Download pdf - [email protected] 800.555 · *Based on 30 PSIG inlet pressure and 20% droop | **Indicates vent orientation over pressure taps The MEGR-1122H Series Domestic Regulators are used to

800.555.1234 [email protected]

A

A

A

A

A

A

A

MTankCo Supply, LLC is an equipment distributor in the LP gas industry. Weconcentrate on offering our customers options when it comes to propane equipment.With a large assortment of products and the knowledge to support our customers westrive to be your dedicated distributor in the LP gas industry.

Our mission is to provide the leadership to advance the propane industry, thecommitment to provide the best products and services available, and the integrity tobe a responsible and ethical industry leader.

MTankCo has been distributing propane equipment and heaters for over 50 years andhas always been customer oriented. We first started as McCarson Wholesale Supplyin the late 1950’s out of a small building behind Mr. McCarson’s house in Walls, MS. In April of 1981, Mr. McCarson decided to pass his legacy onto Minor and Terry Smithand operated out of the same small building in Walls, MS as Smith’s LP Supply Company. The expansion of Smith’s LP Supply Company was inevitable and in 1984 we strategically purchased a larger facility in Southaven, MS where it operates today.More recently in June 2013, Mississippi Tank Company acquired Smith’s LP to createMTankCo. The creation of MTankCo will allow existing and new customers to receivethe same quality service while offering the ability to choose from an expanding equipment line.

Mississippi Tank Company lends over 65 years of experience in the propane gasindustry as well as other compressed gases. They have been manufacturing tanks fortrucks, transports, and storage facilities since the early 1950’s and offering services such as tests, inspections, and repairs. Mississippi Tank Company is the largest manufacturer of transports in the US and has continued to expand its Hattiesburg,MS and Vincennes, IN facilities to best serve their growing base of customers. The combined experience of Mississippi Tank Company and MTankCo Supply will allow ourcustomers to have not only an array of products to choose from, but to have great service to assist them in their LP gas equipment needs.

MTankCo Supply, LLC Headquarters3000 W. 7th St.Hattiesburg, MS 39401 | 601.264.1800

OUR STORY

Customer Service 800.235.3528 | Fax 662.349.1346 | Online Sales [email protected]

Distributor of Gas Products

Main Office7074 302 Industrial Dr.Southaven, MS 38671 | 662.349.0445

Midwest Division1301 E. Elkhorn Rd.Vincennes, IN 47591

Export DepartmentMTC Export DeptTel + 972.479.0333 | Fax + [email protected]

H

I

K

L

M

DJ

M

H

I

K

L

J

Breakaway Couplings ..........................................................................................172Autogas Dispensers ............................................................................................173Fuel Management Equipment ............................................................................. 174Autogas Accessories ...........................................................................................175Thermometers & Gauges ....................................................................................176QCC Caps, Adapters, and Connectors .......................................................177 - 180

SECTION IPOL Adapters .............................................................................................181 - 185 Flare/Brass Fittings .....................................................................................186 - 188Copper Tubing .............................................................................................189 - 190Corrugated Stainless Steel Tubing .......................................................................190Gas Piping ..................................................................................................191 - 194Plastic Pipe ..........................................................................................................194Con-Stab Fittings ........................................................................................195 - 196Risers ..................................................................................................................197Appliance Connectors .........................................................................................198

SECTION JDomestic Tank Valves and Accessories ......................................................199 - 214 Cylinders, Tanks, Cylinder Valves, and Accessories ....................................215 - 224

SECTION KSafety Equipment Decals and Signs ................................................................................. 225 - 228 Pressure Gauge Snubbers and Leak Detectors ............................................ 229 Hose Barbs, Ferrules and Menders .............................................................. 230 Pressure Test Blocks and Test Kits ................................................................ 231 Low Pressure Adapters, Pressure Test Gauges, and Accessories ....... 232 - 235 Manometers ................................................................................................. 236 Gas Detectors ..................................................................................... 237 - 238 Magnehelic Gauges and Pipe Thread Sealant ............................................... 238 Anode Bags and Cathodic Protection Equipment ......................................... 239 Lock Caps and POL Locks ................................................................... 239 - 240 Scales and Scale Parts ......................................................................... 240 - 241

SECTION LTools and Accessories ............................................................................... 242 - 244

SECTION MOutdoor and Camping Accessories Camping Tees, Elbows, and Assemblies ............................................. 245 - 246 Camping Fittings ........................................................................................... 247 Flow-Longer and Stay-Longer Kits ...................................................................... 248 Quick Connectors ......................................................................................... 249 Propane Hoses and Accessories ............................................................... 249 - 250 Propane Brass Fittings .................................................................................. 250

SECTION NGeneral Information ................................................................................... 251 - 254

CONTENTSCONTENTSSECTION A PAGE

Regulators ....................................................................................................... 1 - 28Pigtails and Hogtails ...................................................................................... 29 - 30

SECTION BInternal Valves and Accessories .................................................................... 31 - 51

SECTION CActuators and Accessories ............................................................................ 51 - 53Emergency Shutoff Valves and Accessories .................................................. 54 - 59

SECTION DRelief Valves .................................................................................................. 60 - 70Bypass Valves ................................................................................................ 71 - 75Excess Flow Valves ....................................................................................... 75 - 77Back Check Valves ......................................................................................... 78 - 81Needle Valves ....................................................................................................... 81Vent Valves .................................................................................................... 82 - 834 Bolt & Socket Weld Adapters ..................................................................... 84 - 87Globe and Angle Valves ................................................................................. 88 - 95Y-Strainers ............................................................................................................. 96

SECTION EBall Valves .....................................................................................................97 - 101Hose Assemblies ................................................................................................102

SECTION FFittings (Galvanized, Black Iron, and Forged Steel) .....................................103 - 104Sight Flow Swing Check Valves ..................................................................105 - 106Gauges and Accessories ............................................................................ 107 - 118

SECTION GPumps and Pump Parts .............................................................................. 119 - 132Motors .................................................................................................................133Meters and Registers .................................................................................134 - 135

SECTION HPlant and Vehicle Remote Controls ............................................................136 - 142Reels ..........................................................................................................143 - 146Hoses and Accessories ..............................................................................147 - 149Flex Connectors ..................................................................................................150Turbo-Flo Dry Break Transfer System ..........................................................151 - 152Hose End Valves and Accessories ..............................................................153 - 156Chock Blocks & Utility Bracket ............................................................................157Interlock Technology ............................................................................................158Hose End Adapters .............................................................................................159Filler and Vapor Couplings ...................................................................................160Acme Caps, Plugs, and Chains ...................................................................163 - 164Dispenser Valves and Adapters ..................................................................165 - 168Engine Fuel Bulkheads and Carb Fittings ............................................................169Filler Couplings and Adapters ..............................................................................170LPG Filling Heads ................................................................................................171

LEADERSHIP • INTEGRITY • COMMITMENT MTankCo.com 800.235.3528 [email protected]

1 2

A A

Item No. Type Capacity in BTU/HLPG* Inlet Outlet Outlet Adj.

Range (PSI) Outlet Set Point (PSI)

MEGR-1122H-AAJ Compact 1,000,000 1/4” FNPT 1/2” FNPT 8 - 12 10MEGR-1122H-AAJXB** Compact 1,000,000 1/4” FNPT 1/2” FNPT 8 - 12 10MEGR-1222H-BGF Compact 1,000,000 F. POL 1/2” FNPT 9 - 12 10MEGR-1222H-BGFXB** Compact 1,000,000 F. POL 1/2” FNPT 9 - 12 10MEGR-1622H-BGJ Compact 2,200,000 1/2” FNPT 1/2” FNPT 8 - 12 10MEGR-1622H-BGJ Full Size 2,200,000 1/2” FNPT 1/2” FNPT 8 - 12 10MEGR-1622H-DGJ Full Size 2,500,000 3/4” FNPT 3/4” FNPT 8 - 12 10MEGR-1622H-HGJ Full Size 2,300,000 F. POL 1/2” FNPT 8 - 12 10MEGR-1622H-JGJ Full Size 2,750,000 F. POL 1/2” FNPT 8 - 12 10



MEGR-1622H-BGK Full Size 2,100,000 1/2” FNPT 1/2” FNPT 4 - 6 5MEGR-1622H-HGK Full Size 2,200,000 F. POL 1/2” FNPT 4 - 6 5MEGR-1622H-JGK Full Size 2,650,000 F. POL 3/4” FNPT 4 - 6 5

REGULATORS REGULATORSFirst Stage Excela-Flo Domestic Regulators MARSHALL EXCELSIOR

*Based on 30 PSIG inlet pressure and 20% droop | **Indicates vent orientation over pressure taps

The MEGR-1122H Series Domestic Regulators are used to reduce LP gas tank pressures for second stage regulators (normally 10 PSIG). All MEC first stage regulators are red indicatinghigh outlet pressure. The MEGR-1122H Series offers optimal relief performance that well exceeds UL test requirements providing double failure over pressure protection when used with MEC MEGR-1622 and MEGR-1652 Serious Sound Stage regulators. All MEC Excela-Flo domestic regulators feature a 25 year recommended replacement life and exclusive tear away leak check adhesive sticker.

MEGR-1122H Series and MEGR-1222H - Offers a compact design perfect for tight applicationssuch as underground tank domes. They feature an adjustment range from 9-12 PSIG (factory set @ 10 PSIG), stainless steel internal components, fluorocarbon (FKM) seat discs, molded lip fabric reinforced diaphragms and large aluminum precision machined orifice to minimize corrosion resistance against weather or contaminated gas. Vents have 3/8” FNPT tapped portsand E-Z Grip screens located over the outlet.

MEGR-1622H Series - Offers the same features as the compact MEGR-1122H Series in a fullsize version as well as having a reinforced diaphragm for superior downstream regulation, heavyduty wrench flats, and a large 3/4” FNPT tapped drip lip vent to help prevent relief vent blockage.

*Based on 30 PSIG inlet pressure and 20% droop

First Stage Excela-Flo Domestic Regulators MARSHALL EXCELSIOR

TECHNICAL SPECIFICATIONS: Max. Inlet Pressure: 250 PSIG; Exterior Finish: Red powder coat; Orifice Size: 0.15” (Compact) 0.219”(Full); Seat Material: Fluorocarbon (FKM); Diaphragm: Fabric reinforced (NBR)/molded lip O-ring bonnet/body seal; Relief Type: Internalrelief - spring-loaded; Bonnet/Body Material: Die cast aluminum; Listings: cULus/UL144; Mounting Holes: Standard 3-1/2” center; Pressure Taps: #54 orifice 1/8” FNPT plugged (2); Relief Travel Stop: Molded in adjustment cap - gray (compact), black (full size)

These First Stage Regulators are used to reduce LP gas tank pressures for a second stage regulator (5 PSIG). All MEC first stage regulators are red indicating high outlet pressure. First stage regulator vents have 3/4” FNPT tapped ports and E-Z Grip screens located over the outlet. The MEGR-1622H series offer optimal relief performance that well exceeds UL testrequirements providing double failure overpressure protection when used with MEC MEGR-1622,MEGR-1642 and MEGR-1652 Series Second Stage regulators. All MEC Excela-Flo domestic regulators feature a 25 year recommended replacement life and our exclusive tear away leak check adhesive sticker.

TECHNICAL SPECIFICATIONS: Max. Inlet Pressure: 250 PSIG; Exerior Finish: Red powder coat; Orifice Size: .15” (compact) 7/32” (full); Seat Material: Fluorocarbon (FKM); Diaphragm: Fabric reinforced (NBR)/molded lip O-ring bonnet/body seal; Listings: cULus/UL144;Mounting Holes: Standard 3-1/2” center; Pressure Taps: #54 orifice 1/8” FNPT plugged (2); Relief Travel Stop: Molded in adjustmentcap - gray (compact), black (full size)

MEGR-1622H-JGKFull Size Series

MEGR-1122H-AAJ

MEGR-1622H-HGJ Series

MEGR-1222H



MEGR-1222HT-BGF Compact 1,000,000 F. POL/Tee 1/2” FNPT 9 - 12 10MEGR-1622HT-HGJ Full Size 2,300,000 F. POL/Tee 1/2” FNPT 9 - 12 10MEGR-1622HT-JGJ Full Size 2,750,000 F. POL/Tee 3/4” FNPT 9 - 12 10


First Stage Excela-Flo Domestic Regulators MARSHALL EXCELSIOR

These first stage F. POL tee inlet regulators are used to reduce LP gas tank pressures for a second stage regulator (normally 10 PSIG) in a multiple tank manifold installation without adapters or tees. All MEC first stage regulators are red indicating high outlet pressure. CompactFirst stage regulator vents have 3/8” FNPT tapped ports and E-Z Grip screens located over theoutlet. The MEGR-1222HT series offers optimal relief performance that well exceeds UL test requirements providing double failure overpressure protection when used with MEC MEGR-1622,MEGR-1642 and MEGR-1652 Series Second Stage regulators. All MEC Excela-Flo domestic regulators feature a 25 year recommended replacement life and our exclusive tear away leak check adhesive sticker.

MEGR-1222HTCompact Tee Inlet Series


3 4

A A

*Based on 10 PSIG inlet pressure and 20% droop | **Back mount configuration | ***Vent over outlet | ****Side outlet configuration

Second Stage Excela-Flo Domestic Regulators MARSHALL EXCELSIOR

TECHNICAL SPECIFICATIONS: Max. Inlet Pressure: 10 PSIG; Exterior Finish: Green powder coat; Orifice Size: .14” (BAF), .17” (CFF& DFF); Seat Material: Fluorocarbon (FKM); Diaphragm: Fabric reinforced (NBR)/molded lip O-ring bonnet/body seal; Relief Type: Internal relief - spring-loaded; Bonnet/Body Material: Die cast aluminum; Listings: cULus/UL144; Mounting Holes: Standard 3-1/2” center; Pressure Taps: #54 orifice 1/8” FNPT plugged (2); Relief Travel Stop: Molded in adjustment cap - gray (compact), black (full size)

These compact second stage regulators are used to reduce outlet pressures from first stageregulators (normally 10 PSI) to 11” WC in domestic installations. All MEC second stage regulators are green indicating low outlet pressure. All MEC second stage domestic regulators feature a stainless steel inlet filter screen to reduce debris from passing through the regulator. All MEC Excela-Flo domestic regulators feature a 25 year recommended replacement life and our exclusive 3-part tear away leak check adhesive sticker.

MEGR-1222 and MEGR-1252 Series - Offers a second stage regulator design perfect for lower BTU applications. They feature an adjustable range from 9.5 - 13” WC (factory set @ 11” WC), stainless steel internal components, fluorocarbon (FKM) seat discs, molded lip fabric reinforced diaphragms and large aluminum precision machined orifices providing superior downstream regulation and maximum corrosion resistance against weather or contaminated gas. The MEGR-1222 Series have both the inlet and outlet in line where the MEGR-1252 serieshave a rear discharge back mount outlet for convenient wall mount applications.

MEGR-1622 and MEGR-1652 Series - Offers the same features as the compact MEGR-1222 Series in a full size, high capacity version. MEC full size second stage regulators have a large fabric reinforced diaphragm for superior downstream regulation, heavy duty wrench flats, anda large 3/4” FNPT tapped drip lip vent to help prevent relief valve blockage. The MEGR-1622Series has the inlet and outlet in line where the MEGR-1652 Series has a back mount outlet.

The MEGR-1642 Series Regulators features an adjustable range from 9 - 13” WC (factory set@ 11” WC), stainless steel internal components, fluorocarbon (FKM) seat discs, molded lip fabricreinforced diaphragms and large aluminum precision machined orifices providing superior downstream regulation and maximum corrosion resistance against weather or contaminated gas.Our full size second stage regulators have a large fabric reinforced diaphragm for superior downstream regulation, heavy duty wrench flats, and a large 3/4” FNPT tapped drip lip vent to help prevent relief valve blockage. The MEGR-1642 Series has the outlet at 90 degrees from the inlet making it ideal for vapor meter installations.

MEGR-1622Full Size Series

MEGR-1652Back Mount Series

MEGR-1222-BAFCompact Series

MEGR-1642-DFFwith Side Outlet

MEGR-1252-BAFCompact Series

REGULATORS REGULATORS

Item No. Type Capacity in BTU/HLPG* Inlet Outlet

Outlet Adj. Range

(“WC)

Outlet Set Point (“WC)

MEGR-1222-BAF Compact 500,000 1/2” FNPT 1/2” FNPT 9.5 - 13 11MEGR-1222-CFF Compact 800,000 1/2” FNPT 1/2” FNPT 9.5 - 13 11

MEGR-1222-DFF Compact 800,000 3/4” FNPT 3/4” FNPT 9.5 - 13 11

MEGR-1252-BAF** Back Mount 500,000 1/2” FNPT 1/2” FNPT 9.5 - 13 11MEGR-1252-CFF** Back Mount 650,000 1/2” FNPT 3/4” FNPT 9.5 - 13 11MEGR-1252-DFF** Back Mount 700,000 3/4” FNPT 3/4” FNPT 9.5 - 13 11MEGR-1622-BCF Full Size 710,000 1/2” FNPT 1/2” FNPT 9 - 13 11MEGR-1622-CFF Full Size 1,300,000 1/2” FNPT 3/4” FNPT 9 - 13 11MEGR-1622-CFFXO*** Full Size 1,300,000 1/2” FNPT 3/4” FNPT 9 - 13 11MEGR-1622-DFF Full Size 1,300,000 3/4” FNPT 3/4” FNPT 9 - 13 11MEGR-1622-DFFXO*** Full Size 1,300,000 3/4” FNPT 3/4” FNPT 9 - 13 11MEGR-1642-DFF**** Side Outlet 900,000 3/4” FNPT 3/4” FNPT 9 - 13 11 MEGR-1652-CFF** Back Mount 1,000,000 1/2” FNPT 3/4” FNPT 9 - 13 11MEGR-1652-DFF** Back Mount 1,000,000 3/4” FNPT 3/4” FNPT 9 - 13 11


Outlet Adj. Range

(“WC)


MEGR-1232-BBF Compact 450,000 1/4” FNPT 1/2” FNPT 9.5 - 13 11MEGR-1232-BBFXA** Compact 450,000 1/4” FNPT 1/2” FNPT 9.5 - 13 11

MEGR-1232-HBF Compact 450,000 F. POL 1/2” FNPT 9.5 - 13 11MEGR-1232-HBFXA** Compact 450,000 F. POL 1/2” FNPT 9.5 - 13 11MEGR-1232-HFF Compact 625,000 F. POL 3/4” FNPT 9.5 - 13 11MEGR-1232-HFFXA** Compact 625,000 F. POL 3/4” FNPT 9.5 - 13 11MEGR-1632-BCF Full Size 700,000 1/4” FNPT 1/2” FNPT 9 - 13 11MEGR-1632-BCFXA** Full Size 700,000 1/4” FNPT 1/2” FNPT 9 - 13 11MEGR-1632-CFF Full Size 950,000 1/4” FNPT 3/4” FNPT 9 - 13 11MEGR-1632-CFFXA** Full Size 950,000 1/4” FNPT 3/4” FNPT 9 - 13 11MEGR-1632-HCF Full Size 700,000 F. POL 1/2” FNPT 9 - 13 11MEGR-1632-HCFXA** Full Size 700,000 F. POL 1/2” FNPT 9 - 13 11MEGR-1632-JFF Full Size 900,000 F. POL 3/4” FNPT 9 - 13 11MEGR-1632-JFFXA** Full Size 900,000 F. POL 3/4” FNPT 9 - 13 11

*Based on 30 PSIG inlet pressure and 20% droop | **Indicates regulator vents opposite pressure tap ports

Integral Two Stage Excela-Flo Domestic Regulators MARSHALL EXCELSIOR

The MEGR-1232 Compact Series and the MEGR-1632 Full Size Series Regulators combine thefirst and second stage regulator set-up into one convenient unit converting tank pressure to11” WC. All MEC integral two stage domestic regulators are gray indicating low outlet pressure.Integral two stage regulators are recommended for installations with short piping distances, but provide the same advantages of two stage regulation with a single unit. All MEC integraltwo stage regulator vents have tapped ports (7/16 - 24 - First Stage) 3/8” FNPT Second Stage Compact / 3/4” FNPT Second Stage Full Size) and an exclusive E-Z grip screen located over the outlet. The MEGR-1232 and the MEGR-1632 Series both offer optimal relief performance that well exceeds UL test requirements providing over pressure protection of no more than 2 PSI downstream pressure. MEC Excela-Flo integral two stage domestic regulators feature a 25 year recommended replacement life, an exclusive Tri-Tap™ (tank, 10 PSI, 11” WC) pressure port system, and tear away leak check adhesive sticker.

MEGR-1232 Compact Series - Offers a compact integral two stage regulator design perfect for lower BTU applications and confined spaces. They feature an adjustable range from 8 - 14”WC (factory set @ 11” WC). Stainless steel integral components, fluorocarbon (FKM) seat discs,molded lip fabric reinforced diaphragms, and large precision machined aluminum orificesproviding superior downstream regulation and maximum corrosion resistance against weatheror contaminated gas. Compact series regulators feature 3/8” FNPT drip lip vent openings.

MEGR-1632 Full Size Series - Offers the same features as the compact MEGR-1232 Series in afull size, high capacity version. The full size MEGR-1632 diaphragm provides superior downstreamregulation, heavy duty wrench flats, and a large 3/4” FNPT tapped drip lip vent to help preventrelief vent blockage.

TECHNICAL SPECIFICATIONS: Max. Inlet Pressure: 250 PSIG; Exerior Finish: Gray powder coat; Orifice Size: 17” (Compact) 7/32”(Full); Seat Material: Fluorocarbon (FKM); Diaphragm: Fabric reinforced (NBR)/molded lip O-ring bonnet/body seal; Relief Type: Internalrelief - spring-loaded; Bonnet/Body Material: Die cast aluminum; Listings: cULus/UL144; Mounting Holes: Standard 3-1/2” center; Pressure Taps: #54 orifice 1/8” FNPT plugged (3); Relief Travel Stop: Molded in adjustment cap - gray (compact), black (full size)

MEGR-1232Compact Series

MEGR-1632Full Size Series


5 6

A A

Item No. Type

Capacity in Inlet Outlet

Outlet Adj. Outlet Set BTU/HLPG* Range (“WC) Point (“WC)

MEGR-1232E-BBH Compact 500,000 1/4” FNPT 1/2” FNPT 1 - 2.2 2MEGR-1232E-BBHXA** Compact 500,000 1/4” FNPT 1/2” FNPT 1 - 2.2 2MEGR-1232E-HBH Compact 500,000 F. POL 1/2” FNPT 1 - 2.2 2MEGR-1232E-HBHXA** Compact 500,000 F. POL 1/2” FNPT 1 - 2.2 2MEGR-1632E-BCH Full Size 850,000 1/4” FNPT 1/2” FNPT 1 - 2.2 2MEGR-1632E-BCHXA** Full Size 850,000 1/4” FNPT 1/2” FNPT 1 - 2.2 2MEGR-1632E-CFH Full Size 850,000 1/4” FNPT 3/4” FNPT 1 - 2.2 2MEGR-1632E-CFHXA** Full Size 850,000 1/4” FNPT 3/4” FNPT 1 - 2.2 2MEGR-1632E-HCH Full Size 900,000 F. POL 1/2” FNPT 1 - 2.2 2MEGR-1632E-HCHXA** Full Size 900,000 F. POL 1/2” FNPT 1 - 2.2 2MEGR-1632E-JFH Full Size 850,000 F. POL 3/4” FNPT 1 - 2.2 2MEGR-1632E-JFHXA** Full Size 850,000 F. POL 3/4” FNPT 1 - 2.2 2Item No. Accessory Description

ME2130 First Stage Pipe Away Elbow 1/4” M. Inverted Flare x 1/4” F. Inverted Flare

REGULATORS REGULATORSIntegral Two Stage 2 PSI Excela-Flo Service Regulators MARSHALL EXCELSIOR

The MEGR-1232E Compact Series and the MEGR-1632E Full Size Series Regulators combine thefirst and second stage regulator set-up into one convenient unit converting tank pressure to2 PSI. All MEC integral two stage 2 PSI regulators are white indicating 2 PSI outlet pressure.Integral two-stage 2 PSI regulators are recommended for installations with short pipingdistances, but provide the same advantages of two stage regulation with a single unit. 2 PSIservice regulators are used in conjunction with a LPG line regulator either at the indoor applianceor a remote manifold distribution header inlet. All MEC integral two stage regulator vent havetapped ports (7/16 - 24 - First Stage) (3/8” FNPT or 3/4” FNPT - Second Stage) and MEC’s exclusive E-Z Grip screens located over the outlet. Both the MEGR-1232E and MEGR-1632E series offer optimal relief performance that well exceeds UL test requirements providing over pressure protection of no more than 4 PSI downstream pressure.

MEC Excela-Flo integral two-stage domestic regulators feature a 25 year recommendedreplacement life, MEC’s exclusive Tri-TapTM (tank, 10 PSI, 2 PSI) pressure port system and tear away leak check adhesive sticker.

MEGR-1232E Compact Series - Offers a compact integral two-stage 2 PSI regulator design perfect for lower BTU applications and confined spaces. They feature an adjustment range from 1 - 2.2 PSI (factory set @ 2 PSI). Stainless steel integral components, fluorocarbon (FKM)seat discs, molded lip fabric reinforced diaphragms, and large precision machined aluminum orifices providing superior downstream regulation and maximum corrosion resistance against weather or contaminated gas.

MEGR-1632E Full Size Series - Offers all of the same features as the compact MEGR-1232E series in a full size high capacity version. The full size MEGR-1632E diaphragm provides superiordownstream regulation, has heavy duty wrench flats and a large 3/4” FNPT tapped drip lip ventto help prevent relief vent blockage.

TECHNICAL SPECIFICATIONS: Max. Inlet Pressure: 250 PSIG; Exerior Finish: White powder coat; Orifice Size: 17” (Compact) 7/32”(Full); Seat Material: Fluorocarbon (FKM); Diaphragm: Fabric reinforced (NBR)/molded lip O-ring bonnet/body seal; Relief Type: Internalrelief - spring-loaded; Bonnet/Body Material: Die cast aluminum; Listings: cULus/UL144; Mounting Holes: Standard 3-1/2” center; Pressure Taps: #54 orifice 1/8” FNPT plugged (3); Relief Travel Stop: Molded in adjustment cap - gray (compact), white (full size)


MEGR-1232ECompact Series

MEGR-1632E-BCHFull Size Series

Integral Second Stage Excela-Flo Domestic Regulators MARSHALL EXCELSIOR


Outlet Adj. Range

(“WC)


MEGR-1232T-HBF Compact 450,000 F. POL Tee 1/2” FNPT 9.5 - 13 11MEGR-1232T-HBFXA** Compact 450,000 F. POL Tee 1/2” FNPT 9.5 - 13 11

MEGR-1632T-HFF Compact 625,000 F. POL Tee 1/2” FNPT 9.5 - 13 11MEGR-1632T-HFFXA** Compact 625,000 F. POL Tee 3/4” FNPT 9.5 - 13 11MEGR-1632T-HCF Full Size 700,000 F. POL Tee 3/4” FNPT 9.5 - 13 11MEGR-1632T-HCFXA** Full Size 700,000 F. POL Tee 1/2” FNPT 9 - 13 11MEGR-1632T-JFF Full Size 900,000 F. POL Tee 3/4” FNPT 9 - 13 11MEGR-1632T-JFFXA** Full Size 900,000 F. POL Tee 3/4” FNPT 9 - 13 11

These integral two-stage regulators combine the first and second stage regulator set-up into one convenient unit converting tank pressure to 11” WC with the convenience of a F. POL Tee inlet for multiple tank applications. All MEC integral two-stage domestic regulators are gray indicating low outlet pressure. Integral two-stage regulators are recommended for installationswith short piping distances, but provide the same advantages of two-stage regulation with a single unit. All MEC integral two-stage regulator vent have tapped ports (7/16 -24-First Stage) (3/4” FNPT - Second Stage) and our exclusive E-Z Grip screens located over the outlet. Both theMEGR-1232T and MEGR-1632T series offer optimal relief performance that exceeds UL test requirements providing over pressure protection of no more than 2 PSI downstream pressure.MEC Excela-Flo integral twostage domestic regulators feature a 25 year recommendedreplacement life, our exclusive Tri-TapTM (tank, 10 PSI, 11” WC) pressure port system and tearaway leak check adhesive sticker.

MEGR-1232T Compact Series - Offers a compact integral two-stage regulator design perfect forlower BTU applications and confined spaces. They feature an adjustment range from 9-13” WC(factory set @ 11” WC). Stainless steel integral components, fluorocarbon (FKM) seat discs, molded lip fabric reinforced diaphragms, and large precision machined aluminum orificesproviding superior downstream regulation and maximum corrosion resistance against weatheror contaminated gas.

MEGR-1632 Full Size Series - Offers all of the same features as the compact MEGR-1232 seriesin a full size high capacity version. The full size MEGR-1632 diaphragm provides superior downstream regulation, has heavy duty wrench flats and a large 3/4” FNPT tapped drip lip vent to help prevent relief vent blockage.


TECHNICAL SPECIFICATIONS: Max. Inlet Pressure: 250 PSIG; Exerior Finish: Gray powder coat; Orifice Size: .17” (Compact) .219”(Full); Seat Material: Fluorocarbon (FKM); Diaphragm: Fabric reinforced (NBR)/molded lip O-ring bonnet/body seal; Relief Type: Internalrelief - spring-loaded; Bonnet/Body Material: Die cast aluminum; Listings: cULus/UL144; Mounting Holes: Standard 3-1/2” center; Pressure Taps: #54 orifice 1/8” FNPT plugged (3); Relief Travel Stop: Molded in adjustment cap - gray (compact), black (full size)

MEGR-1232TCompact Series

MEGR-1632T-HCFFull Size Series


7 8

A A

Item No. Inlet/Outlet Orifice

PSIG Outlet PSIG Outlet Monitor

BTU/HLPG@ BTU/HLPG@ Set Point Range 100 PSI Inlet 20 PSI Inlet

MEGR-1627/497 1” FNPT 1/2” 20 15 - 40 No 36,600,000 6,050,000MEGR-1627/576 2” FNPT 1/2” 10 5 - 20 No 45,000,000 6,003,000MEGR-1627/5810 3/4” FNPT 3/8” 10 5 - 20 No 11,700,000 4,700,000MEGR-1627/6210 3/4” FNPT 1/2” 10 5 - 20 No 12,400,000 6,700,000MEGR-1627/7710 1” FNPT 1/2” 10 5 - 20 No 25,100,000 6,900,000MEGR-1627M/267 2” FNPT 1/2” 10 5 - 20 Yes 36,100,000 6,003,000MEGR-1627M/471 1” FNPT 1/2” 10 5 - 20 Yes 25,100,000 6,900,000MEGR-1627R/113 3/4” FNPT 3/8” 10 5 - 20 Relief 9,800,000 4,200,000MEGR-1627V/7710* 1” FNPT 1/2” 10 5 - 20 No 25,100,000 6,900,000

Item No. Type


Outlet Adj. Outlet Set BTU/HLPG* Range (PSI) Point (PSI)

MEGR-1622E-BCH Full Size 1,100,000 1/2” FNPT 1/2” FNPT 1-2.2 2MEGR-1622E-DCH Full Size 1,400,000 3/4” FNPT 3/4” FNPT 1-2.2 2MEGR-1652E-DFH Backmount 1,300,000 3/4” FNPT 3/4” FNPT 1-2.2 2

Item No. Inlet/Outlet Orifice PSIG Outlet PSIG Outlet Monitor BTU/HLPG@ BTU/HLPG@

Set Point Range 100 PSI Inlet 20 PSI Inlet

MEGR-1630-104/78 2” FNPT 1/2” 10 8-20 18,900 47,000,000 7,700,000

NOTE: Other configurations and materials available upon request.

Item No. Description Inlet/Outlet Outlet Adj. Range PSIG

MEGR-6120-30 1 - 30 MEGR-6120-60 Adj. High Pressure Regulator 1/4” FNPT 1 - 60 MEGR-6120-100 1 - 100

Item No. Description Inlet/Outlet Outlet Set Point PSIG

MEGR-6121-05 5 MEGR-6121-10 10 MEGR-6121-20 20MEGR-6121-30 High Pressure Fixed Regulator 1/4” FNPT 30MEGR-6121-40 40MEGR-6121-50 50MEGR-6121-60 60

Capacities: BTU/H LPG (Vapor) Outlet Set Inlet

BTU/HR Point Pressure

50 PSI 850,000 15 PSI 100 PSI 1,700,000 150 PSI 2,500,000

20 PSI 50 PSI 900,000

100 PSI 1,800,000

40 PSI 100 PSI 1,500,000

150 PSI 2,000,000 100 PSI 1,300,000 50 PSI 150 PSI 1,800,000 200 PSI 2,300,000

MEGR-1627 Series

First Stage High Pressure Industrial Regulators MARSHALL EXCELSIOR

The MEGR-1627 Series Commercial/Industrial Regulator is a large capacity, high pressure unit for use in conjunction with MEGR-CS1200 or MEGR-S1202 Series regulators. It can also be used on final-stage (PSI to PSI) service. The diaphragm case and/or regulator body on the MEGR-1627 Series can be rotated in any of four positions to allow installation in locations with limited space. Available with a monitor or integral relief valve. The MEGR-1627 Series is perfectly suited for jurisdictional systems, grain dryers, direct fired vaporizers or other high capacity service applications.

* Viton® construction

* Based on 10 PSIG inlet pressure and 20% drop | ** Indicates back mount configuration

2 PSI Outlet Service Regulators MARSHALL EXCELSIOR

The MEGR-1622E and MEGR-1652E Series are used to reduce outlet pressures from first stageregulators (normally 10 PSI) to a nominal 2 PSI. 2 PSI service regulators are used in conjunctionwith an LPG line regulator either at the indoor appliance or a remote manifold distribution headerinlet. All Marshall Excelsior’s (MEC) 2 PSI service regulators are white with white adjustment caps. The full size 2 PSI service regulators have 3/4” FNPT tapped vents and our exclusive E-Zgrip screens located over the inlet. All MEC 2 PSI service regulators feature a stainless steel inlet filter screen to reduce debris from passing through the regulator. Both the MEGR-1622Eand MEGR-1652E series offer optimal relief performance that exceeds UL test requirements. All MEC Excela-Flo domestic regulators feature a 25 year recommended replacement life and our exclusive tear away leak check adhesive sticker.

MEGR-1622E Series: Offers a full size high capacity molded lip fabric reinforced diaphragm, stainless steel internal components, fluorocarbon (FKM) seat discs, precision machined aluminumorifices, and an adjustment range from 1-2.2 PSI (factory set @ 2 PSI) providing superior downstream regulation and maximum corrosion resistance against weather or contaminated gas.

MEGR-1652E Series: Offers all of the same features as the MEGR-1622E Series but with a rear discharge back mount outlet for convenient wall mount applications.

TECHNICAL SPECIFICATIONS: Max. Inlet Pressure: 10 PSI; Exterior Finish: Green powder coat; Orifice Size: 7/32”; Seat Material:Fluorocarbon (FKM); Diaphragm: Fabric reinforced (NBR)/molded lip O-ring bonnet/body seal; Relief Type: Internal relief - spring-loaded;Bonnet/Body Material: Die cast aluminum; Listings: cULus/UL144; Mounting Holes: Standard 3-1/2” center; Pressure Taps: #54 orifice1/8” FNPT plugged (2); Relief Travel Stop: Molded in adjustment cap - white

MEGR-1622E Series

MEGR-1652E Series

REGULATORS

The MEGR-1630 Series First Stage Industrial Regulators are large capacity, high pressure unitsfor use in conjunction with MEGR-S1202 Series regulators. They can also be used on final stage(pounds-to-pounds) service. These regulators are best suited for industrial applications where high flow capacity is required.

TECHNICAL SPECIFICATIONS for the MEGR-1627 and MEGR-1630 Series: Max. Inlet Pressure: 10 PSI; Exterior Finish: Gray powdercoat; Orifice Size: 3/8”, 5/16” or 1/2”; Orifice Material: Aluminum; Diaphragm: Fabric reinforced (NBR); Bonnet/Body Material: Die castaluminum/iron; Regulator Spring: Steel; Listings: cULus/UL144; Relief Travel Stop: Molded in adjustment cap - white; Temp. Range: -20° F / 180° F

* Approximate BTU/H vapor capacities taking 10-20% droop into consideration

NOTE: Side Outlet Connection Style (Plugged): 1/4” MNPT, pressure gauge (MEJ500 Series) can

be installed

High Pressure Regulators - Adjustable MARSHALL EXCELSIOR

The MEGR-6120 Series are UL listed high-pressure regulators that meet a variety ofapplications for liquid or vapor service. Thecompact body design makes them useful in installations with space limitations. The basic MEGR-6120 Series come equipped with a handwheel adjustment. The ME6121Series has a tamper-resistant spring case.

The MEGR-6120 and MEGR-6121 Series are UL listed as high pressure, non-relief regulators. They contain brass materials that are not compatible with anhydrous ammonia service.

First Stage/High Pressure Industrial Regulators (continued) MARSHALL EXCELSIOR

High Pressure Regulators - Fixed MARSHALL EXCELSIOR

TECHNICAL SPECIFICATIONS: Max. Inlet Pressure: 250 PSI (17, 2 bar); Gauge Port: 1/4” FNPT; Exterior Finish: Red wet coat; Diaphragm: Fabric reinforced Buna N; Body/Bonnet Material: Die cast aluminum; Liquid Capacity: 3-5 GPH; Listings: UL Listed /UL 144

MEGR-1630 Series

MEGR-6120 Series

MEGR-6121 Series

REGULATORS


9 10

AA

Item No. Description Primary Cylinder Reserve Cylinder

Covers Mounting

BTU/Hr.** BTU/Hr.** Bracket

MEGR-253* 2 Stage Auto Changeover Regulator 1/4” Inv. Flare x 3/8” FPT 225,000 150,000 MEGR-900

MEGR-253H* High Capacity 2 Stage Auto Changeover Reg. 1/4” Inv. Flare x 3/8” FPT 350,000 200,000 MEGR-862 or MEGR-RVBMEGR-253L* Low Capacity 2 Stage Auto Changeover Reg. 1/4” Inv. Flare x 3/8” FPT 150,000 100,000

The MEGR-253 Series Automatic Changeover Regulators automatically redirect LP gas vapor flow from an empty service cylinder to a reserve cylinder, without interruption of service. Itfeatures an easy to read green indicator which changes to red when the service cylinder needs to be refilled.

The MEGR-253H Two-stage High-pressure Regulator reduces container pressure toapproximately 10 to 15 PSIG and then the second stage completes the process by reducing inlet pressure down to 11 inches of water column outlet pressure.

The MEGR-253L is specifically intended for application with low BTU demands but still requiretwo stage regulation. The Model MEGR-253L is ideally suited for RV, manufactured homes, cabins or other applications with a single appliance or low BTU multiple appliance applicationswhile still permitting maximum range of output pressure adjustment.

The MEGR-253, MEGR-293H and MEGR-253L Series Regulators meet UL, RVIA and NFPA requirements.

TECHNICAL SPECIFICATIONS: Maximum Inlet Pressure: 250 PSIG; Exterior Finish: Raw Zinc(MEGR-253), Powder Coat (MEGR-253H); Inlet Connection: 1/4” Female inverted flare (2); Outlet Connection: 3/8” FNPT (1); Diaphragm: Fabric reinforced molded with O-ring bonnet/bodyseal; Relief Type: Internal relief - spring-loaded; Bonnet/Body Material: Die cast zinc; Listings:UL listed / UL 144; Mounting Holes: Standard 3-1/2” center; Pressure Taps: 1/8” FNPT plugged (1)

Domestic Excela-Flo Automatic Changeover Regulators MARSHALL EXCELSIOR

MEGR-253

MEGR-253HHigh Capacity

* Packaged option consists of a plastic clamshell with barcode. To order add “P” at the end of the part number i.e. MEGR-253P | ** BTU/H Capacity @20% Droop | Note: MEGR-253 and MEGR-253H set point: 100 PSIG Inlet @ 11” WC Outlet Flowing @ 30 SCFH Air; MEGR-253L set point: 100 PSIG Inlet @ 11” WC outlet flowing @ 10 SCFH Air

REGULATORS

MEGR-253LLow Capacity

These Two Stage, Automatic Changeover Regulators combine the first and second stage regulator into one unit converting full tank pressure to 11” WC. MEC Excela-Flo Automatic Changeover regulators prevent gas outages by switching supply cylinders over to the reserve cylinder automatically when the primary cylinder is near empty. When the primary cylinder is depleted causing the changeover to occur a red indicator will appear signifying the reserve cylinder in now in use and the primary cylinder can be refilled without loss of service.

MEGR-175CS61622-BCF Series: Offers all of the same features as the compactMEGR-175S61222 series but with a full size high capacity second stage regulator option. Thefull size second stage diaphragm provides superior downstream regulation and features heavyduty wrench flats and a large 3/4” FNPT tapped drip lip vent to help prevent relief vent blockage.This regulator is perfect for manifolding larger tanks together such as 420 LB cylinders.

MEGR-175CS61222-BAF Series: Offers a compact two stage regulator option for lower BTU applications such as mobile or seasonal homes. They feature a second stage adjustment from8 - 14” WC (factory set @ 11” WC), stainless steel internal components, fluorocarbon (FKM) seatdiscs, molded lip fabric reinforced diaphragms, and large precision machined aluminum orificesproviding superior downstream regulation and maximum resistance against weather orcontaminated gas. The compact second stage features a 3/8” FNPT drip lip vent.

TECHNICAL SPECIFICATIONS: Maximum Inlet Pressure: 250 PSIG; Exterior Finish: Green and gold powder coat; Orifice Size: .14” (compact) .219” (full); Seat Material: (NBR) First stage, fluorocarbon (FKM) 2nd stage; Diaphragm: Fabric reinforced (NBR)/molded lip O-ring bonnet/body seal; Relief Type: Internal relief - spring-loaded; Bonnet/Body Material: Die cast zinc/plastic first stage, die cast aluminum second stage; Listings: cULus/UL144 2nd stage; Mounting Holes: Standard 3-1/2” center; Pressure Taps: #54 orifice 1/8” FNPT plugged (1); Relief Travel Stop: Molded in adjustment cap - gray (compact), black (full size)

Automatic Changeover Regulators MARSHALL EXCELSIOR

MEGR-175CS61222-BAFCompact Series

MEGR-175CS61222-BCFFull Size Series


REGULATORS

Item No. Type Primary Cylinder Capacity BTU/HLPG(1)

Auxilary Cylinder Capacity in BTU/H LPG* Inlet Outlet Outlet Adj.

Range (“WC)Outlet Set

Point (“WC)

MEGR-175CS61222-BAF Compact 400,000 340,000 1/4” IF (2) 1/2” FNPT 9.5 - 13 11MEGR-175CS61622-BCF Full Size 650,000 570,000 1/4” IF (2) 1/2” FNPT 9 -13 11

MEGR-175CS61622E-BCH Full Size 625,000 525,000 1/4” IF (2) 1/2” FNPT 1.0-2.2 PSI 2 PSI

MEGR-175CS61622E-BCHFull Size Series


11 12

A A

Item No. Type

Inlet (1 Port) / Outlet Pressure Maximum Inlet Outlet (3 Ports) Range Pressure (PSIG) MEGR-11301F Adjustable 1/4” FNPT 0-120 5,500

Item No. Inlet/Outlet

Outlet Pressure Outlet Adj. BTU/HLPG@ Setting PSIG Range PSIG 100 PSI Inlet

MEGR-164/33 10 0 - 30 2,700,000MEGR-164/35 20 0 - 30 3,600,000MEGR-164/36 40 0 - 60 4,200,000MEGR-164/222 50 0 - 125 5,300,000MEGR-164SR/21 15 0 - 30 3,000,000MEGR-164SR/22 15 0 - 30 3,000,000MEGR-164SR/23 20 0 - 30 3,600,000MEGR-164-6/33 10 0 - 30 2,700,000MEGR-164-6/35 20 0 - 30 3,600,000MEGR-164-6/36 40 0 - 60 4,200,000MEGR-164-6/222 50 35 - 100 5,300,000

REGULATORS REGULATORSHigh Pressure Regulators MARSHALL EXCELSIOR

MEGR-164 Series - Offers a wide selection of available pressure ranges. High pressure regulatorsare typically used to reduce tank pressure to an intermediate pressure for use by another regulator. They may be used as high pressure regulators on distribution systems when used in conjunction with first stage downstream regulators.

When equipped with an integral relief valve (MEGR-164SR Series), the regulator may be usedas a final stage regulator on high pressure systems. It may also be used as a first stage regulatorwhen set at 10 PSIG or less. The 1/4” FNPT tapped side outlet can be used to install a pressuregauge or a hydrostatic relief valve. This series contains brass materials that are not compatiblewith anhydrous ammonia service.

1/2” FNPT x 1/2” FNPTAdjustable High

Pressure Regulator

1/2” FNPT x 1/2” FNPTAdj. High Pressure Regulator

w/ Internal Relief Valve

3/4” FNPT x 3/4” FNPTAdj. High Pressure Regulator

TECHNICAL SPECIFICATIONS: Max. Inlet Pressure: 250 PSI; Inlet Connection: 1/2” FNPT or 3/4” FNPT; Outlet Connection: 1/2”FNPor 3/4” FNPT; Exterior Finish: Gray urethane; Regulator Spring: Steel; Stem Guide/Disk Holder: Stainless steel; Diaphragm: Fabric reinforced nirile (NBR); Bonnet/Body Material; Cast aluminum; Vent: Non-aluminum; Listings: UL Listed/UL 144.

High Pressure Regulator MARSHALL EXCELSIOR

The MEGR-11301F is a reliable and accurate regulator making it ideal for numerous high pressureapplications. This multi-purpose regulator can be used as a pilot supply or pressure-loading regulator where high pressure operating medium must be reduced for use by gas regulator pilots or pressure-loaded regulators. Its rugged design and multiple outlet ports offer versatilityfor a wide variety of applications.

TECHNICAL SPECIFICATIONS: Type: Adjustable/PSI; Max. Inlet Pressure: 5,500 PSIG; Exterior Finish: Brass; Bonnet/Body Material:Brass; Bottom Cap and Spring Case: Brass; Gasket: Nitrile (NBR); Valve Spring: Stainless steel; Diaphragm: Stainless steel; Valve Disks: Nylon; Vent: 4 Holes (5/32” each); Temp. Rang: -40º F/225º F

High Pressure LP Gas Regulators MARSHALL EXCELSIOR

The MEGR-130 Series Fixed High Pressure Single Stage Regulators provide an economicalsolution for pounds to pounds service applications and regulates air and LP gas. Regulators mustbe installed in compliance with federal, state or local codes, or laws in accordance with NFPA 58.

MEGR-350 Single Stage, Adjustable High Pressure Regulator. The body and bonnet of both thefixed and adjustable regulators are precisely machined and feature a crimped design and fabricreinforced rubber diaphragm creating a positive seal for leak-free performance.

MEGR-360 Type I (QCC) is designed for appliances such as turkey fryers, camp stoves and torchapplications that require pounds to pounds pressure instead of inches water column. They meetor exceed most requirements on a specific outlet setting (0-10 PSI) depending on the application.

TECHNICAL SPECIFICATIONS: Type: Adjustable or fixed/PSI; Max. Inlet Pressure: 250 PSIG (17,2 bar); Orifice Diameter: 0.0625”; Exterior Finish: Red anodized; Diaphragm: Fabric reinforced Buna N; Bonnet/Body Material: Die Cast Zinc; Listings: UL Listed/UL 144

Item No. Type Max Inlet Pressure Inlet Outlet Outlet Adj.

Range (PSI) BTU/H

@ 40 PSI

MEGR-130-05 Fixed

250 PSIG 1/4” FNPT 1/4” FNPT

5

1,200,000

MEGR-130-10 Fixed 10MEGR-130-20 Fixed 20MEGR-130-30 Fixed 30MEGR-130-50 Compact 50MEGR-130-80 Compact 80MEGR-350 Adjustable 0-10MEGR-350-20 Adjustable 0-20MEGR-350-30 Adjustable 0-30MEGR-351 Adj. (Full Flow POL) 0-10MEGR-360 Adj. (Black F. QCC) 0-10

MEGR-130-20Pre-Set at 20 PSIG

MEGR-350Adjustable 0-10 PSIG

MEGR-164 Series

MEGR-11301F


13 14

A A

Item No.


Outlet Adj. Outlet Set BTU/HLPG* Range (PSI) Point (PSI)

MEGR-1HSRL-BFC 2,000,000 3/4” FNPT 3/4” FNPT 6 - 14 11MEGR-1HSRL-CFC 2,500,000 1” FNPT 1”FNPT 6 - 14 11

Outlet Outlet Max BTU/H BTU/H Item No. Inlet/Outlet Orifice Pressure Pressure Operating LPG@ LPG@ Range Setting Inlet 25 PSI Inlet 10 PSI Inlet

MEGR-CS1200IR6EC1 3/4” FNPT 1/2” 2,100,000 1,600,000 MEGR-CS1200IR6EC3 1” FNPT 1/2” 11” WC 2,500,000 1,900,000MEGR-CS1200IR6EC6 1-1/4” FNPT 1/2” 6 - 14” WC 3,100,000 2,800,000MEGR-CS1200IR7EC1 3/4” FNPT 5/16” ~1,250,000 ~985,000MEGR-CS1200IR7EC3 1” FNPT 5/16” ~1,620,000 ~1,525,000MEGR-S1202G-BNC 1-1/2” FNPT 1” 11” WC 14,700,000 10,800,000MEGR-S1202G-CNC 2” FNPT 1” 11” WC 30,000,000 23,000,000MEGR-S1202H-CNK 2” FNPT 1” 1.5-3.25 PSI 2 PSI 22,200,000 10,300,000

7” WC 25 PSIG

9 - 18” WC

MEGR-230-9 MEGR-231

REGULATORS REGULATORS

NOTE: Other configurations available upon request

MEGR-1133 Series

The MEGR-1133 Series Second Stage Industrial Regulator is a manual, direct acting,self-operating, spring loaded, adjustable regulator. It is used in applications where pressure reduction is required. The regulator will reduce the risk of “shock” from abrupt changes of downstream conditions. This can help prevent safety equipment from shutting an operation down. The MEGR-1133 is equipped with external pressure registration; an external control lineis needed to connect the output pressure port with the diaphragm chamber. The MEGR-1133 utilizes a balance diaphragm to reduce the effects of supply pressure changes on the output pressure. The external pressure registration of the standard MEGR-1133 also allows it to be used as a monitor regulator.

TECHNICAL SPECIFICATIONS: Type: Adjustable/PSI/WC; Max. Inlet Pressure: 60 PSIG; Exterior Finish: Gray powder coat; BodyMaterial: Iron; Orifice Material: Aluminum; Regulator Spring: Steel; Stem Guide/Disk Holder: Aluminum; Diaphragm: Fabric reinforcedNitrile (NBR); Valve Stem: Aluminum; Bonnet Cap and Bonnet: Aluminum

Light Commercial Second Stage Excela-Flo Regulators MARSHALL EXCELSIOR

*Based on 10 PSIG inlet pressure and 20% droop.

MEGR-1HSRL Series: These light commercial second stage regulators are used to reduce outletpressures from first stage regulators (normally 10 PSI) to 11” WC. They offer a full size, high capacity light commercial type regulator with a heavy duty cast iron body with a universal body to bonnet union for fast relocation of inlet to outlet vent location.

TECHNICAL SPECIFICATIONS: Max. Inlet Pressure: 40 PSIG; Exterior Finish: Gray powder coat; Diaphragm: Fabric reinforced (NBR);Relief Type: Internal relief - spring-loaded; Bonnet/Body Material: Die cast aluminum/cast iron; Orifice Size: 3/8”

MEGR-1HSRL Series

MEGR-230 Series

The MEGR-230 Single-Stage Regulators are approved for use in small portable applications andoutdoor cooking appliances utilizing low pressure. Single stage regulators are not approved for RV use.

TECHNICAL SPECIFICATIONS: Orifice Diameter: 0.059 Diameter; BTU Capacity: 140,000 BTU (based on 25 PSI inlet @ 9 WC deliverypressure); Max. Inlet Pressure: 250 PSI; Inlet Connection: 3/8” FNPT; Exterior Finish: Green wet coat; Diaphragm: Molded withO-ring bonnet/body seal; Bonnet/Body Material: Die cast aluminum; Listings: UL Listed/UL 144; Mounting Holes: 3-1/2” on center

NOTE: Other configurations and materials available upon request. | ~ Flow Rates listed in BTU Natural Gas | WC = Water Column

Second Stage Low Pressure Industrial Excela-Flo Regulators MARSHALL EXCELSIOR

The MEGR-S1202/MEGR-CS1200 Series commercial/ industrial regulators are large capacity, low pressure second stage units for installation at schools, bakeries, and similar applications. They contain a limited capacity internal relief valve and can be used in conjunction with either MEGR-1627 Series or MEGR-1630 Series high-pressure regulators.

For high capacity installations, the MEGR-1289H Series relief valve is required to be installed in the downstream system.

TECHNICAL SPECIFICATIONS: Type: Adjustable/inches WC or PSI; Max. Inlet Pressure: 25 PSIG (17,2 bar); Orifice Diameter: 3/8”, 5/16”, 1/2” or 1”; Exterior Finish: Gray powder coat; Body Material: Cast iron; Regulator Spring: Music wire; Spring Case/Stem Guide/ Disk Holder: Aluminum; Disk/Diaphragm and O-ring: Fabric reinforced Nitrile (NBR); Closing Cap Gasket: Neoprene

Item No. Description Inlet/Outlet Orifice Range ofAdjustment

Outlet Set Point

BTU/H@ 10 PSI Inlet

BTU/H LPG@ 20 PSI Inlet

MEGR-1133H-2 Second Stage Regulator 2” FNPT 2” 2-5 PSI 2 PSI 27,405,000 52,700,000MEGR-1133H-3 Second Stage Regulator 2” FNPT 2” 5-10 PSI 5 PSI 22,300,000 41,600,000MEGR-1133L-4 Second Stage Regulator 2” FNPT 2” 8.5”-18” WC 14” WC 45,600,000 77,100,000MEGR-1133L-6 Second Stage Regulator 2” FNPT 2” .75-2 PSI 2 PSI 46,700,000 77,100,000

Second Stage Commercial/Industrial Excela-Flo Regulators MARSHALL EXCELSIOR

Item No. Description Outlet PressureSetting

VentOrientation

MEGR-218 Single Stage Regulator - SN FF POL w/ Plastic Handwheel x 3/8” FNPT - 90° Vent

11-inches w.c.(27 mbar)

90°MEGR-230 Single Stage Regulator - 1/4” FNPT Inlet X 3/8” FNPT Outlet Over OutletMEGR-230-9 Single Stage Regulator - SN .9 GPM Excess Flow POL Inlet x 3/8” FNPT Outlet Over OutletMEGR-230-90 Single Stage Regulator - 1/4” FNPT Inlet X 3/8” FNPT Outlet - 90° Vent 90°MEGR-230-1618 Single Stage Regulator - Black F. QCC Inlet x 3/8” FNPT Outlet - 90° Vent 90°MEGR-230-1326 Single Stage Regulator - Black F. QCC Inlet (100,000 BTU/ H) x 3/8” FNPT Outlet Over OutletMEGR-231 Single Stage Regulator - Hardnose FF POL Inlet x 3/8” FNPT Outlet - 90° Vent 90°

Low Pressure Single Stage Excela-Flo Regulators MARSHALL EXCELSIOR

MEGR-S1202 Series

MEGR-CS1200 series


15 16

A A

Item No. Inlet x Outlet Orifice Sizes,

Outlet Pressure Setting Outlet Pressure Ranges, Vent BTU/H LPG @

Connection Style Inches (mm) Inches WC (mbar) Orientation 100 PSI Inlet

MEGR-1912/101 1/4” x 3/8” FNPT 0.073 (1,8) 11-inches WC (27 mbar) 9.25 - 13 (23 - 32) 242,953 MEGR-1912/104 1/4” x 1/4” FNPT 0.073 (1,8) 11-inches WC (27 mbar) 9.25 - 13 (23 - 32) 242,953 MEGR-1912/109 1/4” x 3/8” FNPT 0.073 (1,8) 7-inches WC (17 mbar) 5 - 10 (12 - 25) 242,953 MEGR-1912/197 1/4” x 3/8” FNPT 0.094 (2,4) 20-inches WC (50 mbar 12 - 24 (30 - 60) 313,488 MEGR-1912H/108 1/4” x 3/8” FNPT 0.094 (2,4) 1.5 PSI (103 mbar) 0.5 -2.7 PSI (34 - 186 mbar) Over Outlet 297,814MEGR-1912H/520 1/4” x 1/4” FNPT 0.094 (2,4) 3.5 PSI (241 mbar) 2.7- 5 PSI (186 - 345 mbar) —MEGR-1912H/534 1/4” x 1/4” FNPT 0.073 (1,8) 1.5 PSI (103 mbar) 0.5 -2.7 PSI (34 - 186 mbar) —MEGR-1912N/113 1/4” x 3/8” FNPT 0.073 (1,8) 5-inches WC (27 mbar) 3 - 7 (7 - 17) —MEGR-1912N/194 1/4” x 1/4” FNPT 0.073 (1,8) 5-inches WC (27 mbar) 3 - 7 (7 - 17) —

Item No. Description

BTU/H LPG@ Accessories 30 PSI Inlet*

MEGR-291 1/4” FNPT Inlet x 3/8” FNPT Outlet 175,000MEGR-298 1/4” FNPT Inlet x 3/8” FNPT Outlet - 90° Vent 175,000MEGR-295 HN Excess Flow POL Inlet x 3/8” FNPT Outlet - 90° Vent 175,000MEGR-291-20681 Green Type I QCC Inlet x 3/8” FNPT Outlet 175,000MEGR-298-20681 Green Type I QCC Inlet x 3/8” FNPT Outlet - 90° Vent 175,000MEGR-291H High Capacity Regulator 1/4” FNPT Inlet x 3/8” FNPT Outlet 225,000MEGR-291L Low Capacity Regulator 1/4” FNPT Inlet x 3/8” FNPT Outlet 120,000MEGR-298H High Capacity Regulator 1/4” FNPT Inlet x 3/8” FNPT Outlet - 90° Vent 225,000MEGR-298L Low Capacity Regulator 1/4” FNPT Inlet x 3/8” FNPT Outlet - 90° Vent 120,000MEGR-291H-20681 High Capacity Regulator Green Type I QCC Inlet x 3/8” FNPT Outlet 225,000MEGR-300 2 PSI Regulator 1/4” FNPT Inlet x 3/8” FNPT Outlet 225,000MEGR-300-90 2 PSI Regulator 1/4” FNPT Inlet x 3/8” FNPT Outlet - 90° Vent 225,000

REGULATORS

The MEGR-1912 Series UL Listed regulators are direct-operated, spring-loaded models designedfor use in a variety of service and industrial applications. These regulators have limited capacityinternal relief across the diaphragm to help minimize over pressurization. The MEGR-1912 Series,with capacity ratings of less than 320,000 BTU/HR (129 scfh), are often used on small portableoutdoor appliances.

Underwriters Laboratories requires horizontally mounted regulators to be installed with vent opening protection to prevent blockage by freezing rain.

TECHNICAL SPECIFICATIONS: Type: Single stage; Max. Inlet Pressure: 250 PSI; Vent Screen: Monel; Gasket: CGR 2750; Relief Valve:Brass and zinc; Control and Relief Valve Spring: Plated steel; Diaphragm Assembly: Nitrile (NBR) with zinc disk; Spring Case: Die castzinc; Spring Seat: Plated steel; Diaphragm Plate: Plated steel; Body Material/Lower Casting: Die cast zinc; Listings: UL Listed/UL 144

*NOTE: Other configurations and materials available upon request.

Pressure Reducing Regulators MARSHALL EXCELSIOR

The MEC MEGR-291 Two Stage Regulators are approved for use in nearly all portable applicationsand outdoor cooking appliances utilizing low pressure. They feature all zinc body construction, high and low 1/8” NPT pressure tap ports, an integral second stage drip lip vent and optional standard or 90 degree vent locations.

The MEGR-291H High Capacity Compact Integral Two Stage Regulator is ideal for high demandRV, outdoor appliances, seasonal homes, gas fire places, water heaters, ranges or other moderateto low demand domestic home installations. (Green bonnet identifies high capacity model).

*BTU/H Capacity @ 20% Droop | MEGR-291 and MEGR-291H Setpoint: 100 PSIG Inlet @ 11” WC Outlet Flowing @ 30 SCFH Air | MEGR-300 Setpoint: 100 PSIG Inlet @ 2 PSI Outlet Flowing @ 30 SCFH Air

Compact Integral Two Stage Excela-Flo Regulators MARSHALL EXCELSIOR

MEGR-900(Z-Bracket)

MEGR-861

(First Stage Cover)

MEGR-862(Second Stage Cover)

REGULATORS

TECHNICAL SPECIFICATIONS: Max. Inlet Pressure: 250 PSI; Inlet Connection: 1/4” FNPT; Exterior Finish: Raw zinc/powder coated; Diaphragm: Fabric reinforced molded with O-ring bonnet/body seal; Diaphragm Type: Internal relief - spring-loaded; Bonnet/Body Material: Die cast zinc; Listings: UL Listed/UL 144; Mounting Holes: 3-1/2” on center; Pressure Taps: 1/8” FNPT Plugged

The MEGR-291L Compact Integral Two Stage 2 PSI Low Capacity Regulator is specifically intended for application with low BTU demands but still require two stage regulation. The Model MEGR-291L is ideally suited for RV, manufactured homes, cabins or other applications with one appliance or low BTU multiple appliance applications while still permitting maximum range of output pressure adjustment.

The MEGR-300 Compact Integral Two Stage 2 PSI Regulator is ideally suited for installations toreduce tank pressure to a nominal 2 PSI outlet pressure. 2 PSI systems typically incorporate aline service regulator within the home that further reduces the 2 PSI system pressure toapproximately 11” WC prior to the appliance. (Red bonnet identifies 2 PSI model).

MEGR-291, MEGR-291H and MEGR-300 Series meet UL, RVIA and NFPA requirements.

MEGR-1912 Series

MEGR-291

MEGR-291H

MEGR-300

MEGR-295

MEGR-298L


17 18

A A

Item No. Inlet/Outlet

Max. Inlet Set Point

Set Point SCFH/ PSIG Range Propane

MEGR-1289H/1 2” FNPT 25 9” WC 7-18” WC 55,000MEGR-1289H/2 2” FNPT 25 1 PSIG .5-2.25 PSIG 55,500MEGR-1289H/3 2” FNPT 25 3 PSIG 1.75-7 PSIG 58,000MEGR-1289H/4 2” FNPT 25 6 PSIG 4-10 PSIG 58,500MEGR-1289H/5 2” FNPT 25 12 PSIG 10-15 PSIG 61,000MEGR-1289H/41 1” FNPT 100 2 PSIG 1-4.5 PSIG 45,500MEGR-1289H/42 1” FNPT 100 8 PSIG 4-15 PSIG 46,000MEGR-1289H/43 1” FNPT 100 15 PSIG 10-20 PSIG 48,000MEGR-1289H/49 1” FNPT 100 25 PSIG 15-50 PSIG 49,000MEGR-1289HH-1 1” FNPT 100 50 PSIG 45-75 PSIG 50,000

MEGR-1290H/43 3/4” FNPT

100 15 PSIG 10-20 PSIG 40,000 X 1” FNPT

MEGR-1290H/49 3/4” FNPT

100 25 PSIG 15-50 PSIG 50,000 X 1” FNPT

Relief Pressure

Outlet PSIG

Relief Capabilities GPM/LPGItem No. Inlet/Outlet

PSIG (BAR)

(BAR) 10 PSI Over 50 PSI Over

Set Point Set PointMEGR-198H-22 3/4” FNPT 100 (6.9) 70 - 140 (4.8 - 9.7) 49 93MEGR-198H-30 1” FNPT 100 (6.9) 70 - 140 (4.8 - 9.7) 49 93MEGR-198H-31 1” FNPT 175 130 - 200 52 109

Outlet BTU/H LPG Item No. Description

Inlet/Outlet Maximum Orifice Range of Set

@20 PSI

Pressure Adjustment

Point

Inlet

MEGR-199-501P 150 1-1/8” 7” WC-2 PSI 1 48,825,000MEGR-199-502P 150 1-1/8” 1-5 PSI 5 55,125,000MEGR-199-503P 150 1-1/8” 2-10 PSI 10 61,425,000MEGR-199-504P 150 1-1/8” 5-15 PSI 15 63,000,000MEGR-199-510P 250 7/8” 7” WC-2 PSI 1 29,295,000MEGR-199-511P 250 7/8” 1-5 PSI 5 33,075,000MEGR-199-512P 250 7/8” 5-15 PSI 15 37,800,000MEGR-199-513P 250 7/8” 2-10 PSI 10 36,225.000MEGR-199-515P 250 7/8” 10-20 PSI 20 40,950,000MEGR-199-903P 250 7/8” 10-65 PSI 30 44,100,000MEGR-199-502PH 300 1-1/8” 1-5 PSI 5 55,125,000MEGR-199-503PH 300 1-1/8” 2-10 PSI 10 61,425,000MEGR-199-504PH 300 1-1/8” 5-15 PSI 15 63,000,000MEGR-199-505PH 300 1-1/8” 10-20 PSI 20 67,725,000MEGR-199-901PH 300 1-1/8” 10-65 PSI 30 74,025,000MEGR-199M-504PH 300 1-1/8” 5-15 PSI 15 42,650,000MEGR-199M-505PH 300 1-1/8” 10-20 PSI 20 67,725,000MEGR-199M-901PH 300 1-1/8” 10-65 PSI 30 74,025,000

REGULATORS REGULATORSLiquid Backpressure Regulator/Relief Valve MARSHALL EXCELSIOR

The MEGR-198H Series Liquid Service Valves are direct-operated relief valves for use on reliefand back pressure applications involving large LP-Gas pumping systems and vaporizers. Internalpressure registration eliminates the need for a control line.

TECHNICAL SPECIFICATIONS: Type: Adjustable/PSI; Max. Inlet Pressure: 250 PSIG; Exterior Finish: Gray powder coat; Regulator Spring: Plated steel; O-ring Seat: Nirile (NBR); Diaphragm: Neoprene; Body Material/Spring Case: Iron

MEGR-198H

The MEGR-1289H Series Relief Valve is available in settings ranging between 1 - 75 PSIG for the 3/4” and 1” models and 7”WC to 15 PSI for the 2” models. This series is a throttling relief valve used downstream of pressure regulators to protect the downstream system from overpressure. A smooth throttling action minimizes pressure surges in the system during emergency operation. This unit features a pilot tube booster to achieve the highest possible relief capacity with a minimum buildup of system pressure.

The MEGR-1289H Series relief valve is installed between large second stage regulators and the burner to provide high capacity relief. They are ideal for low pressure settings due to the increased sensitivity provided by the large diaphragm area and are suitable as a pressure high capacity relief device when installed between a first and second stage regulator.

TECHNICAL SPECIFICATIONS: Type: Adjustable/PSI/WC; Max. Inlet Pressure: 100 PSIG (1” Body), 25 PSIG (2” body); Exterior Finish: Gray powder coat; Diaphragm: Fabric Reinforced Nitrile (NBR); Bonnet/Body Material: 1” - All Aluminum, 2” - Aluminum Bonnet/Iron Body

MEGR-1289 Series

Excela-Flo Vapor Backpressure Regulator/Relief Valves MARSHALL EXCELSIOR

Note: Other configurations and materials available upon request.

Pilot Operated Low Pressure

Regulator

The MEGR-199 Series Industrial Regulators are large capacity, pilot operated, low or high pressure units for use in applications with loads demanding up to 75,000,000 BTU/H capacity.These regulators are best suited for industrial applications where high flow capacity and adownstream monitor control line can be applied. The MEGR-199 series provides exceptional downstream control while operating at very high capacities with minimal droop under varying flow and inlet pressures.

Pilot Operated High Pressure

Regulator

Monitor PilotOperated High

Pressure Regulator

Capacity based on inlet pressures 20 PSIG greater than outlet pressure set point and 20% droop.

2” FNPT

TECHNICAL SPECIFICATIONS: Type: Adjustable/PSI/WC; Max. Inlet Pressure: 150-300 PSIG; Exterior Finish: Gray powder coat; Orifice Material: Stainless Steel; Regulator Spring: Steel; Diaphragm: Steel, Fabric Reinforced Nitrile (NBR); Body Material: Iron; Bonnet Cap & Bonnet: Iron

Excela-Flo Pilot Operated/Industrial Regulators MARSHALL EXCELSIOR

MEGR-199 Series


19 20

A A

Item No. DescriptionMEGR-861 First Stage Regulator Cover for MEGR-291 and MEGR-300 Series RegulatorsMEGR-862 Second Stage Cover for MEGR-253, MEGR-291 & MEGR-300 Series RegulatorsMEGR-900 Z-Mounting Bracket for MEGR-253 and MEGR-291 Series RegulatorsMEGR-RVB L-Mounting Bracket for MEGR-253 Series RegulatorsMEGR-100C Universal Slotted H Style Bracket for Both Full Size and Compact Domestic Regulators

Item No. DescriptionME960-36 MEC Flex-Vent Kit - Fixed Ends - 3 ft.

90° RegulatorVent Assembly

ME900-6

ME960-48 MEC Flex-Vent Kit - Fixed Ends - 4 ft.ME960-72 MEC Flex-Vent Kit - Fixed Ends - 6 ft.ME960-120 MEC Flex-Vent Kit - Universal Outlet (not crimped) - 10 ft.ME960-120C MEC Flex-Vent Kit - Universal Outlet (crimped) - 10 ft.

*Custom lengths available upon request.

REGULATORS

MEGR-900

MEGR-861

MEGR-862

MEGR-RVB

Excela-Flo Regulator Accessories MARSHALL EXCELSIOR

REGULATORS

For more information on Marshall Excelsior productsor installation instructions contact your MTankCo. representative

or go to www.marshallexcelsior.com.

MEGR-100C

Flex-Vent™ Regulator Kit MARSHALL EXCELSIOR

The MEC Flex-Vent™ provides a safe and easy solution to vent LP Gas regulators away from open sources of ignition or other potential fi re hazards. Meets all requirements of the new flexible material allowance in the 2011 NFPA-58, section 5.8.3.1 (3).

FEATURES: • Durable, UV stable flexible PVC hose

material suitable for use with LP Gas vapor• 3/4” NPT swivel inlet for easy installation• Standard 90° vent assembly with screen

• Mounting clamps and coated masonry screws supplied

• Crimped ends for maximum durability• Available in 3, 4, 6 and 10 ft. lengths*

ME960 Series

ME900-6


21 22

A A

Item No. Capacities in BTU\HR

Inlet Outlet Outlet Adj. Range Outlet Pressure

(SCMH) propane PSIG (bar) Setting, PSIG (bar)

984HP - 04 1,000,000 (11.26) 1/4” NPT 1/2” NPT No adjustment 10 (0.69)988HP - 07 2,000,000 (22.51) 1/2” NPT 1/2” NPT 4 - 6 (0.28 - 0.41)988HP - 08 2,000,000 (22.51) POL 3/4” NPT 4 - 6 (0.28 - 0.41) 5 (0.34)988HP - 09 2,250,000 (25.33) POL 3/4” NPT 4 - 6 (0.28 - 0.41)988HP - 04 2,100,000 (23.64) 1/2” NPT 1/2” NPT 8 - 12 (0.55 - 0.83)988HP - 01 2,400,000 (27.01) 3/4” NPT 3/4” NPT 8 - 12 (0.55 - 0.83) 10 (0.69)988HP - 05 2,100,000 (23.64) POL 1/2” NPT 8 - 12 (0.55 - 0.83)988HP - 06 2,250,000 (25.33) POL 3/4” NPT 8 - 12 (0.55 - 0.83)

Item No. Capacities in BTU\HR

Inlet Outlet Outlet Pressure Outlet Pressure

(SCMH) Propane WC (bar) Setting, WC (bar)

988LP - 03 800,000 (9.01)

998LP - 19998LP - 22 1,000,000 (11.26) 1/2”NPT 998LP - 01998LP - 28* 1,400,000 (15.76)998LP - 02998LP - 05 920,000 (10.36) 3/4” NPT LAT998LP - 03 1/2” NPT998LP - 04 1,000,000 (11.26)998LP - 29*998LP - 10

2,300,000 (25.89) 3/4” NPT

998LP - 09 1” NPT 1” NPT

Item No.

Capacities in BTU\HR Inlet Outlet

Outlet Pressure Outlet Pressure (SCMH) Propane WC (bar) Setting, WC (bar)

988LP - 24 800,000 (9.01) 998LP - 39 1/2” NPT 998LP - 40 1,000,000 (11.26) 1/2”NPT 998LP - 41* 998LP - 31 1,400,000 (15.76) 3/4” NPT 998LP - 32

3/4” NPT

998LP - 35 920,000 (10.36) 3/4” NPT LAT 998LP - 33 1/2” NPT 998LP - 42* 1,000,000 (11.26)

3/4” NPT 3/4” NPT 90°

998LP - 34 988TP - 25 700,000 (7.88) 1/2” NPT 1/2” NPT Non-adjustable 998TP - 36 1,680,000 (18.91)

3/4” NPT 3/4” NPT

998TP - 37 1,500,000 (16.88) 3/4” NPT 90° 998TP - 38 1,460,000 (16.43) 1/2” NPT 1/2” NPT

Item No.


Outlet Pressure Outlet Pressure (SCMH) Propane WC (bar) Setting, WC (bar)

988TW - 15 1/2” NPT988TW - 16* 750,000 (8.44) 998TW - 20 1/4” NPT 998TW - 11 998TW - 12*

1,400,000 (15.76) 3/4” NPT

988TW - 28 988TW - 17 988TW - 18*

750,000 (8.44) POL 1/2” NPT

998TW - 21 998TW - 13

1,400,000 (15.76)

3/4” NPT

998TW - 14*

988TW - 27 450,000 (16.43) 1 - 2.2 PSIG

2 PSIG (0.14 bar)

1/4” NPT

3/4” NPT 0.069 - 0.15 bar)

998TW - 23 1,460,000 (16.43) 1 - 2.2 PSIG

2 PSIG (0.14 bar) (0.069 - 0.15 bar)

*Vent-hole in line with the outlet fitting.

REGULATORSREGULATORS

984HP Type

988HP Type

First Stage Regulators CAVAGNA GROUP

The 984HP and 988HP First Stage Regulators reduce the inlet pressure to a medium level tofeed a second stage regulator. The 984HP and 988HP regulators are designed for Type A installations or for installations Type C. They have to be used outdoors in correct mounting position with vent-hole turned downwards. In their standard version, the 984HP regulators are delivered with vent-hole turned in line with the outlet fitting.

TECHNICAL SPECIFICATIONS: Body and Cover: Aluminium; Diaphragm: Reinforced; Supplying Pressure: 25 - 250; Cover Screws: Stainless steel; Inlet Fitting Screws: Stainless steel; Gas Type: Propane; Setting Point: Inlet pressure 100 PSIG, 140,000 BTU, outletpressure 10 PSIG; Provided Flows: Flow based on 25 PSIG (1,725 Bar) inlet pressure and 20% drop (in accordance with UL144 standard)

*Vent-hole in line with the outlet fitting.

