R E V O LV E R MA G N E T I C S E PA R ATO R

K e n t u c k y O f f i c e

7 7 5 O l d P r e s t o n H w y S .

S h e p h e r d s v i l l e , K Y 4 0 1 6 5

( 5 0 2 ) 3 7 6 - 6 4 4 2

b y :

F O R M O R E I N F O R M A T I O N C O N T A C T U S A T :

N o r t h C a r o l i n a O f f i c e

1 0 8 J o n q u i l C o u r t

M o o r e s v i l l e , N C 2 8 1 1 7

( 7 0 4 ) 4 0 2 - 6 1 9 3 M

M i c h i g a n O f f i c e

2 9 4 4 5 B e c k R o a d

W i x o m , M I 4 8 3 9 3

( 2 4 8 ) 6 1 3 - 3 5 6 3

R E V O L V E R M A G N E T I C S E P A R A T O R S P E C I F I C A T I O N S

Model No. Total No.

Bars

Equipment Nom. Dimensions (inches) Max Flowrate Total Area Betw. Bars

(ft2)

Flow Velocity (in/sec) A B C D E O.A.H. GPM ft

3/sec

RVV-105 105 19.875 54.5 58.125 6 8 59 1/2 300 0.67 4.01 2.00

RVV-120 120 32.375 54.5 58.125 6 8 72 425 0.95 6.23 1.82

RVV-150 150 57.375 54.5 58.125 8 10 97 675 1.50 8.76 2.06

RVV-180 180 82.375 54.5 58.125 8 10 122 900 2.01 11.93 2.02

RVV-210 210 107.375 54.5 58.125 12 14 147 1150 2.56 15.09 2.04

RVV-240 240 132.375 54.5 58.125 12 14 172 1375 3.06 18.26 2.01

E x a c t r a t i o n ’ s R e v o l v e r S e r i e s M a g n e t i c S e p a r a t o r p r o d u c t s

r a i s e t h e c a l i b e r o f o p e r a t i o n f o r s e p a r a t i o n a n d r e m o v a l

o f f e r r o u s m e t a l s f r o m l i q u i d s .

The Revolver is a Variation of the High Standard

High Strength Permanent Magnets Encapsulated in a Stainless Steel Tube

Low Fluid Velocity Typically Less Than 2 in/sec (50 mm/sec) Between Bars

The Standard Magnetic Bars and Chain are Routed Out Over the Edge of

the Tank to Discharge into a Hopper

The Exactration Revolving Cleaning Mechanism Wipes the Bars as They are

Positioned Over the Hopper

Chain Driven Wipers are Less Complex than the Gear and Cam Design of

the Standard Wiper

R E V O L V E R C R I T I C A L D E S I G N F E A T U R E S

W W W . E X A C T R A T I O N . C O M ( 8 4 4 ) 4 4 - E X A C T

These units incorporate magnetic bar technology excellent for removal of magnetic and paramagnetic particles.

Our patent pending automation technology eliminates the mechanical drive wiper system and replaces it with a

revolving wiper system for cleaning of the magnetic bars.

Reduce or Eliminate Disposable Media

Built as a Drop In Module

The Cleaning Section is Outside the Tank

Less Complicated Cleaning Mechanism

Requires Less Space Because it Does Not Have the Large Wiper Assembly

R E V O L V E R A D V A N T A G E S

B R O C H U R E I S S U E 0 1

R E V O L V E R H O W I T W O R K S !

Cold Rolling Coolant Systems

Coil/Strip Cleaning Systems

Coil Grinding Systems

Polishing Filter for Existing Ferrous Coolant Systems

R E V O L V E R A P P L I C A T I O N S

Dirty liquid enters the separator tank at the bottom through a distributor pipe and flows evenly between

the magnetic bars. Perforated distribution panels located behind the magnetic bars insure that the

liquid flows at a uniform velocity throughout the entire magnetic field thus improving the efficiency of

separation. Fluid velocity is held below 2 in/sec (50 mm/sec) providing sufficient time for the ferrous

particles to attract to the magnetic bars. Typically, each bar will coat with 1/8” to 3/16” thick build up of

ferrous particles (swarf), depending upon the dirt generated by the process. The bars are continuously

indexed through the separation tank, then routed out over the edge of the tank to the cleaning section.

Each bar is wiped three (3) times by the upper and lower revolving wiper plates, which discharge the

material directly into a hopper. The clean liquid flows out of the tank at the top through a collector pipe

and into the clean tank.