Solid HDPE  Plastic Lockers 

ROYAL LOCKERS

 

STANDARD CONFIGURATIONS AND OPTIONS 

Never needs painting, 10 standard colors 

Impervious to moisture and cleaners 

Full Plastic Hinge and Strike 

Vandal resistant welded construction 

Wide range of sizes and configurations 

ADA compliant 

 

SIZE‐TIER OPTIONS 

Standard:  

HEIGHT  WIDTH  DEPTH  Tiers 24  12”,15”,18”  12”, 15”, 18”, 21”  1, 2,  36  12, 15”, 18”  12”, 15”, 18”, 21”  1, 2, 3, 48”  12”,15”,18”  12”, 15”, 18”, 21”  1, 2, 3, 4,  60”  12”,15”,18”  12”, 15”, 18”, 21”  1, 2, 3, 4, 5, 6 72”  12”,15”,18”  12”, 15”, 18”, 21”  1, 2, 3, 4, 5, 6. 

Larger sizes are not practical in all situations please call to confirm. 

Custom sizes are available 

STYLE OPTIONS 

Lockers: 

ITEM  DESCRIPTION ‐OPTION Standard  Box Type, Single or Multi Tier Z Locker  Two tier Z Style Athletic Locker  Open Style with lockable seat storage, coat rod, and  valuables locker. Tops  Flat or Slope Bases  3” high Black base 3/4” thick Handle  Vertical friction free design Locks  Padlock, Built in Combination, Key Lock, Digi‐Lock, Coin operation. Hooks  Double Prong Black Ceiling hook or Metal J Hook Rods  Plastic or metal. Hinges  Corrosion Proof Full length Integral Plastic Hinge Venting  Slotted or Mesh Colors  Bone, Glacier Grey, Dove Gray, Military Gray, Mocha, Forest Green, 

Blueberry, Black, Red, Burgundy. 

SPECIFICATION 

Doors and Frames:  Constructed from ½” thick high density polyethylene (HDPE) homogeneous color with orange peel finish texture. Full‐length finger joint 

design providing uniform frame and vandalism prevention. Frames are one piece construction. 

Sides, tops, bottoms, dividers and shelves: 

Constructed from 3/8” thick white HDPE with Matt finish. Sides and back of box are formed from a single sheet of HDPE with fused corners. 

Top and bottom dividers are captured into corresponding grooves and connected without metal fasteners. Shelves provided in one tier 

lockers only are slid into corresponding grooves in sides and back. Shelves are located 12” from locker top. 

Latch Bar: 

Full‐length latch bar is constructed of ½” thick colored high density polyethylene with a orange peel finish color matched to the door. Latch 

bar runs the entire length of the door providing continuous security latching system. Latch lifts up to open door and returns to closed 

position after the door is closed.  

Hinge: 

Full‐length continuous hinge integrated with both door and frame. All plastic construction without any steel or metal parts. Color to match 

locker. Corrosion proof, impervious to moisture, chemicals and UV rays. 

Handle: 

Handle is ADA compliant solid plastic color matched. Friction free design with concealed connections, tamperproof operating independently 

of latch bar. 

Hasp: 

Hasp is 11 gauge (1/8”) stainless steel. Accepts standard padlocks. 

Coat hook: 

Double coat hook constructed of black poly carbonate. Furnished in 36”, 48”, 16”, and 72” one tier and 60” and 72” two tier lockers only. 

Hook is mounted under shelves in one tier and under locker top in two tier lockers. Secured to shelves and tops with stainless steel screws. 

Base: 

Bases constructed of ¾” thick  black HDPE. Standard base height is 3” high ( custom heights available) 

Flat Top: 

Flat Tops are constructed from ½” thick HDPE color matched to lockers. 

Slope Tops: 

Slope Tops are constructed from ½” thick HDPE color matched to lockers. Slope tops are attached with back plate and secured from inside of 

the locker without exposed screws on the outside of the panels. 

End Panel: 

End Panels are constructed from ½” thick HDPE color matched to lockers. Used at exposed ends. 

 

Filler Panel: 

Filler Panels are constructed from ½” thick HDPE color matched to lockers. Used to complete uneven length runs and to close gaps at walls. 

Number Plate: 

Number Plates are fabricated from aluminum with black numbers secured with rivets and located with factory pre‐drilled holes. Field 

installed. 

Mesh Doors: 

Full Mesh Doors provide ventilation especially for damp environments. 

Built In Key Lock: 

Built In Key Lock replaces the standard hasp. Key can only be removed from lock when in locked position. Master key provided. Two keys 

supplied for each lock. 

Built in Combination Lock: 

Built‐In Combination Lock replaces the standard hasp. Master key provided. Programmable with five combinations per lock. 