11 (27)9 - 13 (22 - 32)988LP Type

998LP Type

Second Stage Regulators CAVAGNA GROUP

The 988LP Series Regulator reduces the pressure coming from a first stage regulator directly tothe inlet pressure of the user appliance or to a medium pressure value in case of installations with pressure governors. These regulators are designed for Type A installations and are to be used outdoors in correct mounting position with vent-hole turned downwards. In the standard version these regulators are delivered with vent-hole in line with the inlet fitting. Three other configurations of the inlet and outlet fittings for the 998 LP model are available:• Back Mount 998 LP-03, 998 LP-04 and 998LP-29• Angle Body 998 LP-05• In line inlet and outlet Flange 998 LP-09 and 998LP-10

3/4” NPT 90°

TECHNICAL SPECIFICATIONS: Body and Cover: Aluminium; Diaphragm: Reinforced; Supplying Pressure: 5 - 15 PSIG; Cover and Inlet Fitting Screws: Stainless steel; Gas Type: Propane; Setting Point: Inlet pressure 10 PSIG, 140,000 BTU, outlet pressure 11 inch WC; Provided Flows: Flow based on 10 PSIG (0.69 bar) inlet pressure and 20% drop (in accordance with UL144 standard)

3/4” NPT

3/4” NPT

3/4” NPT

1/2” NPT

Second Stage Regulators with Incorporated Dielectric Union CAVAGNA GROUP

The Guardian KOSAN+ Regulator incorporates a dielectric insulation and is an all-in-one solution.There is no need to buy separate dielectric unions.

In Accordance with NFPA 58: § 6.9.3.16 Underground metallic piping, tubing, or both that conveyLP-Gas from a gas storage container shall be provided with dielectric fittings at the building to electrically isolate it from the above ground portion of the fixed piping system that enters a building. Such dielectric fitting shall be installed above ground and outdoors.

11 (27)

2 PSIG(0.14 bar)

9 - 13(22 - 32)

1 - 2.2 PSIG(0.069 - 0.15 bar)

TECHNICAL SPECIFICATIONS FOR LP TYPE: Body and Cover: Aluminium; Diaphragm: Reinforced; Supplying Pressure: 5 - 15 PSIG; Cover and Inlet Fitting Screws: Stainless steel; Gas Type: Propane; Setting Point: Inlet pressure 10 PSIG, 140,000 BTU, outlet pressure11 inch WC; Provided Flows: Flow based on 10 PSIG (0.69 bar) inlet pressure and 20% drop (in accordance with UL144 standard)

TECHNICAL SPECIFICATIONS FOR TP TYPE: Body and Cover: Aluminium; Diaphragm: Reinforced; Supplying Pressure: 5 - 15 PSIG; Cover and Inlet Fitting Screws: Stainless steel; Gas Type: Propane; Setting Point: Inlet pressure 10 PSIG, 140,000 BTU, outlet pressure2 PSIG; Provided Flows: Flow based on 10 PSIG (0.69 bar) inlet pressure and 20% drop (in accordance with UL144 standard)

Twin Stage Regulators CAVAGNA GROUP

9 - 13 (22 - 32) 11 (27)

988TW Type

*First and Second Stage spring case vents opposite gauge taps.

998LP Type


23 24

A A

Item No.


Outlet Adjustment Outlet Pressure (SCMH) Propane Range PSIG (bar) Setting, PSIG (bar)

988TP - 22 700,000 (7.88) 1/2” NPT 1/2” NPT998TP - 06 1,680,000 (18.91)

3/4” NPT 3/4” NPT 1 - 2.2

2 (0.14)998TP - 07 1,500,000 (16.88) 3/4” NPT 90° (0.069 - 0.15)

998TP - 08 1,460,000 (16.43) 1/2” NPT 1/2” NPT

Item No.

Capacities in BTU\HR Inlet Outlet (SCMH) Propane

524AS 160,000 (1.80) .880” POL 3/8 NPT

Item No. Capacities in BTU\hr

Inlet Outlet Vent Size

(SCMH) Propane

524AC 600,000 (6.75) 1/2” NPT 3/4” NPT528B 450,000 (5.07) 1/4” Inverted Flare 3/8” NPT 3/8” NPT924N 160,000 (1.80) 3/8” NPT —

REGULATORSREGULATORS

TECHNICAL SPECIFICATIONS: Body and Cover: Aluminium; Diaphragm: Reinforced; Supplying Pressure: 25-250 PSIG; Cover andInlet Fitting Screws: Stainless steel; Gas Type: Propane; Setting Point: Inlet pressure 10 PSIG, 140,000 BTU, Outlet pressure: 11 inchWC; Provided Flows: Flow based on 10 PSIG (0.69 bar) inlet pressure and 20% drop (in accordance with UL144 standard); 988TW Type Dimensions: L 6.692 x W 4.33 x H 4.94; 988TW Type Weight: 39.75 oz.; 998TW Type Dimensions: L 7.055 x W 5.657 x H 4.964;998TW Type Weight: 54.875 oz.

The 998TW Type Double Stage Regulator (Twin Stage) consists of two regulation levels, whichregulates the inlet pressure, coming from the withdrawal cylinder or tank directly to the inlet pressure of the user appliance.

988 TW Type regulators are designed for Type B installation. They are to be used outdoors incorrect mounting position with vent-hole turned downwards.

Twin Stage Regulators (continued) CAVAGNA GROUP

The Double Stage Automatic Changeover Regulator 524 AC is a combination of an automatic changeover working as a first stage coupled to a second stage regulator. The regulator body is made of zinc alloy and it is necessary to use the proper plastic mounting bracket. Please contact your sales representative for additional information.

524 AC TYPE TECHNICAL SPECIFICATIONS: Body and Cover: ZAMAK; Diaphragm: Reinforced;Supplying Pressure: 25 - 250 PSIG; Cover Screws: Stainless steel; Fittings: Brass; Gas: Propane;Setting Point: Inlet pressure 100 PSIG, 140,000 BTU, outlet pressure: 11 WC; Provided Flows:Flow based on 25 PSIG (1.725 bar) inlet pressure and 20% drop (in accordance with UL144 standard); Dimensions: L 9.921 x W 4.212 x H 5.275

528B TYPE TECHNICAL SPECIFICATIONS: Body and Cover: ZAMAK; Diaphragm: Reinforced; Supplying Pressure: 25 - 250 PSIG; Fittings: Brass; Gas: Propane; Setting Point: Inlet pressure 100 PSIG, 140,000 BTU, outlet pressure: 11 WC; Provided Flows: Flow based on 25 PSIG (1.725 bar) inlet pressure and 20% drop (in accordance with UL144 standard); Dimensions:L 7.677 x W 4.212 x H 4.094

924N TYPE TECHNICAL SPECIFICATIONS: Body and Cover: ZAMAK; Supplying Pressure:25 - 250 PSIG; Fittings: Brass; Gas: Propane; Setting Point: Inlet pressure 100 PSIG, 70,000 BTU,outlet pressure: 11 WC; Provided Flows: Flow based on 25 PSIG (1.725 bar) inlet pressureand 20% drop (in accordance with UL144 standard); Dimensions: L 5.314 x W 3.11 x H 3.897

Automatic Changeover Regulators - 524AC Type CAVAGNA GROUP

2-PSIG Regulators CAVAGNA GROUP

988 TP Regulators are designed for Type C of installations. They are to be used outdoors in correct mounting position with vent-hole turned downwards. In the standard version 988 TP regulators are delivered with the vent-hole turned in line with the outlet fitting. There is a special configuration of inlet and outlet fittings for the 998 TP model: • Back Mount 998 LP-07

TECHNICAL SPECIFICATIONS: Body and Cover: Aluminium; Diaphragm: Reinforced; SupplyingPressure: 5 -15 PSIG; Cover and Inlet Fitting Screws: Stainless Steel; Gas Type: Propane; SettingPoint: Inlet Pressure 10 PSIG, 140,000 BTU, Outlet Pressure: 2 PSIG; Provided Flows: Flow based on 10 PSIG (0.69 bar) inlet pressure and 20% drop (in accordance with UL144 standard)

POL Double Stage CAVAGNA GROUP

TECHNICAL SPECIFICATIONS: Type: ASME double stage regulator; Body and Cover Material:ZAMAK; Diaphragm: Reinforced; Supplying Pressure: 25-250 PSIG; Fittings: Brass; Gas: Propane;Setting Point: Inlet pressure 100 PSIG, 70,000 BTU, outlet pressure: 11 WC; Provided Flows: Flow based on 25 PSIG (1.725 bar) inlet pressure and 20% drop (in accordance with UL144 standard); Dimensions: L 5.314 x W 3.11 x H 3.897

998TW Type

524AC Type

528B Type

988TP TypeL 6.692 x W 4.33 x H 4.94

998TP TypeL 7.055 x W 5.657 x H 4.964

524AS Type

924N Type


25 26

A A

Pressure 7.0” PSIG= 1/2 PSIG= 3/4 PSIG= 1 PSIG= Drop 17 mbar 34.5 mbar 52 mbar 69 mbar

Flow Rate 155 220 280 310 CFH (m3/h) (4.3) (6.1) (7.8) (8.7)

Model Outlet 1/2 PSIG= 3/4 PSIG= 1 PSIG= 2 PSIG= 5 PSIG=

Pressure 34.5 mbar 52 mbar 69 mbar 138 mbar 345 mbar

6” WC 160 (4.5) 200 (5.6) 235 (6.6) 285 (8.0) 350 (9.8) 7” WC 155 (4.3) 200 (5.6) 230 (6.4) 280 (7.8) 345 (9.7) 8” WC 155 (4.3) 195 (5.5) 230 (6.4) 270 (7.6) 335 (9.4) 9” WC 145 (4.1) 190 (5.3) 215 (6.0) 260 (7.3) 325 (9.1) 10” WC 135 (3.8) 180 (5.0) 205 (5.7) 245 (6.7) 310 (8.7) 11” WC 125 (3.5) 170 (4.8) 195 (5.5) 235 (6.6) 300 (8.4) 12” WC 125 (3.5) 165 (5.5) 195 (5.5) 230 (6.4) 295 (8.3)

Model Item Pipe Inlet

Setting NG LPG Number Size Pressure

44-1-190-0002 2 PSIG 8” 7” - 11” WC — 44-1-190-0006 2 PSIG 7” — 7” - 11” WC 44-1-190-0008 2 PSIG 11” — 9” - 12” WC 90 44-1-190-0004 1/2” 2 PSIG 11” — 7” - 11” WC 44-1-190-0013 5 PSIG 7” — 7” - 11” WC 44-1-190-0011 5 PSIG 8” 7” - 11” WC — 44-1-190-0012 5 PSIG 11” — 7” - 11” WC

Pressure 7.0” PSIG= 1/2 PSIG= 3/4 PSIG= 1 PSIG= Drop 17 mbar 34.5 mbar 52 mbar 69 mbar

Flow Rate 359 504 627 719 CFH (m3/h) (10.1) (14.3) (17.7) (20.3)

Model Item Pipe Inlet

Setting NG LPG Number Size Pressure

44-1-290-0002 2 PSIG 8” 7” - 11” WC — 44-1-290-0003 2 PSIG 11” — 7” - 11” WC 44-1-290-0010 5 PSIG 8” — 7” - 11” WC 44-1-290-0011 5 PSIG 11” — 7” - 11” WC

Model

Outlet 1/2 PSIG= 3/4 PSIG= 1 PSIG= 2 PSIG= 5 PSIG= Pressure 34.5 mbar 52 mbar 69 mbar 138 mbar 345 mbar

7” WC 364 (10.3) 403 (11.4) 447 (12.7) 517 (14.6) 645 (18.3) 8” WC 359 (10.2) 394 (11.2) 447 (12.7) 509 (14.4) 636 (18.0) 9” WC 342 (9.7) 381 (10.8) 430 (12.2) 500 (14.2) 636 (18.0) 10” WC 329 (9.3) 377 (10.7) 403 (11.4) 496 (14.0) 627 (17.8) 11” WC 302 (8.5) 360 (10.2) 372 (10.5) 473 (13.4) 614 (17.8)

Flow RateCFH (m3/h]

95

95 3/4”

REGULATORSREGULATORSGovernor Regulator - Type 90/2-PSIG - Pressure Drop CAVAGNA GROUP

Pressure Drop - 0.64 sp gr gas expressed in CFH (m3/h)

Governor Regulator - Type 90/2-PSIG - Capacities CAVAGNA GROUP

Capacities based on 1” WC pressure drop from set point 0.64 sp gr gas expressed in CFH (m3/h)

Governor Regulator - Type 90/2-PSIG - Conversion Table CAVAGNA GROUP

The Type 90 OARA Pressure Regulators are manufactured to supply the highest performancesboth as line pressure regulators and as gas appliance regulators. All models are approved by IAS, in accordance with the two different standards.

TECHNICAL SPECIFICATIONS: Rated Inlet Pressure: 2 PSIG (138 mbar); Outlet Pressure Setting: Type 901 7”- 9” WC; Type 902 9”- 12” WC; Type 903 7”- 11” WC; Type 904 7”- 11” WC; Type 905 5”- 9” WC.; Gases: Natural or LP gas; Code: The four digit codeindicates the year and the calendar week, in which the regulator was manufactured; (i.e. 1012: in twelfth week of 2010); AmbientTemp. Range: -40/205° F (-40/96°C); Pipe size NPT: “x“; Venting: Vent limiter “0” 3 - 18-1/8” NPT; Emergency Exposure Limits: 65 PSIG (4.5 BAR) inlet side only; Dimensions: L 4.409 x W 3.956 x H 3.492; Weight: 22.75 oz.

• Precise regulating control of both full flow and of tiny pilot flows

• Fulfills utility specifications for usage in residential, commercial and industrial

applications• All component parts are corrosion-resistant• Diaphragm and washers are made of Nitrile rubber and are resistant to combustible gases

Governor Regulators - Type 95/2-PSIG - Pressure Drop CAVAGNA GROUP

Pressure Drop - 0.64 sp gr gas expressed in CFH (m3/h)

Governor Regulators - Type 95/2-PSIG - Capacities CAVAGNA GROUP

The Type 95 OARA Pressure Regulators are manufactured to supply the highest performancesboth as line pressure regulators and as gas appliance regulators. All models are approved by IAS,in accordance with the two different standards.

Governor Regulators - Type 95/2-PSIG - Conversion Table CAVAGNA GROUP

CAPACITIES based on 1” WC pressure drop from set point 0.64 sp gr gas expressed in CFH (m3/h)

TECHNICAL SPECIFICATIONS: Rated Inlet Pressure: 2 PSIG (138 mbar); Outlet Pressure Setting: Type 951 7”- 11” WC.; Type 952 7”- 11” WC.; Outlet Pressure Setting: Type 951 8” at 200 CFH; Type 952 11” at 200 CFH; Gases: Natural or LP gas; Code: The four digit code indicates the year and the calendar week, in which the regulator was manufactured (i.e. 1012: in twelfth week of 2010); Ambient Temp. Range: -40/205° F (-40/96° C); Pipe Size NPT: “x“ / 1” x 1”; Venting: Vent limiter “0” 6-38 3/8” NPT; Emergency Exposure Limits: 65 PSIG (4.5 BAR) inlet side only; Dimensions: L 5.964 x W 5.551 x H 5.196; Weight: 47.625 oz

Type 90 / 2-PSIG

Type 95 / 2-PSIG

• Rubber works at ambient temperatures of - 40/205° F (-40/96°C)• Rugged die-cast aluminium housings• Regulators have vent limiter type “0” 3 - 18

thread 1/8” NPT which limits gas leakage in case of diaphragm rupture• Manufacturing of the regulators in terms

of balancing capacity guarantees excellent control of the outlet pressure

• Precise regulating control of both full flow and of tiny pilot flows

• Fulfills utility specifications for usage in residential, commercial and industrial

applications• Materials of all component parts are

corrosion-resistant• Diaphragm and washers are made of Nitrile rubber and are resistant to combustible gases

• Rubber is selected to work at the following ambient temperatures: - 40/205° F (-40/96° C)• Rugged die-cast aluminium housing• Brass vent limiter• Regulators have vent limiter type “0”6 - 38

thread 1/8” NPT which limits gas leakage in case of diaphragm rupture• Manufacturing of the regulators in terms

of balancing capacity guarantees excellent control of the outlet pressure

FEATURES:

FEATURES:


27 28

A A

Inlet/Outlet

Outlet Outlet Capacity Item No. Description

Connection Pressure Adjustment

BTU/HR Setting (PSIG) Range (PSIG)

942HP - 03 10 3 - 15 2,600,000 942HP - 04 20 5 - 35 3,600,000 942HP - 05 40 30 - 60 4,200,000 942HP - 07 50 35 - 100 5,250,000 942HP - 08

3/4” NPT 20 5 - 35 5,800,000

942HP - 06 40 30 - 60 6,500,000 948HP - 01 10 3 - 15 2,600,000 948HP - 02 With Internal 15 5 - 20 3,000,000 948HP - 03 Relief Valve 20 5 - 35 3,600,000 948HP - 04 3/4” NPT 20 5 - 35 5,800,000

Item No. Orifice

Inlet/Outlet Outlet Pressure Outlet Pressure Capacity Connection Range (PSIG) Setting BTU/HR

812HP - 03 3/8” 3/4” NPT 6,100,000 812HP - 04 1/2” 3/4” NPT 10,700,000 812HP - 01 1/2” 1” NPT 10,700,000 812HP - 02² 1/2” 1” NPT 10,700,000 811HP - 02³ 1/2” 3/4” NPT 10,700,000 811HP - 01³ 1/2” 1” NPT 10,700,000 818HP - 11¹ 3/8” 3/4” NPT 6,100,000 812HP - 05 1/2” 2” NPT 10,700,000

Outlet

Outlet Capacity Item No.

Description Pressure Adjustment BTU/HR

Setting (PSIG) Range (PSIG)

492HP - 01 15 3 - 20 650,000 492HP - 02 20 3 - 35 750,000 492HP - 03 40 30 - 60 1,200,000 492HP - 04 50 50 - 135 1,000,000 492HP - 05* 20 5 - 35 750,000 493HP - 02 15 3 - 20 650,000 493HP - 01 20 3 - 35 750,000 493HP - 03 40 30 - 60 1,200,000 493HP - 04 50 50 - 135 1,000,000 493HP - 05* 20 5 - 35 750,000 494HP - 02 10 400,000 494HP - 01 15 Non-adjustable 400,000 494HP - 03 20 750,000 495HP - 01 15 5 - 20 650,000 495HP - 02 20 5 - 30 750,000 495HP - 03 40 20 - 50 1,200,000

REGULATORSREGULATORSDirect Operated Regulators - 942HP Type CAVAGNA GROUP

The 94 Series Direct Operated Regulators are designed for high-pressure service and can beused on either on vapor or liquid applications. Outlet pressure ranges from 3 - 100 PSIG. High pressure regulators reduce tank pressure to a lower pressure for use by another regulator. They may also be used for final stage service on specific applications such as high pressure burners orother medium sized commercial industrial applications. It is not equipped with limited relief valve.

Type 9482HP Regulator is an adjustable high pressure regulator with a wide range of outlet pressures. It is equipped with a limited relief valve. Both types are equipped with a ”FNPT” side outlet which is normally plugged and provides an opening for an outlet pressure.

TECHNICAL SPECIFICATIONS: Body and Cover: Aluminum; Diaphragm: Reinforced; Supplying Pressure: 25 - 250 PSIG; Cover Screws:Stainless steel; Gas Type: Propane; Setting Point: Inlet pressure 100 PSIG, 350,000 BTU, outlet pressure 20 PSIG; Provided Flows:Flow based on inlet pressure 20 PSIG (1.38 bar) greater than outlet with 20% drop (in accordance with UL144 standard); Dimensions:L 4.33 x W 4.72 x H 8.26

The 81 Series Direct Operated Regulators are designed for high-pressure service with large loadslike factories, office buildings, etc. They reduce tank pressure to an intermediate pressure foruse by another regulator. They are also used for final stage service on particular application(pounds to pounds). The 81HP series has a wide range of outlet pressures and can be equippedwith a limited relief valve. They have a FNPT side outlet which is normally plugged and providesan opening for an outlet pressure gauge. Type 81 regulators can be equipped with Viton trim.

Direct Operated Regulators - 81HP Type CAVAGNA GROUP

¹ = Has Internal Relief | ² = Fluorocarbon Trim (GLT Viton) | ³ = w/monitoring

5 - 20 PSIG 10 PSIG

TECHNICAL SPECIFICATIONS: Body and Cover: Aluminum; Diaphragm: Reinforced; Supplying Pressure: 25 - 250 PSIG; Cover andInlet Fitting Screws: Stainless steel; Gas Type: Propane; Setting Point: Inlet pressure 100 PSIG, 350,000 BTU, outlet pressure 10PSIG; Provided Flows: Flow based on inlet pressure 20 PSIG (1.38 bar) greater than outlet with 20% drop (in accordance with UL144standard); Dimensions: L 7.67 x W 4.72 x H 9.33

Direct Operated Regulators - 49HP Type CAVAGNA GROUP

Basic Regulator(Handwheel Adjustment)

The 49 Series Direct Operated Regulators are designed for high-pressure service and can beused on either vapor or liquid applications. Their outlet pressure ranges from 3 - 135 PSIG. High pressure regulators usually reduce tank pressure to an intermediate pressure for use by another regulator.

NOTE:• 49 Series Regulators do not have internal relief valves, and can not be installed in fixed piping

serving 0.5 appliance systems.• The 492HP Regulator is an adjustable high pressure regulator with hand wheel adjustment.• The 493HP Regulator is an adjustable high pressure regulator with wrench adjustment and

3 spring ranges from 3 - 100 PSIG.• The 494HP is a fixed high pressure regulator, has no field adjustment, and is very compact.• Type 495HP Regulator is an adjustable high pressure regulator with a dial cap adjustment.

This cap eliminates the need for a gauge on portable applications.

Basic Regulator(Wrench

Adjustment)

Non-adjustable

Dial CapAdjustment

TECHNICAL SPECIFICATIONS: Body and Cover: Aluminum; Diaphragm: Reinforced; Supplying Pressure: 25 - 250 PSIG; Cover Screws:Stainless steel; Gas Type: Propane; Setting Point: Inlet pressure 100 PSIG, 200,000 BTU, outlet pressure 20 PSIG; Provided Flows: Flow based on inlet pressure 20 PSIG (1.38 Bar) greater than outlet with 20% drop (in accordance with UL144 standard); Dimensions:L 2.56 x W 2.89 x H 4.88

*Inlet M POL

Basic Regulator

1/2” NPT

1/2” NPT

For more information on Cavagna Group productsor installation instructions contact your MTankCo. representative

or go to www.cavagnagroup.com.

942HP Type

81HP Type

Type 492

Type 495

Type 494

Type 493


29 30

A A

* NOTE: Dielectric option available. Add “D” after the prefix part number i.e. ME1662D-12

1/4” Tube OD Item Number Short Nipple

3/8” Tube OD Short Nipple

90º 90º 270° Right 360°

Male Hard Nose POL x Male Hard Nose POL, 12 — ME1680-12B90 ME1680-12B270R ME1680-12B360 7/8” Nut 1/4” MNPT x Male Hard 5 ME1669-5B90 ME1689-5B90 — — Nose POL, 7/8” Nut 6 ME1669-6B90 ME1689-6B90 — —

Approx.Length

Description XItem No.

1/4” Tube OD 3/8” Tube ODLong Nipple Short Nipple Long Nipple Short Nipple

Male Hard Nose POL xMale Hard Nose POL,

7/8” Nut

6 — X X X12 ME1662-12* X X X20 ME1662-20* ME1664-20* ME1680L-20* ME1680-20*30 ME1662-30 ME1664-30 ME1680L-30 ME1680-3036 ME1662-36 ME1664-36 ME1680L-36 ME1680-3648 ME1662-48 ME1664-48 ME1680L-48 ME1680-48

Male Hard Nose POL xMale Hard Nose POL,

1-1/8” Nut

20 ME1660-20 — — ME1680HD-2030 ME1660-30 — — —36 ME1660-36 — — —48 ME1660-48 — — —

1/4” Male Inverted Flare x

Male Hard Nose POL,7/8” Nut

15 — ME1665-15 — —20 ME1663-20 ME1665-20 — —30 ME1663-30 ME1665-30 — —36 ME1663-36 ME1665-36 — —48 ME1663-48 ME1665-48 — —

1/4” Male Inverted Flare x

Male Hard Nose POL,1-1/8” Nut

20 ME1661-20 — — —30 ME1661-30 — — —36 ME1661-36 — — —40 ME1661-40 — — —48 ME1661-48 — — —

1/4” MNPT xMale Hard Nose POL,

7/8” Nut

6 ME1679-06 ME1669-06 — ME1689-0612 ME1679-12* ME1669-12* ME1689L-12 ME1689-1218 ME1679-18 ME1669-18* — —20 ME1679-20* ME1669-20 ME1689L-20 ME1689-2030 ME1679-30 ME1669-30 ME1689L-30 ME1689-3036 ME1679-36 ME1669-36 — ME1689-3648 ME1679-48 ME1669-48 — ME1689-48

1/4” MNPT x Male Hard Nose POL, 1-1/8” Nut

20 ME1679HD-20 — — —48 ME1679HD-48 — — —

1/2” MNPT x Male Hard Nose POL, 7/8” Nut

12 — — ME1684L-12 ME1684-1220 — — ME1684L-20 ME1684-20

Pigtail and Hogtail Assemblies come with two brass connectors brazed onto a heavy wallannealed copper tube with a 250 PSIG pressure rating. The 1/4” has a pull test rating of 500 andthe 3/8” tube has a pull test rating of 750 pounds. Listed and tested in accordance with UL 569.

Different applications require specific pigtail and hogtail assemblies. Special attention is requiredwhen ordering to ensure the proper assembly is purchased for the intended application. Marshall Excelsior recommends every new installation or replacement regulator have a new pigtail installed.

*ME1600D Series Dielectric Pigtails/Hogtails are intended to isolate metallic piping from sourcesof electrical current and to help prevent galvanic corrosion when used on underground containers.The ME1600D dielectric pigtail/hogtail would typically be installed at the ASME tank directly upstream of the first stage regulator prior to underground piping, isolating the underground metallic piping from electric current.

Copper Pigtails and Hogtails MARSHALL EXCELSIOR

PIGTAILS & HOGTAILS PIGTAILS & HOGTAILSBent Copper Pigtails and Hogtails MARSHALL EXCELSIOR

Long Nipple

Short Nipple

1/4” Inverted Flare

1/4” MNPT

Male Hard Nose POL, 7/8” Nut

Dielectric Version

90° Bend

270° Bend Right Hand


31 32

B B

INTERNAL VALVES INTERNAL VALVES

• To order Kalrez® add “K” for Kalrez® after the prefix part number i.e. ME990K-10-35• To order Neoprene add “N” for Neoprene after the prefix part number i.e. ME990N-10-35• To order Viton® add “V” for Viton® after the prefix part number i.e. ME990V-10-35• Viton® and Kalrez® are trademarks of DuPont Performance Elastomers.NOTE: Indicate desired excess flow closing value when ordering - see chart for values i.e. ME990-10-85

(85 GPM)

Marshall Excelsior 1-1/4” Threaded Internal Valves are intended for use on bobtail trucks and storage tanks with 1-1/4” threaded connections in directional or bidirectional flow applications.Provides both manual shut-down and excess flow, closing in the event of the piping being separated from the valve. May be equipped with manual latch, pneumatic or rotary actuator, open/closing devices. Valves are equipped with a break-away feature in the cast body which permits the piping to shear off in the event of side impact, leaving the valve poppet intact and protecting the tank from catastrophic product loss. For liquid or vapor service applications.

FEATURES: • Standardized 316 stainless steel cast body

for maximum durability and corrosion resistence

• All stainless internal component construction• Hexagonal installation flats to fit standard

2-3/8” hex socket wrench• Precision machined hard coated stem• Fully retained Nitrile seat disc• Large variety of excess flow closing values

• Roller cam actuation• Industry’s fastest bleed time• Removable data plate• Industry’s easiest valve to service• Standard construction utilizes Nitrile seals• Available with Neoprene, Viton®, or Kalrez®

seals• UL Listed for LPG and NH3 service• RulonTM bearing on stub shaft

1-1/4” Threaded Internal Valve MARSHALL EXCELSIOR

ME990-10 Series

• To order Kalrez® add “K” for Kalrez® after the prefix part number i.e. ME992K-10-35• To order Neoprene add “N” for Neoprene after

the prefix part number i.e. ME992N-10-35• To order Viton® add “V” for Viton® after the

prefix part number i.e. ME992V-10-35• Viton® and Kalrez® are trademarks of DuPont Performance Elastomers.NOTE: Indicate desired excess flow closing

value when ordering - see chart for values i.e. ME992-10-85 (85 GPM)

The 1-1/4” Threaded Tee Body Internal Valve is intended for use on bobtail trucks and storagetanks with 1-1/4” threaded connections in directional or bi-directional flow applications. Providesboth manual shut-down as well as excess flow closing in the event of the piping being separatedfrom the valve. Can be equipped with manual latch, pneumatic or rotary actuator, open/ closingdevices. All valve models are equipped with a break-away feature in the cast body which permitsthe piping to shear off in the event of side impact, leaving the valve poppet intact and protectingthe tank from catastrophic product loss. The tee body features an additional FNPT side dischargeport. For liquid or vapor service applications.

FEATURES: • Standardized 316 stainless steel cast body

for maximum durability and corrosion resistence• All stainless internal component construction• Precision machined hard coated stem• Fully retained Nitrile seat disc• Largest variety of excess flow closing values• Roller cam actuation

• Industry’s fastest bleed time• Removable data plate• Industry’s easiest valve to service• Standard construction utilizes Nitrile seals• Available with Neoprene, Viton®, or Kalrez® seals• UL LISTED for LPG & NH3 service• Rulon™ bearings on stem and stub shafts

For NH3 Multiply GPM by .90

1-1/4” Threaded Tee Body Internal Valves MARSHALL EXCELSIOR

ME992-10

1-1/4” NTP Tee BodyInternal Valve

w/ Manual Latch

Item No. DescriptionME992-10-”X” ExceleratorTM 1-1/4” MNPT x 1-1/4” FNPT Internal Valve - OnlyME992A-10-”X” ExceleratorTM 1-1/4” MNPT x 1-1/4” FNPT Internal Valve - with Pnuematic Actuator

ME992AR-10-”X” ExceleratorTM 1-1/4” MNPT x 1-1/4” FNPT Internal Valve - with Rotary Actuator

ME992M-10-”X” ExceleratorTM 1-1/4” MNPT x 1-1/4” FNPT Internal Valve - with Manual Latch

“X” 1-1/4” Valve Liquid Closing Flow Values35 35 GPM LPG Closing Flow55 55 GPM LPG Closing Flow

85 85 GPM LPG Closing Flow

Item No. DescriptionME990-10-”X” ExceleratorTM 1-1/4” MNPT x 1-1/4” FNPT Internal Valve - OnlyME990A-10-”X” ExceleratorTM 1-1/4” MNPT x 1-1/4” FNPT Internal Valve - with Pnuematic Actuator







33 34

B B


ME991-10-”X” ExceleratorTM 1-1/4” NPT x 4 Bolt Flange Internal Valve - Only

ME991A-10-”X” ExceleratorTM 1-1/4” NPT x 4 Bolt Flange Internal Valve - with Pneumatic Actuator

ME991AR-10-”X” ExceleratorTM 1-1/4” NPT x 4 Bolt Flange Internal Valve - with Rotary Actuator

ME991M-10-”X” ExceleratorTM 1-1/4” NPT x 4 Bolt Flange Internal Valve - with Manual Latch

“X” 1-1/4” Valve Liquid Closing Flow Values

35 35 GPM LPG Closing Flow55 55 GPM LPG Closing Flow


INTERNAL VALVES1-1/4” MNPT x 4 Bolt Flange MARSHALL EXCELSIOR

• To order Kalrez® add “K” for Kalrez® after the prefix part number i.e. ME991K-10-35

• To order Neoprene add “N” for Neoprene after the prefix part number i.e. ME991N-10-35

• To order Viton® add “V” for Viton® after the prefix part number i.e. ME991V-10-35

• Viton® and Kalrez® are trademarks of DuPont Performance Elastomers.

NOTE: Indicate desired excess flow closing value when ordering - see chart for values i.e.

ME991-10-85 (85 GPM)

The ME991-10 Series Valves feature the new modular Excel-Flange 4 bolt outlet flange design that can be easily adapted to both NTP thread or socket weld companion flanges (ME842 and ME843 series) ranging from 1-1/4” to 2” in diameter making it universal to piping sizes withinthis range. This innovative system allows installers the ability to eliminate unnecessaryconnections as well as possible leak points by integrating a convenient 4 bolt flange union at the valve outlet. Intended for use on bobtail trucks and storage tanks with 1-1/4” threaded connections in directional or bi-directional flow applications. Provides both manual shut-down as well as excess flow closing in the event of the piping being separated from the valve. Can be equipped with manual latch, pneumatic or rotary actuator, and open/closing devices. All valve models are equipped with a break-away feature in the cast body which permits the pipingto shear off in the event of side impact, leaving the valve poppet intact and protecting the tankfrom catastrophic product loss. For liquid or vapor service applications.

• Durable 316 stainless steel body• All stainless internal component construction• Precision machined hard coated• Fully retained Nitrile seat disc• Largest variety of excess flow closing values• Roller cam actuation• Industry’s fastest bleed time• Removable data plate

• Industry’s easiest valve to service• Standard construction utilizes Nitrile seals• Available with Neoprene, Viton®, or Kalrez® seals• UL Listed for LPG and NH3 service• RulonTM bearings on stem and stub shafts• 4 Bolt universal outlet flange for built in

union joint

FEATURES:


ME991-10 Series

INTERNAL VALVES

Item No. DescriptionME992-12-”X” ExceleratorTM 1-1/2” MNPT x 1-1/2” FNPT Internal Valve - OnlyME992A-12-”X” ExceleratorTM 1-1/2” MNPT x 1-1/2” FNPT Internal Valve - with Pneumatic Actuator



1-1/2” Threaded Tee Body Internal Valves MARSHALL EXCELSIOR




120 120 GPM LPG Closing FlowME992-12 SERIES

1-1/2” NTP Tee BodyInternal Valve





NOTE: Indicate desired excess flow closing value when ordering - see chart for values i.e. ME992-12-85 (85 GPM)

The 1-1/2” Threaded Tee Body Internal Valve is intended for use on bobtail trucks, storage tanksand nurse wagons with 1-1/2” threaded connections in directional or bi-directional flowapplications. Provides both manual shut-down as well as excess flow closing in the event of the piping being seperated from the valve. Can be equipped with manual latch, pneumatic orrotary actuator, open/closing devices. All valve models are equipped with a break-away featurein the cast body which permits the piping to shear off in the event of side impact, leaving thevalve poppet intact and protecting the tank from catastrophic product loss. The tee body featuresan additional FNPT side discharge port. FOR LIQUID OR VAPOR SERVICE APPLICATIONS.

FEATURES: • Durable ductile iron body• All stainless internal component construction• Precision machined hard coated stem• Fully retained Nitrile seat disc• Largest variety of excess flow closing values• Roller cam actuation• Industry’s fastest bleed time• Removable data plate

• Industry’s easiest valve to service• Standard construction utilizes Nitrile seals• Available with Neoprene, Viton®, or Kalrez® seals• UL LISTED for LPG & NH3 service• Rulon™ bearings on stem and stub shafts• Supplied with hex socket 1-1/2” port plug

for single discharge applications



35 36

B B

Item No. Description Weight (lbs.)ME994S-2F-16-”X” ExceleratorTM 2”-300 lb. Modifi ed Single Flange x 2”- 8 Bolt Flange Internal Valve - Only 21.6

ME994SA-2F-16-”X” ExceleratorTM 2”-300 lb. Modifi ed Single Flange x 2”- 8 Bolt Flange Internal Valve - with Pneumatic Actuator 35.5

ME994SAR-2F-16-”X” ExceleratorTM 2”-300 lb. Modifi ed Single Flange x 2”- 8 Bolt Flange Internal Valve - with Rotary Actuator 28.9

Excela-Flange 2”- 300 LB X 2” - 8 Bolt Companion Flange MARSHALL EXCELSIOR

“X” 2” Valve Liquid Closing Flow Values110 110 GPM LPG Closing Flow160 160 GPM LPG Closing Flow


• To order Kalrez® add “K” for Kalrez® after the prefix part number i.e. ME994SK-2F-16-260

• To order Neoprene add “N” for Neoprene after the prefix part number i.e. ME994SN-2F-16-260

• To order Viton® add “V” for Viton® after the prefix part number i.e. ME994SV-2F-16-260


NOTE: Indicate desired excess flow closing value when ordering - see chart for values i.e. ME994S-2F-16-260 (260 GPM)

The ME994S-2F Series Valves feature our new modular Excela-FlangeTM 2”- 8 bolt outlet flange design that can be easily adapted to either 2” NPT or socket weld companion flanges (MEP994S-2F-2SW) making it universal to either piping construction.

FEATURES: • Durable steel body with cadmium surface

plating• Universal 2”- 8 bolt outlet flange connection

for threaded or welded piping• Universal 2” - 8 bolt outlet flange provides

a built-in union joint for easy servicability• All stainless internal component construction• One piece threaded packing gland• Precision machined hard coated stem and

stem guide• Fully retained nitrile seat disc• Largest variety of excess flow closing values• Corrosion resistant sleeved flange bolt holes• Xylan coated corrosion resistant

mounting studs

• Roller cam actuation• Industry’s fastest bleed time• Removable data plate• Industry’s easiest valve to service• Standard construction utilizes nitrile seals• Available with Neoprene, Viton®, or

Kalrez® seals• UL Listed for LPG and NH3 service• RulonTM bearings on stem and stub shafts• RulonTM bearings on stem and stub shafts• Fits standard 2” - 300# flanged tank

openings


ME994S-2F-16 Series







Item No. DescriptionME990S-2F-16-”X” ExceleratorTM 2”- 300 lb. Modified Single Flange x 2” FNPT Internal Valve - OnlyME990SA-2F-16-”X” ExceleratorTM 2”- 300 lb. Modified Single Flange x 2” FNPT Internal Valve - with Pneumatic Actuator

ME990SAR-2F-16-”X” ExceleratorTM 2”- 300 lb. Modified Single Flange x 2” FNPT Internal Valve - with Rotary Actuator

ME990S-2DFM-”X” ExceleratorTM 2”- 300 lb. Modified Double Flange Internal Valve - Only

ME990SA-2DFM-”X” ExceleratorTM 2”- 300 lb. Modified Double Flange Internal Valve - with Pneumatic Actuator

ME990SAR-2DFM-”X” ExceleratorTM 2”- 300 lb. Modified Double Flange Internal Valve - with Rotary Actuator

2” X 300 LB - Single and Double Flanged Internal Valve MARSHALL EXCELSIOR



The ME990S Series Valves are intended for use on bobtail delivery trucks, transport trucks and large storage tanks with 2” flanged connections in directional or bi-directional flow applications. Provides both manual shut-down and excess flow closing in the event of the piping being separated from the valve. Can be equipped with manual latch, pneumatic or rotary actuator open/closing devices. All valve models are equipped with a break-away feature in the cast body which permits the pump or piping to shear off in the event of side impact, leaving the valve poppet intact and protecting the tank from catastrophic product loss.

FEATURES: • All stainless internal component construction• One piece threaded packing gland• Precision machined hard coated stem and

stem guide• Fully retained Nitrile seat disc• Largest variety of excess flow closing

values• Corrosion resistant sleeved flange bolt

holes• Xylan coated corrosion resistant

mounting studs

• Roller cam actuation• Industry’s fastest bleed time• Removable data plate• Industry’s easiest valve to service• Standard construction utilizes Nitrile seals• Available with Neoprene, Viton®, or

Kalrez® seals• Available with 316 Stainless Steel bodies• UL Listed for LPG & NH3 service• RulonTM bearings on stem and stub shafts


ME990S-2F-16 Series2”- 300 lb. x 2” FNPT

ME990S-2DFM Series2”-300 lb. Double

Flanged Internal Valve


37 38

B B

INTERNAL VALVES INTERNAL VALVES2” and 3” Threaded Internal Valve MARSHALL EXCELSIOR

Marshall Excelsior’s 2” and 3” Threaded Internal Valves are intended for use on transport trucksand large storage tanks with 2” or 3” threaded connections in directional or bidirectional flowapplications. Provides both manual shut-down and excess flow closing in the event of the pipingbeing separated from the valve. Can be equipped with manual latch, pneumatic or rotary actuatoropen/closing devices. All valve models are equipped with a break-away feature in the cast bodywhich permits the piping to shear off in the event of side impact, leaving the valve poppet intactand protecting the tank from catastrophic product loss. For liquid or vapor service applications.

FEATURES: • Durable ductile body with cadmium surface plating• All stainless internal component construction• One piece threaded packing gland• Precision machined hard coated stem• Fully retained Nitrile seat disc• Largest variety of excess flow closing values• Roller cam actuation

• Industry’s fastest bleed time• Removable data plate• Industry’s easiest valve to service• Standard construction utilizes Nitrile seals• Available with Neoprene, Viton®, or Kalrez® seals• UL listed for LPG and NH3 service• RulonTM bearings on stem and stub shafts






ME990-24-250 (250 GPM)

ME990M-16 Series

ME990-24 Series

Item No. DescriptionME990-16-”X” ExceleratorTM 2” MNPT x 2” FNPT Internal Valve - OnlyME990A-16-”X” ExceleratorTM 2” MNPT x 2” FNPT Internal Valve - with Pnuematic Actuator

ME990AR-16-”X” ExceleratorTM 2” MNPT x 2” FNPT Internal Valve - with Rotary Actuator

ME990M-16-”X” ExceleratorTM 2” MNPT x 2” FNPT Internal Valve - with Manual LatchME990-24-”X” ExceleratorTM 3” MNPT x 3” FNPT Internal Valve - OnlyME990A-24-”X” ExceleratorTM 3” MNPT x 3” FNPT Internal Valve - with Pnuematic ActuatorME990AR-24-”X” ExceleratorTM 3” MNPT x 3” FNPT Internal Valve - with Rotary ActuatorME990M-24-”X” ExceleratorTM 3” MNPT x 3” FNPT Internal Valve - with Manual Latch










ME992M-16

2” NTP Tee BodyInternal Valve

w/ Manual Latch

ME992M-24

3” NTP Tee BodyInternal Valve

w/Manual Latch

The 2” and 3” Threaded Tee Body Internal Valves are intended for use on transport trucks and large storage tanks with 2” or 3” threaded connections in directional or bidirectional flowapplications. They provide manual shut-down and excess flow closing should a pipe separate fromthe valve. A manual latch, pneumatic or rotary actuator open/closing devices are available. All valve models have a break-away feature in the cast body allowing the piping to shear off in the event of side impact, leaving the valve poppet intact. The tee body features an additional FNPT side discharge port. Valves are for liquid or vapor service applications.

FEATURES: • Ductile body with cadmium surface plating• All stainless internal component construction• One piece threaded packing gland• Precision machined hard coated stem• Fully retained Nitrile seat disc• Largest variety of excess flow closing values• Roller cam actuation

• Industry’s fastest bleed time• Removable data plate• Industry’s easiest valve to service• Standard construction utilizes Nitrile seals• Available with Neoprene, Viton®, or Kalrez® seals

• To order Kalrez® add “K” for Kalrez® after the prefix part number i.e. ME992K-16-160• To order Neoprene add “N” for Neoprene after

the prefix part number i.e. ME992N-16-160• To order Viton® add “V” for Viton® after the

prefix part number i.e. ME992V-16-160• Viton® and Kalrez® are trademarks of DuPont Performance Elastomers.NOTE: Indicate desired excess flow closing

value when ordering - see chart for values i.e. ME992-24-250 (250 GPM)

For NH3 Multiply GPM by .90Side discharge increases differential to close byapproximately 2 PSIG

2” and 3” Threaded Tee Body Internal Valves MARSHALL EXCELSIOR

Item No. DescriptionME992-16-”X” ExceleratorTM 2” MNPT x 2” FNPT Tee Body Internal Valve - OnlyME992A-16-”X” ExceleratorTM 2” MNPT x 2” FNPT Tee Body Internal Valve - with Pnuematic Actuator

ME992AR-16-”X” ExceleratorTM 2” MNPT x 2” FNPT Tee Body Internal Valve - with Rotary Actuator

ME992M-16-”X” ExceleratorTM 2” MNPT x 2” FNPT Tee Body Internal Valve - with Manual LatchME992-24-”X” ExceleratorTM 3” MNPT x 3” FNPT Tee Body Internal Valve - OnlyME992A-24-”X” ExceleratorTM 3” MNPT x 3” FNPT Tee Body Internal Valve - with Pnuematic ActuatorME992AR-24-”X” ExceleratorTM 3” MNPT x 3” FNPT Tee Body Internal Valve - with Rotary ActuatorME992M-24-”X” ExceleratorTM 3” MNPT x 3” FNPT Tee Body Internal Valve - with Manual Latch









39 40

B “X” 3” Valve Liquid Closing Flow Values

175 175 GPM LPG Closing Flow 250 250 GPM LPG Closing Flow 300 300 GPM LPG Closing Flow 375 375 GPM LPG Closing Flow 475 475 GPM LPG Closing Flow 500 500 GPM LPG Closing Flow


ME991-16-”X” ExceleratorTM 2” MNPT x 2” 300# Flange Internal Valve - OnlyME991A-16-”X” ExceleratorTM 2” MNPT x 2” 300# Flange Internal Valve - with Pnuematic ActuatorME991AR-16-”X” ExceleratorTM 2” MNPT x 2” 300# Flange Internal Valve - with Rotary ActuatorME991M-16-”X” ExceleratorTM 2” MNPT x 2” 300# Flange Internal Valve - with Manual LatchME991-24-”X” ExceleratorTM 3” MNPT x 3” 300# Flange Internal Valve - OnlyME991A-24-”X” ExceleratorTM 3” MNPT x 3” 300# Flange Internal Valve - with Pnuematic ActuatorME991AR-24-”X” ExceleratorTM 3” MNPT x 3” 300# Flange Internal Valve - with Rotary ActuatorME991M-24-”X” ExceleratorTM 3” MNPT x 3” 300# Flange Internal Valve - with Manual Latch

“X” 2” Valve Liquid Closing Flow Values

110 110 GPM LPG Closing Flow 160 160 GPM LPG Closing Flow 260 260 GPM LPG Closing Flow

B

INTERNAL VALVES

Marshall Excelsior’s 2” and 3” Flanged Internal Valves are intended for use on transport trucksand large storage tanks with 2” or 3” threaded connections in directional or bi-directional flowapplications. The ME991-16 and ME991-24 Series feature standard 300# outlet flanges for fastreliable piping connections downstream of the tank. Ideally suited for existing tanks with NPT threaded couplings but downstream welded piping is desirable. Provides both manual shut-downand excess flow closing in the event of the piping being separated from the valve. Can be equipped with manual latch, pneumatic or rotary actuator open/closing devices. All valve modelsare equipped with a break-away feature in the cast body which permits the piping to shear offin the event of side impact, leaving the valve poppet intact and protecting the tank fromcatastrophic product loss. For liquid or vapor service applications.

2” and 3” MNPT x 300 LB Flanged Internal Valve MARSHALL EXCELSIOR

FEATURES: • Durable ductile body with cadmium surface plating• All stainless internal component construction• One piece threaded packing gland• Precision machined hard coated stem• Fully retained Nitrile seat disc• Largest variety of excess flow closing values• Roller cam actuation• Industry’s fastest bleed time

• Removable data plate• Industry’s easiest valve to service• Standard construction utilizes Nitrile seals• Available with Neoprene, Viton®, or Kalrez® seals• UL Listed for LPG and NH3 service• RulonTM bearings on stem and stub shafts• Xylan coated corrosion resistant mounting

studs and gaskets included






ME991-24-250 (250 GPM)

ME991-16

ME991-24

INTERNAL VALVES






Item No. DescriptionME992S-2F-16-”X” ExceleratorTM 2”- 300 lb. Modified Single Flange x 2” FNPT Tee Body Internal Valve - OnlyME992SA-2F-16-”X” ExceleratorTM 2”- 300 lb. Modified Single Flange x 2” FNPT Tee Body Internal Valve - with Pneumatic Actuator

ME992SAR-2F-16-”X” ExceleratorTM 2”- 300 lb. Modified Single Flange x 2” FNPT Tee Body Internal Valve - with Rotary Actuator

ME992S-3F-24-”X” ExceleratorTM 3”- 300 lb. Modified Single Flange x 3” FNPT Tee Body Internal Valve - Only

ME992SA-3F-24-”X” ExceleratorTM 3”- 300 lb. Modified Single Flange x 3” FNPT Tee Body Internal Valve - with Pneumatic Actuator

ME992SAR-3F-24-”X” ExceleratorTM 3”- 300 lb. Modified Single Flange x 3” FNPT Tee Body Internal Valve - with Rotary Actuator

2” & 3”- Flanged Tee Body Internal Valve Series MARSHALL EXCELSIOR









These 2” and 3” Flanged Tee Body Internal Valves are intended for use on bobtail deliverytrucks, transport trucks and large storage tanks with 2” and 3” flanged connections in directionalor bi-directional flow applications. Provides both manual shut-down and excess flow closingin the event of the piping being separated from the valve. Can be equipped with manual latch,pneumatic or rotary actuat or open/closing devices. All valve models are equipped with a break-away feature in the cast body which permits the pump or piping to shear off in the event of sideimpact, leaving the valve poppet intact and protecting the tank from catastrophic product loss.The tee body features an additional FNPT side discharge port for liquid service applications.


plating• All stainless internal component construction• One piece threaded packing gland• Precision machined hard coated stem and

stem guide• Fully retained Nitrile seat disc• Largest variety of excess flow closing values• Corrosion resistant sleeved flange bolt holes• Xylan coated corrosion resistant mounting

studs



ME992S-2F-16

ME992S-3F-24



41 42

B B


• To order Kalrez® add “K” for Kalrez® after the prefix part number i.e. ME993SK-24-250

• To order Neoprene add “N” for Neoprene after the prefix part number i.e. ME993SN-24-250

• To order Viton® add “V” for Viton® after the prefix part number i.e. ME993SV-24-250


NOTE: Indicate desired excess flow closing value when ordering - see chart for values i.e. ME993S-24-250 (250 GPM)

Item No. DescriptionME993S-16-”X” ExceleratorTM 2”- 300 lb. Modified Single Flange x (2) 2”-300 lb. Tee Body Internal Valve - OnlyME993SA-16-”X” ExceleratorTM 2”- 300 lb. Modified Single Flange x (2) 2”-300 lb. Tee Body Internal Valve - with Pneumatic Actuator

ME993SAR-16-”X” ExceleratorTM 2”- 300 lb. Modified Single Flange x (2) 2”-300 lb. Tee Body Internal Valve - with Rotary Actuator

ME993S-24-”X” ExceleratorTM 2”- 300 lb. Modified Single Flange x (2) 3”-300 lb. Tee Body Internal Valve - Only

ME993SA-24-”X” ExceleratorTM 2”- 300 lb. Modified Single Flange x (2) 3”-300 lb. Tee Body Internal Valve - with Pneumatic Actuator

ME993SAR-24-”X” ExceleratorTM 2”- 300 lb. Modified Single Flange x (2) 3”-300 lb. Tee Body Internal Valve - with Rotary Actuator

2” & 3”- 300 LB 3-Way Flanged Tee Body Series MARSHALL EXCELSIOR



ME990S-3DF Series

Marshall Excelsior’s 2” & 3” 300 LB 3-Way Flanged Tee Body Valves are inntended for use on bobtail delivery trucks, transport trucks and large storage tanks with 2” and 3” flangedconnections in directional or bi-directional flow applications. Provides both manual shut-down and excess flow closing in the event of the piping being separated from the valve. Can be equipped with manual latch, pneumatic or rotary actuator open/closing devices. All valve models are equipped with a break-away feature in the cast body which permits the pump orpiping to shear off in the event of side impact, leaving the valve poppet intact and protecting the tank from catastrophic product loss. The flanged tee body features an additional 300 lb. flanged side discharge port for liquid service applications.



stem guide• Fully retained Nitrile seat disc• Largest variety of excess flow closing values• Corrosion resistant sleeved flange bolt holes• Xylan coated corrosion resistant mounting

studs




ME993S-16 SERIES

“X” 3” Valve Liquid Closing Flow Values

175 175 GPM LPG Closing Flow250 250 GPM LPG Closing Flow





ME990S-3F-24 Series

• To order Kalrez® add “K” for Kalrez® after the prefix part number i.e. ME990SK-SDF-300

• To order Neoprene add “N” for Neoprene after the prefix part number i.e. ME990SN-SDF-300

• To order Viton® add “V” for Viton® after the prefix part number i.e. ME990SV-SDF-300



ME990S-3SF-250 (250 GPM)

These 3” Flanged Internal Valves are intended for use on bobtail delivery trucks, transport trucks and large storage tanks with 3” flanged connections in directional or bidirectional flow applications. Provides both manual shut-down and excess flow closing in the event of the pipingbeing separated from the valve. Can be equipped with manual latch, pneumatic or rotary actuator open/closing devices. All valve models are equipped with a break-away feature in the cast body which permits the pump or piping to shear off in the event of side impact, leaving the valve poppet intact and protecting the tank from catastrophic product loss.

• Durable steel body with cadmium surface plating• All stainless internal component construction• One piece threaded packing gland• Precision machined hard coated stem and

stem guide• Fully retained Nitrile seat disc• Largest variety of excess flow closing values• Corrosion resistant sleeved flange bolt holes• Xylan coated corrosion resistant mounting studs

• Roller cam actuation• Industry’s fastest bleed time• Removable data plate• Industry’s easiest valve to service• Standard construction utilizes Nitrile seals• Available with Neoprene, Viton®, or Kalrez® seals• Available with 316 Stainless Steel bodies• UL Listed for LPG and NH3 service• RulonTM bearings on stem and stub shafts

FEATURES:

3” Flanged Internal Valve MARSHALL EXCELSIOR







Item No. DescriptionME990S-3DF -”X” ExceleratorTM 3”- Double Flange Bobtail Internal Valve - OnlyME990SA-3DF -”X” ExceleratorTM 3”- Double Flange Bobtail Internal Valve - with Pneumatic Actuator

ME990SAR-3DF -”X” ExceleratorTM 3”- Double Flange Bobtail Internal Valve - with Rotary Actuator

ME990S-3DFM-”X” ExceleratorTM 3”- 300 lb. Modified Double Flange Internal Valve - Only

ME990SA-3DFM-”X” ExceleratorTM 3”- 300 lb. Modified Double Flange Internal Valve - with Pneumatic Actuator

ME990SAR-3DFM-”X” ExceleratorTM 3”- 300 lb. Modified Double Flange Internal Valve - with Rotary Actuator

ME990S-3F -24-”X” ExceleratorTM 3”- 300 lb. Modified Single Flange x 3” FNPT Internal Valve - Only

ME990SA-3F -24-”X” ExceleratorTM 3”- 300 lb. Modified Single Flange x 3” FNPT Internal Valve - with Pneumatic Actuator

ME990SAR-3F -24-”X” ExceleratorTM 3”- 300 lb. Modified Single Flange x 3” FNPT Internal Valve - with Rotary Actuator


ME990S-3DF Series


43 44

B B

INTERNAL VALVES

• To order Kalrez® add “K” for Kalrez® after the prefix part number i.e. ME990K-3F-500

• To order Neoprene add “N” for Neoprene after the prefix part number i.e. ME990N-3F-500

• To order Viton® add “V” for Viton® after the prefix part number i.e. ME990V-3F-500


NOTE: Indicate desired excess flow closing value when ordering - see chart for values i.e. ME990-3F-500 (650 GPM)

Item No. DescriptionME990-3F-”X” ExceleratorTM 3” Single Flange Internal Valve - OnlyME990A-3F-”X” ExceleratorTM 3” Single Flange Internal Valve - with Pneumatic Actuator







Marshall Excelsior’s 3”- 300 LB Flanged Internal Valves are intended for use on transport trucks,bobtail trucks and large storage tanks with 3” flanged connections in directional or bi-directionalflow applications. Provides both manual shut-down as well as excess flow closing in the event of the piping being separated from the valve. Can be equipped with a pneumatic actuatoropen/closing device.

FEATURES: • All stainless construction• Precision machined stem and stem guide• Fully retained Nitrile seat disc• Largest variety of excess flow closing values• Corrosion resistant sleeved flange bolt holes• Xylan coated corrosion resistant mounting

studs• Removable data plate

• Threaded packing gland with seal ejector spring

• Standard construction utilizes Nitrile seals• Available with Neoprene, Viton®, or

Kalrez® seals• UL Listed for LPG & NH3 service• RulonTM bearings on stem and stub shafts

3” - 300 LB Flanged Internal Valves MARSHALL EXCELSIOR


ME990-3F SERIES

INTERNAL VALVES






ME994S-3F-24-260 (260 GPM)

The ME994S-3F Series Valves feature our new modular Excela-Flange 3”- 8 bolt outlet flange design that can be easily adapted to either 3” NPT or socket weld companion flanges (MEP994S-3F-3SW) making it universal to either piping construction.

• Durable steel body with cadmium surface plating• Universal 3”- 8 bolt outlet flange connection

for threaded or welded piping• Universal 3”- 8 bolt outlet flange provides a

built-in union joint for easy servicability• All stainless internal component construction• One piece threaded packing gland• Precision machined hard coated stem and


• Roller cam actuation• Industry’s fastest bleed time• Removable data plate• Industry’s easiest valve to service• Standard construction utilizes Nitrile seals• Available with Neoprene, Viton®, or Kalrez® seals• Available with 316 Stainless Steel bodies• UL Listed for LPG and NH3 service• RulonTM bearings on stem and stub shafts• Fits standard 3”- 300# flanged tank openings

FEATURES:

3” - 300 LB X 3” - 8 Bolt Universal Companion Flange Series MARSHALL EXCELSIOR







Item No. Description Weight (Lbs.)ME994S-3F-24-”X” ExceleratorTM 3”- 300 lb. Modified Single Flange x 3”- 8 Bolt Companion Flange Internal Valve - Only 38.3

ME994SA-3F-24-”X” ExceleratorTM 3”- 300 lb. Modified Single Flange x 3”- 8 Bolt Companion Flange Internal Valve - w/Pneumatic Actuator 52.8

ME994SAR-3F-24-”X” ExceleratorTM 3”- 300 lb. Modified Single Flange x 3”-8 Bolt Companion Flange Internal Valve - w/Rotary Actuator 45.9


ME994S-3F-24 SERIES


45 46

BB

INTERNAL VALVES

ME990-4F Series

3” - 300 LB Double Flanged Offset Internal Valves MARSHALL EXCELSIOR

• To order Kalrez® add “K” for Kalrez® after the prefix part number i.e. ME990SK-3DFO-300

• To order Neoprene add “N” for Neoprene after the prefix part number i.e. ME990SN-3DFO-300• To order Viton® add “V” for Viton® after the

prefix part number i.e. ME990SV-3DFO-300• Viton® and Kalrez® are trademarks of DuPont

Performance Elastomers.NOTE: Indicate desired excess flow closing value when ordering - see chart for values i.e.

ME990S-3DFO-250 (250 GPM)

The 3” Double Flanged Off-Set Internal Valves are intended for use on bobtail delivery trucks with3” flanged connections in directional or bidirectional flow applications. The 3” offset outlet flange prevents pump installation interference with truck frame rails, cross members, PTO covers, drive shafts, and other common obstacles when remounting bobtail vessels onto newchassis. In order to reduce the amount of offset from the 2” maximum to 1-1/4”, simply rotatethe inlet flange connection by 1 bolt hole either direction. To eliminate the offset entirely, simplyrotate 1 more bolt hole. The ExceleratorTM offset is equipped with three separate packing glandlocations to prevent interference while mounting the valve actuator regardless of how you choose to mount the valve. Provides both manual shut-down and excess flow closing in the event of the valve being separated from the tank. Can be equipped with pneumatic or rotary actuator open/closing devices. All valve models are equipped with a break-away feature in thecast body which permits the pump or piping to shear off in the event of side impact, leaving the valve poppet intact and protecting the tank from catastrophic product loss.

• Body outlet flange offset 2” from inlet flange• Standard with 3 gland ports for stem relocation (2 plugged)• Each gland port can accept pneumatic or

rotary type actuators• Durable steel body with cadmium surface


stem guide• Fully retained Nitrile seat disc• Largest variety of excess flow closing values• Corrosion resistant sleeved flange bolt holes

• Xylan coated corrosion resistant mounting studs• Roller cam actuation• Industry’s fastest bleed time• Removable data plate• Industry’s easiest valve to service• Standard construction utilizes Nitrile seals• Available with Neoprene, Viton®, or Kalrez® seals• Available with 316 Stainless Steel bodies• UL Listed for LPG and NH3 service• RulonTM bearings on stem and stub shafts

FEATURES:

Item No. DescriptionME990S-3DFO-”X” Offset Bobtail Internal Valve - OnlyME990SA-3DFO-”X” ExceleratorTM 3” Double Flange Offset Bobtail Internal Valve (Pneumatic Actuator)

ME990SAR-3DFO-”X” ExceleratorTM 3” Double Flange Offset Bobtail Internal Valve (Rotary Actuator)








4” - 300 LB Flanged Internal Valves MARSHALL EXCELSIOR

4” Flanged Internal Valves are for use on transport trucks and large storage tanks with 4” flangedconnections in directional or bidirectional flow applications. The all stainless construction valves provide manual shut-down and excess flow closing should the piping become separated from thevalve. Can be equipped with manual latch, pneumatic or rotary actuator open/closing devices.

FEATURES: • Precision machined stem and stem guide• Fully retained disc• Largest variety of excess flow closing values• Corrosion resistant sleeved flange bolt holes• Xylan coated corrosion resistant mounting studs• Available with standard or #5 mesh filter screen

• Removable data plate• Threaded packing gland with seal ejector spring• Standard construction utilizes Nitrile seals• Available with Neoprene, Viton®, or Kalrez® seals• UL Listed for LPG and NH3 service• RulonTM bearings on stem and stub shafts

• For #5 Mesh screen add/5 e.i. ME990-4F-650/5• To order Kalrez® add “K” for Kalrez® after the

prefix part number i.e. ME990AK-4F-500• To order Neoprene add “N” for Neoprene after

the prefix part number i.e. ME990AN-4F-500• To order Viton® add “V” for Viton® after the

prefix part number i.e. ME990AV-4F-500• Viton® and Kalrez® are trademarks of DuPont

Performance Elastomers.NOTE: Indicate desired excess flow closing value when ordering - see chart for values i.e.

ME990-4F-650 (650 GPM)

ME990-4F Series

INTERNAL VALVES

Item No. DescriptionME990-4F-”X” ExceleratorTM 4” Single Flange Internal Valve - OnlyME990A-4F-”X” ExceleratorTM 4” Single Flange Internal Valve - with Pneumatic Actuator

ME990AR-4F-”X” ExceleratorTM 4” Single Flange Internal Valve - with Rotary Actuator

ME990M-4F-”X” ExceleratorTM 4” Single Flange Internal Valve - with Manual Latch







ME990-4F SeriesCutaway View

Alternate Gland Ports (Plugged)


47 48

B B

Item No. Inlet Outlet Closing Flow GPM Propane LPG Vapor Capacity Closing Flow Material Connection Connection Half Full (SCFH/Propane) GPM Ammonia One Way Two ways Coupling Coupling 25 PSIG 100 PSIG NH3 + LPG

6902900101 — 1-1/4” M NPT 1-1/4” F NPT 30 — 5,800 9,100 27 6902900102 — 1-1/4” M NPT 1-1/4” F NPT 50 35 650 12,900 45 6902900103 — 1-1/4” M NPT 1-1/4” F NPT 80 65 10,950 18,800 72 6902900104 6902900130 2” M NPT 2” F NPT 100 60 21,550 36,800 90 6902900105 6902900131 2” M NPT 2” F NPT 150 90 33,600 57,200 135 6902900106 6902900132 Steel 2” M NPT 2” F NPT 250 130 — — 225 6902900107 6902900112 3” M NPT 3” F NPT 150 100 28,600 48,700 135 6902900108 6902900113 3” M NPT 3” F NPT 200 125 43,500 73,900 180 6902900109 6902900114 3” M NPT 3” F NPT 250 165 51,500 87,600 225 6902900110 6902900115 3” M NPT 3” F NPT 400 235 80,100 139,000 360 6902900111 6902900116 3” M NPT 3” F NPT 500 325 — — 450

4”- 300 LB & 6” - 300 LB Double Flanged Internal Valves MARSHALL EXCELSIOR

• To order Kalrez® add “K” for Kalrez® after the prefix part number i.e. ME990SKAR-4DFM-375

• To order Viton® add “V” for Viton® after the prefix part number i.e. ME990SVAR-4DFM-375



ME990SAR-4DFM-375 (375 GPM)

Marshall Excelsior’s 4” & 6” 300 LB Double Flanged Internal Valves are intended for use on transport trucks and large storage tanks with 4” or 6” flanged connections in directional or bi-directional flow applications. Provides both manual shut-down and excess flow closing in the event of the piping being seperated from the valve. Equipped standard with a rotary actuator open/closing devices. All valve models are equipped with a break-away feature in the cast body which permits the pump or piping to shear off in the event of side impact, leaving the valve poppet intact and protecting the tank from catastrophic product loss.

• Durable steel body with cadmium surface plating• All stainless internal component construction• One piece threaded packing gland• Precision machined hard coated stem and


• Roller cam actuation• Industry’s fastest bleed time• Removable data plate• Industry’s easiest valve to service• Standard construction utilizes Nitrile seals• Available with Neoprene, Viton®, or Kalrez® seals• Available with 316 Stainless Steel bodies• UL Listed for LPG and NH3 service• RulonTM bearings on stem and stub shafts

FEATURES:

ME990SAR-4DFM

Item No. DescriptionME990SAR-4DFM-”X” ExceleratorTM 4”- 300 lb. Modified Double Flange Internal Valve - with Rotary ActuatorME990SAR-6DFM-”X” ExceleratorTM 6”- 300 lb. Modified Double Flange Internal Valve - with Rotary Actuator


Cavagna’s Threaded Internal Valves, designed as primary shut-offs to control product discharge inLP-Gas service, are predominantly used in the liquid and vapor openings of bobtail and other transport vehicles. All valves satisfy the requirements of NFPA 58 and can also be used instationary storage tank applications. All internal valves have a robust, one-piece body design andan incorporated excess flow function. Each valve has a weak section that allows the pump orpiping to “shear” in the event of an accident, thereby leaving the valve mechanism intact. Cavagna threaded valves are compact and can be operated either manually or remotely via cableor pneumatic control. Valves contain spring-loaded, PTFE packing providing excellent leakage protection and the standard disc material provided is Nitrile.

Threaded Internal Valves CAVAGNA GROUP

Cavagna Flanged Valves, equipped with a built-in excess flow valve to prevent uncontrolled product release, are perfect for mounting a pump or other similar piping connections.Mounting bolts weakened section, provided, allow the pump or piping to “shear” in theevent of an accident, thereby leaving the valve intact.

Cavagna flanged valves have a protection filter to avoid pump contamination from dirt andparticles, easily removable when the valve is installed on the filling piping line. Cavagnaflanged valves contain PTFE packing providing excellent leakage protection and thestandard disc material provided is Nitrile, they can be operated manually or remotely viacable or pneumatic control.

Flanged Internal Valve 3” CAVAGNA GROUP

3” FlangedInternal Valve

3” Double Flanged Internal Valve

1-1/4” Threaded Internal Valve







Item No.Material Inlet

ConnectionOutlet

Connection

ClosingFlow GPMPropane

LPG Vapor Capacity(SCFH/Propane)

Closing FlowGPM Ammonia

NH3 + LPGSingle Double 25 PSIG 100 PSIG

6902900117 6902900122

Steel3” 300 lb. ANSI RFModified (4-7/8”)

3” 300 lb.ANSI RF

150 25,100 42,700 1356902900118 6902900123 200 36,900 62,800 806902900119 6902900124 250 42,200 71,800 2256902900120 6902900125 400 59,400 100,900 3606902900121 6902900126 500 — — 450


49 50

B B


MEP650 ExceleratorTM Open/Close Cable Control Release with 50’ Cable MEP651 ExceleratorTM Open/Close Cable Control Release - Only


ME990-10-902 ExceleratorTM Manual Latch Assembly for 1-1/4” Threaded Internal Valves MEP990-24 ExceleratorTM Manual Latch Assembly for ME990-16 and 990-24 Series MEP990-4F ExceleratorTM Manual Latch Assembly for ME990-4F Series


1401101518 8 Screws - 3/4 - 10 UNC 3001102611 16 Nuts (8 Up + 8 Down) 3/4 - 10 UNC 0401105575 1 Upper Gasket 0401105576 1 Lower Gasket 1401101522 8 Screws - M 20 x 2,5 3001102628 16 Nuts (8 Up + 8 Down) M 20 x 2.5


1401101517 16 Screws (8 Up + 8 Down) 3/4 - 10 UNC 3001102611 16 Nuts (8 up + 8 down) 3/4 - 10 UNC 0401105575 1 Upper Gasket 0401105576 1 Lower Gasket


14011015198 Screws - 3/4 - 10 UNC 3001102611 16 Nuts (8 Up + 8 Down) 3/4 - 10 UNC 0401105595 1 Upper Gasket 0401105596 1 Lower Gasket

Item No. Material

Inlet Outlet Closing Flow Connection Connection GPM Propane

6902900141 340 6902900142 440 6902900143 600 6902900144 800 6902900145 1,000

Latches MARSHALL EXCELSIOR

Releases MARSHALL EXCELSIOR

INTERNAL VALVES & ACCESSORIES INTERNAL VALVE ACCESSORIES

Cavagna Flanged Internal 4” Valves come equipped with a built-in excess flow valve to preventuncontrolled product release, and are ideal for mounting a pump or other similar pipingconnections. Mounting bolts allow piping to shear in the event of an accident, leaving the valveintact. Flanged valves have a protection filter to avoid pump contamination from dirt, contain PTFE packing to provide excellent leakage protection, disc material is Nitrile, and can be operatedmanually or remotely via cable or pneumatic control.

Flanged Internal Valve 4” CAVAGNA GROUP

4” 300 lb. ANSI RFModified (4-7/8”)

4” 300 lb.ANSI RFSteel

ME990-10-902

MEP990-4F

MEP990-24

MEP651

4” FlangedInternal Valve

Flanged Internal Valve Accessories for 3” Single Flanged Valve CAVAGNA GROUP

Flanged Internal Valve Accessories for 3” Double Flanged Valve CAVAGNA GROUP

Flanged Internal Valve Accessories for 4” Single Flanged Valve CAVAGNA GROUP

8 Screws

16 Nuts(8 up and 8 down)

1 UpperGasket

1 Lower Gasket

16 Screws(8 up and8 down)

16 Nuts(8 up and 8 down)

1 UpperGasket

1 Lower Gasket

8 Screws

16 Nuts(8 up and8 down)

1 UpperGasket

1 LowerGasket


51 52

C C

Item No. Actuator

Fits MEC* Fits* Internal Valve Type

ME205 AirstrokeTM

ME990-10 Fisher® C407 1-1/4” Threaded by Firestone

ME205R AirstrokeTM

— REGO® A3209R 1-1/4” Threaded by Firestone

ME206

#9 Chamber ME990-16, ME990-24, Fisher® C402, C421, C471, 2” and 3”

ME990S-3F-24 C427, C477 Threaded

ME207

#9 Chamber ME990S-3DF Fisher® C403-24 3” Double

ME990S-3DFM C483-24 Series FlangeME207SF #9 Chamber — Fisher® C404-24 Series 3” Single Flange

ME208SF

#24 Chamber ME990-4F Fisher® C404-32 4” Single

C484-32 Series FlangeME710 AirstrokeTM — REGO® Flowmatic® Three-Way Valve


1309500142 Fuse Latch Threaded Internal Valve 2” and 3”1309500143 Fuse Latch Threaded Internal Valve 1-1/4” X 1-1/2”1309500144 Dual Latch/Remote Release for Internal Valve 1-1/4” X 1-1/2”1309500147 Manual Lever and Release for 4” Internal Valve

1309500143

ACTUATORSINTERNAL VALVE ACCESSORIESLatch/Remote Release Mechanisms CAVAGNA GROUP

1309500142

1309500144

1309500147

Internal Valve Actuators PowerTorq Series MARSHALL EXCELSIOR

*Also fits Cavagna 6902900 Series internal valves | Fisher® and Fisher® Internal Valves are the trademarks of Emerson Process Management | Cavagna is the trademark of Cavagna Group

Direct Drive Actuators are designed to maximize the life of the internal valve by eliminating sidepressure on the valve’s packing stem. These actuators are intended to be used at remote locations or operated directly off the air brake system in bobtail or transport applications.

The low temperature factory installed seals allow these actuators to be used with air, nitrogen, carbon dioxide or LP-Gas vapor. In case of a fire, the factory-provided thermal plug melts at 212° F., releasing pressure allowing the internal valve to close. The factory set rotation of these actuators require no modification and can be oriented in any direction.

• Stainless steel all weather mounting hardware• Field repairable under full tank pressure• Anodized aluminum actuator body with easy to see open/close indicator

FEATURES: • No pinch points for operator safety• Includes mounting bracket for ME707

Quick Release Valve NOTE: ME707 is not required for operation• Installation hardware is provided

ME225Internal Valve Not

Included

ME227

ACTUATORS

Internal Valve Actuators Powerstroke & Fastroke Series MARSHALL EXCELSIOR

* Also fits Cavagna 6902900 Series internal valves

PowerStroke and FASTroke Actuators are designed with a heavy duty stainless steel frame to withstand the toughest conditions. These actuators are intended to be used at remote locationsor operated directly off the air brake system in bobtail or transport applications.

Smooth acting cam opens the internal valve lever when air, nitrogen, or carbon dioxide is appliedto the line. When line pressure is released, the internal valve automatically closes. In case of a fire,the thermal plug melts at 212° F, releasing pressure allowing the internal valve to close.

• Stainless steel all weather bracket• Field repairable without complete disconnect

from internal valve• Repairable with common automotive brake chamber

• High gloss auto grade black epoxy coating• Installation hardware is provided• Standard disc material is Nitrile• No modification required

FEATURES:

ME205

ME207

ME208SF

ME206

ME205R

ME710

Item No. Actuator Type Fits MEC* Fits Fisher* Internal Valve

ME225

Direct Drive

ME990-10, ME991-10, ME992-10 Fisher® C407 1-1/4” Threaded

ME226

ME990-16, ME990-24,ME990S-3F-24, ME990S-2DFM,

ME991-16, ME991-24, ME992-16,ME992-24, ME993S-16,

ME993S-24

Fisher® C402, C421, C427,C471, C477

2” & 3” Threaded

ME227 ME990S-3DF &ME990S-3DFM

Fisher® C403-24 &C483-24 Series 3” Double Flange

ME228 ME990-4F Fisher® C404-32 &C484-32 Series 4” Single Flange


53 54

C C

Item No. Description Latch Type OAL

ME980-6 3/4” FNPT Emergency Shutoff Valve (ESV) Pneumatic 4-3/4”ME980-8 1” FNPT Emergency Shutoff Valve (ESV) Pneumatic 4-3/4”ME980C-6 3/4” FNPT Emergency Shutoff Valve (ESV) Cable 4-3/4”ME980C-8 1” FNPT Emergency Shutoff Valve (ESV) Cable 4-3/4”

Item No. Fits

3000900000 O-205 Actuator 1-1/4” and 1-1/2”3000900001 O-206 Actuator 2” and 3”3000900002 O-207 SF Actuator 3” Single Flanged3000900003 O-207 Actuator 3” Double Flanged3000900004 O-208 SF Actuator 4” Single Flanged

Item No. Inlet Outlet

ME707 3/8” FNPT 3/8” FNPT (2 Ports)ME708 1/4” FNPT 1/4” FNPTME709 1/4” FNPT 1/4” MNPT

Rotary Cams Actuators CAVAGNA GROUP

• Immediate and automatic closing in absence of air (rapid discharge accessories are not

needed)• Open/close indicator• Compact design and lightweight

FEATURES: • Stainless steel valve anchoring bracket• Aluminum body, stainless steel and aluminum components• Self-lubricating with PTFE carbon-graphite

seals• Operating media: compressed filtered air,

not necessarily lubricated• 500,000 opening cycles guaranteed

Cavagna’s Rotary Cams Actuators are pre-assembled, ready for quick installment, and can beattached to the valve in four separate positions. The direct drive design does not apply side loadto internal valve stem packing, which maximizes valve life. An internal cam mechanismguarantees high performance, optimizing the opening torque. The return torque movement relies only on the spring and is independent from the supply pressure. The actuator guaranteescomplete opening of the valve and is equipped with a limit switch.

