10

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark

Ver. 1.1

2-598-717-31 MANUAL, INSTRUCTION (for SonicStage) (SPANISH) (E, MX)

3-267-151-01 LID BATTERY (for RMT-CYN7A)(for BLACK, SILVER)

3-267-151-21 LID BATTERY (for RMT-CYN7A) (for WHITE)A-1056-325-A REMOTE COMMANDER (RMT-CYN7A/HC)

(for SILVER)A-1109-498-A REMOTE COMMANDER (RMT-CYN7A/BC)

(for BLACK)A-1109-500-A REMOTE COMMANDER (RMT-CYN7A/WC)

(for WHITE)

X-2059-463-1 CD-ROM (APPLICATION) ASSY (SS3.0)(SonicStage)

49

ZS-SN10

Ref. No. Part No. Description Remark Ref. No. Part No. Description RemarkMEMO

2

ZS-SN10

REVISION HISTORY

Clicking the version allows you to jump to the revised page.Also, clicking the version at the upper right on the revised page allows you to jump to the next revisedpage.

Ver. Date Description of Revision

1.0 2005.04 New

1.1 2005.06 Addition of Thai model

Revision of electrical parts

Revision of mechanical parts

1.2 2005.07 Addition of E model

1.3 2006.02 Addition of silver type to US model

Revision of electrical parts

1.4 2006.03 Addition of silver type to Canadian model

Revision of mechanical parts