Download pdf - RENAULT SCENIC 3 (2009 - 2011) MKi + CK (EN_US).pdf

SCENIC 3

This sheet is designed to help you with the installation of a Parrot product and is provided purely for information purposes. The installer is solely responsible for any installation carried out in accordance with the instructions in this sheet and for the quality of the installation. All rights reserved © Copyright 2011 PARROT SA, a French Société Anonyme (Public Limited Company) Registered on the Paris Trade and Companies Register under No. 394 149 496 Reproduction not permitted without authorisation from Parrot SA. Images not contractually binding.

Installation manual: Parrot MKi + Parrot CK3100 range

SCENIC 3

The brand name RENAULT SCENIC 3 and the RENAULT logo are the property of RENAULT. This document is only valid for the vehicle model SCENIC 3® year 2009 to 2011, excluding all other models in the same range and excluding later modifications made to the vehicle by the manufacturer. The Parrot brand name and logos are the exclusive property of Parrot SA.

SCENIC 3


Disassembly 45min

Kit installation 45min

Refitting 45min

Testing 15min

Total 2h30min

NO ACC wire

NO ISO

N/A UNIKA

FRONT SPEAKER TEL mode

ALL MUSIC mode

Fitting time (estimated) / Main features

Tools

Plastic trim removal tools FACOM / BERNER

FACOM DX-25 kit (n°4 tools)

Accessories required

"Please contact your Wholesalers to purchase accessories."

Kram ref. Dealer ref.

CK range 86795 77 11 428 303

MKi range 84795X795 77 11 428 303

Photos not contractually binding

Updating

- TORX screwdriver

- Cutting pliers

- Crimping pliers

- Multimeter or pilot lamp

- Hose clamp

- Electrical tape

- Round male terminals

CK range MKi range

To get the most out of your hands-free kit we recommend that you update your software regularly. The update procedure can be found at

www.parrot.com/usa/support/downloads

http://www.parrot.com/uk/support/downloads

SCENIC 3


Disassembly

SCENIC 3


Disassembly 1 / 4

Using the plastic trim tools, unclip the car stereo surround.

Insert the removal tools into the slots on each side of the radio.

Unclip the radio, pull it up carefully, then remove the trim

tools.

Pull and lift the radio, disconnecting the connector and

the antenna.

1

3

2

4

5 6

Using the plastic trim tools, unclip the cover above the glove

box.

Using the plastic trim tools, unclip the cover located on the

right side of the dashboard.

SCENIC 3


Disassembly 2 / 4

Disconnect the connector for the passenger airbag trigger.

Unscrew screw 1 from the glove box.

Unscrew screw 2 from the glove box.

Unscrew screws 3, 4, 5 and 6 located above the glove box.

7

9

8

10

11 12

Pull the glove box firmly to unclip it and remove it, unplugging the

light connector.

Using the plastic trim tools, unclip the central screen

surround.

1

2

3

4

5 6

SCENIC 3


Disassembly 3 / 4

Disconnect and release the cover. Remove the fuse box cover.

Using the plastic trim tools, unclip the headlight adjuster and

disconnect it.

Using the plastic trim tools, unclip the cover on the left side of the

dashboard underneath the air vent and the side.

13

15

14

16

17 18

Unscrew screw 7. Unscrew screw 8.

7 8

SCENIC 3


Disassembly 4 / 4

Pull firmly to unclip the cover under the steering wheel and

put it on the floor. Do not remove the bottom.

Remove the door seal on the driver’s side.

19 20

SCENIC 3


On this same black connector, remove the small YELLOW wire on

the bottom row.

Finding an ACC wire

Under the steering wheel, just under the fuse box, remove the

large black connector.

Using a jumper or splice, connect a wire.

Pass the wire under the steering wheel towards the radio

housing.

1

3

2

4

5 6

Cut the red wire between the fuse holder and the ISO connector

provided. (Disconnect the blue wire in front of the fuse on connector

84795X795.)

Swap the fuse holders (i.e. the red and orange wires) and connect the

ACC wire. (Connect the wire directly to connector 84795X795.)

SCENIC 3


Pass the cable inside the rain sensor cover towards the cabin light.

Microphone feeding 1 / 2

Using the plastic trim tools, unclip the rain sensor cover.

Glue the support provided onto the cover after cleaning it, connecting the rain sensor.

Using the plastic trim tools, run the cable through the headliner towards the windscreen post on the driver’s

side.

1

3

2

4

5 6

Run the cable replacing the seal on the driver's door.

Pass the cable into the dashboard on the left side.

SCENIC 3


Microphone feeding 2 / 2

Run the cable under the dashboard towards the glove box

housing, attaching it with wire ties.

7

SCENIC 3


Feeding the accessory cable

On the bottom of the glove box, attach the cable to the bar

located above the light hole.

1

Bring it out leaving sufficient length.

2

SCENIC 3


Fitting the hands-free system 1 / 3

Connect the adaptor to the original connector, then pass the connector towards the glove box,

attaching it using wire ties in the glove box housing under the dashboard. Then connect all

of the cables to the blue box as shown in the diagram below. Test everything before

reassembly then slide all the cables behind the glove box and attach them with wire ties .

1

ISO adapter

SCENIC 3



Remove the rubber covers. On the central screen surround.

Feed the cable from the screen through the central hole.

Stick the support (supplied) after cleaning, on the left side near to the

central screen hole and reposition the rubber cover.

1

3

2

4

5 6

Position the kit screen. Feed the cable from the top of the dashboard towards the glove box.

SCENIC 3



Clip the central screen surround back on, reconnecting the screen.

7

SCENIC 3


Testing

Before refitting the system, switch the kit on using the ignition (or by starting the car). By pushing the central knob

of the remote control, check:

1 - That the menu is displayed on the screen. (Language or iPod.) 2 - That the system can be muted. (Click in the blue box.) 3 - That there is no sound coming from the speakers. 4 - That the sound from the voice menu is coming out of the front speakers. 5 - Then turn off the ignition, check that the kit switches off and that the "goodbye" message appears on the screen. (If this fails, reverse the fuses on the kit's wiring harness.) 6 - Pair a telephone with the kit to make a call. (Check that both the microphone and the kit are working.)

SCENIC 3


Reassembly

Refit the system using the following procedure: 1 – Re-install the radio reconnecting the adapter and antenna. 2 - Replace the car stereo surround. 3 - Clip the glove box back in place by pushing hard. (BE CAREFUL with the accessory cable.) 4 - Replace screws 1, 2, 3, 4, 5 and 6 in the glove box. 5 – Re-connect the passenger airbag selector. 6 – Re-fit the right dashboard panel. 7 - Replace the cover above the glove box. 8 – Re-fit the panel under the steering wheel by pushing hard. 9 - Replace screws 7 and 8. 10 – Re-connect and replace the headlight adjuster. 11 – Re-fit the panels on the left side of the dashboard.