ACTUATORS

ACTUATOR ACCESSORIESActuator Accessories MARSHALL EXCELSIOR

ME707 - The quick release valve is used in conjunction with Marshall Excelsior’s air actuators to decrease the response time when closing actuators. They are particularly effective when long distances (75 feet or more) exist between the actuator and the actuator control valve.

ME707 - The 0-150 PSIG air pressure regulator prolongs the life of the air actuator and air systemby allowing the air pressure to be set and regulated at the minimum required operating pressure for each individual system.

ME709 - The gas/air filter is used to filter foreign materials and/or particles from LP-Gas systems such as motor fuel/carburetion systems. These filters to be used on air supply lines for internal andemergency shutoff valve actuator systems.

EMERGENCY SHUTOFF VALVES3/4” and 1” Emergency Shutoff Valves MARSHALL EXCELSIOR

Emergency Shutoff Valves (ESVs) provide rapid and positive shutdown of gas lines should a down stream rupture or piping break occur. Due to the presence of a built-in fusible element, the ESV will automatically close when exposed to heat between 212° F - 250° F. These valves aresuited for installation at direct fired vaporizer inlets for automatic emergency shutdown as a result of fire or at dispensing pump inlets to provide immediate and positive remote shutdown.

• Powder coated ductile iron body with cast hexagonal ends

• Integral swing away check valve with soft seat to promote maximum product flow and

minimize product loss in the event line failure• All stainless steel, corrosion resistant internal component construction• Indicator clearly shows if valve is open/closed

FEATURES: • UL Listed for use with LP Gas and Anhydrous Ammonia - 400 PSI WOG• Integral fusible element for automatic

closure when exposed to fire• Durable Teflon® packing gland and resilient

seals provide long lasting service life• Available with pneumatic or cable style

latch mechanism

ME980C-6

ME707

ME708 ME709

1-1/4” and 1-1/2”

Actuator

2” and 3”Actuator

3” SingleFlanged Actuator

3” DoubleFlangedActuator

4” SingleFlangedActuator

C


55 56

C

Item No. Description Latch Type Flange Material OAL

ME980-10 1-1/4” FNPT Emergency Shutoff Valve (ESV) Pneumatic Ductile Iron 5-3/8”ME980C-10 1-1/4” FNPT ESV Cable Ductile Iron 5-3/8”ME980-16 2” FNPT ESV Pneumatic Cast Steel 6-7/8”ME980C-16 2” FNPT ESV Cable Cast Steel 6-7/8”ME980-24 3” FNPT ESV Pneumatic Ductile Iron 9-5/8”ME980C-24 3” FNPT ESV Cable Ductile Iron 9-5/8”ME980-16-2F 2” - 300 lb. Flange ESV Pneumatic 11-7/8”ME980C-16-2F 2” - 300 lb. Flange ESV Cable 11-7/8”ME980-24-3F 3” - 300 lb. Flange ESV Pneumatic

Ductile Iron 14-1/8”

ME980C-24-3F 3” - 300 lb. Flange ESV Cable 14-1/8”ME980-24-4F 4” - 300 lb. Flange ESV Pneumatic 14-1/4”ME980C-24-4F 4” - 300 lb. Flange ESV Cable 14-1/4”

Item No. Actuator Type Fits MEC Fits ESV

ME551 AirstrokeTM by ME980-10, ME980-16, ME980-16-2F, Fisher® N550 1-1/4”, Firestone ME980-24, ME980-24-3F, ME980-24-4F Series 2”, 3”

ME552 Direct Drive ME980-10, ME980-16, ME980-16-2F, Fisher® N550 1-1/4”,

ME980-24, ME980-24-3F, ME980-24-4F Series 2”, 3”

ME552 Operating Pressure Limits

Minimum 25 PSIGMaximum 125 PSIGRecommended 40 - 60 PSIG

ME551 Operating Pressure Limits

Minimum 20 PSIGMaximum 125 PSIGRecommended 20 - 25 PSIG

ME980-10

Emergency Shutoff Valve (ESV) | To order ESV with Pneumatic Actuator add “A” after the prefix part number i.e. ME980A-10 | To order ESV with Rotary Actuator add “AR” after the prefix part number i.e. ME980AR-10

1-1/4” - 3” Emergency Shutoff Valves MARSHALL EXCELSIOR

Emergency Shutoff Valves (ESVs) are designed to provide rapid and positive shutdown of gas lines should a down stream rupture or piping break occur. Due to the presence of a built-in fusibleelement at the valve operating hub, the ESV will automatically close when exposed to heat between 212° F - 250° F. These valves are ideally suited for installation at bulkheads or inline plumbing for automatic emergency shutdown as a result of fire or to provide immediate and positive manual or remote shutdown.

• Durable powder coated ductile iron body• Removable flanged ends for easy field service• Integral swing-away check valve with soft

seat to promote maximum product flow and prevent reverse product flow

• All stainless steel, corrosion resistant internal component construction

FEATURES: • UL Listed for use with LP Gas and Anhydrous Ammonia - 400 PSI WOG• Integral fusible element for automatic

closure when exposed to fire• Durable Teflon® packing gland and resilient

seals provide long lasting service life• Available with pneumatic or cable style

latch mechanism

EMERGENCY SHUTOFF VALVES EMERGENCY SHUTOFF VALVES

ME980-16-2F

ME980-24

Emergency Shutoff Valve Actuators MARSHALL EXCELSIOR

Emergency Shutoff Valve Actuators are to be used with emergency shutoff valves in remote locations. Pressure to the line enables a smooth acting cam to completely open the emergencyshutoff valve for full flow operation. When line pressure is released, the emergency shutoff valveautomatically closes. In case of a fire a thermal plug melts at 212° F, allowing the ESV to close.

Modification is not required to actuators and all installation hardware is provided. The PowerTorqdirect drive actuator maximizes the life of the emergency shutoff valve, eliminating side pressureon the packing stem.

ME552 FEATURES: • Stainless steel, all weather mounting hardware• Field repairable under full tank pressure• Low temperature seals allow use with air,

nitrogen, carbon dioxide or LP-Gas vapor• Anodized aluminum actuator body with

easy to see open/close indicator• No pinch points for operator safety• Factory installed thermal plug• Includes mounting bracket for ME707

Quick Release Valve

NOTE: ME707 is not required for operation

ME551 FEATURES: • Heavy duty stainless steel all weather

bracket• Use with air, nitrogen or carbon dioxide• Uses existing Fisher® thermal plug

AirstrokeTM is a trademark of Firestone Industrial Products Company | Fisher® and Fisher® Internal Valves aretrademarks of Emerson Process Management

ME552

ME551

ME980-16


57 58

C C

EMERGENCY SHUTOFF VALVES EMERGENCY SHUTOFF VALVES

High Capacity - Flanged MARSHALL EXCELSIOR

Emergency Shutoff Valves (ESV’s) are designed to provide rapid and positive shutdown of gas lines should a downstream rupture or piping break occur. Due to the presence of a built-in fusible element at the valve operating hub the ESV will automatically close when exposed to heat between 212° F - 250° F. These valves are ideally suited for installation at bulkheads or inline plumbing for automatic emergency shutdown as a result of fire or to provide immediate and positive manual or remote shutdown.

• Cadmium plated steel/ductile iron body for maximum durability

• Long stroke internal valve poppet for maximum product flow

• All stainless steel internal component construction provides maximum corrosion resistance

• Flanged end connection for ease of field service

• UL Listed for LPG and Anhydrous Ammonia - 400 PSI WOG

• Integral fusible element for automatic closure when exposed to fire

• Durable Teflon® packing gland and resilient seals provide long lasting service life

• Pre-mounted inlet bell housing for quick and easy installation

• All mounting hardware included

FEATURES:

Item No. Description Actuator TypeME980SAR-4DFM 4” - 300LB Flange Emergency Shutoff Valve (ESV) RotaryME980SAR-6DFM 6” - 300LB Flange Emergency Shutoff Valve (ESV) Rotary

High Capacity - Flanged Accessories/Repair Kits MARSHALL EXCELSIOR


MEP990-4DFM 4” - 300LB Double Flange ESV/ISC Bell Housing Converstion Kit - fits ME990S-4DFMMEP990-6DFM 6” - 300LB Double Flange ESV/ISC Bell Housing Converstion Kit - fits ME990S-6DFM

ME980SAR-4DFM

ME980SAR-4DFMCutaway View

MEP990-4DFM Bell Housing

High Flow Railcar ESV MARSHALL EXCELSIOR

Excelerator Railcar Emergency Shutoff Valves (ESV’s) are designed to provide rapid and positiveshutdown of gas lines should a downstream rupture or piping break occur during product transfer.Featuring a built-in fusible element at the valve operating hub to ensure the ESV will automaticallyclose when exposed to heat between 212° F. - 250° F. In addition to the fusible element, the Excelerator Railcar ESV’s are equipped with a poppet design similar the MEC internal safety valves that provides an integral excess flow feature. MEC offers a variety of closing flow valuesranging from very high liquid flow rates to more moderate vapor flow rates depending on theapplication. MEC Excelerator Railcar ESV’s are equipped standard with quick disconnect internalpneumatic operators for rapid and reliable open/close of the poppet allowing for convenient onsite or remote shutdown of the valve.

• 316 stainless steel body• All stainless steel internal component

construction provides maximum corrosion resistance

• Hardened stainless steel flanged end connection for durability and ease of field service

• UL Listed for LPG and Anhydrous Ammonia - 400 PSI WOG

• Integral fusible element for automatic closure when exposed to fire

• Durable PTFE packing gland with resilient seals providing long lasting service

• 100% field repairable - no special tools required

• E-Z grip ribs for installation even with heavy protective hand wear

FEATURES:

Item No. Description Closing FlowGPM/LPG

ME983-16/150 High Flow Railcar ESV 2” FNPT X 2” FNPT 150*ME983-16/250 High Flow Railcar ESV 2” FNPT X 2” FNPT 250

ME983-16/500 High Flow Railcar ESV 2” FNPT X 2” FNPT 500

ME983-16 High Flow Railcar ESV 2” FNPT X 2” FNPT ~

* Recommended for vapor service - approx. closing flow 71,000 SCFH/LPG | ~ Availlable with Kalrez, Viton and Neoprene seal materials | ~ For NH3 multiply GPM by .90

ME983 Series

ME983 SeriesCutaway View

Flanged Adapting Spool Kits MARSHALL EXCELSIOR

Flanged Adapting Spool Kits are used in conjunction with MEC’s flanged internal valves for excess flow protection on inline or drop down weld neck tank construction to safely increase ordecrease tank connections or line sizing in accordance to NFPA #58 code requirements. Each bell housing is carefully contoured to allow ample unrestricted flow around the internal valve closing poppet for accurate and reliable excess flow protection in the event of a downstream line failure or separation. Ideally suited for protection of weld neck tank openings, asreplacements to traditional emergency shut off (ESV) installations or to adapt flanged vapor relief tank openings from 4” to 3” or vice versa such as needed to replace ACF type relief valves.

Item No. Description Fits Internal Valve Models

MEP990-4DFM/3DFM 4”-300LB x 3”-300LB Flanged ACF/ESV/ISCAdapting Spool Kit ME990S-4DFM Series

• Cadmium plated ductile iron body for maximum durability

• Precise interior contour for maximum flow around internal valve poppet

• Includes all studs/nuts and gaskets

• Suitable for use as inline ESV when used in conjunction with ExceleratorTM Internal Valves (internal valve sold separately)

• For use with LPG and NH3 - 400 PSI WOG

FEATURES:

MEP990-4DFM/3DFM


59 60

D

C

No. of Flow Capacity Factory Installed Relief Valve Accessory Item No.

Flange Relief Application SCFM/Air** UL @ Seal Start-to-Discharge Part No.

8 Stud/Nut Universal

Size Valves 120% Set Pressure Material* Setting PSIG Mounting Kit

ME903S-3F/250VM 3”- 300#**

3 LPG 20,400** Viton® MEV250VM/250ME903S-3F/250CN 3 LPG & NH3 20,400** Nitrile

250 MEV250CN/250

ME903S-4F/250VM 4”- 300#

3 LPG 20,400** Viton® MEV250VM/250ME903S-4F/250CN 3 LPG & NH3 20,400** Nitrile MEV250CN/250ME904S-3F/250VM

3”- 300# ** 4 LPG 27,740*** Viton® MEV250VM/250

ME904S-3F/250CN 4 LPG & NH3 27,740*** Nitrile 250

MEV250CN/250ME904S-4F/250VM

4”- 300# 4 LPG 27,740*** Viton® MEV250VM/250

ME904S-4F/250CN 4 LPG & NH3 27,740*** Nitrile MEV250CN/250 ME904SK

ME903S-3F/265VM 3”- 300# **

3 LPG 20,555** Viton® MEV250VM/265ME903S-3F/265CN 3 LPG & NH3 20,555** Nitrile MEV250CN/265ME903S-4F/265VM

4”- 300# 3 LPG 20,555** Viton® MEV250VM/265

ME903S-4F/265CN 3 LPG & NH3 20,555** Nitrile 265

MEV250CN/265ME904S-3F/265VM

3”- 300# ** 4 LPG 28,550*** Viton® MEV250VM/265

ME904S-3F/265CN 4 LPG & NH3 28,550*** Nitrile MEV250CN/265ME904S-4F/265VM

4”- 300# 4 LPG 28,550*** Viton® MEV250VM/265

ME904S-4F/265CN 4 LPG & NH3 28,550*** Nitrile MEV250CN/265

ESV/Internal Valve Accessories MARSHALL EXCELSIOR

EMERGENCY SHUTOFF VALVES ACCESSORIES RELIEF VALVES

Quad-Port Relief Valve Manifolds are designed for use with large LP-Gas and NH3 stationary storage containers with flanged openings. These relief manifolds have an additional relief valveexcluded from the flow rating, which allows for service and/or exchange of any one relief valvewithout evacuating the tank. The large port selection handle allows for each specific valve portto be closed off so the relief valve may be removed while the remaining valves remain under pressure, protecting the tank and contents. Each manifold model is rated based on the flow through the relief valves with one valve removed from service.

Quad-Port Relief Valve Manifold MARSHALL EXCELSIOR

* Nitrile not UL Listed | ** For use with modified 300 # ANSI Flange with 4” port | *** Flow rating based on number of valves indicated inparenthesis () | Flow rates are shown as bare relief valves, pipe-aways will reduce flow | Teflon® is a trademark of DuPont Company | Viton® is atrademark of DuPont Performance Elastomers.

• Heavy duty ductile iron body• Corrosion resistant finish• Durable V-cup Teflon® packing stem seals• Molded rubber weather guard for manifold

rotary gear with port plug• Integral breakaway feature leaves seat and

seal intact

FEATURES: • Includes weep hole deflector and hex

socket plugs• Integrated pilot equalizing feature• Includes convenient lifting chain• 3-1/2”- eight outlet thread accepts 3” MNPT pipe-away

ME903S-3F/250VM

ME980-905-25

3330ESV Palm Valve

The ESV Palm Valve is a mechanical, poppet valve. Their compact size requires little mounting space. The VM series offers a wide variety of actuator styles and flow capacity up to 1.0 Cv.

MEC’s Pneumatic Control / E-Stop Kit is designed to be used in conjunction with MEC’s pneumatic controlled emergency shutoff valves (EVS) or internal valves to remotely open and close using compressed gas. Each kit includes all necessary components for connecting and charging a pneumatic control system complete with brackets, mounting hardware, and necessary placarding in a variety of orientations for fast reliable remote system shutdown.

Item No. DescriptionME980-905 Universal ESV/Internal Valve Remote Release/No CableME980-905-25 Universal ESV/Internal Valve Remote Release with 25’ CableME980-905-50 Universal ESV/Internal Valve Remote Release with 50’ CableME980-906-25 Remote Release Cable Assy. 5/16-24UNF - 25’ OALME980-906-50 Remote Release Cable Assy. 5/16-24UNF - 50’ OAL

ESV Accessories MARSHALL EXCELSIOR

Item No. Description3330 1/4” ESV Palm ValveMEP980PN-100 MEC Complete Pneumatic Controls / E-Stop Kit w/ Placards & 100’ Poly TubingMEP980PN-105 Compression Tube Extension Adapter - 1/8” MNPT x 1/4” CC, BrassMEP980PN-106 Compression Tube Extension Tee - 1/4” CC, BrassMEP980PN-113 Tubing Extension 1/4” x 100 Ft Roll, Poly

• Heavy duty pneumatic control and charging valves

• Predrilled mounting plates and hardware• Large easy to read placards / instruction

labels• Built in leak detection gauge• Easy to install

FEATURES: • Includes 100 Ft of 1/4” poly tubing and

necessary compression connectors• Additional extension tubing and

connectors available• Suitable for use with dry air, nitrogen or

LPG vapor

MEP980PN-100 MEP980PN-100 Installed

Pressure source and regulator not included

ESV and actuatornot included


61 62

DD

Mini Quad-Port Relief Manifold MARSHALL EXCELSIOR

EMERGENCY SHUTOFF VALVES ACCESSORIES RELIEF VALVES

Item No. Relief ValveSTD

Application TankConnection

Size

Relief Valve

***Flow RatingSCFM/AIR @120% of set

pressure

LPG NH3 # of Valves Item No. UL Rating

ME902S-16B/250 250 PSIG Yes No

2” MNPT

2 MEV125B/250 5,115 (1)ME902S-16/250 250 PSIG No Yes 2 MEV125/250 5,115 (1)ME902S-16/265 265 PSIG No Yes 2 MEV125/265 5,855 (1)ME903S-16B/250 250 PSIG Yes No 3 MEV125B/250 9,320 (2)ME903S-16/250 250 PSIG No Yes 3 MEV125/250 9,320 (2)ME903S-16/265 265 PSIG No Yes 3 MEV125/265 10,795 (2)ME904S-16B/250 250 PSIG Yes No 4 MEV125B/250 12,481 (3)ME904S-16/250 250 PSIG No Yes 4 MEV125/250 12,481 (3)ME904S-16/265 265 PSIG No Yes 4 MEV125/265 13,630 (3)

*** Flow rating based on number of valves indicated in parenthesis () | Flow rates shown are for bare relief valves, pipe-aways will reduce flow rates | Note: For 265 PSIG set pressure change part number suffix - i.e. ME903S-16/265 | To order Viton® seal materials add “VM” for Viton® after the prefix part number - i.e. ME904S-16B/250VM

Mini Quad-Port Relief Manifold are for use with large LPG & NH3 stationary storage containers with 2” FNPT openings. These Relief Manifolds have an additional relief valve excluded from the flow rating, which allows for service and/or exchange of any one relief valve without evacuating the tank. Our large port selection handle allows for each specific valve port to be closed off so that the relief valve may be removed while the remaining valves stay under pressure protecting the tank and contents. Each manifold model is rated based on the flow through the relief valves with one valve removed from service.

• Heavy duty ductile iron body• All stainless steel internal components• Durable V-cup Teflon® packing stem seals• Large diameter port selection handle and

port indicator• Molded rubber weather guard for manifold

rotary gear with port plug• Available with 250 PSIG and 265 PSIG

relief valve set pressures

FEATURES: • Vapor equalizing feature for easy port to

port rotation• Includes tank stabilizer nut for maximum

strength at container connection• Covers most 30,000 gallon tanks with

only two manifoldsME903S-16B/250VM

Accessories MARSHALL EXCELSIOR

Item No. DescriptionMEP178 Pipeaway Adapter for MEV125 Series with 2” FNPT Outlet - AluminumMEP178K Pipeaway Adapter Kit with Stabilizer Bracket for ME904S-16

MEP123 Installation/Removal Tool for MEV125 Series Relief Valves

MEP178K(Pipeaway Adapterand Stabilizer Kit)

Mini Quad-Port Tank Sizing Chart MARSHALL EXCELSIOR

Item No. Relief ValveSTD

LPG NH330,000 Gallon

109” O.D.30,000 Gallon

131” O.D.18,000 Gallon

109” O.D.30,000 Gallon

131” O.D.30,000 Gallon

131” O.D.18,000 Gallon

109” O.D.

ME902 Series250 PSIG N/A 5 3 2 2 2250 PSIG N/A N/A 3 2 2 2

ME903 Series265 PSIG 3 3 2 2 1 1250 PSIG 3 3 2 2 1 1

ME902 Series250 PSIG 3 2 2 1 1 1265 PSIG 3 2 2 1 1 1

* Number indicates quantity of relief manifolds to adequated relief vapor overpressure conditions for listed tank surface areas.

Mini Quad-Port Relief Valve Manifold MARSHALL EXCELSIOR

Item No.Application Tank Connection

SizeRelief Valve Port

N N # of ValvesME904S-16 Yes Yes 2” MNPT 1-1/4” FNPT (4)

Item No. DescriptionApplication

LPG NH3

MEV125/250 1-1/4’’MNPT External Relief Valve-Nitrile 250PSI - 6,328 SCFM No YesMEV125/265 1-1/4’’MNPT External Relief Valve-Nitrile 265PSI - 6,542 SCFM No Yes

MEV125B/250 1-1/4’’MNPT External Relief Valve-Nitrile 250PSI - 6,328 SCFM Yes No

MEV125B/265 1-1/4’’MNPT External Relief Valve-Nitrile 265PSI - 6,542 SCFM Yes No

Mini Quad-Port Relief Valve Manifold are for use with large LPG & NH3 stationary storage containers with 2” FNPT openings. These Relief Manifolds have an additional relief valveexcluded from the flow rating, which allows for service and/or exchange of any one relief valvewithout evacuating the tank. Our large port selection handle allows for each specific valve portto be closed off so that the relief valve may be removed while the remaining valves stay underpressure protecting the tank and contents. Each manifold model is rated based on the flow through the relief valves with one valve removed from service.

• Heavy duty ductile iron body• All stainless steel internal components• Durable Teflon® V-pack stem seals• Large diameter port selection handle and

port indicator• Molded rubber weather guard for manifold

rotary gear with port plug

FEATURES: • Vapor equalizing feature for easy port to

port rotation• Includes tank stabilizer nut for maximum

strength at container connection

ME904S-16

MEV125/250


63 64

DD

Item No.Container

ConnectionMNPT

SealMaterial*

Start-to-Discharge

SettingPSIG

OAL WrenchHex

Flow CapacitySCFM/Air**UL @ 120%Set Pressure

Application Accessories

MEV25/60

1/4”

Nitrile

60

1-59/64” 7/8”

—

LPG

MEP173Pipe-away Adapter

MEV25/250 250 —MEV25/312 312 —MEV25/375 375 —MEV50/250

1/2”250

2-1/2”

1 - 1/8”

200

MEP174Pipe-away Adapter

MEV50/375 375 —MEV75/250

3/4”250

2-21/32”—

MEV75/312 312 —MEV75/375 375 —MEVS-PVE431B/250 3/4”

Nitrile250 3-21/32”

1 - 3/4”1,740 MEP173 Pipeaway

AdapterMEVS-PVE431/250 1” 250 4” 1,740

RELIEF VALVES RELIEF VALVES1/4”NPT - 1” NPT External Pressure Relief Valves MARSHALL EXCELSIOR

These External Pressure Relief Valves are designed for installation in stationary ASME applications such as bulk plant, skid tanks, underground and above ground containers, as the primary pressure relief valve.

NOTE: This valve and all working parts are to be installed outside the container. Therefore, to ensure proper operation of the valve, the valve must be protected from damage and inspectionsperformed as prescribed by Marshall Excelsior.

* Nitrile and Kalrez® not UL Listed | ** Flow rates are shown for bare relief valves, pipe-aways will reduce flow | *** Per NFPA 58, table 5.7.2.5 area shown is for UL or ASME flow rating, which ever is greater | Viton® and Kalrez® are trademarks of DuPont Performance Elastomers. NOTE: Kalrez option available

FEATURES: • Brass construction for LP-Gas application• Compact design to fit any application• Stainless steel spring• Specially designed internal components to

increase flow at discharge

Item No.Container

ConnectionMNPT

SealMaterial*

Start-to-Discharge

SettingPSIG

OAL WrenchHex


Suitable fortanks w/

surface areaup to: ***

ApplicationAccessories

LPG NH3

MEV125B/250

1/4”

Nitrile 250

10-1/2”

2-11/16”

6,330 340 Sq. Ft.

YES NOMEV125-109

Replacement Cap

MEP178Pipeaway Adapter

MEP123Installation /Removal Tool

MEV125B/265 Nitrile 265 6,545 350 Sq. Ft.MEV125BVM/250 Viton® 250 6,330 340 Sq. Ft.MEV125BVM/265 Viton® 265 6,545 350 Sq. Ft.MEV125/250 Nitrile 250 6,330 340 Sq. Ft.

NO YESMEV125/265 Nitrile 265 6,545 350 Sq. Ft.MEV125VM/250 Viton® 250 6,330 340 Sq. Ft.

YES

NOMEV125VM/265 Viton® 265 6,545 350 Sq. Ft.MEV250VM/250

2-1/2”

Viton® 250

4 - 1/8”

10,333 610 Sq. Ft. MEP170Relief Valve Adapter

MEP250Installation/

Removal Tool

MEV250CN/250 Nitrile 250 10,333 610 Sq. Ft. YESMEV250VM/265 Viton® 265 10,948 655 Sq. Ft. NOMEV250CN/265 Nitrile 265 10,948 655 Sq. Ft. YES

1-1/4” & 2-1/2” NPT External Pressure Relief Valves MARSHALL EXCELSIOR

MEV250VM/250Top View

MEV250VM/250 MEP250

MEP170

MEV50/250

MEVS-PVE431/250

MEV125 Series are for use with large LPG & NH3 storage containers as a primary pressure relief valve on ASME above and below ground bulk plant installations. All working components are external to the container connection away from possible product contaminants. Compatible with 1-1/4” FNPT multiple head units including ME902S-16, ME903S-16 and ME904S-16 Series Mini Quad-Port Manifolds.

MEV250 Series are designed for use with storage containers as a primary pressure relief valve on ASME above and below ground installations. All working components and external to the container connection away from possible product contaminants. Compatible with all standard LPG pressure vessels with NPT couplings.

** Flow rates are shown for bare relief valves, pipe-aways will reduce flow | *** Per NFPA 58, table 5.7.2.5 area shown is for UL or ASME flow rating,which ever is greater | Viton® and Kalrez® are trademarks of DuPont Performance Elastomers.

FEATURES: • Durable single piece anodized aluminum or

brass forged body• Stainless steel internal components• Standard Seal Material: HNBR• Available Seal Material: Viton or Kalrez

• Custom start-to-discharge settings available upon request

• Non-adjustable, tamper resistant design

• Outlet thread accepts MEP178 pipeaway for 2” FNPT pipeaway

• Includes plastic weather cap for relief valve outlet

MEV125/250(Aluminum)

MEV125B/250(Brass)


65 66

DD

Start-to- UL Flow Capacity Accessories

Item No. Container Container Seal Discharge SCFM/Air**

Application

Protective Relief Discharge Vents Type Connection Material* Setting Per CGA S1.1

Cap Valve 45° 90°

PSIG @ 480 PSIG Plug Angle Angle

MEV75FIR* DOT 3/4” MNPT Viton® 375 368 LPG MEP175C MEP175P MEP175-45 MEP175-90

RELIEF VALVES RELIEF VALVESSemi Internal Pressure Relief Valves MARSHALL EXCELSIOR

* Seat Material not UL Listed | ** Flow rates are shown as bare relief valves | *** Size relief capacity per NFPA 58 2011, table 5.7.2.6 | Viton® and Kalrez® are trademarks of DuPont Performance Elastomers NOTE: For stainless steel add “S” to part to part number - i.e. MEV200SSIR/265

Semi Internal Pressure Relief Valves are designed for use in large stationary LPG containers as a primary pressure relief valve. These pressure relief valves have been specifically designed to provide optimum performance when installed in either a 2” half or full coupling making them perfect for most large stationary tank installations.

• Durable forged brass body with 3” NPT outlet pipe-away thread

• All steel and stainless steel stem, spring, and valve gasket holder for maximum

corrosion resistance• Custom set pressures available

• Available with Nitrile, Viton®, or Kalrez® valve seals

• Large seating surface for superior seal performance and reliability

• Available with 125, 250, 265 PSI UL Listed set pressures

FEATURES:

MEV200SIR

Full Internal Pressure Relief Valves are designed for use on forklift cylinders and other DOT removable cylinders up to 122 pounds of LP-Gas capacity. The working components of this valve are located inside the tank reducing possible malfunction caused by outside debris or other foreign materials.

NOTE: NFPA #58 states, “All containers used in industrial trucks (including fork lift truck cylinders)service shall have the container pressure relief valve replaced by a new or unused valve within12 years of the date of manufacture of the container and every 10 years thereafter.”

DOT Full Internal Pressure Relief Valve MARSHALL EXCELSIOR

* UL Listed in accordance with Compressed Gas Association Pamphlet S-1.1, Pressure Device Standard for Cylinders; Meets requirements for use on DOT containers with 242 lb. or less weight of water or 122 lb. or less of LP-Gas | ** Flow rates are shown for bare relief valves, pipe-aways will reduce flow | Viton® is a trademark of DuPont Performance Elastomers

MEV75FIR

MEP175-90MEP175-45

MEP175C

Item No.STD

Setting(PSIG)

ContainerConnection

InstallationHex

Flow CapacitySCFM/Air ** Tank Surface

Area (Sq. Ft.)PipeawayAdapterUL @ 120%

Set Pressure

MEVS-UVE445AM/250 250 1” MNPT 1-5/16” 987 35 MEPS-445-21

MEVS-PVE445AT/375* 375 1” MNPT 1-5/16” 1625 64 MEPS-445-21

1-1/4” & 2-1/2” NPT External Pressure Relief Valves MARSHALL EXCELSIOR

MEVS-445AT is classified by Underwriters Laboratories Inc. in accordance with CGA Pamphlet S-1.1. | ** Flow rates are shown as bare relief valves

• Used as pressure relief device on larger ASME engine fuel containers and recreational vehicle containers

• Use MEVS-PVE445AT on multiport 420-lb. DOT containers

FEATURES: • Protective cap MEPS-UEP16 included• Supplied with Everseal™ pre-applied thread

sealant

MEVS-UVE445A Series

Figure 1

Dimensions (Approx.) - see Fig. 1A B C D Hex

5-9/16” 1-3/32” 3-15/32” 1-5/16”

Item No.Container

ConnectionMNPT

PipeawayMNPT

SealMaterial*

Start-to-Discharge

SettingPSIG

WrenchHex


ApplicationAccessories

LPG NH3

MEV200SIR/125

2” 3”

Nitrile 125

3-1/2”

4,870

YES

NO

MEV200SIR-106(Cap & Lanyard)

MEP104-24(Pipeaway adapter)

see page 104

MEV200SIR/250 Nitrile 250 10,925 NOMEV200SSIR/250 Nitrile 250 10,925 YESMEV200SIR/265 Nitrile 265 11,475 NOMEV200SSIR/265 Nitrile 265 11,475 YESMEV200SIRV/125 Viton® 125 4,870 NOMEV200SIRV/250 Viton® 250 10,925 NOMEV200SSIRV/250 Viton® 250 10,925 YESMEV200SIRV/250 Viton® 250 10,925 NOMEV200SSIRV/250 Viton® 250 10,925 YESMEV200SIRK/125* Kalrez® 125 4,870 NOMEV200SIRK/250* Kalrez® 250 10,925 NOMEV200SSIRK/250* Kalrez® 250 10,925 YESMEV200SIRK/265* Kalrez® 265 11,475 NOMEV200SSIRK/265* Kalrez® 265 11,475 YES

MEV200SSIR


67 68

DD Container Flow Capacity

Service

Seat

Accessories

Item No. STD/PSIG Connection

SCFM/Air** Material UL @ 120% Set Pressure LPG NH3 Cap

MEV300FIR-3F/250 250 10,865 Yes NitrileMEV300FIR-3F/265 265 11,600 Yes NitrileMEV300FIRV-3F/250 250

3” 300 lb. Flange 10,865

Yes No Viton®

MEV300FIRV-3F/265 265 11,600 No Viton®

MEV300FIRK-3F/250* 250 10,865 Yes Kalrez® ~MEV300FIRK-3F/265* 265 11,600 Yes Kalrez® ~

MEV300FIR-09

RELIEF VALVES RELIEF VALVES

Flanged Full Internal Pressure Relief Valves are for use in mobile LPG and NH3 containers as a primary pressure relief valve for bobtail and transport trailer installations. All working componentsare internal to the container connection preventing damage to the valve should a roll-over incidentoccur. Marshall Excelsior’s unique design incorporates a standard 3” ANSI - 300 lb. raised face flange connection to assure a 100% leak free connection for rugged over-the-road applications.This eliminates problems associated with NPT threaded connections and/or tank coupling weardue to vibration from over-the-road transit, providing maximum tank and relief valve service life.

Flanged Full Internal Pressure Relief Valves MARSHALL EXCELSIOR

* Seat Material not UL Listed | ** Flow rates are shown for bare relief valves | *** Size relief capacity per NFPA 58 2011, table 5.7.2.6 | ~ Recommendedfor LPG and NH3 dual service applications | Viton® and Kalrez® are trademarks of DuPont Performance Elastomers

FEATURES: Marshall Excelsior’s FlangeFull Internal Pressure Relief Valves have the same features as their Full Internal Pressure Relief Valves above.

MEV300FIR-3F

* Seat Material not UL Listed | ** Flow rates are shown for bare relief valves, pipe-aways will reduce flow | *** Size relief capacity per NFPA 58 2011, table 5.7.2.6 | ~ Recommended for LPG and NH3 dual service applications

Full Internal Pressure Relief Valves MARSHALL EXCELSIOR

Full Internal Pressure Relief Valves are for use in mobile LPG and NH3 containers as a primary pressure relief valve for bobtail and transport trailer installations. All working components are internal to the container connection preventing damage to the valve should a roll-over occur.

• Stainless steel body construction• All stainless steel internal components for

maximum corrosion resistance• Nitrile, Viton®, or Kalrez® seals available

• Large seating surface for superior seal performance and reliability

• 250 and 265 PSI set pressures available• Custom set pressures available

FEATURES:

MEV200FIR/MEV300FIR

Item No. STD/PSIG

ContainerConnection

InstallationHex

Flow CapacitySCFM/Air**

UL@120% Set Pres.

ServiceSeat

Material

Acessory

LPG NH3 Cap Hex Installation Tool

MEV200FIR/250 250

2”MNPT 1-1/2” 4,460

Yes

Yes Nitrile

MEV200FIR-09 MEP200FIR

MEV200FIR/265 265 Yes NitrileMEV200FIRV/250 250 No Viton®

MEV200FIRV/265 265 No Viton®

MEV200FIRK/250* 250 Yes Kalrez®~MEV200FIRK/265* 265 Yes Kalrez®~MEV300FIR/250 250

3”MNPT 2-1/2”

10,865 Yes Nitrile

MEV300FIR-09 MEP300FIR

MEV300FIR/265 265 11,600 Yes NitrileMEV300FIRV/250 250 10,865 No Viton®

MEV300FIRV/265 265 11,600 No Viton®

MEV300FIRK/250* 250 10,865 Yes Kalrez®~MEV300FIRK/265* 265 11,600 Yes Kalrez®~

Semi-Internal Pressure Relief Valves MARSHALL EXCELSIOR

Item No. STD/PSIG

ContainerConnection

InstallationHex

Flow CapacitySCFM/Air** Tank Surface

Area (Sq. Ft.)Replacement

Rain CapUL@120% Set Pres.

MEVS-UVE433AM/250 250 3/4” MNPT 1-1/16” 1,930 79

MEPS-433-45A

MEVS-UVE433AC/275* 275 3/4” MNPT 1-1/16” 1,709 68MEVS-UVE443AM/250 250 1” MNPT 1-7/8” 2,755 122MEVS-UVE443AC/275* 275 1” MNPT 1-7/8” 2,436 105MEVS-UVE453AM/250 250 1-1/4” MNPT 2-7/16” 4,640 230MEVS-UVE453AC/275* 275 1-1/4” MNPT 2-7/16” 4,406 216

* California setting 275 psig | ** Flow rates are shown for bare relief valves | NOTE: Size relief capacity per NFPA58, table 5.7.2.6

Semi-Internal Pressure Relief Valves are for used as a pressure relief device on stationary ASME containers and domestic tanks.

• Durable all brass body• Sturdy construction; made with

non-corrosive internal materials• Furnished with rain/dust cap for protection

against contamination

• Rain cap also available separately• Supplied with Everseal™ pre-applied thread

sealant

FEATURES:

MEVS-UVE443A

MEPS-433-45ARain/Dust cap with lanyard tominimize cap loss. Protects

against contamination.

Universal Relief Valve Covers MARSHALL EXCELSIOR

Item No. Description ApplicationLPG

MEH502 Adjustable Relief Valve Cover 1/2” to 3/4”Yellow Vinyl

MEH503 Adjustable Relief Valve Cover 3/4” to 1-1/4”

MEH503

MEH502Semi-Internal Pressure Relief Valves are for used as a pressure relief device on stationary ASME containers and domestic tanks.

• Durable all brass body• Sturdy construction; made with

non-corrosive internal materials• Furnished with rain/dust cap for protection

against contamination

FEATURES:

MEVS-UVE433A MEVS-UVE453A


69 70

D

Item No. Container Start-to-Discharge UL* Flow ASME* Flow Wrench

Connection Setting PSIG capacity SCFM/AIR capacity SCFM/AIR Hex Flat

66.1127 1” NPT 375 1,491 — 1-5/16”66.1128 3/4” NPT 250 2,007 1,807 1-9/16”66.1129 1” NPT 250 2,757 2,493 1-3/4”66.1130 1-1/4” NPT 250 4,312 3,913 2-1/4”66.1242** 1” NPT 312 109 979 1-5/16”66.1135** 1” NPT 250 864 78 1-5/16”66.1162 3/4” NPT 312 690 690 11/16”

Item No. Container Start-to-Discharge UL (at 120% of Set Pressure) Wrench

Connection Setting (PS) Flow Capacity SCFM/AIR Hex Flat

66.1027 3/4” NPT 375 400 1-1/16”

66.0248

Valve Item No. Cap Item No.

66.1128 10.0.950.0203 66.1129 10.0.950.0204 66.1130 10.0.950.0205 66.1135 10.0.110.5032 66.0248 30.0.110.0278 66.1242 30.0.110.0277

Seal

Start-to- Inlet

Accessory Item No.

Body

Material Discharge

MNPT A B C D Pipe-away

Material

Setting PSIG Adapter

MEH225 Brass Nitrile 440 1/4” 1-1/16” 13/16” 1/4” 9/16” Hex —MEH225SS/350 Stainless Steel Nitrile 350**** 1/4” 1-1/16” 13/16” 1/4” 9/16” Hex —MEH225SS/400 Stainless Steel Nitrile 400 1/4” 1-1/16” 13/16” 1/4” 9/16” Hex —MEH225SS Stainless Steel Nitrile 440 1/4” 1-1/16” 13/16” 1/4” 9/16” Hex —MEH25/450 Brass Nitrile 450 1/4” 1-59/64” 1-43/64” 1/4” 7/8” Hex MEP173*MEH25K/450 Brass Kalrez® 450 1/4” 1-59/64” 1-43/64” 1/4” 7/8” Hex MEP173*MEH25V/450 Brass Viton® 450 1/4” 1-59/64” 1-43/64” 1/4” 7/8” Hex MEP173*MEH50/460 Brass Nitrile 460 1/2” 2-1/2” 2-1/8” 3/8” 1-1/8” Hex MEP174**MEH75/460 Brass Nitrile 460 3/4” 2-21/32” 2-5/32” 1/2” 1-1/8” Hex MEP174**MEJ602H*** Brass Nitrile 440 1/4” — — — — —

External Pressure Relief Valves CAVAGNA GROUP

66.1139 Pressure Relief Valves are designed for small containers and on-line pipe installations.Setting point: 250 PSIG.

66.1140 Pressure Relief Valves are for small containers and on-line pipe installations. Setting point: 375 PSIG.

Bottom Male

Wrench Grip

Thread PRV - Start to PRV-OVERPRESSURE 10% PRV Item No.

Connection

Hexagon Type Discharge CAPACITY Nm3/min. Approval Orifice

(mm) Setting (PSIG) (If not specified otherwise) (mm)

66.1139 - PRV 1/4” - 18 NPT 22 Taper 250 18.41 (at 120% O.P.SCFM-AIR) UL/ASME 19.0066.1140 - PRV 1/4” - 18 NPT 22 Taper 375 33.52 (at 120% O.P.SCFM-AIR) UL 19.0070.0073 - EU19 3/4” NPT — Taper 250 1808 (at 20% O.P.SCFM-AIR) UL/ASME —

66.1139

MEH75 MEH50 MEH25

RELIEF VALVES RELIEF VALVES

D

Cavagna’s Internal Pressure Relief Valves for ASME and DOT Containers are designed specificallyfor use as a primary pressure relief device on ASME containers up to 2,000 gallon water capacity.Furnished with rain cap for protection against contamination. See ordering information for partnumbers. All these valves have a pre-applied sealant on the container connection. All these valves are ASME approved.

Internal Pressure Relief Valves for ASME and DOT Containers CAVAGNA GROUP

*(at 120% of set pressure) | **Fully internal

Internal Pressure Relief Valve 66.1027 for DOT Fork Lift Cylinders are designed specifically for use as primary relief valve on fork lift cylinders. A 45° deflector adapter is already included into the body of the valve. The design of the valve is a one-piece hot forged brass body.

Internal Pressure Relief Valve 66.02487 for DOT Fork Lift Cylinders are designed specifically for use as primary relief valve on fork lift cylinders.

Internal Pressure Relief Valves for DOT Fork Lift Cylinders CAVAGNA GROUP

66.1128 66.1129

66.113566.113066.1162 Rain Cap

66.1027

66.1027

* 1/4” FNPT Outlet | ** 1/2” FNPT Outlet | *** Factory Installed Vent Valve | **** Special Applications

• Compact design to fit any application• Stainless steel spring• Non-adjustable, tamper resistant design• Stainless steel models rated for LP-Gas

and NH3

• Designed to increase flow at discharge

FEATURES:

Hydrostatic Pressure Relief Valves are designed to protect piping and shutoff valves fromoverpressure situations where liquid LP-Gas or NH3 has the potential to be trapped. Valves provide pressure relief and protect against line or plumbing system failures.

MEH225SS MEP173

Hydrostatic Pressure Relief Valves MARSHALL EXCELSIOR

70.0073 66.1140


71 72

DD


Standard Spring Range*

ME840-10-125 1-1/4” FNPT High Flow Bypass Valve 90-125 PSIME841-10-125 1-1/4” Socket Weld High Flow Bypass Valve 90-125 PSIME840-12-125 1-1/2” FNPT High Flow Bypass Valve 90-125 PSIME841-12-125 1-1/2” Socket Weld High Flow Bypass Valve 90-125 PSIME840-16-125 2” FNPT High Flow Bypass Valve 90-125 PSIME840C-16-125 2” FNPT Classic Flow Bypass Valve 90-125 PSIME841-16-125 2” Socket Weld High Flow Bypass Valve 90-125 PSIME840-125 1-1/4” - 2” Universal High Flow Bypass without Flanges 90-125 PSI

High Flow Bypass Valves for Dispensing Applications MARSHALL EXCELSIOR

These Marshall Excelsior Valves are intended for use in small cylinder filling applications as abypass and primer valve for turbine style dispensing pumps. These bypass valves feature aspecial “check ball” mechanism that helps eliminate vapor from liquid while keeping the pumpflooded and properly primed. The priming and vapor elimination features, in combination with the high flow bypass design, significantly reduces pump wear and promotes seal longevity.

• Ductile iron body and bonnet construction• Large range of set pressure springs• Two 1/4” FNPT plugged auxiliary pressure

ports (outlet side)• Stainless steel main valve poppet

FEATURES: • Heavy duty protective stem cap• Available in 3/4” and 1” FNPT threaded versions• Factory set at 125 PSI• Durable powder coat finish

BYPASS VALVES

* Alternate spring ranges available.

High Flow 3” Bypass Valve for Plant Applications MARSHALL EXCELSIOR

The 3” Bypass Valve is specifically designed for plant systems where maximum bypass flowis necessary to protect the pump from rapid pressure changes or over pressurization. Perfectlysuited for 4” base mount pumps or larger pump applications.

• Ductile iron body and bonnet construction• All stainless steel internal wetted components• Bonnet/seat positioned at 35° angle for

maximum product flow• Downstream bleed port to boost product

flow during bypass

FEATURES: • Two 1/4” FNTP plugged auxiliary pressure ports• Heavy duty protective stem cap• Factory set at 100 PSI• Durable powder coat finish


BYPASS VALVES

ME840-6/150

ME840-24/100

Bypass Valves for Bobtail Truck/Plant Applications MARSHALL EXCELSIOR

*Alternate spring ranges available

Marshall Excelsior’s High Flow Bypass Valves for Bobtail Truck/Plant Applications are specificallydesigned to protect truck and plant pumps from damage due to excessive pressure whileproviding the industry’s best bypass flow rates across a full range of set pressures. They featurewide open flow channels with an orifice weep hole chamber to prevent the valve from slammingopen/closed. The weep hole chamber also helps prevent valve seat chatter by allowing constantpressure communication between both the upstream and downstream side of the seat.

• All ductile iron body and bonnet

• All stainless steel wetted component• Heavy duty protective stem cap• Wide open flow channels for industry best

flow rates• Orifice weep hole to maintain constant

pressure above and below valve seat• Large range of set pressure springs• Zinc dichromate finish for maximum corrosion resistance

• Weldable steel NPT and socket weld flanges• Available with or without flanges factory

assembled• Flanges available 1-1/4” through 2” NPT

and socket weld construction• Universal 4 bolt, flanged body configuration• Two 1/4” FNPT plugged auxiliary pressure

ports• Factory set at 125 PSI

FEATURES:

ME840-16/125

ME840-16-104

ME840C-16-104

Item No. Description Standard Spring Range*ME840-24-100 3” FNPT High Flow Bypass Valve 0-100 PSIME840-24-200 3” FNPT High Flow Bypass Valve 0-200 PSI

Item No. Description Standard Spring Range*ME840-6-150 3/4” FNPT High Flow Bypass Valve 50-150 PSIME840-8-150 1” FNPT High Flow Bypass Valve 50-150 PSI

ME840-8-150

Stainless SteelIntegral Check

Ball Seat


73 74

DD


Standard Spring Range*

ZV200 2” NPT Low Pressure Build-up Bypass Valve 41-150 PSI

Item No. Inlet Outlet Slip-on Weld Flange Differential Pressure Range PSI

B166 3/4”, 1” 3/4”, 1” No 25 – 225 (1.7 - 15.5)

Item No. Inlet Outlet Slip-on Weld Flange Differential Pressure Range PSI

T166 1-1/4”, 1-1/2” 1-1/4”, 1-1/2” No 25 - 225 (1.7 - 15.5)

Maximum Rated Flow* - GPM (L/min) @ Item No.

Ports 20 PSI 50 PSI 80 PSI 120 PSI

(1.38 Bar) (3.45 Bar) (5.52 Bar) (8.27 Bar) BV0.75 3⁄4” NPT Tapped

25 (95) 40 (151) 50 (189) 60 (227)

BV1 1” NPT Tapped BV1.25 1-1/4” NPT Tapped

60 (227) 80 (303) 100 (379) 125 (473)BV1.5 1-1/2” NPT Tapped BV2 2” NPT Companion Flanges** 150 (568) 180 (681) 220 (833) 250 (946)

Corken’s Low Pressure Build-up Bypass Valves are specifically designed for applications requiringprotection for positive displacement pumps. The valves protect pumps with capacities up to 250 GPM (946 L/min). The continuous internal bleed will assist in the operation of systems with“air” or “electric” operated internal valves, equalizing pressure. Typical applications include bobtail, transport and stationary loading and unloading of LPG, NH3 and other light liquids.

• All ductile iron body

• Flow rates up to 250 GPM (946 L/min) at 120 PSI (8.3 bar) differential

• Multiple spring options to select required pressure for truck or stationary application

• Multiple flange options: 1-1/4”, 1-1/2”, 2”, 2-1/2” NPT and weld flanges

• Dual inlet and outlet gauge openings• No unions necessary for installation

FEATURES:

Automatic Dual-Purpose, Bypass Valves are typically used for cylinder filling pumps and aerosolpropellant feed pumps. The valves are a combination bypass and priming valve specificallydesigned for small cylinder-filling-type pumps, especially of the regenerative turbine type, suchas the Corken Coro-Flo® pump series with flows up to 40 GPM (9.1 m3/hr). The patented vaporelimination system keeps liquefied gas pumps primed to increase system reliability and decreasepump and seal wear. The B166 is a smooth operating bypass with moderate pressure buildup.

Pump Flow Control Valves are typically used for large-capacity pumps filling variable size tanksand bottles such as those used with delivery trucks or multiple cylinder filling plants. A high-pressure build-up valve for smooth acting flow control. The T166 is specifically designed for bypass protection for pumps in the 30 - 100 GPM (6.8 - 22.7 m3/hr) range, such as those used on delivery trucks. In contrast to the B177, the T166 valve opens gradually as pressure builds upto modulate the flow, bypassing the excess capacity smoothly and silently back to the supply tank. A continuous internal bleed in this valve assists in eliminating vapors.

Bypass Valve CORKEN

Automatic Dual-Purpose, Bypass Valve CORKEN

Pump Flow Control Valve CORKEN

BYPASS VALVES BYPASS VALVES

ZV200

B166

T166

*Alternate spring ranges available

High Flow Maximum Flow Through Bypass Valves BLACKMER

Blackmer Bypass Valves provide exceptionally close pressure control, even under widely varyingbypass flow conditions. They are designed to protect pumps and system components fromexcessive pressure damage, and no LP gas pump installation is complete without one. The valves do not have small, easily plugged, sensing passages; and with only two moving parts, their operation is simple and reliable. They open precisely at the preset spring pressure, and theyclose smoothly and quietly, thanks to a patented dash-pot design. A small chamber in the valvestem fills with liquid when the valve opens. This liquid then provides a hydraulic cushion preventing the valve from slamming shut if pressure is suddenly released. It also minimizes chatter and valve seat wear when pressures hover around the crucial limit.

*Normal maximum bypass flow rates without significantly exceeding the set pressure limit | ** 1-1⁄4 inchand 1-1⁄2-inch NPT and WELD bolt-on flanges are available

BV0.75 and BV1 Bypass Valves• Used for cylinder-filling system• May be used with 1-1/4” or 1-1/2” Blackmer pump models

BV1.25 and BV1.5• Used for bobtail trucks and smaller bulk

plant systems• May be used with 2” or 3” Blackmer pump models

BV2• Used for transports or larger bulk plant systems• PSI is set at 125• Recommended for use with 3” and 4”

Blackmer pump models

BV.075 / BV1

Bypass/Pressure Relief Valve BLACKMER

Item No. Porting Max. FlowsRV18 DN 25/1” flanged ANSI 300 screwed NPT(F) 200 L/min (52.83 gpm)RV19 DN 38/1-1/2” flanged ANSI 300 screwed NPT(F) 600 L/min (158.5 gpm)

The Ebsray Bypass/Pressure Relief Valves are specifically designed for a wide variety of industrial services. The easily adjustable differential-pressure settings provide accurate and repeatable performance that enables full pump flow while maintaining controlled preset maximum pressure.

Features & Benefits• 90º porting arrangement• Flanged ANSI Class 300 or threaded (NPT)

ports available for most models• Adjustable pressure setting within spring

range for optimum dispensing flow rates• Low pressure rise• Pressure Casings: Ductile iron to ASTM A395• Elastomers - Viton® – as standard

• Diff. pressures to 14 bar (200 psi)• Hydrostatic test pressure: 70 bar (1,016 psi)

Optional valve types-application dependent:• CBS - Constant Bleed System• VRS - Vapour Removal System• NRV - Non-Return Valve

RV Series


75 76

DD

Item No. Inlet Outlet Slip-on weld flange Differential Pressure Range PSI

B177 1-1/4”, 1-1/2” 1-1/4”, 1-1/2”

No 20-160

2”, 2-1/2” 2”, 2-1/2” (0.7-11)

BYPASS VALVES

ME880 Series

ME880S Series

ME882S Series

B177

Differential Bypass Valves are typically used in liquefied-gas bulk-plant installations for loading and unloading pumps. The B177 is a low-pressure build-up bypass valve specifically designed for applications requiring protection for positive displacement pumps in the 40 - 350 GPM (9.1- 79.5 m3/hr) range. It can also be used as a differential back-pressure valve to assure adequatepressure on meters, etc. To function properly, this valve requires a pressure sensing line from the storage tank.

Differential Bypass Valve CORKEN

Excess Flow Valves MARSHALL EXCELSIOR

EXCESS FLOW VALVES

Marshall Excelsior’s Excess Flow Valves in the industry. These valves are used in liquid or vapor LP-Gas or NH3 systems as well as for filling, withdrawal and vapor equalization in containers or line applications, specifically long lines or branch piping. This product protects against excessive discharge as a result of a break in the hose or piping system. The excess flow feature remains closed after activation until the system pressure equalizes on both sides of the shutoff poppet.

WARNING: An excess flow valve will not activate if there is a break or leak downstream of the valve that does not equal or exceed the closing flow of the valve or if the excess flow valve installed exceeds the flow capacity of the system. (For more information: www.marshallexcelsior.com)

• Integral breakaway feature leaves valve assembly intact with internal hex broach for easy removal• All stainless steel internal components

FEATURES:

Liquid Butane Capacity = Flow Rate x .94 | Liquid Anhydrous Ammonia Capacity = Flow Rate x .90

Item No. InletMNPT Porting Closing Flow

GPM PropaneBrass Steel* Stainless Steel*ME880-4/1.8 — — 1/4” 1/4” 1.8ME880-6/4.6 ME880S-6/4.6 ME880SS-6/4.6 3/4” 3/4” 4.6ME880-6/14 ME880S-6/14 ME880SS-6/14 3/4” 3/4” 14ME880-6/17 ME880S-6/17 ME880SS-6/17 3/4” 3/4” 17ME880-6/22 ME880S-6/22 ME880SS-6/22 3/4” 3/4” 22ME880-6/28 ME880S-6/28 ME880SS-6/28 3/4” 3/4” 28ME880-10/32 ME880S-10/32 ME880SS-10/32 1-1/4” 1-1/4” 32ME880-10/42 ME880S-10/42 ME880SS-10/42 1-1/4” 1-1/4” 42ME880-12/95 — — 1-1/2” 1-1/2” 95ME880-16/80 ME880S-16/80 ME880SS-16/80 2” 2” 80ME880-16/105 ME880S-16/105 ME880SS-16/105 2” 2” 105ME880-16/114 ME880S-16/114 ME880SS-16/114 2” 2” 114ME880-16/140 ME880S-16/140 ME880SS-16/140 2” 2” 140

— ME882S-16/80 — 2” 2” MNPT 80— ME882S-16/105 — 2” 2” MNPT 105— ME882S-16/114 — 2” 2” MNPT 114— ME882S-16/140 — 2” 2” MNPT 140— ME880S-24/265 — 3” 3” 265— ME880S-24/350 — 3” 3” 350— ME882S-24/265 — 3” 3” MNPT/2” FNPT 265— ME882S-24/350 — 3” 3” MNPT/2” FNPT 350

Internal Hex Broach

EXCESS FLOW VALVESExcess Flow Valves Excela-Flange Series MARSHALL EXCELSIOR

Item No. Description Material ClosingFlow

MatingFlange Type

Weight(lbs.)

ME883S-16/80

Excela-Flange 2” MNPT x 4 Bolt Type A Flange Excess Flow Ductile

80

B 4.23ME883S-16/105 105

ME883S-16/114 114

ME883S-16/140 140

**WARNING - Reducing outlet pipe size below 2” nominal diameter could result in excess flow feature failing to close as designed | Liquid Butane Capacity = Flow Rate x .94 | Liquid Anhydrous Ammonia Capacity = Flow Rate x .90

Marshall Excelsior offers the largest closing flow selection in the industry. These excess flow valves are intended for use in liquid or vapor LP-Gas or NH3 systems. These valves can be used for filling, withdrawal and vapor equalization in containers or line applications, specifically long lines or branch piping. This product is designed to protect against excessive discharge as a result of a break in the hose or piping system. The excess flow feature is designed to remain closed after activation until the system pressure equalizes on both sides of the shutoff poppet.

The ME883S-16 Series valves feature our new modular Excela-flange 4 bolt inlet flange design that can be easily adapted to both NPT thread or socket weld type B companion flanges ranging from 1-1/4” to 2” in diameter making it universal to piping sizes within this range. This innovative system allows installers the ability to eliminate unnecessary extra connections as well as possible leak points by integrating a convenient 4 bolt flange union at the valve inlet.

• All models feature stainless steel stem, spring and valve guide

• Valve body: Ductile Iron/Shutoff poppet assembly: zinc plated steel and stainless steel

• Available 2” NPT x 4 Bolt Type A Flange

• All models can be used with LP Gas or NH3

• Available in a wide variety of closing flow rates

FEATURES:


MEP873 4 Bolt Type A Flange Valve Installation Tool with 1” Square Drive

MEP183-102 Replacement Torque Posts

ME883S-16/1052” NPT x 4 Bolt Flange

Excess Flow Valve

MEP873


77 78

DD

Inlet

Outlet

Wrench

Approximate Closing Flows Item No. Material

Connection

Connection

Hex Flats Liquid 25 100

(GPM Propane) PSIG Inlet PSIG Inlet

6901900036 Steel 1-1/4” 1-1/4” 1-7/8” 55 10,600 18,9206901900037 Steel 1-1/4” 1-1/4” 1-7/8” 55 3,830 6,760

Inlet

Outlet

Wrench

Approximate Closing Flows Item No. Material

Connection

Connection

Hex Flats Length Liquid 25 100

(GPM Propane) PSIG Inlet PSIG Inlet

6902900127 Steel 1-1/4” 1-1/4” 2” 1-5/16” 30 5,750 9,8006902900128 Steel 1-1/4” 1-1/4” 2” 1-5/16” 40 7,500 13,3306902900129 Steel 1-1/4” 1-1/4” 2” 1-5/16” 50 8,800 15,970

Cavagna Excess Flow Valves are designed for liquid or vapor fill/withdrawal and for vapor equalization in containers or line applications. They are intended to close when the liquid or vaporpassing through the hose or the piping system exceeds the prescribed flow rate. Valves are available in different sizes and body configurations.

Once the flow exceeds the valve’s setting, the valve closes and will remain closed until the system equalizes. Once the pressure on both sides of the poppet is equal, a built-in equalizingpassage automatically opens the valve.

Excess Flow Valve for Liquid or Vapor CAVAGNA GROUP

Excess Flow Valve for Liquid or Vapor Withdrawal CAVAGNA GROUP

Excess Flow Valves for Liquid or Vapor Withdrawal are designed to be mounted on the bottom ofstorage tanks for liquid service. They may also be mounted on the top for vapor service.

BACK CHECK VALVES

Excess Flow Valve

Excess Flow Valves

EXCESS FLOW VALVES

*Rated for LP-Gas & NH3 | **Includes removable o-ring

High Flow Back Check Valves MARSHALL EXCELSIOR

Marshall Excelsior’s Back Check Flow Valves lead the industry with up to 20% more flow than the nearest competitor. These valves provide flow protection to container openings or liquid lineswhere flow is intended for one direction. The valve is normally closed until pressure activates the valve when flow is directed into piping or containers causing the back check to open. Whenflow stops or reverses, the check returns to the closed position.

These valves come with dual seating capabilities or an optional bonded soft seat on 2 and 3” models. With the dual seating capabilities, the factory installed O-ring provides a leak-free, soft seat seal which enables repair and maintenance to be done on depressurized plumbing. Remove the O-ring to allow metal-to-metal seating with a minimal leak seal to restrict flow in case of a break in the line.

NOTE: Leaving the O-ring soft seat installed on the valve will require a minimum of 15 PSIG pressure differential between the transfer line and container to unseat the valve and allow it to fully open.

• Up to 20% More Flow than nearest competitor

• Maximum flow achieved by full port and increased stem travel design

• All stainless steel internal components

FEATURES: • Integral breakaway feature leaves valve

assembly intact with internal hex broach for easy removal

• Dual purpose seat reduces inventory from 2 to 1

ME870 SeriesShown with O-ring Soft Seat

ME870S SeriesShown with O-Ring

Removed for Metal-to-Metal Seat

ME870SBN-24Shown with Bonded Soft Seat

ME872S-16

Item No.Inlet FNPT Outlet

MNPTPropane Flow @ 10 PSIG

Pressure DifferencialBrass Steel* Stainless Steel*ME870-6 ME870S-6 ME870SS-6 3/4” 3/4” 24ME870-10 ME870S-10 ME870SS-10 1-1/4” 1-1/4” 61ME870-12 — — 1-1/2” 1-1/2” 112ME870-16 ME870S-16 ME870SS-16 2” 2” 187

— ME872S-16 — 2” MNPT 2” 187— ME870S-24 — 3” 3” 449— ME872S-24 — 2” FNPT/ 3” MNPT 3” 449— ME872S-24SP** — 2” FNPT 3” 449

*Rated for LP-Gas & NH3 | **Includes removable o-ring | Liquid Butane Capacity = Flow Rate x .94 | Liquid Anhydrous Ammonia Capacity = Flow Rate x .90

High Flow Back Check Valves with Bonded Soft Seat MARSHALL EXCELSIOR

Item No.Inlet FNPT Outlet

MNPTPropane Flow @ 10 PSIG

Pressure DifferencialBrass Steel* Stainless Steel*— ME870SBN-10 — 1-1/4” 1-1/4” 61— ME870SBN-16 — 2” 2” 187— ME872SBN-16 — 2” MNPT 2” 187— ME870SBN-24** — 3” 3” 449— ME872SBN-24 — 2” FNPT/ 3” MNPT 3” 449— ME872SBN-24SP — 2” FNPT 3” 449


79 80

DD

Propane Flow Item No. Description Differential Pressure 10 PSI 25 PSI 50 PSI ME869-10/10 1-1/4” MNPT x 2-1/4” M. Acme 75 116 157ME869-10/8 1-1/4” MNPT x 1-3/4” M. Acme 51 85 124ME869-16 2” MNPT x 3-1/4” M. Acme 195 296 416ME869-24 3” MNPT x 3-1/4” M. Acme 347 519 718

BACK CHECK FILL VALVESBACK CHECK VALVES

• Primary seat creates metal-to-metal seating surface• Secondary seat is bonded Nitrile soft seat

for a leak free seal• Up to 20% more flow than nearest competitor

FEATURES: • Maximum product flow achieved by full

port and stem travel design• Stainless steel stem, spring and valve guide in body check assembly• Built-in hydrostatic relief valve• ONLY for use with LP Gas

High Flow Double Back Check Fill Valves MARSHALL EXCELSIOR

High Flow Double Back Check Valves provide back flow protection to container openings or liquidlines where flow is intended in one direction. The valve is normally held closed until pressure activates the valve when flow is directed into piping or containers causing the double back checkto open. When flow stops or reverses, both checks return to the closed position. All MEC HighFlow Double Back Check Valves are supplied with the correct ACME cap and chain assembly, as well as factory installed hydrostatic relief protection.

ME869-16

ME869-24

Liquid Butane Capacity = Flow Rate x .94 | Liquid Anhydrous Ammonia Capacity = Flow Rate x .90 | Replacements o-rings available upon request. See Replacement Parts section.

The ME873S Series valves feature our new modular Excela-flange 4 bolt inlet flange design that can be easily adapted to both NPT thread or socket weld type B companion flanges ranging from 1-1/4” to 2” in diameter making it universal to piping sizes within this range. This system allows installers to eliminate unnecessary connections as well as possible leak points by integrating a convenient 4 bolt flange union at the valve inlet. These valves provide back flow protection to container openings or liquid lines where flow is intended for one direction. The valve is normally held closed until pressure activates the valve when flow is directed into piping or containers causing the back check to open. When flow stops or reverses, the check returns to the closed position. All MEC High Flow Back Check valves are supplied with o-ring soft seats, which can be removed for metal to metal seating.

High Flow Back Check Valves - Excela-Flange Series MARSHALL EXCELSIOR

Item No. Description Material Propane Flow @10 PSIG Pres. Dif.

Mating Flange

Weight(lbs.)

ME873S-10 Excela-FlangeTM 1-1/4” MNPT x 4 Bolt Type A Flange Back Check Valve

Ductile

61

B

4.1ME873SBN-10 Excela-FlangeTM 1-1/4” MNPT x 4 Bolt Type A Flange Back Check Valve (SBN) Bonded Seat 61 4.1ME873S-16 Excela-FlangeTM 2” MNPT x 4 Bolt Type A Flange Back Check Valve 187 4.2ME873SBN-16 Excela-FlangeTM 2” MNPT x 4 Bolt Type A Flange Back Check Valve (SBN) Bonded Seat 187 4.2ME873S-24 Excela-FlangeTM 3” MNPT x 4 Bolt Type A Flange Back Check Valve 449 7.0ME873SBN-24 Excela-FlangeTM 3” MNPT x 4 Bolt Type A Flange Back Check Valve (SBN) Bonded Seat 449 7.1

• Universal seat - Remove O-ring seal to create metal to metal seating surface or (SBN) bonded seat

• Up to 20% MORE FLOW than nearest competitor

• Maximum product flow achieved by full port and stem travel design

• All models feature stainless steel stem, spring and valve guide

FEATURES: • Valve body: Ductile Iron/Shutoff poppet

assembly: steel and stainless steel• Available in 1-1/4” NPT, 2” NPT and

3” NPT x 4 Bolt Type A Flange• All models can be used with LP Gas or NH3

• Universal 4 bolt flange inlet type A• Available with permanently bonded on

main valve seals (SBN)

ME873SBN -24(SBN - Bonded Seat)

ME873S-16

ME873S-24

High Flow Back Check Valves - Excela-Flange Series - Socket Weld MARSHALL EXCELSIOR

Item No. Inlet Socket Weld Outlet Socket Weld Propane Flow @ 10 PSIG Pressure Differetial

Weight(lbs.)

ME870SW-16 2” Female 2” Male 189 1.77

ME870SW-16

Liquid Butane Capacity = Flow Rate x .94 | Liquid Anhydrous Ammonia Capacity = Flow Rate x .90

Excela-Flange High Flow Socket Weld Back Check Valves provide flow protection to container openings or liquid lines where flow is intended for one direction. The valve is normally closed until pressure activates the valve when flow is directed into piping or containers causing the back check to open. When flow stops or reverses, the check returns to the closed position. Featuring socket weld connection points, these valves are ideally suited for inline applications where welded piping construction is desired. Only available with metal-to-metal seat.

• Maximum flow achieved by full port and increased stem travel design

• Integral breakaway feature leaves valve as-sembly intact

FEATURES: • All stainless steel internal components• High temperature Inconel spring with-

stands heat from welding

High Flow Single & Double Back Check Fill Valves MARSHALL EXCELSIOR

Item No. Description Differential Flow GPM/LPG @ 10 PSI

ME3194C Single Back Check Fill Valve 3-1/4” M. Acme x 3” MNPT 365ME3197C Double Back Check Fill Valve 3-1/4” M. Acme x 3” MNPT 285

NOTE: For use with LPG only

Marshall Excelsior High Flow Single and Double Back Check Fill Valves provide back flow protection to container openings or liquid lines where flow is intended in one direction. The valve is normally held closed until pressure activates the valve when flow is directed into piping or containers causing the back check to open. When flow stops or reverses, the check returns to the closed position. All MEC high flow back check Valves are supplied with the correct ACME cap and chain assembly.

• Double check primary seat creates metal to metal seating surface

• Double check secondary seat is a soft seat for a leak free seal

• Up to 30% MORE FLOW than nearest competitor

FEATURES: • Maximum product flow achieved by full port

and maximum stem travel design• All models feature a brass stem, stainless

steel spring and bronze valve guide in body check assembly

• For use with LP Gas Only

ME3197C

ME3194C

ME869-10/8


81 82

DD

Inlet

Outlet

Wrench

Propane Liquid Capacity Item No. Material

Connection

Connection

Hex Flats Length at different r Pressure

5 PSIG 10 PSIG 25 PSIG 7100900051 Steel 3/4” F NPT 3/4” M NPT 1-3/8” 1-15/16” (49.2 mm) 10.75 15.7 24.57100900050 Steel 1-1/4” F NPT 1-1/4” M NPT 2” 2-1/2” (63.5 mm) 27.5 39.2 61.757100900049 Steel 2” F NPT 2” M NPT 3” 3 3/8” (83.5 mm) 121.5 171.5 270.5

VENT VALVESBACK CHECK VALVESBack Pressure Valves CAVAGNA GROUP

Cavagna Back Pressure Valves are intended to prevent liquid discharge when the desired flow is directed into the vessel thereby allowing the flow in only one direction. When coupled with the appropriate single check filler valve, the combination forms a double check filler valve suitablefor use in filling of bulk storage tanks.

Back Pressure Valve7100900051



* Rated for LP-Gas and NH3 | **Factory Installed Vent Valve

Marshall Excelsior is the only manufacturer in the industry that offers three types of vent valves –Low Emission, Self-Cleaning Low Emission, and Standard Vent Valves. All of these vent valvesare designed to minimize loss of product while allowing the operator to effectively bleed downconnections and detect liquid levels while filling containers. Vent valves provide an effective means to verify valves have closed in the transfer system when installed into the downstreamauxiliary port on the Marshall Excelsior globe and angle valves. Opening the vent valve until liquid or vapor stops venting indicates it is safe to disconnect.

All brass versions have knurled stems that completely unscrew from the valve making the stems replaceable. The stainless steel version has a t-handle stem that is non-removable.

The Low Emission Vent Valve and the Self-Cleaning Low Emission Vent Valve reduce emissionsby 70% during normal container filling operations. The Self-Cleaning Low Emission Vent Valvecleans out the orifice hole each time it is operated. The hole is cleaned out with a #54 orifice drillthat reams the valve’s orifice hole each time the adjusting screw is loosened or tightened, eliminating nuisance orifice clogging. The reduced venting emissions is achieved by forcing product to pass between the #54 orifice hole and the flutes of the captured self-cleaningapparatus. The self-cleaning replacement screw (MEJ401SC) is compatible with all existing standard vent valve bodies allowing a standard vent valve to be converted into a self-cleaning low emission vent valve without reinstalling the valve body.

The Standard Vent Valve has a #54 orifice with no self-cleaning apparatus.

The Low Emission Vent Valve has a #72 orifice.

• 70% emission reduction with self-cleaning and low emission vent valves• 1/4” MNPT Connection• Available with dip tubes

FEATURES:

Vent Valves MARSHALL EXCELSIOR

MEJ602H

MEJ400SCPatent Pending

Self-Cleaning

MEJ400/72 MEJ400MEJ401SC

Patent Pending

Self-Cleaning

MEJ401

MEJ606 MEJ402S

Item No.Type

Brass Brass Replacement Stems Stainless Steel*MEJ400/72 MEJ401 — Low Emission #72 OrificeMEJ400SC MEJ401SC — Self-Cleaning, Low Emission #54 OrificeMEJ400 MEJ401, MEJ401SC MEJ402S Standard #54 OrificeMEJ400C — — Captured Stem, Standard #54 OrificeMEJ602H*** MEJ400, MEJ401, MEJ401SC — 90° Elbow w/Hydrostatic ReliefMEJ606 MEJ400, MEJ401, MEJ401SC — 90° Elbow, 1/4” MPT x 1/4” M. FlareMES-PVE10ARF — — 1/4” MNPT X, 1/4” M. Flare

MES-PVE10ARF

Item No. Description MaterialME831 Needle Valve 1/4” MNPT x 1/4” FNPT BrassME832 Needle Valve 1/4” MNPT Outlet x #80 Orifi ce 1”- 20 F. Inlet BrassME833 Needle Valve 1/4” MNPT Outlet x 1”- 20 F. Inlet BrassME834 Needle Valve 1/4” MNPT x 9/16” -18 LH Male BrassME831S Needle Valve 1/4” MNPT x 1/4” FNPT Plated SteelME831SS Needle Valve 1/4” MNPT x 1/4” FNPT Stainless Steel

Needle Valves MARSHALL EXCELSIOR

ME832

ME831S

Needle Valves are intended for applications where precise control of gas output is required. These precision machined valves offer a wide range of adjustment without stem galling. Perfectfor isolating pressure gauges from bulk storage containers or upstream shutoff valves for torchesand/or outdoor burner applications.

NEEDLE VALVES

• Available in brass, plated steel and stainless steel construction

• Tapered valve body seat and stem for precision accuracy

FEATURES: • Various inlet/outlet configurations available• ME831 and ME834 series valves approved

for bi-directional flow


MEC Excela-Flange High Flow Socket Weld Tees

Item No. Description Weight(lbs.)

MEP995S-16 Excela-Flange™ 2’’x 2’’x 2” Socket Weld High Flow Tee Body-Steel 6.1MEP995SBW-16 Excela-Flange™ 2’’x 2’’x 2” Butt Weld High Flow Tee Body-Steel 4MEP995S-24/16 Excela-Flange™ 3’’x 2”x 2” Socket Weld High Flow Tee Body-Steel 7.8

MEC Excela-Flange High Flow Socket Weld Elbows


MEP996S-16 Excela-Flange™ 2’’ x 2’’ Socket Weld High Flow Elbow Body-Steel 3.8MEP996SBW-16 Excela-Flange™ 2’’ x 2’’ Butt Weld High Flow Elbow Body-Steel 2.5MEP996S-24 Excela-Flange™ 3’’ x 3’’ Socket Weld High Flow Elbow Body-Steel 6.7

83 84

D D

Item No. Container Connection Outlet Connection DT Length

66.1072 12”66.1116 5.4”66.1117 6.6”66.1118 3.8”66.1119 1/4” MNPT — 4.1”66.1120 5.6”66.1121 6.9”66.1204 Without66.1125 5.2”66.1161 1/4” NPTF 1/4” SAE Flare Without

VENT VALVES

Fixed Liquid Level Gauges CAVAGNA GROUP

• Special DT length can be ordered• Optional instruction plate may be ordered

FEATURES: • Valves incorporate a No. 54 drill size orifice

66.1072

66.1161

Fixed Maximum Liquid Level Gauges MARSHALL EXCELSIOR

TypeItem No.