Coin Retain Lock: 

Safe O Mat® replaces standard HASP. Available to use either tokens or quarters. User inserts coins or tokens to lock door and release key. 

When locker door is opened with key the key is retained in the lock. 

Coin return lock: 

Safe O Mat® coin lock replaces standard hasp. Available using tokens or quarters. When locker door is opened with key, the key is retained in 

the lock and coin or token is returned. 

DigiLock®: 

ADA compliant battery operated electronic lock. 

Coat Rod: 

Coat Rod is constructed from PVC and mounted with plastic pole sockets and stainless steel screws. 

Drain holes: 

Optional drainage slots are placed in the bottom of the locker to allow for hose down. 

Wall Hook: 

Black powder‐coated zinc wall hooks available.  

Logos: 

Custom engraved logos machined into the door.  

 

 

 

DETAIL  

 

Tier Options, 1, 2, 3, 4, and 6 tiers typical. Shown with standard vent 

and mesh option. 

 

 

 

 

 

 

“Z” LOCKER (SEE AVAILABLE SIZES)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

COLORS 

 

 

Military G

ray 

Dove Grey 

Glacie

r Grey 

Bone 

Mocha 

Forre

st Green 

Vivid

 Red 

Burgu

ndy 

Black 

Blueberry 

           

 

 

 

 

 

 

 

 

 

 

 

 

Hardware 

 

   

 Plastic Hinge  Vent 

 Welded Dovetail 

 Welded Box 

 Number Plate 

 Continuous Strike 

 Hasp 

 Handle 

 Stainless Screws 

  Hook 

  Padlock 

  Built in Combination Lock 

 Coin/Token Lock 

 Key Lock   

DigiLock  

SECTION-10500

Guide Specification: Lockers and Locker Benches

Royal Plastic Lockers. (NOTE; some parts of this spec require custom information specific

to your project) Part 1 –GENERAL 1.1 WORK OF THIS SECTION A. The work of this section includes providing solid plastic polymer lockers and Benches. 1.2 RELATED SECTIONS A. The WORK of the following Section applies to the WORK of this Section. Other Sections of the

Specifications, not referenced below, shall also apply to the extent required for proper performance of this WORK.

1. Section 03300 Cast-in-Place Structural Concrete 2. Section 08710 Finish Hardware

1.3 CODES A. The WORK of this Section shall comply with the current editions of the following codes as

adopted by the Local code, if applicable. 1. Uniform Building Code

1.4 STANDARD SPECIFICATIONS A. Except as otherwise indicated, the current editions of the following apply to the WORK of this

Section:

ASTM B 209 Aluminum and Aluminum-Alloy Sheet and Plate ASTM B 221 Aluminum and Aluminum-Alloy Extruded Bars, Rods, Wire,

Shapes, and Tubes ASTM B 241 Aluminum and Aluminum-Alloy Seamless Pipe and Seamless

Extruded Tube 1.5 SHOP DRAWINGS AND SAMPLES A. The following shall be submitted in compliance with Section 01300:

1. Manufacturer’s catalogs containing technical data and installation instructions, shop drawings, and

colors available. 2. Samples of all the materials, finish, and color. The samples shall be clearly marked to show

the manufacturer’s name and product identification. The manufacturer shall offer scale model and full set of color samples.

3. Shop drawings for solid plastic locker benches, verifying all dimensions affecting the

installation. Lockers and benches shall be shown in detail, including method of installation, required fillers, trim, and accessories. Locker numbering sequence information shall be provided if indicated.

1.6 PRODUCT DELIVERY, STORAGE, AND HANDLING A. Delivery of Materials: Products shall be delivered in original, unbroken packages, containers, or

bundles bearing the name of the manufacturer. B. Storage: Products shall be carefully stored in a manner that will prevent damage and in an area

that is protected from the elements. C. Solid plastic locker and benches shall not be delivered until the building is enclosed and ready for

locker installation.

D. Solid plastic locker and bench finishes, as well as adjacent surfaces and materials shall be protected from damage or marring during installation.

PART 2 – PRODUCTS 2.1 MATERIALS, GENERAL A. Solid Polyethylene Resin: High density, solid polymer resin formed under high pressure, with

homogenous color throughout. Provide material with seamless construction with edges rounded and free from saw marks. Colors as selected by the architect from manufacturer’s standards.

1. Internal Sides, Shelves, Tops and Bottoms: Fabricated from high impact, high density,

polyethylene (HDPE) 3/8" thick with homogenous natural white color throughout.

2. Doors, Door frames, Trim and End panels: Made from high density polyethylene (HDPE) Solid plastic 1/2" thick with homogeneous color throughout. Injection molded components not acceptable.