5.4” Tube LengthBrass




12” Tube LengthBrass

12” Tube LengthStainless Steel*

Low Emission#72 Orifice MEJ410/72-5.4 MEJ410/72-5.7 MEJ410/72-6.6 MEJ410/72-6.9 MEJ410/72-120 —

Self-Cleaning Low Emission#54 Orifice MEJ410SC-5.4 MEJ410SC-5.7 MEJ410SC-6.6 MEJ410SC-6.9 MEJ410SC-120 —

#54 Orifice MEJ410-5.4 MEJ410-5.7 MEJ410-6.6 MEJ410-6.9 MEJ410-120 MEJ402S-120Captured Stem #54 Orifice MEJ410C-5.4 MEJ410C-5.7 MEJ410C-6.6 MEJ410C-6.9 MEJ410C-120 —

* Rated for LP-Gas and NH3

Fixed Maximum Liquid Level Gauges are designed to provide a way to visually determine that a tank has reached maximum allowable fill capacity. The dip tube end of a fixed liquid level gauge should be set equal to 80% of the liquid level tank capacity and installed in the vapor space of the tank. The vent valve should be opened before filling begins during which time vapor will be discharged. Once the tank reaches maximum liquid fill capacity (80% of tank capacity), liquid will begin to discharge from the vent valve telling the operator the tank has reached maximum allowable fill capacity and the filling operation should cease immediately.

NOTE: Available in Stainless Steel i.e. MEP995SS-16

These Tees and Elbows are available in both 2” and 3” socket weld or butt weld pipeconfiguration and maximize flow through system piping where a 90° turn must be made. Flowrates are maximized by an optimized flow path as well as nearly seamless piping joints reducingturbulence and focusing flow through the system. Ideally suited for pump discharge lines, transport loading/unloading tee assemblies, spray fill lines or any other piping application where piping is welded and high flow rates are desired.

• All steel construction for maximum durability and weldability

• Available in 2” and 3” socket weld or butt weld configurations

FEATURES: • Coated for maximum corrosion resistance• Approved for use in LPG or NH3 service• Rated 400 WOG

MEP996S-162” F. Socket Weld X

2” F. Socket Weld Tee

High Flow Socket Weld Bodies Excela-Flange™ Series MARSHALL EXCELSIOR

4 BOLT & SOCKET WELD ADAPTERS

MEP995S-24/163” F. Socket Weld X

(2”) -2” F. Socket Weld Tee

MEP995SBW-163” F. Butt Weld X

(2”) -2” F. Butt Weld Tee

Item No. Description Weight (lbs.)MEP998 Excela-Flange™ 3” - 4 Bolt (Type A) x 2” - 4 Bolt (Type A) Auxiliary Suction Intake 6.25

High Flow 4” Pump Auxiliary Suction Intake Flange Adapters MARSHALL EXCELSIOR

MEC’s Excela-Flanger High Flow 4” Pump Auxiliary Suction Intake Flange Adapters arespecifically designed to bolt directly to 3”- 4 bolt flange auxiliary suction intake openings on standard 4” flange mount mobile transport trailer pumps to eliminate unwanted threaded joints.The MEP998 is equipped with a 4 bolt type A flange inlet for mounting to either ME842 or ME843 series Excela-Flange™ companion flanges where additional piping is desired or direct bolt onto ME819P Series Excela-Flange™ globe valves for a worry-free easy to maintain auxiliaryintake assembly.

• Zinc plated ductile iron body• Approved for use in LPG or NH3 service• Rated 400 WOG

FEATURES: • For use with all Type B (ME842 and ME843

Series) companion flanges

MEP998

MEJ410Series


85 86

D D


MEC Excela-Flange High Flow Cross-over Self Load Intake Adapter


MEP997S-24/16 Excela-Flange™ 3” Socket Weld x (2) 2” Socket Weld x 4 Bolt (Type B) Flange Intake Adapter - Steel 10

NOTE: Available in Stainless Steel construction. To order Stainless Steel add “SS” after the prefix part number - i.e. MEP995SS-16

MEC’s Excela-Flange Series 3”X 2”X 2”X 4-Bolt Flange High Flow Cross-Over Self Loading Intake Adapters are specifically designed to allow for high flow liquid transfer in auxiliary self load cross-over line applications on mobile transport trailers. The MEP997S-24/16 is equipped with a 3” socket weld connection, to allow direct connection to ME994S-3F Series Excela-FlangeInternal Valves and (2) 2” socket weld discharge ports as well as an auxiliary 4 bolt (type B)intake flange. The 4 bolt (type B) intake flange allows for maximum product flow, while providinga convenient flange union for system maintenance.

• Zinc plated steel body• Approved for use in LPG or NH3 service• Rated 400 WOG

FEATURES: • For use with all Type A (ME840 and ME841

Series) companion flanges

High Flow Cross-Over Self Loading Intake Adapter MARSHALL EXCELSIOR

MEP997-24/163” Socket Weld X (2) 2” Socket Weld X 2”- 4 Bolt(Type B) Flange Adapter

MEP997-24/16

MEC Flat Face Flanges

Item No. Description FlangeType

Weight(lbs.)

ME842-10-107 1-1/4” FNPT Tapped 4 Bolt Flat Face Flange Adapter B 2.7ME843-10-107 1-1/4” Socket Weld 4 Bolt Flat Face Flange Adapter B 2.6ME842-12-107 1-1/2” FNPT Tapped 4 Bolt Flat Face Flange Adapter B 2.6ME843-12-107 1-1/2” Socket Weld 4 Bolt Flat Face Flange Adapter B 2.5ME842-16-107 2” FNPT Tapped 4 Bolt Flat Face Flange Adapter B 2.2ME843-16-107 2” Socket Weld 4 Bolt Flat Face Flange Adapter B 2.0

MEC Universal Flange Kit

Item No. Description FlangeType

Weight(lbs.)

ME840-10F 1-1/4” FNPT 4 Bolt Flange Adapter Plate w/Bolts & O-Ring A 3.0ME841-10F 1-1/4” Socket Weld 4 Bolt Flange Adapter Plate w/Bolts & O-Ring A 2.9ME840-12F 1-1/2” FNPT 4 Bolt Flange Adapter Plate w/Bolts & O-Ring A 2.8ME841-12F 1-1/2” Socket Weld 4 Bolt Flange Adapter Plate w/Bolts & O-Ring A 2.7ME840-16F 2” FNPT 4 Bolt Flange Adapter Plate w/ Bolts & O-Ring A 2.5ME841-16F 2” Socket Weld 4 Bolt Flange Adapter Plate w/Bolts & O-Ring A 2.3MEP840-10 1-1/4” FNPT 4 Bolt 90° Flange Adapter Elbow w/Bolts & O-Ring A 4.8MEP841-10 1-1/4” Socket Weld 4 Bolt 90° Flange Adapter Elbow w/Bolts & O-Ring A 4.7MEP840-12 1-1/2” FNPT 4 Bolt 90° Flange Adapter Elbow w/Bolts & O-Ring A 4.6MEP841-12 1-1/2” Socket Weld 4 Bolt 90° Flange Adapter Elbow w/Bolts & O-Ring A 4.6MEP840-16 2” FNPT 4 Bolt 90° Flange Adapter Elbow w/Bolts & O-Ring A 4.3MEP841-16 2” Socket Weld 4 Bolt 90° Flange Adapter Elbow w/Bolts & O-Ring A 4.2

NOTE: Flanges available in Stainless Steel i.e. ME841SS-16F

The 4 Bolt Unions can be used anywhere system piping needs to be joined together between shut off valves. Using piping unions such as these significantly improves the ease by which maintenance can be performed particularly where long runs or multiple directional changes are necessary. Our flange unions feature a captured o-ring design, hardened mounting bolts, and are available in NTP or Socket Weld configurations. Suitable for use in mobile or stationary applications.


• Available in 1-1/4” to 2” FNPT or Socket Weld configurations

• Zinc plated flange faces for maximum corrosion resistance

FEATURES: • No plating on weld surfaces for improved

weld quality with minimum weld prep• Approved for use in LPG or NH3 service• Rated 400 WOG

ME841-16F Type A Flange(Requires purchase of flat face flange)

ME843-16-107 Type B Flange(Requires purchase of mating kit)

MEP840/MEP841

4 Bolt Unions & Companion Flanges MARSHALL EXCELSIOR



MEC Excela-Flange™ High Capacity Pump Discharge ElbowsItem No. Description Fits Pump Model(s)

MEP840H-16 2” FNPT 4 Bolt Type A High Capacity 90° Flange Adapter Elbow with 1/2-13 Bolts and O-RingTLGLF3

MEP841H-16 2” Socket Weld 4 Bolt Type A High Capacity 90° Flange Adapter Elbow with 1/2-13 Bolts and O-RingMEP840HC-16 2” FNPT 4 Bolt Type A High Capacity 90° Flange Adapter Elbow with 3/8-16 Bolts and O-Ring

Z3200MEP840HC-16 2” Socket Weld 4 Bolt Type A High Capacity 90° Flange Adapter Elbow with 3/8-16 Bolts and O-Ring

High Capacity 3” Bobtail Pump Discharge Elbows Excela-Flange™ Series MARSHALL EXCELSIOR High Flow Globe & Angle Valves Overview MARSHALL EXCELSIOR

87 88

D D

GLOBE & ANGLE VALVES

These High Capacity Bobtail Pump Discharge Elbows are designed to maximize the efficiency and flow rate at the outlet of the pump while minimize pressure loss due to the 90 degreedirectional change at the pump outlet needed to direct product to the rear of the vehicle whereit is being dispensed. The MEP840H has carefully modeled radiuses and contours that allow it to flow over 50% more than other standard discharge elbows with 50% less pressure differential, thereby minimizing pump wear and maximizing pumping efficiency. When paired with other Excela-FlangeTM products the bobtail can perform up to its full potential. The MEP840H series is standard with a 1/4” FNPT plugged test port and is available with NPT or socket weld outlet. Suitable for use in mobile or stationary applications.


• Available in 2” FNPT or 2” Socket Weld configurations

• Zinc plated for maximum corrosion resistance

FEATURES: • Approved for use in LPG or NH3 service• Rated 400 WOG• Includes mounting bolts and O-ring• 1/4” FNPT plugged test port

MEP841H-16

NOTE: Flanges available in Stainless Steel i.e. ME841SS-16F

Standard Elbow310 GAL/MIN

MEP841H-16710 GAL/MIN

5 PSI DifferentialLiquid Propane


Marshall Excelsior offers three types of globe and angle valves a (standard, integrated pilot feature (P) or integrated back check feature (IBC)) depending on the intended application. All Marshall Excelsior globe and angle valves are designed to withstand extreme temperatures and can increase flow up to 70 percent over a standard globe valve. The 35 degree seat angleon the 1-1/4” and larger globe valves make them ergonomically designed for bobtail, transportand bulk plant applications. This 35 degree seat angle also allows up to 70 percent more flow. The 1-1/4” and larger globe and angle valves have an optional 360 degree rotating ME829 knob.

To increase the longevity of the seal, all Marshall Excelsior globe and angle valves have a 360 degree rotating seal that stops rotating when it contacts the sealing surface while the valve continues to be tightened. The 1-1/4” and larger models feature ball bearings to facilitate increased seal life.

All 1-1/4” and larger globe and angle valves come with an upstream and downstream pluggedport. The boss of these ports are large enough to drill and tap a 3/4” FNPT hole for a jumper line or standard by-pass valve.

These valves are mainly used in piping systems to control liquid or vapor flow in bulk plants, bobtails, transports, pumps or compressors. Globe valves are designed to be installed in a straight section of piping and angle valves are designed to be installed when a 90 degree directional change is needed in the piping.

Change the sealing compound and Marshall Excelsior’s globe and angle valves can be used in numerous industries including, but not limited to LP-Gas, anhydrous ammonia, petrochemical and chemical applications. The standard seal compound is Nitrile with Teflon® or Viton® alsoavailable. Contact us if you have a need for a different seal compound.

Marshall Excelsior valves are designed to be hand tightened. Using wrenches or excess force to open or close the valve can cause damage to the seal, decreasing the valve’s life.

INSTALLATION NOTE:

Before installing a globe or angle valve, the piping system and container must be free of dirt,debris, foreign matter and other particles, large or small, that could damage the sealing surfaceor seal of the valve. A minimal amount of pipe sealant should be used on the mating part. Excesspipe sealant can also cause damage to the seal surface or seal. Damage to the sealing surfaceor the seal will cause the valve to leak.

To avoid damage to the valve or piping, due to pressure build-up from temperature changes,a hydrostatic relief valve should be installed where liquid can be trapped between twoshutoff valves.

A vent valve should be installed on the downstream side of theglobe or angle valve if the angle valve is used as a shutoff valveat the end of a loading hose. This allows the operator to ventthe rapped liquid before disconnect.

New packingdesign for improved

reliability

Stainless steelinternal components

Rotating seat discincreases life of seal

Black hardcoat for

increaseddurability

ME829E-Z Turn

Knob

35° seat angle increasesflow & improves ergonomics

Up to 70% more flow


89 90

DD

High Flow Globe & Angle Valves MARSHALL EXCELSIOR

ME828-16Patent Pending


ME815-6Vent Valve Not Included

ME815-16

To order Teflon® or Viton® Seal add “T” for Teflon® and “V” for Viton® after the prefix part number, i.e. ME815T-10 or ME815V-10 | Teflon® is a trademarkof DuPont Company and Viton® is a trademark of DuPont Performance Elastomers.

• All stainless steel internal components with rotating seat disc design and V-cup Teflon®

packing stem seals• Double stem seal design ensures leak free

operation• Double lead stem thread ensures quick and

efficient operation• Durable ductile iron valve body with

automotive grade powder coat finish

FEATURES: • 1-1/4” and larger globe valves have 35°

seat angle for maximum product flow• 1-1/4” and larger globe valve designed• 1-3/4”, 2-1/4”, and 3-1/4” Acme threads

available on globe valves• Rated for 400 WOG• Operating temperature –40° to +212° F

Item No.

Inlet(FNPT)

Outlet SidePort T

No. ofSidePorts

FlangeStyle

Bonnet

Accessories

Angle Globe E-Z TurnKnob

Push-To-Turn Locking

Handwheel Kit

HydrostaticRelief Valves

VentValves

ME815-4 ME825-4 1/2” 1/2” FNPT 1/4” 2 No — —

MEH225MEH225SSMEH25/450

MEJ400MEJ400SCMEJ402S

ME815-6 ME825-6 3/4” 3/4” FNPT 1/4” 2 No — —ME815-8 ME825-8 1” 1” FNPT 1/4” 2 No — —ME815-10 ME825-10 1-1/4” 1-1/4” FNPT 1/4” 2 Yes ME829 ME815-16LHK

— ME826-10 1-1/4” 1-3/4” M. Acme 1/4” 2 Yes ME829 ME815-16LHK— ME827-10 1-1/4” 2-1/4” M. Acme 1/4” 2 Yes ME829 ME815-16LHK

ME815-12 ME825-12 1-1/2” 1-1/2” FNPT 1/4” 2 Yes ME829 ME815-16LHKME815-16 ME825-16 2” 2” FNPT 1/4” 2 Yes ME829 ME815-16LHK

— ME824-16 2” 2” FNPT 1/2” 2 Yes ME829 ME815-16LHK MEH50/460 —

ME815-2F ME825-2F 2”-300LBFlanged

2”-300LBFlanged 1/4” 2 Yes ME829 ME815-16LHK

MEH225MEH225SSMEH25/450

MEJ400MEJ400SCMEJ402S

ME815-24 ME825-24 3” 3” FNPT 1/4” 2 Yes Included —

ME815-3F —3”-300LBFlanged

3”-300LBFlanged

1/4” 2 Yes Included —

GLOBE & ANGLE VALVESGLOBE & ANGLE VALVES

Viton® and Teflon® are trademarks of DuPont Performance Elastomers.

The ME813, ME818, ME819 and ME823 Series Valves feature our new modular Excela-Flange 4 Bolt inlet/outlet design that can be easily adapted to both NTP thread or socket weld type A companion flanges (ME840 & ME841 Series) ranging from 1-1/4” to 2” in diameter making it universal to piping sizes within this range. This innovative system allows installers the ability toeliminate unnecessary connections as well as possible leak points by integrating a convenient4 bolt flange union at the valve inlet/outlet connections.

High Flow Globe & Angle Valves Excela-Flange Series MARSHALL EXCELSIOR

Item No. Angle

Item No. Globe Description Side

Ports Inlet OutletMatingFlangeType

Weight (lbs.)

Angle Globe

ME813-10 ME823-10 1-1/4” - 4 Bolt Full Flow Double Flange Valve 1/4” FNPT

4 Bolt Flange Type B


A

14.8 15.3— ME822-16 2” - 4 Bolt Full Flow Double Flange Valve 1/2” FNPT — 19.7

ME813-16 ME823-16 2” - 4 Bolt Full Flow Double Flange Valve 1/4” FNPT 17.6 19.6— ME818-16 2” - 4 Bolt Full Flow Single Flange Valve 1/2” FNPT 2” FNPT — 17.7— ME819-10 1-1/4” - 4 Bolt Full Flow Single Flange Valve 1/4” FNPT 1-1/4” FNPT — 14.0— ME819-16 2” - 4 Bolt Full Flow Single Flange Valve 1/4” FNPT 2” FNPT — 17.7

• All stainless steel internal components with rotating seat disc design and V-cup Teflon®

packing stem seals• Double lead acme stem thread ensures

quick and efficient operation• Durable ductile iron valve body with zinc

plating finish• 1-1/4” and larger globe valves have 35°

seat angle for maximum product flow• 1-1/4” and larger globe valve designed

ergonomically correct for bobtail transport and bulk plant applications

FEATURES: • Rated for 400 WOG• Operating temperature –40° to

+212° Fahrenheit• Up to 70% MORE FLOW than the nearest

competitor• 1/4” FNPT or 1/2” FNPT plugged

accessory ports upstream and downstream of valve seat

• Standard Nitrile seat, optional Teflon® or Viton seatME813-16

2” Double FlangeAngle Valve

ME823-162” Double Flange

Globe Valve

ME819-162” Flange x NPT

Globe Valve

ME829E-Z Turn

Knob

ME825-6Vent Valve

Not Included

ME825-6 withMEP449S-101Replacement

ProtectiveWeather Boot


91 92

DD

GLOBE & ANGLE VALVESGLOBE & ANGLE VALVESHigh Flow Globe & Angle Valves - Next Generation Excela-Flange Series MARSHALL EXCELSIOR

Item No.Angle

Item No.Globe Description Side Ports Inlet Outlet

MatingFlangeType

Weight (lbs.)

Angle Globe

ME813IBC-16 ME823IBC-16 2” Full Flow 4 Bolt Double Flange (IBC) Valve 1/4” FNPT


4 BoltFlangeType B

A 17.6 20.1— ME822IBC-16 2” Full Flow 4 Bolt Double Flange (IBC) Valve 1/2” FNPT A — 19.7

ME813P-16 ME823P-16 2” Full Flow 4 Bolt Double Flange (P) Valve 1/4” FNPT A 18.1 20.1— ME822P-16 2” Full Flow 4 Bolt Double Flange (P) Valve 1/2” FNPT A — 20.1— ME818IBC-16 2” Full Flow 4 Bolt Single Flange (IBC) Valve 1/2” FNPT

2” FNPT

A — 18.2— ME818P-16 2” Full Flow 4 Bolt Single Flange (P) Valve 1/2” FNPT A — 18.2— ME819IBC-16 2” Full Flow 4 Bolt Single Flange (IBC) Valve 1/4” FNPT A — 18.1— ME819P-16 2” Full Flow 4 Bolt Single Flange (P) Valve 1/4” FNPT A — 18.1

The Next Generation Flanged 2” Globe and Angle Valves feature our new modular Excela-Flange 4 Bolt inlet/outlet design that can be easily adapted to both NTP thread or socket weld type Acompanion flanges (ME840 and ME841 Series) ranging from 1-1/4” to 2” in diameter making ituniversal to piping sizes within this range. This innovative system allows installers the ability to eliminate unnecessary connections as well as possible leak points by integrating a convenient4 bolt flange union at the valve inlet/outlet connections.

All of the same great features of the original Full Flow MEC Globe Valves with additional product performance enhancements.

Pilot Feature (P): This globe valve model incorporates a pilot orifi ce feature to facilitate pressure equalization in sections of system piping that have bidirectional flow or high differential pressures. This greatly reduces the opening torque required and prevents premature wear of the valve seat.

Integrated Back Check Feature (IBC): These globe and angle valve models incorporate an integrated back check feature to allow trapped downstream pressure to automatically bypass to the upstream side of the valve. These valves are designed for systems with flow in one direction, creating a closed loop system that prevents the product from relieving to the atmosphere making for a low emission, more environmentally friendly option.

ME819P-162” - Flange x NPT

Globe Valve

Integrated Back Check Feature

ME823IBC-16

Pilot Feature

ME823P-16

High Flow Globe & Angle Valves - Excela-Flange 2” Bottom Port / Integrated Pilot Valves MARSHALL EXCELSIOR

Item No. Description 1/4” FNPTSide Port A

1/4” FNPTSide Port B Side Ports Inlet Outlet

MatingFlangeType

Weight (lbs.)

ME822P-16-4*

2” Full Flow4 Bolt Flange

(P) Valve

Plugged Plugged Plugged

4 BoltFlangeType B

4 Bolt Flange Type B A 20.2ME823P-16-4 Plugged Plugged Plugged 4 Bolt Flange Type B A 20.2ME823P-16H-4 Plugged MEH225 Plugged 4 Bolt Flange Type B A 20.2ME823P-16HSS-4 Plugged MEH225SS Plugged 4 Bolt Flange Type B A 20.2ME818P-16-4* Plugged Plugged Plugged 2” FNPT A 18.2ME819P-16-4 Plugged Plugged Plugged 2” FNPT A 18.2ME819P-16H-4 Plugged MEH225 Plugged 2” FNPT A 18.2ME819P-16HSS-4 Plugged MEH225SS Plugged 2” FNPT A 18.2

Excela-Flange 2” Bottom Port / Integrated Pilot Valves provide a positive shut-off valve that is highly reliable with full flow performance while providing bi-directional flow. Ideally suited for use on transport trailers with 1/2” blow down lines to provide rapid and complete product evacuation prior to disconnecting transfer hose. Valves can be purchased with hydrostatic relief valves pre-installed on the out board side port of the globe valve main seal.

All of the same great features of the original full flow MEC globe valves with additional product performance enhancements.

Pilot Feature (P): This globe valve model incorporates a pilot orifice feature to facilitate pressure equalization in sections of system piping that have bidirectional flow or high differential pressures. This greatly reduces the opening torque required and prevents premature wear of the valve seat.

The Excela-Flange 2” Bottom Port Operated Flanged Globe Valves feature our new modular Excela-Flange 4 bolt inlet/outlet flange design that can be easily adapted to both NPT thread or socket weld Type A companion flanges (ME840 and ME841 Series) ranging from 1-1/4” to 2” in diameter making it universal to piping sizes within this range. This innovative system allows installers the ability to eliminate unnecessary connections as well as possible leak points by integrating a convenient 4 bolt flange union at the valve inlet/outlet connections.

ME819P-16-42” - Flange x NPT Pilot Globe Valve

Port A1/4” FNPT

Pilot Feature

Pilot Feature

ME823P-16-42” - Double FlangePilot Globe Valve

Port C1/2” FNPT

Port B1/4” FNPT


93 94

D D

Item No. Descriptions

ME815-16LHK Push-To-Turn Locking Handwheel Kit for all 1-1/4”,

1-1/2” and 2” MEC Angle / Globe Valves

Marshall Excelsior’s Next Generation High Flow Globe and Angle Valves have the same great features of the original High Flow Marshall Excelsior globe and angle valves with additional product performance enhancements. These globe and angle valves provide a positive shutoff thatis highly reliable with High Flow performance, bidirectional flow, or reduced product emissions.

The Integrated Back Check Feature (IBC) is designed for use in sections of piping where the trapped liquid pressure may exceed 100 PSIG between two valves. When trapped liquid pressureexceeds 100 PSIG, the integrated back check feature automatically bypasses trappeddownstream system pressure through the valve seat to the upstream side of the valve into theproduct container or piping. A closed looped system is created because the 100 PSIG is far below the 400 - 500 PSIG set pressure of a hydrostatic relief valve keeping the product in the system and reducing product emissions.

WARNING: NFPA 58 requires that a hydrostatic relief valve be installed into any section of pipingthat could allow liquid to become trapped between two shutoff valves.

The Integrated Pilot Feature (P) is designed for sections of piping that have bidirectional flow. Standard globe and angle valves installed in bidirectional systems can have a potential for backpressure to build-up on the upstream side of a closed valve. This pressure adds to the force required to open the valve causing additional wear to the valve stem and seat material. The integrated pilot feature allows the first portion of stem travel to unseat the pilot orifice,automatically equalizing the system pressure prior to unseating the valve holder seal. This greatlyreduces the opening torque required in bidirectional systems and prevents premature wear of the primary valve seat material and valve components.

Next Generation High Flow Globe and Angle Valves MARSHALL EXCELSIOR

GLOBE & ANGLE VALVES

Item No.

Inlet(FNPT)

Outlet SidePort T

No. ofSidePorts

FlangeStyle

Bonnet

AccessoriesAngle Globe

E-Z TurnKnob

HydrostaticReliefValves

VentValvesIntegrated

Back CheckPilot

FeatureIntegratedBack Check

PilotFeature

ME815IBC-16 ME815P-16 ME825IBC-16 — 2” 2” FNPT 1/4” 2 Yes ME829 MEH225MEH225SMEH25/450

MEJ400MEJ400SCMEJ402S— — ME828IBC-16 — 2”

3-1/4” Male Acme

1/4” 2 Yes ME829

— — ME824IBC-16 — 2” 2” FNPT 1/2” 2 Yes ME829 MEH50/460 —

Integrated Back CheckFeature (IBC)

ME825IBC-16U.S. and Canada

Patented

Up to70%More Flow

Integrated PilotFeature (P)

ME825P-16U.S. and Canada

Patented

Up to70%More Flow

Next Generation 2” Bottom Port Globe Valves provide a positive shut-off valve that is highly reliable with full flow performance while providing bidirectional flow. Ideally suited for use on transport trailers with 1/2” blow down lines to provide rapid and complete product evacuationprior to disconnecting the transfer hose. Valves can be purchased with hydrostatic relief valvespre-installed in the side port of the globe valve downstream of the main seal. The valves includea pilot orifice feature to facilitate pressure equalization in sections of system piping that have bidirectional flow or high differential pressures, greatly reducing the opening torque required and preventing premature wear of the valve seat. These valves have all of the great features of the original full flow MEC Globe Valves with additional product performance enhancements.

Pilot Feature (P): These globe valve models incorporate a pilot orifice feature to facilitate pressure equalization in sections of system piping that have bidirectional flow or high differentialpressures. This greatly reduces the opening torque required and prevents premature wear of the valve seat.

ME825P-16HSS-4

GLOBE & ANGLE VALVESHigh Flow Globe & Angle Valves - 2” Next Generation - 1/2” Bottom Port MARSHALL EXCELSIOR

Item No. Description 1/4” FNPTSide Port A

1/4” FNPTSide Port B

1/2” FNPTBottom Port

Inlet/Outlet

Accessories

E-Z Turn Knob

ME825P-16-4 Full Flow Valve with Integrated Pilot Feature Plugged PluggedPlugged 2” FNPT ME829ME825P-16H-4 Full Flow Valve with Integrated Pilot Feature Plugged MEH225

ME825P-16HSS-4 Full Flow Valve with Integrated Pilot Feature Plugged MEH225SS

Port B1/4” FNPT

Port C1/2” FNPT

Port C1/4” FNPT

Pilot Feature

Marshall Excelsior’s Push-to-Turn Locking Handwheel Kit helps prevent accidental opening of any 1-1/4”, 1-1/2”, or 2” MEC angle or globe valve configuration. Once installed the kit requires the operator to push down on the hand wheel to engage the valve stem in order to open or fully close the valve making it a deliberate action to actuate. The ejection spring disengages the handwheel from the stem when released, preventing unintentional opening of the valve.

Globe and Angle Valves Push-to-Turn Locking Handwheel Kit MARSHALL EXCELSIOR


Item No. Description Side PortsNo. of

Side PortsInlet Outlet

ME825-3F Full Port Globe Valve with Integrated Pilot Feature 1/4” FNPT 2 3”-300 LB 3”-300 LBME825-4F Full Port Globe Valve with Integrated Pilot Feature 1/4” FNPT 2 4”-300 LB 4”-300 LB

95 96

DD

Item No. Accessory Descriptions

ME829 Black Handwheel E-Z Turn Knob KitME980SK-24 3” & 4”- 300 lb. ESV & Globe Valve Flange Stud KitME904S-3F-027 3”- 300 lb. Spiral Ring Flange Gasket-Carbon SteelME904S-4F-027 4”- 300 lb. Spiral Ring Flange Gasket-Carbon Steel

Y-STRAINERSGLOBE & ANGLE VALVESFlanged Full Port Globe Valves MARSHALL EXCELSIOR

Full Port Flanged Globe Valves provide all the servicability features of a traditional globe valve with the full port flow capacity of a ball valve. Flanged end connections facilitate easy servicing along with a replaceable valve seat providing long service life for your investment. The valve also features an integrated pilot feature allowing pressure equalizing across the valve seat forbi-directional system flow.

Pilot Feature (P): These globe valve models incorporate a pilot orifice feature to facilitate pressure equalization in sections of system piping that have bidirectional flow or high differentialpressures. This greatly reduces the opening torque required and prevents premature wear of the valve seat.

• Has same great reliable and durable teflon stem packing glands as our other globe valves

• Features exclusive slip cam construction for full port flow rates

• Removable bonded main seat disc assembly

FEATURES: • All stainless steel internal component

construction for maximum corrosion resistance

• Same overall length as ANSI ball valve

ME825-3F

Y-Strainers MARSHALL EXCELSIOR

Y-Strainers are designed for flow in one direction to guard against debris in pipelines that couldcause damage to pumps, valves or other equipment. They can be installed horizontally orvertically and are available in three stainless steel mesh sizes. The mesh size equals the numberof holes per square inch (i.e. the smaller the number the larger the holes). A shutoff valve installed on the filter basket outlet allows for convenient blow-off cleaning of Y-Strainer while under pressure. The ME656S Series Ductile Iron Strainers are available in 3” or 4” -300 lb ANSI flange sizes with threaded blow-off ports. All strainers come standard with 40 mesh stainless steel reinforced screens for maximum durability and protection of downstream equipment. Plugs for the threaded blow-offs are available at additional cost.*

ME656S-3F

ME653S

* To add a factory installed plug use a “P” after the prefix number i.e. ME650SP/20

• Durable ductile iron body with automotive grade powder coat finish• Rated 600 PSI / WOG

FEATURES: • Optional factory installed plug*• Designed for LP-Gas or NH3

Item No. Blow-Off Plug Size

Inlet & OutletFNPT20 Mesh Screen 40 Mesh Screen 80 Mesh Screen

ME650S/20 ME650S ME650S/80 1/2” 1/2” ME651S/20 ME651S ME651S/80 1/2” 3/4” ME652S/20 ME652S ME652S/80 3/4” 1” ME653S/20 ME653S ME653S/80 3/4” 1-1/4”

— ME654S — 1” 1-1/2”ME655S/20 ME655S ME655S/80 1” 2”

— ME655S-2F — 1” 2”-300 LB Flange

— ME656S ME656S/80 1-1/4” 3” — ME656S-3F — 1-1/4” 3”-300 LB Flange — ME656S-4F — 1-1/4” 4”-300 LB Flange

ME655S

ME656S

ME656S-3F-901ME656S-3F Replacement Screen

ME653SP


97 98

E E

Ball Valves JOMAR

Item No. Input Output Type Side Tap

T-204DU FIP X FIP 1/2” FNPT* 1/2” FNPT T-204DU FIP X FL 1/2” FNPT 1/2” Flare

Dielectric

—

T-203DU FIP X FIP 1/2” FNPT* 1/2” FNPT 1/8”

T-203DU FIP X FL 1/2” FNPT 1/2” Flare T-204 FIP X FIP 1/4” FNPT* 1/4” FNPT

Threaded —

T-203 FIP X FIP 3/8” FNPT* 3/8” FNPT* 1/8”T-204 FL X FL 3/8” Flare* 3/8” Flare

—T-204 FL X FIP 3/8” Flare* 1/2” FNPT

Flare

T-203 FL X FL 3/8” Flare* 3/8” Flare 1/8”

T-203 FL X FIP 1/2” Flare 1/2” FNPT

Carbon Steel Gas Ball Valve FL-CS-100-300 JOMAR

Item No. Size

600-228 2” 600-230 3” 600-231 4”

Item No. Size

600-232 6” 600-233 8”

Carbon Steel Gas Ball Valve T-CS-2002N-SS-DUE JOMAR

Item No. Size

100-991 1/4” 100-992 3/8” 100-993 1/2” 100-994 3/4”

Item No. Size

100-995 1” 100-996 1-1/4” 100-997 1-1/2” 100-998 2”

Carbon Steel Gas Ball Valve T-CS-1001N-SS JOMAR

Item No. Size

100-971 1/4” 100-972 3/8” 100-973 1/2” 100-974 3/4”

Item No. Size

100-975 1” 100-976 1-1/4” 100-977 1-1/2” 100-978 2”

Carbon Steel Gas Ball Valve S-CS-1000N-SS-4B JOMAR

Item No. Size

100-503 1/2” 100-504 3/4” 100-505 1”

Item No. Size

100-506 1-1/4” 100-507 1-1/2” 100-508 2”

Stainless Steel Flanged Gas Ball Valve FL-SS-100-300 JOMAR

Item No. Size

600-128 2” 600-130 3” 600-131 4”

Item No. Size

600-132 6” 600-133 8”

Stainless Steel Gas Ball Valve T-SS-2002N-DUE JOMAR

Item No. Size

100-981 1/4” 100-982 3/8” 100-983 1/2” 100-984 3/4”

Item No. Size

100-985 1” 100-986 1-1/4” 100-987 1-1/2” 100-988 2”

BALL VALVESBALL VALVES

*Size listed is the smallest size in the series. Larger sizes are available. | More gas valves are available upon request. Speak to your MTankCo representative for more information.

• Ideal for use outside in extremely cold climates

• 2 Viton® O-rings

FEATURES: • 100% leak tested• Made in Italy• Leakproof stem - LIFETIME WARRANTY

FL-CS-100-300The FL-CS-100-300 is a full port, API 607 fire safe certified, NACE MR0175 approved 1/4 turn flanged ball valve. It has a WCB carbon steel body, stainless steel ball and stem, RPTFE seats, blow-out proof stem, and actuator mounting pads.

T-CS-2002N-SS-DUE

The T-CS-2002N-SS-DUE is a 1/4 turn, lever handle operated, WCB carbon steel body with stainless steel ball and stem. It has a five-piece, double-union end body design, is 100% full port, with a blow-out proof stem.

T-CS-1001N-SS

The T-CS-1001N-SS is a 1/4 turn, latch-lock, lever handle operated, two-piece body designed, gas ball valve. This valve has a WCB carbon steel body with stainless steel ball and stem. It is 100% full port with a blow-out proof stem.

S-CS-1000N-SS-4B

S-CS-1000N-SS-4B is a 1/4 turn, latch lock, lever handle operated gas ball valve. This valve has athree-piece WCB carbon steel body with four-bolt (swing-out pattern). It is 100% full port, with a stainless steel solid ball and blow-out proof 316 stainless steel stem.

The FL-SS-100-300 is a 100% full port, API 607 fire safe certified, NACE MR0175 approved, 1/4 turn flanged ball valve. It has a stainless steel body, ball and stem, RPTFE seats, blow-out proof stem, and actuator mounting pads.

FL-SS-100-300

The T-SS-2002N-DUE is a double union ball valve that is UL approved for flammable liquids including liquid propane, LP gas, anhydrous ammonia, natural and manufactured gas. These valves are designed for industrial applications of steam, water, oil, gas, and corrosive materials.

T-SS-2002N-DUE

T-204DU FIP X FIP

T-203 FL X FL


99 100

E E

Item No. Size

500-301 1/4” 500-302 3/8” 500-303 1/2” 500-304 3/4” 500-305 1”

Item No. Size

500-306 1-1/4” 500-307 1-1/2” 500-308 2” 500-310 3” 500-311 4”

Item No. Size

500-301 VB 1/4” 500-302 VB 3/8” 500-303 VB 1/2” 500-304 VB 3/4” 500-305 VB 1”

Item No. Size

500-306 VB 1-1/4” 500-307 VB 1-1/2” 500-308 VB 2” 500-310 VB 3” 500-311 VB 4”

Item No. Size

100-961 1/4” 100-962 3/8” 100-963 1/2” 100-964 3/4”

Item No. Size

100-965 1” 100-966 1-1/4” 100-967 1-1/2” 100-968 2”

Item No. Size

100-961VB 1/4” 100-962VB 3/8” 100-963VB 1/2” 100-964VB 3/4”

Item No. Size

100-965VB 1” 100-966VB 1-1/4” 100-967VB 1-1/2” 100-968VB 2”

Item No. Size

100-701 1/4” 100-702 3/8” 100-703 1/2” 100-704 3/4” 100-705 1” 100-706 1-1/4”

Item No. Size

100-707 1-1/2” 100-708 2” 100-709 2-1/2” 100-710 3” 100-711 4”

Item No. Size

170-103 1/2” 170-104 3/4” 170-105 1”

Item No. Size

170-106 1-1/4” 170-107 1-1/2” 170-108 2”

Item No. Input

100-295 1/4” FIP x 1/4” MIP (Screwdriver Slot Handle) 100-296 1/4” FIP x 1/8” MIP (Screwdriver Slot Handle) 100-297 1/8” FIP x 1/8” MIP 100-298 1/4” FIP x 1/8”MIP 100-299 1/4” FIP x 1/4” MIP 100-300 1/4” FIP x 1/4” FIP

Item No. Size

100-703NGDZ 1/2” 100-704NGDZ 3/4” 100-705NGDZ 1”

Item No. Size

100-706NGDZ 1-1/4” 100-707NGDZ 1-1/2” 100-708NGDZ 2”

Item No. Size

100-601 1/4” 100-602 3/8” 100-603 1/2”

Item No. Size

100-707 3/4” 100-708 1”

Brass Gas Ball Valve T-82 Mini JOMAR

Stainless Steel Gas Ball Valve T-SS-1000N-4B JOMAR

T-SS-1000N-4B

The T-SS-1000N-4B is a quarter turn, lever handle operated, stainless steel gas ball valve. Its latchlock handle can be locked in open or closed positions. It has a three-piece body design, four-bolt(swing-out pattern), full port, stainless steel solid ball, and blow-out proof stainless steel stem.

BALL VALVESBALL VALVES

Stainless Steel Gas Vented Ball Valve T-SS-1000N-4B-VB JOMAR

T-SS-1000N-4B-VB

The T-SS-1000N-4B-VB is a quarter turn, lever handle operated, stainless steel body, three-piece,four-bolt (swing-out pattern), full port, with threaded connection. This valve has a stainless steelvented solid ball, with blow-out proof stainless steel stem. The latch lock handle can be lockedin open or closed positions.

Stainless Steel Gas Ball Valve T-SS-1001N JOMAR

T-SS-1001N

The T-SS-1001N is a two-piece, stainless steel body design with threaded connection. It has a quarter turn, latch-lock, and is lever handle operated. Its ball and stem are stainless steel, has a 100% full port, and blow-out proof stem.

Stainless Steel Gas Ball Valve T-SS-1001N-VB JOMAR

The T-SS-1001N-VB is a quarter turn, latch-lock, lever handle operated, two-piece stainless steel gas ball valve with a stainless steel vented ball. It has a 100% full port with a stainless steel blow-out proof stem.

T-SS-1001N-VB

Brass Threaded Gas Ball Valve T-100NE JOMAR

Brass Threaded Gas Ball Valve T-100S TN with Side Tap JOMAR

T-100NE

S-100FMN

T-82 Mini

Bronze Substitute Gas Ball Valve T-100NEG JOMARBronze Substitute Gas Ball Valve T-100NEG JOMAR

T-100NEG

Brass Gas Ball Valve T-100FMN JOMAR

T-100NE


101 102

E E

Item No. Size

100-102 3/8” 100-103 1/2”

Item No. Size

100-304 1/4”

Item No. Input Output Type Side Tap

T-3 1/2 FP X FP 1/2” FNPT 1/2” FNPT T-3 3/4 FP 3/4” FNPT 3/4” FNPT FNPT X FNPT 1/8”T-3 1 FP X FP 1” FNPT 1” FNPT T-3 3/8 FL X 1/2 FIP 3/8” FL 1/2” FIP T-3 1/2 FL X 1/2 FIP 1/2” FL 1/2” FIP T-3 1/2 FL X 3/4 FIP 1/2” FL 3/4” FIP T-3 5/8 (16) FL X 1/2 FIP 5/8” (15/16-16) FL 1/2” FIP Flare X FIP —T-3 5/8 (14) FL X 3/4 FIP 5/8” (7/8-14) FL 3/4” FIP T-3 5/8 (16) FL X 3/4 FIP 5/8” (15/16-16) FL 3/4” FIP T-3 3/8 (24) FL X 1/2 FIP 3/8” (9/16-24) FL 1/2” FIP T-3 3/8 FL X 1/2 MP 3/8” FL 1/2” MP

Flare X MIP

—T-3 1/2 FL X 1/2 MP 1/2” FL 1/2” MP T-3 3/8 FL X 3/8 FL 3/8” FL 3/8” FL T-3 1/2 FL X 1/2 FL 1/2” FL 1/2” FL Flare X Flare —T-3 5/8 FL X 5/8 FL 5/8” FL 5/8” FL

Item No. Size Description

SLP 1/4 2 2 ft. SLP 1/4 3 3 ft.SLP 1/4 4 4 ft.SLP 1/4 5 5 ft.SLP 1/4 6 6 ft. 1/4” Hose Assembly, 3/8” FL ELSLP 1/4 8 8 ft.SLP 1/4 10 10 ft.SLP 1/4 20 20 ft.SLP 1/4 25 25 ft.SLP 3/8 6 6 ft.SLP 3/8 10 10 ft.SLP 3/8 15 15 ft. 3/8” Hose Assembly, 3/8” FL EESLP 3/8 20 20 ft.SLP 3/8 25 25 ft.

BALL VALVESBlue Top Gas Ball Valves T-3000 LEGEND

Blue Top Gas Ball Valves T-3100 LEGEND

The T-3000 is one-piece, heavy duty forged brass valve designed as a gas appliance connector for use with natural, manufactured, mixed, liquefied petroleum and LP gas/air mixtures.

The T-3100 Series is one-piece, heavy duty forged brass valve designed as a gas applianceconnector. This valve is for use with natural, manufactured, mixed, liquefied petroleum and LP gas/air mixtures.

T-3000

T-3 1/2 FL X FL

T-3 1/2 FL X FIP

T-3100 FL X FL

HOSE ASSEMBLIESHose Assemblies

1/4” Hose Assembly

3/8” Hose Assembly


103 104

FF

Description

Item No. 1/8” 1/4” 3/8” 1/2”90° Elbow, FIP X FIP 1/8 90 EL 1/4 90 EL 3/8 90 EL 1/2 90 EL90º Street Elbow , FIP X MIP 1/8 ST EL 1/4 ST EL 3/8 ST EL 1/2 ST EL45º Elbow, FIP X FIP 1/8 45 EL 1/4 45 EL 3/8 45 EL 1/2 45 EL45º Street Elbow , FIP X MIP 1/8 45 ST EL 1/4 45 ST EL 3/8 45 ST EL 1/2 45 ST EL90º Elbow, Side Outlet, FIP X FIP X FIP 1/8 90 EL SO 1/4 90 EL SO 3/8 90 EL SO 1/2 90 EL SOTee - Straight, FIP X FIP X FIP 1/8 TEE 1/4 TEE 3/8 TEE 1/2 TEEService Tee, MIP X FIP X FIP 1/8 SRV TEE 1/4 SRV TEE 3/8 SRV TEE 1/2 SRV TEETee, Side Outlet FIP X FIP X FIP X FIP 1/8 SO TEE 1/4 SO TEE 3/8 SO TEE 1/2 SO TEECross, FIP X FIP X FIP X FIP 1/8 CRS 1/4 CRS 3/8 CRS 1/2 CRS

Description

Item No. 3/4” 1” 1-1/4” 1-1/2”90° Elbow, FIP X FIP 3/4 90 EL 1 90 EL 1-1/4 90 EL 1-1/2 90 EL90º Street Elbow , FIP X MIP 3/4 ST EL 1 ST EL 1-1/4 ST EL 1-1/2 ST EL45º Elbow, FIP X FIP 3/4 45 EL 1 45 EL 1-1/4 45 EL 1-1/2 45 EL45º Street Elbow , FIP X MIP 3/4 45 ST EL 1 45 ST EL 1-1/4 45 ST EL 1-1/2 45 ST EL90º Elbow, Side Outlet, FIP X FIP X FIP 3/4 90 EL SO 1 90 EL SO 1-1/4 90 EL SO 1-1/2 90 EL SOTee - Straight, FIP X FIP X FIP 3/4 TEE 1 TEE 1-1/4 TEE 1-1/2 TEEService Tee, MIP X FIP X FIP 3/4 SRV TEE 1 SRV TEE 1-1/4 SRV TEE 1-1/2 SRV TEETee, Side Outlet FIP X FIP X FIP X FIP 3/4 SO TEE 1 SO TEE 1-1/4 SO TEE 1-1/2 SO TEECross, FIP X FIP X FIP X FIP 3/4 CRS 1 CRS 1-1/4 CRS 1-1/2 CRS

Description

Item No. 2” 2-1/2” 3” 4”90° Elbow, FIP X FIP 2 90 EL 2-1/2 90 EL 3 90 EL 4 90 EL90º Street Elbow , FIP X MIP 2 ST EL 2-1/2 ST EL 3 ST EL 4 ST EL45º Elbow, FIP X FIP 2 45 EL 2-1/2 45 EL 3 45 EL 4 45 EL45º Street Elbow , FIP X MIP 2 45 ST EL 2-1/2 45 ST EL 3 45 ST EL 4 45 ST EL90º Elbow, Side Outlet, FIP X FIP X FIP 2 90 EL SO 2-1/2 90 EL SO 3 90 EL SO 4 90 EL SOTee - Straight, FIP X FIP X FIP 2 TEE 2-1/2 TEE 3 TEE 4 TEEService Tee, MIP X FIP X FIP 2 SRV TEE 2-1/2 SRV TEE 3 SRV TEE 4 SRV TEETee, Side Outlet FIP X FIP X FIP X FIP 2 SO TEE 2-1/2 SO TEE 3 SO TEE 4 SO TEECross, FIP X FIP X FIP X FIP 2 CRS 2-1/2 CRS 3 CRS 4 CRS

Description

Item No. 1/4” 3/8” 1/2” 3/4” 1” 1-1/2”Couplings 1/4 CO 3/8 CO 1/2 CO 3/4 CO 1 CO 1-1/2 COHex Plugs 1/4 PLUG 3/8 PLUG 1/2 PLUG 3/4 PLUG 1 PLUG 1-1/2 PLUGCaps 1/4 CAP 3/8 CAP 1/2 CAP 3/4 CAP 1 CAP 1-1/2 CAPUnions 1/4 UNION 3/8 UNION 1/2 UNION 3/4 UNION 1 UNION 1-1/2 UNION

Nipple Item No. Description 1/4” 3/8” 1/2” 3/4” 1”Close 1/4 CL 3/8 CL 1/2 CL 3/4 x CL 1 x CL1-1/2” Long 1/4 x 1-1/2 3/8 x 1-1/2 1/2 x 1-1/2 3/4 x 1-1/2 1 x 1-1/22” Long 1/4 x 2 3/8 x 2 1/2 x 2 3/4 x 2 1 x 22-1/2” Long 1/4 x 2-1/2 3/8 x 2-1/2 1/2 x 2-1/2 3/4 x 2-1/2 1 x 2-1/2 3” Long 1/4 x 3 3/8 x 3 1/2 x 3 3/4 x 3 1 x 33-1/2” Long 1/4 x 3-1/2 3/8 x 3-1/2 1/2 x 3-1/2 3/4 x 3-1/2 1 x 3-1/24” Long 1/4 x 4 3/8 x 4 1/2 x 4 3/4 x 4 1 x 44-1/2” Long 1/4 x 4-1/2 3/8 x 4-1/2 1/2 x 4-1/2 3/4 x 4-1/2 1 x 4-1/25” Long 1/4 x 5 3/8 x 5 1/2 x 5 3/4 x 5 1 x 56” Long 1/4 x 6 3/8 x 6 1/2 x 6 3/4 x 6 1 x 67” Long 1/4 x 7 3/8 x 7 1/2 x 7 3/4 x 7 1 x 78” Long 1/4 x 8 3/8 x 8 1/2 x 8 3/4 x 8 1 x 89” Long 1/4 x 9 3/8 x 9 1/2 x 9 3/4 x 9 1 x 9 10” Long 1/4 x 10 3/8 x 10 1/2 x 10 3/4 x 10 1 x 1011” Long 1/4 x 11 3/8 x 11 1/2 x 11 3/4 x 11 1 x 1112” Long 1/4 x 12 3/8 x 12 1/2 x 12 3/4 x 12 1 x 12 18” Long 1/4 x 18 3/8 x 18 1/2 x 18 3/4 x 18 1 x 1824” Long 1/4 x 24 3/8 x 24 1/2 x 24 3/4 x 24 1 x 2430” Long 1/4 x 30 3/8 x 30 1/2 x 30 3/4 x 30 1 x 30

Galvanized Nipple Item No. Description 1/4” 3/8” 1/2” 1”

Bushing - 3/8” 3/8 x 1/4 BU 3/8 x 3/8 BU 3/8 x 1/2 BU 3/8 x 1 BUBushing - 1/2” 1/2 x 1/4 BU 1/2 x 3/8 BU 1/2 x 1/2 BU 1/2 x 1 BUBushing - 3/4” 3/4 x 1/4 BU 3/4 x 3/8 BU 3/4 x 1/2 BU 3/4 x 1 BUThreaded Pipe 18” Long 18 x 1/4 THRD Pipe 18 x 3/8 THRD Pipe 18 x 1/2 THRD Pipe 18 x 1 THRD PipeThreaded Pipe 24” Long 24 x 1/4 THRD Pipe 24 x 3/8 THRD Pipe 24 x 1/2 THRD Pipe 24 x 1 THRD PipeThreaded Pipe St. Elbow 1/4 ST EL 3/8 ST EL 1/2 ST EL 1 ST ELTee 1/4 TEE 3/8 TEE 1/2 TEE 1TEE

Product Material Ordering Abbreviation

Galvanized GAL Black Iron BLK Forged Steel (Extra Heavy) FS

FITTINGSFITTINGSPipe Fittings Couplings, Hex Head Plugs, Caps, and Unions

Nipples

Bushings, Threaded Pipe, Street Elbow, and Tee Fittings

ORDERING NOTE: Symbols on the Product Chart to the left denote the materials in which fittings are available. When ordering, add the corresponding prefix to the Item Number to indicate the product material. For example, when orderinga Black Iron, 1/4”, 45º Elbow, FIP X FIP order number will be BLK 1/4 45 EL.

Contact your MTankCo representative if you are unable to find the part or parts you are looking for.

90ºElbow

Street Elbow

Coupling Union

Tee Cross

Plug Cap


105 106

FF

SIGHT FLOW SWING CHECK VALVES SIGHT FLOW SWING CHECK VALVESSight Flow Swing Check Valves MARSHALL EXCELSIOR

1-1/4” - 4” Flow Indicating Swing Check Valves MARSHALL EXCELSIOR

Flow Indicating Swing Check Valves promotes maximum pump efficiency by providing systemoperators with a visual inspection point for monitoring liquid flow conditions as well as providinga soft seat back check valve to prevent reverse product flow. Installation of a flow indicating swingcheck valve upstream of the pump allows the operator to observe product flow and make pumpadjustments for maximum flow without cavitation. Suitable for stationary and mobile applications.

• Powder coated ductile iron body for maximum durability• Removable flanged ends for easy field

service• Integral swing away check valve with soft

seat to promote maximum product flow and prevent reverse product flow

• All stainless steel, corrosion resistant internal component construction

FEATURES: • Magnetically coupled flow indicator for

maximum protection against leaks and minimal resistance to product flow

• Easy to read flow indicator with “Glow” arrow shows if valve is open/closed• UL Listed for use with LP Gas and Anhydrous Ammonia - 400 PSI WOG

ME875S-16

ME981-10Indicating Check Valve

ME982-10

Item No. Inlet and Outlet FNPT Seal Material OAL

ME875S-16 2” Nitrile 5-3/4”ME875SN-16 2” Neoprene 5-3/4”ME875SV-16 2” Viton® 5-3/4”ME875S-24 3” Nitrile 7-3/8”ME875SN-24 3” Neoprene 7-3/8”ME875SV-24 3” Viton® 7-3/8”ME875S-3F* 3”-300LB Flange Nitrile 10-1/2”

* “NC” indicates no check e.i. ME875SNC-16 | Viton® is a trademark of DuPont Performance Elastomers | * Not a UL Listed Configuration

• Specially formulated, large diameter impact resistant sight glass with O-ring packing seals for maximum safety and visibility

• Durable ductile iron body with cadmium plated finish

FEATURES: • All steel and stainless steel construction• Rated up to 400 PSI/ WOG• Hexagon cast ends for ease of installation

Marshall Excelsior’s Sight Flow Swing Check Valves are designed with the most durable, impactresistant glass in the industry. This sight flow valve allows bulk plant operators an inspection pointto visually monitor liquid flow conditions which allows the operator to achieve maximum pumpefficiency. They also feature a soft seat swing away check valve which limits flow to one direction.This check valve is usually closed until pressure activates the valve when flow is directed intopiping or containers causing the valve to open. When flow stops or reverses, the check returnsto the closed position minimizing product loss in the event of a line failure.

Installing a sight flow valve upstream of a plant pump, allows the operator to observe product flow and make pump adjustments for maximum flow without the liquid forming vapor bubblescausing uneven flow patterns and significantly reducing efficiency. Additionally, installing a sightflow valve at the loading arm of a plant allows the operator to maintain consistent observationof pump conditions. This valve is suitable for stationary and mobile applications.

Installing this valve on a compressor operation will provide a visual indication of when the tankcar or transport is emptied of liquid and ready for vapor recovery.

ME874S-16

Sight Flow Swing Check Valves Excela-Flange Series MARSHALL EXCELSIOR

Item No. Description Inlet Outlet MatingFlange Type

Weight(lbs.)

ME874S-16 2” - 4 Bolt Double Flange Sight Flow Valve

4 Bolt FlangeType B

4 Bolt FlangeType B A 16.0

* “NC” indicates no check e.i. ME874SNC-16 | Viton® is a trademark of DuPont Performance Elastomers

The ME874S-16 Sight Flow Swing Check Valves feature our new modular Excela-Flange 4-Bolt Inlet/Outlet design that can be easily adapted to both NPT thread or socket weld type A companion flanges (ME840 & ME841 Series) from 1-1/4” - 2” in diameter making it universal to piping sizes within this range. MEC Sight flow valves are designed with the most durable, impact resistant glass in the industry. This sight flow valve allows bulk plant operators aninspection point to visually monitor liquid flow conditions which allows the operator to achievemaximum pump efficiency. They also features a soft seat swing away check valve which limitsflow to one direction. This check valve is usually closed until pressure activates the valve whenflow is directed into piping or containers causing the valve to open. When flow stops or reverses, the check returns to the closed position minimizing product loss in the event of a line failure.

Installing a sight flow valve upstream of a plant pump, allows the operator to observe product flow and make pump adjustments for maximum flow without the liquid forming vapor bubbles causing uneven flow patterns and significantly reducing efficiency. Additionally, installing a sight flow valve at the loading arm of a plant allows the operator to maintain consistent observation of pump conditions. This valve is suitable for stationary and mobile applications. Installing this valve on a compressor operation will provide a visual indication of when the tank car or transport is emptied of liquid and ready for vapor recovery.

• 4 bolt universal inlet/outlet flanges• Specially formulated, large diameter, impact

resistant sight glass with O-ring packing seals for maximum safety and visibility

• Durable ductile iron body with cadmium plated finish for maximum durability

• Integral swing check valve with soft seat for maximum product flow - minimizing product loss in the event of a line failure

FEATURES: • All stainless steel internal components for

maximum corrosion resistance• Standard nitrile seat, available in Viton® or

Kalrez®

• Listed for use with LP Gas and NH3 - 400 PSI/ WOG

• For use with all Type A (ME840 and ME841 Series) companion flanges

Item No. Description Material FlangeMaterial OAL

ME981-6 3/4” FNPT Flow Indicating Check Valve

Ductile Iron

Ductile Iron4-3/4”

ME981-8 1” FNPT Flow Indicating Check Valve 4-3/4”ME981-10 1-1/4” FNPT Flow Indicating Check Valve 5-3/8”ME981-16 2” FNPT Flow Indicating Check Valve Cast Steel 6-7/8”ME981-24 3” FNPT Flow Indicating Check Valve Ductile Iron 9-5/8”ME982-10 1-1/4” FNPT Non-Indicating Check Valve Ductile Iron 5-3/8”ME982-16 2” FNPT Non-Indicating Check Valve Cast Steel 6-7/8”ME982-24 3” FNPT Non-Indicating Check Valve

DuctileIron

9-5/8”ME981-16-2F 2” - 300 lb. Flange Flow Indicating Check Valve 11-7/8”ME981-24-3F 3” - 300 lb. Flange Flow Indicating Check Valve 14-1/8”ME981-24-4F 4” - 300 lb. Flange Flow Indicating Check Valve 14-1/4”ME982-16-2F 2” - 300 lb. Flange Flow Non-Indicating Check Valve 11-7/8”ME982-24-3F 3” - 300 lb. Flange Flow Non-Indicating Check Valve 14-1/8”ME982-24-4F 4” - 300 lb. Flange Flow Non-Indicating Check Valve 14-1/4”

ME981-6

ME982-24-4F

ME875S-3F


107 108

FF

GAUGES & ACCESSORIES

Item No. Propane Capacityand Mounting Style

Nominal Cyli nderDiameter Gauge Head Style Replacement Dial

w/ 2 Mounting ScrewsMES-FG1284-001U

33-1/2 lb. Universal 12”

Junior Brass Head

MES-1284-20-001-KITMES-FG2184-001U Threaded 3/4” NPTBrass Head

MES-FG2284-001U Threaded 1-1/4” NPTBrass Head

ACCU-MAX LPG Float Gauges - FG3981 Series MARSHALL EXCELSIORLift Truck Float Gauge for Dot Horizontal or Vertical Tank Orientation MARSHALL EXCELSIOR

Item No. Replacement Parts Description

MES-1284-21-1 Universal ASME / DOT Lift Truck Float Gauge Dial Screw MES-1284-21-2 Junior Float Gauge Head Gasket

• 1-1/4” NPT or junior head mounting• Junior mounting head includes gasket• Solid brass mounting head -

LPG SERVICE ONLY• Ultra low friction, smooth acting,

non-jamming gear design

FEATURES: • Hermetically sealed, easy to read dial• Teflon® coated, free-floating shaft• Solid float; no metal shell to corrode or leak

MES-FG1284-001ULift Truck Float Gauge

(Junior Head Mounting)

MES-FG2284-001ULift Truck Float Gauge(1-1/4 NPT Mounting)


MES-FG3981 Series1” NPT AG Float Gauges

Gauge Face

ACCU-MAX LPG Float Gauges are for above ground, horizontal tanks and DOT Cylinders with 1” NPT mounting. Refer to ordering information for correct size gauge.

• Remote ready• Solid brass mounting head - LPG SERVICE

ONLY• Ultra low friction, smooth acting,



ACCU-MAX LPG Float Gauges - FG3981 Series MARSHALL EXCELSIOR1” NPT Above Ground Float Gauges for ASME Horizontal Domestic Tanks & Dot Cylinders MARSHALL EXCELSIOR

Item No. Container Capacity(Gallons of Water)

Nominal CylinderDiameter

GaugeStyle Head

Remote ReadyReplacement Dial with

2 Mounting Screws

StandardReplacement Dial with

2 Mounting Screws

MES-FG3981-002R120

24”

Threaded 1” NPTBrass Head

MES-1284-20-002R-KIT MES-1284-20-002-KIT

150

MES-FG3981-003R200

30”250325

MES-FG3981-004R 500 37”MES-FG3981-005R 1000 41”

MES-FG3981-001R* 420# Vertical 30”MES-1284-20-003R-KIT

(% of total volume)

MES-1284-20-003-KIT(% of total volume)


109 110

FF

FG2281Series

FG2281Series

GAUGES & ACCESSORIES GAUGES & ACCESSORIES

ACCU-MAX Remote Ready Float Gauges are for above ground, domestic, horizontal tanks with 1-1/4” NPT mounting. Please refer to ordering information for correct size gauge.

ACCU-MAX LPG Float Gauges - FG3981 Series MARSHALL EXCELSIOR

• Solid brass mounting head - LPG SERVICE ONLY

• Ultra low friction, smooth acting, non-jamming gear design


ACCU-MAX LPG Float Gauges for Above Ground Horizontal Domestic Tanks MARSHALL EXCELSIOR



GaugeStyle Head


2 Mounting Screws


2 Mounting Screws

MES-FG2281-001R120

24”

Threaded 1-1/4”NPT Brass Head

MES-1284-20-002R-KIT MES-1284-20-002-KIT

150

MES-FG2281-002R200

30”250325

MES-FG2281-003R 500 37”MES-FG2281-004R 1000 41”

ACCU-MAX LPG Float Gauges - FG3981 Series MARSHALL EXCELSIORACCU-MAX Float Gauges for ASME Above Ground Horizontal Domestic Tanks MARSHALL EXCELSIOR




2 Mounting Screws


2 Mounting Screws

MES-FG1280-001R120

24”

MES-1284-20-002R-KIT MES-1284-20-002-KIT

150

MES-FG1280-002R200

30”250325

MES-FG1280-003R 500 37”MES-FG1280-004R 1000 41”MES-FG1280-005R 1999 47”MES-FG1280-006R 2000 52”

• Brass junior head mounting• Solid brass mounting head -

LPG SERVICE ONLY• Ultra low friction, smooth acting,

non-jamming gear design• Hermetically sealed, easy to read dial• Teflon® coated, free-floating shaft

FEATURES: • Solid float; no metal shell to corrode or leak• Standard with remote ready dial• Gasket included• Remote ready


111 112

FF

Item No. Type Style Dial Face Dial Size Tank Diameter

ME930-72 Standard Glow/Black 72”ME930-79 Standard Glow/Black 79”ME930-84

DOT Standard Glow/Black

4” 84”

ME930C-72 Classic Silver/Black 72”ME930C-79 Classic Silver/Black 79”ME930C-84 Classic Silver/Black 84”ME940-108 Standard Glow/Black 108”ME940-130

ASME Standard Glow/Black

8” 130”

ME940C-108 Classic Silver/Black 108”ME940C-130 Classic Silver/Black 130”

Item No. Connection Connection

ME931 2-1/2” MNPT 1/2”-13 FemaleME932 Weld 1/2”-13 Female

ME930-72

“Glow” TechnologyStandard Dial

ME930 DOT SeriesClassic Dial

ME931


Accu-Max Limited Warranty: Marshall Excelsior warrants Accu-Max float gauges and repair kits to the originalbuyer to be free of defects in material and workmanship under normal service and use for two years from manufactured date.

Accu-Max Float Gauges MARSHALL EXCELSIOR

Accu-Max Float Gauges are designed to measure liquid levels within horizontal DOT andStationary ASME Tanks with fluid capacities above 2,300 gallons. For maximum gauge life, thefloat arm features an integral spring-loaded shock absorber for harsh over-the-road applications.The standard dial face features a black background for reduced glare with glow technology providing an easy to read “glow in the dark” dial face, perfect for low light situations. An optional classical style dial face is available. These gauges are suitable for use in bobtail, transport, railcar and bulk storage applications.

NOTE: Gauges must be installed on the centerline of the tank’s side or end for accurate readings.

• All stainless steel construction• Welded tube to coupling design for maximum strength and durability• Dial face 100% sealed and argon filled to prevent moisture build-up and fogging• Factory set and precision tuned for superb accuracy

FEATURES: • Dial face and mounting hardware universal with other industry standard gauges• Mounts to all standard 8 bolt tank flange adapters• Custom length tank configurations available upon request for 30” to 300” I.D. tank

Float Gauge Accessories MARSHALL EXCELSIOR

These Float Gauge Accessories are designed for mounting float gauges in DOT or ASME tanks.These zinc plated steel 8 bolt mounting flanges feature 1/2”-13 threads for easy installation.


ACCU-MAX LPG Float Gauges - FG3981 Series MARSHALL EXCELSIORJunior Underground Float Gauges for Underground Horizontal Domestic Tanks MARSHALL EXCELSIOR

• Brass junior head mounting• Solid brass mounting head - LPG SERVICE

ONLY• Ultra low friction, smooth acting,


FEATURES: • Hermetically sealed, easy to read dial• Teflon® coated, free-floating shaft• Solid float; no metal shell to corrode or leak• Gasket included

MES-FG1281 SeriesJunior UG Float Gauges



Gauge HeadStyle

GaugeRiser Lengths


2 Mounting Screws


2 Mounting Screws

MES-FG1281-001R120

24”

JuniorBrassHead

8-1/2”

MES-1284-20-002R-KIT MES-1284-20-002-KIT

150

MES-FG1281-002R

200

30”250

325

MES-FG1281-003R 500 37”

MES-FG1281-004R 1000 41”

MES-FG1281-005R120

24”

15-1/2”

150

MES-FG1281-006R

200

30”250

325

MES-FG1281-007R 500 37”

Item No. Replacement Parts Description

MES-1284-21-1 Universal ASME / DOT Lift Truck Float Gauge Dial Screw MES-1284-21-2 Junior Float Gauge Head Gasket


ME940 ASME Series 8” Dial Shown as

Standard “Glow” Dial


113 114

FF

Item No. Description Dial Face Tank Diameter

ME930WG-72 72”ME930WG-79 DOT Float Gauge Assembly Glow/Black 79”ME930WG-84 84”ME930CWG-72 72”ME930CWG-79 DOT Float Gauge Assembly (Classic) Silver/Black 79” ME930CWG-84 84”ME940WG-108

Stationary Float Gauge Assembly Glow/Black 108”

ME940WG-130 130”ME940CWG-108

Stationary Float Gauge Assembly (Classic) Silver/Black 108”

ME940CWG-130 130”

GAUGES & ACCESSORIES GAUGES & ACCESSORIESAccu-MaxTM Float Gauges Top Mount Series MARSHALL EXCELSIOR

Item No. Description DialFace

DialSize Riser Tank

Diameter Accessories

ME930TM4-108-5946

Accu-MaxStationary ASMETop Mount Gauge

Glow/Black

4” 4” 108”ME931

2-1/2” MNPT Flange Adapter

ME932Weld Type Flange

Adapter

ME930TM8-108-6346 4” 8” 108”ME930TM4-130-7056 4” 4” 130”ME930TM8-130-7456 4” 8” 130”ME940TM4-108-5948 8” 4” 108”ME940TM8-108-6348 8” 8” 108”ME940TM4-130-7060 8” 4” 130”ME940TM8-130-7460 8” 8” 130”

Custom configurations available upon request.

Accu-Max Float Gauges Top Mount Series measure liquid levels within horizontal StationaryASME Tanks with fluid capacities above 2,300 gallons. Suitable for use in bulk storage vesselsequipped with either 2-1/2” NPT 6000 lb. or 8 bolt 3-1/2” on center tank openings located on the top of the vessel such as underground or buried applications.

• All stainless steel construction for use with LPG and NH3 applications

• Welded tube to coupling design for maximum strength and durability• Integral spring-loaded shock absorber for

arduous over-the-road application• Exclusive easy to read “glow in the dark”

dial face perfect for low light situations• Dial face 100% sealed and argon filled to

prevent moisture build-up and fogging

FEATURES: • Easy to assemble• Factory set and precision tuned for superb

accuracy• Dial face and mounting hardware universal

with other industry standard gauges• Mounts to all standard 8 bolt tank flange

adapters• Custom configurations available upon

request

ME930TMASME Series

4” Dial

ME940TMASME Series

8” Dial

Accu-Max Limited Warranty: Marshall Excelsior warrants Accu-Max float gauges and repair kits to the originalbuyer to be free of defects in material and workmanship under normal service and use for two years from manufactured date.

Trans-Max DOT & ASME Stationary Float Gauges MARSHALL EXCELSIOR

Accu-Max Float Gauges Trans-Max Series measure liquid levels within horizontal DOT and Stationary ASME Tanks with 1” FNPT tank gauge port openings. Designed to replace rotary stylegauges in tanks with fluid capacities greater than 2,300 gallons. Suitable for use in bobtail, transport, and bulk storage applications. Marshall Excelsior’s exculsive “wedge” designallows for easy installation while greatly reducing time spent inside the vessel.

NOTE: The heavy duty design of this gauge requires entering vessel through manway during installation.

• All stainless steel construction for use with LPG and NH3 applications

• Welded tube to coupling design for maximum strength and durability• Installation requires manway • Converts rotary style gauge to heavy duty

Accu-Max style for both mobile and stationary applications• Integral spring-loaded shock absorber for

arduous over-the-road application• Easy to read flow indicator with “Glow” arrow shows if valve is open/closed

FEATURES:

• Easy to assemble• Dial face 100% sealed and argon filled to

prevent moisture build-up and fogging• Factory set and precision tuned for superb

accuracy• Dial face and mounting hardware universal

with other industry standard gauges• Mounts to all standard 1” NPT tank coupling adapters• Custom lengths available upon request• Available with classic style dial face

ME930WG DOT SeriesME940WG ASME Series

Patent PendingWand


115 116

FF

Item No. Tank Type Junior Head 3/4 NPT 1-1/4 NPT Size No. Service

JD060A — TD060A 20, 33, 43 Horizontal JU160B UU160B TU160B 33 Universal JU212A UU212A TU212A 43 Universal JA216A — — 43 Vertical JU086B — TU086B 20 Universal

Item No. Tank Tank Junior Senior Screw In 1” Screw In 1-1/4” Size No. Diameter

JA124l — — TA130AP Horz 420# 24 JA154A SA160A HA156AP* TA156AP* 250, 330 30 JA192J SA194A HA194AP TA194AP 500 37 JA206l SA214A HA210AP TA210AP 1000 41 JA250J SA230E HA254JP TA254NS Vert 420# 30

Item No. Dial Size Description

13000S Junior Squibb 130010 Senior Squibb 130005 Junior Squibb Kit 130010 Senior Squibb Kit 130101 Junior JR Blank Flange 130104 Senior SR Blank Flange

Item No. Part No. Tank Diameter

131825 RM1425 56” 131830 RM2030 66” 131833 RM1833 72” 131834 RM1834 74” 131836 RM1836 78”-79” 131832 RM2437 80” 131838 RM2438 82”- 84” 131840 RM2440 85”- 86” 131941 RM2941 87” 131841 RM1841 88” 131842 RM2942 90” 131245 RM3245 96”


Domestic Gauge TAYLOR PRODUCTS

*Denotes drop in dial

Universal Dial Kits TAYLOR PRODUCTS

Road Master Gauges TAYLOR PRODUCTS

Float Gauges for Lift Truck Cylinders TAYLOR PRODUCTS

JU160B

JA1241

130005

130010

ORDERING INFORMATION for other gauges and pressure vessel gauges

If the code is not easily visible, specify the followingwhen ordering:

1. Type of Service - LP-Gas or Anhydrous Ammonia (NH3).

2. Gauge Size or Head Type - Specify Junior Size, Senior Size, Visible “4”, 3/4” Threaded, 1” Threaded, 1-1/4” Threaded, Roadmaster or Master Gauge Model (4 bolt or 8 bolt).

3. Type Mounting - Top, side, end, or angle (if angle, specify angle above horizontal center line).

4. Provide Dimensions

H = Distance from tank surface to gasket surface. D = Inside diameter of tank or cylinder.

5. Dimensions for Vertical Cylinders only:

X = Distance from center of adaptor to nearest inside wall. O = Cylinder height. H = Distance from tank surface to gasket surface.

Junior Head - 4 Bolt Senior Head - 4 Bolt

2-1/2Bolt

Circle2-1/32Bolt

Circle

GAUGESIZE

MOUNTING LOCATION

“H” Dimension

“H”

“H”(Top Mount)

(AngelMount)

(End Mount)

(Side Mount)

Hemispherical

Semi-Ellip. DistanceAngle

HorizontalCenterline

“X” Distance

VERTICAL DOT

“O” Height

“H” Dimension

Footing

Road Master Gauge

ORDERING INFORMATION for Taylor Products - Visible GaugesOrder Visible Gauges by their code/item number. Code/item numbers are stamped on the heads of all gauges. Gauges produced before 2008 are stamped on the top of the head andthose produced after 2008 are stamped on the sides of the head.

Old Style

Location ofcode/item number

New Style


Rotary Gauge System CAVAGNA GROUP

117 118

F F

Item No. Nominal Diameter Tank Container Capacity Dimension (mm)

Ø Inches Ø mm Type Gallons Liters A B2069.U 24” 609.60 120 454.25 338 2852070.U 30” 762.00 250/320 946.35/1,211.328 412 3602071.U 37” 939.80 Horizontal 500 1,892.70 510 4382072.U 41” 1,041.40 1,000 3,785.40 553 4772073.U 48” 1,219.20 — — 612 5352075.U 30” 762.00 Vertical — — 640 430

Item No.

Nominal Diameter Tank Container Capacity Dimension (mm) Container Ø Inches Ø mm Type Gallons Liters A B Connection

2069.U1 24” 609.60 120 454.25 338 285 2070.U1 30” 762.00 250/320 946.35/1,211.328 412 360 2071.U1 37” 939.80 Horizontal 500 1,892.70 510 438 2072.U1 41” 1,041.40 1,000 3,785.40 553 477 2073.U1 48” 1,219.20 — — 612 535 1”2075.U1 30” 762.00

Vertical — — 640 430

2076.U1 — — — — 560 477 20SO.U1 — — Horizontal — — * * 20SV.U1 — — Vertical — — * * 2069.U1-1/4 24” 609.60 120 454.25 338 285 2070.U1-1/4 30” 762.00 250/320 946.35/1,211.328 412 360 2071.U1-1/4 37” 939.80 Horizontal 500 1,892.70 510 438 1-1/4”2072.U1-1/4 41” 1,041.40 1,000 3,785.40 553 477 2073.U1-1/4 48” 1,219.20 — — 612 535

Length in Inches Model (Diameter of Tank) Number

68 O-31 L - 68 69 - 92 O-31 L - 69-92 93 - 108 O-31 L -93-108 109 - 140 O-31L -109-140 Dial only LP O-323

Item No. Part No. Tank Diameter

131900 EL4442 42” 131901 EL6046 46” 131902 EL6048 48” 131903 EL6056 56” 131906 EL6060 60” 131909 EL7266 66” 131912 EL7272 72” 131914 EL8474 74” 131916 EL8476 76” 131919 EL8479 79” 131920 EL8480 80” 131921 EL8481 81” 131922 EL8482 82” 131923 EL8484 84” 131925 EL8486 86” 131926 EL8487 87” 131930 EL9696 96”


All Level Gauges are produced in compliance with the CEN TC 286-prEN 13799 standard. The float is made in SPANSIL rubber. This kind of material cannot be detached from its lodging whenin touch with caustic soda. These level gauges have been manufactured in accordance with thebest available technology: a tropicalized zamac has been used both for the head and the gearing.

Float gauges flanged four bolt models include a mounting.

LPG Float Gauges Flanged Four Bolt Model CAVAGNA GROUP

LPG Threaded Float Gauges CAVAGNA GROUP


Cavagna Group rotary gauges can be used on stationary or mobile tanks to visually indicate the amount of LP-Gas in the container. They are also used in filling the tank to the proper liquid level. On mobile applications and some large stationary storage tanks, hangers are recommended to support the horizontal length of the dip tube.

The gauge is operated by opening the small bleed orifice when the tube is in the vapor space of the tank. Moving the pointer on the dial causes the end of the tube to move until it contacts liquid in the container. At that point, discharge from the bleed orifice turns from vapor to liquidand the rotary gauges dial gives the volume percentage of liquid in the tank.

Gauges fit 1” coupling container connections. All gauges have stem and dip tubes with an extra large inside diameter. This assures that the correct liquid level can be obtained quickly.

Eliminator™ Direct-reading Float Gauge TAYLOR PRODUCTS

The Eliminator™ Direct-reading Float Gauges are used to determine when the maximum filllevel has been reached in large tanks up to 96”. These gauges are not to be used in filling tanks.

Eliminator™ Gauge

Back ofEliminator™ Gauge


119 120

GG

Motor

Pump Delivery in GPM Item No. Description

Size* Speed 50 PSI 100 PSI

(RPM)** DIFF DIFF 2LGLD2VB7.5

2” Base Mounted with V-Belt Drive 7.5 HP 660, 520 67, 50 57, 41

2LGLD2VB5 5 HP 420, 330 40, 30 30, 233LGLD3VB15

3” Base Mounted with V-Belt Drive 15 HP 640, 520 133, 108 112, 84

3LGLD3VB10 10 HP 420, 330 80,59 60,42

4LGLD4VB20 20 HP 640 270 220

4” Base Mounted with V-Belt Drive

520 220 180 4LGLD4VB15

15 HP

420 170 130 330 130 90


Capacity Inlet Discharge Range (GPM)

LGL158A 1-1/2” Foot Mounted 17 - 32 2”, 300# Flanged 1-1/2”, 300# Flanged

Capacity Pump Delivery in GPM Item No. Description Range Speed 50 PSI 100 PSI (GPM) (RPM) DIFF DIFF

LGF1 1” Flanged Mounted 2 - 10 1750 8 6

LGB1 1” Bracket MountedLGF1P 1” Flanged Mounted

5 - 15 1750 13 10LGB1P 1” Bracket Mounted

Appox. Delivery in GPM Item No. Description

Motor Motor 50 PSI 100 PSI

Size (HP)

Speed DIFF DIFF

1LGF11 1 1750 8 6

1LGF1P1 1” Flanged Mounted1LGF1P1.5 1.5 1750 13 10

Standard Pump Delivery in GPM Item No. Description Motor Speed 50 PSI 100 PSI Size (HP) (RPM) DIFF DIFF 1LGB1D1 1” Bracket Mounted 1

1750 8 6

LGL150 1-1/2” Foot Mounted 1.5 13 10

Standard Pump Delivery in GPM Item No. Description Motor Speed 50 PSI 100 PSI (GPM) (RPM) DIFF DIFF

3LGL125D2 1-1/4” Foot Mounted 2 1750

21 183LGL150D3 1-1/2” Foot Mounted 3 33 29

Capacity Pump Delivery in GPM Item No. Description Range Speed 50 PSI 100 PSI (GPM) (RPM) DIFF DIFF LGL125 1-1/4” Foot Mounted 15 - 25

1750 21 18

LGL150 1-1/2” Foot Mounted 25 - 35 33 29

PUMPS PUMPS

The LGF Series Pumps mount directly to standard C-face, 1750 rpm motors with flexible coupling. They are UL Listed and are suitable for continuous duty. An explosion-proof switch forremote mounting is provided.

1-1/4” and 1-1/2” Pump Assemblies with Base Mounting BLACKMER

The 3LGL125D2 and 3LGL150D3 is the foot-mounted version of the LGL125 and LGL150 Series Pumps. The pump is mounted to a steel baseplate and furnished with a flexible shaft coupling and connected to a standard motor. A coupling guard is included. Listed motors are three phase and explosion-proof.

1-1/4” and 1-1/2” Pumps BLACKMER

Blackmer’s 1-1/4” and 1-1/2” Pumps offer higher capacities than the LFG1/B1 Series pumps. They are suited to a variety of small transfer jobs, but are especially popular for multi-purpose cylinder-filling systems.

2”, 3” and 4” Pump Assemblies with Base Mounting BLACKMER

1” Pumps BLACKMER

Blackmer’s 1” Pumps are ideal for cylinder-filling, motor fueling and for supplying smallvaporizers. These pumps are fitted for both LP-Gas and anhydrous ammonia service.

1” Pump Assemblies with C-Face Mounting BLACKMER

1” Pump Assemblies with Base Mounting BLACKMER

LGB Series Pumps have brackets for foot mounting to a conventional baseplate. Motors orderedfor these units are furnished to customer specifications. Standard motors listed here are singlephase and explosion-proof.

*Recommended motor size | **With 1750 RPM Motor

Blackmer’s 2” and 3” Pump Assemblies with Base Mounting units have high-torque V-belts and quick disconnect sheaves. Units come complete with belt guard, pump mounted to base plate, and mounted to standard motor.

The 4” Pump Assemblies with Base Mounts have high-torque V-Belts and quick disconnect sheaves. Sheaves and hubs are a two-part assembly that comes apart easily. Units come complete with belt guard, pump mounted to base plate, and mounted to standard motor.

1-1/2” High Pressure LPG Pump BLACKMER

LGL158A

LGL125FG1281 Series

LGL Series

LGF Series

LGB Series

3LGLD3VB10

• Single and dual hose fuel dispenser

• Aerosol filling

• Vaporized feed• Underground tank applications

• Above ground tank applications• Other high differential pressure liquefied

gas applications

APPLICATIONS:


121 122

GG

Delivery in GPM Capacity Pump Item No. Description

Range Speed 50 PSI HP 100 PSI HP (GPM) (RPM) DIFF REQD. DIFF REQD.

650 93 5.0 81 7.9

TLGLF3 3” Flange

40 - 93 600 85 4.5 73 7.0

Mounted 500 70 3.6 59 5.7 400 52 2.8 40 4.5

Capacity Pump Delivery in GPM Item No. Description Range Speed 50 PSI 100 PSI (GPM) (RPM) DIFF DIFF

640 270 220

LGLD4

4”Foot Mounted

90 - 270 520 220 180

420 170 130 330 130 90

Delivery in GPM Capacity Pump Item No. Description

Range Speed 50 PSI HP 100 PSI HP

(GPM) (RPM) DIFF REQD. DIFF REQD.

650 280 15.5 245 25.0

TLGLF4 4” Flange

120 - 280 600 260 14.3 220 23.0

Mounted 500 210 11.9 170 19.0 400 160 9.5 120 15.2

Capacity Pump Delivery in GPM Item No. Description Range Speed 50 PSI 100 PSI (GPM) (RPM) DIFF DIFF LGLD2 1-1/4” Foot Mounted 23 - 67 660 67 57LGLD3 1-1/2” Foot Mounted 42 - 133 640 133 112

The TLGLF3 Series Pump flange mounts directly to the truck tank in combination with the flanged internal control valve. Because it eliminates the intake line and related restrictions to flow, it also eliminates the cavitation problems caused by them. That means longer pump life and higher effective pump capacity.

3” Truck Pump BLACKMER

PUMPS PUMPS4” Truck Pump BLACKMER

The TLGLF4 Series Transport Pump is designed to mount to 4” internal valves. It is suitable forboth LP-Gas and anhydrous ammonia service. Ideal intake conditions assure maximum pumpingrates and the shortest possible transport turnaround time.

TLGLF3

LGLD4

TLGLF4

The 2” and 3” Double Ended Shaft Pumps are ideal for bulk plant service, multiple cylinder filling applications, vaporizers, bobtails, and transports.

2” and 3” Pumps - Double Ended Shaft BLACKMER

LGLD2

For more information on Blackmer productsor installation instructions contact your

MTankCo. representative.

4” Pump - Double Ended Shaft BLACKMER

The LGLD4 Pump Series is suitable for handling both LP-Gas and anhydrous ammonia. These models are used in bulk plant applications where high transfer rates are desirable.

Item No. Description Capacity Range (GPM) Inlet Discharge

RC20 Regenerative 13.21 GPM DN 25/1” NPT(F) DN 25/1 in. NPT(F)RC25 Turbine 23.78 GPM DN 25/1” NPT(F) DN 25/1 in. NPT(F)

RC40 Pump 52.8 GPM1-1/2” NPT, Flanged to suit 1-1/2” ANSI Class

300 and DN40 DIN PN40

1” NPT, Flanged to suit 1” ANSI Class 300 and DN25 DIN

PN40

Regenerative Turbine Pumps for Liquefied Gas Applications BLACKMER

RC25The Ebsray Model RC20 & RC25 Regenerative Turbine Pumps are designed and precision-built for high-pressure transfer of LPG, autogas, propane, butane, DME and anhydrous ammonia.

The Ebsray Model RC240 Regenerative Turbine Pumps are single-stage regenerative turbine pumps designed for handling LPG and other gaseous liquids including Autogas, DME, Aerosols,CO2, Industrial refrigerants and Anhydrous ammonia.

RC40


123 124

GG

Ref Part Part Name

Parts Per No. No. Pump

108B 833000 Bracket (C-faced footed) – LGF1(P)D 1

Ref Part Part Name


2 432901 Adjusting Screw – Relief Valve (R/V) 1 3 922811 Locknut – Adjusting Screw 1 4 412901 Cover – R/V 1 4A 7119401 O-ring – Spring Guide 1 7 422901 Spring Guide – R/V 1 8 472901 Spring – R/V 1 9 452901 Valve – R/V 1 9A 442901 Disc – R/V 1 10 7019651 O-ring – R/V Cover 1

123 022914 Cylinder – LGF1, LGB1 1

022915 Cylinder – LGF1P, LGB1P

13 262907 Rotor and Shaft Assembly, Six Vane 2

1 (Includes Ref. Numbers 24A and 24B) 14 0929131 Vane – Duravane (Std.)3 4, 6 20† 032905 Head 1 21 920178 Capscrews – Head 4 24 9034051 Ball Bearing 2 24A 903531 Locknut – Bearing 2 24B 9035321 Lockwasher – Bearing 2 263 3830751 Gasket – Bearing Cover 1 273 043071 Bearing Cover 1 283 920080 Capscrews – Bearing Cover 4

Ref Part Part Name


28A3 920090 Bracket Mounting Screws 4 28B3 920101 Bracket Mounting Screws 4 28C 920026 Guard Screw 1 34 906150 Coupling Half – Pump 1 34 906151 Coupling Half – Motor (56C) 1 34 906147 Coupling Half – Motor (143-145TC/184C) 1 34 906155 Coupling Spider 1 35 9091261 Key – Shaft 1 72 7119411 O-ring – Head 1 73 908198 Gage Plug (1/4”) 2 73A3 908225 Gage Plug (3/4”) 1 76 317815 Grease Fitting 2 76A 701992 Grease Relief Fitting 2 104 3319341 Grease Seal 1

108 832913 Bracket - (Base Mount) - LGB1(P)D

1 832912 Bracket (C-Faced Footless) - LGF1(P)D 108A 920331 Capscrews – Bracket 4 108B — Bracket (C-Faced Footed) 186 804120 Guard 1 903090 Tool - Locknut 898916 Kit – Maintenance (4-Vane) 898994 Kit – Maintenance (6-Vane)

Ref Part Part Name


153 3329201 Mechanical Seal Assembly 2153A1 332922 Jacket Assembly – Seal 2153B1 332901 Stationary Seat (Steel) 2153D 711916 O-ring – Stationary Seat (Buna-N) 2153F1 332902 Seal Face (Carbon) 2153G 711939 O-ring – Rotating (Buna-N) 2

PUMPS PUMPS

Blackmer Parts List for pump models:LGF1E, LGB1E, LGF1PE, LGB1PE, LGF1D, LGB1D, LGF1PD, LGB1PD, LGF1C, LGB1C, LGF1PC, LGB1PC

1Included in Maintenance Kit | * Reference numbers 153A, 153B, and 153F are not available

Blackmer Mechanical Seal Parts List for pump models:LGF1E, LGB1E, LGF1PE, LGB1PE, LGF1D, LGB1D, LGF1PD, LGB1PD, LGF1C, LGB1C, LGF1PC, LGB1PC

Pump Parts List BLACKMERPump Parts List BLACKMER Pump Parts List BLACKMERPump Parts List BLACKMER

Mechanical Seal Mounting Bracket

Pump Parts - Mechanical Seal BLACKMER Pump Parts - Mounting Bracket BLACKMER

1 Included in Maintenance Kit | 2 Discontinued ‘D’ and ‘C’ models shipped with a 4-vane rotor. The current 6-vane rotor is fully interchangeable as long asthe slotted vanes (pn 092913) are used. The current slotted vanes (pn 092913) may be used in either the 6-vane or 4-vane rotors. The discontinuedsolid vanes may be used in the 4-vane rotors ONLY. Always install the vanes with the slot facing the direction of rotation. | 3 To fit the LGB1(P)C, LGF1(P)C use: Ref. No. 12-022902/022911 respectively, Ref. No. 20-032902, Ref. No. 26-382901, Ref. No. 27-042901, Ref. No. 28-920203, Ref. No. 28A and B-920230, Ref. No. 73A-908198, and Ref. No.108-832901/832905 respectively.


125 126

GG

Mechanical Seal Parts for Pump TLGLF3C BLACKMER

1 Included in Maintenance Kit and Rebuild Kit | **Mechanical Seal Ref. No. 153 is only sold as a complete assembly. Ref. No. 153A, 153B, and 153C are not available as separate replacement parts.

Ref Part Part Name


4 415108 Cover - Relief Valve (R/V) 1 5 920331 Capscrew - R/V Cover 6 8 4714281 Spring - R/V 1 9 451417 4 Valve - R/V 1 10 7019191 O-ring - R/V Cover 1 12 015128 Casing 1 13 265147 2 Rotor and Shaft Assembly5 1 14 0951321 Vane - Duravane 6 20 035132 Head 2 21 920351 Capscrews - Head 36 24 9031561 Ball Bearing 2 24A 9035212 Locknut - Bearing 2 24B 9035221 Lockwasher - Bearing 2 26 3839401 Gasket - Bearing Cover 2 27 041431 Bearing Cover 2 28 920285 Capscrews - Bearing Cover 8 35 9091301 Key - Shaft 1 41 1851012 Liner 1 652010 Flange - 2” NPT 1-2 652024 Flange - 2” Slip-on Weld 1-2 42 655100 Flanged Elbow - 2” NPT 1-2 655109 Flanged El - 2” Socket Weld 1-2 652036 Blank Flange for Auxiliary Inlet 1-2

Ref Part Part Name


42A 7020041,3 O-ring–Flange 2-5/8” x 2-7/8” (current) 2

7019191 O-ring–Flange 2-1/2” x 2-3/4” (older pumps) 2 42B 920491 Capscrew - Flanges 8 71 0651211 Disc 2 72 7119231 O-ring - Head 2 73 908198 Gage Plug 2 74 1851932 Key - Liner 1 76 317815 Grease Fitting 2 76A 701992 Grease Relief Fitting 2 77 1216071 Push Rod 3 104 3319181 Grease Seal 2 123 7014801 Dirt Shield 2 186 341601 Shaft Protector 1 — 903091 Tool - Locknut — — 898980 Kit – Maintenance — — 899225 Kit – Maintenance with R/V — — 899080 Kit – Rebuild — — 899125 Kit – Rebuild with R/V —

1 Included in Maintenance Kit and Rebuild Kit | 2 Included in Rebuild Kit3 Larger O-ring introduced October 2002 | 4 Additional parts included in Kits with R/V | 5 Includes reference number 24A and 24B

Ref Part Part Name


153 3329201 Mechanical Seal Assembly 2 153A ** Stationary Seat (Steel) 2 153B ** Seal Face (Carbon) 2 153C ** Jacket Assembly 2 153D 711924 O-ring - Stationary (Buna-N) 2 153E 711918 O-ring - Rotating (Buna-N) 2

Ref Part No. Part No. Parts

No.

1-1/4” Hyd 1-1/4” Hyd Part Name Per Motor Shaft Motor Shaft Pump

* 891458 891205 Hydraulic Motor Adapter Kit *26A 383940 383940 Gasket – Hydraulic Motor Adapter 128A 920369 920369 Capscrew – Hydraulic Motor Adapter/Head 434 906967 906966 Coupling w/ Setscrew Straight Key Hyd. Motor Shaft 135 909184 N/A Key – Coupling 176 317815 317815 Grease Fitting 176A 701992 701992 Grease Relief Fitting 1135 041828 041827 Hydraulic Motor Adapter –SAE A Flange 1135A 920510 920510 Capscrew – Adapter/Motor 2

*Hydraulic Motor Adapter Kits shipped prior to Spring 2002 were a two two-piece design.

MechanicalSeal Parts

Optional HydraulicMotor Adapter Parts

PUMPS PUMPSPump Parts List for Pump Model TLGLF3C BLACKMER

Optional Hydraulic Motor Adapter Parts for Pump TLGLF3C BLACKMER

GG


127 128

C-Models On-Off FNPT FNPT

Gal/Min Item No.

Switch Inlet Outlet at 50 lb.

HP PH Volts Differential

C-10 1 1-1/4” 6.5C-12 1 1 115/230 Yes

1” 15

C-13 2 1-1/2” 22C-14 3 3 230/460 No 32

Item No. FNPT Inlet FNPT Outlet

Gal/Min at 20 lb. Differential

F-10 1-1/4” 12 F-12

1” 19

F-13 1-1/2” 27.5 F-14 38

Pump Differential Approximate Delivery Brake HP Pump Torque Item No. Speed Pressure of Propane* Required Required RPM PSI (KPA) GPM (L/Min) BHP (KW) T•LB (N•M) 750 50 (345) 112 (424) 6.2 (4.6) 43.4 (58.9) 750 100 (689) 99 (375) 9.9 (7.4) 69.3 (94.0) 650 50 (345) 95 (360) 5.2 (3.9) 42.0 (57.0) 650 100 (689) 84 (318) 8.2 (6.1) 66.3 (89.9) 600 50 (345) 86 (326) 5.0 (3.7) 41.3 (56.0) 600 100 (689) 76 (288) 7.8 (5.9) 64.8 (87.9) 500 50 (345) 70 (265) 3.8 (2.8) 39.9 (54.1) 500 100 (689) 62 (235) 5.8 (4.3) 60.9 (82.6)

*Delivery times are approximate

Pump Differential Approximate Delivery Brake HP Pump Torque Item No. Speed Pressure of Propane* Required Required RPM PSI (KPA) GPM (L/Min) BHP (KW) T•LB (N•M) 750 50 (345) 369 (1,397) 12.5 (9.3) 87 (118.0) 750 100 (689) 325 (1,230) 25.1 (18.6) 175 (237.3) Z4200 650 50 (345) 316 (1,196) 10.8 (8.0) 87 (118.0) 650 100 (689) 278 (1,052) 21.7 (16.1) 175 (237.3) 600 50 (345) 289 (1,094) 9.9 (7.3) 87 (118.0) 600 100 (689) 254 (961) 20.0 (14.8) 175 (237.3) 500 50 (345) 236 (893) 8.3 (6.2) 87 (118.0) 500 100 (689) 208 (787) 16.7 (12.4) 175 (237.3)

Corken’s LPG Coro-Flo® “C” Model Series are regenerative turbine liquid pumps with NPT or 300# ANSI flange connections. They are for cylinder filling, bottle filling, and dispenser cabinet applications.

• Handles liquefied gasses without flashing• Floating impeller has long life and low

maintenance

FEATURES:

Coro-Flo ‘C’ Model CORKEN

TECHNICAL SPECIFICATIONS: Inlet: C10: 1-1/4” NPT, C12 through C14: 1-1/2” NPT, 300# ANSI optional; Outlet: 1” NPT, 300# ANSIoptional; RPM: 3450 @ 60 Hz, limited use in 50 Hz @ 2880 RPM; Max. Working Pressure: 400 PSIG (27.6 bar); Max. Differential Pressure: C10: 75 PSIG (5.2 bar), C12: 100 PSIG (6.9 bar), C13,C14: 125 PSIG (8.6 bar); Driver Range: 1 - 3 hp (0.75 to 2.2 kW); Temperature Range: -25° to 225° F (-32° to 107° C); Flow Range: 3 to 8 GPM (7.6 to 136.3 L/min)

• Heavy duty bearings• Space saving compact design

• Handles liquefied gasses without flashing• High flows and differential pressures are

ideal for dual hose and multiple dispensers• Heavy duty bearings

FEATURES:

TECHNICAL SPECIFICATIONS: Inlet: F/DS/DL 9 through 10, 1-1/4” NPT; F/DS/DL 12 through 14, 1-1/2” NPT; 1” NPT, 1” or 1-1/2” 300#ANSI optional; Outlet: 1” NPT, 300# ANSI optionaI; RPM: 3450 @ 60 Hz, 2880 @ 50 Hz; Rotation: Clockwise only; Max. Working Pressure: 400 PSIG (27.6 bar); Max. Differential Pressure: 150 PSIG (10.3 bar)1; Optional Driver range: 1 - 10 hp (0.75 to 7.5 kW); Temperature Range: -25° to 225° F (-32° to 107° C); Flow Range: 2 to 36 GPM (7.6 to 136.3 L/min); Maximum Viscosity: 400 SSU (88 cSt)

• Single mechanical seal allows easy replacement and maintenance• Floating impeller has long life and low maintenance

Corken’s LPG Coro-Flo® “F” Model Series are regenerative turbine liquid pumps with NPT or 300# ANSI flange connections. The pumps are either foot mounted (F-Models) or direct mounted (DS- or DL- Models). Applications for these pumps include under and aboveground, autogas dispensing, multiple cylinder filling stations, vaporizer feed-high pressure, and direct, high pressure asphalt burner feed.

Coro-Flo ‘F’ Model CORKEN

Z3200 and ZH3200 Truck Pumps CORKEN

Z3200 and

ZH3200

Corken’s Z3200 and ZH3200 Model Series control thrust loads and cavitation to ensure extendedpump life. The Z pump thrust bearing design is rated up to 4,000 lb. of thrust. These pumps lastlonger, are superiorly quiet, and need service less often than other pumps because of their newmaterials and design.

*Delivery times are approximate

Z4200 Truck Pumps CORKEN

The Z4200 Truck Pump is used on transports requiring capacities of 200 - 400 GPM. It is designed with 300 lb. ANSI flanges for maximum strength. The belly-mount flange design minimizes cavitation and increases pumping efficiency.

C-Model

F-Model

Z3200

Z4200

PUMPS PUMPS

GG


129 130

Item No. Inlet Outlet Internal Relief Shipping Weight

521E 2”, 2-1/4” 2”, 2-1/2”, 1-1/2” Yes 132 lb.

Item No. Inlet Outlet Mounting Shipping Weight

FF075 1-1/2” ANSI 1” ANSI Frame Mount 63 lb.

FF150

RPM Gal/Min (5 HP Motor) Differential Pressure

20 40 60 80 100

420 38 34 31 28 25520 50 47 43 40 36640 63 58 55 51 —780 77 72 67 — —950 97 — — — —

RPM

Temperature

Maximum

Maximum Maximum Flow Item No.

Range

Range

Working Differential Driver Range

Pressure Pressure Size

Z3500 420 – 800 -25° – 225°F 400 PSIG 150 PSID 20 HP 52–197 PGM Z4500 420 – 800 -25° – 225°F 400 PSIG 125 PSID 25 HP 197–382 PGM

Z3500

Z4500

E21E

FF150

FF075

• Large diameter non-metallic pins allows higher RPM operation

• Easy inspection and maintenance• Cam and blades are made of high tech

materials, extending the life of the pump• Reversible side-plates add twice the life

Z3500 AND Z4500 FEATURES: • Patented needle roller thrust bearings rated

for 4,000 lb. minimizing sideplate wear• No field adjustment is required• Up to 7% or more capacity at 640 RPM• Rated up to 800 RPM• Replaceable liner

PUMPS PUMPS

NOTE: Add “103” after the prefix Item Number to indicate baseplate-motor slide base, v-belt, and pulleys with belt guard, i.e. 521E103.

• Floating rotor requires no adjusting or shims• Hydraulically actuated vanes• O-ring gasket construction• Ductile iron pump body• Self-adjusting sliding vanes

FEATURES: • No troublesome pins or springs behind blades• Run up to 950 RPM• Replaceable liner

Corken’s Coro-Vane® Pumps are positivedisplacement pumps typically used for cylinderfilling, loading and unloading of bulk trucks, and transport trailers. They produce amaximum differential pressure of 125 PSIG.

Corken’s FF075 and FF150 Series are are positive displacement pumps. They produce amaximum differential pressure of 125 PSIG and are typically used for cylinder filling, loading andunloading of bulk trucks, and transport trailers. These pumps have the option of belt drive or gear drive with reducer.

• Stainless steel impeller, sleeve, seal housing, and shaft

• Ductile iron pump body and rotors

FEATURES: • Self-adjusting sliding vanes• Run up to 950 RPM• Replaceable liner

The Z3500 Stationary and Truck Pump is a 3” pump designed for stationary and foot mounted truck applications. It has a locked rotor design to ensure long pump life and excellentperformance. With higher flow rates than other 3” pumps, the Z3500 retrofits Corken’s and other competitive pumps with little or no change in piping. The Z3500 Pump is used for loadingand unloading single and dual bobtails and road tankers.

The Z4500 Stationary Pump is a 4” pump designed for transport loading and multiple bobtail loading applications. If you have two or more bulkheads to load bobtails and transports and would like to shorten your fill times, then the Z4500 is the stationary pump for you. The Z4500 can fill two 3,000 gallon bobtails in 20 minutes or less at typical operating RPMs.

Coro-Vane® Stationary Pump “Z” Series CORKENCoro-Vane® Stationary Pump 521E Series CORKEN

Coro-Vane® Stationary Pump “FF” Series CORKEN


131 132

GG

Coro-Vane® LPG “Z” Series Pump Repair Kits CORKEN

Part Description

Z200 Z3200 Z3500 Z4200 and Z4500 Repair Kit No. 3193X1 Repair Kit No. 3195X1 Repair Kit No. 3195X2 Repair Kit No. 3197X1

Seal Assembly (Qty) 4431XA2 (2) 4431XA2 (2) 4431XA2 (2) 4464XA2 (2)Roller Bearing (Qty) 2754X (2) 2754X (2) 2754X (2) 4460X (2)Outer Race — — — —Thrust Bearing (Qty) 4432 (2) 4432 (2) 4432 (2) 4453 (2)Thrust Bearing Mtg Ring (Qty) 4435 (2) 4435 (2) 4435 (2) 4454 (2)Grease Seals (Qty) 4441 (2) 4441 (2) 4441 (2) 4463 (2)Blades/Vanes (Qty) 4428 (6) 4232 (6) 3936 (6) 4448 (6)Blade/Vane Driver (Qty) 4262X (3) 4262X (3) 5554X (2) 4449X (5)Sideplates (Qty) *4427 (2) *4231 (2) *3938 (2) *4446 (2)Case O-ring (Qty) *2-261A (2) *2-262A (2) *2-268A (2) *2-270A (2)Inlet Flange O-ring 2-231A — *2-259A —Aux Inlet Flange O-ring — — — 2-234AOutlet Flange O-ring (Qty) 2-231A (2) 2-234A (2) *2-245A 2-231AR Valve Cap O-ring 2-224A 2-224A 2-228A 2-234ABearing Cap Shim (0.002) (Qty) 4439 (8) 4439 (8) 4439 (8) 4458 (8)Bearing Cap Shim (0.010) (Qty) 44391 (2) 44391 (2) 44391 (2) 44581 (2)Bearing Cap Shim (0.020) (Qty) 44392 (2) 44392 (2) 44392 (2) 44582 (2)Shaft Key 2270 2270 2270 4459Cam/Liner *4414 *4242 *5539 *4443Rotor and Shaft 4430X2R *4495X2R *12081X6R *4444X2

Part Description

521E Stationary Pump Repair Kit No. 2904X2

Seal Assembly (Qty) 1769XRA (2) Bearings (Qty) 2754X (2) Grease Seals (Qty) 1358 (2) Blades/Vanes (Qty) 1168-7 (10) Sideplates (Qty) 1163-2 (2) Case O-ring (Qty) 2-261A (2)

Coro-Vane® Stationary Pump 521E Repair Kit CORKEN

Part Description

521E Stationary Pump Repair Kit No. 2904X2

Inlet Flange O-ring 2-234A Outlet Flange O-ring 2-234A R Valve Cap O-ring 2-224A RV Adj Screw O-ring 2-112A Cam/Liner* 1162-2 Rotor and Shaft* 11661X1R

Pump No. Seal Kit Brass Impeller C Model Motors Motor HP

C10 1003-0

F10 2556 1

C12 1003-2

F12

113CXAC13

1003-3 4261 2F13C14

1003-4 2557* 3F14

Part Models

Standard Optional Material Material

Case, Cover Ductile Iron ASTM A536

Impeller Copper Alloy ASTM B584, UNS C92300 Steel and

(Also Known as Navy Bronze) Stainless SteelImpeller Key Steel, Zinc PlatedSeal Seat All Silicon CarbideSeal Rotor CarbonSeal Metal Parts Stainless SteelSeal Sleeve AluminumSeal Housing Nickel-Aluminum-BronzeShaft Steel Stainless Steel

Frame FF/FD Gray Iron ASTM A48. Class 30

DLF/DLD DLF/DLD: Ductile Iron ASTM A536Bearing Cap Ductile Iron ASTM A536

O-rings Buna-N *Neoprene®, Viton®,

All Buna-N, Kalrez®

Retainer Rings SteelBearings Ball

Coro-Flo Pump Repair Parts - C and F Models CORKEN

*C model motors are single phase, except for the C14-2557-3HP

*Items not included in Kit, but may be ordered

* Neoprene® and Viton® are registered trademarks of the DuPont Company.

Pump Parts CORKEN

*Items not included in Kit

CORKEN PUMP REPAIR PARTS CORKEN PUMP REPAIR PARTS


133 134

GG

Item No. HP RPM Volts Frame

Full Load Weight Amps

EM7018T-1 1-1/2 3450 230/460 143T 2.1 42EM7042T-1 3 1725 230/460 182T 4.1 105EM7044T-1 5 1725 230/460 184T 6.7 120EM7072T-1 5 3450 230/460 184T 5.6 85EM7047T-1 7-1/2 1725 230/460 213T 10.2 177EM7170T-1 10 1725 230/460 215T 14.2 225EM7174T 10 3450 230/460 215T 11.6 236EM7054T-1 15 1770 230/460 254T 18 347EM7056T-1 20 1760 230/460 256T 24 365EM7058T-1 25 1775 230/460 284T 30.8 454

Item No. HP RPM Volts Frame

Full Load Weight Amps

VL5023A* 1 1725 115/230 56C 6.5 54VL5024A * 1-1/2 1725 115/230 56C 8 76L5030T 1-1/2 3450 115/230 143T 7.5 56L5018 3 1725 115/230 215 15 152L5028T 3 3450 115/230 184T 14.5 84L5020 5 1725 230 215 21 166

Item No.

In/Out Min/Max Register

Temperature Size Gal/Min Compensation

RL100108A12, 1” 3/4” FNPT 3 - 18 GPM 600 (AAAAD) NoRL100118A23 3/4” FNPT 3 - 18 GPM 600 (AAAAF) RL12521RGD1 1-1/4” FNPT 5 - 30 GPM RL15021RGD1 1-1/2” FNPT 12 - 60 GPM

833-0 Yes

RL20021RGD2 2” FNPT 20 - 100 GPM RL2002N21RGD2* 2” FNPT 20 - 100GPM


MA-7-GY-10 2” Meter with Mechanical Totalizer/Printer, TVC, 100 Mesh Strainer, L - RMA-7-GY-10-LCR2 2” Meter with LCR2, ETVC, 100 Mesh Strainer, L - R, ST221 SoftwareMA-7-GY-10-LCRP Same as Above with Preset

MA-7-GY-10-LCR2-EV 2” Meter with LCR2, ETVC, 100 Mesh Strainer, L - R, ST221 Software,

Electronic Vapor EliminatorMA-7-GY-10-LCRPV Same as Above with Preset


MA-5-CX-10 Standard Meter w/Air Eliminator, Strainer, Differential Valve, and CounterMA-5-CY-10 Same as MA-5-CX-10 Except: with Temperature Volume CompensatorMA-5-GX-10 Same as MA-5-CX-10 Except: with PrinterMA-5-GY-10 Same as MA-5-CX-10 Except: with Printer and Temperature Volume CompensatorMA-4-CX-10 Standard Meter w/Air Eliminator, Strainer Differential Valve and CounterMA-4-CY-10 Same as MA-4-CX-10 Except: with Temperature Volume CompensatorMA-4-GX-10 Same as MA-4-CX-10 Except: with PrinterMA-4-GY-10 Same as MA-4-CX-10 Except: with Printer and Temperature Volume Compensator

Three Phase Explosion Proof Motors BALDOR

Single Phase Explosion Proof Motors BALDOR

*C faced motors for Blackmer pumps

Liquid Meters NEPTUNE

*Ductile iron body, all others are aluminum

RL100108A12

METERS & REGISTERS

METER MA-7

The MA-7 Positive Displacement Meter is designed for LPG truck and bulk loading applications. Accessories may be rotated 180º or covers swapped to reverse direction of flow.

• 100 GPM (380 L/min.) capacity• Precision machined parts• Class 10 construction• Class 12 construction for NH3 (Anhydrous Ammonia) service is available upon request• Offers mounting flexibility

FEATURES: • Choice of 2” NPT standard, and 1-1/2”

optional companion flanges• Accessories: Vapor eliminator, strainer (100

or 200 mesh), screen, diaphragm valve• Mechanical or electronic registration• Optional temperature/volume compensation

Positive Displacement Meters MA 7 LIQUID CONTROLS

METER MA-5(MA-5-CX-10)

Positive Displacement Meters MA 5 and MA4 LIQUID CONTROLS

The MA-5 Positive Displacement Meter is designed for LPG truck and high speed motor fuel applications. Rate of flow 12 - 60 GPM (45-225 L/min.) capacity range.

The MA-4 Positive Displacement Meter is designed for LPG motor fuel applications. Rate of flow 5 - 30 GPM (20-1 15 L/min.) capacity range.

• Carbon insert bearings reduce friction and wear• Precision machined parts• Low pressure loss increases maximum

flow rate system• No planned obsolescence allows rebuild

rather than replace• Offers mounting flexibility

MA 5 AND MA4 METERS FEATURES: • For operation at any non-shock working

pressure up to 350 PSI• Choice of 1-1/2” NPT standard, and 2” optional companion flanges• Accessories may be rotated 180º• Covers may be swapped to reverse direction of flow

EM7174T

L5018

MOTORS METERS & REGISTERS


135 136

H

G

LectroCount TM Electronic Meter LIQUID CONTROLS

LectroCount is an electronic register that replaces the mechanical register, calibration gearsand/or adjuster mechanism traditionally used on many flow meters. It is designed to meet, even adapt to, your flow meter and process control instrumentation requirements.

• Weights and Measures (custody transfer) approved advanced microprocessor based electronic registration, presetting and

printing control systems• Accepts pulse input from most flow meters

FEATURES: • Rated NEMA-4 non-incentive Class 1,

Division 2, Group C and D• RS232.485 communications capable

LectroCount Meter

Electronic Registers E1000 and E4000 NEPTUNE

• Direct retrofit to RL100• Electronic calibration with K factor• Displays volume or flow rate in gallons,

liters, or barrels• Automatic reset• Programmable time-out between deliveries• Easy to read six digit display with up to three decimal places• Two year replaceable 3.6V lithium battery• Non-resettable totalizer• Operating temperature range -13 to 158° F• NEMA 4x enclosure

E1000 FEATURES:

Neptune’s Electronic Registers automate transaction operations for deliveries of LPG,commercially distributed liquids, and distillate fuels through flow meters on bulk delivery trucks.

• Compatible with automation technologies• Easy to use, menu driven display• Start with simple pump and print (imitate

your mechanical register)• Electronic temperature compensation

provides accurate, rapid response• Stand-alone pricing (print invoices directly

from the truck)• Configure register from laptop computer• Add data collection devices without the

need for additional register hardware• Interface with popular industry office software packages

E4000 FEATURES:

E1000

E4000

ProControl 2 Remote Readout BASE ENGINEERING INC.

The ProControl 2 Remote Readout is an all-in-one controller that greatly improves delivery efficiency and reduces costly fueling mistakes. Easily retrofitted to existing trucks or installed on new equipment, this patented system is ATEX certified for use throughout the world in hazardous locations.

A RFID option is available with the ProControl 2. RFID Option allows customer tank interlock, fleet refueling, ID capture, product manifold interlock and asset tracking.

• Handheld LCD display shows the exact meter reading to 1/10th of a unit in real time

• Direct serial interface with meter register shows a volume identical to the truck mounted register

• Exact programable delivery amount• Kits available for all types of electronic

and mechanical registers, including dual metered double pumper trucks

• Allow simultaneous control of up to eight custom truck operations

FEATURES: • Hose reel remote control• Tank valves can be opened with automatic

“delay” feature to engage PTO/Cargo Pumps

• Engine RPM can be remotely controlled to increase or decrease pump volume

• Emergency Stop feature closes all tank valves and stops truck engine

• Available with 5-minute ‘Query’ automatic emergency shut-down feature

NOTE: Emergency Stop requires manual system reset at truck. Internal valves and pumps cannot be reactivated with the handheld following e-stop. Pressing the e-stop button repeatedlysends the same shut-down signal. Driver can be safely moving away from the truck and be assured of shut-down.

ProControl 2 RemoteReadout with RFID

ASKW Series Remote BASE ENGINEERING INC.

ASKW Series LPG and Refined Fuels Remote Control Systems offer unrestricted hose end control greatly increasing productivity and improving safety over conventional truck mounted manual controls. ASKW Series are specifically for fuel delivery truck applications requiring explosion proof, severe-service remote controls. The system is available with one to eight control buttons in a rugged, compact package.

Emergency StopASKW Series

• Receiver units install easily• Prewired electrical harness supplied• External antenna/coax provides up to 1,000

ft. (300m) operating range• Powerful receiver picks up signal through

brick, concrete, and metal walls• Receivers are energized only during pumping operations

FEATURES: • Systems are factory ‘married’ with unique

32 bit ID codes ensuring the receiver will not work with any other transmitter

• Internal diagnostic LEDS monitor battery levels, signal connection, and wiring faults for easy troubleshooting

• Built-in ‘fail-safe’ feature closes all tank valves with any power loss or truck movement

Emergency Stop feature closes all tank valves, and kills the truck engine and pump. The ‘safetylatched’ signal causes the tank valves and pump to remain inoperative until a manual system reset is performed. Pressing the E-Stop button repeatedly will send the same shut-down signal. This system meets International regulatory requirements and is available for all types of pneumatic, cable operated or Flowmatic type tank valves and all truck engines.

METERS & REGISTERS PLANT & VEHICLE REMOTE CONTROLS


137 138

H H

ASKW Series Remote Controls (continued) BASE ENGINEERING INC.

The ASKW Series Query Option is required on LPG delivery vehicles in some countries and isavailable on all ASKW systems. This feature requires the operator to periodically press a ‘QUERY’button on the remote control to keep the pumping system active. If the operator fails to pressthe QUERY button within a factory specified time an audible warning is first sounded followedby activation of the trucks EMERGENCY STOP system. The operator can press the ‘QUERY’ button at any time during the delivery or audible warning period and reset the timer.

The ASKW Series Engine RPM or Throttle Option allows the operator to increase/decrease truckengine RPM and correspond pump volume from the customers tank/hose-end of the delivery.Operator can begin delivery process, ensure product is flowing safely, then increase pump speed until tank is nearly full. Connections are available for any electronic or mechanical enginecontrol system.

The PTO(s) or Pump Option for the ASKW Series Remote extends pump life and increases safetyby allowing the operator to engage and disengage the PTO and pump from hose end at the storage tank. Truck PTO shaft is not turning, pump is not running in by-pass, and hose is not charged unless connected to the tank. PTO connection can be electric, pneumatic, “hot shift” or “clutch shift”. Remote PTO Delay option automatically opens tank internal valve 5 seconds prior to engaging PTO, allowing pump and product lines to equalize pressure. This feature prevents an excess flow ‘slug’ situation which when happens, starves the pump of product, and may lead to pump failure.

The Hose Reel Option for the ASKW Series Remote remotely unwinds and/or rewinds the hoseon or off the reel. Easy to install prewired hose reel motor solenoids and 70 amp breaker is included with this option. System design prevents Unwind and Rewind circuits from being energized at the same time.

ASKW Series Remote Enable Option can be specified to create a ‘two step’ process foractivating certain buttons to further prevent unintended button operation.

The Turn-Key ‘Plug & Play’ System is available with pre-wired pneumatic solenoids, relays, electric solenoids, and actuators. This system simplifies conversion of existing manual truck controls or up-fit new chassis and tanks. Modular components allow for easy installation and field replacement. Air solenoids are extremely rugged and can be direct mounted to chassis allowing hose-end PTO, tank valve, and cargo pump interlock.

Query Remote ControlASKW Series

Enable Remote ControlASKW Series

Turn-Key Remote ControlASKW Series

Engine RPM Remote ControlASKW Series

PTO Remote ControlASKW Series

Hose Reel Remote ControlASKW Series

PLANT & VEHICLE REMOTE CONTROLSE-Stop Bulk Plant System BASE ENGINEERING INC.

The E-Stop Bulk Plant Wireless Emergency Shutdown System eliminates costly hard wiring offixed location emergency stop switches. Any number of wireless remote E-Stop switches can be installed within the plant facility and communicate with one receiver/controller unit. These systems will work in conjunction with existing, hard-wired, manual E-Stop switches and plant safety controls. Operator worn E-Stop remotes can also be added to these systems.

NOTE: Daily E-Stop transmitter battery tests and scheduled battery replacement interval is strongly recommended. The E-Stop transmitters and receiver/controller shut-down will NOT operate when the remote E-Stop transmitter batteries are exhausted.

DSSF 100-AC System is a direct sequence, spread-spectrum remote E-Stop switch that operatesat 2.4GHz using a rechargeable battery pack. The E-Stop switch and receiver/controller unit areconnected via SafeLink, a continuous monitoring feature exclusive to BASE Engineering. Any loss of signal connection between the remote E-Stop switch and receiver/controller results inan automatic E-Stop trigger until the signal is restored. High powered E-Stop transmitters havean operating range of up to two miles. Transmitters must be connected to a back-up power supply as the battery pack will operate for only seven days. Back up power can be 12/24VDC, 120/240VAC, and solar powered where practical.

• Frequency of Operation: 433.92mHz• Method of Transmission: 56 bit DES encryption key• Rugged weatherproof polymer enclosure• External rubber flex antenna• 1,000 ft. (300m) operating range

FEATURES AND SPECIFICATIONS: • Up to 2 miles high powered signal option• Operational in –20º F to 185º F• Operates on common ‘AA’ batteries• 300 hours battery life with continuous use• Intrinsically safe for use in hazardous environments

ASKM100-AC E-Stop Remote has a fixed-frequency switch that operates at 433mHz using twodouble “A” batteries. The transmitter is energized only when E-Stop switch is activated. Batterytest button shows a “low battery” flashing LEd on the E-Stop switch as well as on the receiver/controller unit.

• Frequency of Operation: 2.4GHz DSS (869.7 and 902-928mHz available)

• Method of Transmission: 56 bit DES encryption key• Rugged weatherproof polymer enclosure• External rubber flex antenna

FEATURES AND SPECIFICATIONS: • 1,000 ft. (300m) operating range• Up to 2 miles high powered signal option• Operates on rechargeable lithium ion batteries (included with 12/24VDC charger)• Operational in –20º F to 185º F• 30 hours battery life with continuous use

Modular Din RailComponents

PLANT & VEHICLE REMOTE CONTROLS


139 140

H H

E-Stop Bulk Plant System (continued) BASE ENGINEERING INC.

• Operates with 12/24VDC or 120/240VAC power supplies

• Receiver/controller outputs can be specified as 12/24VdC, 120/240VAC, dry contact,

RS232, or J1939 CAN bus• Constructed of IP67 rated, impact resistant

polycarbonate

FEATURES AND SPECIFICATIONS: • External antenna/coax included• Pre-wired to meet customer requirements• Serial Communication: Optional J1939

CAN bus/RS232 interface to OEM serial networks

• Electric/pneumatic solenoids are available upon request

E-Stop Transmitter is a low powered, intrinsically safe device suitable for use in Zone 2, Class 1, Div 2, Group “D” hazardous environments. Pressing the Emergency Stop button causes the receiver/controller unit to trigger a plant shut-down. The system cannot be rebooted until the E-Stop button is pulled out and a manual receiver/controller reset is performed. E-Stop buttons are dual contact, dual channel, and comply with global E-Stop switch requirements. Systems will fail safe, triggering an automatic E-Stop with any loss of main line electrical power supply to the receiver/controller unit. All systems are CSA, CE, and FCC approved.

E-Stop Receiver/Controller easily interface with electrical, pneumatic, nitrogen, or mechanical plant shut-off equipment.

NOTE: Standard receiver/controller units are NOT rated explosion proof and are typically installedin non-hazardous electrical control equipment areas. Receiver/controller units are provided withantenna and coax cable for outside antenna mounting providing maximum operating range. Explosion-proof electrical enclosures are available on request.

Standard Wall MountE-Stop Switch

Optional HandheldE-Stop Available for

any System

Wireless Deadman Series Remote Control BASE ENGINEERING INC.

The Deadman Series Trigger Switch Remote Control is specifically for industrial applications requiring positive operator-to-machine contact. A wireless trigger-switch is used to send RF command signals to the pump. The operator is unencumbered by cables and wires normally usedin ‘deadman’ fueling operations. The Deadman Series incorporates a secure frequency hopping,spread-spectrum radio link that is virtually immune to outside electrical or RF interference. Operations fail safe (shutdown) with any loss of signal from transmitter.

Deadman Transmitters are available with Hose Reel, PTO (pump), Engine RPM (throttle), Emergency Stop, and Enable options.

• Frequency of Operation: 902-928mHz FHSS (433.92mHz, 869.7mHz and 2.4GHz radios available)

• Transmitter Power: 100mW• Method of Transmission: 56 bit DES encryption key• Rugged weatherproof polymer enclosure• Internal antenna ‘on card’ PCB mount• Operational in –20º F to 185º F

TRANSMITTER FEATURES AND SPECIFICATIONS: • Up to 500 feet operating range (higher

power available)• Operates on common ‘AA’ batteries• 30 hours battery life with continuous use

with audible low battery warning and flashing LED indicator• Rechargeable lithium ion cell with

12/24VDC charger• Intrinsically safe for hazardous environments

Deadman Trigger SwitchRadio Tansmitter


• Power supply: 12/24VDC (Optional 120VAC systems available)

• Current load is up to 4 amps per channel or 10 amps total

• Constructed of impact resistant polycarbonate, IP67 rated• Rugged weatherproof polymer enclosure

RECEIVER FEATURES AND SPECIFICATIONS: • Internally protected and encased antenna

(external antenna/coax available)• Pre-wired to OEM requirements, quick connect fittings supplied• Up to12 programmable channels• Optional CAN bus interface is available

Wireless Deadman Series Remote Control (continued) BASE ENGINEERING INC.

Crane and Service Truck Radio Remote Control BASE ENGINEERING INC.

Crane and Service Truck Radio Remote Controls greatly increase jobsite safety by providing the operator the safest vantage point for tank delivery. One-man control eliminates a second personinstructing the operator where to position the tank. Operator has freedom of movement aroundentire worksite while setting tank precisely into position.

ASKR Model was developed for Crane and Service truck applications.

FHSR Model is designed for crane applications requiring interference-free, fail-safe machine control. Operator handheld and machine mounted transceiver continuously communicates toensure signal validity and strength. Any loss of signal results in all active functions automaticallyshutting down and failing safe. The FHSR system incorporates a secure frequency hopping, spread-spectrum radio link that greatly reduces outside electrical or RF interference.

DSST Model is designed for proportional hydraulic crane applications requiring up to twelve radio remote control functions. Toggle switch controls with trigger provides variable speed control of hydraulic pump solenoids. Split signal capability allows combined boom movementsincluding ‘up and sideways’ and ‘extend and winch down’. Weatherproof receiver can be cranemounted and interfaces easily to crane electrical system with OEm style plug-in connector.

ASKW Model allows up to 8 control functions. Two ‘AA’ batteries provide 300 hours of continuoususe. Parts replacement is simplified with quick connect plugs and simple ‘learn’ button to link handheld and receiver. Transmitter has low battery warning indicator and button text is printed to customer specifications at time of order.

• Handheld transmitters are available with up to twelve crane control buttons

• Rechargeable lithium ion cell with 12/24VDC charger

TRANSMITTER FEATURES AND SPECIFICATIONS: • Specifications are similar to the Deadman

Series Remote Control Transmitter

• Up to twelve pre-programmed high-side outputs available

• Outputs can be selectively interlocked to other operations for safety reasons

• Modular components allow for easy installation and field replacement

RECEIVER FEATURES AND SPECIFICATIONS: • Interface to OEM crane controls can be

simplified with factory installed, direct-plug connectors or through J1939 serial communication (other protocols available)• Specifications are similar to the Deadman

Series Romote Control Receiver

ASKR Model

ASKW Model

Mounted Receiver/Controller

DSST Model



141 142

H H

Passive Transport Leak Detection System BASE ENGINEERING INC.

Passive Transport Leak Detection Systems are designed for propane, anhydrous ammonia andbutane transports. These systems continually monitor the off-loading process looking for a rapidchange in discharge pressure. They detect a separated hose or failed connection and close the tank internal valve within half a second.

• Easy to install• No calibration or adjustment• Options include multi-pipe or multitrailer

sensors, automatic truck engine or PTO shut-down

FEATURES AND SPECIFICATIONS: • Test button determines a unit’s readiness• DCE certified to comply with all US DOT

and Canadian Transport Canada regulations for ‘Passive Shut Off’

• Power source: 12 volts DC

Model LDS 60 is a fully automatic leak detection system for propane and anhydrous ammonia transports. The low powered intrinsically safe control unit continually monitors piping and hoseassemblies during the off-loading process. A failed pipe, or hose separation will cause the tank’sinternal valve to close instantly and sound an audible air-horn alarm. A simple “reset” button returns the unit to the monitoring state.

Model LDS 100 is an automatic leak detection and shut down system designed specifically for LPG and Anhydrous Ammonia bulk transfer. Intrinsically safe unit continually monitors theoff-loading process for “rate of change” parameters signifying broken or damaged hoses, fittingsand piping. A leak is instantly detected and stopped by the closure of the tank internal valve(s). The truck’s engine can also be stopped and PTO disengaged if desired. This system automaticallyactivates at the end of each load. This ensures that the system is fully operational and helps reduce the possibility of a damaged cargo pump due to product run out. This unit also “fails safe” and closes the internal valve with a loss of power or the release of the trailer parking brakes.

Model LDS 200AQRF is designed to comply with DOT requirements for transports with both ‘metered’ and ‘bulk’ discharge capability. Combines all of the features described above for the LDS100 but includes a handheld with remote control ‘Query’ and ‘Emergency Stop’ buttons. An audible alarm sounds every 4:30 seconds giving the operator 30 seconds to respond by pushing the ‘Query’ button. Failure to push the ‘Query’ button results in automatic activation of the passive shut-down system. Pushing the ‘Query’ button refills the timer to allow 5 more minutes of offloading. Additionally, the remote ‘E-Stop’ button gives the operator the ability to activate the passive shut down at any time during the offloading process.

LDS 60

LDS 100

LDS 200AQRF

Driver Authorization System BASE ENGINEERING INC.

Driver Authorization Systems are designed specifically for commercial vehicles and machinery.The system protects the vehicle from unauthorized engine start or movement depending on the customer’s application.

• Keypad unit with hidden enclosure screws• Sealed parking brake low pressure switch

with DOT quick connect T fitting• Sealed engine kill relay sensors, automatic

truck engine or PTO shut-down• Air line fittings supplied

FEATURES: • Components are pre-wired with quick connect electrical. Trucks with existing parking brake air pressure switches and engine kill relays, (radio shut down

systems) may be able to use some of these components. Contact BASE Engineering at

800.924.1010 to confirm.

PLANT & VEHICLE REMOTE CONTROLSDriver Authorization System (continued) BASE ENGINEERING INC.

Model DAS1000IGN prevents unauthorized engine start. System is armed automatically each time the key is turned off. Entry of correct user code disarms system and allows engine to be started. Used on all types of vehicles and equipment.

Model DAS1000AT prevents unauthorized vehicle movement on vehicles with automatictransmissions. System arms automatically when shifting transmission into park. Shifting the vehicle into drive without entering a valid user ID causes engine to stall. Entry of correct code disarms system and allows engine start. Well suited for any vehicle that needs to be leftunattended with engine running.

Model DAS1000AB operates the same as Model DAS1000AT with the addition of being armedwith the application of the truck’s parking brake. This system requires the vehicle to be equippedwith air brakes. Releasing the parking brake without entering a valid ID code will cause the engine to stall. Entering a valid ID code disarms the system and allows engine start. Wellsuited for large trucks with air brakes and engines that need to be left running while the vehicleis unattended.

Model DAS1000ABT is similar to Model DAS1000AB, but designed for tractor trailer units witha dedicated trailer parking brake. System is armed with application of tractor or trailer parkingbrake. Prevents deliberate bypass of authorization system by drivers using trailer brakes versestractor brakes to park vehicle (see above). Attempting to bypass, disable, or damage any BASEDriver Authorization System will cause the ignition to lock out until repairs are made and a validcode entered.

Auxiliary Fuse Panel BASE ENGINEERING INC.

Auxiliary Fuse Panels are designed for new or existing truck chassis requiring additional fusedconnections. Ideal for adding radio controls, work lights, GPS systems, electronic meters to truck electrical system.

• Adds (6) additional 10 amp fuse connections under dash or on firewall• IP67 rated enclosure is sealed against

weather and pressure washers

FEATURES AND SPECIFICATIONS: • Includes: - built-in isolation relays for ‘keyed and

fused’ power supply

- battery connection cables and wire harness for six fused input/outputs

- all required wire connections



143 144

H H

Ref Part Part Name


1 9945.1001 Roller Body Casting w/Mounting Bolts* 1 2 9945.1002 Guide Arm Casting* 1 3 9945.0009 Mounting Yoke with Bronze Bushings 1 4 9917.0207 Switch Mounting Bracket* 1 5 9917.0200 EPS-1 Explosion-Proof Switch 1 6 9945.1003 Guidemaster Pinlock Assembly, S/S* 1

7 9945.0024 SST Pivot Pin (with 1/4” Cap Screw and

1 Lock Washer)

8 9945.0019 GM-609 Roller (with 2 Pressed-in

2 Ball Bearings) 9 9945.0026 GM-608 Ball Bearing 4 10 9945.1004 Guidemaster Bottom Roller Plate* 1 11 9954.0030 1/2” Lock Washer 2 12 9954.0036 1/2”- 13 Hex Nut 2

Ref Part Part Name


13 9945.0015 1/4”- 20 x 3/4” Socket Head Cap Screw 4 14 9945.0013 5/16”- 24 x 2-1/2” Plated Bolt with Nut 2 15 9945.0027 5/16”- 24 Hex Nut 2 16 9945.0011 Oil-impregnated Bronze Bushing for Yoke 2 17 9945.0015

1/4”- 20 x 3/4” SST Socket Head 4

Cap Screw 18 9954.0008 1/2” Flat Washer 2 19 9945.1005 Roller Mounting Bolt (Threaded)* 2 20 9945.0055

1/4”- 20 x 5/8” SST Socket Head Cap 2

Screw and Lock Washer 21 9958.0010 1/4”- 20 X 5/16” Set Screw 1 22 9954.0004 5/8” Flat Washer 6 23 9904-9201 3/8”- 16 x 3/4” Button Socket Head 4 24 9904.5290 3/8”- 16 Hex Acorn Nut 4

COMPONENTS

1 Bearings - Weight of spool and hose is supported by bearings.

1a Back Bearing

1b Front Bearing

2 Disc - Rolled edges prevent hose damage and add rigidity to disc. Additional strength is

provided by a concentric rib.

3 Drum - Roll formed steel with full-length weld.

4 Tie Rods - Join discs and drum to form spool. Reinforced with pipe spacers for rigidity and strength.

5 Chain and Sprocket Drive - Provides smooth positive rewinding on powered reels.

6 Rewind Motor - Electric rewind motor is shown. Compressed air or hydraulic motors can be used.

6a Electric Junction Box

7 Hub assembly - Includes the fluid hub, the outlet riser, and the reel axle. Fluid passes from the swivel joint inlet through the hub assembly, to the hose.

7a Outlet riser - Contoured to match the curve of the reel drum so hose will wrap smoothly.

7b Fluid hub

8 Swivel joint inlet - Permits reel to rotate freely while connected to the fluid source. Joint is

not used as a bearing. Straight or 90° swivel joints are available for most models. (Flexible connector must be used between swivel joint and inlet piping or warranty will be void.)

9 Brake/rewind assembly - Bevel gear rewind has an adjustable tension brake. Rewind and braking devices vary with different models.

10 Front Frame

11 Back Frame

12 Front Foot

13 Back Foot

CONSTRUCTIONFrames, discs, and drum are fabricated of heavy-gauge steel. Bearings are self-aligning. Malleable iron and steel are used for hose reel hub assembly, outlet riser, and swivel joints. Stainless steel, aluminum, and special swivel joint packing can be supplied to meet special requirements.

FINISHStandard finish is oven-cured enamel. Finishes other than standard, such as special primers, may be specified at extra cost.

TEMPERATURES AND PRESSURESStandard reel construction will handle most liquids or gases at temperaturesranging from -20° to +400° F (-29° to +204° C). Operating pressures availableup to 10,000 PSI (690 bar) depending on the specific reel series. These operating pressures and temperatures are shown on descriptive pages ineach product catalog. Reels to operate at pressures and temperatures otherthan standard are available at extra cost.

SHIPPINGReels are shipped completely assembled, ready to install. Installation instructions are supplied with each reel.

REELSPump Parts List BLACKMERHose Reel Anatomy HANNAY

This cutaway illustration shows a typical power rewind reel with an optional auxiliary crank rewind mechanism. All Hannay reels are assembled from combinations of the basic components shown here. Since components are taken from a large inventory,each reel is assembled to the buyer’s particular requirements. This cutaway illustrationshows a typical power rewind reel with an optional auxiliary crank rewind mechanism.All Hannay reels are assembled from combinations of the basic components shown here. Since components are taken from a large inventory, each reel is assembled to thebuyer’s particular requirements.

ORDERING INFORMATION

Be sure to specify complete model number, serial number of reel, and part number.

REELSPump Parts List BLACKMERGuidemaster Parts List (model GM-700) HANNAY


145 146

H H Item No. Material Description

MEP-GMC1 Black EPDM Hose Reel Control Switch Cover for Guidemaster® Control Arm MEP-RDC1 Black EPDM Hose Reel Control Switch Cover for Red DOT EPS


PB800 Handles 3/4” or 1” I.D. Hose, Standard Pressures to 2,000 PSI, Available Up to 6,000 PSI


PB Series Manual or Power Rewind, 1” to 1-1/2” I.D. Hose, Standard Pressures to 350 PSI (24 Bar)


PBGMB Handles 1” to 1-1/2” I.D. Hose, Standard Pressures to 350 PSI (24 Bar)

REELS

• Non sparking ratchet locks reel• Declutching arbor prevents rewind damage• Available with channel frames for heavy-duty applications• 90° ball bearing swivel joint inlet with

1-1/2” female NPT threads

FEATURES: • Performs in temperatures from -40° F to

+350° F• Standard outlet is a flanged riser with 1” female NPT threads• Narrow version available upon request

Series PB800

Hose Reel Control Switch Covers MARSHALL EXCELSIOR

MEP-GMC1

MEP-RDC1

• Made with durable UV stable black low temperature EPDM material

• Includes security lanyard to help prevent loss of the cap

FEATURES: • Control switch can be operated through

cover without removing

Hose Reel Control Switch Covers are intended to protect Hannay® Hose Reel Control Switchesfrom moisture and/or other contaminants during over-the-road transit. The MEP-GMC1 isspecifically designed to fit Hannay® Guidemaster® control switches while the MEP-RDC1 fits Hannay® red DOT EPS style control switches.

Spring Rewind Reel Series PB800 HANNAYReel Series PB/DPB HANNAY

REELS

Series PB are explosion-proof reels that are used individually or in pairs for liquid and vapor return hoses. These reels are available in a gear-driven crank rewind, #40 chain and sprocket drive powered by an electric, hydraulic or compressed air motor, or direct drive hydraulic rewindmotor. Crank rewind and direct drive reels are supplied with pinion brakes. Power rewind reels(chain and sprocket driven) are supplied with a strap brake. Other sizes and/or threads can be furnished and must be specified when ordering as well as the roller position.

Series PBElectric Rewind

Series PBGMT with Bottom-Mounted Guidemaster are ideal for open-deck or compartment mounting. Reels are available with #40 chain and sprocket drive powered by an electric, hydraulicor compressed air motor, or direct drive hydraulic rewind motor. Direct drive hydraulic rewind reels are supplied with pinion brakes. Electric powered rewind reels are supplied with a strap brake. Other sizes and/or threads can be furnished and must be specified when ordering as well as the roller position.

Series PBGMBElectric Rewind

• 90° ball bearing swivel joint inlet with 1-1/2” female NPT threads

• Handles pressures to 350 PSI (24 bar)• Performs in temperatures -40° F to +350° F• Steel inlet, outlet riser, and hub assembly

FEATURES: • Standard outlet is a flanged riser with 1”

female NPT threads• Accessory items include rollers and roller

mounting brackets• Alternate brake and locking devices available

• 90° ball bearing swivel joint inlet with 1-1/2” female NPT threads

• Standard outlet is a flanged riser with 1” female NPT threads

FEATURES: • Performs in temperatures -40° F to +350° F• Alternate brake and locking devices available• Top-mounted guidemaster available

Reel Series PBGMT with Bottom-Mounted Guidemaster HANNAY


147 148

H H Item No. Hose I.D. Hose O.D. # of Braids Ft/Reel *

7132-25354 1/4” .58” 350’/700’ 7132-38354 3/8” .75” 600’ 7132-50354 1/2” .94”

2 500’

7132-75354 3/4” 1.25” 350’ 7132-10054 1” 1.50” 250’ 7132-1252 1-1/4” 1.87” 150’ 7232-1503 1-1/2” 2.18”

3 150’

7232-2603 2” 2.75” 100’

Item No. Hose Size Hose End

7661-04MP04TY 1/4” I.D. 1/4” MNPT 7661-04FJ04TY 1/4” I.D. 1/4” Female Flare S101HY-6-6 3/8” I.D. 3/8” MNPT S108HY-6-6 3/8” I.D. 3/8” Female Flare 7661-08MP08TY 1/2” I.D. 1/2” MPT 7661-08FJ08TY 1/2” I.D. 1/2” Female Flare S101HY-12-12 3/4” I.D. 3/4” MNPT 7661-16MP16LAR 1” I.D. 1” MNPT S101HY-20-20 1-1/4” I.D. 1-1/4” MNPT S10143-24-24 1-1/2” I.D. 1-1/2” MNPT 7661-32NP32LA 2” I.D. 2” MNPT

Item No. Inside Diameter Working PSI Burst PSI

R50012320000 1-1/2” R50016330000 2”

150 600R50024320000 3”R50032320000 4”

HOSES & ACCESSORIES1” Bobtail Hose

Series 7132

Propane Hose

The LP Gas Hose 7132 Series is heavy duty, flexible, and designed for liquid or vapor transfer. The 7132 Series has a black neoprene cover, continuous labeling, and has a maximumrecommended working pressure of 350 PSIG. UL Listed Hose is available in cut lengths by the foot, or in reel lengths. Order by inside diameter.

Series 7232

* Estimated - some reels may be different lengths

Crimped On Hose Ends

Crimped On Hose End

HOSES & ACCESSORIESSmart-Hose Transfer Assemblies

Smart-Hose Assemblies are designed and engineered with a valve integrated in each end fitting. If the hose assembly experiences a catastrophic hose failure, the Smart-Hose Safety System is designed to instantaneously shut off the flow in both directions. Designed as a passive safety device, the Smart-Hose Safety System needs no human intervention to activate.

The Smart-Hose Safety System is integrated into Petroleum transfer hose assemblies and are designed for use in tank truck and in-plant operations to transfer gasoline, oil, ethanol blends and other petroleum base products up to 50% aromatic content. It is designed for pressure, gravity flow, or full-suction service.

• Hose cover is synthetic rubber (oil resistant), has a smooth cover with wrapped finish• Hose is reinforced - spiral-plied synthetic

fabric with wire helix• Hose tube is made with Nitrile synthetic

rubber RMA Class A (high oil resistant) • Hose is efficient in temperatures from

-35°F to 200°F

FEATURES: • Each hose is tested under water with dry

air or nitrogen to working and test pressure• Each hose is serial numbered• Shipped with a test certificate and operating booklet

Smart Hose

Smart HoseCut-away Views

Smart Hose Cut-awaySide Views

Item No. Length Description Min Bust PSI

20523 100’ Cold Weather Flex 1,7501” Bobtail Delivery Hose,Factory Crimped Ends,

Tested and Certified

24046 125’ Cold Weather Flex 1,75024047 150’ Cold Weather Flex 1,7507132XTCLAR16MP-1500 125’ Flex Low Temp —7132XTCLAR16MP-1800 150’ Flex Low Temp —


149 150

HH

Hose Size Coupling Length Min. Overall Length

1/2” ID 2-7/8” 9”

3/4” ID 3” 1” ID 3-1/2” 10” 1-1/4” ID 4” 1-1/2” ID 4” 12” 2” ID 5-1/2”

Item No. Pipe Size Overall Length No. of Steel Braids

630002 1/2” MNPT 12” 630006 12”

Single630008 3/4” MNPT 16” 630010 18” 630026 1” MNPT 630056 1-1/4” MNPT 16” 630096 1-1/2” MNPT Double630136 2” MNPT 18” 630171 3” MNPT 22”

NOTE: Never use a flexline to correct bad plumbing. Flexline must be kept straight. Do not use on mobile installations - use high pressure Parker rubber hose, with pressed on ends, certified.

Stainless Steel Flex Connectors

• Braided stainless steel for liquid propane service

• 350 PSI rated• Prevents piping damage from vibration and

thermal expansion

FEATURES: • Schedule 80 ends• Custom made flexlines to your specifications• The length shown in the chart is the minimum. Maximum length is 36”.

FLEX CONNECTORS

ME3162-32B ME3162-32S

ME3162-20

Marshall’s Clamp Style Hose Couplings are user friendly and easy to install in the field. A steel or ductile hose barb is inserted into the hose and two outer clamps, positioned on the outside of the hose, have a boss to keep the bolts from rotating while the clamps compress the hose for a leak free seal.

NOTE: Clamps must be installed with clamp lip fully engaged into flange groove on hose barb body.

• Hose barbs are constructed of zinc plated steel or ductile iron with automotive grade powder coat finish

• Hose clamps are ductile iron with automotive grade powder coat finish

FEATURES:

HOSES & ACCESSORIES

Rubber Flex Connectors are custom made and certified rubber flex connectors. Maximum length available is 36”.

Rubber Flex Connectors

• Optional integrated female Acme swivel eliminates weight of additional couplings

• Includes hose barb, two clamps, nuts and bolts

* Rated for LP-Gas

Clamp Style Hose Couplings MARSHALL EXCELSIOR

Item No. Hose Barb Outlet MNPT

ME3162-08 1/2” 1/2”ME3162-12 3/4” 3/4”ME3162-12S 3/4” 1-3/4” F. Acme SteelME3162-1216 3/4” 1”ME3162-16 1” 1”ME3162-16S 1” 1-3/4” F. Acme SteelME3162-1612 1” 1-1/4”ME3162-2016 1-1/4” 1”ME3162-20 1-1/4” 1-1/4”ME3162-2018S 1-1/4” 1-3/4” F. Acme SteelME3162-2020S 1-1/4” 2-1/4” F. Acme SteelME3162-24 1-1/2” 1-1/2”ME3162-24S 1-1/2” 2-1/4” F. Acme SteelME3162-32 2” 2”ME3162-32B* 2” 3-1/4” F. Acme BrassME3162-32S 2” 3-1/4” F. Acme Steel


Item No. Description F. Acme MNPT LPG NH3

ME135 Brass Nut/Steel Stem and S.S. Hose Assembly 3-1/4” 2” Yes NoME135S Steel Nut/Steel Stem and S.S. Hose Assembly 3-1/4” 2” Yes Yes

151 152

H H

Accessories

Item No. Inlet Outlet Factory Discharge

Mechanical Brake Electronic Back Check (M. Acme)

(MNPT) Installed at

Material Interlock Proximity Test

Screen Disconnect Retro-Fit Interlock Kit Adapter

ME866-8 1-3/4” 1” No .16 CC Brass — — —ME866A-8 1-3/4” 1” Yes .16 CC Brass — — —ME866-10 1-3/4” 1-1/4” No .16 CC Brass — — —ME866A-10 1-3/4” 1-1/4” Yes .16 CC Brass — — —ME867-10 2-1/4” 1-1/4” No 1.96 CC Brass — — —ME867A-10 2-1/4” 1-1/4” Yes 1.96 CC Brass — — —ME868-16* 3-1/4” 2” No 3.11 CC BrassME868A-16* 3-1/4” 2” Yes 3.11 CC Brass

ME868MIB ME868PIB MEP105ME868-24* 3-1/4” 3” No 3.11 CC BrassME868A-24* 3-1/4” 3” Yes 3.11 CC Brass

ME807-16

3 1/4” F. Acme x 2” MNPT Filler Coupling MARSHALL EXCELSIOR

The Turbo-Flo LE™ (Low Emission) Transfer System is the industry’s most efficient and cost-effective way to transfer LP-Gas in bobtail, transport, railcar, and bulk plant applications. This product will pay for itself through gas savings during disconnect and its increased flow rate. While any part of this system is interchangeable with other standard systems, to receive maximum savings, all three products (LE Transfer Valve, LE Acme Adapter, and MEC Globe Valve) must be used simultaneously.

The ME807 Turbo-Flo LE™ Shut-Off Valve is designed for use with LPG and LH3 Tranfer Systems.This system provides a safe, ergonomic and efficient solution to transfer applications while increasing productivity. For use with bobtail, transport, railcar and bulk plant applications.

The ME808-16 Series Valves feature our new modular Excela-Flange 4-bolt inlet flange design that can be easily adapted to both NTP thread or socket weld type A companion flanges (ME840and ME841 Series) ranging from 1-1/4” to 2” in diameter making it universal to piping sizes within this range. This innovative system allows installers the ability to eliminate unnecessary connections as well as possible leak points by integrating a convenient 4 bolt flange union at the valve inlet. The Turbo-Flo LE system provides a safe, ergonomic and efficient solution for liquid or vapor transfer applications while increasing productivity and dramatically reducing fugitive product emissions. For use with bobtail, transport, railcar and bulk plant applications.

ME135

TURBO-FLO LE DRY BREAK TRANSFER SYSTEMTurbo-Flo LE™ Dry Break Transfer Valves MARSHALL EXCELSIOR

The ME135 Discharge Hose Adapter allows transport hoses to be adapted to work with the ME807 LE Shutoff Valve while providing a flexible connection in the transport trailer hose bleeddown lines. It is intended to be used with ME807-16 in applications where ME806-16 Turbo-FloLE Valve is not practical due to space or lack of fixed loading or unloading lines. The ME135 allows for normal use of on board passive shutdown hoses and traditional product “blow down”discharge lines in instances where LE hose end valves are not practical. Acme connection comes fully assembled with an stainless steel hose, fittings, self-closing ball valve and quick disconnect for easy installation.

NOTE: Quick Disconnect is 3/8” FNPT

Item No. Description Discharge atDisconnect Material

ME806-16 Low Emission Transfer Valve2” FNPT x 3-1/4” F. Acme Swivel

.09CC

Ductile/Brass

ME806S-16 Ductile/Steel

ME807-16 Low Emission Transfer Valve2” FNPT x 3-1/4” M. Acme Swivel

Ductile/Brass

ME807S-16 Ductile/Steel

ME808-16 Low Emission Transfer Valve 4 Bolt Type BFlange x 3-1/4” M. Acme Fixed

3.2 CC

Ductile/Brass

ME808A-16 Low Emission Transfer Valve 4 Bolt Type BFlange x 3-1/4” M. Acme Fixed - w/screen Ductile/Brass

ME808S-16 Low Emission Transfer Valve 4 Bolt Type BFlange x 3-1/4” M. Acme Fixed Ductile/Steel

ME808SA-16 Low Emission Transfer Valve 4 Bolt Type BFlange x 3-1/4” M. Acme Fixed - w/screen Ductile/Steel

ME806-16

ME808-16

TURBO-FLO LE DRY BREAK TRANSFER SYSTEMTurbo-Flo LE Acme Adapters MARSHALL EXCELSIOR

* Not for use in conjunction with soft seat back check | To determine payback and cost savings visit www.marshallexcelsior.com

ME868BLK Bypass Line Kit creates a one-way closed loop between the up and down stream sides of a Marshall Excelsior 2” globe valve when used in conjunction with a ME868 Series lowemission Acme adapter. The Bypass Line Kit features a brass one-way check valve and heavy wall copper tubing with brazed end fittings for durability. The kit prevents over pressurizationof the ME868 Series low emission Acme adapters and greatly reduces pressure within the ME868 Series adapters which decreases wear that may occur to the shutoff valves or the lowemission Acme adapter.

ME868MIB Mechanical Interlock Bracket allows for a standard Parker style pneumatic air roller valve, typically used with standard bobtail brake interlock systems, to be retro-fit to the ME868 Series low emission Acme adapters. This bracket system moves the standard brake interlock system and connections forward to the end of the low emission adapter thus allowingnormal contact with the ME441F8 flange Acme cap. All bracketing and mounting hardware are included in the kit however, the Parker style pneumatic roller valve is not included.

ME868-16 and ME825IBC-16 are to be used with LPG and LH3 Tranfer Systems. This system provides a safe, ergonomic and efficient solution for transfer applications while increasingproductivity and dramatically reducing fugitive product emissions. For use with bobtail, transport, railcar and bulk plant applications.


ME868BLK

TURBO-FLO LE DRY BREAK TRANSFER SYSTEM FEATURES: • Reduces product emissions over 99.6% • 100% compatible with all existing acme

transfer connections• Safety latch prevents accidental valve opening• Cam operated vapor equalization feature for

smooth valve operation• All stainless internal components• Factory installed hydrostatic relief valve• Low temperature valve seals for maximum

performance under all operating conditions• Hardend steel bearing race with stainless

steel ball bearings (ME806 Series Only)

• Integrated Back Check (IBC) feature allows trapped liquid to be forced back upstream of the valve if liquid is trapped downstream of the valve seat (ME807 Series Only)

• Brass or steel acme connections (ME806 and ME807 Series)

• Designed for bi-directional flow of product• Integrated pilot feature allows the ME807 to

equalize and open only when connected to ensuring maximum safety

• Bi-directional flow of product (ME806 and ME807 Series)

ME868-16/ME825IBC-16


153 154

H H

The ME868PIB Proximity Interlock Bracket uses the new MEC Smart Interlock Technology which connects with the Allison automatic transmission Auxiliary Function Range Inhibit thus preventing operation of the bobtail while this connection is engaged. MEC’s Smart Interlock Technology incorporates a high grade Turck proximity switch that senses the presence of the flange on the ME441F8 Acme cap when secured tightly to the ME868 Series low emission Acme adapter. Mounting hardware and wiring harness that reaches 5’ below the deck of the bobtail is included in the kit.