3. Base; Lockers to be installed on a 3" high base. (bases are an optional item)

4. Material Testing: All solid plastic components shall resist deterioration and discoloration

when subjected to the following chemicals and tested in accordance with corrosion-testing procedure established by the United States Plastic Corporation:

Acetic Acid 80% Caustic Soda Nicotine Ammonium Phosphate Cooper Chloride Lime Sulfur Acetone Chlorine Water Soaps Ammonia Liquid Core Oils Potassium Bromide Bleach 12% Hydrochloric Acid 40% Trisodium Phosphate Brine Hydrogen Peroxide 30% Sodium Bicarbonate Borax Isopropyl Alcohol Urea and Urine Citric Acid Lactic Acid 25% Vinegar

B. Hardware:

1. Latch: Continuous spring loaded slide latching mechanism that is capable of accepting a

padlock and shall be securely fastened to the door. Latch mechanism shall be color matched to the locker, attached to the entire length of the door providing a continuous security latch.

2. Handle: Plastic Handle color matched to locker. ADA compliant operating with less than 5 lbs of force. Latch handle to operate independently of latch bar.

3. Hinges: Continuous, integrated into the full length of the door and locker frame, made from entirely plastic to color match the locker. Metal knuckles or pins not acceptable.

4. Coat Hooks: Two prong type made from high impact plastic attached with theft resistant screws or rivets. One hook per opening in lockers 30” high or greater.

2.2 FABRICATION, GENERAL A. Construction: Lockers shall be fabricated square, rigid, and without warp, with faces flat and free

of dents, scratches or chips. B. Solid plastic locker components shall be secured using dado routing and continuous welds and

shall provide a solid and secure construction. Adjacent lockers shall not share a common side panels.

C. Ventilation: Slotted vents shall be provided in door face as follows:

1. Single and Double-tier lockers shall have not less than 6-slotted openings top and bottom. 2. Multi-tier lockers shall have not less than 6-slotted openings at top.

2.3 LOCKER ACCESSORIES A. Locking: Lockers shall be fabricated to receive the following locking devices: (select one:

Padlock Hasp, built in combination lock, coin lock, Digi Lock) B. Number Plates: Number plates shall be manufacturer’s standard etched, embossed or stamped,

number plates with numerals not less than 3/8 inch high fastened with theft resistant rivets. Lockers shall be numbered in sequence as directed by the architect. Number plates shall be attached to face of each locker door, near the top, centered using factory pre-drilled holes.

C. Filler Panels: Filler panels shall be provided where indicated or required for a complete

installation. Panels shall be fabricated of not less than ½ inch solid plastic, and finished to match locker units.

2.4 LOCKER UNITS A. Locker units shall conform to the following requirements:

1. Lockers shall consist of (example: two-person, double tier lockers (sizes by each job need) for mounting on suitable curb, securely tied in banks as indicated; provided complete with number plates. (Select type of curb material and show mounting height of base for lockers.)

2.5 MANUFACTURERS A. Products of the types indicated shall be as manufactured by one of the following (or approved

equal by architect):

Royal Lockers as Represented by Service Oriented Sales Ph (877) 767-4636 PART 3 – EXECUTION 3.1 LOCKERS A. Lockers shall be fastened to the structures in accordance with manufacturer’s printed

recommendations and in conformance with the Uniform Building Code. Frames and doors shall form a flush exterior when installed. Lockers shall be plumb, level, rigid and securely fastened in banks.

B. Fastenings shall be spaced not more than 48 inches on center, and applied through back-up reinforcing plates where necessary to avoid distortion. Fasteners shall be concealed insofar as possible.

C. Locker shall be jointed side by side with stainless steel theft resistant through bolts.

D. Trim filler panels shall be installed where indicated. Using concealed fasteners to provide flush, hairline joints against adjacent surfaces.

3.2 LOCKER ROOM BENCHES (option, if needed) A. Bench tops to be 9 ½” wide and 1 ½” thick with all edges machined to a ¼” radius and all

exposed edges free of saw marks.

B. Solid polyethylene resin benches shall be installed in compliance with manufacturer’s instruction. C. Pedestal leg shall 2” Dia. and base to be 6” Dia. extruded anodized black aluminum.

D. Secure to floor with stainless steel expansion anchors.

3.3 ADJUST AND CLEAN A. Doors and latches shall be adjusted to operate easily without binding. Integral locking devices

shall be verified as operating properly. B. Marred finishes shall be touched up, but units that cannot be restored to factory-finished appearance

Shall be replaced. Only materials and procedures recommended or furnished by locker manufacturer shall

be used.