The MEP105 Adapter makes possible periodic evacuation and testing of a bobtail’s internal backcheck valve. The adapter fits snuggly into the female Acme side of a ME130 which then can be threaded onto the ME868 Series low emission Acme adapter. The adapter pushes the valve poppet to the open position and depressurizes the system for testing purposes.

NOTE: Before using, consult the MEP105 test adapter instruction manual.

Turbo-Flo LE Acme Adapters (continued) MARSHALL EXCELSIOR

ME868MIB(ME868-16 & ME441F8

not included)

MEP105

ME868PIBPatent Pending

HOSE END VALVES & ACCESSORIES

Elaflex Nozzles and Valves GASGUARD

The GG1EHS has a new hybrid single nose piece and is used for the refueling of light duty/Autogas vehicles and storage tanks. The GG1 series has outstanding operational performanceand low maintenance requirements. This nozzle cannot discharge LPGas to the atmosphere when not coupled and lever is actuated.

The GG20HS was designed to reach into, and connect to, deep-seated filler valves, as associatedwith forklift truck cylinders and RV filler valves in similarly difficult locations

The GG10 has been designed to fit to hose reels for dispensing bulk LPGas to small / mediumtank and industrial storage facilities. The nozzle is robust and exhibits a high level of operator safety. With the GG10 it is impossible to open the valve and release gas into the atmosphere if the nozzle is not connected to a certified 1-3/4’’ ACME fill point. The technology within the GG10 removes the possibility of serious injury or the misuse of LPG during the transport and handling phases of refueling.

GG1EHS

GG20HS

GG10

The GG10-45 is the same nozzle as the GG10 with a 45º dual-axis swivel which allows the driver more flexibility when connecting the nozzle with hard to reach fill points, such asunderground tanks or overhead fill points. The dual plane swivel reduces the moment load on the nozzle/fill point. The hose also follows path of least resistance and minimizes the strain and kinking force on the hose after the hose tail.

The G11R is used for the containment of leaking fill points during and after each delivery. Gasis released by unscrewing GG10 + GG11 >1 turn. Gas is released through an external screw. Thedual spool safety feature to positively seal to fill point even when unit is unwound ¾ of a turn. The safety feature of the GG10 is maintained with the nozzle attached. The nozzle valve will remain closed even when the lever is actuated in an uncoupled position.

HOSE END VALVES & ACCESSORIES

• High strength aluminium alloy • Stainless steel components• Long service without distortion• Nozzle will safely seal with filler valve, even

if seal gasket is missing

GG1EHS & GG20HS FEATURES: • Used with reed switch nozzle boot systems • Guided extended ACME 1-3/4” thread minimizes cross-threading and unsafe connections• Latching option (not UL approved)

• Light weight and robust design • Stainless Steel used throughout, increasing

the lifetime of the nozzle• Integrated 360° rotating swivel as standard• Anodised aluminium parts for protection

against salt and dirt contamination

GG10 FEATURES: • Completely repairable • Nozzle will safely seal with filler valve, even

if seal gasket is missing• Long reach to access deeply recessed fill

point• GG10-45: 45º swivel version of the GG10

• Uses an external screw to discharge the release volume

• Valve will only open when connected to a 1-3/4” ACME fill point

G11R FEATURES: • Minimal pressure drop

GG10-45

G11R

ZVG 2EURO UL

NB-ZVG

Item No. Description Flow Rate Release Volume Description

GG1EHS Elaflex Light Duty LPGas Nozzle 15.85 gal/min 1.7 cm³ 1-3/4” ACME x 6 TPI Form

GG20HS Elaflex Light Duty LPGas Nozzle 15.85 gal/min 1.7 cm³ 1-3/4” ACME x 6 TPI Form

GG10 Elaflex High Flow LPGas Nozzle 100.39 gal/min 11 cm³ 1-3/4” ACME x 6 TPI Form

GG10-45 Elaflex High Flow LPGas Nozzle with 45º Dual-axis Swivel 100.39 gal/min 11 cm³ 1-3/4” ACME x 6 TPI Form

G11R Elaflex Safety Back-check Valve — 23 cm³ 1-3/4” ACME

ZVG 2 EURO UL Elaflex EURO Push-on Connection Autogas Dispenser 13,2 gal./min < 1 cm3

NB-ZVG Elaflex Nozzle Booth — — Aluminium

ZVG 2 EURO UL FEATURES: • Effortless single-handed operation• Low weight of 3.1 Lbs. (1.41 kg) including

swivel• Ergonomic contoured composite lever

• Low hold-open force• Durable easy-rotating swivel for improved

handling

The ZVG 2 EURO UL is the most advanced system is the EURO ‘push-on’ connection to European Standard EN 13760 and UN R 67. Compared to common threaded couplings, EURO connectors incorporate a variety of advantages, such as easy one-handed operation, enhancedsafety features and very low gas release upon uncoupling. This nozzle is UL certified.

The Elaflex Nozzle Booth NB-ZVG is made of aluminium, is easy to mount and serves for an optimal fit of the nozzle. A Reed contact switch can be attached to the rear side of the nozzle booth. To establish contact-less on- and off switching of the dispenser, the nozzle is fitted with a block Magnet ( additional product code ...M ) in the nozzle guard.


Item No. Inlet(FNPT)

Outlet(F. Acme)

HandleStyle

HandleMaterial

FactoryInstalledE-Z TurnSwivel

ExtendedVersion

Accessories

Holster

ME800 1”

1-3/4”

Standard Aluminum No

No MEP801

ME800-6 3/4” Standard Aluminum NoME800WS 1” Standard Aluminum YesME800C 1” Standard Composite NoME800CWS 1” Standard Composite YesME800G 1” Fluted Aluminum NoME800G-6 3/4” Fluted Aluminum NoME800GWS 1” Fluted Aluminum YesME800GC 1” Fluted Composite NoME800GCWS 1” Fluted Composite YesME800EXT 1” Standard Aluminum No

Yes NoME800EXTWS 1” Standard Aluminum Yes

Item No. Description Fits Accessories

MEP801 Bobtail Hose End Valve Holster-Aluminum ME800 Series MEP801H (Urethane Weather Hood)

MEP802 Bobtail Hose End Valve Holster-Aluminumwith All Weather Hood ME800 Series MEP801-04 (Urethane

Holster Strap)

MEP804 Bobtail Quick-Jaw Hose End Valve Holster- Aluminum with All Weather Hood

ME800 Series,AL363 or AL366(Squibb Taylor)

MEP801H (Urethane Weather Hood)

MEP801-04 (Urethane Holster Strap)


ME4H 3/8”-16

155 156

HH

Accessories Item No. Fits 2-1/2” Deep Shackle Padlock Keyed Alike Keyed Different

ME540 ME800, ME810, ME820 Series ME540P-KA ME540P-KD

Hose End Swivel Connections MARSHALL EXCELSIOR

High Flow & Low Emission Hose End Valves MARSHALL EXCELSIOR

Marshall’s High Flow Low Emission Hose End Valves are leading the industry in minimal productloss during disconnect without sacrificing flow. They have instant full-on flow with the added protection of a quick closing, self-locking handle to prevent accidental opening of the valve duringtransport. They are designed to be used at the end of a filling hose on a bobtail, dispensing system or nurse tank.

• All stainless steel component construction• Molded and riveted on valve main seal• Vents less than .50 cc for minimal loss of

product at disconnect• Self-locking toggle handle prevents accidental valve opening• Toggle handle & stem assembly rotate 360°• Durable ductile iron valve body with automotive grade powder coat finish• Stainless steel 1-3/4” female Acme insert

cast into the handle

FEATURES:

• No additional adapters or connectors needed for operation

• Optional extended version offers 6” of additional reach for filling underground containers or other hard to reach applications• Optional composite style offers a durable

lightweight handle that is resistant to frosting and cold transfer during the filling operation• Optional factory installed EZTurn stainless steel swivel

ME800

High FlowModel

ME800G

Hose End Valve Locks are designed to prevent valve operation while in place, eliminating the possibility of accidental discharge and/or theft of product. Simply slide the lock over the handle/bonnet of the hose end or quick acting dispensing valve. For maximum security a common padlock can be installed.

• 3/8” diameter through holes for standard 2-1/2” shackle style padlock

FEATURES:

Hose End Valve Lock MARSHALL EXCELSIOR

• All stainless steel construction

Hose End Valve Holster MARSHALL EXCELSIOR

The Hose End Valve Holster is designed to provide a durable and convenient receptacle to storebobtail hose end delivery valves during over-the-road transit. This holster can be mounted fully above deck or partially below deck in left or right hand hose reel applications with an ergonomicangle providing optimum conditions for delivery personnel.

• All aluminum and stainless steel construction• Urethane anti-vibration valve sleeve to

prevent incidental damage to delivery valve

FEATURES:

• Machined adjustment ribs for easy, secure height adjustment

• Deck backing plate and all mounting hardware supplied

MEP801

MEP801H

The Hose End Swivel Connector allows the hose end valve to rotate 360° creating an easier connection to the tank filler valve while under pressure. It also promotes hose life by preventingtwisting and kinking during reeling and unreeling from hose reel.

ME850SS Series• All stainless steel construction for maximum durability and corrosion resistance• Large bearing surface for increased

strength and durability

FEATURES:

• 360° rotation under maximum working pressure of 400 PSIG

• UL Listed seal pack design allows for long life with no maintenance required

ME540

ME800GWS

ME800EXTWS

MEP804

Grounding Stud MARSHALL EXCELSIOR

The Grounding Stud is designed to help prevent static electricity from being generated due to friction from the pump. In some cases static electricity can build-up enough to create an ignition source and cause an explosion. ME4H

HOSE END VALVES & ACCESSORIES HOSE END VALVES & ACCESSORIES

Item No. Inlet (FNPT) Outlet (MNPT)

ME850SS-6 3/4” 3/4”ME850SS-6/8 3/4” 1”ME850SS-8 1” 1”ME850SS-8/6 1” 3/4”ME850SS-10/8 1-1/4” 1”


Item No. Description TemperatureRange Accessories

ME200PIB Sensor Bracket Assembly for ME200 Wheel Chocks

-20° to+160° F.

ME200EXT(Standoff

Extension Kit)ME200PIBK Sensor Bracket Assembly with ME200 Wheel Chocks

ME217PIB Sensor Bracket Assembly for ME217 Series

MEP801PC/20(20’ Proximity

Cable)

MEP801PC/30(30’ Proximity

Cable)

IncludesWater Tight

Receptacle Plug

ME503PIB Sensor Bracket Assembly for ME503-16 & ME252-16ME807PIB Sensor Bracket Assembly for ME807 SeriesME808PIB Sensor Bracket Assembly for ME808 SeriesME868PIB Sensor Bracket Assembly for ME868 Valve SeriesMEP801PIH Sensor Assembly with MEP801 Hose End Valve Holster

MEP802PIH Holster W/Proximity Interlock Sensor Assembly withAll Weather Hood

MEP804PIH Bobtail Quick-Jaw Hose End Valve Holster withProximity Interlock Sensor Assembly

MEP801PIK Interlock Retro Fit Kit for MEP801 Hose End Valve HolsterMEP-801PIKL

Low Temperature Interlock Retro Fit Kit for MEP801 Hose End Valve Holster

-50° to+160° F.

ME890PIB Universal Sensor Bracket Assembly for Enclosures -20° to+160° F.


MEP082 Universal Spring Loaded Utility Bracket

Item No. No. of Relays LED PowerIndicator

InlineFuse

CableLength Accessories

MEP801PCK/20 1

Yes Yes

20’ MEP801PC/20(20’ Proximity Cable)

MEP801PC/30(30’ Proximity Cable)

Includes Water TightReceptacle Plug

MEP801PCK/30 1 30’MEP802PCK/20 2* 20’MEP802PCK/30 2* 30’

MEP803PCK/30 3** 30’

Item No. Height Length Width

ME200 7” 10” 7”

157 158

HH Wheel Accessory Item No. Height Length Depth Chocks Standoff Included Extension Kit

ME200B 7-3/4” 20” 7” No ME200EXTME200BK 9-3/4” 20” 8” Yes ME200EXT

Wheel Chock Brackets are designed to provide a durable and convenient receptacle to storewheel chocks during over-the-road transit. Durable aluminum construction and molded inserts prevent damage to wheel chocks. For installations that require additional mounting clearance a standoff extension kit is available.

Universal Utility Brackets provide a safe and secure method to mount and retain hand tools such as shovels, picks, brooms or other equipment for bobtail or utility vehicles during over the road transit.

INTERLOCK TECHNOLOGY

Wheel Chock Bracket MARSHALL EXCELSIOR

ME200PIBK

ME200

Marshall Excelsior’s Wheel Chocks are designed with a “Double Grip” handle for easy carryingand dual traction grips for the road and tire. The aluminum material makes the wheel chock lightweight and able to withstand the toughest environments. Turn the wheel chock upside downand the points on top of the wheel chock will dig into the snow, ice and mud to prevent sliding.Durable safety yellow powder coat finish.

Wheel Chock MARSHALL EXCELSIOR

ME200BK

CHOCK BLOCKS & UTILITY BRACKETSmart Interlock Technology MARSHALL EXCELSIOR

MEP801PIH

MEP802PCK/20

ME890PIB ME217PIB MEP801PIK

Smart Interlock Technology Wiring Harness Kits MARSHALL EXCELSIOR

* One additional cable required (MEP801PC/20 or MEP801PC/30)** Two additional cables required (MEP801PC/20 or MEP801PC/30)

MEP082

Universal Utility Bracket MARSHALL EXCELSIOR

• Cast aluminum body for maximum durability• Vinyl coated for maximum security• All stainless steel spring and mounting

hardware

FEATURES:


Item No.F.

Acme MNPTServiceType

Brass Brass WingNut/Steel

Nipple

Steel*Knurled

NutWingNut

KnurledNut

WingNut

Extended HandleStandard Fluted

Liquid

ME100 — — — — — — 1-1/4” 3/8”ME101 — — — — — — 1-1/4” 1/2”ME110 ME110C — — — ME635-4 ME635G-4 1-3/4” 1/2”ME111 ME111C — ME111S ME111SC ME635-6 ME635G-6 1-3/4” 3/4”

— — — — ME113SC — — 1-3/4” 3/4” FNPTME112 ME112C — ME112S ME112SC ME635-8 ME635G-8 1-3/4” 1”

— — — — — ME635-10 ME635G-10 1-3/4” 1-1/4”

— ME120**ME120WR

ME120S**ME120SWR — ME121S**

ME121SWR — — 2-1/4” 1-1/4”

— ME130B**ME130BWR

ME130**ME130A***ME130WR

— ME130S**ME130SWR — — 3-1/4” 2”

Vapor

ME140 — — — — — — 1-1/4” 3/8”ME141 — — ME141S — — ME645G-4 1-1/4” 1/2”

— — — — — — ME645G-6 1-1/4” 3/4”— — — — — ME646-4 ME646G-4 1-3/4” 1/2”

ME150 ME150C — ME150S ME150SC ME646-6 ME646G-6 1-3/4” 3/4”ME151 ME151C — ME151S ME151SC ME646-8 ME646G-8 1-3/4” 1”

— — — — — ME646-10 ME646G-10 1-3/4” 1-1/4”— — ME160 — ME160S — — 2-1/4” 1-1/4”

159 160

HH

Filler Valve Hose End Handle

Handle Swivels Factory Extended Additional Item No. F. Acme M. Acme

Style Material

Vent Valve Installed Version Keys Connection Connection

ME570 No No No ME571 Yes* No No ME571H Standard Brass Yes* No No ME572 Yes No No ME572EXT Yes No Yes —ME572EXTHD 1-3/4” 1-3/4” Heavy Duty Cast Aluminum Yes No Yes ME574 Standard Brass Yes Yes No ME574EXT Standard Brass Yes Yes Yes ME574EXTHD Heavy Duty Cast Aluminum Yes Yes Yes ME578 Standard Brass Yes No No ME578-02ME578C Heavy Duty Brass Yes No No ME578-02

HOSE END ADAPTERS FILLER & VAPOR COUPLINGS

Hose End Fill Check Adapters are intended to be attached to the LP-Gas delivery truck hoseoutlets. They feature minimal flow restriction which allows for fast delivery while providing an integral check valve to prevent further product loss if the tank fill valve fails to close. In the eventthe tank fill valve should fail, leave the fill adapter connected to the fill valve and disconnect thefiller hose end valve. Then place the filler valve cap onto the fill adapter. The tank fill valve shouldbe repaired immediately.

To increase flow up to 30 percent over standard hose end filler adapters use the ME578 hoseend fill adapter. It is a full-flow, manually operated hose end fill adapter where the user controlswhether the valve is open or closed, providing maximum protection against product discharge.

Hose End Fill Check Adapters MARSHALL EXCELSIOR

* ME571 and ME571H allows the hose end valve to swivel while connected to the filler hose end adapter

• Integral breakaway feature in the event of truck roll away leaving check intact on tank

• ME570, ME572, ME574, ME578 shortest overall height in the industry allowing

adapters to fit inside tank hood• ME571 has a floating internal seat design

which allows check to swivel freely when installed on hose end valve

• ME571H has same features as standard ME571 but with 30% MORE FLOW

• ME578 has a full-port design which allows for full flow

- Removable shutoff key and key ring supplied

FEATURES:

ME578

ME571

ME572

ME571H

ME570

ME574

ME574EXT

Filler and Vapor Couplings MARSHALL EXCELSIOR

*Rated for LP-Gas and NH3 | **Does not include a factory installed retaining ring | *** Includes factory installed filter screen | Pressure rated for 400 WOG

ME130S ME130A ME635G Series

Filler and Vapor Couplings are used as connections between the hose and transfer valve. The filler coupling is designed to provide different connections for the end of a hose (inlet) or an angle, globe or quick acting valve (outlet) when transferring liquid. The vaporcoupling is designed to be used with valves having an upper check mechanism. The nose piece on the vapor coupling opens the checkvalve allowing vapor equalization.

The extended style has a stainless steel female Acme nut insert cast into the heavy duty aluminum handle. All filler and vaporcouplings come with a factory installed retaining ring unless noted. The retaining ring limits the travel of the handle or nut duringdisconnect reducing spin-offs and promoting proper venting of the captured product.

ME635 Series

Wing Nut

ME110

Filler Coupling

Knurled Nut

ME150

Vapor Coupling

• Extended versions provide an additional 7” for use on underground tanks

- Prevents pinching or cutting of the delivery hose on the protective tank collar

- Eliminates dangerous extensions that do not incorporate the appropriate fill check device

- Eliminates unsafe stacking of multiple fill check adapters to obtain the desirable fill connection height

- Overall length allows adapter to fit inside protective tank collar

- Optional heavy duty aluminum handle with a stainless steel 1-3/4” female Acme

insert cast into the handle

ME572EXTHD


Item No.

M. Acme MNPT FNPTBrass Steel*

No Screen1/8” FNPT

Side Port

FactoryInstalledScreen

No Screen1/8” FNPT

Side PortME498-4/2 — — — — 1-1/4” 1/2” 1/4” **ME498-6/3 — — — — 1-1/4” 3/4” 3/8” **

— — — ME520S-8 — 1-1/4” 1” —— — — ME521S-4 — 1-3/4” 1/2” —

ME215 — — ME215S — 1-3/4” 3/4” —ME216 — — ME216S — 1-3/4” 1” —ME217 ME217J ME217A ME217S ME217SJ 1-3/4” 1-1/4” —ME233 ME233J — ME233S ME233SJ 2-1/4” 1-1/4” —ME502-12/8 — — — — 2-1/4” 1-1/2” 1” **ME502-16/10 — — ME502S-16/10 — 2-1/4” 2” 1-1/4” **ME502-16/12 — — — — 2-1/4” 2” 1-1/2” **ME503-16 — ME503A-16 ME503S-16 — 3-1/4” 2” —ME503-20 — ME503A-20 — — 3-1/4” 2-1/2” —ME262 — ME262A ME262S — 3-1/4” 3” —

Item No.

M.Acme

FNPT/MNPT

Brass Steel*Factory Machined

1/4” FNPTwith Vent Hole

Factory InstalledBrass Vent

Valve

FactoryInstalled StainlessSteel Vent Valve

Factory Machined1/4” FNPT

with Vent Hole

FactoryInstalled Brass

Vent Valve

Factory InstalledStainless Steel

Vent ValveME252J-16 ME252JB-16 ME252JS-16 ME252SJ-16 ME252SJB-16 ME252SJS-16 3-1/4” 2” FNPTME503J-16 ME503JB-16 ME503JS-16 ME503SJ-16 ME503SJB-16 ME503SJS-16 3-1/4” 2” MNPT

161 162

HH

Item No. M Acme M Acme Brass Steel *

ME209 ME209S 1-3/4” 3/8”-16


MEP503 Conical Filter Screen Only for 3-1/4” M Acme Adapters 30 Mesh - Stainless SteelMEP503K Conical Filter Screen and Retainer for 3-1/4” M Acme Adapters 30 Mesh - Stainless Steel

Item No. Brass

Steel* M. Acme FNPT MNPT

No Screen Installed ScreenME498-4/2 — — 1/4” 1/2”**ME498-6/3 — —

1-1/4” 3/8” 3/4” **

ME192 — — 1/2” —ME193 — — 3/4” —ME210 — — 1/4” —ME211 — — 3/8” —ME212 — — 1-3/4” 1/2” —ME213 — ME213S 3/4” —ME214 — ME214S 1” —ME502-12/8 — — 1” 1-1/2” **ME502-16/10 — ME502S-16/10 2-1/4” 1-1/4” 2” **ME502-16/12 — — 1-1/2” 2” **ME250 ME250A — 1-1/4” —ME251 ME251A —

3-1/4” 1-1/2” —

ME252-16 ME252A-16 ME252S-16 2” —ME508-24 ME508A-24 ME508S-24 3” —

* Rated for LP-Gas and NH3 | ** Male thread outside and female thread inside

ACME ADAPTERSACME ADAPTERS

*Rated for LP-Gas and NH3

The ME209 Series is designed to hold the hose end valve secure when it is not in use.

ME503-16

ME503KMEP503

Acme Adapterwith Screen

ME209 ME270

ME215S

Acme Adapters MARSHALL EXCELSIOR

ME192

ME212

ME252S-16


* Rated for LP-Gas and NH3 | ** Male thread outside and female thread inside

* Rated for LP-Gas and NH3 | To add a factory installed screen use an “A” after the prefix number i.e. ME252AJB-16 | Pressure rated for 400 WOG

ME503J-16 ME503JB-16 ME503JS-16


Part No. M.Acme

M.AcmeBrass Steel *

ME270 — 1-1/4” 1-1/4”ME273 ME273S 1-3/4” 1-3/4”ME275 ME275S 2-1/4” 2-1/4”ME277 ME277S 3-1/4” 3-1/4”


ME233S


163 164

HH

Item No. Accessory Brass Steel*

F. Acme Style Cap Cap with Cap with Cap Cap with Cap with Chain Cable

Only Chain Cable Only Chain Cable Only** Only

ME229 ME229-1 — ME229S ME229S-1 — 1-3/4” Pin Hole MEP148 —ME229F ME229F-1 ME229F-1C ME229FS ME229FS-1 ME229FS-1C 1-3/4” Knob MEP167 MEP168ME431F ME431F-1 — ME431FS ME431FS-1 — 2-1/4” Knob MEP167 MEP168ME431R ME431R-1 — — — — 2-1/4” Tapped Hole MEP167 MEP168ME441F ME441F-1 ME441F-1C ME441FS ME441FS-1 ME441FS-1C 3-1/4” Knob MEP167 MEP168ME441R ME441R-1 — ME441RS ME441RS-1 — 3-1/4” Tapped Hole MEP167 MEP168

Item No. Accessory Plastic F. Acme Style Chain Cap Only Cap with Chain Only** ME108 ME108-1 1-1/4” Pin Hole MEP147ME109 or ME109-1 or

1-3/4” Pin Hole MEP148ME109-NH3* ME109-NH3-1*ME106 ME106-1 3-1/4” Pin Hole MEP183

Item No. Accessory Brass Steel*

F. Acme Style Flange

Cap with Cap with Cap with Cap Cap with Cap with Diameter

Chain Cable

Flange Flange Flange

Only Flange Flange Only Only

and Chain and Cable and Chain and Cable

ME229F5 ME229F5-1 ME229F5-1C ME229FS5 ME229FS5-1 ME229FS5-1C 1-3/4” Knob 5” MEP167 MEP168ME441F8 ME441F8-1 ME441F8-1C ME441FS8 ME441FS8-1 ME441FS8-1C 3-1/4” Knob 8” MEP167 MEP168ME441RS ME441R8-1 — — — — 3-1/4” Tapped Hole 8” MEP167 MEP168

Item No.

Accessories Inlet and No. of MNPT x 1-3/4 F. Acme Adapter

Angle Globe Outlet Side Ports Short Short Extended

Brass Steel* Steel*

ME810-4 ME820-4 1/2” 1 ME110

— ME635-4

ME110C ME635G-4

ME810-6 ME820-6 3/4” 1 ME111 ME111S ME635-6

ME111C ME111SC ME635G-6

ME810-8 ME820-8 1” 1 ME112 ME112S ME635-8

ME112C ME112SC ME635G-8

Quick Acting Dispensing Valves - Series ME810 MARSHALL EXCELSIOR

Acme Caps MARSHALL EXCELSIOR

*Rated for LP-Gas and NH3 | **MEP147 ring fits over 3/4” MNPT; MEP148 ring fits over 1-1/4” MNPT | NOTE: Red and yellow versions available.

ACME CAPS, PLUGS, & CHAINSACME CAPS, PLUGS, & CHAINS

ME229-EL1-3/4” F. Acme x

1/2” Male Flare 90°

ME229 ME441RS

ME441FS-1CCable Included

*Rated for NH3 | ** MEP147 ring fits over 3/4” MNPT; MEP148 ring fits over 1-1/4” MNPT

ME106

ME109-NH3

Acme Caps with Flange MARSHALL EXCELSIOR


ME441F8

The Flange allows for easy operation of pneumatic or proximity interlock switches which control the safety systems of transport vehicles. The stainless steel flange is flush mounted to the Acme cap.


Dispensing valves are designed to be used at the end of a filling hose for bobtail, dispensingsystem or nurse tank filling operations. These valves have instant full-on flow with the added protection of a quick closing, self-locking handle to prevent accidental opening of the valve during transport.

ME810 Series

ME820 Series

• All stainless steel internal components• Self-locking toggle handle prevents accidental operation• Durable ductile iron valve body with automotive grade powder coat finish

LV440 AND LV440L SERIES FEATURES: • Toggle handle and stem assembly rotate 360°• Stainless steel factory installed vent valve

DISPENSER VALVES & ADAPTERS

Flange

Knob

ME441F-1Chain Included

Pin Hole Tapped Hole


Item No. BodyStyle

Inlet& Outlet(FNPT)

No. ofSidePorts

AccessoriesMNPT x 1-3/4 F. Acme Adapter

ShortBrass

ShortSteel*

ExtendedSteel*

ME821-4

Globe

1/2”

2

ME110ME110C — ME635-4

ME635G-4

ME821-6 3/4” ME111ME111C

ME111SME111SC

ME635-6ME635G-6

ME821B-4** 1/2” ME110ME110C — ME635-4

ME635G-4

ME821B-6** 3/4” ME111ME111C

ME111SME111SC

ME635-6ME635G-6

165 166

HH

Item No.

Moto-Seal Inlet Outlet Application

Protective Part No. Brass Cap

ME220F ME220FSN 1-1/4” Female Acme 1/4” FNPT Fuel Line —ME220M — 3/8” FNPT 1-1/4” Female Acme Service Valve ME220FPME790 ME790SN 1-1/4” Female Acme 1/4” MNPT Filler Valve —

Item No.

Moto-Seal Inlet Outlet Application

Protective Part No. Brass Cap

ME220FL ME220FLSN 1-1/4” Female

1/4” FNPT Fuel Line — Left Hand Acme

ME220ML — 3/8” FNPT 1-1/4” Female

Service Valve ME220FLP Left Hand Acme

ME790L ME790LSN 1-1/4” Female

1/4” MNPT Filler Valve — Left Hand Acme

Item No. Factory

Non-Locking Locking Inlet Outlet Installed

Vent Valve

ME791C ME792C 1/2” FNPT 1/4” FNPT NoME791CJ ME792CJ 1/2” FNPT 1/4” FNPT YesME791D ME792D 1/2” FNPT 1/2” FNPT NoMD791DJ ME792DJ 1/2” FNPT 1/2” FNPT Yes

DISPENSER VALVES & ADAPTERSDISPENSER VALVES & ADAPTERS

ME821 Series

Engine Fuel Filler Valves and Connectors MARSHALL EXCELSIOR

• Knurled body on the fuel line connector and filler valve allows for an easy hand tight

connection even under tank pressure• Works in conjunction with all mating forklift

connectors and filler valves• ME220F series has a durable riveted valve

stem, chrome plated body and wrench flats for easy installation

• ME220M has two seals—an O-ring to minimize product loss during connection

FEATURES:

and a gasket to seal the two connectors during filling operations

• Moto-Seal connector and filler offers - Replaceable tip for maximum service life - Positive seal every time with less than

.3 CC product loss at disconnect - 3 layers of security against possible leaks or connection failures when the O-ring

and flat gasket are intact on the male connector

ME220FSN

ME790SN

ME220F

ME220M

Vapor Service Engine Fuel Valves and Connectors MARSHALL EXCELSIOR

ME220MLThe CGA 789 Quick Closing Couplings are designed for use with vapor service motor fuelapplications. Incorporates all the same features as the standard and Moto-Seal motor fuel fillervalves and connectors. The left hand Acme thread allows service on outdoor motor fuel propaneequipment including lawn mowers, etc.

ME790LSN ME220FLSN

Moto-SealReplaceable Tip(ME795-3-02)

Quick Acting Toggle Valves MARSHALL EXCELSIOR

Quick Acting Toggle Valves are primarily used on cylinder filling operations and industrialapplications where quick and precise on/off operation is necessary.

NOTE: This valve flows in one direction. Installing the valve in the opposite direction of the arrowmay cause the valve to not close properly and/or pump pressure may open the valve.

• Positive shutoff• Corrosion resistant brass construction• One hand operation• Optional factory installed vent valve for

safe release of captured product

FEATURES:

ME791C

ME792C ME791CJ

Quick Acting Dispensing Valves MARSHALL EXCELSIOR

*Rated for NH3 | ** Includes MEJ400 Brass Vent Valve

• All stainless steel internal components• Reduced size and weight for easier handling• Self-locking toggle handle prevents

accidental operation• Durable ductile iron valve body with

FEATURES:

automotive grade powder coat finish• Toggle handle and stem assembly rotate 360°• Factory installed 1/4” FNPT plugged ports


1/2” High Flow Low Emission Quick Acting Hose End Valves

Item No. Description Inlet Outlet

Propane Flow@ 10 PSIGPressure

Differential


Differential

HandleStyle

HandleMaterial

ME777-4 Male SN POL Filler Valve

1/2”FNPT

M. POL 5.2 10.4 Spin on Brass

ME778-4 Female QCC (Type I) Filler Valve F. QCC 5.2 10.4 Spin on Brass

ME779N-4 Female QCC Quick Connect Filler Valve F. QCC 5.2 10.4 Quick Connect Composite

ME779-4 Heavy Duty Female QCC QuickConnect Filler Valve F. QCC 5.2 10.4 Quick Connect Aluminum

Quick Acting Hose End Valves - High Flow Low Emission MARSHALL EXCELSIOR

These Quick Acting Hose End Valves are leading the industry in minimal product loss during disconnect without sacrificing flow. They have instant full-on flow with the added protection ofa quick closing, self-locking handle to prevent accidental opening of the valve during handlingor storage. They are designed to be used at the end of a filling hose on dispensing systems equipped for filling containers with QCC Type I OPD or F. POL type valves.

3/4” High Flow Low Emission Quick Acting Hose End Valves

Item No. Description Inlet Outlet


Differential


Differential

HandleStyle

HandleMaterial Accessories

ME777-6 Male SN POL Filler Valve

3/4” FNPT

M. POL 5.2 10.4 Spin on Brass

ME850SS-6ME778-6 Female QCC (Type I) Filler Valve F. QCC 5.2 10.4 Spin on Brass

ME779N-6 Female QCC Quick Connect Filler Valve F. QCC 5.2 10.4 Quick Connect Composite

ME779-6 Heavy Duty Female QCC QuickConnect Filler Valve F. QCC 5.2 10.4 Quick Connect Aluminum

POL Filler CouplingsItem No. Inlet Outlet Handle Style Body/Nipple Material OAL

ME388 1/4” MNPT Male Soft Nose POL Knurled - 2” Dia. Bass/Brass 2-11/16”ME390 1/4” MNPT Male Soft Nose POL Heavy Duty Forged Bass/Brass 6”ME390S 1/4” MNPT Male Soft Nose POL Heavy Duty Forged Brass/Stainless Steel 6”

AdaptersItem No. Inlet Outlet Handle Style Converts POL Filler Coupling toME392 Female POL 1-5/16” Female Acme Knurled Type I (QCC) Filler CouplingME393-2 Female POL 1-5/16” Male Acme — Male Type II / Quick Fill Connector

ME394 1-5/16” Male Acme/Female POL 1-1/4” Female Acme Knurled Motor Fuel Filler Coupling

ME568 Female POL 1-3/4” Female Acme Knurled Tank Filler Coupling

167 168

H H

DISPENSER VALVES & ADAPTERS

• All stainless steel internal component construction

• Molded then retained and captured for field repair-ability on valve main seal

• Vents less than .04 cc for minimal loss of product at disconnect

• Self-locking toggle handle prevents accidental valve opening

FEATURES: • Toggle handle and stem assembly rotate

360° for maximum ergonomic flexibility and comfort

• Available in Male POL and Female Type I/QCC fill connections

• Type I F. QCC features composite quick connect option for easy on/off and reduced repetitive motion

ME778-4L.E. Quick Acting

F. QCC x 1/2” FNPT Inlet

ME777M. POL

ME778F. QCC

ME779NF. QCC QuickConnect Filler

ME779N-4L.E. Quick Connect FillerF. QCC x 1/2” FNPT Inlet

ME777-4L.E. Quick Acting

M. POL x 1/2” FNPT Inlet

DISPENSER VALVES & ADAPTERSPOL Filler Couplings & Adapters MARSHALL EXCELSIOR

* Replacement M. QCC/F. POL gasket - Part No. MEW3

These POL Filler Couplings make filling DOT propane cylinders with a POL connection quick and easy. A few turns allow the soft nose POL to seal and unseal from the mating POL connection with minimal effort and loss of product. The long body models allow the filler coupling handle to remain outside the fixed collar of the cylinder. Can be used on manual, electric or hydraulic system. In a manual system a shutoff valve (ME791C, ME791CJ, ME792C or ME792CJ) should be used with the filler coupling.

These Adapters allow for quick conversion from a POL connection to various filling applications for retailers who fill multiple cylinder types through the same Type I (QCC) connection. Simply hand tighten the adapter to the POL filler connection (ME388 or ME390 Series).

The ME393-2 allows for quick conversion from M. QCC (ME516) or F. POL (ME390) Fill Adapter to a Male Type II/Quick Fill Connector.

ME388Coupling

ME392Adapter

ME394Adapter

ME393-2Adapter

ME568Adapter

ME390Coupling

ME390SCoupling


169 170

HH


ME796 1/4” MNPT 1-5/16” Female Acme Quick Connect


MET443 3/8” Male Flare 1/4” FNPT (2 Ports)MET444 3/4”-16 Male / 1/4” FNPT 1/4” FNPT (2 Ports)MET445 3/4”-16 Male / 1/4” FNPT 1/4” FNPT (3 Ports)

Item No. Inlet Outlet Side Port

ME709 1/4” FNPT 1/4” MNPT —ME229-EL 1-3/4” F. Acme 1/2” Male Flare —ME8346 5/16” ID 3/8” Female Flare 1/4” FNPT

Item No. Inlet Outlet Handle Style Body/Nipple

OAL Material

ME515 Knurled Brass/Brass 7”ME516 1/4” MNPT 1-5/16” Female Acme Heavy Duty Forged Brass/Brass 6”ME516S Heavy Duty Forged Brass/Stainless Steel 6”

Item No. Inlet Outlet Handle Style

Converts Type 1 (QCC) Filler Coupling to

ME393 Male Soft Nose POL Knurled POL Filler CouplingME393HD

1-5/16” Male Acme/Female POL Male Soft Nose POL Heavy Duty Forged POL Filler Coupling

ME394 1-1/4” Female Acme Knurled Motor Fuel Filler CouplingME569 1-3/4” Female Acme Knurled Tank Filler Coupling

FILLER COUPLINGS & ADAPTERSENGINE FUEL BULKHEADS & CARB FITTINGSEngine Fuel Bulkheads MARSHALL EXCELSIOR

Marshall Excelsior’s Engine Fuel Bulkheads provide a stationary point for motor fuel lines to passthru sections of sheet metal.MET444

MET443

Carburetion Filter and Fittings MARSHALL EXCELSIOR

The Gas/Air Filter is used to filter foreign materials and/or particles from LP-Gas systems suchas motor fuel/carburetion systems. Also designed to be used to filter air supply lines for internaland emergency shutoff valve actuator systems.

Carburetion Hose Fitting ME8346 enables the installation of a 1/4” MNPT hydrostatic relief valvein a safe, protected area. This two-piece carburetion hose fitting fits all stainless steel braided LP-Gas hose with a 5/16” ID. The tank valve side has a 3/8” female flare swivel and zinc platedfor maximum corrosion resistance.

Marshall’s Fitting ME229-EL allows connection of a motor fuel service line from 1-3/4” femaleAcme vapor outlet.

ME709

ME8346ME229-EL90° Angle

Type I (QCC) Quick Filler Coupling MARSHALL EXCELSIOR

Type I (QCC) Quick Filler Coupling designed to provide a fast, reliable connection for fillingcylinders with Type I (QCC) style valves. The snap on/snap off design is intended to reduce laborand repetitive motion associated with threaded type filler couplings. This easy to operate fillercoupling is durable, lightweight and will withstand the harshest working conditions while reducing cylinder valve thread wear.

NOTE: A quick closing shutoff valve must be used with this coupling.

• Durable glass filled nylon handle• Easy snap on/off action for quick fill operation• All stainless steel internal components• Large bore stainless steel stem for increased flow

FEATURES: • Right or left hand operation• Universal filler connection for all Type I

(QCC) service valves

Type I (QCC) Quick Filler Coupling

(ME791CJNot Included)

Type I (QCC) Filler Couplings and Adapters MARSHALL EXCELSIOR

These full size Type I (QCC) Filler Couplings make filling DOT propane cylinders with a QCC connection quick and easy. Just a few turns allows the filler to attach and remove the coupling with minimal effort and loss of product. A longer body allows the filler coupling handle to remainoutside the fixed collar of a cylinder. Can be used on a manual, electric or hydraulic system. In a manual system a shutoff valve (ME791C, ME791CJ, ME792C or ME792CJ) should be usedwith the filler coupling.

WARNING: It is illegal to fill a 40 lb. or less DOT propane cylinder that has a standard POL connection.

ME516S

ME515

The Type I (QCC) Thread replaces the POL connection on 40 lb. or less DOT propane cylinders.Marshall Excelsior has developed numerous adapters to allow quick conversion from Type I (QCC)to different fill applications for retailers who fill both 40 lb. or less and larger propane cylindersthrough the same line. Simply hand tighten the adapter to the Type I (QCC) filler coupling (ME515or ME516 Series).

ME569

ME393HDME393 ME394


171 172

HH


Connection Connection

129A001 LPG 1/4” Air 3/8” NPT Standard Handwheel Valve, Male Thread Without SRV129A002 Refrigerant 1/4” NPT - Air 3/8” NPT Standard Handwheel Valve, Male Thread, With and Without SRV 129A003* LPG 1/4” NPT Air 3/8” NPT Standard Handwheel Valve, POL Outlet, Female POL Thread Valves With and Without SRV129A006 LPG 1/4” NPT Air 3/8” NPT Omeca Coupling, 66.0.290.1024129A009 LPG 1/4” Air 3/8” OPD - Female POL Thread Valve with Check-Lock With and Without SRV

Item No. Connection OAL AccessoryBracket Style Lanyard Style FNPT Length Reassembly Tool

ME860S-6 ME861S-6 3/4” 6” MEP128-6ME860S-8 ME861S-8 1” 6-3/4” —ME860S-10 ME861S-10 1-1/4” 7-3/4” —

Kosan LPG Filling Heads CAVAGNA GROUP

BREAKAWAY COUPLINGSLPG FILLING HEADS

*Left hand version is available

Cavagna Group’s Filling Heads are made of corrosion-resistant materials such as stainless steel,brass, aluminum and special polymers. The rubber materials are developed and manufactured according to the requirements of EN 549 as well as Kosan’s own strict specifications. The Cavagna Group quality control system carries as minimum an ISO 9001 certification and is continuously assessed by QCB.

Breakaway Couplings MARSHALL EXCELSIOR

Breakaway Couplings are designed to provide a safe way to transfer LP-Gas and NH3 without sacrificing flow. The FloKillTM Breakaway Coupling flows both directions and protects against expensive loss of product or equipment damage if a pull-away occurs during a transfer operation.One end of the breakaway coupling should be attached to a fixed or sturdy point. In the event of an excessive amount of pull force, the breakaway coupling will separate and immediately shutoff product flow in both directions.

To reconnect the valve, pressure needs to be relieved from both ends of the line, therefore itis recommended that a safe way to bleed down the line is provided upstream and downstream.After the lines have been depressurized use Marshall Excelsior’s re-installation tool (MEP128-6)for 3/4” or slide the male end into the female side and pull the collar back until they lock. Afterreconnection the line must be tested using Marshall Excelsior Leak Detector to check for leaksbefore any product is transferred. The breakaway coupling may be used on vapor or liquid lineson transports, delivery trucks, motor fuel containers, fill cabinets and other miscellaneous filling operations.

NOTE: It is recommended that breakaway couplings be safety tested monthly to confirm that proper separation occurs in the event of a pull-away. Dry air is suggested for a source ofpressure during testing.

• Nitrile soft seat provides positive shutoff both upstream and downstream of source

• 100 - 300 lb. of force required for disconnect• Approximately 100 lb. of force to reconnect

FEATURES: • Large internal bore for increased flow• Durable plated steel construction• Rated for LP-Gas and NH3

ME860S-6

ME861S-6

MEP128-6Coupling Not Included

Filling Head


173 174

H H


P4-100 Single Hose Dispenser for Meters and Fuel Management SystemsP4-150 Dual Product Dispenser for Meters and Fuel Management SystemsP4-200 Dual Hose Dispenser for Meters and Fuel Management Systems


P4-SECP-E Economy Series Integrated Station Control PanelP4-SECP VFD Fully Integrated Station Control PanelP4-SECP Single and Three Phase Full Control Panels


P4-ECO Air Internal Valve System for Tanks

AUTOGAS DISPENSERS

All P4 Dispensers are full retail capable autogas dispensers designed to be used with cylinder and/or Gasguard fill nozzles. The P4 Series is functional, durable and fully NETP certified forinstallation with NTEP approved meters and fuel management systems. The dispensers areskid mountable to most dispensing skid systems as well as island mountable for multi-dispenserfuel islands, with or without pit. The P4 Series can be mounted within 5’ of other productdispensers in accordance with NFPA 58 for low emissions dispensers. They can also be mounted remotely from the pump for remote fueling points and mounted with third party fuel management pedestals.P4-100

• Electronic display, fully NCWM retail approved• Push-to-Start / Stop button• Illuminated On button• Electronic calibration and totalizer• Automatic electronic temperature compensation

FEATURES: • Dual product pricing or 5 level pricing • Pre-wired for connection to most card

reader systems• Solenoid flow control for accuracy and theft

prevention• Built in accordance with UL 495 / 1238, and

NFPA 58 / 30A

Autogas Dispensers

• Liqua-Tech LPM102, Neptune 4DMD, or Liquid Controls MA4

• Optional 2” receipt printer, 3” roll

METER OPTIONS: • Optional integrated Motor-starter with

overload protection• Optional upgrade to proprietary P4-ParaFUEL fuel management system

P4-150

P4-200

FUEL MANAGEMENT EQUIPMENTLPG Control Panels

The P4-SECP-E integrates all the electrical control elements into a single panel mount box and isdesigned specifically for filling small bottles or single/dual hose autogas dispensers. This unit isavailable in single or three phase, from 2 - 7.5 hp, and has a mounting size of 12” x 9” x 9”.The P4-SECP requires a properly rated circuit breaker in the supply panel (20 - 30 amps).

The P4-SECP is a single panel mount box designed for running larger autogas fleets and retail stations with 2 or more dispensers and 1 pump with 5 - 7.5hp three phase motors. Base models have a mounting size of 41” x 24” x 12”. The VFD gives the additional benefit of soft starts withprogrammable ramp up, contributing to longer pump and motor life. The dispenser isolation relays to protect dispensers from back feed voltage.

The P4-SECP also has a single panel mount box and is capable of single or 3 phase service (from 5 - 10 hp), 120/230/240 and 480 vac. It is designed for running large autogas fleets and retail stations with 2 or more dispensers and 1-3 pumps. Mounting size is 20” x 16” x 10”.

• P4-SECP-E and P4-SECP models have a NEMA 4X fiberglass enclosure. P4-SECP have NEMA 4/12 metal exterior enclosure

• Galvanized back plane with DIN rail mounted components for easy connections• Motor starter/disconnect with current limit

integrated• Manual reset on overload protection• Through door disconnect• Hooded emergency stop button, breaks all

power to the station when depressed• Optional “HOA” switch for manual over-ride testing

FEATURES: • 1-10 second delay in motor start to delay pump start when opening internal valves• 6 Amp breaker for dispenser• Optional auxiliary 6 Amp breaker for third

party card readers• Optional LED Pilot light for run indication• All connection points labeled• Satisfies all NFPA and NEC requirements

for single point station electrical integration• Can be prewired and assembled to individual station specifications• Units built to order based on site specifications

P4-SECP-E

P4-SECP VFD

P4-SECP-E

Internal Valve System

The P4-Eco-Air Internal Valve System is designed for the rigors of propane internal valveoperation and is safer, less costly, and better for the environment than gas or nitrogen systems.

• Industrial grade compressor - oil free and maintenance free

• Vertical 2 gallon reservoir, with self-drain solenoid, PLC controlled

• Heavy duty regulator and filter with auto drain

FEATURES: • Computerized controls and pressure sensors• Continues to operate with “Small Leak

Detection” after warning light• Automatic shut-down with “Major Leak

Detection” and flashing warning indicatorP4-ECO


Item No. Description Inlet Outlet Filter Element Flow Rate *

ME680-8 High Capacity Dispensing Filter 1” FNPT 1” FNPT 20 micron 35 GPM/LPG

LPG/NH3 High Capacity Dispensing Filter MARSHALL EXCELSIOR

Inline FiltersItem No. Description

ME204 1/4”MNPTx1/4”FNPT Brass Gauge Dampener/FilterME709 1/4”FNPT x 1/4”MNPT Inline Fuel Filter

Pressure Gauges MARSHALL EXCELSIOR

Item No. Dial Diameter Probe Length

MEJ700 2” 4”MEJ701 2” 6”MEJ702 3” 4”MEJ703 3” 6”

Container Thermometers MARSHALL EXCELSIOR

175 176

H H

AUTOGAS ACCESSORIES

The new ME680 LPG/NH3 Dispenser Filter is designed to remove 99.9% of solid contaminants.These contaminants can be introduced into the system during the refining process from holding tanks as well as the delivery trucks used to transport the liquid fuel. This filter is used to protect critical engine components such as fuel injectors on propane powered vehicles which include: shuttle buses, delivery trucks and vans, taxi cabs, lift trucks, as well as turf maintenance vehicles.

The filter housing is constructed from high strength forged aluminum. The entire housing ispowder coated for long term outdoor use. There are two internal primary seals inside the filterelement used to prevent contaminants from entering into the downstream. There is a 1” hex nut located on the bottom of the bowl for easy removal and maintenance.

The element is constructed of pleated micro glass media, reinforced with an epoxy coated wire for added strength and corrosion resistance. This pleated element design offers a higher contaminant-loading capacity and offers a lower pressure drop than other standard elements. The element also has a pleated steel inner retainer for additional strength and durability.

• High-grade forged aluminum body construction

• Durable powder coated exterior• 5/16-18 UNC tapped mounting holes for

easy installation• 1” hex nut on bottom of bowl for easy

maintenance• Pleated element offers higher contaminant

loading capacity and lower pressure drop

FEATURES: • 35 GPM/LPG @ 6.2 PSI pressure differential• Removes solid contaminants from LPG/

NH3 (20 micron rated element)• 1” FNPT inlet/outlet connections• 350 PSI maximum pressure• 1/4” FNPT plugged ports both upstream

and downstream of the filter element

ME680-8-ERKME680-8

Replacement Filter Elememt

ME206

ME709

Port Size: 1” NPTMax Pressure: 350 PSIGMax. Temp: 175° F (79° C)Head Material: AluminumInternal Components: Stainless SteelBowl: AluminumSeals: NitrileWeight: 5.5 lbsLength: 8.07”Width: 5.00”

SPECIFICATIONS:

ME680

THERMOMETERS & GAUGES

These Pressure Gauges are designed to measure the pressure of gas or liquid. MarshallExcelsior offers two types of gauges, dry and glycerin filled. With a glycerin filled gauge, the life of the gauge is extended, vibration of the pointer is minimized and condensation, caused by humid air inside the gauge, is eliminated.

To determine the correct gauge, environment along with normal operating system pressure must be considered. The pressure range of the gauge should be twice the normal system pressure to maximize gauge life and accuracy.

These thermometers are designed for use in LP-Gas or NH3 storage tanks, nurse tanks, bobtails and transports. These stainless steel, dust and water proof thermometers feature a 1/2” MNPT connection with a temperature range from –40° to +120° Fahrenheit. Accuracy +/- 1 percent full range.

MEJ502

Item No.PSIG Dial Size Fill Type

1/4” MNPT Bottom Mount 1/4” MNPT Back MountMEJ520 — 0-5 2-1/2” DryMEJ500 MEJ510 0-15 2” DryMEJ603LP-01* — 0-15 2-1/2” GlycerinMEJ501 MEJ511 0-30 2” DryME10BTK-04 — 0-30 2-1/2” GlycerinME50ECO-2 — 0-30” WC 2-1/2” DryMEJ502 MEJ512 0-60 2” DryMEJ503 MEJ513 0-100 2” DryMEJ504 — 0-160 2” DryMEJ505 — 0-200 2” DryMEJ600-02 MEJ516 0-300 2” DryMEJ603HP-01* — 0-300 2-1/2” GlycerinMEJ580*** — 0-300 4” DryMEJ542** — 0-400 2-1/2” Glycerin

— MEJ524* 0-400 2-1/2” GlycerinMEJ552* MEJ526** 0-400 2-1/2” Glycerin

*Brass Pipe Thread; Stainless Steel Bezel | ** Stainless Steel Gauge | *** Plated Steel Gauge

MEJ542

MEJ701

MEJ513

Item No. Fits

MEJ2.5GB 2-1/2” Dial, Bottom Mount Pressure Gauge

Pressure Gauge Protective Boot MARSHALL EXCELSIOR

The Protective Boot fits over the pressure gauge dial to extend the life and accuracy of dry and liquid pressure gauges. This boot helps protect the dry pressure gauge’s internal components and helps prevent dents on liquid pressure gauges which cause the gauge to leak. MEJ2

ProtectiveBoot

BottomMount

BackMount


Gas Box™ Convenience Outlet MARSHALL EXCELSIOR

177 178

HH

Item No. Inlet Flow Capacity Handwheel Thermal

Description Color Protection

ME517EV 1-5/16” Female Acme Full Flow Black Yes Evacuation Coupling

Item No. Handwheel Thermal Outlet Inlet Flow Capacity

Color Protection1/4” MNPT 1/4” Hose Barb 3/8” Hose BarbME517 ME517-25H ME517-38H 1-5/16” Female Acme 50 SCFH Air/100,000 BTUH Black YesME518 ME518-25H ME518-38H 1-5/16” Female Acme 100 SCFH Air/200,000 BTUH Green YesME519 ME519-25H ME519-38H 1-5/16” Female Acme 200 SCFH Air/400,000 BTUH Red Yes

Item No. Fits Brass Black Vinyl

ME392P ME952-07 1-5/16” Female Acme

QCC CAPS, ADAPTERS, & CONNECTORSQCC CAPS, ADAPTERS, & CONNECTORS

The Type I (QCC) Connectors ( ME517, ME518 and ME519 Series) are designed with a built-in excess flow feature and a positive shutoff that will not allow gas to flow until the connector is fully engaged. In case of a fire the built-in thermal protection on the QCC connector meltsallowing the nipple to disengage from the tank connection and stop the flow of propane. TheseQCC connectors also provide a positive back check seal at disconnect to eliminate the propanein the hose from being released into the atmosphere.

To connect a Type I (QCC) connector to a cylinder, close the cylinder valve and the control valvesto all connected appliances. Hand tighten the QCC onto the cylinder and slowly open the cylindervalve. If the valve is opened too quickly, the excess flow device will be activated closing the flowof propane to the appliance. If the excess flow device is activated, close appliance control valvesand wait 60 seconds to allow pressure in the line to equalize. Additional equalization time may be needed depending on the length of the hose. Turn on appliances by following themanufacturer’s suggested lighting procedures.

NOTE: The Type I (QCC) thread replaces the POL connection on 40 pound or less DOTpropane cylinders.

WARNING: An excess flow valve will not activate if there is a break or leak downstream of the valve that does not equal or exceed the closing flow of the valve or if the excess flow valve installed exceeds the flow capacity of the system.

Type I (QCC) Connector MARSHALL EXCELSIOR

ME517

ME518-25H

ME519

ME517EV

Type I (QCC)/OPD Valve Cap MARSHALL EXCELSIOR

Type I (QCC) / OPD Valve Cap is designed to protect the 1-5/16” male Acme threads on Type I (QCC) or OPD type cylinder valves. Using a cap will reduce the likelihood of inadvertent damage to the valve’s threads, shutoff mechanisms and sealing surfaces during storage or refurbishment.

ME952-07

ME392P ME392P installed on20 lb. cylinder

MEC’s Gas Box™ Convenience Outlet are designed to eliminate the need for a 20 LB cylinderor modifications generally needed to plumb an outdoor appliance to a DOT or ASME stationarytank. The Gas Box™ utilizes the standard LP-Gas outdoor appliance regulator and connector. Simply hard plumb a gas line from the first stage regulator into the Gas Box™. Then thread the standard Type I (QCC) or POL connector onto the Gas Box™, turn on the shutoff valve andenjoy continuous LP-Gas flow. Both models provide full capacity operation at 10 PSIG or higherinlet pressures for all outdoor appliances without modifications. The Gas Box™ is an easy wayto guarantee increased propane sales. It eliminates the need for 20 pound cylinders, allowing the customer to purchase any appliance without modifications.

• Universal Type I (QCC) / female POL outlet connection

• Primary shutoff valve for each outlet connection

• Secondary safety shutoff poppet at each outlet for zero discharge at disconnect

FEATURES: • For use with 10-250 PSIG inlet pressure• Universal mounting hardware• Hinged cover with latching mechanism• Weather resistant high density

polyethylene case

Model ME951 – Single outlet*• 750,000 BTU/HR – 100 PSIG inlet pressure / Outlet regulated @ 9.5 – 13 in. W.C. (11” nom.)• 450,000 BTU/HR – 10 PSIG inlet pressure / Outlet regulated @ 9.5 – 13 in. W.C. (11” nom.)

Model ME952 – Dual outlet *One outlet closed• 750,000 BTU/HR – 100 PSIG inlet pressure / Outlet regulated @ 9.5 – 13 in. W.C. (11” nom.)• 450,000 BTU/HR – 10 PSIG inlet pressure / Outlet regulated @ 9.5 – 13 in. W.C. (11” nom.)

Both outlets open (at each outlet)• 750,000 BTU/HR – 100 PSIG inlet pressure / Outlet regulated @ 9.5 – 13 in. W.C. (11” nom.)• 325,000 BTU/HR – 10 PSIG inlet pressure / Outlet regulated @ 9.5 – 13 in. W.C. (11” nom.)

FLOW RATE/CAPACITY SPECIFICATIONS: ME952GRY

ME951BLK

ME952IVY

MER428

Item No.

Inlet OutletNo. ofColor

OutletsAccessories

Color

Black Gray Ivory

ME951BLK ME951GRY ME951IVY 1/2” FNPT 1-5/16” Male Acme/Female POL SingleMER428-60 = 60” Extension HoseMER428-120 = 120” Extension Hose(Male QCC/Female POL x Female QCC)MER429-60 = 60” Extension HoseMER429-120 = 120” Extension Hose(Male QCC/Female POL x Red FemaleQCC-400,000 BTU/H)

ME952BLK ME952GRY ME952IVY 1/2” FNPT 1-5/16” Male Acme/Female POL Dual



ME-GMC4 Quick Disconnect Assy - 1/4” FNPT x 1/4” MNPT NippleME-GMCL-4 1/4” Quick Disconnect Ball Valve Coupler - 1/4” FNPT with Dust CapME-GMC4-02 1/4” Quick Disconnect Nipple x 1/4” MNPT AdapterME-GMC4-03 1/4” Quick Disconnect Nipple x 1/4” Hose Barb AdapterME-GMC6 3/8” Quick Disconnect Assembly - 3/8” FNPT Coupler x 3/8” FNPT NippleME-RVSDC-4 Replacement Dust Cap - 1/4” QD Coupler with Lanyard

Low Pressure Quick Disconnect Couplings MARSHALL EXCELSIOR

The Low Pressure Quick Disconnect Couplings are designed to provide convenient quick connect and disconnect for low pressure gas appliances with 100% positive gas shut off at female coupler end of the connection. Maximum operating pressure 1/2 PSIG.

• Convenient wrench flats for securing connection points

• One piece coupler body• Durable all brass construction

FEATURES: • Approved for all low pressure

gas applications• For indoor and outdoor applications


ME306 Female CGA 555 1/4” MNPTME307 Female CGA 555 9/16”-18 Male Left HandME308 Female CGA 555 Female POL

CGA 555 Fittings MARSHALL EXCELSIOR

Item No. Cap with Chain

ME309-1 CGA 555

The CGA 555 Adapters are standard cylinder valve outlet connections for liquid butane or propane withdrawal. They are designed to withstand pressures up to 3,000 PSIG.

179 180

HH

Item No. Packaged Inlet Outlet Shutoff Device

ME393-1 — 1/4” FNPT 1-5/16” Male Acme/Female POL —ME393EX — 1/4” FNPT 1-5/16” Male Acme/Female POL .9 GPM Excess Flow*ME393EX1.8 — 1/4” FNPT 1-5/16” Male Acme/Female POL 1.8 GPM Excess Flow*ME398 ME398P** Male Soft Nose POL 1-5/16” Male Acme/Female POL Quick ClosingME399 — 1/4” MNPT 1-5/16” Male Acme/Female POL Quick Closing

*An excess flow device does not provide a 100% shutoff, a small amount of propane may leak ifdisconnected | ** Packaged option consists of a plastic clamshell

Type I (QCC) Installation Adapters provide a safe permanent outlet when installed into the household LP-Gas system. This permanent outlet eliminates the need for smaller containerswhen operating outdoor LP-Gas equipment. It is recommended that a shutoff valve be installedupstream from the adapter inlet to facilitate future servicing. The adapters can be used with both Type I (QCC) and male POL connections.

ME398 and ME399 include an internal shutoff valve which provides a leak free means for outdoorequipment to be safely connected and disconnected without shutting down the entire system.

NOTE: To use the female POL on the ME393 series, simply remove the internal gasket. The gasket must be in place to use the Type I (QCC) connection.

WARNING: An excess flow valve will not activate if there is a break or leak downstream of the valve that does not equal or exceed the closing flow of the valve or if the excess flow valve installed exceeds the flow capacity of the system. Contact the manufacturer for more information regarding the use of excess flow devices.

Type I (QCC) Installation Adapters MARSHALL EXCELSIOR

ME399

ME398P

ME393-1

QCC CAPS, ADAPTERS, & CONNECTORSQCC CAPS, ADAPTERS, & CONNECTORS

ME-GMCL4

ME-GMC4

ME-GMC6

ME-306

ME-308

ME-309-1


181 182

II POL x MNPT Item No. POL Connection POL ConnectionME305 Female Female

Item No.

Male Hard Male Hard

Male Soft

Connection Male POL Description Nose POL

Nose POL Nose POL 90° Angle

ME318, ME318P* ME345 ME1629 7/8” NutME322 — — 7/8” Nut, 3-1/2” OAL — — ME1654 Plastic Handwheel — — ME1654AH Hex Handwheel — — ME1654AR Round HandwheelME319 ME348 — 1-1/8” NutME1690, ME1690P* — ME1641 1/4” MNPT .9 GPM Excess Flow, 7/8” Nut — — ME1653 .9 GPM Excess Flow, Plastic Handwheel — — ME1653AH .9 GPM Excess Flow, Hex Handwheel — — ME1653AR .9 GPM Excess Flow, Round HandwheelME1692 — — .9 GPM Excess Flow, 1-1/8” NutME1690-EX18 — ME1641EX18 1.8 GPM Excess Flow, 7/8” Nut — — ME1638 #60 Orifice Hole, 7/8” Nut

Item No.

Male Hard Male Hard Hose

Male POL Description Nose POL

Nose POL I.D. 90° AngleME5930 ME1656-78N 1/4” 7/8” NutME5931-78N ME5931-78SN 3/8” 7/8” NutME5930-118N ME1656-118N 1/4” 1-1/8” NutME5931 ME5931-SN 3/8” 1-1/8” Nut — ME1656 1/4” Plastic Handwheel — ME1656AH 1/4” Hex Handwheel — ME1656AR 1/4” Round HandwheelME1683 ME1655-78N 1/4” .9 GPM Excess Flow, 7/8” NutME5931EX-78N ME5931SNEX-78N 3/8” .9 GPM Excess Flow, 7/8” NutME1684 — 1/4” .9 GPM Excess Flow, 1-1/8” Nut — ME1655 1/4” .9 GPM Excess Flow, Plastic Handwheel — ME1655AH 1/4” .9 GPM Excess Flow, Hex Handwheel — ME1655AR 1/4” .9 GPM Excess Flow, Round Handwheel — ME1655EX18-78N 1/4” 1.8 GPM Excess Flow, 7/8” Nut — ME1657 1/4” #60 Orifice Hole, 7/8” Nut

POL x Male Flare Item No. POL Excess Male Connection Flow Flare

ME353 Male Hard Nose — 3/8”ME353-SN Male Soft Nose — 3/8”ME353EX9 .9 GPM 3/8”ME353EX18 Male Hard Nose 1.8 GPM 3/8”ME355 — 1/2”ME355-SN Male Soft Nose — 1/2”ME355EX9 .9 GPM 1/2”ME355EX18 Male Hard Nose 1.8 GPM 1/2”ME356 — 5/8”ME356-SN Male Soft Nose — 5/8”ME356EX9

Male Hard Nose .9 GPM 5/8”

ME356EX18 1.8 GPM 5/8”

POL x MNPT Item No. POL Excess Male Connection Flow Flare

ME284 — 1/4”ME285

Female — 3/8”

ME286 — 1/2”ME287 — 3/4”ME352 — 3/8”ME354

Male Hard Nose — 1/2”

ME354EX9 .9 GPM 1/2”ME354EX18 1.8 GPM 1/2”

POL x FNPT Item No. POL Connection FNPT

ME300 1/8”ME301 1/4”ME302 Female 3/8”ME303 1/2”ME304 3/4”ME351 Male Hard Nose 1/4”ME357 1/2”

Item No. Brass Plastic Style Body Only Body With Chain Body Only

ME1691 ME1691-1 ME970P Male Hard Nose POL Plug

ME1699 — — Female POL Cap ME1699

POL ADAPTERSPOL ADAPTERSMale POL x 1/4” MNPT MARSHALL EXCELSIOR

*Packaged option consists of a plastic clamshell

Male HardNose POL

Male SoftNose POL

PlasticHandwheel ME345

Male POL x Hose Barbs MARSHALL EXCELSIOR

Hex Handwheel

Round Handwheel


Single Piece POL Adapters MARSHALL EXCELSIOR

WARNING: An excess flow valve will not activate if there is a break or leak downstream of the valve that does not equal or exceed the closing flow of the valve or if the excess flow valve installed exceeds the flow capacity of the system. Contact themanufacturer for more information regarding the use of excessflow devices.

ME970P

ME1691

POL Cap and Plugs MARSHALL EXCELSIOR

ME285

ME353

ME353EX18

ME303


183 184

II

POL ADAPTERSPOL ADAPTERS

POL Thread Clean Out Tool is designed for use with any female POL thread or valve inlet opening.Allows operator to safely remove debris and other foreign material from female .880-14 NGO left hand threads (female POL) without damaging threads. Simply thread clean out tool into female POL threads using handwheel until the tool reaches the final thread. Reverse and removetool carefully. Reverse tool and use attached 7/8” diameter bottle brush to perform final clean out operation. Blow out any remaining debris by using a compressed air line.

• Constructed from hardened tool steel and plated for maximum product life

• Four clearance flutes to allow debris to be channeled away from threads

FEATURES: • Convenient 7/8” diameter wire brush for

final clean out

POL Thread Clean Out Tool MARSHALL EXCELSIOR

WARNING: The POL thread clean out tool is strictly intended for use as a cleaning device and in no way should be used as a gauge to determine the usability of the thread. (Always refer to NFPA 58 and follow the appropriate guidelines prior to installing LP-Gas lines).

MEP100

Tee Check Manifolds MARSHALL EXCELSIOR

The Tee Check Manifolds are designed to connect two cylinders. The check keeps the two tanks equalized and allows each tank to be changed without disrupting the flow of propane toappliances or dispensing large amounts of LP-Gas into the atmosphere from the other tank.When changing out a tank, simply close the tank valve and disconnect. The check willautomatically move to the closed tank valve side to seal off the inlet of that tank allowing minimal LP-Gas discharge into the atmosphere. Primary uses are for mobile homes, single appliances, recreational vehicles or summer cottages.

The manual changeover works the same as the check except it requires the consumer to manually close the manifold valve on the side of the tank being changed over.

ME1701A

MEP456A

* Manual change over | ** Packaged option consists of a plastic clamshell

Multiple Cylinder Tee Block Manifolds MARSHALL EXCELSIOR

These Manifolds are designed to connect multiple cylinders to automatic changeover regulators.These manifolds have no check and are primarily for systems requiring more than one cylinderto be in operation at a time. The appropriate pigtail must be used to connect the manifold inletto the service cylinder valve.


ME1701B

ME-T9-444

ME1704BItem No. Packaged Part

No. Inlet Inlet Outlet Nut Size

ME1701A — Female POL Female POL Male HardNose POL 7/8”

ME1702A — Female POL Female POL Male HardNose POL 1-1/8”

ME1705A — Female POL Female POL 1/4” MNPT —

ME1700A ME1700A-P** 1/4” FemaleInverted Flare

1/4” FemaleInverted Flare 1/4” MNPT —

MEP456A* — 1/4” FemaleInverted Flare


ME1700A

Item No. Inlet Inlet Outlet Nut Size

ME1701 Female POL Female POL 1/4” FNPT —ME1701B Female POL Female POL Male Hard Nose POL 7/8” ME1702B Female POL Female POL Male Hard Nose POL 1-1/8”ME1701B-SN Female POL Female POL Male Hard Nose POL 7/8”

ME1701X Female POL Female POL Male .9 GPM ExcessFlow Hard Nose POL 7/8”

ME1701B-X-SN Female POL Female POL Male .9 GPM ExcessFlow Hard Nose POL 7/8”

ME1704B Female POL Female POL Female POL 1-1/8”

ME1700B 1/4” FemaleInverted Flare


ME-T9-444 1/4” FNPT 1/4” FNPT 1/4” MNPT —

ME1705A


185 186

II

9/16”-18 Male Left Hand

Item No. Description OAL

ME690-4-6 Dielectric Union 1/2” MNPT x 3/8” Male Flare 3-3/8”ME690-6-6 Dielectric Union 3/4” MNPT x 3/8” Male Flare 3-1/2”ME690-4-8 Dielectric Union 1/2” MNPT x 1/2” Male Flare 3-1/2”ME690-6-8 Dielectric Union 3/4” MNPT x 1/2” Male Flare 3-5/8”ME690-4-10 Dielectric Union 1/2” MNPT x 5/8” Male Flare 3-5/8”ME690-6-10 Dielectric Union 3/4” MNPT x 5/8” Male Flare 3-3/4” Item No.

Male Hard Male Soft Connection POL Description Nose POL Nose POL

ME1650 ME1650SN 7/8” NutME1651 — 1-1/8” NutME1689 ME1645-78N .9 GPM Excess Flow, 7/8” Nut — ME1645 .9 GPM Excess Flow, Plastic HandwheelME1687 — .9 GPM Excess Flow, 1-1/8” NutME1689-EX18 — 1.8 GPM Excess Flow, 7/8” Nut

Item No. Hose Barb Hose Barb

Nut Only Hose Threads

Assembly Only I.D.

ME23C ME23C-1 ME23C-2 1/4” 9/16”-18 Female Left HandME23E ME23E-1 ME23C-2 3/8” 9/16”-18 Female Left Hand

Outlet Bushings Item No. Male Left Hand Thread ThreadME24C 9/16” - 18 1/4” MNPTME24E 9/16” - 18 3/8” MNPTME24F 9/16” - 18 1/2” MNPTME26C 9/16” - 18 9/16” - 18 Male Left Hand

FLARE/BRASS FITTINGSPOL ADAPTERS

ME23C

Soft Nose POL

Hard Nose POL

ME24C

* An excess flow device does not provide a 100% shutoff, small amounts of propane may leak ifdisconnected | ** Packaged option consists of a plastic clamshell with insert card

Last Chance Adapters provide a quick way to change from a 20 pound cylinder to a 1 pound disposable cylinder. Can be used to connect a small 1 pound disposable cylinder to a gas grill or other appliance.

NOTE: To use the male POL on the ME393 series, simply remove the internal gasket. The gasket must be in place to use the Type I (QCC) connection.


FLARE/BRASS FITTINGS

ME480

The ME690 Series Dielectric Unions are intended to isolate metallic piping from sources of electrical current and to help prevent galvanic corrosion. The ME690 dielectric union would typically be installed at the ASME tank directly downstream of the first stage regulator but priorto underground piping and/or at the inlet of the second stage regulator above ground at the dwelling. Thus, it protects the underground metallic piping from corrosion and electrical current.

MEC Space Saver Dielectric Unions MARSHALL EXCELSIOR

ME690-4-8

• Heavy duty brass construction• Convenient Male NPT x Male SAE flare

connection to minimize potential piping leak points and extra fittings

• Compact size for tight spaces

FEATURES: • Wide wrench flats for easy installation• Will not conduct an electrical charge from

one side of the union to the other

ME480EX

ME481P

Last Chance Adapters MARSHALL EXCELSIOR


High Pressure Gas Connections MARSHALL EXCELSIOR

Item No. PackagedPart No. Inlet Outlet Description

ME480 — 1”-20 Female 1-5/16” Male Acme/Female POL Full FlowME480EX — 1”-20 Female 1-5/16” Male Acme/Female POL .9 GPM Excess Flow ME480EX1.8 — 1”-20 Female 1-5/16” Male Acme/Female POL 1.8 GPM Excess FlowME481 ME481P** 1”-20 Female 1-5/16” Male Acme/Female POL Shutoff Poppet


187 188

II

Reducing Unions Item No. O.D. Tube Size

MEF42-8-6 1/2” x 3/8” MEF42-10-6 5/8” x 3/8” MEF42-10-8 5/8” x 1/2”

Forged Swivel Nuts Item No. O.D. Tube Size

ME-US4-6 3/8” ME-US4-8 1/2” ME-US4-10 5/8”

Reducing Forged Swivel Nuts Item No. O.D. Tube Size

ME-US4-8-6 1/2” x 3/8” ME-US4-10-8 5/8” x 1/2”

Male Connectors Item No. O.D. Tube Size MNPT

MEF48-4-2 1/4” 1/8”MEF48-4-4 1/4” 1/4”MEF48-6-2 3/8” 1/8”MEF48-6-4 3/8” 1/4”MEF48-6-6 3/8” 3/8”MEF48-6-8 3/8” 1/2”MEF48-6-12 3/8” 3/4”MEF48-8-4 1/2” 1/4”MEF48-8-6 1/2” 3/8”MEF48-8-8 1/2” 1/2”MEF48-8-12 1/2” 3/4”MEF48-10-6 5/8” 3/8”MEF48-10-8 5/8” 1/2”MEF48-10-12 5/8” 3/4”MEF48-12-8 3/4” 1/2”MEF48-12-12 3/4” 3/4”

Female Connectors Item No. O.D. Tube Size FNPT

MEF46-4-4 1/4” 1/4”MEF46-6-4 3/8” 1/4”MEF46-6-6 3/8” 3/8”MEF46-6-8 3/8” 1/2”MEF46-6-12 3/8” 3/4”MEF46-8-6 1/2” 3/8”MEF46-8-8 1/2” 1/2”MEF46-8-12 1/2” 3/4”MEF46-10-6 5/8” 3/8”MEF46-10-8 5/8” 1/2”MEF46-10-12 5/8” 3/4”

Forged Female Elbows Item No. O.D. Tube Size FNPT

MEF54-6-6 3/8” 3/8”MEF54-6-8 3/8” 1/2”MEF54-6-12 3/8” 3/4”MEF54-8-6 1/2” 3/8”MEF54-8-8 1/2” 1/2”MEF54-8-12 1/2” 3/4”MEF54-10-8 5/8” 1/2”MEF54-10-12 5/8” 3/4”

Male Tee Item No. O.D. Tube Size

MEF44-6-6-6 3/8” MEF44-8-8-8 1/2” MEF44-10-10-10 5/8”

Forged Male Elbows Item No. O.D. Tube Size MNPT

MEF49-4-6 1/4” 3/8”MEF49-6-4 3/8” 1/4”MEF49-6-6 3/8” 3/8”MEF49-6-8 3/8” 1/2”MEF49-6-12 3/8” 3/4”MEF49-8-4 1/2” 1/4”MEF49-8-6 1/2” 3/8”MEF49-8-8 1/2” 1/2”MEF49-8-12 1/2” 3/4”MEF49-10-8 5/8” 1/2”MEF49-10-12 5/8” 3/4”

2 Way Forged Elbows Item No. O.D. Tube Size

MEF55-6 3/8” MEF55-8 1/2” MEF55-10 5/8” MEF55-12 3/4”

Flare Plugs Item No. O.D. Tube Size

MEP2-4 1/4” MEP2-6 3/8” MEP2-8 1/2” MEP2-12 3/4”

Pipe Threads Unions Item No. MNPT MNPT

MEF216-2 1/8” 1/8”MEF216-4 1/4” 1/4”MEF216-6 3/8” 3/8”MEF216-6-8 3/8” 1/2”MEF216-8 1/2” 1/2”MEF216-12 3/4” 3/4”

Flare Caps Item No. O.D. Tube Size

ME1695-4 1/4” ME1695-6 3/8” ME1695-8 1/2” ME1695-12 3/4”

Short Forged Nuts Item No. O.D. Tube Size

ME-NS4-4 1/4” ME-NS4-6 3/8” ME-NS4-8 1/2” ME-NS4-10 5/8” ME-NS4-12 3/4”

Full Unions Item No. O.D. Tube Size

MEF42-4-4 1/4” MEF42-6-6 3/8” MEF42-8-8 1/2” MEF42-10-10 5/8”

Reducing Forged Nuts Item No. O.D. Tube Size

ME-NS4-6-4 3/8” x 1/4” ME-NS4-8-4 1/2” x 1/4” ME-NS4-8-6 1/2” X 3/8” ME-NS4-10-8 5/8” X 1/2”

Female Tee Item No. FNPT

ME415-01 1/4”

Tube Nut Item No. O.D. Tube Size

MEF41-6 3/8”

FLARE/BRASS FITTINGSFLARE/BRASS FITTINGSFlare Fittings and Pipe Thread Adapters Flare Fittings and Pipe Thread Adapters


189 190

II

Item No. O.D. Tube Size Length Wall Thickness

CT0450 1/4” 50’ .030 CT0650 3/8” 50’ .032 CT06100 3/8” 100’ .032 CT0850 1/2” 50’ .032 CT08100 1/2” 100’ .032 CT1050 5/8” 50’ .035 CT10100 5/8” 100’ .035

Item No. I. D. Tube Size Length Wall Thickness

KT0460 1/4” 60’ .035 KT04100 1/4” 100’ .035 KT0660 3/8” 60’ .049 KT06100 3/8” 100’ .049 KT0860 1/2” 60’ .049 KT08100 1/2” 100’ .049


LT0460 1/4” 60’ .035 LT04100 1/4” 100’ .035 LT0660 3/8” 60’ .049 LT06100 3/8” 100’ .049 LT0860 1/2” 60’ .049 LT08100 1/2” 100’ .049

Item No. O.D. Tube Size Length Wall Thickness

GT0650 3/8” 50’ .032 GT06100 3/8” 100’ .032 GT0850 1/2” 50’ .032 GT08100 1/2” 100’ .032 GT1050 5/8” 50’ .035 GT10100 5/8” 100’ .035


GTL0460 1/4” 60’ .030 GTL04100 1/4” 100’ .030 GTL0660 3/8” 60’ .035 GTL06100 3/8” 100’ .035 GTL0860 1/2” 60’ .040 GTL08100 1/2” 100’ .040

Item No. Size Reel Length Reel Weight (lb.)

FGP-CS-375-250 3/8” 250’ 37FGP-CS-375-100 3/8” 100’ 17FGP-CS-500-500 1/2” 500’ 98FGP-CS-500-250 1/2” 250’ 52FGP-CS-500-100 1/2” 100’ 24FGP-CS-500-50 1/2” 50’ 14FGP-CS-750-250 3/4” 250’ 70FGP-CS-750-100 3/4” 100’ 31FGP-CS-750-50 3/4” 50’ 18FGP-CS-100-180 1” 180’ 70FGP-CS-100-100 1” 100’ 40FGP-CS-100-50 1” 50’ 22FGP-CS-125-250 1-1⁄4” 250’ 129FGP-CS-125-150 1-1⁄4” 150’ 78FGP-CS-150-250 1-1⁄2” 250’ 182FGP-CS-150-150 1-1⁄2” 150’ 103FGP-CS-200-150 2” 150’ 137

COATED COPPER TUBINGCOPPER TUBINGRefrigeration Copper Tubing, O.D.

CT0650

This item is sold by outside diameter (O. D.)

Type K Copper Tubing, I.D.

This item is sold by inside diameter (I. D.)

Type L Copper Tubbing


Coated Refrigeration Copper Tubing, O.D.

This item is sold by outside diameter (O. D.)

Coated Type L Copper Tubing, I.D.


COATED COPPER TUBING

GT0650

CORRUGATED STAINLESS STEEL TUBING

TracPipe

TracPipe CounterStrike® Tubing OMEGAFLEX

NOTE: Other lengths of TracPipe CounterStrike® Tubing are available. Contact your MTankCo representative for more information.

• Heavy one piece abrasion and lightning resistant jacket

• Up to 125 PSI working pressure• Highest Capacity Rating (EHD)

FEATURES: • Auto Flare® Fitting is both self-flaring and

self-piloting to pipe’s inner diameter• Meets ASTM E84 with respect to flame

spread and smoke density


191 192

II


FGP-FSTF-375 3/8” - 1/2” NPT AutoFlare Female Straight 3/8”FGP-FSTF-500 1/2” AutoFlare Female Straight 1/2”FGP-FSTF-750 3/4” AutoFlare Female Straight 3/4”FGP-FSTF-1000 1” AutoFlare Female Straight 1”FGP-FSTF-1250 1-1/4” AutoFlare Female Straight 1-1/4”FGP-FSTF-1500 1-1/2” AutoFlare Female Straight 1-1/2”


FGP-CPLG-375 3/8” Coupling 3/8”FGP-CPLG-500 1/2” Coupling 1/2”FGP-CPLG-750 3/4” Coupling 3/4”FGP-CPLG-1000 1” Coupling 1” FGP-CPLG-1250 1-1/4” Coupling 1-1/4”FGP-CPLG-1500 1-1/2” Coupling 1-1/2”FGP-CPLG-2000 2” Coupling 2” Item No. Size Description

FGP-SFST-375 3/8” AutoSnap 3/8”FGP-SFST-500 1/2” AutoSnap 1/2”FGP-SFST-750 3/4” AutoSnap 3/4”FGP-SFST-1000 1” AutoSnap 1”FGP-SRING-375 3/8”FGP-SRING-500 1/2”

Spare Snap RingsFGP-SRING-750 3/4”FGP-SRING-1000 1”


FGP-RST500-750 1/2” - 3/4” NPT AutoFlare Reducing 1/2”FGP-RST750-500 3/4” - 1/2” NPT AutoFlare Reducing 3/4”FGP-RST1000-750 1” - 3/4” NPT AutoFlare Reducing 1”


FGP-BFF-375 3/8” Flange Fitting 3/8”FGP-BFF-500 1/2” Flange Fitting 1/2”FGP-BFF-1000 1” Flange Fitting 1” FGP-BFF-1250 1-1/4” Flange Fitting 1-1/4”FGP-TERM-BRAC All Flange L BracketFGP-ELLB-375 3/8” 90° Flange Fitting 3/8”FGP-ELLB-500 1/2” 90° Flange Fitting 1/2”FGP-BF90V-375 3/8” 90° Flange Valve 3/8”FGP-BF90V-500 1/2” 90° Flange Valve 1/2”FGP-BF90V-750 3/4” 90° Flange Valve 3/4”

Item No. Size Reel Length Description

FGP-UGP-375-250 3/8” 250 ft. TracPipe PS-II 3/8” ReelFGP-UGP-500-250 1/2” 250 ft. TracPipe PS-II 1/2” ReelFGP-UGP-500-100 1/2” 100 ft. TracPipe PS-II 1/2” ReelFGP-UGP-750-250 3/4” 250 ft. TracPipe PS-II 3/4” Reel FGP-UGP-750-100 3/4” 100 ft. TracPipe PS-II 3/4” ReelFGP-UGP-100-250 1” 250 ft. TracPipe PS-II 1” ReelFGP-UGP-100-100 1” 100 ft. TracPipe PS-II 1” Reel


FGP-UGF-375 3/8” NPT Male TracPipe PS-II 3/8” Male Adapter FGP-UGF-500 1/2” NPT Male TracPipe PS-II 1/2” Male AdapterFGP-UGF-750 3/4” NPT Male TracPipe PS-II 3/4” Male AdapterFGP-UGF-1000 1” NPT Male TracPipe PS-II 1” Male AdapterFGP-UGC-375 3/8” T/P Cplg TracPipe PS-II 3/8” CouplingFGP-UGC-500 1/2” T/P Cplg TracPipe PS-II 1/2” CouplingFGP-UGC-750 3/4” T/P Cplg TracPipe PS-II 3/4” CouplingFGP-UGC-1000 1” T/P Cplg TracPipe PS-II 1” Coupling

GAS PIPING

Female Straight Fittings TRACPIPE

FemaleStraight Fitting

Couplings TRACPIPE

Coupling

AutoSnap® Straight Fittings TRACPIPE

AutoSnap®

Straight Fitting

Reducing Fittings TRACPIPE

Reducing Fitting

GAS PIPING

Flange Fittings TRACPIPE

Flange Fitting

Underground System PS-II Reels TRACPIPE

FGP-UGP-375-250

Underground System PS-II Adapters and Couplings TRACPIPE

CouplingFGP-UGC-750

Male AdapterFGP-UGF-750


193 194

II


FGP-MI-PC 3/4” x 1/2” x 1/2” (4) Coated ManifoldFGP-MB2 Fits MI-PC Manifold BracketFGP-MI-ST-500 1/2” F- M x 1/2” (2) Stackable ManifoldFGP-MI-ST-750 3/4” F- M x 1/2” (2) Stackable ManifoldFGP-MI-ST Fits MI-ST Stackable Manifold BracketFGP-LC — Load Center w/ BracketFGP-MI-PC-1X 1-1/4” x 1” x 3/4” (4) Large Coated ManifoldFGP-MI-PC-2X 2 x 1-1/2” x 1” (4) Large Coated Manifold


FGP-SP-025 3” x 2” Quarter Striker PlateFGP-SP-050 3” x 7” Half Striker PlateFGP-SP-075 3” x 9” Three Quarter Striker PlateFGP-SP-100 3” x 12” Full StrikerFGP-SP-617 6-1/2” x 17” Striker PlateFGP-FPY-375CT 3/4” Floppy, Fits 3/8” Cut 1 ft.FGP-FPY-500CT 1” Floppy, Fits 1/2” Cut 1 ft.FGP-FPY-750CT 1-1/4” Floppy, Fits 3/4” Cut 1 ft.FGP-FPY-1000CT 1-1/2” Floppy, Fits 1” Cut 1 ft.FGP-FPY-375-50 3/4” Floppy, Fits 3/8”FGP-FPY-500-50 1” Floppy, Fits 1/2”FGP-FPY-750-25 1-1/4” Floppy, Fits 3/4”FGP-FPY-1000-25 1-1/2” Floppy, Fits 1”FGP-FPY-1250-25 2” Floppy, Fits 1-1/4” FGP-FPY-1500-25 2-1/2” Floppy, Fits 1-1/2”FGP-FPY-2000-25 3” Floppy, Fits 2”FGP-915-10H-12BL 1” x 12 yd. Tape, BlackFGP-LCS 1 Quart Non-Corrosive Leak Check Solution


FGP-GC-1 1/2 - 1 IPS Bonding Clamp for 3/8, 1/2 TracPipe® CounterStrike®

FGP-TC-15 3/8” - 1” Cutter No. 15FGP-QDS 1/2” Sturgis Quick DisconnectFGP-ITAG-50 All Installation TagsFGP-TAG-20 All High Pressure TagsFGP-ITAG-50 — Installation Tags


PP08 1/2” CTS Tubing, 500’ Roll - SDR 7 PP12 3/4” IPS Tubing, 500’ Roll - SDR 11 PP16X500 1” IPS Tubing, 500’ Roll - SDR 11 PP20X500 1-1/4” IPS Tubing, 500’ Roll - SDR 10 PP32X250 2” IPS Tubing, 250’ Roll - SDR 11 PP32X500 2” IPS Tubing, 500’ Roll - SDR 11


FGP-MT6-500 1/2” x 6” 6” Meter Termination 1/2”FGP-MT6-750 3/4 x 6” 6” Meter Termination 3/4”FGP-MT6-1000 1” x 6” 6” Meter Termination 1”FGP-MT9-1000 1” 9” Meter Termination 1”FGP-MT12-500 1/2” x 12” 12” Meter Termination 1/2”FGP-MT12-750 3/4” x 12” 12” Meter Termination 3/4”FGP-MT12-1000 1” x 12” 12” Meter Termination 1”FGP-MT-BRAC All Meter Termination BracketFGP-TM-375 3/8” Termination Mount 3/8”FGP-TM-500 1/2” Termination Mount 1/2”FGP-TM-750 3/4” Termination Mount 3/4”FGP-TM-750-500 3/4” x 1/2” Termination Mount 3/4” x 1/2” FGP-TM-1000 1” Termination Mount 1”FGP-90TM-375 3/8” 90° Termination Mount 3/8”FGP-90TM-500 1/2” 90° Termination Mount 1/2”FGP-TM90V-375 3/8” 90° Termination Valve 3/8”FGP-TM90V-500 1/2” 90° Termination Valve 1/2”FGP-TM90V-750 3/4” 90° Termination Valve 3/4”


FGP-T500-750 1/2” x 3/4” Male Tee - Male 3/4”FGP-T500-500 1/2” Female Tee - Female 1/2”FGP-T750-500 3/4” x 1/2” Female Tee - Female 1/2”FGP-T750-750 3/4” Female Tee - Female 3/4” FGP-T1000-1000 1” Female Tee - Female 1”FGP-TF500-T500 1/2” x 1/2” Tee - TracPipe 1/2”FGP-TF750-T750 3/4” x 3/4” Tee - TracPipe 3/4”FGP-TF1000T1000 1” x 1” Tee - TracPipe 1”

GAS PIPING

Manifolds TRACPIPE

Full StrikerFGP-SP-100

Three QuarterStriker PlateFGP-SP-075

Protection TRACPIPE

Protection TRACPIPE

GAS PIPING

PLASTIC PIPEPlastic Pipe

This item is sold in CTS (copper tube size) and IPS (iron pipe size).

Meter Termination and Mounts TRACPIPE

Termination Mounts

Tee Fittings TRACPIPE

Tee Fitting

Tee Reducer Fittings are available in various sizes. Contact your MTankCo representative for more information.

Meter Termination

Manifold


195 196

II


3259-49-0413-66 1/2” CTS x 1/2” CTS x 3/4” IPS3259-49-1304-66 3/4” IPS x 3/4” IPS x 1/2” CTS3259-49-1413-66 1” IPS x 1” IPS x 3/4” IPS


3259-52-1004-66 1/2” CTS 3259-52-1013-66 3/4” IPS 3259-52-1014-66 1” IPS 3259-52-1015-00 1-1/4” IPS 3259-52-1017-00 2” IPS


3259-54-1304-66 3/4” IPS x 1/2” CTS 3259-54-1404-66 1” IPS x 1/2” CTS 3259-54-1408-66 1” IPS x 1” CTS 3259-54-1413-66 1” IPS x 3/4” IPS




0459-56-0800-66 1/2” CTS x 8” long 0459-56-1200-66 1/2” CTS x 12” long 0459-56-2400-66 1/2” CTS x 24” long 1359-56-0800-66 3/4” IPS x 8” long 1359-56-1200-66 3/4” IPS x 12” long 1359-56-2400-66 3/4” IPS x 24” long 1459-56-0800-66 1” IPS x 8” long 1459-56-1200-66 1” IPS x 12” long




5864-15-1604-66 1-1/4” IPS Main x 1/2” CTS 5864-15-1613-66 1-1/4” IPS Main x 3/4” IPS 5864-17-1604-66 2” IPS Main x 1/2” CTS 5864-17-1613-66 2” IPS Main x 3/4” IPS 5864-17-1614-66 2” IPS Main x 1” IPS


0000-33-5481-00 3/4” IPS x 1/2” CTS Chamfer Tool (5/8” O.D.)0000-33-6580-15 1-1/4” IPS Chamfer Tool0000-33-6580-17 2” IPS Chamfer Tool0000-33-5606-00 1” IPS x 1” CTS Chamfer Tool

CON-STAB FITTINGSCON-STAB FITTINGSReducing Tee CON-STAB Couplings CON-STAB

Reducing Tee Coupling

90˚ Elbow CON-STAB Reducing Couplings CON-STAB

Reducing Tee

Reducing Coupling

Repair Couplings CON-STAB Tees CON-STAB

Self-Tapping Tee CON-STAB Chamfer Tool CON-STAB

Repair Coupling Tee

Self-Tapping Tee

Chamfer Tool


197 198

II

Item No. Length Description

1637NX12 12” 1637NX18 18” 1637NX24 24” 1637NX36 36” 1637NX48 48” 1637NX60 60” 1650NX12 12” 1650NX18 18” 1650NX24 24” 1650NX36 36” 1650NX48 48” 1650NX60 60”


1675NPX24 24” 3/4” I.D. / 1” O.D. 1675NPX36 36” 3/4” I.D. / 1” O.D.


10-2132-12 12” 10-2132-18 18” 10-2132-24 24” 10-2132-36 36” 10-2132-48 48”

Item No. Item No. with Constab Size (MPT X PE) Wall Vertical Length Horizontal Length

1253-91-4604-00 1,2 1253-91-4604-25 1,2 1/2” MPT X 1/2” CTS (5/8” OD) PE .090 30” 15”1355-91-4604-00 1,2 1355-91-4604-25 1,2 3/4”MPT X 1/2”CTS (5/8” OD) PE .090 18” 19”1353-91-4604-00 2 1353-91-4604-25 1,2 3/4”MPT X 1/2”CTS (5/8” OD) PE .090 30” 17”1353-91-4612-00 1,2 1353-91-4612-25 3/4”MPT X 1/2” IPS PE SDR-9.3 (.090) 30” 17”1353-91-4613-00 1,2 1353-91-4613-25 1,2 3/4”MPT X 3/4” IPS PE SDR-11 (.095) 30” 16”1353-91-4608-00 1,2 1353-91-4608-25 2 3/4”MPT X 1” CTS (1-1/8” OD) PE .099/.101 30” 16”1453-91-4608-00 1,2 1453-91-4608-25 1,2 1” MPT X 1” CTS (1-1/8” OD) PE .099/.101 30” 16” 1453-91-4614-00 1,2 1453-91-4614-25 1,2 1” MPT X 1” IPS PE SDR-11 (.119) 30” 16”1553-91-4615-00 1,2 1553-91-4615-25 1 1-1/4”MPT X 1-1/4”IPS PE SDR-10 (.166) 30” 22”1553-91-4615-0A 1,2 9953-99-0503-25 1 1-1/4” MPT X 1-1/4” IPS PE SDR-11 (.151) 30” 22”1652-91-4616-00 1,2 1652-91-4616-25 1,2 1-1/2”MPT X 1-1/2”IPS PE SDR-11 (.173) 36” 26”1752-91-4617-00 1,2 1752-91-4617-25 1 2”MPT X 2” IPS PE SDR-11 (.216) 36” 30”

Item No. Size (MPT X PE) Wall

1253-92-1004-36 1/2” MPT X 1/2” CTS (5/8” OD) PE .090 1253-92-1012-36 1/2” MPT X 1/2” IPS PE SDR-9.3 (.090) 1353-92-1004-36 3/4” MPT X 1/2” CTS (5/8” OD) PE .090 1353-92-1012-36 3/4” MPT X 1/2” IPS PE SDR-9.3 (.090) 1353-92-1006-36 3/4” MPT X 3/4” CTS (7/8” OD) PE .090 1353-92-1013-36 3/4” MPT X 3/4” IPS PE SDR-11 (.095) 1353-92-1008-36 3/4” MPT X 1” CTS (1-1/8” OD) PE .099/.101 1453-92-1004-36 1” MPT X 1/2” CTS (5/8” OD) PE .090 1453-92-1012-36 1” MPT X 1/2” IPS PE SDR-9.3 (.090) 1453-92-1006-36 1” MPT X 3/4” CTS (7/8” OD) PE .090 1453-92-1013-36 1” MPT X 3/4” IPS PE SDR-11 (.095) 1453-92-1008-36 1” MPT X 1” CTS (1-1/8” OD) PE .099/.101 1553-92-1008-36 1-1/4” MPT X 1” CTS (1-1/8” OD) PE .099/.101 1453-92-1014-36 1” MPT X 1” IPS PE SDR-11 (.119) 1553-96-1015-36* 1-1/4” MPT X 1-1/4” IPS PE SDR-10 (.116)

APPLIANCE CONNECTORSRISERSStainless Steel Gas Appliance Connectors

3/8” ID / 1/2” OD with 1/2” Female x 1/2” Male

1/2” ID / 7/8” OD with3/4” Female x 3/4” Male

1637NX12

Super-Safe™ Connectors for Mobile Homes DORMONT

Residential Connectors are durable, flexible, and easy to install. Designed with built-in safety features, Supr-Safe connectors help prevent dangerous gas leaks and provide for a long and trouble-free service life.

Dormont Black Appliance Connectors

1/4” ID x 3/8” OD -3/8” MPT x 1/2” FNPT

Black Appliance Connectors are specifically designed for high-temperature applications such as gas logs, fireplace inserts, etc. They reduce glare and hide the connector from view.

1675NPX24

Flex Pipe Risers CON-STAB

Plastic Pipe Risers CON-STAB

1 CSA Approved | 2 IAPMO/UPC Listed

ORDERING NOTE: All Risers come in 36”, 60”, 72”, 84”, and 96” lengths. When ordering, add a dash then the riser length after the prefix Item Number, i.e. XXXXXX-72 indicates a 72 inch length riser.

NOTE: Slide the plastic tubing through the riser to the end and make your connection there, above ground. No connections underground, no coupling needed.

• Simplified compression style anodized service head

• Reusable fitting with Buna seal, strengthened with a spiral steel stiffener

• Integral swivel for easy installation

FEATURES: • Complete with poly liner and lower moisture seal• Meets or exceeds NFPA58 and ANSI standards

* This item does not include a liner sleeve, all other risers come with a liner sleeve.

Flex Pipe Riser

PlasticPipe Riser

Plastic Pipe Riserwith Con-Stab

ID Seal® Couplings

Plastic Pipe Risers are designed to meet or exceed pressure rating of PE pipe per 49 CFR Part 192 and ASTM D2513. It is recommended to use Continental’s Bladed Chamfering Tool. Part numbers listed are for 2406 medium density polyethylene pipe. For part numbers with 3408 high density pipe, contact your MTankCo representative.


199 200

DJJ

Accessories Liquid Liquid Withdrawal Tank Valve Closing Withdrawal 1-5/8” UNF Male

Item No. Material

Excess Flow/ Adapter 3/4” 3/4”

1-1/4” MNPT

Hydrostatic Vent

Flow

GPM FNPT x 1-5/8” UNF MNPT Relief Valve Valve

Brass Steel* Brass Brass Steel* Stainless Steel*

ME449 Brass No — ME458 ME458S ME460*** ME462*** — — MEH225

MEH25/450

ME449H Brass No — ME458 ME458S — — — — Factory Installed MEH225ME449S Ductile Iron* No — — ME458S — — ME462S*** ME462SS***

MEH225SS/350ME449EXS/22 Ductile Iron* Yes 22 — — — — — —

MEH225SS/400ME449EXS/28 Ductile Iron* Yes 28 — — — — — —

MEH225SS/440ME450** Brass No — — — ME601-6 ME601-10 — —

MEJ400MEJ400SCMEJ400/72MEJ402S

Item No. Material Inlet Connection Outlet Connection

ME458 Brass 1-5/8”UNF 3/4” FNPTME458S* Steel 1-5/8” UNF 3/4” FNPTME453 Brass 3/4” NGT 3/4” FNPTME455 Brass 3/4” NGT 3/4” MNPT

Container Two Service Dip Tube Accessories Item No. Material Connection Connection Connection Stainless Steel Stainless Steel MNPT FNPT FNPT Vent Valve Pressure Gauge*

ME830 Ductile Iron 3/4” MNPT 1/4” FNPT 1/8” Included MEJ526

MEJ542MEJ415 Steel 3/4” MNPT 1/4” FNPT 1/8” MEJ402S MEJ542MEJ415G Steel 3/4” MNPT 1/4” FNPT 1/8” Included Included

ME458

DOMESTIC TANK VALVES & ACCESSORIESDOMESTIC TANK VALVES & ACCESSORIES

Liquid Transfer Valves and Adapters MARSHALL EXCELSIOR

*Rated for LP-Gas and NH3 | ** MEJ400 Vent Valve factory installed | *** Includes an excess flow feature

ME450

Liquid Transfer Valves and Adapters provide a safe means by which to transfer liquid from a tankduring an emergency or container relocation. These valves can be equipped with an integral excess flow device for direct product transfer or without when used in conjunction with liquid withdrawal adapter (ME458 Series) and tank valve (ME460 and ME462 Series).

WARNING: An excess flow valve will not activate if there is a break or leak downstream of thevalve that does not equal or exceed the closing flow of the valve or if the excess flow valve installed exceeds the flow capacity of the system. Contact the manufacturer for moreinformation regarding the use of excess flow devices.

• Double O-ring stem seal design ensures leak free operation

• 3/4” MNPT inlet x 3/4” FNPT outlet

FEATURES: • Double lead stem thread ensures quick and

efficient operation

• All stainless steel internal components• Durable ductile iron valve body with automotive grade powder coat finish• Equipped with convenient upstream and

downstream 1/4” FNPT plugged ports for optional accessories

STEEL TRANSFER VALVES FEATURES: • Provides excess flow protection in the event of a downstream connection or line failure• Safety breakaway feature leaves valve seals intact in the event of truck roll-away• 6 - 14 PSIG closing flow pressure differential for maximum product transfer• Fully interchangeable with all existing valve

models and adapters• Meets requirements for installation into

DOT storage containers like bobtails and transports

• Steel model features a rust inhibitor compound between the cap and body

threads to prevent corrosion

TANK VALVE FEATURES:

Liquid Transfer Adapters MARSHALL EXCELSIOR

Liquid Transfer Adapters are designed for use between the liquid transfer shutoff valve and the liquid withdrawal tank valve. These adapters enable the tank valve to open properly and allows a tight seal when transferring liquid. Special threads on the tank valve and the adapter help eliminate tampering.

The ME458 Series fits all new underwriters laboratories listed valves. The ME453 and ME455 fitolder style liquid withdrawal tank valves that are still in service and have not been replaced. Theywill not provide a positive seal during actuation of liquid withdrawal tank valve until fully seated.

ME453

ME455

Combination Valves MARSHALL EXCELSIOR

Combination Valves have a pressure gauge and fixed tube liquid level gauge all in one valve. Theshutoff portion of the valve increases the pressure gauge’s life and accuracy by eliminating constant gauge pressure and allows for easy gauge replacement. To replace a gauge simply closethe valve and open the vent valve to relieve pressure before disassembling pressure gauge.

The valve can be installed at the maximum fill level or an 1/8” MNPT dip tube can be installed on the container connection side to set any liquid level desired. For use in ASME bulk storage containers and DOT transport tank installations.

• All steel and stainless steel component construction

• Integral #54 orifice provides gauge dampening protection

FEATURES: • Durable ductile iron body with automotive

grade powder coat finish or plated steel body

ME830

MEJ415G

MEJ415

* 0-400 PSIG

ME449EXS-22

* Rated for LP-Gas and NH3

ME462S


201 202

DJJ

Item No.Tank

Connection(MNPT)

FillConnection(M. Acme)

BypassReturn Port

(FNPT)

Approximate Excess FlowClosing Flow Hydrostatic

Relief*LiquidGPM/LPG

**VaporSCFH/LPG

ME673DEX-6SP 1-1/4” 1-3/4” 3/4” 58 27,000 MEH225

Multipurpose Filler Bypass Return Valve for Dispensing Applications MARSHALL EXCELSIOR

Item No. Inlet(MNPT)

FillConnection(M. Acme)

Withdrawal(FNPT)

*Fill CapacityGPM/LPG

Approximate Excess FlowClosing Flow Back

Check

Accessories

*LiquidGPM/LPG

**VaporSCFH/LPG

HydrostaticRelief

VentValve

ME673DEX-6**** 1-1/4” 1-3/4” 3/4” 100 58 27,000 NoMEH225*** MEJ400***MEH225SS MEJ402S

ME673DEX-8**** 1-1/4” 1-3/4” 1” 100 58 27,000 NoMEH225*** MEJ400***MEH225SS MEJ402S

ME673DBC-6 1-1/4” 1-3/4” 3/4” 100 N/A N/A YesMEH225*** MEJ400***MEH225SS MEJ402S

ME673DBC-8 1-1/4” 1-3/4” 1” 100 N/A N/A YesMEH225*** MEJ400***MEH225SS MEJ402S

Multipurpose Filler/Withdrawal Valves MARSHALL EXCELSIOR

* For NH3 Flow Rates Multiply by .90 | ** For NH3 @ 100 PSI, Multiply by 1.6 | *** Brass accessories cannot be used for NH3 | ****Available for 45 GPM NH3 closing flow - e.i. ME673DEX-6/45

Multipurpose Filler/Withdrawal Valves are intended for use as a high capacity combination filler and liquid withdrawal valve with a manual shut off device in LPG or NH3 containers. These valves can be equipped with either a soft seat back check or excess flow feature that is internal to the container. Ideally suited for use in dispensing applications as a dual purpose high capacity tank filler valve as well as a liquid return line from the pump bypass valve.

NOTE: For proper operation and performance of the excess flow feature the manual shutoff must be completely open and back seated.

• Plated ductile iron body with 1/4” NPT auxillary plugged port

• All stainless steel internal construction• Supplied with ACME cap and chain assembly

FEATURES: • V-cup Teflon® packing stem seals• Rated 400 PSI/WOG• Removable data plate ME673DBC

ME673DEX


The ME673DEX-6SP is Ideally suited for use as a high capacity combination double check fill andliquid bypass return line shut-off valve. These valves are equipped standard with an integrated excess flow feature that is internal to the tank protecting against tank separation. The preinstalledside mounted ME601-6 double check fill valve allows for safe low emissions container filling ata convenient right angle orientation. The top mount 3/4” FNPT port above integrated shut-off valve seat allows for maximum liquid bypass return flow rates without adding an external line shut-off valve.

NOTE: For proper operation and performance of the excess flow feature the manual shutoff must be completely open and back-seated. For use with LPG only.

For use with LPG only.

• Plated ductile iron body with preinstalled MEH225 hydrostatic relief valve

• All stainless steel internal construction for maximum corrosion resistance

FEATURES: • V-cup Teflon® packing stem seals• Rated 400 PSI / WOG• Preinstalled ME601-6 double

ME673DEX-6SP


203 204

DJJ

Approximate Excess Flow Accessories

Item No. Inlet Fill Connection *GPM/LPG Closing Flow Back

(MNPT) (M. Acme) Fill Capacity Liquid* Vapor** Check Hydrostatic Vent GPM/LPG SCFH/LPG Relief Valve

ME670DBC 1-1/4” 1-3/4” 100 N/A N/A Yes MEH225*** MEJ400***

MEH225SS MEJ402S

ME670DEX**** 1-1/4” 1-3/4” 100 58 27,000 No MEH225*** MEJ400***

MEH225SS MEJ402S

Approximate Accessories

Item No. Inlet Withdrawal Excess Flow Back

(MNPT) (FNPT) Closing Flow Liquid Check Hydrostatic Vent GPM/LPG* Relief Valve

ME671DIBC-6 3/4” 50 MEJ400**

—

MEJ402S ME671DIBC-8*** 1” 58

MEJ400** MEJ402S

ME671D-6 1-1/4” 3/4” 50 No MEH225** MEJ400**

MEH225SS MEJ402S

ME671D-8*** 1” 58 MEH225** MEJ400**

MEH225SS MEJ402S

ME672D 1” 78 MEH225** MEJ400**

MEH225SS MEJ402S

ASME Tank Filler Valves MARSHALL EXCELSIOR

ASME Tank Filler Valves allow maximum product transfer with its manually operated open throat design. These valves have an integral high flow primary soft-seat back check and a manuallyoperated secondary shutoff valve for maximum protection against leaks. Because these valvesprovide a manually operated shutoff device, the need for a flow restricting fill check adapter has been eliminated.

• Allows 25 - 50% more product flow during filling operations

• Manual valve portion assures operator when valve is open or closed

• Removable key provided to prevent tampering

FEATURES: • Durable all brass construction for maximum weather and spark resistance• Constructed with a durable Nitrile O-ring

primary back check seal and reliable Teflon® packing for secondary manual valve seal

ASME TankFiller Valves

Item No. Filler ValveMNPT

Hose End M. AcmeConnection

Protective CapIncluded

AdditionalKeys

ME600-6 3/4” 1-3/4” Yes ME578-02ME600-10 1-1/4” 1-3/4” Yes ME578-02


Multipurpose Valves MARSHALL EXCELSIOR

Multipurpose Valves are intended for use as a high capacity filler valve with a manual shutoff device in LPG or NH3 containers. These valves can be equipped with either a soft seat back checkor excess flow feature that is internal to the container. The excess flow version can also be usedas a vapor equalizing valve typically found in NH3 applicators and nurse tank applications.

NOTE: For proper operation and performance of the excess flow feature the manual shutoff must be completely open and back seated.

* For NH3 flow rates multiply by .90 | ** For NH3 @ 100 PSI, Multiply by 1.6 | *** Brass accessories cannot be used for NH3 | **** Available for 45 GPMNH3 closing flow - e.i. ME670DEX/45

• Plated ductile iron body with 1/4” NPT auxillary plugged port

• All stainless steel internal construction for maximum corrosion resistance

• Supplied with ACME cap and chain assembly

FEATURES: • V-cup Teflon® packing stem seals• Rated 400 PSI/WOG• Removable data plate

Multipurpose Withdrawal Valves MARSHALL EXCELSIOR

* For NH3 flow rates multiply by .90 | ** Brass accessories cannot be used for NH3 service | *** Available for 45 GPM NH3 closing flow - e.i. ME671D-8/45

The ME671DIBC has an integrated back check (IBC) feature built into the lower portion of the seat disc assembly. This allows liquid pressure built upstream of the shut-off disc assembly toautomatically be relieved back to the container when line pressures exceed 10 - 25 PSI over container pressure. The (IBC) feature eliminates the need for hydrostatic relief valves to protectupstream piping or lines as well as greatly reducing product emissions and overall system safety.

ME671D-8

ME672D

ME670DEX

ME670DBC


205 206

J DJ

Double Check Fill Valves MARSHALL EXCELSIOR

Double Check Fill Valves are designed for DOT forklift, engine fuel and ASME residential tanks, these double check filler valves automatically open with pump pressure providing maximum product flow rates. Once flow ceases, both upper and lower check mechanisms close to prevent product loss from the container. The lower check serves as a secondary seat to limit product loss in the event that the primary upper seat fails to operate properly due to damage.

• Industry best flow rate• Resilient bonded main valve seal• Field repairable upper check seat

FEATURES: • Integral break away feature leaves primary

check intact in the event of truck roll away• Factory applied thread sealant

ME601-6

ME601-10

DOMESTIC TANK VALVES & ACCESSORIES

Item No. DescriptionFlow Rate LPG Accessories10 PSI 20 PSI Cap & Lanyard

ME601-61-3/4” M. Acme x 3/4” MNPT Double Fill Valve

with Cap & Lanyard11 24 ME578-02

ME601-10 1-3/4” M. Acme x 1-1/4” MNPT Double Fill Valve

with Cap & Lanyard22 36 ME578-02

Vapor Equalizing Valves MARSHALL EXCELSIOR

MEC Vapor Equalizing Valves can be purchased in single or double check versions. The single check version can be used to facilitate pressure equalization of lines or containers but must not be installed directly into the container. A properly sized excess flow device must first be installedinto container openings for compliance with NFPA Pamphlet #58. Double check versions consistof both an upper and lower check assembly. The upper check can be opened with vapor equalizing hose couplings equipped with projecting nozzle tips where the lower check is a normally open excess flow type. The lower excess flow check assembly automatically closes when flow out of the container exceeds its rated capacity. MEC double check vapor equalizingvalves feature a two piece body construction where the upper check can be repaired while in service with minimal leakage from the container.

• High flow construction• Resilient bonded main valve seal• Field repairable upper check seat

FEATURES: • Integral break away feature leaves primary

check intact in the event of a line pull away

Item No. Description Closing Flow

ME663Double Check Vapor Return Valve 3/4” MNPT x 1-1/4” M. ACME

with Plastic Cap4,000 SCFH/LPG

ME664 Single Check Vapor Return Valve 3/4” MNPT x 1-1/4” M. ACME

with Plastic CapN/A

ME664Single Check Valve

ME663Double Check Valve

DOMESTIC TANK VALVES & ACCESSORIESASME/ DOT Container Service Valves MARSHALL EXCELSIOR

• One piece forged brass body construction• Dual O-ring packing design• Easy to repair/replace bonnet assembly• Universal bonnet assembly

FEATURES: • Industry best fill flow rate• Factory applied thread sealant• Heavy duty replaceable zinc hand wheel

ASME/ DOT Container Service Valves are for use in vapor withdrawal service for ASME and DOT containers or as fuel line shutoff valves.

NOTE: These valves do not have an integral pressure relief valve. Use them with containers thathave a separate stand alone pressure relief valve sized to properly handle the container’s capacity.

ME9101C1

ME9101D-11.7

Item No. Description Dip Tube LengthME9101C1 3/4” MNPT X F. POL ASME/ DOT Service Valve (No Dip Tube) 4,000 SCFH/LPGME9101D-11.1 3/4” MNPT X F. POL ASME/ DOT Service Valve (with Dip Tube) 11.1” ME9101D-11.7 3/4” MNPT X F. POL ASME/ DOT Service Valve (with Dip Tube) 11.7”

ASME/ Tank Manifolding Service Valves MARSHALL EXCELSIOR


FEATURES: • Industry best fill flow rate• Factory applied thread sealant• Heavy duty replaceable zinc hand wheel• ASME Compliant

ASME Tank Manifolding Service Valves are intended for use in vapor withdrawal service for ASMEtanks where more than one vessel is installed. The internal excess flow device at the inlet of the shutoff valve provides excess flow protection in the event of a downstream line break.

NOTE: These valves do not incorporate an integral pressure relief valve or double check fill valveand are intended for use in containers that have a stand-alone pressure relief valve sized to properly handle the container’s capacity and a separate double check fill valve.

Item No. Description Excess Flow GPMME9101C5 3/4” MNPT X F. POL ASME/ DOT Container Service Valve 2.6 GPM

ME9101C1

ME9101C5Service Valve

500Gallon Tank

500Gallon Tank

ME1701BTee Fitting

ME1680 SeriesCopper Pigtail

ME9101C5Service Valve

MEGR-1622 Series First

Stage Regulator


207 208

J DJ

Multi-Service Vapor Valves for ASME Cylinders MARSHALL EXCELSIOR

• One piece forged brass body construction• Dual O-ring packing design• Easy to repair/replace bonnet assembly• Universal bonnet assembly• Heavy duty replaceable zinc hand wheel

FEATURES: • Plugged test port: ME662 Series - 1/4” FNPT ME665 Series - 1/8” FNPT• SC model features optional self-cleaning LE

thumb screw vent

The ME662 Series Multi-Service Valve is intended for use in vapor withdrawal service for ASMEcontainers or as fuel line shutoff valves in combination with an integral double check fill and vapor equalization valve.

The ME665 Series Multi-Service Valve is intended for use in vapor withdrawal service for ASMEcontainers or as fuel line shutoff valves in combination with an integral double check vapor equalization valve.

NOTE: ME662 and ME665 series valves do not incorporate an integral pressure relief valve ordouble check fill valve and are intended for use in containers that have a stand-alone pressurerelief valve sized to properly handle the container’s capacity and a separate double check fill valve.

Item No. Inlet Outlet Vent Type Diptube LengthME662 1-1/2” MNPT F. POL MEJ401

16”ME662SC 1-1/2” MNPT F. POL MEJ401SCME665 3/4” MNPT F. POL MEJ401

12”ME665SC 3/4” MNPT F. POL MEJ401SC


ME6621-1/2” MNPT

Multi-Service Valve

ME6653/4” MNPT

Multi-Service Valve


• One piece forged brass body construction• Integral fill valve• Easy to repair/replace bonnet assembly• Integral 375 PSI or 250 PSI relief valve• Heavy duty replaceable zinc hand wheel• 1/8” FNPT plugged test port

FEATURES: • Optional MEJ401SC self-cleaning LE fixed

liquid level vent screw• Liquid splash tube to prevent liquid in vapor

opening• F. POL vapor outlet with shutoff

Multi-Service Vapor Valves Indended for use in vapor withdrawal service for DOT or ASME containers ranging from 420 lbs. to 100 gallons LPG capacity as fuel line shutoff valves in combination with a fill and vapor relief valve. Ideal for on-site filling without interruption of service by combining all functions into a single 1” tank opening.

Item No. FillerConnection Inlet Inlet Inlet Inlet Inlet

MES-PVE2035AT-11.2 1-3/4” ACME 1” NGT F. POL 11.2” 375 —MES-PVE2035ATSC-11.2 1-3/4” ACME 1” NGT F. POL 11.2” 375 MEJ401SCMES-PVE2035AT-11.7 1-3/4” ACME 1” NGT F. POL 11.7” 375 —MES-PVE2035ATSC-11.7 1-3/4” ACME 1” NGT F. POL 11.7” 375 MEJ401SCMES-PVE2035AT-250-11.2 1-3/4” ACME 1” NGT F. POL 11.2” 250 —MES-PVE2035ATSC-250-11.2 1-3/4” ACME 1” NGT F. POL 11.2” 250 MEJ401SCMES-PVE2035AT-250-11.7 1-3/4” ACME 1” NGT F. POL 11.7” 250 —MES-PVE2035ATSC-250-11.7 1-3/4” ACME 1” NGT F. POL 11.7” 250 MEJ401SCMES-PVE2035AT-250-12.0 1-3/4” ACME 1” NGT F. POL 12.0” 250 —MES-PVE2035ATSC-250-12.0 1-3/4” ACME 1” NGT F. POL 12.0” 250 MEJ401SC

MES-PVE2035AT Multi-Service Valve

Multi-Service Vapor Valves MARSHALL EXCELSIOR


209 210

DJJ

Propane Liquid Capacity at Various Pressure Relief Valve

Item No.

Tank

Vapor Service

Filler

Fixed Liquid DT Differential Pressure (GPM) Flow Capacity (SCFM) Air

Connection

Connection

Connection

Level Gauge Length 10 20 50 100 PRV

MNPT

ACME

PSIG PSIG PSIG PSIG Setting UL

67.0805 3/4” POL (CGA 510) 1-3/4” Not Captive 10.6” 9 15 3 35 375 112367.0808 3/4” POL (CGA 510) 1-3/4” Not Captive 11.6” 9 15 23 35 375 112367.0812 3/4” POL (CGA 510) 1-3/4” Not Captive 6.0” 9 15 23 35 250 —67.0816 3/4” POL (CGA 510) 1-3/4” Not Captive 8.2” 9 15 23 35 375 112367.0821 3/4” POL (CGA 510) 1-3/4” Not Captive 10.2” 9 15 23 35 375 112367.1004 3/4” POL (CGA 510) 1-3/4” Not Captive 8.6” 9 15 23 35 375 1123

Item No. Tank Vapor Service Filler Fixed Liquid DT PRV

Connection Connection Connection Level Gauge Length Setting

67.1027 1” NPT POL (CGA 510) 1-3/4” ACME Not Captive 11.6” 375 PSIG


These Multi-Service Valves are multi-purpose and are suitable for 100 - 200 lb. DOT containers.The 67.0812 can also be used for a 60 gallon tank. They are ideal for on site filling of DOT cylinderup to 200 lb. LPG capacity without interrupting service.

• Includes a service valve, back check filler valve, fixed maximum liquid level gauge (specify DT length when ordering)

• New high discharge flow capacity pressure relief valve (1123 UL listing)

FEATURES: • Reduced filler valve chamber reduces the

waste of LPG during filling operation• Increased high filling capacity• Double O-ring replaceable stem

67.0805

420 Multivalve CAVAGNA GROUP

The 420 Multivalve is a multi purpose valve with double back check filler valve designed for use with 420 Ib. DOT containers.

• Includes a service valve, back check filler valve, fixed maximum liquid level gauge (specify DT length when ordering)

• Increased high filling capacity

FEATURES: • Reduced filler valve chamber reduces the

waste of LPG during filling operation• Double O-ring replaceable stem

67.1027

Multi-Service Valve CAVAGNA GROUP

• Epoxy coated ductile iron manifold• Durable o-ring service valve packing• Easy to repair/replace bonnet• Standard 1/4” NPT plugged gauge port

FEATURES: • Supplied with 30” diptube that can be cut

to length• Optional LE vent valve available

These Multi-Purpose Valves are designed for use on domestic ASME underground tanks that require a single opening except for a separate liquid withdrawal port.

Item No. ContainerConnection

FillingConnection

ServiceConnection

Size

ClosingFlow

GaugeFlange

Opening

PressureRelief Valve

Setting

ReliefValve

Capacity

FixedLiquid

Level TypeMES-PVE2098AT 2-1/2” FNPT 1-3/4” ACME F. POL 4000 CFH

@ 100 PSIGFits “Junior”

Size250 PSIG 1740

SCFM/airMEJ400C

MES-PVE2098ATSC 2-1/2” FNPT 1-3/4” ACME F. POL 250 PSIG MEJ400SCMES-PVE2098PT* 2-1/2” FNPT 1-3/4” ACME F. POL 4000 CFH

@ 100 PSIG”Fits “Junior”

Size250 PSIG 1740

SCFM/airMEJ400C

MES-PVE2098PTSC* 2-1/2” FNPT 1-3/4” ACME F. POL 250 PSIG MEJ400SC

Underground Tank Cluster Manifold MARSHALL EXCELSIOR

* Includes ME460 Liquid withdrawal valve packed seperately in carton.

MES-PVE2098AT

Underground Tank Cluster Valve Removal Tool MARSHALL EXCELSIOR

Item No. DescriptionMEP126 Underground Tank Cluster Valve Removal Tool

• Durable cast steel construction• Powder coat finish for maximum corrosion

protection• 3/4” drive

FEATURES:

The Underground Tank Cluster Valve Removal Tool is a universal design for convenient removalof underground tank cluster valves using a standard 3/4” drive socket wrench.

MEP126


211 212

DJJ


Item No.

Tank

Vapor Service

Filler DT

Differential Pressure (GPM) Flow Capacity (SCFM) Air


Connection

Length 10 25 50 75 PRV

UL ASME MNPT

ACME

PSIG PSIG PSIG PSIG Setting

67.0807 2-1/2” POL (CGA 510) 1-3/4” 36” 58 98 146 186 250 1918 1808

Item No.

Tank Vapor Service Vapor Line Gauge Fixed Liquid Fixed Level Gauge Wrench Connection Connection Connection Boss Level Gauge DT Length Hex Flat

67.0720 3/4” MNPT Female POL CGA 510 1-1/4” M.ACME 1/4” FNPT Yes 12” 1”


Item No.

Tank

Vapor Service

Filler DT

Differential Pressure (GPM) Flow Capacity (SCFM) Air


Connection

Length 10 25 50 75 PRV

UL ASME MNPT

ACME

PSIG PSIG PSIG PSIG Setting

67.0807 2-1/2” POL (CGA 510) 1-3/4” 36” 58 98 146 186 250 1918 1808

Item No. Container Line Wrench Propane Liquid Capacity at Various Differential Pressure (GPM)

Connection Connection Hex Flat 10 PSIG 20 PSIG 25 PSIG 30 PSIG 40 PSIG 50 PSIG 75 PSIG

66.1122 3/4” MNPT 1-3/4” M.ACME 1-3/4” 17 23 — 28 33 37 —66.1232 1-1/4” MNPT 1-3/4” M.ACME 1-3/4” 58 — 98 — — 146 18666.1134* 1-1/4”MNPT 1-3/4” M.ACME 1-3/4” 54 — 100 — — 148 190

Item No. Tank Filler Wrench Propane Liquid Capacity at Various Differential Pressure (GPM)

Connection Connection Hex Flat 10 PSIG 20 PSIG 25 PSIG 30 PSIG 40 PSIG 50 PSIG 75 PSIG

66.1261 1-1/4” NPT 1-3/4” 6 ACME Es. 46 mm 54 — 98 — — 146 18666.1262 1-1/4” NPT 1-3/4” 6 ACME Es. 46 mm 54 — 98 — — 146 186

Underground Multi-Service Valve CAVAGNA GROUP

The Underground Multi-Service Valve with Integrated Evacuation Valve is designed for use in a single opening ASME container with a riser of 2-1/2” MNPT. A separate opening is NOT required for a liquid withdrawal valve. Internal threads accommodate 2-1/2” MNPT riser pipe connection and a 3/4” FNPT connection for the filling valve opening.

• Double back check filler valve• Vapor equalizing valve with excess flow• Pressure relief valve with protective cap• Service valve with Cavagna quality handwheel system

FEATURES: • Plugged 1/4” FNPT gauge boss• Fixed liquid level gauge with 36” DT• Junior size float gauge flange opening• Double O-ring service valve; individual

replacement system

67.0807

DOMESTIC TANK VALVES & ACCESSORIESDOMESTIC TANK VALVES & ACCESSORIESMulti-Service Valve CAVAGNA GROUP

Multi-Service Valves are suitable for ASME tanks where a vapor service valve is required. Thisvalve has in the same body a service valve, a vapor withdrawal valve and a fixed level gauge.

• Improved stem seal• Redesigned Body Configuration• Convenient Level Gauge

FEATURES: • Gauge connection can be plugged or left

unplugged for installation of a pressure gauge• Ever-Seal is pre-applied on the inlet thread

67.0720

66.1232

Filler Valves 66.1122 and 66.1232 CAVAGNA GROUP

Underground Multi-Service Valve CAVAGNA GROUP

The Underground Multi-Service Valve with Integrated Evacuation Valve is designed for use ina single opening ASME container with a riser of 2-1/2” MNPT. A separate opening is NOT required for a liquid withdrawal valve. Internal threads accommodate 2-1/2” MNPT riser pipe connection and a 3/4” FNPT connection for the filling valve opening. Integrated liquidwithdrawal valve in the body of the multi-service valve provides easy access.

• Double back check filler valve• Vapor equalizing valve with excess flow• Service valve with Cavagna quality handwheel system

FEATURES: • Pressure relief valve with protective cap• Plugged 1/4” FNPT gauge boss• Fixed liquid level gauge with 36” DT

67.1020

Filler Valves 66.1261 and 66.1262 CAVAGNA GROUP

66.1261

• Double back-check filler valve with integral emergency shut-off ball valve• Soft seated upper back check• Metal-to-metal lower back check seat

FEATURES: • No need for filler hose adapter• Safe filler valve maintenance without tank evacuation• For use under or above ground

66.1122

66.1262

*Has a two-piece body


213 214

DJJ

Item No. Tank Connection Filler Connection Wrench Hex Flat

66.1206 3/4” MNPT 1-1/4” 5 ACME Es. 32 mm


66.1101 1-1/4” NPT 1-3/4” ACME 1-3/4”66.1106 1-1/4” NPT 1-3/4” ACME 1-3/4”66.1093 1-1/4” NPT 1-3/4” ACME 1-3/4”

Spare Part Item No. For Valve Item No.

30.0273, 10.5033,10.0204 66.1029, 66.112930.0274, 10.5036 66.103030.0274, 10.0203 66.112830.0276, 10.5037, 10.0205 66.1031, 66.113010.5032 66.1057, 66.1058, 66.1127, 66.113510.5056 66.116210.5056 66.102710.5038 66.0248


5605030021 UG WRENCH KIT - Valve Socket - 3/4” Drive, Fits Cavagna Multiservice Valves

for Asme Underground Propane Tank51C1140001 Valve Socket - 1/2” Drive, Fits Cavagna OPD Service Valves and Fork Lift Service Valves


66.1115 3/4” NPT 1-3/4” ACME 1-3/4” 66.1154 3/4” NPT 1-3/4” ACME 1-3/4”66.1157 3/4” NPT 1/2” SAE 11/16”66.1272 3/4” NPT 1/2” SAE 11/16”

DOMESTIC TANK VALVES & ACCESSORIESDOMESTIC TANK VALVES & ACCESSORIESVapor Equalization Valve CAVAGNA GROUP

The Vapor Equalization Valve is an upper back check valve and lower excess flow valve combined.

Filler Valves with Overfill Prevention Device CAVAGNA GROUP

The 66.1115, 66.1154, 66.1157 and 66.1272 are filler valves fitted with an OPD device are suitablefor direct filling automotive applications. These valves incorporate a standard 1-1/4” flat wrenching hex allowing easy installation from the top with a socket wrench.

NOTE: When ordering it is necessary to specify tank dimension, mount angle, and diameter to determine correct part number.

66.1115: Filler valve for vertical ASME and DOT containers. Suitable for a 300 liter horizontal tank or 119VG tank. They can be fitted to other tank sizes upon request.

66.1154: Filler valve with OPD for Automotive Application.

66.1157 and 66.1272: Remote Filler valve with OPD for Automotive Application.

66.1115

66.1154

66.1157

Filler Valves with Overfill Prevention Device CAVAGNA GROUP

The 66.1101, 66.1106, and 66.1093 are designed for horizontal and vertical LPG containers. All thevalves are equipped with an overfill prevention device. Always specify type of tank (horizontal or vertical), diameter of the tank and location of the filler valve in the flange of the tank.

66.1101: Suitable for underground tank. The extended body allows an easier refilling operation.

66.1106: Filler valve with high flow capacity suitable for above ground containers. Specify tank size when ordering.

66.1093: As with other valves that incorporate an OPD, this valve has, in addition, an extended filler valve with ball shut-off valve manually operated.

66.1106 66.1093

66.1101

Ug Wrench Kit and Valve Socket CAVAGNA GROUP

5605030021UG Wrench Kit

Plastic 10.5032, 10.5036, 10.5033, 10.5037 Vinyl 30.0274, 30.0273, 30.0276

Plastic10.5038

Plastic10.020310.020410.0205

66.1206

51C1140001Valve Socket

Tank Equipment Spare Parts - Rain Caps CAVAGNA GROUP

NOTE: Cavagna declines all responsibility for incorrect use or application. They recommend using original parts or to replace the whole valve.


215 216

J DJ

Item No. Size/Pounds Service Material Valve

CY414OPD 4-1/2 Vapor Steel OPD CY5OPD 5 Vapor Steel OPD CYAL6 6 Vapor Aluminum OPDCY10OPD 10-Tall Vapor Steel OPD CY11OPD 11-Short Vapor Steel OPD

CY15MC 15 Vapor Steel Mower Cylinder LH Connector,

Acme Fill, No GaugeCY20OPD 20 Vapor Steel OPDCY20SFG 20 Vapor Steel OPD and Sureflame GaugeCY20PL 20 Vapor Steel With Plumbers Pot Valve, OPDCYFL20 20 Liquid Steel Forklift w/Coupler and GaugeCY20HOR 20 Vapor Steel Horizontal w/Gauge OPDCY20BUF 20 Vapor Steel Verticle for Buffer Forklift w/Coupler and GaugeCYAL20BUF 20 Vapor Alum. Buffer Verticle Only Forklift w/Coupler and GaugeCY30OPD 30 Vapor Steel OPDCY30HOR 30 Vapor Steel Horizontal w/Gauge OPDCY33.5 33.5 Liquid Steel Forklift w/Coupler and GaugeCYAL33.5 33.5 Liquid Aluminum Forklift w/Coupler and GaugeCYAL33.5FV 33.5 Liquid Aluminum Forklift w/Coupler, Fill Valve and Gauge

CYAL33.5MC 33.5 Vapor Aluminum Mower Cylinder LH Connector,

Acme Fill, GaugeCY40OPD 40 Vapor Steel OPDCYAL40OPD 40 Vapor Aluminum OPDCY435 43.5 Liquid Steel Forklift w/CouplerCYAL435 43.5 Liquid Aluminum Forklift w/Coupler and GaugeCY50 50 Vapor Steel POLCY60 60 Vapor Steel POLCY100 100 Vapor Steel POLCY100L 100 Liquid Steel CGA555 HopaneCY100ASME 100 Vapor Steel POL and GaugeCY200DOT 200 Vapor Steel POL and GaugeCY200ASME 200 Vapor Steel POL and GaugeCY420DOT 420 Vapor Steel Multi-Valve

Item No. Size/Pounds Tank Type Valve

YSN201 20 lb. YSN301 30 lb. BBQ Propane

OPD and/or POL Valve Assembly YSN401 40 lb. YSN100 100 lb. BBQ/Home Heating

Item No. Size/Pounds Description

FLMKNG164LP 1 lb.

16.4 oz. Refillable Camping Tank FLMKNG141LP 14.1 oz. Industrial Camping Tank YSNEZF — E-Z Fill 1 lb. Refill Valve for Forklift Tank


YSN335 33 lb. Steel Forklift Tank

Item No. Size/Gallons Description

YSN293 29.3 ASME Vapor Draw Fuel Tanks

YSN141 14.1 Horizontal Mount with Brackets

YSN122 12.2


YSN201BT 20 lb. For Floor Burnishers, Vapor Draw, QuickFill valve, NO OPD

Cylinders MANCHESTER

420 lb. Cylinder

11 lb. Cylinder

5 lb. Cylinder

20 lb. CylinderTankfoot tank stablizer part number A91725 is available to assist the consumer in transporting 20, 30 and 40 pound cylinders.

100 lb. Cylinder

Portable Cylinders FLAME KING

20 lb. Cylinder 30 lb. Cylinder 40 lb. Cylinder 100 lb. Cylinder

1 Pound Refillable Propane Tanks FLAME KING

Forklift Tanks FLAME KING

ASME Vapor Draw Fuel Tanks FLAME KING

Buffer Tanks FLAME KING

CYLINDERS CYLINDERS


217 218

J DJ

• One piece forged brass body construction• Easy to repair/replace bonnet assembly• Integral 375 PSI relief valve (Propylene

service - 435 PSI)• Optional MEJ401SC self-cleaning LE fixed

liquid level vent screw

FEATURES: • Heavy duty replaceable zinc hand wheel• F. POL vapor outlet with shutoff• Available in vapor seal construction for

propylene service• Diptubes can be cut to length for specific

tank needs

Vapor Withdrawal Valves for Dot 100 LB. Cylinders are indended for use in vapor withdrawal service for DOT containers up to 100 lb. LPG capacity as fuel line shutoff valves in combinationwith a liquid fill and vapor relief valve.

Item No. Descriptions ContainerType

ReliefSTD PSI Vent Type Diptube

MES-PVE3250BC-312 Service Vapor 3/4” NGT X F. POL (705 SCFM) ASME 312 N/A N/AMES-PVE3250C-375 Service Vapor 3/4” NGT X F. POL DOT 375 N/A N/AMES-PVE3250CV-435 Propylene Service Vapor 3/4” NGT X F. POL DOT 435 N/A N/AMES-PVE3250CLG-375 Service Vapor 3/4” NGT X F. POL DOT 375 MEJ401 N/AMES-PVE3250CLGV-435 Propylene Service Vapor 3/4” NGT X F. POL DOT 435 MEJ401 N/AMES-PVE3250CLGSC-375 Service Vapor 3/4” NGT X F. POL DOT 375 MEJ401SC N/AMES-PVE3250CLG-10.6 Service Vapor 3/4” NGT X F. POL DOT 375 MEJ401 10.6”MES-PVE3250CLGV-10.6 Propylene Service Vapor 3/4” NGT X F. POL DOT 435 MEJ401 10.6”MES-PVE3250CLGSC-10.6 Service Vapor 3/4” NGT X F. POL DOT 375 MEJ401SC 10.6”MES-PVE3250CLG-11.6 Service Vapor 3/4” NGT X F. POL DOT 375 MEJ401 11.6”MES-PVE3250CLGV-11.6 Propylene Service Vapor 3/4” NGT X F. POL DOT 435 MEJ401 11.6”MES-PVE3250CLGSC-11.6 Service Vapor 3/4” NGT X F. POL DOT 375 MEJ401SC 11.6”

Vapor Withdrawal Valves for Dot 100 LB. Cylinders MARSHALL EXCELSIOR

MES-PVE3250CLG-10.6100 LB. Vapor Service Valve

Item No. Descriptions ContainerType

ReliefSTD PSI

WithdrawalTube Width Vent Type Diptube

MES-PVE3250CLM-375 Service Liquid 3/4” NGT X M. CGA555 DOT 375 1/4” MEJ401 N/AMES-PVE3250C-375 Service Liquid 3/4” NGT X M. CGA555 DOT 375 1/4” MEJ401SC N/AMES-PVE3250CV-435 Service Liquid 3/4” NGT X M. CGA555 DOT 435 1/4” MEJ401 11.6”MES-PVE3250CLMSC-11.6 Service Liquid 3/4” NGT X M. CGA555 DOT 375 1/4” MEJ401SC 11.6”

Liquid Withdrawal Valves for Dot 100 LB. Cylinders MARSHALL EXCELSIOR

• One piece forged brass body construction• Easy to repair/replace bonnet assembly• Integral 375 PSI relief valve• Optional MEJ401SC self-cleaning LE fixed

liquid level vent screw• Heavy duty replaceable zinc hand wheel

FEATURES: • Male CGA555 liquid outlet with shutoff• Integral 1.0 GPM/LPG excess flow valve• Diptubes can be cut to length for specific

tank needs

Liquid Withdrawal Valves for Dot 100 LB. Cylinders are indended for use in liquid withdrawal service for DOT containers up to 100 lb. LPG capacity as fuel line shutoff valves in combinationwith a liquid fi ll and vapor relief valve.

MES-PVE3250CLG-10.6100 LB. Vapor Service Valve

CYLINDER VALVES CYLINDER VALVES


219 220

J DJ

Item No.

Description Accessories Cap and Lanyard

ME602-8 1-3/4” M. Acme x 1/2” M. Flare Remote Fill Valve w/Cap and Lanyard ME601-902

CYLINDER VALVES

• One piece forged brass body construction• Easy to repair/replace bonnet assembly• Integral 375 PSI relief valve• Optional MEJ401SC self-cleaning LE fixed

liquid level vent screw• Heavy duty replaceable zinc hand wheel

FEATURES: • F. POL vapor outlet with shutoff• Diptubes can be cut to length for specific

tank needs• Liquid splash tube to prevent liquid in vapor

opening

Multi-Service Vapor Valves for Dot 100 LB. Cylinders are intended for use in vapor withdrawal service for DOT containers up to 200 lb. LPG capacity as fuel line shutoff valves in combinationwith a fill and vapor relief valve. Ideal for on-site filling without interruption of service bycombining all functions into a single 3/4” NPT tank opening.

Item No. Fill Connection Inlet Outlet Vent Type Diptube Length Relief STD PSIMES-PVE2030BC-10.6 1-3/4” ACME 3/4” NGT

F. POLw/ Shutoff

— 10.6” 375MES-PVE2030BCSC-10.6 1-3/4” ACME 3/4” NGT MEJ401SC 10.6” 375MES-PVE2030BC-11.2 1-3/4” ACME 3/4” NGT — 11.2” 375MES-PVE2030BCSC-11.2 1-3/4” ACME 3/4” NGT MEJ401SC 11.2” 375MES-PVE2030BC-11.6 1-3/4” ACME 3/4” NGT — 11.6” 375MES-PVE2030BCSC-11.6 1-3/4” ACME 3/4” NGT MEJ401SC 11.6” 375MES-PVE2030BC-8.6 1-3/4” ACME 3/4” NGT — 8.6” 375MES-PVE2030BCSC-8.6 1-3/4” ACME 3/4” NGT MEJ401SC 8.6” 375

Multi-Service Vapor Valves for Dot 200 LB. Cylinders MARSHALL EXCELSIOR

MES-PVE2030BCMulti-Service Valve

CYLINDER VALVESForklift Cylinder and Engine Fuel Valves MARSHALL EXCELSIOR

These Cylinder Valves are intended for vapor or liquid withdrawal service on DOT forklift or engine fuel containers. Two closing flow rates are offered - 1.5 GPM for medium to light duty vehicles and 2.6 GPM for those with greater fuel demands.

NOTE: These valves do not incorporate an integral pressure relief valve and are intended for usein containers that have a separate pressure relief valve to adequately handle the container’s capacity. Each of these valves incorporate an excess flow valve at the tanks inlet end to preventexcessive product loss in the event of a downstream fuel line failure. For the excess flow deviceto perform properly the service valve must be in the full open and back seated position.


FEATURES: • Industry best fill flow rate• Factory applied thread sealant• Replaceable, heavy duty zinc hand wheel

featuring a universal design

ME9101P5H

Engine Fuel Remote Fill Valve MARSHALL EXCELSIOR

Engine Fuel Remote Fill Valves are specifically designed for remote filling applications where a standard tank type filler valve is not practical. Perfectly suited for motor fuel applications orother hard to reach remote tank applications. This single check fill valve is designed to providemaximum product fill rates along with an automatic shutoff once product flow ceases.

• Single check design allows maximum product flow rate• Integral break away feature leaves check

valve intact in the event of a vehicle roll away during filling

FEATURES: • Resilient bonded main valve seal• Rear bulkhead mounting with quarter panel

jam nut and lock washer• Single piece main valve body for maximum

strength and durability

ME602-8

Item No. Description Excess Flow GPMME9101P5

3/4” MNPT X 3/8” MNPT Forklift Service Valve1.6 GPM

ME9101P5H 2.6 GPMME9101H4

3/4” MNPT X 3/8” M. Flare Motor Fuel Service Valve1.6 GPM

ME9101H6 2.6 GPM

MEP125

This heavy duty designedwrench features a 1/2” drive socket extension for removing

and installing motor fuelcylinder valves.


221 222

DJJ

Item No. Container Connection Outlet Connection Normal Application Excess Flow Closing

80.2063 3/8” SAE Flare (70) ASME Motor Fuel 3.3 GPM 80.2062

3/4” M.NGT 3/8” SAE Flare (90) ASME Motor Fuel 3.3 GPM

80.2146 POL (CGA 510) ASME Motor Fuel 1.5 GPM 80.2064 3/8” 18 NPT DOT Fork Lift 2.6 GPM 73.0001 3/4” - 14 NPT 5/8” UNF RV - Automotive 1.4 GPM

Item No. Inlet Outlet Application

80.8190 M 34 3/8-18 NPT Dot Fork Lift

Item No. Container Outlet U.L. Closing Flow Wrench

Connection Connection (Propane) Hex Flat

69.0010 3/4” MNPT 5/8” FNPT 20 GPM 1-15/16”66.1109 1-5/8” UNF 3/4” UNF — —69.0109 1-1/4” NPT 3/4” NPT — 1-3/4”

Item No. Tank Vapor Service Fixed Liquid Fixed Level Connection Connection Level Gauge Gauge DT Length

80.3135 Not captive

11.1”80.3144 5.8”80.1199

3/4” NGT POL CGA 510 — —

80.3149 11.0”80.3190 Not captive 10.0”80.3191 10.63”

CYLINDER VALVESCYLINDER VALVESService Valves for DOT Fork Lift and ASME Motor Fuel Containers CAVAGNA GROUP

These Service Valves are designed for vapor or liquid withdrawal service on DOT fork lift truck containers (80-2064) and ASME containers. All these valves are equipped with an excess flowlimiter with different settings. Since these valves do not have an integrated pressure relief valve,they may only be used as an accessory valve on containers that have an independent PRV suitable for that container’s capacity.

All these valves are supplied with pre-applied sealant on the inlets. The 80.2064 has also pre-applied sealant on the outlet. Two O-rings form the stem seal for improved resistance to leakage due to dirt or temperature extremes.

• Tamper proof design• Sturdy quality handwheel brass handle• Static seat disc eliminates abrasive wear

on the disc improving service life

FEATURES: • Recessed excess flow valve reduces the

possibility of mechanical damage or fouling from excess pipe compound

80.206380.206480.2146

73.0001

Fork Lift DOT Multivalve CAVAGNA GROUP

Cavagna Group’s 80.8190 is designed specifically as a “One-Hole” solution for composite LPG cylinders in DOT fork lift truck service. This “One-Hole” solution has fewer points for potential leaks. This valve has multi-functions acting as a PRD and Excess Flow Valve.Its straight threads reduce torque force into the composite cylinder wall.

80.8190

CYLINDER VALVESCYLINDER VALVESLiquid Withdrawal Valves with Excess Flow CAVAGNA GROUP

Withdrawal Valve 69.0010 is designed to liquid evacuation prior to moving the tank. This valve can also be used on permanent installations equipped with an excess flow limiter. Designedaccording to the latest UL standard.

Withdrawal Valve 69.0109 performs as an excess flow valve.

Adapter 66.1109 is to be used with a 69.0010 liquid withdrawal valve. It is fully compatible with the new evacuation valves on the market.

Service Valves for ASME, DOT Containers, & Fuel Line Application CAVAGNA GROUP

Service Valve 80.3135 was created especially for vapor withdrawal service on ASME and DOTcontainers. Since this valve has no integral pressure relief valve, it may only be used as anaccessory valve on containers that have an independent pressure relief valve sufficient for thatcontainer’s capacity. This valve can also be used as a service valve on a 420 lb. vertical tank or a 300 liter horizontal tank. This valve also incorporates a fixed liquid level gauge. Specify DT length when ordering. Valve 80.1199 is an open-close valve with POL outlet and is designed for vapor withdrawal only.

• Double O-ring stem seal• Sturdy quality handwheel brass handle

FEATURES:

• Static seat disc eliminates abrasive wear on the disc improving service life

69.0010

69.0109

66.1109

80.3135

80.1199


223 224

DJJ

Item No.

Cylinder Outlet Normal Liquid DT Relief UL Rated Discharge Connection Connection Application Level Gauge Length Setting Flow Capacity (SCFM)

80.6032 Female DOT cylinder up to 100 lb. Yes 10.2”

76580.5016 3/4” NGT POL Service valve on DOT cylinder Yes 375

—80.5064 (CGA 510) DOT cylinder up to 100 lb. No —

Item No. Cylinder Container Outlet Relief Dip

Capacity Connection Connection Setting Tube

82.8014 20 lb. 4.0”82.8012 30 lb. 3/4” 14 NGT Type 1 ACME and POL 375 PSIG 4.7”82.8013 40 lb. 6.4”

Item No. Size *Multi-Valve

ME312-5MV 3-1/8” YesME350 3-1/2” NoME350MV 3-1/2” Yes

Item No. Thread Style

MEP121 Male POL POLMEP122 1-5/16” Female Acme Type I (QCC)/ OPD

LPG Valve Type 1

Overfill Prevention Device

• Rapidly purges and fills; over one million BTU withdrawal capacity

• Tri-lobular one-piece forged aluminum handwheel• Leak resistance double O-ring stem seal• Pre-applied Ever-Seal sealant

FEATURES: • O-ring check valve seat opens only with

positive seal• Upward spray filling eliminates premature shutoffs• Steel safety cage surrounding critical welds provides additional protection to components

CYLINDER VALVESService Valves for DOT Cylinders CAVAGNA GROUP

Service Valve 80.5016 is a DOT cylinder valve for vapor withdrawal up to 100 lb. LPG capacity. Specify dip-tube length when ordering.

Service Valve 80.6032 is a heavy duty POL valve with pressure relief valve for 200 lb. propane cylinders. Different DT length.

Type 1 Acme Cylinder Valve with Overfill Prevention Device (OPD) CAVAGNA GROUP

Type 1 Acme Cylinder Valves are intended for DOT cylinders up to 40 pounds LPG capacity (96pounds water capacity). This valve has a vapor service outlet, relief valve, captive fixed liquid level gauge, and an overfill prevention device (OPD).

80.603280.5016

* Multi-valve style features cut-out in thread to provide clearance for assembly over a container valve.

ME350MVME350

Designed to remove or install Type I (QCC)/OPD cylinder valves or POL service valves without damage to the valve base.

Cylinder Valve Wrenches MARSHALL EXCELSIOR

MEP122

MEP121

Steel propane cylinder collars are designed to protect the valve installed on a cylinder. An automotive grade powder coat finish provides maximum corrosion resistance.

WARNING: It is illegal to fill a tank without a protective collar. Without a protective collar serious damage can occur to the cylinder valve which can lead to catastrophic events such as the tank becoming a dangerous projectile, an explosion and/or fire causing property damage, or personal injury or death.

Cylinder Collars MARSHALL EXCELSIOR

CYLINDER VALVES ACCESSORIES


225 226

KK


A16 Custom Imprinted DOT Cylinder Labels

Minimum Order 3500AA16 DOT Cylinder Labels - Minimum Order 100AA16ROLL DOT Cylinder Labels 500 Per Roll

2N1 For All Portable Cylinders - 500 Per Roll

DOT 1075 / Warning ANSI / MFPA Pamphlet 58V56R 3 in 1 Hazardous Material Label, 10 x 3-1/2”SP53R Warning Label, 3 Valves Black on YellowP-101 Water Capacity ChartP102 Notice for Your SafetyP-206 Cylinder Filling Instructions (ASME/DOT) - PolyV206 Cylinder Filling Instructions (ASME/DOT) - VinylV14 Cylinder Exchange Check List - VinylC37 Cylinder Exchange Check List - CoroplastP111 OPD Sign - “Does your valve look like this …”P-114 OPD Retrofit Guide

PMICH No Smoking - No Open Flame ..

Warning: Filling the following…

V128 This Container is NOT Equipped with an OPD

(For Horizontal Cylinders)RIN LABEL RIN DOT Cylinder Decal Label 50 Per RollCUSTOM RIN RIN DOT Cylinder Decal Label 500 Per Roll


M1075 Magnetic Diamond Placard 1075-2 LPG

P1075 Plastic Placard Diamond 1075-2 LPG,

Works with MPH69 HolderS1075 Scotchlite Reflective 1075 DecalsV1075 Vinyl Placard Diamond Decal 1075-2 LPGMPH69 Placard HolderCG126FO Flip Placard Assembly Metal Frame81-CLIP Stainless Steel Clip for CG126FO Metal PlacardV83 Shipping Paper 1075-2 One TruckV83-CYL Shipping Paper for Cylinder TruckV83-TANK Shipping Paper One Storage TankVDOT “Operating Under 49 CFR 171.5” White on Black DecalS22B 4” x 36” We Stop at all Railroad (RR) Crossings Decal S22C 8” x 12” We Stop at all Railroad (RR) Crossings DecalS500 3” x 5” Black Diamond “PROPANE“ DecalHZ116 OSHA Commercial Cylinder Decal 2-4-0 PROPANESMV7 Slow Moving Vehicle DecalV92 Liquid/Clutch/PTO/Bypass DecalV8 Vapor/Relief/Liquid DecalV45 Valve ID Label Set 10” x 10” DecalV65 QT DecalV66 NQT DecalV31 HM-183 Annual Inspection Decal KitV32 HM 183 5 Yr. Inspection Decal KitV33 Number Sheet Only for V31 and V32 DecalV90-5 “Liquid” Five Per Sheet 1” x 4” DecalV91-5 “Vapor” Five Per Sheet 1” x 4” Vinyl DecalV58C LPG Octane Label 2-1/2” x 3” DecalV75-20 Container Shutoff DecalV75-20 Tag Container Shut Off Warning Tag

Decals and Signs

AA16/AA16 ROLL

C37

SP53R

P-101

P102

S500

Decals and Signs

MPH69

V8

V-83ONE TRUCK LOAD

V83-TANKONE STORAGE TANK

V65 V66

S22C

M1075, P1075,S1075, V1075

CG126FO

V45

V90-5 V91-5 V92

V56R

P-206/V206 P114

2N1

SMV7

HZ116

V32

V31

V83-CYLNO OF CYLINDERS

S22B

SAFETY EQUIPMENT SAFETY EQUIPMENT


227 228

KK


M97A 2’ x 4’ Aluminum Single Faced

“PROPANE FILLING STATION”

M97AD 2’ x 4’ Aluminum Double Faced

“PROPANE FILLING STATION”

M97AX 2’ x 4’ Aluminum Single Faced

“PROPANE CYLINDERS EXCHANGED”

M97AXD 2’ x 4’ Aluminum Double Faced

“PROPANE CYLINDERS EXCHANGED”M97FR 2’ x 4’ Frame for Metal SignsV24A 6” Flammable DecalV24BB 3” Flammable DecalV24C 2” Flammable DecalV17B 4” Flammable Gas Vinyl DecalV17C 2” Flammable Gas Vinyl Decal

V52 11” Flammable Gas Diamond Decal Red with

White Letters, Class 2

V52S 4” Flammable Gas Diamond Decal Red with

White Letters, Class 2V28A Propane 6” Letters DecalV28B Propane 4” Letters DecalV28BB Propane 3” Letters DecalV28C Propane 2” Letters DecalV288BB Propane Gas 3” Letters DecalV39B 12” x 18” No Smoking or Open Flames 25’ DecalM39B 12” x 18” Metal No Smoking Within 25 ft.V26A 12” x 18” No Smoking/Shut Off Motor DecalV23A 6” No Smoking DecalV23BB 3” No Smoking DecalV23B 4” No Smoking DecalM23BB 3” No Smoking on MetalV23C 2” No Smoking DecalV21 Concerned for Your Safety Cylinder Filling DecalV121 Port Cylinder Fill Instructions DecalP13 Emergency Contact # ‘s 18” x 24”


P148 Plastic Sign Liquid Valve Emergency Shut Off

Pull to Close 10” x 12”

P149 Plastic Sign Liquid Valve Emergency Shut Off

Push to Close 10” x 12”V81 Vinyl Sign Emergency Shut Off Pull to Close 10” x 12”V126 Vinyl Decal Emergency Shut Off Pull to Close 5” X 6”V129 Vinyl Decal Emergency Shut Off Push to Close 5” x 6”V302BB 3” Liquid Petroleum Gas Vinyl DecalV302C 2” Liquid Petroleum Gas Vinyl DecalV2A 2” Anhydrous Ammonia Vinyl DecalV5 4” Anhydrous Ammonia (Straight) DecalV5A 4” Anhydrous Ammonia (Curved) DecalV2B 2” Vinyl Inhalation Hazard Decal

V1005 NH3 Placard Diamond Vinyl Decal Green Stick on

Diamond 1005V41 2” Liquified - Green Letters Decal704-1 2-4-0 OSHA Diamond 7-1/2” X 7-1/2” Propane Decal704-3 2-4-0 OSHA Diamond 15” X 15” Propane DecalV30 Tank Filling Instructions 15” X 22“ Motor Fuel Decal7282Q Methanol Warning Decal 3” x 5”V1203 UN 1203 Gasoline Diamond Decal PlacardV50 3N1 DOT Decal for Ragasco Forklift Cylinder

SAFETY EQUIPMENT SAFETY EQUIPMENTDecals and Signs Decals and Signs

V24A / V24BB / V24C

V17B / V17C

V28A / V28B / V28BB / V28C

V288BB

V23A / V23BB / V23B M23BB / V23C

V26A

V39B/M39B

V21 C37

M97A M97AD M97AX M97AXD V52

V129

704-1 / 704-3

V81 / V126 P148

P149

V5

V302BB / V302C

V50

V2B

V2A

V1005

V41


229 230

KK

Item No. Material Style Inlet (MNPT) Outlet (FNPT)

ME202 Brass #54 Orifice ME202SS Stainless Steel #54 Orifice 1/4” 1/4”ME204 Brass Sintered Metal Filter Disc

Item No. Brass Steel*

Four Barb Seven Barb

Four Four Barb Hose

Threads Low High Barb

with 3/64” I.D. Pressure Pressure Orifice Hole

ME4631 — — — 1/4” 1/8” FNPTME4632 ME5632 — — 1/4” 1/4” FNPTME4633 ME5633 — — 1/4” 3/8” FNPTME4652 — — — 3/8” 1/4” FNPTME4653 ME5653 — — 3/8” 3/8” FNPTME4654 — — — 3/8” 1/2” FNPTME4231 ME5231 — — 1/4” 1/8” MNPTME4232 ME5232 — — 1/4” 1/4” MNPTME4233 ME5233 — — 1/4” 3/8” MNPT — — A6132 A6133 3/8” 1/8” MNPTME4252 — A1132 A1133 3/8” 1/4” MNPTME4253 ME5253 — — 3/8” 3/8” MNPTME4254 — — — 3/8” 1/2” MNPT — — A6138 A6139 1/2” 1/8” MNPT — — A1138 A1139 1/2” 1/4” MNPTME4273 — — — 1/2” 3/8” MNPTME4274 ME5274 — — 1/2” 1/2” MNPTME4293 — — — 5/8” 3/8” MNPTME4835 ME5835 — — 1/4” 3/8” Male FlareME4855 — — — 3/8” 3/8” Male FlareME4857 — — — 3/8” 1/2” Male Flare — ME5133 — — 1/4” 1/4” Male Inverted FlareME4333 — — — 1/4” 1/4” Female Flare Swivel

ME43352 ME53345, 6

— — 1/4” 3/8” Female Flare Swivel ME5335

ME43553 ME53366 — — 3/8” 3/8” Female Flare Swivel

ME5355ME4357 ME5357 — — 3/8” 1/2” Female Flare SwivelME43774 ME5377 — — 1/2” 1/2” Female Flare Swivel

Hose Ferrules Item No. I.D. OAL

ME7323 .525” ME7324 .531” ME7325 .562” 1” ME7326 .593” ME7327 .625”

Hose Ferrules Item No. I.D. OAL

ME7329 .687” ME7330 .718” ME7331 .750” 1” ME7332 .781” ME7333 .812”

Hose Menders Item No. Hose I.D.

ME27C 1/4” x 1/4” ME27E 3/8” x 3/8”


ME-LD02 2 oz Marshall Excelsior Leak Detector Spray BottleME-LD1 8 oz Marshall Excelsior Leak Detector Cap and DauberME-LD16 16 oz Marshall Excelsior Leak Detector Cap and BrushME-LD2 1 gal Marshall Excelsior Leak DetectorWIN EMPTY 8OZ 8 oz Sherlock 5-Second Leak Detector Cap and DauberWIN EMPTY PT 16 oz Sherlock 5-Second Leak Detector Spray Bottle WIN GALLON LD 1 gal Sherlock 5-Second Leak Detector


Snubbers are designed for a pressure gauge to be threaded into their outlet. The snubber will reduce pressure fluctuations that can over pressurize or damage the gauge while maintaining a quick response time and a steady reading.

Pressure Gauge Snubbers MARSHALL EXCELSIOR

ME202SS

ME204

*Rated for LP-Gas and NH3 | 2 ME4335-1 (barb only); ME4335-2 (nut only) | 3 ME4355-1 (barb only); ME4335-2

(nut only) | 4 ME4377-1 (barb only); ME4377-2 (nut only) | 5 ME5334-1 (barb only) | 6 Forged Nut

ME4652

ME5632

Hose Barbs MARSHALL EXCELSIOR

ME5233

ME4252

A1132

ME4835

ME5133

ME5335

Hose Ferrules & Hose Menders MARSHALL EXCELSIOR

Low Temperature Leak Detector is for all pressurized gases and designed to detect joint leaks within 5 seconds of proper application at temperatures down to -40° F.

Low Temperature Leak Detector

ME-LD02

ME-LD2

ME27C

ME27EME7327

ME-LD16

Winton Gallon

Winton Empty

Win Empty 16 oz.


231 232

KK

Item No. Inlet Outlet PSIG Factory Installed Vent Valve

MEJ600 Male Hard Nose POL Female POL 0 - 300 NoMEJ601 Male Hard Nose POL Female POL 0 - 300 YesMEJ601-WOG* Male Hard Nose POL Female POL — Yes

Item No.

Kit with Gauge and Gauge and Gauge and Adjustable Manometer

Case

Hose Hose Barb 1/4” MNPT Gauge Adapter Only Connection Connection

ME60P-2 ME60P-5 — ME60-2 Yes ME1328 (3/8” OD) ME1331 (1/2” OD) ME50P-2 ME50P-5 ME50-2 ME50-2-01 No ME1332 (5/8” OD)

Item No. Connection ConnectionMETL051 5/16”-32 Male / 1/8” MNPT / 1/2” MNPT Standard test hose fitting/1/8” MNPT

METL052 5/16”-32 Male / 1/8” MNPT / 1/4” MNPT Standard test hose fitting/1/8” MNPT

Item No. Inlet PSIG

MEJ610/15 0 - 15MEJ610/30

3/4” FNPT 0 - 30

MEJ610/60 0 - 60MEJ610/100 0 - 100

Item No. Inlet Outlet PSIG Factory Installed Vent ValveMEJ602* — MEJ603LP 1/4” MNPT 1/4” FNPT 0 - 15 YesMEJ603HP 0 - 100

High Pressure Test Blocks test high pressure lines downstream of the container valve forsystem leaks. The optional bleeder valve enables the line pressure to be adjusted to the desiredtest pressure.

* Without gauge

MEJ600

SAFETY EQUIPMENT SAFETY EQUIPMENTHigh Pressure Test Blocks MARSHALL EXCELSIOR

MEJ601

Low Pressure Test Kits MARSHALL EXCELSIOR

Low Pressure Test Kits are used to check for gas leaks by verifying the line pressure of anappliance. Each kit includes a case, gauge, and rubber hose with a bell on the end.

• Capacity 0 - 35” water column• Three foot rubber hose with bell

TEST KIT FEATURES: • Adjustable gauge models can be reset to

zero with provided screwdriver

Serviceman’s Friend MARSHALL EXCELSIOR

METL051 and METL052 Adapters eliminate the hassle of carrying numerous bushing and fittingsto job sites. These adapters have three threads on one end with a hose barb and an 1/8” MNPTon the other end. A hose can easily be attached to either end and can be connected to a manometer or other flow meters to check line pressure on an appliance.

ME50-2

ME50P-5

ME60P-2ME50P-2

METL051

ME1332

MEJ610/30

Low Pressure Test Block MARSHALL EXCELSIOR

Marshall’s Test Blocks are designed to test low pressure lines for system leaks. The factory installed check valve allows the line to be pressurized and adjusted to the desired test pressure.

Pressure Test Gauge MARSHALL EXCELSIOR

* Without gauge

• Reliable method to test high and low pressure tap installations• Provides an effective method to bleed

vapor for pressure equalization and more accurate gauge readings

FEATURES: • Allows for an effective method to bleed

vapor from the testing equipment prior to disconnect

• High quality liquid filled pressure gaugeMEJ603HP


233 234

K K


TG30A Single Point Gauge Assembly - 30 PSIG GaugeTG30B Single Point Gauge Assembly - 30 PSIG GaugeKVA Gauge Assembly with 30 PSI Gauge and Built-In Regulator with Type A ValvesKVB Gauge Assembly with 30 PSI Gauge and Built-In Regulator with Type B ValvesSKVA Gauge Assembly with 35” W.C. Gauge and Built-In Regulator with Type A ValvesSKVB Gauge Assembly with 35” W.C. Gauge and Built-In Regulator with Type B Valves


VA1 1/8 MNPT ValveVA2 1/4 MNPT ValveVB1 1/8 MNPT ValveVB2 1/4 MNPT ValveHSA Hose Swivel Connector to Type VA ValveHSB Hose Swivel Connector to type VB Valve


QTG127A Dual Gauge Leak Check Kit - 30 and 300 PSI Gauges with Type A ValvesQTG128B Dual Gauge Leak Check Kit - 30 and 300 PSI Gauges with Type B ValvesQTG16A Dual Gauge Leak Check Kit - 30 PSI and 35” Water Column Gauges w/ Type A ValvesQTG16B Dual Gauge Leak Check Kit - 30 PSI and 35” Water Column Gauges w/ Type B ValvesSQTG4A Four Gauge Kits (Includes 5, 30, and 300 PSI Gauges) with Type A ValvesSQTG4B Four Gauge Kits (Includes 5, 30, and 300 PSI Gauges) with Type B Valves

Gauge Assemblies

Koch & Associates Gauge Assemblies TG and QTG Series are intended for bobtail drivers whoare trained to conduct out of gas leak check tests. The SQTG Series gauge assembly give the service technician what is needed to test pressure regulators for flow set point and lock-up pressure in addition to leak check testing.

NOTE: Model number suffix A or B designates which type of pressure tap valve will be used. The A designates the type VA valve (Schrader) and B designates the type VB valve (1/4 flare).

TG30A and TG30B Single Point Gauge Assemblies come with a 30 PSIG gauge and are used forleak check tests at intermediate pressure at outlet of first stage regulator or inlet to second stage regulator.

KVA and KVB Multi Point Kits are gauge assemblies with 30 PSI gauges and built in regulators that limit the pressure to the gauge to 12 PSI so the gauge can be used for leak check testing at intermediate pressure taps or at tank pressure using the high pressure test block. Kit includes twelve 1/8 NPT valves and six 1/4 NPT pressure tap valves.

SKVA and SKVB Universal Kits are gauge assemblies with 35” W.C. gauges and built-inregulators that limit the pressure to the gauge to 22” W.C. so the gauge can be used for leak check testing anywhere in the system. It can also be used to measure second stage, low pressure regulator set point and lock up pressure or appliance manifold pressure. Kit includes twelve 1/8 npt and six 1/4 npt pressure tap valves.

TG30A or TG30B

SKVA orSKVB

Gauge Assembly Valves

VB2

HAS/HSB

SAFETY EQUIPMENT

Koch & Associates’s Test Kit KV Series is intended for bobtail drivers who are trained to conductout of gas leak check tests. The SKV series test kit is intended for service technicians, which gives them the ability to test pressure regulators for flow set point and lock-up pressure in addition to leak check testing.

NOTE: Model number suffix A or B designates which type of pressure tap valve will be used. The A designates the type VA valve (Schrader) and B designates the type VB valve (1/4 flare).

QTG127A and QTG128B Dual Gauge Kits are used for leak check tests at intermediate pressure using the 30 PSI gauge and also leak check tests at tank pressure using the 300 PSI gauge and the high pressure test block supplied with the kit. The hose assembly connection to the system pressure tap valve incorporates a quick disconnect fitting to either pressure gauge. Kit includes six pressure tap valves, either type A or type B depending on which kit is specified.

QTG16A and QTG16B Dual Gauge Kits are used for leak check test at intermediate pressure using the 30 PSI gauge and testing first stage regulator. The 35” water column gauge is used for testing low pressure second stage regulator set point and lock up pressure.

SQTG4A and SQTG4B Four Gauge Kits include a 30 PSI gauge, a 300 PSI gauge, a 5 PSI gauge,a 35” water column gauge, and a high pressure test block plus six pressure tape valves either type A or type B depending on which kit is specified. The hose quick disconnect allows for attachment of any one of the gauges. A leak check pressure tap valve can be anywhere in the system with the proper gauge attached for leak check testing. This kit also allows the service technician to test all pressure regulators, including the first stage, using the 30 PSI gauge, a 2 PSI regulator using the 5 PSI gauge, and low pressure 11’ W.C. regulators orappliance manifold pressure using the 35” WC gauge.

Leak Check and Regulator Testing Kits

QTG127A or QTG128B

SQTG4A or SQTG4B

SAFETY EQUIPMENT

KVB

ME-SKVA or ME-SKVB

ME-QTG16B

VA1

VA1/VA2

VB1


235 236

KK

Item No. With Without Connection Connection Port Hole with

Plug Plug #54 Orifice

ME295 ME295-1 Male Hard Nose POL Female POL 1/8” FNPT ME295SN ME295SN-1 Male Soft Nose POL Female POL 1/8” FNPT ME296 ME296-1 1/4” MNPT 1/4” FNPT 1/8” FNPT ME297 ME297-1 3/8” MNPT 3/8” FNPT 1/8” FNPT ME298 ME298-1 1/2” MNPT 1/2” FNPT 1/8” FNPT — MEJ595 1/2” MNPT 1/2” FNPT 1/4” FNPT (No Orifice)

ME299 ME299-1 3/4” MNPT 3/4” FNPT 1/8” FNPT

Item No. Connection Connection Thread Sealant

MEJ607-02 1/4” MNPT NoMEJ608-02 1/8” MNPT 5/16” - 32 Male NoMEJ608B-02 1/8” MNPT Yes

Item No. Connection Connection Description

MEJ604 1/4” FNPT 1/8” MNPT Extension

Item No. (1/4” Hose ID) Connection Connection Thread Sealant

MER432-6 1/8” MNPT 1/4” FNPT

6”MER432-12 12”


ME10BTK-1-01 1/8” FNPT 5/16”-32 Female


1222-16 U-Tube ManometerA126 3/4 oz. Replacement Green Dye1222-16-D Oil Filled U-Tube ManometerA101 3/4 oz. Red Gauge OilA102 4 oz. Red Gauge OilA201 3’ Tubing with Replacement Bell EndA319 Flexible Red PVC Connector for 1222 Manometer


1212 Slack Tube ManometerA401 1212 CaseA126 3/4 oz. Green Replacement DyeA201 3’ Tubing with Replacement Bell End1D4976 Rubber Bell Adapter1212 KIT Adapter KitA339 Brass Adapter 1/8” MPT x 1/8” Barb


EM151 Electric Manometer with Hose

Pressure Test Accessories MARSHALL EXCELSIOR

MEJ608B-02 Check Valve allows the line to be pressurized and adjusted to the desired pressure through the same valve.

NOTE: To help eliminate valve failure, the valve cap should remain on the valve when line is notbeing pressurized or adjusted. Any dirt, debris, water or other contaminants can potentially jamthe valve or compromise the sealing surface causing the valve to leak.

Pressure Test Accessories MARSHALL EXCELSIOR

MEJ595

ME296-1

MEJ604

MEJ608B-02

Marshall’s Accessories provide an inexpensive way to permanently install a pressure tapupstream or downstream from the first stage regulator. The #54 orifice port provides controlledline pressure for more accurate readings and protects test equipment from pressure spikes while allowing easy installation of pressure test monitoring devices.

Flexible Rubber Pigtails are for hard to reach places and intended for first stage regulators with pressure taps in either upstream or downstream positions.

Pressure Test Flexible Rubber Pigtail MARSHALL EXCELSIOR

ME10BTK-1-01

Dwyer U-Tube Manometer are to be attached to a vertical steelsurface with magnets behind scale. If necessary, attach using screws and bolts. A hose included with the manometer.

1222-16

Dwyer U-Tube Manometer

Dwyer U-Tube Manometer Kit - Series 1211

• Rubber tubing adapter to fit standard 7/16” diameter spud

• 3 ft length 3/16” rubber tubing• 3/4 oz. Bottle Fluorescein green color concentrate with wetting agent

FEATURES: 1211

Manometer - EM151

• Measures pressure to 20” Water Column with .05” resolution

• Rugged rubberized case with built-in magnet• Simple two button operation• Over pressure protection

FEATURES: • Auto reset feature• Auto power off after 5 minutes no activity• Battery life 50 hours with alkaline battery• Optional AC319 soft sided carrying case

available

EM151

(Enlarged)


MER432 Series

ME295-1


237 238

KK


CO71 Hand Held Carbon Monoxide Detector CD100A Combustible Gas Leak Detector CD200 Combustible Gas Leak Detector LPKITPLUS Complete LP Diagnostic Kit


2020 Magnehelic Gauge 0 - 20” WC w/Case and Access (2 Boxes)2020LT Magnehelic Gauge 0 - 20” WC Low Temp to -20F w/Case and Acc (2 Boxes)A432 Case and Accessories for 2020 Magnehelic Gauge


PB04 1/4 Pint Gasiola PLS® 2 Premium Thread and Gasket Sealer with Teflon BrushSS04 1/4 Pint Gasiola Soft-Set Thread Sealant with Teflon Brush TopSS08 1/2 Pint Gasiola Soft-Set Thread Sealant with Teflon Brush TopSS16 1 Pint Gasiola Soft-Set Thread Sealant with Teflon Brush TopNT08 1/2 Pint Gasiola Non Teflon Blue Pipe Sealant with Brush TopNT16 1 Pint Gasiola Non Teflon Blue Pipe Sealant with Brush Top

Gas Detectors

Carbon Monoxide Detector CO71 detects CO levels from 0 to 999 ppm. Its tri-color warning indicates three concentration levels. When dangerous CO levels are reached an audible alert sounds. This device is handheld and powered by a 9V battery.


Magnehelic Gauges

2020

Service Equipment - Pipe Thread Sealant

SS04

PB04

The CD100A is designed to detect combustible gas leaks in residential and small commercial applications. Semiconductor sensor responds instantaneously to all combustible gases. The easily adjusted, steady tic rate can be used in tight quarters where others might not fit.

• 50 ppm minimum detection• Easy one hand operation• Long 18” gooseneck• Sensor provides accurate detection

FEATURES: • Tip light in sensor cover illuminates the

area of the leak• Audio and visual tic rate, fully adjustable• Headphone jack

CD100A

CD200

The CD200 has a long, slim gooseneck probe and a bright LED tip light to find combustible gasleaks in tight areas. Its adjustable alarm, easy one-hand operation and impact resistant storagecase add up to value and convenience.

• 50 ppm minimum detection• Adjustable tick rate to locate leaks quickly

and easily• Visual leak detection by LED indicators• Long 18” gooseneck• Separate user adjustable alarm for predetermined level detection

FEATURES: • Precision sensor detects the smallest leaks• Red LED located on the tip to illuminate

search area• Fast response of less than two seconds to

40% LEL• Includes earphone

LPKITPLUS

The LPKITPLUS is the complete tank to inside appliance test kit for installers and service technicians. Checks primary/secondary gas pressure, verify fittings are leak free, and tests forCO levels in the living space. Kit includes CD100A Combustible Gas Leak Detector, CO71A Carbon Monoxide Detector, and the EM151 Electronic Manometer.

• Simple adjustable tic rate• Easy one hand operation• Long 18” gooseneck• Tip light in sensor cover illuminates the

area of the leak

CD100A COMBUSTIBLE GAS LEAK DETECTOR FEATURES: • Sensor provides accurate detection• Audio and visual tic rate• Headphone jack

• Preset alarms with 3-color warning light and audible alert

• MAX capture• Low battery indicator

CO71A CARBON MONOXIDE DETECTOR FEATURES: • CO detection to 999 ppm• Backlit display• One button auto zero

• Single input to measure positive and negative pressure to 20” wg• Ruggedized, including rubber boot with integral magnet

EM151 ELECTRONIC MANOMETER FEATURES: • Measures in inches water gauge• Auto power-off after 5 minutes of no activity

CO71


239 240

KK


17# 17 lb. Magnesium Anode Bag with 13’ of No. 12 Lead Wire Attached, 1 for 500 Gallon Tank, 2 for 1,000 Gallon Tank 5# 5 lb. Magnesium Anode Bag with 13’ of No. 12 Lead Wire Attached, Generally Used for Piping 9# 9 lb. Magnesium Anode Bag with 13’ of No. 12 Lead Wire Attached, Generally Used for Piping


6A Copper Sulfate Half Cell TesterSulfate Crystals Copper Sulfate Crystals - 12 oz. BottleLug Copper Anode Lug for Attaching Anode to Tank

Anode Test Kit Complete Kit - Digital Multimeter, Copper Sulfate Half Cell and

Copper Sulfate CrystalsRE-5 Electrode Flat Surface Ceramic Plug for General Use on Soil Surfaces, 1-3/8” x 6”Anode Extension Lead Red 12 ft. Extension Lead for Multi MeterMCM50280-50282 Telescoping Ball Top Anode Test Rod with Meter Adapter PlateDM200 Digital Multi Meter with Leads, 600 Volts AC/DCAC504 Carrying Case - 3 Place, Hard Sided


ME530 Saf-T-Lok Male POL LockME530-03 Saf-T-Lok Key for POL, Pipe and Barrell LocksME530PL Saf-T-Lok, Male POL Lock with Padlock Cap, Soft NoseME531-50 Locking Pipe Cap 1/2” FNPTME531-75 Locking Pipe Cap 3/4” FNPTME532-38 Locking Flare Plug 3/8”ME532-50 Locking Flare Plug 1/2”ME533 Locking Acme Cap 1-3/4”ME540 Hose End and Quick Acting Valve Lock - Use with ME540PME540P-KA Master® Padlock with 2-1/2” Deep Shackle - Keyed AlikeME540P-KD Master® Padlock with 2-1/2” Deep Shackle - Keyed Differently

Item No. Description Capacity Platform Dimensions Shipping Weight

1100 Fairbanks Portable Utility Scale 1000 lb. 23-1/2” x 17-3/4” 49” h x 21” w 175 lb.1124 Fairbanks Portable Beam Scale 1000 lb. 17-3/4” x 23-1/2” 42 - 3/4” h 175 lb.854F100P Detecto Portable Platform Scale 1000 lb. 19” x 28” 45” h x 24” w 132 lb.4420 Detecto Platform Bench Scale 350 lb. 10-1/2” x 14-1/2” 27” h 46 lb.

ME530PL

ME540-KA,ME540-KD

Anode Bags

#17

Cathodic Protection Equipment

Copper Sulfate Crystals

Anode Test Kit

Safe-T-Locks are designed to prevent tampering, product theft and/or accidental discharge ofproduct. Fits any size tank valve with a POL or 1-3/4” Acme connection or gas plumbing.

To install, securely screw the plug or cap to the valving or plumbing using the appropriate wrench. Snap locking mechanism into place over plug or cap. Locking mechanism will cover the installation hex or knurl and swivel freely until key is inserted and the lock is removed.

• All brass body for maximum durability• Locking mechanism and key features durable chrome plating• Locking mechanism swivels 360° when

FEATURES:

installed to prevent tampering or removal• Locking mechanism cannot be removed

without key• Universal key for all sizes and styles

ME532Series

ME530, ME530-03


ME531 Series

ME533

Lock Caps and POL Locks

Lock Caps and POL Locks (continued)

ME540,ME540-KA

Scales

Detecto854F100P

Detecto4420

FairbanksSeries 1124

FairbanksSeries 1100

Anode Test RodMCM50280-50282RE-5C Electrode


241 242

L

K

L

Replacement Item No. MEW1 – Serviceman’s Replacement Seal Kit Includes: Qty

MEW4 1-1/4” Acme Motor Fuel Flat Gasket 9 MEW3 1-1/4” Acme Flat Gasket 10 MEW2 1-3/4” Acme Flat Gasket 10 MEW5 2-1/4” Acme Flat Gasket 10 MEW6 3-1/4” Acme Flat Gasket 10 ME220M-02 Male Motor Fuel Connector O-ring 12 568-110-01 POL O-ring 12


55441BI Beam insert by Fairbanks, 0 - 100 lb. x 1/2 lb., (set of 2)2-55444-40 Counter Poise by Fairbanks6P10021X Counter Poise by Detecto2-55444-55 100 lb. Counter Poise Weight by Fairbanks2-554444-56 200 lb. Counter Poise Weight by Fairbanks2-554444-57 400 lb. Counter Poise Weight by Fairbanks6PP100X 100 lb. Counter Poise Weight by Detecto6PP200X 200 lb. Counter Poise Weight by Detecto6PP500X 400 lb. Counter Poise Weight by DetectoC73082 50 lb. Test Weight by Fairbanks110-C006-0A 50 lb. Test Weight by Detecto


945TH Parker Rolo-Flair Flairing Tool


512 Rothenberger 3/16” Thru 1-1/8” Tubing Cutter with Reamer7.0007 Rothenberger Replacement Cutter Wheel for 512


RID 31090 10” RID 31095 14” RID 31040 18” Alum Heavy Duty Straight Pipe WrenchRID 31096 24”RID 31050 36”RID 31010 10” RID 31015 12” RID 31020 14” Steel Heavy Duty Straight Pipe WrenchRID 31025 18” RID 31030 24”


#420 9-1/2”, 5 Adjustments, 1-1/2” Capacity#440 12”, 7 Adjustments, 2-1/4” Capacity#460 16”, 8 Adjustments, 4-1/4” Capacity

SAFETY EQUIPMENT TOOLS & ACCESSORIESScale Parts

• Durable ABS plastic container with storage latch• Labeled with each gasket/O-ring size and

part number for easy identification and reorder purposes

FEATURES: • Preformed insert with individual spaces for

each gasket/O-ring size• All gaskets/O-rings manufactured from UL

Listed approved compounds for LP-Gas and NH3 services

Serviceman’s Replacement Seal Kit MARSHALL EXCELSIOR

MEW1

MEW1 Layout

TOOLS & ACCESSORIES

Flairing Tools

Pipe Cutters

Pipe Wrench

50 lb. Test Weight 945TH

512

004424

#460

Rolo-Flair Flairing Tool 945TH is a single handle, automatic depth guage, that burnishes and flares in one motion.

Channel Lock Tongue and Groove Pliers

NOTE: Right angle teeth grip in all directions. Undercut tongue and groove won’t slip. Patented reinforced edge. Channel lock bluecomfort grip.


243 244

LL


MEP700 Marshall Excelsior Complete Vapor Return Methanol InjectorMEP700-01 Marshall Excelsior Injector Body Only

Item No. Size Color Description

523173 Lg Orange Textured Monkey Grip Glove, Coated Safety Cuff, Insulated523193 Lg Orange Smooth Monkey Grip Glove, Fully Coated Safety Cuff, Foam Insulated531793 Med Brown/Yellow Winter TUF-DUK Vinyl Glove 9-MED Foam Insulated, Driver’s Style531795 Lg Brown/Yellow Winter TUF-DUK Vinyl Glove 10-LRG Foam Insulated, Driver’s Style


INF Flexlight Infinite Lighter


#808 8” Wrench, Capacity 15/16”#810 10” Wrench, Capacity 1-3/16”#812 12” Wrench, Capacity 1-3/8”#815 15” Wrench, Capacity 1-3/4”

Item No. Description Length

MEP120C EZ-Turn Ergonomic Aluminum Acme spanner wrench

13-3/4” for 3-1/4” female Acme caps

MEP120B Aluminum Acme spanner wrench for 1-3/4”, 2-1/4”, 3-1/4” 17-1/2”

and 4-1/4” female Acme caps

TOOLS & ACCESSORIESChannellock Adjustable Wrenches

• Measurement scales on jaws ideal to determine size of nuts, pipe, etc.

• Chrome vanadium steel construction• Ergonomic handle, non protruding jaw

FEATURES:

Methanol Injectors

• 1-1/4” female acme vapor connection• Spark resistant brass connectors and valve• Durable steel construction body• Automotive grade powder coat finish for

maximum corrosion resistance

MEP700 FEATURES: • For use with all multi-valve applications or

where vapor recovery systems are in place• Maximum capacity = 42 ounces• Maximum pressure = 250 PSIG

Gloves

Methanol Injectors

Infinite Lighters

TOOLS & ACCESSORIES

INF Flexlight

#815

523173

531793

Marshall Excelsior’s Methanol Injector MEP700 is gravity fed and provides a fast and efficient method to inject methanol into stationary ASME containers to help prevent condensation from freezing in the propane system.

WARNING: Never attempt to refill the MEP700 injector with methanol while connected to a propane container. In order for the tank and methanol injector vapor equalization to occur, no more than 42 ounces of methanol can be contained within the methanol injector.

MEP700

Heavy Duty Acme Spanner Wrenches MARSHALL EXCELSIOR

MEP120C

MEP120B


245 246

MM

Item No. Packaged

Inlet Auxiliary Inlet Outlet Outlet Item No.

ME412 — 1-5/16” Female Acme — 1”- 20 Male

ME413 ME413P* #60 Male Soft Nose POL

— 1”- 20 Male w/Round Brass Handwheel 1”-20 Male

ME415 ME415P* .9 GPM Excess Flow

— Female POL Male Hard Nose POL

ME416 — .9 GPM Excess Flow Male Hard

— Female POL Female POL Nose POL w/Plastic Handwheel

ME418 —

1-5/16” Female Acme

— 1-5/16” Male Acme/Female

POL w/Quick Closing Poppet

ME420 ME420P* .9 GPM Excess Flow Male 1/4” Female Inverted Flare

Female POL Hard Nose POL with Check

ME421 — .9 GPM Excess Flow Male

— 1-5/16” Male Acme/Female

Hard Nose POL POL w/Quick Closing Poppet 1”-20 Male

ME422 —

1-5/16” Female Acme 1/4” Female Inverted Flare 1-5/16” Male Acme/Female

POL w/Quick Closing Poppet

ME424

—

.9 GPM Excess Flow Male 1/4” Female Inverted Flare 1-5/16” Male Acme/Female

ME42 Hard Nose POL with Check POL w/Quick Closing Poppet

Item No. Packaged

Inlet Outlet Outlet Item No.

ME423 ME423P* .9 GPM Excess Flow Male 1-5/16” Male Acme/Female POL

1”- 20 Male Hard Nose POL with Quick Closing PoppetME474 — 1-5/6” Female Acme

ME475 ME475P* #60 Male Soft Nose POL with

Plastic Handwheel

ME475AR — #60 Male Soft Nose POL with

1”- 20 Male Round Brass Handwheel ME475B — #60 Male Soft Nose POL

ME477 — .9 GPM Excess Flow Male Hard —

Nose POL with Plastic Handwheel

ME481 ME481P* 1”- 20 Female 1-5/16” Male Acme/Female POL

with Quick Closing PoppetME497 — Male Soft Nose POL with Plastic Handwheel

1”- 20 MaleME497AR —

Male Soft Nose POL with Round Brass Handwheel

OUTDOOR & CAMPING ACCESSORIES OUTDOOR & CAMPING ACCESSORIES

WARNING: An excess flow valve will not activate if there is a break or leak downstream of thevalve that does not equal or exceed the closing flow of the valve or if the excess flow valve installed exceeds the flow capacity of the system.

Camping Tees MARSHALL EXCELSIOR

WARNING: An excess flow valve will not activate if there is a break or leak downstream of thevalve that does not equal or exceed the closing flow of the valve or if the excess flow valve installed exceeds the flow capacity of the system. * Packaged option consists of a plastic clamshell

* Packaged option consists of a plastic clamshell

ME412 ME413 ME414

ME416

ME420P

ME418 ME421

ME422 ME425

ME475

ME475B

ME423ME477

ME497 ME497ARME475AR

ME474

Camping Elbows and Assemblies MARSHALL EXCELSIOR


247 248

MM

Item No. Pack. Item No. Inlet Outlet

ME417 — 1/4” MNPT 1”- 20 Male w/Check and O-ringME483 — 1”- 20 Female Cap with Strap —ME484 — 1”- 20 Female 1/4” Hose BarbME485 — 1”- 20 Female 1/4” FNPTME487 ME487P* 1”- 20 Female Female POLME488 ME488P* 1”- 20 Female 1/4” MNPTME491 — 3/8” Male Flare 1”-20 Male w/Check and O-ringME492 ME492P* 1/4” FNPT 1”- 20 Male - No CheckME493 — 9/16”- 18 Male Left Hand 1”-20 Male w/Check and O-ringME494 — 9/16”- 18 Male Left Hand 1”-20 Male - No Check

ME496 — 1/4” Hose Barb 1”- 20 Male Swivel with

Valve Stem and O-ring

Item No. Connection Description Hose Description

MER470 Brass Tee .9 GPM Excess Flow Male Hard Nose POL x Female POL x 1”- 20 Male 12 ft. - 1”-20 Male x 1”- 20 Female

MER471 Brass Elbow .9 GPM Excess Flow Male Hard Nose POL x 1-5/16” Male Acme/Female

12 ft. - 1”-20 Male x 1”- 20 Female POL with Quick Closing Poppet x 1”- 20 Female

MER472 Brass Tee Stay-Longer Propane Kit - .9 GPM Excess Flow Male Hard Nose 5 ft. - .9 GPM Excess Flow Male

POL x Female POL x 1”- 20 Male x 1/4” Female Inverted Flare POL x 1/4” Male Inverted Flare

Stay-Longer Propane Kit - .9 GPM Excess Flow Male Hard Nose POL x 5 ft. - .9 GPM Excess Flow Male Hard

MER473 Brass Tee Female POL x 1”- 20 Male x 1/4” Female Inverted Flare

Nose POL x 1/4” Male Inverted Flare, and 12 ft. - 1”-20 Male x 1”-20 Female

ME417

Camping Fittings MARSHALL EXCELSIOR

OUTDOOR & CAMPING ACCESSORIES OUTDOOR & CAMPING ACCESSORIES

* Packaged option consists of a plastic clamshellME487P

ME483 ME484

ME488 ME491ME487

ME492 ME494 ME496ME493

The Flow-Longer Propane Kits are designed to connect small, portable appliances, normally fueled by disposable LP-Gas cylinders, to the existing LP-Gas fuel supply of a recreational vehicle, cottage, backyard patio, etc. without interrupting the supply of regulated fuel to the system. Flow-Longer eliminates the need to purchase an extra LP-Gas cylinder or several small,disposable type cylinders.

The Stay-Longer Propane Kits are designed to give you new flexibility on how you use your LP-Gas. You can stay longer by hooking up auxiliary LP-Gas cylinders, or you can tap into the RV’s LP-Gas system to fuel portable high-pressure appliances.

All kits include installation instructions and a convenient reusable box for storage.

NOTE: The tee fitting must be installed between the vapor withdrawal valve on your LP-Gas container and the pressure regulator. This properly places the tee fitting in the high pressure portion of the LP-Gas system. Gas connections to the tee fitting are not designed for movementor rotation after installation. Flexing, twisting, or vibration should be avoided.

WARNING: An excess flow valve will not activate if there is a break or leak downstream of thevalve that does not equal or exceed the closing flow of the valve or if the excess flow valve installed exceeds the flow capacity of the system.

Flow-Longer and Stay-Longer Kits MARSHALL EXCELSIOR

MER470

MER471 MER472 MER473

ME485

MER470 (Boxed)


249 250

MM


F276328 Propane or Natural Gas Male Excess Flow Plug, 1/4” Male Pipe Thread x Male PlugF276329 Propane Cylinder Filling Plug, 7/8” Female POL x Male PlugF276330 Propane Gas Coupling Adapter Kit, 1/4” Male Pipe Thread x Male Plug/Quick Connect x POLF276334 Propane Gas Grill “Quick Connect” Adapter, Quick Connect x POL

Propane Accessories


F271161 22” Replacement Propane BBQ Hose and Regulator Assembly w/Appliance End Fitting x

3/8” Female Flare for Type 1 (QCC1) Gas Grill SystemF271715 Propane “Y” Male Adapter w/Handwheel, 2 - 1”- 20 Throwaway Cylinder Threads x POLF271731 30” Distribution/Lantern Post 3 - 1”- 20 Male Throwaway Cylinder Threads x POLF271735 Propane “Y” Female Adapter with Handwheel, 2 - Female QCC-1 x MPOLF273169 Tank Stabilizer, Fits 20 lb., 30 lb., and 40 lb. Cylinders

F273751 Propane Adapter Tee w/Cap and Plug, POL x 1”- 20 (w/Check) Throwaway Cylinder

Thread x Female POLF273758 Propane Bulk Cylinder Adapter w/Handwheel, 1”- 20 Throwaway Cylinder Thread x POLF276132 Propane Bulk Cylinder Adapter (No Handwheel), 1”- 20 Throwaway Cylinder Thread x POLF273759 90º Propane Low Pressure Regulator w/90º Angle, 3/8” Female Pipe Thread x POL- 11”F276136 Propane Low Pressure Regulator, 3/8” Female Pipe Thread x POL- 11”F273760 90º Elbow, POL x 1”- 20 Male Throwaway Cylinder ThreadF276495 Appliance End Fitting, Coupling Nut x 1/4” Male Pipe ThreadG483 Propane Brass Cap


F273701 5’ Propane Hose Assembly

F273702 12’ Propane Hose Assembly, Swivel 1”- 20 Male Throwaway Cylinder Thread x Soft Nose

Excess Flow POL w/HandwheelF273707 5’ Propane Hose Assembly, 1/4” Male Pipe Thread x 3/8” Female Flare

F273711 12’ Propane Hose Assembly, Swivel 1”- 20 Male Throwaway Cylinder Thread x Swivel

1”- 20 Female Throwaway Cylinder ThreadF273716 22” Propane Replacement Barbecue Hose, 3/8” Male Pipe Thread x 3/8” Female FlareF273717 5’ Propane Hose Assembly, 1/4” Female Pipe Thread x 1/4” Male Pipe Thread

F273720 12’ Natural Gas Patio Hose Assembly, 3/8” Female Pipe Thread x 3/8” Male Flare Quick

Connect/Disconnect with Dust Plug and CapF276124 5’ Propane Hose Assembly, 3/8” Male Pipe Thread x 3/8” Female Pipe Thread


F273754 1/4” Male Pipe Thread x 1”- 20 Female Throwaway Cylinder ThreadF273755 1/4” Male Pipe Thread x 1”- 20 Male Throwaway Cylinder ThreadF273757 9/16” Left Hand Thread x POL w/HandwheelF276129 9/16” Left Hand Thread x POLF276130 9/16” Left Hand Thread x 1” - 20 Throwaway Cylinder Thread w/ShutoffF276139 1/4” Male Pipe Thread x POLF273756 1/4” Male Pipe Thread x POL w/HandwheelF276140 Propane Male Throwaway Cylnder Adapter, Throwaway Thread x 1/4” Female Pipe Thread

OUTDOOR & CAMPING ACCESSORIES OUTDOOR & CAMPING ACCESSORIESQuick Connectors

F276328

F276329 F276330 F276334

F271161

F271715

F273758F273169 F276132

F273760

F276495

F273759 F276136

Propane Hoses

F273701

F273707F273711 F273716

F273717 F273720 F276124

Propane Brass Fittings

F273754

F273755

F273756F276139F276129F273757 F276130 F276140


251 252

N N

Propane Butane

Cubic Feet of Air Required to Burn 1 Cubic Foot of Gas 23.5 30.0Cubic Feet of Oxygen Required to Burn 1 Cubic Foot of Gas 5 6.25Cubic Feet of Air Required to Burn 1 lb. of Gas 200 195Ignition Temperature 920-1020 900-1000Maximum Flame Temperature 3600 3625Percent of Gas in Air for Maximum Flame Temperature 4.4 3.5Maximum Rate of Flame Propagation in 1” Tube, inches/second 32 33Limits of Inflammability, Percentage of Gas in Air Mixture Percent at Lower Limit 2.4 1.9 Percent at Maximum Rate of Flame Propagation 4.8 3.8 Percent at Upper Limit 9.5 8.5

Propane Butane

Cubic Feet of CO2 per Cubic Foot of Gas 3.0 3.9Cubic Feet Water Vapor per Cubic Foot of Gas 4.0 5.0Cubic Feet N2 per Cubic Foot of Gas 18.5 23.6Pounds of CO2 per Pounds of Gas 3.0 3.1Pounds of H2O per Pounds of Gas 1.6 1.5Pounds of N2 per Pounds of Gas 12.0 11.8Ultimate CO2 Percent by Volume 13.9 14.1

Propane Butane

Formula C3H8 C4H10

Normal State, 60 F. 30” Mercury Gas GasFreezing Point (or Melting) Degrees in Fahrenheit -310 -210Boiling Point, Degrees in Fahrenheit -44 32Specific Gravity of Vapor (Air = 1) at 60º F, 30” Hg. 1.52 2.00Specific Gravity of Liquid (Water = 1) 60/60 F 0.51 0.58Weight Per Gallon of Liquid at 60º F, lbs. 4.24 4.85Gallons Per Pound of Liquid at 60º F 0.236 0.206BTU Per Gallon (Vapor) 91,500 102,600BTU Per Pound (Vapor) 21,560 21,180BTU Per Cubic Foot (Vapor) 2,520 3,260Latent Heat of Vaporization at Boiling Point, BTU/lb. 185 166Latent Heat of Vaporization at Boiling Point, BTU/gal. 785 807Specific Heat of Gas, BTU/lb./ ºF at 60º F 0.405 0.385Specific Heat of Liquid, BTU/lb./ ºF at 60º F 0.0590 0.550Density of Gas, Pounds Per Cubic Foot 0.116 0.153Density of Liquid, Pounds Per Cubic Foot 31.7 36.0Cu. Ft. of Gas/gal. Liquid at 60º F, 30” Hg. 36.5 31.0Cu. Ft. of Gas/lb. Liquid at 60º F, 30” Hg. 8.55 6.51Vapor Pressure, lbs./sq. in. Gauge — Temperature -10º F 20 — 0º F 28 — 10º F 45 — 32º F 60 — 60º F 100 12 80º F 130 22.5 100º F 190 37 120º F 240 55

Capacity Diameter Length Tank Weight Gallons Liters Inches Millimeter Inches Millimeter Pounds Kilogram 120 454 24 610 68 1727 288 131 150 568 24 610 84 2134 352 160 200 757 30 762 79 2007 463 210 250 946 30 762 94 2387 542 246 325 1230 30 762 119 3023 672 305 500 1893 37 940 119 3023 1062 482 1000 3785 41 1041 192 4877 1983 900

BTU Per Hour With 40% Liquid in Domestic Tank System

Tank Size Water Capacity 20°F (-7°C) Prevailing Air Temp. 60°F (16°C) Prevailing Air Temp. 120 235,008 417,792 150 290,304 516,096 200 341,280 60,720 250 406,080 721,920 325 514,100 937,900 500 634,032 1,127,168 1000 1,088,472 1,978,051

Tank Size Amount of Methanol to Add

150 Gallons One Pint 250 Gallons One Quart 500 Gallons Two Quarts 1000 Gallons One Gallon

Physical Properties of Propane and Butane

GENERAL INFORMATION GENERAL INFORMATION

Combustion Data

Products of Complete Combustion

Standard Domestic Propane Tank Specifications

Vaporization Capacities of Propane Tanks (Approximate)

Removing Water from Tanks

Water in LP-Gas tanks can reduce the efficiency of appliances powered by the propane. To remove water from tanks add one pint of pure methanol for every 100 gallons of the tank’s water capacity.


253 254

N N

Pipe 1/2” 3/4” 1” 1-1/4” 1-1/2” 2” 2-1/2” 3” 4”(Feet) 40 80 40 80 40 80 40 80 40 80 40 80 40 80 40 80 40 80 10 7.1 5.0 15.0 11.3 28.3 22.2 58 47.6 87 73 169 143 269 229 475 410 967 846 15 5.8 4.1 12.2 9.2 23.0 18.1 47.5 38.8 71 59 137 116 219 187 387 334 789 690 20 5.0 3.5 10.5 8.0 19.9 15.6 41.0 33.5 62 51 119 100 189 161 335 289 682 597 30 4.1 2.9 8.5 6.5 16.2 12.7 33.4 27.3 50.1 41.6 97 82 154 131 283 235 556 486 40 3.5 2.5 7.4 5.6 14.0 11.0 28.8 23.5 43.3 35.9 84 71 133 114 236 203 481 421 50 3.1 2.2 6.6 5.0 12.5 9.8 25.7 21.0 36.6 32.1 75 63 119 101 211 182 429 376 60 2.8 2.0 6.0 4.5 11.3 8.9 23.4 19.1 35.2 29.2 68 57 109 92 192 166 391 343 70 2.6 1.8 5.5 4.2 10.5 8.2 21.6 17.7 32.5 27.0 63 53 100 85 177 153 362 317 80 2.4 1.7 5.2 3.9 9.8 7.7 20.2 16.5 30.4 25.2 59 49.6 94 80 166 143 338 296 90 2.3 1.6 4.8 3.7 9.2 7.2 19.0 15.5 28.6 23.7 55 46.7 88 75 156 135 319 279 100 2.2 1.5 4.6 3.5 8.7 6.8 18.0 14.7 27.1 22.5 52 44.2 84 71 148 128 302 264 150 1.8 1.2 3.7 2.8 7.1 5.5 14.6 11.9 22.0 18.2 42.5 35.9 68 58 120 104 246 215 200 1.5 1.1 3.2 2.4 6.1 4.8 12.6 10.3 18.9 15.7 36.7 31.0 59 49.39 104 89 212 185 300 1.2 0.9 2.6 1.9 4.9 3.8 10.2 8.3 15.3 12.7 29.7 25.1 47.5 40.4 84 73 172 151 400 1.0 0.7 2.2 1.7 4.2 3.3 8.8 7.1 13.2 10.9 25.6 21.6 40.9 34.6 73 66 149 130

Length of Schedule 40 Pipe Nominal Size Copper Tubing Type L Nominal Size

Pipe or (Inside Diameter) (Outside Diameter)

Tubing (ft.) 1/2” 3/4” 1” 1-1/4” 1-1/2” 2” 3” 3-1/2” 4” 1/4” 3/8” 1/2” 5/8” 3/4” 10 291 608 1146 2353 3525 6789 19130 28008 39018 49 110 206 348 536 20 200 418 788 1617 2423 4666 13148 19250 26817 34 76 141 239 368 30 161 336 632 1299 1946 3747 10558 15458 21535 27 61 114 192 296 40 137 287 541 1111 1665 3207 9036 13230 18431 23 52 97 164 253 50 122 255 480 985 1476 2842 8009 11726 16335 20 46 86 146 224 60 110 231 435 892 1337 2575 7256 10625 14801 19 42 78 132 203 80 94 198 372 764 1144 2204 6211 9093 12668 16 36 67 113 174 100 84 175 330 677 1014 1954 5504 8059 11227 14 32 59 100 154 125 74 155 292 600 899 1731 4878 7143 9950 12 28 52 89 137 150 67 141 265 544 815 1569 4420 6472 9016 11 26 48 80 124 200 58 120 227 465 697 1343 3783 5539 7716 10 22 41 69 106 250 51 107 201 412 618 1190 3353 4909 6839 9 19 36 61 94 300 46 97 182 374 560 1078 3038 4448 6196 8 18 33 55 85 350 43 89 167 344 515 992 2795 4092 5701 7 16 30 51 78 400 40 83 156 320 479 923 2600 3807 5303 7 15 28 47 73

Length of 1/2” CTS 3/4” IPS 1” IPS 1 1/4” IPS 1 1/2” IPS 2” IPS

Pipe (Feet) SDR 7.00 SDR 11.0 SDR 11.00 SDR 10.00 SDR 11.00 SDR 11.00

(0.445)* (0.860)* (1.077)* (1.328)* (1.554)* (1.943)*

30 762 4292 7744 13416 20260 36402 40 653 3673 6628 11482 17340 31155 50 578 3256 5874 10176 15368 27612 60 524 2950 5322 9220 13924 25019 70 482 2714 4896 8483 12810 23017 80 448 2525 4555 7891 11918 21413 90 421 2369 4274 7404 11182 20091 100 397 2238 4037 6994 10562 18978 125 352 1983 3578 6199 9361 16820 150 319 1797 3242 5616 8482 15240 175 294 1653 2983 5167 7803 14020 200 273 1539 2775 4807 7259 13043 225 256 1443 2603 4510 6811 12238 250 242 1363 2459 4260 6434 11560 275 230 1294 2336 4046 6111 10979 300 219 1235 2228 3860 5830 10474 350 202 1136 2050 3551 5363 9636 400 188 1057 1907 3304 4989 8965 450 176 992 1789 3100 4681 8411 500 166 937 1690 2928 4422 7945 600 151 849 1531 2653 4007 7199 700 139 781 1409 2441 3686 6623 800 129 726 1311 2271 3429 6161 900 121 682 1230 2131 3217 5781 1000 114 644 1162 2012 3039 5461 1500 92 517 933 1616 2441 4385 2000 79 443 798 1383 2089 3753

Line Sizing Chart for Liquid Propane Flow in GPM

GENERAL INFORMATION GENERAL INFORMATION

Sizing Pipe Between First and Second Stage Regulators

Based on 2 PSIG pressure drop. Propane at 60º F. Based on Schedule 40/80 steel/iron pipe

Reference: NFPA Pamphlet 54-1996

Plastic Pipe (Polyethylene) Sizing Between First and Second Stage Regulators

*Inside diameter of pipe | Maximum undiluted propane capacities listed are based on a pressure of 10 PSIG first stage setting and 1 PSI pressure drop. Capacities listed are 1000 Btu/hr.


255 256

Acme Fittings ......................... 161 - 164 Adaptors ......................... 161 - 162 Caps, Plugs & Chains ...... 163 - 164Actuators ................................... 51 - 53 Accessories .............................. 53 Rotary ....................................... 53Angle Valve ................................ 88 - 95Anode Equipment .......................... 239Appliance Connectors .....................198ASME Cluster Valves ..................... 209ASME Tank Filler Valves ......... 204 - 205Autogas Dispensers .......................173 Fuel Management Equipment ... 174 Gasguard Nozzles .......... 153 - 154

Back Check Valves ..................... 78 - 81Back Pressure Valves ....................... 81Ball Valves .................................97 - 101Barb Inserts ....................................181Brass Fittings ..................186 - 188, 192 Breakaway Couplings .....................172Bulkheads .......................................169Bulkhead Fittings ............................169Bushings .........................................104Bypass Valves ............................ 71 - 75

Cable Controls ..................... 49, 51, 59Caugthodic Testing Equipment ...... 239Camp Appliance Accessories .. 245 - 248 Assemblies ............................. 246 Elbows .................................... 246 Fittings .................................... 247 Flow-Longer ............................ 247 Stay Longer ............................. 248 Tees ........................................ 245Carburetion .............................169 - 170 Bulkhead Fittings .....................169 Filler Coupling ..........................170Cathodic Protection Equipment ..... 239Channel Locks ............................... 243Channel Locks Adjustable Wrench ... 243Chock Blocks ..................................157Cluster Valves ................................ 209Combination Valves ....................... 200Combustible Gas Indicators ... 237 - 238Con-Stab Fittings ................... 195 - 196Con-Stab Risers (Plastic Pipe) ........197Copper Sulfate Crystals ................. 239Copper Tubing .................................189 Coated Copper Tubing ..... 189 - 190Couplings ........................................104

Breakaway ...............................172Crimped On Hose Ends ..................147Cylinders ................................ 215 - 216 Collar ....................................... 224 Valves .............................. 217 - 223 Wrench ................................... 224

Decals and Signs ................... 225 - 228Dielectric Unions (Fittings) ..............186Dispenser Valves .................... 153 -154Double Check Fill Valves ................ 205Dry Break Valves .................... 151 - 152

Emergency Shutoff Valves ......... 54 - 58 Accessories .............................. 59 Actuators................................... 56 Air Tubing, Connectors, and Accessories .......................... 59 Swing Check ....................105 - 106Engine Fuel Remote Fill Valve ........ 220Excess Flow Valves ................... 75 - 77Filler Coupling .........................160, 170Filler Hose Adapter .........159, 170 - 171Filler Valve ......................165, 212 - 217 ........................................ 204 - 205Filler Valve Adapter ........159, 165 - 166Filling Heads ...................................171Fittings Black Iron .........................103 - 104 Brass ................................103 - 104 Dielectric Unions ......................186 Flare Fittings ................... 187 - 188 Forged Steel ....................103 - 104 Last Chance Adapters ..............185 Pipe Thread Adapters ...... 187 - 188Flex Connectors ..............................150Flanged Internal Valves ........ 33, 35 - 36 ............................................ 39 - 49Flaring Tools ................................... 242Flow-Longer Kits ............................ 247Forklift Cylinder Fuel Valve ............. 220Forklift DOT Multivalve................... 221Fuel Line Hose ....................... 147 - 148Fuel Management Equipment ........ 174

Gas Detectors ........................237 - 238Gas Dispensers ..............................173Gasguard Nozzles .................. 153 - 154Gas Grill Accessories ............. 247 - 250Gas Piping .............................. 191 - 194 Couplings .................................192

Fittings ............................ 192 - 193 Manifold ...................................193 Meter Mounts ..........................193 Meter Termination ....................193 Plastic Pipe ..............................194 Protection ................................194 Risers (Plastic Pipe) .................197 Underground Adapters.............191 Underground Couplings ...........191 Underground System ...............191 Gauges and Accessories ........107 - 118 Accessories ............................. 112 Flanged Four Bolt ..................... 117 Float Gauge .......107 - 114, 116 - 118 Float Gauge Accessories ......... 112 Gauge Ordering Information ........... 115 Road Master Gauges ............... 116 Rotary ......................................118 Stationary Float ........................ 114 Test ......................................... 232 Threaded ..................................118 Universal Dial Kits .................... 116Globe and Angle Valves ............. 88 - 95Gloves ............................................ 244

Hex Plugs .......................................104High Pressure Test Blocks ............. 231Hogtails ..................................... 29 - 30Hoses .................................... 147 - 149 Assemblies ..............................102 Barbs ........................................181 Couplings (Clamp Style) ...........149 Crimped On Hose Ends ...........149 End Fill Check Adapters ............159 End Valves ....................... 153 - 156 End Valve Holster .....................156 End Valve Lock .........................155 Reels ............................... 143 - 146 Smart Hoses ............................148 Swivel Connectors ...................156 Hydrostatic Relief Valve ................... 69

Internal Valves ............................ 31 - 49 Accessories ........................ 49 - 51 Flanged Internal Valves . 33, 35 - 36 ............................................ 39 - 49 Threaded .....31 - 32, 34, 37 - 38, 48

Latches for Internal Valves ............... 49Leak Check Kit ............... 231, 233 - 234

GLOSSARYGLOSSARYLeak Detector (Low Temp.) ............ 229Liquid Transfer Adapters................. 200Liquid Transfer Valves ......................199Liquid Withdrawal Valves ....... 199 - 203Lock Caps .............................. 239 - 240Low Pressure Adapters ................. 232Low Pressure Test Blocks .............. 232

Manometer .................................... 236Manometer Kit ............................... 236Meters ....................................134 - 135 Electronic Meter ......................135 Liquid Meter ............................134 Positive Displacement Meter ...134Methanol Injectors ......................... 244Motors ............................................133Multipurpose Valves .............. 201 - 203 Filler/Withdrawal ............. 201 - 203 Multi-Service Valve ......... 207 - 208, .........................................210 - 212 Withdrawal ...................... 201 - 203

Needle Valves .................................. 81Nipples ............................................104

O-rings ........................................... 242Outdoor and Camping Accessories ........................................ 245 - 250 Camping Assemblies .............. 246 Camping Elbows ..................... 246 Camping Fittings ..................... 247 Camping Tees .......................... 245 Flow-Longer Kits ..................... 247 Propane Accessories .............. 249 Propane Brass Fittings ............ 250 Propane Hoses ....................... 250 Quick Connectors ................... 249 Stay-Longer Kits ...................... 248

Pigtails ....................................... 29 - 30Pipe Fittings (Polyethylene) .... 195 - 196 Coupling Tools ..........................196 Couplings ........................ 195 - 196 Elbows .....................................195 Gas Tubing ................................194 Reducer couplings ...................195 Reducing Tees ..........................195 Repair Couplings ......................196 Risers .......................................197 Self-Tapping Tee .......................196 Tees ................................ 195 - 196

Pipe Fittings, Valves, & Strainers (Steel) 45 Degree Elbow .....................103 90 Degree Elbow .....................103 Bushings ..................................104 Caps .........................................104 Couplings .................................104 Globe and Angle Valves ....... 88 - 95 Nipples .....................................104 Square Head Plugs ..................104 Tees .........................................103 Unions ......................................104 Y-Strainers ................................. 96Pipe Thread Sealant ....................... 238Plant and Vehicle Remote Controls ...... ........................................ 136 - 142Plugs (Hex) .....................................104Pneumatic Control / E-Stop Kit ......... 59POL Adapters ........................ 181 - 185POL Filler Couplings .......................168POL Cap and Plugs .........................182POL Locks ............................. 239 - 240Pressure Gauges ............................176Pressure Gauge Adapter ........ 231 - 235Pressure Gauge Snubbers ............. 229Pressure Test Accessories ............. 232Pressure Test Kit ............ 231, 233 - 234 Pressure Test Gauge ...................... 232Pumps ....................................119 - 122 Blackmer Pump ................119 - 122 Blackmer Pump Part List ... 123 - 126 Corken Pump .................. 127 - 130 Corken Pump Part List .... 131 - 132QCC Adapters .................................180QCC Cap .........................................177QCC Connectors .............................177Quick Acting Dispensing Valves ......165Quick Acting Toggle Valves ..............166Quick Closing Couplings .................166Quick Connectors (for Camping) .... 249Quick Filler Couplings .....................170

Rain Caps ........................................214Reducing Couplings ........................195Reels ...................................... 143 - 146 Reel Anatomy ..........................143 Reel Part List............................144Registers ........................................135Regulators ................................... 1 - 20 2 PSI Service .............................. 7 2 PSIG ....................................... 24

Automatic Changeover ............. 23 Commercial / Industrial ........... 7 - 8, .......................................13 - 14, 18 Direct .................................. 27 - 28 First Stage High Pressure .......... 8, .............................................11 - 12 First Stage ................................ 21 First Stage Excela-Flo ............. 1 - 2 Governor ............................. 25 - 26 High Pressure ......................27 - 28 Integral Two Stage Compact ... 4 - 5 Liquid Backpressure ...................17 POL Double Stage .................... 24 Pressure Reducing .....................15 Second Stage ............................ 21 Second Stage Dielectric Union ... 22 Second Stage Domestic .............. 3 Second Stage Low Pressure .......13 Second Stage Light Commercial . 14 Single Stage Low Pressure ........14 Twin Stage .......................... 22 - 23Relief Valves ............................... 60 - 67 External ................... 63 - 64, 66, 69 Flanged Full Internal ................. 67 Full Internal ......................... 66 - 67 Hydrostatic ................................ 69 Internal ...................................... 70 Pipe-aways ................................ 66 Quad-port Manifold ................... 60 Rain Caps .............. 42, 45 - 46, 214 Semi Internal ............................. 65Replacement Seal Kit .................... 241Risers (Plastic Pipe) ........................197

Safety Equipment .................. 177 - 241 Cathodic Protection ................ 239 Decals and Signs ............ 225 - 228 Gas Detectors ................. 237 - 238 High Pressure Test Blocks ....... 231 Hose Barbs ............................. 230 Leak Detector (Low Temp.) ..... 229 Low Pressure Adapters ........... 232 Low Pressure Test Blocks ....... 232 Manometer ............................. 236 Manometer Kit ........................ 236 Pipe Thread Sealant ................ 238 Pressure Gauge Snubbers ...... 229 Pressure Test Accessories ...... 232 Pressure Test Kit ..... 231, 233 - 234 Pressure Test Gauge ............... 232


257 258

GLOSSARYSafety Shutdown Systems .... 136 - 142Scales ............................................ 240 Scale Parts .............................. 241Service Valves ........................ 206 - 212Sight Flow Swing Check Valves ........... .........................................105 - 106Smart Hoses ...................................148Spanner Wrench ............................ 243Stainless Flex Connector ................150Stainless Steel Tubing .....................190Stay-Longer Kits ............................ 248Swing Check Valve ..................105 - 106Switches (Palm Valve) ...................... 59Swivel Connectors ..........................156

Tanks ASME Vapor Draw ...................216 Buffer .......................................216 Home Heating ..........................216 Forklift ......................................216 Rain Caps .................................214 Valves .............................. 199 - 214Test Gauges ................................... 232Tools and Accessories ........... 241 - 244 Channel Locks ......................... 243 Channel Locks Adj. Wrench ..... 243 Flaring Tools ............................ 242 Gas Matches ........................... 244 Gloves ..................................... 244 Methanol Injector .................... 244 O-rings .................................... 242 Pipe Cutters ............................ 242 Pipe Wrench ............................ 242 Replacement Seal Kit .............. 241 Spanner Wrench ...................... 243

Underground Multi-Service Valve ...166

Valves Angle ................................... 88 - 95 ASME/DOT Container Service ........ ........................................ 155 - 158 ASME Tank Filler ..................... 204 ASME Underground Tank ... 209, 211 Autogas ........................... 220 - 221 Back Check .......... 78 - 80, 205, 212 Back Pressure ........................... 81 Ball .....................................97 - 101 Bypass ................................ 71 - 75 Combination ............................ 200 Cylinder ........................... 217 - 223

Dispenser ........................ 164 - 168 Double Check Fill .............. 80, 205 DOT Cylinder ................... 217 - 223 Dry Break ........................ 151 - 152 Emergency Shut-off ............ 54 - 59 Engine Fuel ............................. 220 Engine Fuel Remote Fill .......... 220 Excess Flow ........................ 75 - 77 Filler ........................160, 165 - 170, ................................ 204 - 205, 213

Flanged Internal Valves .................. ......................... 33, 35 - 36, 39 - 47 Forklift Cylinder Fuel ................ 221 Forklift DOT Multivalve ............ 221 Globe and Angle ................. 88 - 95 Hydrostatic Relief ..................... 69 Hose End .................153 - 155, 159 Internal ................................ 31 - 50 Liquid Transfer ................. 199 - 200 Liquid Withdrawal ......................... ........................ 199 - 202, 218, 222 Locking Handle ............................. ......................... 155, 164 - 167, 239 Multipurpose ........................... 203 Multipurpose Filler .......... 201 - 202 Multipurpose Withdrawal ........ 203 Multi-Service ....................210 - 212 Multivalve (420)........................210 Needle ...................................... 81 OPD ........................ 213 - 214, 223 Quick Acting .............................165 Quick Acting Toggle ..................166 Relief ................................... 60 - 70 Relief Manifold(s) ................ 60 - 62 Service ............................ 206 - 212 Swing Check ....................105 - 106 Tank ................................ 199 - 214 Underground Multi-Service ..... 209 Vapor ....................... 205, 207 - 208 Vapor Equalization ....................213 Vapor Return ............................213 Vent ..................................... 82 - 83Vapor Coupling ................................160Vapor Equalization Valve................. 205Vapor Return Valve ..........................213Vapor Service Valve .........................166Vapor Withdrawal Cylinder Valve .... 217, ........................................ 222 - 223Vent Valves .................................82 - 83

Wrenches .............................. 242 - 243

Y-Strainers ........................................ 96

SELLER’S TERMS & CONDITIONS – All sales by MTankCo Supply, LLC (“MTankCo” or“Seller”) are subject to all of the terms and conditions contained herein and upon no other terms and conditions. Seller’s acceptance of Buyer’s order is expressly made conditional upon Buyer’s assent to all of Seller’s terms and Seller objects to any terms or conditions at variance with, different from or additional to the terms set forth herein, unless such terms are set forth in a writing signed by an officer of Seller.

1. PRICES & PAYMENT – Seller, MTankCo Supply, LLC (“MTankCo” or “Seller”) will invoice Buyer and Buyer will pay Seller for Goods sold by Seller. Buyer will also pay theamount of any sales, use, excise or other tax now or hereafter imposed by reason of anysale, delivery, charge or furnishing of any Goods by Seller. Terms of payment, unless otherwise agreed, are cash or cash equivalent before or upon delivery of Goods sold. Allprices are subject to change without notice. Credit terms may be extended solely at the discretion of Seller. If Seller agrees to credit terms and Buyer fails to make timely payment in accordance with those terms or any other agreement separately agreed toby Seller, or Buyers financial condition becomes otherwise impaired or Buyer is unableor unwilling to provide reasonable assurance to Seller of its ability to pay, Seller reservesthe right, in its sole discretion, among other remedies, to refuse to supply Goods exceptupon receipt of cash with order and/or payment in full of all outstanding charges and/orassess and collect from Buyer a monthly late charge at the rate of one and one-half (1½%)per month on any delinquent balance to the extent permitted by law, and/or terminate or suspend the supply of Goods. The Buyer hereby agrees to pay, in addition to all chargesindicated, reasonable attorney fees and costs of collection in the event it is necessary to place this sale in the hands of an attorney to collect any amounts owed by Buyer toSeller. Seller retains a security interest in all items or Goods sold on credit terms for whichfull payment has not been received by Seller including the right to recover possession ofany Goods for which payment has not been made in full.

2. SHIPPING, RISK OF LOSS & RESTOCKING – All sales are made F.O.B. Point ofShipment. In all cases, title shall pass upon delivery to the carrier at point of shipment and thereafter all risk of loss or damage shall be upon Buyer.

Any item that is specially ordered for Buyer that Buyer, for any reason, decides not to purchase is subject to a restocking fee. The deposit on any special order not purchased will be returned to Buyer less the restocking fee, which will be charged by Seller up to 30% of the purchase price of the specially ordered item or items. This restocking fee applies to any items sold and delivered on credit terms for which full payment is not madeand such items are returned or recovered by Seller due to non-payment.

3. CONTINGENCIES – Neither party hereto will be liable to the other for default or delayin the performance of any of its obligations hereunder (except any obligation to make payments when due) due to act of God, accident, fire, flood, storm, riot, war, sabotage, explosion, strike, concerted acts of workers, national defense requirements, governmentallaw, ordinance, rule or regulation, whether valid or invalid, inability to obtain electricity orother type of energy, raw material, labor, equipment or transportation, unavailability ofGoods, or any similar or different contingency beyond its reasonable control which wouldmake performance commercially impracticable whether or not the contingency is of thesame class as those enumerated above, it being expressly agreed that such enumerationshall be nonexclusive. In the event Seller is unable to provide Goods ordered or fill anyorder, Seller will under no circumstances be liable to Buyer or anyone else for anydamages, fees or any other claims beyond return of any deposit or payment. Buyer shallnot, under any circumstances, be entitled to claim or recover for any consequential damages, lost profits, loss of business or income, increased expense or any other type damage due to the failure of Seller to deliver Goods ordered by Buyer regardless of the circumstances.

4. SPECIFICATIONS – Seller does not manufacture Goods it sells and is only a distributorof such Goods for others who manufacture the Goods. Seller makes no alteration to anyGoods sold (including packaging, instructions, warnings and product specifications and descriptions). Accordingly, Seller provides no separate warranty regarding Goods sold toBuyer. Goods sold are only warranted to the extent of any warranty by the manufacturer.Buyer is solely responsible for determining whether or not any Goods ordered or purchased are appropriate for the use or application needed by Buyer. No statements, unless made in writing and signed by Seller, may be relied upon by Buyer regarding anymerchantability, fitness for a particular purpose, specification, warranty, description orother representation as to any characteristics of any Goods sold by Seller to Buyer. Sellerwill provide reasonably available information upon request regarding Goods to Buyer, but Buyer is solely responsible for determining if such Goods are appropriate for the use Buyer intends to make of the Goods purchased. Buyer may reject any Goods whichdo not meet specification(s) of the manufacturer of the Goods. Buyer must inspect allGoods purchased and notify Seller of any unconformity within five (5) days of the deliveryof the Goods to Buyer. Seller will make refund of Buyer’s payment, if any, for such Goodsproperly rejected contingent upon the agreement of the manufacturer or supplier of theGoods to Seller agreeing that specifications for the Goods were not met and the Goodswere properly rejected. If the manufacturer or supplier of Goods to Seller refuses to accept Buyer’s rejection of the Goods, Buyer’s only remedy is against the manufacturer

or supplier of the Goods to Seller and not against Seller. Under no circumstances will any claim of any kind with respect to the conformance of Goods to Specification(s),descriptions or any other characteristic of the Goods, whether or not based on negligence,warranty, strict liability or any other theory of law, result in Buyer being entitled to anyamount greater than the amount actually paid for the nonconforming Goods. The foregoingshall constitute Buyer’s exclusive remedy and Seller’s sole obligation with respect to anysuch claim. THERE ARE NO EXPRESS WARRANTIES BY SELLER OTHER THAN THOSESPECIFIED IN THIS ARTICLE. NO WARRANTIES BY SELLER (OTHER THAN WARRANTYOF TITLE AS PROVIDED IN THE UNIFORM COMMERCIAL CODE) SHALL BE IMPLIEDOR OTHERWISE CREATED UNDER THE UNIFORM COMMERCIAL CODE, INCLUDINGBUT NOT LIMITED TO WARRANTY OF MERCHANTABILITY AND WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE.

5. LIABILITY – Buyer acknowledges that there are hazards associated with the use, installation, incorporation and application of certain Goods and Buyer agrees that Buyer shall be solely responsible for any use, installation, incorporation or application of any Goods purchased and for complying with all relevant reporting obligations under allapplicable laws. Buyer also assumes all responsibility for the suitability and the results ofusing Goods purchased, and incorporation into larger systems, machines, vehicles or anything else. Seller shall not be liable hereunder for any incidental, consequential, indirect or special damages. Buyer hereby agrees to indemnify and hold Seller harmless from any action, lawsuits, demands, claims, losses, expenses, costs, including but notlimited to legal fees, and damages, arising from the injury, illness or death of the Buyer’semployees or anyone else while engaged in the use, installation, incorporation, applicationor any other activities related to any Goods supplied by Seller hereunder, whether or notsuch injury, illness, or death is claimed to have been caused by, resulted from, or was in any way connected with the negligence of the Seller.

6. PATENT INFRINGEMENT – Seller shall have no responsibility for patent, trademarkor copyright infringement for the manufacture, use or sale of the Goods herein which are considered as the design or specification of any other third party, nor shall Seller have responsibility for the structural design or the operating performance of Goods manufactured according to designs and specifications of Buyer, or any other third party, Seller shall have no responsibility for patent infringement of Goods sold by it, which are manufactured or distributed by others.

7. THIRD PARTY USERS – If the user of the Goods sold is not the Buyer, then Buyer agrees to indemnify and hold Seller harmless for any and all loss, damage, and/or expensewhich may at any time be sustained by the Seller by reason of any claims by the user against which the Seller would have a partial or total legal defense or additional legal rights had notice of Seller’s terms and conditions of sale been made part of any sale madeby the Buyer to the user.

8. ARBITRATION – Your acceptance of any Goods purchased from Seller constitutes youragreement to submit any dispute of any kind related in any way to the Product purchased,charges made, and any related action arising from the transaction, including any claims for torts, negligent or intentional breach of contract or otherwise, to binding arbitrationpursuant to the then Rules of the American Arbitration Association for arbitration ofcommercial disputes. The arbitrator shall be the sole judge of whether a claim is subjectto arbitration. This agreement is binding on you, your agents, employees, successors, assigns and any others claiming through you. The arbitration shall be held in Hattiesburg,Forrest County, Mississippi and the arbitrators shall be selected as follows regardless of any contrary provisions of the American Arbitration Association: All arbitrators shall be selected from an area within 100 miles of Hattiesburg, Forrest County, Mississippiand each side shall appoint one arbitrator and the two (2) arbitrators appointed shall agree on a third (3rd) arbitrator. All arbitrators are to be licensed and practicing attorneys.Arbitrators shall apply the law of the State of Mississippi. In the event any party issuccessful in avoiding the agreement to arbitrate or Seller seeks collection of a debt oropen account or claims of Buyer against Seller that would otherwise be subject to arbitration are less than $20,000, Buyer agrees that any lawsuit will be filed only in state or federal courts located in Hattiesburg, Forrest County, Mississippi and Buyer agrees to the personal jurisdiction of those courts over the parties and waives any objections to venue. Mississippi law is to apply to any dispute.

9. ENTIRE CONTRACT, MODIFICATION, SEVERABILITY – These terms and conditions constitute the entire understanding between the parties with respect to the termsgoverning the subject transaction and supersede all prior negotiations, discussions andpreliminary agreements, if any. Except for representations set forth herein, neither partyhas relied on any promises or representations made by the other as an inducement toenter the subject transaction. This Agreement may be supplemented, amended, or modified only by the mutual agreement of the parties. No supplement, amendment, or modification of this Agreement shall be binding unless it is in writing and signed by all parties. If any term or condition herein, or application thereof to any person orcircumstance, shall be deemed to be invalid or unenforceable, the remainder of these terms shall be affected thereby, and all such terms, covenants or conditions shall be valid and shall be enforced to the fullest extent permitted by law.

TERMS & CONDITIONS

7/2018

MTankCo Supply, LLC7074 302 Industrial Dr. | Southaven, MS 38671

ph 800.235.3528 | fax 662.349.1346

MTankCo.com | [email protected]